N7E50-D516PG-30 [3M]
50 CONTACT(S), MALE, RIGHT ANGLE PCMCIA CONNECTOR, SURFACE MOUNT, ROHS COMPLIANT;
| 型号： | N7E50-D516PG-30 |
| 厂家： | 
3M ELECTRONICS |
| 描述： | 50 CONTACT(S), MALE, RIGHT ANGLE PCMCIA CONNECTOR, SURFACE MOUNT, ROHS COMPLIANT PC 连接器 |
| 文件： | 总5页 (文件大小：619K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
3M™ CF Card Header
CompactFlash Type I, Low Profile, Surface Mount
7E50 Series
• Meets CFA standards
• 4.0 mm low profile height
• Single row solder tails with 0.635 mm spacing
• Ejector option for easy removal of CF Card
• See Regulatory Information Appendix (RIA)
for chemical compliance information
Date Modified: September 19, 2007
TS-0747-C
Sheet 1 of 3
Physical
Insulation
Material:
Liquid Crystal Polymer (LCP)
UL 94V-0
Beige
Flammability:
Color:
Contact
Material:
Plating
Copper Alloy
Underplating:
Wiping Area:
Solder Tails:
Marking
100 µ″ [ 2.54 µm ] Nickel
Gold Flash over 80/20 Palladium Nickel, Lubricated (see Ordering Information)
Gold Flash (see Ordering Information)
3M Logo, Part Number, Date Code
Electrical
Current Rating:
Insulation Resistance:
Withstanding Voltage:
.5 A
9
8
>1 × 10 Ω at 500 VDC
>1 × 10 Ω at 500 VDC after Environmental Conditioning
500 V
at Sea Level
RMS
Environmental
Temperature Rating:
-55°C to +85°C
Process Rating:
Maximum 260°C (per J-STD-020C)
CompactFlash is a registered trademark of the SanDisk Corporation.
UL File No.: E68080
3
Interconnect Solutions
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
http://www.3M.com/interconnects/
3M™ CF Card Header
CompactFlash Type I, Low Profile, Surface Mount
7E50 Series
Pin Type
Interface Dim A
3.50 [ .138 ]
Pin No.
25, 26
detect
general
power
4.25 [ .167 ]
all other pins
1, 13, 38 & 50
5.00 [ .197 ]
38.74 [ 1.525 ]
32.84 [ 1.293 ]
0.635 [ .0250 ] Typ
0.30 [ .012 ] Typ
2X 0.9 [ .04 ]
4.50 [ .177 ]
6.00 [ .236 ]
2X Ø 2.20
[ .087 ]
1.0 [ .04 ]
2X 3.3
[ .13 ]
15.6
[ .614 ]
13.7
[ .54 ]
Ø1.5 [ .06 ]
1.5 [ .06 ]
Ø 0.44 Typ
[ .017 ]
A
1.37 [ .054 ]
4.0 [ .16 ]
6.70
[ .264 ]
43.03 [ 1.694 ]
45.0 [ 1.77 ]
48.0 [ 1.89 ]
Section A-A
30.48 [ 1.200 ]
Pin 26
1.27 Typ
[ .050 ]
Pin 50
Pin 38
Pin 1
1.27 Typ
[ .050 ]
mm
1.40
[Inch]
Pin 25
[ .055 ]
Pin 13
Tolerance Unless Noted
.79
[ .031 ]
(See note)
(See note)
.000
.00
.0
2X .89
[ .035 ]
mm
± .3 ± .15
[ ] Dimensions for
Reference only
Note: Inverse ( Option “A” ) style shown. For Normal style rotate polarization keys and pin call outs 180°.
Ordering Information
(RIA E1 & C1 apply)
N7E50-X516XX-30
Options: Plating
Options: CF Card Polarization / Solder Tabs / Ejector:
PG = Au Flash over 25 m" [0.64 mm] PdNi Lubricated with Au Flash tails.
Available for "D" product option only.
A = Inverse / with solder tab / ejector acceptable
C = Normal / without solder tab / ejector not acceptable
D = Normal / with solder tab / ejector not acceptable
E = Normal / with solder tab / ejector acceptable
PK = Au Flash over 20 µ" [0.5 µm] PdNi Lubricated with Au flash tails
TS-0747-C
Sheet 2 of 3
3
Interconnect Solutions
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
http://www.3M.com/interconnects/
3M™ CF Card Header
CompactFlash Type I, Low Profile, Surface Mount
7E50 Series
Right Button Ejector 3M Part D7E50-8316-03
( Order Separately )
Centerline of Header
7.0 [ .28 ]
Sliding Length
4.1 [ .16 ]
Ejecting
Length
43.9 Ref
[ 1.73 ]
26.5
[ 1.04 ]
7.0 [ .28 ]
Pushing Length
3M 7E50
17.4
[ .69 ]
Ref
Marking
Area
23.10 Ref
[ .909 ]
25.81 Ref
[ 1.016 ]
4. 0 [ .16 ]
5.4 [ .21 ]
51.4 [ 2.02 ]
Material
5.4 [.21]
Holder: Glass Filled LCP
Button: PBT
Installed
Height
Plate: Stainless Steel
44.20 ± 0.15
2X 2.50 ± 0.15
[ 1.740 ]
[ .098 ]
38.74 ± 0.10
[ 1.525 ]
31.11 ± 0.05
3.50 ± 0.05
[ 1.225 ]
[ .138 ]
0.40 ± 0.03 Typ
[ .016 ]
3.00 ± 0.10
[ .118 ]
0.635 ± 0.03 Typ
7.75 ± 0.05
[ .0250 ]
[ .305 ]
2X 4.5 ± 0.15
[ .18 ]
Pin 26
Pin 1
( Normal )
2X Ø2.20 ± 0.05
[ .087 ]
Pin 26
20.5 Min
[ .81 ]
( Through for M2 )
1.95 ± 0.15
[ .077 ]
Pin 1
( Inverse )
2X Ø1.70 ± 0.03
[ .067 ]
( Through for locating Boss )
The End of P.C. Board
The Direction of Inserting Card
Recommended PCB Solder Pad Pattern
TS-0747-C
Sheet 3 of 3
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3
Interconnect Solutions
http://www.3M.com/interconnects/
Regulatory Information Appendix
3M Electronic Solutions Division/Interconnect
EUROPE
Appendix E1: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product is RoHS Compliant 2005/95/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E2: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/747/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E3: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as
amended by Commission Decision 2005/618/EC.
This product contains lead in the solder tail area in excess of the maximum concentration value allowed.
Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information
provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E4: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/17/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
RIA-2217B-b
CHINA
Appendix C1: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means
that the product or part does not contain any of the following substances in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix C2: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that
the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with
3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the
product Warranty stated below.
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness
is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order
shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the
warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except
where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of
the legal theory asserted.
3
3M Electronics
Interconnect Products
6801 River Place Blvd.
Austin, TX 78726-9000
U.S.A.
Please recycle. Printed in USA.
© 3M 2007. All rights reserved.
RIA-2217B-b
1-800-225-5373
3M is a trademark of 3M Company.
相关型号：
N7E50-M516RA-40-WF
50 CONTACT(S), MALE, RIGHT ANGLE PCMCIA CONNECTOR, SURFACE MOUNT, ROHS COMPLIANT
3M
N7E50-M516RA-50-WF
50 CONTACT(S), MALE, RIGHT ANGLE PCMCIA CONNECTOR, SURFACE MOUNT, ROHS COMPLIANT
3M
©2020 ICPDF网 联系我们和版权申明