3764-60,2,3,5,60T02TC [3M]
64 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, PRESS FIT;型号: | 3764-60,2,3,5,60T02TC |
厂家: | 3M ELECTRONICS |
描述: | 64 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, PRESS FIT |
文件: | 总6页 (文件大小:1192K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
3M™ Four-Wall Header
.100” × .100” Latch/Ejector, Straight, Compliant Pin
3000 Series
•ꢀ Military (with 3M’s 3518 and N3518 polarizing key)
and centerbump polarization
•ꢀ Optional ejector latches
•ꢀ Optional polarizing posts
•ꢀ Mounting holes for securing header to board
•ꢀ Dependable eye-of-the needle pin design
•ꢀ Optional high-temperature insulator
•ꢀ See Regulatory InformationAppendix (RIA) for
chemical compliance information
Date Modified: April 30, 2008
TS-0478-B
Sheet 1 of 3
Physical
Insulation:
Material: Glass Filled Polyester (PBT) Glass Filled Polyester (PCT)
Flammability: UL 94V-0
Color: Gray (PBT), Black (PCT)
Contact:
Material: CopperAlloy
Plating:
Underplating:
100 μ” [ 2.54 μm ] Nickel
WipingArea: 30 μ” [ 0.76 μm ] Gold
Solder Tails: 100 μ” [ 2.54 μm ] Tin Lead or 300u” [7.62 um] Matte Tin (See Ordering Information)
3M Logo, Part Identification Number and Orientation Triangle
Marking:
Electrical
1A
Current Rating:
Insulation Resistance:
Withstanding Voltage:
>1 × 109 Ω at 500VDC
1,000VRMS at Sea Level
Environmental
-55°C to +105°C
Temperature Rating:
UL File No.: E68080
3M is a trademark of 3M Company.
3
For technical, sales or ordering information call
Electronic Solutions Division
Interconnect Solutions
800-225-5373
http://www.3M.com/interconnects/
3M™ Four-Wall Header
.100” × .100” Latch/Ejector, Straight, Compliant Pin
3000 Series
-620T02
Header
-600T02
Header
with No Ejector/Latch
-630T02
Header
with Long Ejector/Latch
for 3M sockets with Strain Relief
with Short Ejector/Latch
for 3M Sockets without Strain Relief
.08
[2.0]
.08
[2.0]
.573 .010
[14.55]
.424 .010
[10.77]
1.07 Ref
[27.2]
.97 Ref
[24.6]
A
.37 Ref
[9.4]
.46 Ref
[11.7]
D
.28
7.1
.100
REF.
2.54
.020
0.51
.185
4.70
.34
.25
6.4
8.6
.13
3.2
.100
REF.
2.54
2X O .100 [2.54]
SEE NOTE #2
POSITION #1
B
A
Notch B
(See Table)
.025 .002 Sq Typ
[0.64]
Notch C
Notch A
(See Table & Note 1)
(See Table & Note 1)
Position 1
Orientation
Triangle
A
.24
[6.1]
.68
[17.3]
.35
[8.9]
.30
[7.6]
.19
[4.8]
.020
[0.51]
.175 .010
[4.44]
A
.21
[5.3]
.16
[4.1]
Section A-A
Inch
(mm)
C
Tolerance Unless Noted
Notes:
.00
.000
.0
1. Notches A & C will accomodate 3M Polarizing Keys 3518 or N3518.
2. Accepts Rear and Front entry mounting hardware:
Rear Entry: #4-24 thread cutting screw
Inch
± .005
± .01
± .1
[ ] Dimensions for
Reference only
3M Part # 3341-5 (.116 [2.95] dia. mounting hole).
Front Entry (Prior to installation of latch): #2-56 Bolt and Nut
3M Part # 3341-6 (.106 [2.69] dia. mounting hole).
TS-0478-B
Sheet 2 of 3
C
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M™ Four-Wall Header
.100” × .100” Latch/Ejector, Straight, Compliant Pin
3000 Series
Polarizing
Notches
Provided
Dimensions
3M Part
Pin Qty
Insertion platen
3442-00XX
Number
A
B
C
D
10
14
16
20
24
26
30
34
40
50
60
64
3793
3314
3408
3428
3627
3429
3440
3431
3432
3433
3372
3764
1.26 (32.1)
1.46 (37.2)
1.56 (39.7)
1.76 (44.8)
1.96 (49.9)
2.06 (52.4)
2.26 (57.5)
2.46 (62.6)
2.76 (70.2)
3.26 (82.9)
3.76 (95.6)
3.96 (100.7)
1.105 (28.07)
1.305 (33.15)
1.405 (35.69)
1.605 (40.77)
1.805 (45.85)
1.905 (48.39)
2.105 (53.47)
2.305 (58.55)
2.605 (66.17)
3.105 (78.87)
3.605 (91.57)
3.805 (96.65)
0.865 (21.97)
1.065 (27.05)
1.165 (29.59)
1.365 (34.67)
1.565 (39.75)
1.665 (42.29)
1.865 (47.37)
2.065 (52.45)
2.365 (60.07)
2.865 (72.77)
3.365 (85.47)
3.565 (90.55)
0.71 (18.0)
0.91 (23.1)
1.01 (25.6)
1.21 (30.7)
1.41 (35.8)
1.51 (38.3)
1.71 (43.4)
1.91 (48.5)
2.21 (56.1)
2.71 (68.8)
3.21 (81.5)
3.41 (86.6)
BC
3442-0048
3442-0049
3442-0050
3442-0051
3442-0052
3442-0053
3442-0054
3442-0055
3442-0056
3442-0057
3442-0058
3442-0059
BC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
.106
.116
[2.95]
R
R
T
T
S
S
.300 Min
[2.69]
or
[7.62]
(See Note 2)
Side to Side
Stackability
Mating
Area
See Note 3
Tail
Section
Compliant Section
4X R .009 Max
[0.23]
.100 .003
[2.54]
4X .002 .001
Section R-R
[0.05]
.060
[1.52]
Position 1
R .020 Sym
[0.51]
.352
[8.94]
Break Edges
.100 .003
[2.54]
B
Section T-T
Recommended Mounting Hole Pattern
Section S-S
Note:
Pin Cross Sections
3. Listed below are the PCB hole sizes and tolerances recommended for use with 3M’s compliant
pin header. The insertion force is designed not to exceed 40 pounds per pin and the withdrawal
force is not less than 10 pounds per pin.
4. Use of snap-in latch/ejectors in either short (N3XXX-650T02XX) or long (N3XXX-660T02XX)
styles, installed or shipped separately. (-5 & -6 snap-in latches are dimensionally and functionally
equivalent to -2 & -3 roll pin latches)
Hole Size for:
Preferred Drilled - ø.0453 ± .0005
Acceptable Drilled - ø.0453 +.0005
-.0010
After Etchback - ø.0460 Max
After Plating - .ø040 ± .003
Board thickness - .093 to .150
Plating:
.001 Minimum Copper plating thickness
.0003 Min Tin plating
If ordering Snap-In style latches separately, please use the chart below
Short Latch
3505-30
Long Latch
3505-31
Color
Gray
Black
High Temp (PPA)
High Temp (PPA)
N3505-30B
N3505-31B
Ordering Information
X XXXX - 6X0T02XX
Prefix:
Blank = Std.Temp Gray (PBT): (TC Plating Req’d)
N = High Temp Black (PCT) (RB Plating Req’d)
Plating suffix:
TC = 30 μ” Gold w/Tin-Lead Tails (App. E2 & C2 Apply)
RB = 30 μ” Gold w/Matte Tin Tails (App. E1 & C1 Apply)
Latch/Ejector System:
0 = No latch/ejectors
2 = Short latch/ejectors
3 = Long latch/ejectors
5 = Short, Snap-In Latch/Ejectors
6 = Long, Snap-In Latch/Ejectors
3M Part Number
Assembly Equipment: Use 3442-00XX platen (see chart above) and
appropriate commercial arbor press to press header into pc board.
TS-0478-B
Sheet 3 of 3
3M is a trademark of 3M Company.
3
For technical, sales or ordering information call
Electronic Solutions Division
Interconnect Solutions
800-225-5373
http://www.3M.com/interconnects/
Regulatory Information Appendix
3M Electronic Solutions Division/Interconnect
EUROPE
Appendix E1: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product is RoHS Compliant 2005/95/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E2: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/747/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E3: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as
amended by Commission Decision 2005/618/EC.
This product contains lead in the solder tail area in excess of the maximum concentration value allowed.
Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information
provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E4: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/717/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.product Warranty stated below.
RIA-2217A-D
Appendix E5: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in excess of the maximum concentration value allowed but is compliant by exemption under
Item 6 of the Annex to the Directive.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
CHINA
Appendix C1: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means
that the product or part does not contain any of the following substances in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix C2: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that
the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with
3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the
product Warranty stated below.
RIA-2217A-D
Appendix C3: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that
the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with
3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the
product Warranty stated below.
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness
is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order
shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of 90 days from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING,
BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty
period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where
prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the
legal theory asserted.
3M Electronic Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
U.S.A.
1-800-225-5373
www.3m.com/interconnects
Please recycle. Printed in USA.
© 3M 2008. All rights reserved.
RIA-2217A-D
3M is a trademark of 3M Company.
相关型号:
©2020 ICPDF网 联系我们和版权申明