CP2-SB110-G1-TG30 [3M]
110 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, PRESS FIT, SOCKET;型号: | CP2-SB110-G1-TG30 |
厂家: | 3M ELECTRONICS |
描述: | 110 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, PRESS FIT, SOCKET |
文件: | 总5页 (文件大小:941K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
3M™ CP2 Press-Fit Socket
2 mm Type B, 95, 110, and 125 Signal Contacts, RightAngle
CP2 Series
•ꢀ 25 mm basic system unit
•ꢀ 50 mm module
•ꢀ Designed according to IEC 61076-4-101 and IEC 60352-5
Standards
•ꢀ 2 mm grid spacing allows for high signal density at low cost
•ꢀ “Eye of the Needle” compliant pin press-fit design helps
reduce manufacturing time and cost
•ꢀ Additional grounding row available for improved ground
bounce and EMI immunity
•ꢀ Mates with 5 row 3M™ MetPak™ HM, and CP2 headers
•ꢀ End-to-end stackable with 5 row 3M™ MetPak™ HSHM,
HM, and CP2 sockets
•ꢀ See Regulatory InformationAppendix (RIA) for chemical
compliance information
Date Modified: February 29, 2008
TS-2268-A
Sheet 1 of 2
Physical
Insulation:
Material: High Temperature Thermoplastic (LCP)
Flammability: UL94V-0
Contact:
Material: CopperAlloy
Plating: See Ordering Information
Mechanical
Mating Force: ≤ 0.75N/PIN
Withdrawl Force: ≥ 0.15N/PIN
Mating and Un-mating Operations: 50
Electrical
Electrical Load: 1.0A at +70°C
Contact Resistance: ≤ 20 mΩ
Insulation Resistance: ≥ 10,000 MΩ
TestVoltage: 750VACRMS
Environmental
Temperature Rating: -55°C to +125°C
PCB Data
Recommended PCB Plated Through Hole: Φ 0.6 0.05 mm
Drill hole diameter: Φ 0.7 0.02 mm
Hole platings Cu 25~50 μm, Sn or SnPb<10 μm
PCB thickness: 1.4-4.2 mm
Press-In Force: ≤ 204 N/pin on nominal hole diameter
Retention Force: ≥ 13.5 N/pin on nominal hole diameter
3M and MetPak are trademarks of 3M Company.
For technical, sales or ordering information call
800-225-5373
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M™ CP2 Press-Fit Socket
2 mm Type B, 95, 110, and 125 Signal Contacts, RightAngle
CP2 Series
"A"
mm
[Inch]
Tolerance Unless Noted
.0
.00
0.
1
0.13
0.3
mm
[ ] Dimensions for
Reference only
"B"
Signal Contact
Dimension A
Dimension B
Quantity
"B"
95
38.00
44.00
50.00
36.00
42.00
48.00
110
125
Reccommended PCB Layout
Ordering Information
CP2-SBXXX-X1-XXXX
Number of Signal Contacts:
095,110 and 125
Plating Options
TG30= 30~40 μ “ Gold Contact Area
100~200μ “ Bright Tin-Lead
50~80μ “ Nickel Underplate
(RIA E2 &C2 apply)
FJ=
10~20μ “ Gold Contact Area
200~300μ “ Matte Tin
Shield Options:
50~80μ “ Nickel Underplate
(RIA E1 &C1 apply)
G= Upper Shield
Blank= No Shield
KR=
30~40μ “ Gold Contact Area
200~300μ “ Matte Tin
50~80μ “ Nickel Underplate
(RIA E1 &C1 apply)
• This diagram serves only for Part Number descriptive definitions.
PLEASE CONTACT YOUR LOCAL SALES REPRESENTATIVE FOR CUSTOMER SPECIFIC PROGUCT CONFIGURATIONS.
TS-2268-A
Sheet 2 of 2
3M and MetPak are trademarks of 3M Company.
For technical, sales or ordering information call
800-225-5373
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
Regulatory Information Appendix
3M Electronic Solutions Division/Interconnect
EUROPE
Appendix E1: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product is RoHS Compliant 2005/95/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E2: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/747/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E3: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as
amended by Commission Decision 2005/618/EC.
This product contains lead in the solder tail area in excess of the maximum concentration value allowed.
Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information
provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E4: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/717/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
RIA-2217B-D
Appendix E5: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in excess of the maximum concentration value allowed but is compliant by exemption under
Item 6 of the Annex to the Directive.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
CHINA
Appendix C1: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means
that the product or part does not contain any of the following substances in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix C2: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that
the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with
3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the
product Warranty stated below.
RIA-2217B-D
Appendix C3: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that
the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with
3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the
product Warranty stated below.
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness
is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order
shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the
warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except
where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of
the legal theory asserted.
3M Electronic Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
U.S.A.
1-800-225-5373
www.3m.com/interconnects
Please recycle. Printed in USA.
© 3M 2008. All rights reserved.
RIA-2217B-D
3M is a trademark of 3M Company.
相关型号:
CP2-SB110-G1-TGFJ
HEADER CONNECTOR,PCB MNT,PLUG,110 CONTACTS,SKT,0.079 PITCH,COMPLIANT FIT TERMINAL
3M
CP2-SB110-G1-TGKR
Board Connector, 110 Contact(s), 5 Row(s), Female, Right Angle, 0.079 inch Pitch, Press Fit Terminal, Plug
3M
CP2-SB125-1-FJ
125 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, PRESS FIT, SOCKET, ROHS COMPLIANT
3M
CP2-SB125-1-KR
125 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, PRESS FIT, SOCKET, ROHS COMPLIANT
3M
CP2-SB125-1-TGKR
HEADER CONNECTOR,PCB MNT,PLUG,125 CONTACTS,SKT,0.079 PITCH,COMPLIANT FIT TERMINAL
3M
CP2-SB125-G1-FJ
125 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, PRESS FIT, SOCKET, ROHS COMPLIANT
3M
CP2-SB125-G1-KR
125 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, PRESS FIT, SOCKET, ROHS COMPLIANT
3M
CP2-SB125-G1-TGFJ
HEADER CONNECTOR,PCB MNT,PLUG,125 CONTACTS,SKT,0.079 PITCH,COMPLIANT FIT TERMINAL
3M
CP2-SB125-G1-TGKR
HEADER CONNECTOR,PCB MNT,PLUG,125 CONTACTS,SKT,0.079 PITCH,COMPLIANT FIT TERMINAL
3M
CP2-SC055-1-FJ
HEADER CONNECTOR,PCB MNT,55 CONTACTS,SKT,0.079 PITCH,COMPLIANT FIT TERMINAL,LOCKING
3M
CP2-SC055-G1-FJ
HEADER CONNECTOR,PCB MNT,55 CONTACTS,SKT,0.079 PITCH,COMPLIANT FIT TERMINAL,LOCKING
3M
©2020 ICPDF网 联系我们和版权申明