N3627-L02 [3M]
48 CONTACT(S), MALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, SOLDER;
| 型号： | N3627-L02 |
| 厂家： | 
3M ELECTRONICS |
| 描述： | 48 CONTACT(S), MALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, SOLDER 连接器 |
| 文件： | 总6页 (文件大小：1118K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
3M™ Four-Wall Condo Header
.100” × .100” RightAngle
3000 Series
•ꢀ Stacked pins conserve space on the circuit board
allowing higher density packaging
•ꢀ Pin quantity to 128 gives design flexibility with
latching
•ꢀ ‘’HDI’’alternative
•ꢀ Accepts standard IDC sockets
•ꢀ Mates with standard flat cable harnesses
•ꢀ Optional high temperature insulator suitable for ‘’no
lead’’soldering operations
•ꢀ High temperature option suitable for reflow soldering
using “paste in hole” techniques
•ꢀ See Regulatory InformationAppendix for chemical
compliance information
Date Modified: June 11, 2008
TS-0774-D
Sheet 1 of 3
Physical
Insulation:
Material: Glass Filled Polyester (PBT), Glass Filled Polyester (PCT) - High Temp Option
Flammability: UL 94V-0
Color: Gray (PBT), Beige (PCT), Black (PCT)
Contact:
Material: CopperAlloy
Plating:
Underplating:
100 μ” [ 2.54 μm ] Nickel - Overall
WipingArea: 30 μ” [ 0.76 μm ] Gold
Solder Tails: 200 μ” [ 5.08 μm ] Tin Lead or Matte Tin (See Ordering Information)
3M Logo, Part Identification Number and Orientation Triangle
Marking:
Electrical
2A (EIA 364-70)
Current Rating:
Insulation Resistance:
Withstanding Voltage:
>1 × 109 Ω at 500VDC
1,000VRMS at Sea Level
Environmental
-55°C to +105°C
Temperature Rating:
260°C - (High Temp PCT insulator verson), single pass, (profile per J-STD-020C)
(PBT insulator version), maximum insulator temperature 191°C (solder wave
process only)
Process Rating:
1 (per J-STD-020C) High Temp. (PCT) versions only
Moisture Sensitivity Level:
UL File No.: E68080
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M™ Four-Wall Condo Header
.100” × .100” RightAngle
3000 Series
-L30X
-L20X
-L00X
Header with Long Ejector/Latch
for 3M Sockets with Strain Relief
Header with Short Ejector/Latch
for 3M Sockets without Strain Relief
Header without Latch Ejectors
.08 [2.0]
.08 [2.0]
.573 ± .010
[14.55]
.424 ± .010
[10.77]
1.28 Ref
[32.5]
1.18 Ref
[29.9]
A
.37 Ref
[9.4]
.46 Ref
[11.7]
D
REF.
.28
7.1
.100
2.54
.020
0.51
.660
16.76
.100
REF.
2.54
.100
2.54
REF.
POSITION #1
A
Position 1
Orientation
Triangle
Notch B
(See Table 1)
Notch C
(See Table 1 & Note 1)
Notch A
(See Table 1 & Note 1)
.020
[0.51]
.24 [6.1]
.16 [4.1]
.025 Sq Typ
[0.63]
.89
[22.6]
.51
[13.0]
.100 [2.54]
REF.
.20 [5.1]
C
.112 ± .01
[2.84]
.035 [0.89]
2X ø .100
TS-0774-D
Sheet 2 of 3
3M is a trademark of 3M Company.
3
For technical, sales or ordering information call
Electronic Solutions Division
Interconnect Solutions
800-225-5373
http://www.3M.com/interconnects/
3M™ Four-Wall Condo Header
.100” × .100” RightAngle
3000 Series
Table 1
Dimensions
Pin
3M Part
Polarizing
Notches
Quantity Number
A
C
D
20
28
3793
3314
3408
3428
3627
3429
3440
3431
3432
3433
3372
3764
1.26 (32.1)
1.46 (37.2)
1.56 (39.7)
1.76 (44.8)
1.96 (49.8)
2.06 (52.4)
2.26 (57.4)
2.46 (62.6)
2.76 (70.2)
3.26 (82.9)
3.76 (95.6)
3.96 (100.7)
0.865 (21.97)
1.065 (27.05)
1.165 (29.59)
1.365 (34.67)
1.565 (39.75)
1.665 (42.29)
1.865 (47.37)
2.065 (52.45)
2.365 (60.07)
2.865 (72.77)
3.365 (85.47)
3.565 (90.55)
0.71 (18.0)
0.91 (23.1)
1.01 (25.6)
1.21 (30.7)
1.41 (35.8)
1.51 (38.3)
1.71 (43.4)
1.91 (48.5)
2.21 (56.1)
2.71 (68.8)
3.21 (81.5)
3.41 (86.6)
BC
BC
32
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
40
48
52
60
68
80
100
120
128
.232
[5.89]
.029 Typ
[0.74]
ø.040 .003
[ 1.02 ]
(After Plating)
ø.100Typ
[2.54]
.100 Typ
[2.54]
Position 1
.100
[2.54]
Recommended Hole Pattern
Notes:
1. Notches A & C will accomodate 3M Polarizing Key (3M Part Number 3518 or N3518).
2. 112 [2.84] tail length suitable for .062 [1.57] thick pc board.
3. Contact your 3M sales representative for custom requirements.
4. Use of snap-in style latch/ejectors in either short (X3XXX-L502XX) or X3XXX-L602XX) styles, installed or shipped
separately (-5 & -6 snap-in latches are dimensionally and functionally equivalent to -2 & -3 roll pin latches)
If ordering Snap-In style latches separately, please use the below chart
Inch
(mm)
Short Latch
3505-30
Long Latch
3505-31
Color
Gray
Tolerance Unless Noted
High Temp (PPA)
High Temp (PPA)
High Temp (PPA)
.00
.000
.0
N3505-30
N3505-30B
N3505-31
N3505-31B
Beige
Black
Inch
± .005
± .01
± .1
[ ] Dimensions for
Reference only
Ordering Information
X3XXX - LX02XX
Blank or UB = 30 μ” [0.76 μm] Gold with Tin Lead Tails (App. E3 & C2 Apply)
RB = 30 μ” [0.76 μm] Gold with Matte Tin Tails (App. E1 & C1 Apply)
Blank = Std. Temp Gray (PBT) (Blank or UB Pltg. Req’d.)
N = High Temp Beige (PCT) (Blank or UB Pltg. Req’d.)
N = High Temp Black (PCT) (RB Plating Req’d)
Latch/Ejector System
0 = No Latch/Ejector Installed
2 = Short, Roll Pin Latch/Ejectors
3 = Long, Roll Pin Latch/Ejectors
3M Part Number
TS-0774-D
Sheet 3 of 3
3M is a trademark of 3M Company.
3
For technical, sales or ordering information call
Electronic Solutions Division
Interconnect Solutions
800-225-5373
http://www.3M.com/interconnects/
Regulatory Information Appendix
3M Electronic Solutions Division/Interconnect
EUROPE
Appendix E1: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product is RoHS Compliant 2005/95/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E2: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/747/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E3: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as
amended by Commission Decision 2005/618/EC.
This product contains lead in the solder tail area in excess of the maximum concentration value allowed.
Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information
provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E4: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/717/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.product Warranty stated below.
RIA-2217A-D
Appendix E5: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in excess of the maximum concentration value allowed but is compliant by exemption under
Item 6 of the Annex to the Directive.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
CHINA
Appendix C1: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means
that the product or part does not contain any of the following substances in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix C2: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that
the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with
3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the
product Warranty stated below.
RIA-2217A-D
Appendix C3: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that
the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with
3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the
product Warranty stated below.
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness
is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order
shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of 90 days from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING,
BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty
period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where
prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the
legal theory asserted.
3M Electronic Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
U.S.A.
1-800-225-5373
www.3m.com/interconnects
Please recycle. Printed in USA.
© 3M 2008. All rights reserved.
RIA-2217A-D
3M is a trademark of 3M Company.
相关型号：
N3627002UB
Board Connector, 48 Contact(s), 4 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Terminal, Latch & Eject, Black Insulator
3M
N3627303UB
Board Connector, 48 Contact(s), 4 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Terminal, Latch & Eject, Black Insulator
3M
©2020 ICPDF网 联系我们和版权申明