MP2-S024-41M1-C-TG30 [3M]
24 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, SOLDER, SOCKET;型号: | MP2-S024-41M1-C-TG30 |
厂家: | 3M ELECTRONICS |
描述: | 24 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, SOLDER, SOCKET |
文件: | 总6页 (文件大小:1735K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
3M™ MetPak™ 2-FB Socket
2 mm 4/5-Row, Solder Tail or Press-Fit With Tail Cover, Right Angle
MP2 Series
• End-to-end stackable
• Offset dual-beam contact minimizes
insertion force
• Expanded pin counts
• Protective Push-Cap
• Monoblockable
• Press or heat stake peg
• 12 mm modular units
• Meets global IEC 61076-4-104
Futurebus+® standard
• See Regulatory Information Appendix (RIA)
for chemical compliance information
TS-1115-06
Date Modified: April 11, 2007
Sheet 1 of 4
Physical
Insulation
Material:
High Temp LCP
UL 94V-0
Beige
Flammability:
Color:
Contact
Material:
Copper Alloy
Plating
Underplating:
Wiping Area:
Solder Tails:
50 μ″ (1.27 μm) Nickel
See Ordering Information
See Ordering Information
Electrical
Current Rating:
Insulation Resistance:
Withstanding Voltage:
Signal: 1.5 A - All contacts simultaneously
3
10 MΩ
1000 V
AC
Environmental
Temperature Rating:
-55°C to +125°C
Process Temperature Rating:
Moisture Sensitivity Level:
260°C (Profile per J-STD-020C)
1 (per J-STD-020C)
MetPak is a trademark of 3M Company
Futurebus+ is a registered trademark of the Institute of Electrical and Electronic Engineers, Inc. (IEEE)
UL File No: E68080
3M
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ 2-FB Socket
2 mm 4/5-Row, Solder Tail or Press-Fit With Tail Cover, Right Angle
MP2 Series
21.00
.827
12.45
.490
"A"
1.00
.039
9.30
.366
11.80
.465
"C" TAIL LENGTH
13.50
.531
X
1
2
2.00
6.00
.236
.079
"D" POST LENGTH
TYP.
2.00
.079
TYP.
"B"
4 ROW PRODUCT
mm
23.00
.906
[inch]
12.45
.490
Tolerance Unless Noted
ROW
0
0.0
0.00
E
mm
±3
±0.3 ±0.13
11.30
.445
D
C
B
FOR SPECIAL MONOBLOCKS
CONTACT 3M SALES
REPRESENTATIVE
13.80
.543
[ ] Dimensions for Reference Only
A
1.00
.039
5 ROW PRODUCT
8.00
.315
Note:
1. Refer to IEC 61076-4-104 Futurebus+® global standard.
2. "Press Fit" describes a contact tail having a compliant section designed to make a reliable electrical connection with a plated through-hole
(PTH) in a printed circuit board, typically a "back plane.”
Ordering Information
MP2 - SXXX - X1XX - X - XXXX
Plating Options:
(See Table 3)
C = Capped Solder Tail
Blank = Press-Fit
Rows
4 = 4 Rows
5 = 5 Rows
Contact Count
(See Table 1)
Termination Style
M = Solder Tail (Press Peg)
S = Solder Tail (Heat Stake)
H = Solder Tail, Special high retention
(press peg requiring arbor press for PCB assembly)
(Contact 3M Sales Rep)
Tail Length
(See Table 2)
TS-1115-06
Sheet 2 of 4
P = Press Fit (w/ Tail Cover)
3M
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ 2-FB Socket
2 mm 4/5-Row, Solder Tail or Press-Fit With Tail Cover, Right Angle
MP2 Series
Table 1 - Connector & Row Lengths
Dim. "A"
mm [inch]
Dim "B"
mm [inch]
Pin
Count
Block
Count
Table 2 - Tail & Post Lengths
Rows
024
048
072
096
120
144
168
192
030
060
090
120
150
180
210
240
11.95 [0.471]
23.95 [0.943]
35.95 [1.415]
47.95 [1.889]
10.00
[0.394]
[0.866]
[1.339]
[1.811]
[2.283]
[2.756]
[3.228]
[3.701]
[0.394]
[0.866]
[1.339]
[1.811]
[2.283]
[2.756]
[3.228]
[3.701]
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
Contact-to-PC Board Tail
Termination Option No.
22.00
34.00
46.00
58.00
70.00
82.00
94.00
10.00
22.00
34.00
46.00
58.00
70.00
82.00
94.00
Dim. "C"
Dim. "D"
Solder
Press-Fit*
S1
2.72 [0.107] 5.20 [0.205]
3.53 [0.139] 5.20 [0.205]
2.72 [0.107] 3.57 [0.141]
3.53 [0.139] 3.57 [0.141]
2.72 [0.107] 3.75 [0.148]
3.53 [0.139] 3.75 [0.148]
59.95
[2.36]
S2
71.95 [2.833]
83.95 [3.305]
95.95 [3.778]
11.95 [0.471]
23.95 [0.943]
35.95 [1.415]
47.95 [1.888]
59.95 [2.361]
71.95 [2.833]
83.95 [3.305]
95.95 [3.778]
M1
M2
P1
H1
H2
*Compliant-Pin Tail
Table 3 - Plating
Plating
Suffix
Press-Fit Tails* Solder Tails
Plating Composition
0.25 µm [10 µ"] Min. Au Contact Area
2.54 µm [100 µ"] Min. SnPb Tail Area
1.27 µm [50 µ"] Min. Ni all over
(RIA E2 & C2
apply)
(RIA E3 & C2
apply)
TG
0.76 µm [30 µ"] Min. Au Contact Area
2.54 µm [100 µ"] Min. SnPb Tail Area
1.27 µm [50 µ"] Min. Ni all over
(RIA E2 & C2
apply)
(RIA E3 & C2
apply)
TG30
0.08 µm [3 µ"] Min. Au Contact Area
(RIA E2 & C2
apply)
(RIA E3 & C2 0.67 µm [27 µ"] Min. PdNi Contact Area
TR30
apply)
2.54 µm [100 µ"] Min. SnPb Tail Area
1.27 µm [50 µ"] Min. Ni all over
0.13 µm [5 µ"] Min. Hard Au Contact Area, Lubricated
1.02 µm [40 µ"] Min. PdNi Contact Area
0.10 µm [4 µ"] Min. Pd Contact Area
(RIA E2 & C2
apply)
(RIA E3 & C2
apply)
TR40B
2.54 µm [100 µ"] Min. SnPb Tail Area
1.27 µm [50 µ"] Min. Ni all over
0.25 µm [10 µ"] Min. Au Contact Area
(RIA E1 & C1
apply)
(RIA E1 & C1
apply)
FJ
KR
RF
5.08 µm [200 µ"] Min. Matt Whisker Mitigating Sn Tail Area
1.27 µm [50 µ"] Min. Ni all over
0.76 µm [30 µ"] Min. Au Contact Area
(RIA E1 & C1
apply)
(RIA E1 & C1
apply)
5.08 µm [200 µ"] Min. Matt Whisker Mitigating Sn Tail Area
1.27 µm [50 µ"] Min. Ni all over
1.27 µm [50 µ"] Min. Au Contact Area, Lubricated
5.08 µm [200 µ"] Min. Matt Whisker Mitigating Sn Tail Area
1.27 µm [50 µ"] Min. Ni all over
(RIA E1 & C1
apply)
(RIA E1 & C1
apply)
0.08 µm [3 µ"] Min. Au Contact Area
(RIA E1 & C1
apply)
(RIA E1 & C1 0.67 µm [27 µ"] Min. PdNi Contact Area
apply)
LR
PD
5.08 µm [200 µ"] Min. Matt Whisker Mitigating Sn Tail Area
1.27 µm [50 µ"] Min. Ni all over
0.13 µm [5 µ"] Min. Hard Au Contact Area, Lubricated
1.02 µm [40 µ"] Min. PdNi Contact Area
0.10 µm [4 µ"] Min. Pd Contact Area
(RIA E1 & C1
apply)
(RIA E1 & C1
apply)
5.08 µm [200 µ"] Min. Matt Whisker Mitigating Sn Tail Area
1.27 µm [50 µ"] Min. Ni all over
*Compliant-Pin Tail
TS-1115-06
Sheet 3 of 4
3M is a trademark of 3M Company.
For technical, sales or ordering information call
3M
Interconnect Solutions
http://www.3M.com/interconnects/
800-225-5373
3M™ MetPak™ 2-FB Socket
2 mm 4/5-Row, Solder Tail or Press-Fit With Tail Cover, Right Angle
MP2 Series
6.00
.236
2.00
3X
.079
THESE HOLES CONSTITUTE MODULAR
REPEATING PATTERN
4.00
.157
2.00
.079
1.00
.039
TYP.
A1
4.00
.157
12.00
.472
"B"
+.05
2.05
-.00
l O 0.10
O
+.002
-.000
.081
UNPLATED THROUGH-HOLE
+.10
2.00
.079
1.50
-.00
“D” PLATED THROUGH-HOLE
l O 0.10
O
+.004
-.000
.059
l O 0.10
4X
8.00
.315
3.00
.118
UNPLATED THROUGH-HOLE
RECOMMENDED 4 ROW PCB HOLE
MOUNTING PATTERN
RECOMMENDED 5 ROW PCB HOLE
MOUNTING PATTERN
Table 4 -- HOLE PLATING For TG, TG30, TR30, TR40B FINISHES ONLY
Finished Dia.
mm [in]
Cu Thickness
mm [in]
SnPb Thickness
microns [µ"]
Drilled Hole Dia.
mm [in]
HOLE
"D"
0.65-0.80 [.0256-.0315] 0.025 [.001] min
15 [600] max
0.81-0.86 [.0319-.0339]
Table 5 -- HOLE PLATING For FJ, KR, RF, LR, and PD FINISHES ONLY
Immersion Matte Sn Electrolitic Au
OSP ENTEK
Thickness
microns [µ"]
Finished Dia. Cu Thickness
Drilled Hole Dia.
mm [in]
Hole
Thickness
Thickness
mm [in]
mm [in]
microns [µ"]
microns [µ"]
0.700-0.800
0.025-0.045
0.5 - 2.5
0.1 - 0.5
[4 - 20]
0.2 - 0.5
[8 - 20]
0.830-0.860 [.0330-.0340] or
0.85mm [ #66] TWIST DRILL
"D"
[.0276-.0315]
[0.001-0.002]
[20 - 100]
TS-1115-06
Sheet 4 of 4
3M
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
Regulatory Information Appendix
3M Electronic Solutions Division/Interconnect
EUROPE
Appendix E1: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product is RoHS Compliant 2005/95/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in
excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/
EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E2: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/747/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in
excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/
EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E3: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as
amended by Commission Decision 2005/618/EC.
This product contains lead in the solder tail area in excess of the maximum concentration value allowed.
Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon
information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E4: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/17/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in
excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision
2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in
writing, this information represents 3M’s best knowledge and belief based upon information provided by third party
suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
RIA-2217-A
CHINA
Appendix C1: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits
for Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006,
means that the product or part does not contain any of the following substances in excess of the following maximum
concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium,
polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise
stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by
third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
20
Appendix C2: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits
for Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006,
means that the product or part does contain a substance, as detailed in the chart below, in excess of the following
maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent
chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless
otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information
provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform
with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in
accordance with the product Warranty stated below.
Name and Content of Hazardous Substances or Elements
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the
accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended
application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s
current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in
writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of ninety (90) days from the time of purchase. 3M MAKES NO
OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s
option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for
any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.
3
Electronic Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
800/225-5373
RIA-2217-A
© 3M 2007
www.3M.com/interconnects
相关型号:
MP2-S030-51S2-TR30
Board Connector, 30 Contact(s), 5 Row(s), Female, Right Angle, 0.079 inch Pitch, Solder Terminal, Plug
3M
MP2-S030G-51M1-C-FJ
30 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, SOLDER, SOCKET, ROHS COMPLIANT
3M
©2020 ICPDF网 联系我们和版权申明