LM2902-TR [3PEAK]
1.2MHz, Low-Power 36V Op Amps;
| 型号： | LM2902-TR |
| 厂家： | 
3PEAK |
| 描述： | 1.2MHz, Low-Power 36V Op Amps 放大器 光电二极管 |
| 文件： | 总17页 (文件大小：1254K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LM2904/LM2902
1.2MHz, Low-Power 36V Op Amps
Description
3PEAK
Features
LM2904/2902 types consist of single/dual/quad
channel independent, high gain, internally frequency
compensated operational amplifiers which are
designed specifically to operate from a single power
supply over a wide range of voltages. They may also
be operated from split power supplies. The supply
current is basically independent of the supply
voltage over the recommended voltage range.
Internal Frequency Compensation for Unity Gain
High DC Voltage Gain: 110dB(Typ)
Wide Bandwidth at Unity Gain: 1.2MHz(Typ)
Wide Power Supply Range: 3V to 36V
Dual Supplies: ±1.5V to ±18V
EMIRR IN+: 71dB(Under 1GHz)
Low Supply Current: 100μA(Typ)
These devices are particularly useful in interface
circuits with digital systems and can be operated
from the single common 5VDC power supply. They
are also intended for transducer amplifiers, DC gain
blocks and many other conventional op amp circuits
which can benefit from the single power supply
capability.
Offset Voltage Temperature Drift: 1uV/°C
Input Bias Current: 60pA Typical
Input Common-Mode Voltage Range Includes
Ground
Rail-to-Rail Output
No Phase Reversal for Overdriven Inputs
–40°C to 125°C Operation Range
In the linear mode, the input common-mode voltage
range includes ground and the output voltage can
also swing to both ground and power rail, even
though operated from a single power supply.
ESD Rating:
Robust 2KV – HBM, 2KV – CDM and 500V – MM
The LM2904 is dual channel version available in
8-pin SOP and MSOP packages. The LM2902 is
quad channel version available in 14-pin SOP and
TSSOP packages.
High Performance Drop-In Compatible With
2904,2902 Series Product
Applications
3PEAK and the 3PEAK logo are registered trademarks of
3PEAK INCORPORATED. All other trademarks are the property of
their respective owners.
Walkie-Talkie
Battery Management Solution
Transducer Amplifiers
Summing Amplifiers
Multivibrators
Oscillators
DC Gain Blocks
Pin Configuration(Top View)
LM2904
LM2902
8-Pin SOIC/MSOP
(-S and -V Suffixes)
14-Pin SOIC/TSSOP
(-S and -T Suffixes)
1
2
3
4
8
7
6
5
1
2
3
4
5
6
7
14
13
12
11
10
9
Out A
-In A
+In A
-VS
+VS
Out A
-In A
Out D
-In D
+In D
-VS
Out B
-In B
+In B
A
A
B
D
C
+In A
B
+VS
+In B
+In C
-In C
Out C
-In B
8
Out B
www.3peakic.com.cn
Rev. A.01
1
1.2MHz, Low-Power 36V Op Amps
Order Information
Marking
Information
Model Name
Order Number
Package
8-Pin SOP
Transport Media, Quantity
LM2904-SR
LM2904-VR
LM2902-SR
LM2902-TR
Tape and Reel, 4,000
Tape and Reel, 3,000
Tape and Reel, 2,500
Tape and Reel, 3,000
LM2904
LM2904
LM2902
LM2902
LM2904
8-Pin MSOP
14-Pin SOP
14-Pin TSSOP
LM2902
Note 1
Absolute Maximum Ratings
Supply Voltage: V+ – V– Note 2................................. 42V
Input Voltage................................ V– – 0.3 to V+ + 0.3
Input Current: +IN, –IN Note 3............................ ±20mA
Differential Input Voltage..................................... ±42V
Output Short-Circuit Duration Note 4…............... Infinite
Current at Supply Pins……………............... ±60mA
Operating Temperature Range........–40°C to 125°C
Maximum Junction Temperature................... 150°C
Storage Temperature Range.......... –65°C to 150°C
Lead Temperature (Soldering, 10 sec) ......... 260°C
Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum
Rating condition for extended periods may affect device reliability and lifetime.
Note 2: The op amp supplies must be established simultaneously, with, or before, the application of any input signals.
Note 3: The inputs are protected by ESD protection diodes to each power supply. If the input extends more than 500mV beyond the power supply, the input
current should be limited to less than 10mA.
Note 4: A heat sink may be required to keep the junction temperature below the absolute maximum. This depends on the power supply voltage and how many
amplifiers are shorted. Thermal resistance varies with the amount of PC board metal connected to the package. The specified values are for short traces
connected to the leads.
ESD, Electrostatic Discharge Protection
Symbol
Parameter
Condition
Minimum Level
Unit
HBM
CDM
Human Body Model ESD
MIL-STD-883H Method 3015.8
JEDEC-EIA/JESD22-C101E
2
2
kV
kV
Charged Device Model ESD
Thermal Resistance
Package Type
8-Pin SOP
θJA
158
210
120
180
θJC
43
Unit
°C/W
°C/W
°C/W
°C/W
8-Pin MSOP
14-Pin SOP
14-Pin TSSOP
45
36
35
Rev. A.01
www.3peakic.com.cn
2
1.2MHz, Low-Power 36V Op Amps
Electrical Characteristics
The specifications are at TA = 27° C. VS = 5V, VCM = VOUT =2.5V, RL = 2kΩ, CL =100pF, unless otherwise noted.
SYMBOL
PARAMETER
Input Offset Voltage
CONDITIONS
MIN
TYP
MAX
UNITS
VS = 5 V, VCM = 2.5V and VCM = 0V
VS = 30 V, VCM = 15V and VCM = 0V
-40°C to 125°C
-3
-3
±1
3
3
mV
mV
VOS
VOS TC
IB
±1
1
Input Offset Voltage Drift
Input Bias Current
μV/° C
pA
60
TA = 27 °C
200
0.001
10
TA = 85 °C
pA
IOS
Vn
Input Offset Current
Input Voltage Noise
pA
f = 0.1Hz to 10Hz
f = 1kHz
μVPP
48
en
in
Input Voltage Noise Density
Input Current Noise
nV/√Hz
f = 1kHz
2
2.5
5
fA/√Hz
Differential
Common Mode
CIN
CMRR
VCM
Input Capacitance
pF
dB
V
Common Mode Rejection Ratio
DC, VS = 30V, VCM = 0V to 28V
80
V–
120
Common-mode Input Voltage
Range
VS = 5 V to 30V
V+-2
PSRR
AVOL
Power Supply Rejection Ratio
Open-Loop Large Signal Gain
VS = 5 V to 30V
90
98
120
110
dB
dB
V
VS = 15 V, VO = 1 V to 11 V, RL = 2 kΩ
RLOAD = 10kΩ, VS = ± 15 V
RLOAD = 2kΩ, VS = ± 15 V
RLOAD = 10kΩ , VS = ± 15 V
RLOAD = 2kΩ, VS = ± 15 V
RLOAD ≥ 10 kΩ, VS = 15 V
AV = 1, f =1kHz, IOUT = 0
f = 1kHz, IOUT = 0
14.70
13.70
14.75
13.90
-14.85
-14.25
5
VOH
Output Swing from Supply Rail
V
-14.70
-14.10
V
VOL
Output Swing from Supply Rail
V
mV
Ω
ROUT
RO
Closed-Loop Output Impedance
Open-Loop Output Impedance
Output Short-Circuit Current
Supply Voltage
0.002
120
Ω
ISC
Sink or source current, VS = 30V
20
3
35
mA
V
VS
36
VS = 5V, No load
100
110
62
150
200
μA
μA
°
IQ
Quiescent Current per Amplifier
VS = 30V, No load
RLOAD = 1kΩ, CLOAD = 100pF
RLOAD = 1kΩ, CLOAD = 60pF
f = 1kHz
PM
GM
Phase Margin
Gain Margin
18
dB
MHz
GBWP
Gain-Bandwidth Product
1.2
AV = 1, VS = ± 15V, VOUT = -10V to 10V,
CLOAD =60pF, RLOAD = 10kΩ
SR
FPBW
tS
Slew Rate at unity gain
0.55
V/μs
kHz
μs
Full Power Bandwidth Note 1
17.5
Settling Time, 0.1%
Settling Time, 0.01%
Total Harmonic Distortion and
Noise
2.8
3.1
AV = -1, VOUT = 1V Step
THD+N
Xtalk
f = 1kHz, AV =1, RL = 2kΩ, VOUT = 1Vp-p
0.001
80
%
Channel Separation
f = 1 kHz to 20 kHz
dB
Note 1: Full power bandwidth is calculated from the slew rate FPBW = SR/π • VP-P
www.3peakic.com.cn
Rev. A.01
3
1.2MHz, Low-Power 36V Op Amps
Typical Performance Characteristics
VS = ±15V, VCM = 0V, RL = Open, unless otherwise specified.
Offset Voltage Production Distribution
Unity Gain Bandwidth vs. Temperature
2
1.8
1.6
1.4
1.2
1
1200
Number = 15200pcs
1000
800
600
0.8
0.6
0.4
0.2
0
400
200
0
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature(℃)
Offset Voltage(mV)
Open-Loop Gain and Phase
Input Voltage Noise Spectral Density
150
100
50
200
150
100
50
1000
100
10
VCC= +5V
RL= 1MΩ
CL = 30pF
0
0
-50
-100
-50
-100
1
1
10
100
1k
10k
100k
1M
0.01
1
100
10k
1M
Frequency (Hz)
Frequency(Hz)
Input Bias Current vs. Temperature
Input Bias Current vs. Input Common Mode Voltage
10000
1000
100
1000
VCC= +36V
RL= 1MΩ
CL = 30pF
100
10
1
10
-40
-20
0
20
40
60
80
100 120
8
12
16
20
24
28
Common Mode Voltage(V)
Temperature(℃)
Rev. A.01
www.3peakic.com.cn
4
1.2MHz, Low-Power 36V Op Amps
Typical Performance Characteristics
VS = ±15V, VCM = 0V, RL = Open, unless otherwise specified. (Continued)
Common Mode Rejection Ratio
CMRR vs. Frequency
140
120
100
80
140
120
100
80
60
60
40
40
20
20
0
0
-20
0
5
10
15
20
25
1
100
10k
1M
Common-mode voltage(V)
Frequency(Hz)
Quiescent Current vs. Temperature
Short Circuit Current vs. Temperature
35
30
25
20
15
10
5
140
I
SINK
120
100
80
I
SOURCE
60
40
0
-40 -25 -10
5
20 35 50 65 80 95 110 125
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature(℃)
Temperature(℃)
Power-Supply Rejection Ratio
Quiescent Current vs. Supply Voltage
160
140
120
100
80
120
100
80
60
40
20
0
PSRR+
PSRR-
60
40
20
0
-20
0.01
1
100
10k
1M
3
6
9
12
15
18
21
24
27
30
Frequency(Hz)
Supply Voltage(V)
www.3peakic.com.cn
Rev. A.01
5
1.2MHz, Low-Power 36V Op Amps
Typical Performance Characteristics
VS = ±15V, VCM = 0V, RL = Open, unless otherwise specified. (Continued)
Power-Supply Rejection Ratio vs. Temperature
CMRR vs. Temperature
160
140
120
100
80
160
140
120
100
80
60
60
40
40
20
20
0
0
-40 -25 -10
5
20 35 50 65 80 95 110 125
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature（℃）
Temperature（℃）
EMIRR IN+ vs. Frequency
Small-Scale Step Response
140
120
100
80
Gain=+1
±V=±15V
CL=30pF, RL=1M
60
40
20
0
1
10
100
1000
Frequency(MHz)
Time (5μs/div)
Negative Over-Voltage Recovery
Positive Over-Voltage Recovery
Gain=+10
+V= + 30V
Gain=+10
+V= + 30V
Time (50μs/div)
Time (50μs/div)
Rev. A.01
www.3peakic.com.cn
6
1.2MHz, Low-Power 36V Op Amps
Typical Performance Characteristics
VS = ±15V, VCM = 0V, RL = Open, unless otherwise specified. (Continued)
0.1 Hz TO 10 Hz Input Voltage Noise
Offset Voltage vs Common-Mode Voltage
1.4
1.2
1
0.8
0.6
0.4
0.2
0
0
5
10
15
20
25
Time (1s/div)
Common-mode voltage(V)
Large-Scale Step Response
Positive Output Swing vs. Load Current
6
Gain=+1
T=-40℃
T=25℃
T=130℃
±V=±15V
CL=30pF, RL=1M
5
4
3
2
1
0
0
10
20
30
Time (20μs/div)
I source(mA)
Negative Output Swing vs. Load Current
6
5
4
3
2
1
0
T=-40℃
T=25℃
T=130℃
0
10
20
30
40
I sink (mA)
www.3peakic.com.cn
Rev. A.01
7
1.2MHz, Low-Power 36V Op Amps
Pin Functions
-IN: Inverting Input of the Amplifier.
possible should be used between power supply pins or
between supply pins and ground.
+IN: Non-Inverting Input of Amplifier.
OUT: Amplifier Output. The voltage range extends to
within mV of each supply rail.
V- or -Vs: Negative Power Supply. It is normally tied to
ground. It can also be tied to a voltage other than
ground as long as the voltage between V+ and V– is from
3V to 36V. If it is not connected to ground, bypass it
V+ or +Vs: Positive Power Supply. Typically the voltage
is from 3V to 36V. Split supplies are possible as long
as the voltage between V+ and V– is between 3V and
36V. A bypass capacitor of 0.1μF as close to the part as
with a capacitor of 0.1μF as close to the part as
possible.
Operation
The LM2904/2902 input signal range extends beyond the negative and positive power supplies. The output can even
extend all the way to the negative supply. The input stage is comprised of two CMOS differential amplifiers, a PMOS
stage and NMOS stage that are active over different ranges of common mode input voltage. The Class-AB control
buffer and output bias stage uses a proprietary compensation technique to take full advantage of the process
technology to drive very high capacitive loads. This is evident from the transient over shoot measurement plots in the
Typical Performance Characteristics.
Applications Information
High Supply Voltage and Low Power Consumption
The LM2904/2902 of operational amplifiers can operate with power supply voltages from 3V to 36V. Each amplifier
draws only 100μA quiescent current. The low supply voltage capability and low supply current are ideal for portable
applications demanding HIGH CAPACITIVE LOAD DRIVING CAPABILITY and WIDE BANDWIDTH. The
LM2904/2902 is optimized for wide bandwidth low power applications. They have an industry leading high GBWP to
power ratio and are unity gain stable for 10nf CAPACITIVE load. When the load capacitance increases, the increased
capacitance at the output pushed the non-dominant pole to lower frequency in the open loop frequency response,
lowering the phase and gain margin. Higher gain configurations tend to have better capacitive drive capability than
lower gain configurations due to lower closed loop bandwidth and hence higher phase margin.
Low Input Referred Noise
The LM2904/2902 provides a low input referred noise density of 48nV/√Hz at 1kHz. The voltage noise will grow
slowly with the frequency in wideband range, and the input voltage noise is typically 10μVP-P at the frequency of 0.1Hz
to 10Hz.
Low Input Offset Voltage
The LM2904/2902 has a low offset voltage tolerance of 3mV maximum which is essential for precision applications.
The offset voltage is trimmed with a proprietary trim algorithm to ensure low offset voltage for precision signal
processing requirement.
Low Input Bias Current
The LM2904/2902 is a CMOS OPA family and features very low input bias current in pA range. The low input bias
current allows the amplifiers to be used in applications with high resistance sources. Care must be taken to minimize
PCB Surface Leakage. See below section on “PCB Surface Leakage” for more details.
Rev. A.01
www.3peakic.com.cn
8
1.2MHz, Low-Power 36V Op Amps
PCB Surface Leakage
In applications where low input bias current is critical, Printed Circuit Board (PCB) surface leakage effects need to be
considered. Surface leakage is caused by humidity, dust or other contamination on the board. Under low humidity
conditions, a typical resistance between nearby traces is 1012Ω. A 5V difference would cause 5pA of current to flow,
which is greater than the LM2904/2902 OPA‟s input bias current at +27°C (±1pA, typical). It is recommended to use
multi-layer PCB layout and route the OPA‟s -IN and +IN signal under the PCB surface.
The effective way to reduce surface leakage is to use a guard ring around sensitive pins (or traces). The guard
ring is biased at the same voltage as the sensitive pin. An example of this type of layout is shown in Figure 1 for
Inverting Gain application.
1. For Non-Inverting Gain and Unity-Gain Buffer:
a) Connect the non-inverting pin (VIN+) to the input with a wire that does not touch the PCB surface.
b) Connect the guard ring to the inverting input pin (VIN–). This biases the guard ring to the Common Mode input voltage.
2. For Inverting Gain and Trans-impedance Gain Amplifiers (convert current to voltage, such as photo detectors):
a) Connect the guard ring to the non-inverting input pin (VIN+). This biases the guard ring to the same reference voltage as
the op-amp (e.g., VDD/2 or ground).
b) Connect the inverting pin (VIN–) to the input with a wire that does not touch the PCB surface.
Guard Ring
VIN+
VIN-
+VS
Figure 1
Ground Sensing and Rail to Rail Output
The LM2904/2902 has excellent output drive capability, delivering over 35mA of output drive current. The output stage
is a rail-to-rail topology that is capable of swinging to within 5mV of either rail. Since the inputs can go 100mV beyond
either rail, the op-amp can easily perform „True Ground Sensing‟.
The maximum output current is a function of total supply voltage. As the supply voltage to the amplifier increases, the
output current capability also increases. Attention must be paid to keep the junction temperature of the IC below 150°C
when the output is in continuous short-circuit. The output of the amplifier has reverse-biased ESD diodes connected to
each supply. The output should not be forced more than 0.5V beyond either supply, otherwise current will flow through
these diodes.
ESD
The LM2904/2902 has reverse-biased ESD protection diodes on all inputs and output. Input and out pins cannot be
biased more than 200mV beyond either supply rail.
Feedback Components and Suppression of Ringing
Care should be taken to ensure that the pole formed by the feedback resistors and the parasitic capacitance at the
inverting input does not degrade stability. For example, in a gain of +2 configuration with gain and feedback resistors of
10k, a poorly designed circuit board layout with parasitic capacitance of 5pF (part +PC board) at the amplifier‟s
inverting input will cause the amplifier to ring due to a pole formed at 1.2MHz. An additional capacitor of 5pF across the
feedback resistor as shown in Figure 2 will eliminate any ringing.
Careful layout is extremely important because low power signal conditioning applications demand high-impedance
circuits. The layout should also minimize stray capacitance at the OPA‟s inputs. However some stray capacitance may
be unavoidable and it may be necessary to add a 2pF to 10pF capacitor across the feedback resistor. Select the
smallest capacitor value that ensures stability.
www.3peakic.com.cn
Rev. A.01
9
1.2MHz, Low-Power 36V Op Amps
5pF
10kΩ
VOUT
VIN
CPAR
10kΩ
Figure 2
Driving Large Capacitive Load
The LM2904/2902 of OPA is designed to drive large capacitive loads. Refer to Typical Performance Characteristics for
“Phase Margin vs. Load Capacitance”. As always, larger load capacitance decreases overall phase margin in a
feedback system where internal frequency compensation is utilized. As the load capacitance increases, the feedback
loop‟s phase margin decreases, and the closed-loop bandwidth is reduced. This produces gain peaking in the
frequency response, with overshoot and ringing in output step response. The unity-gain buffer (G = +1V/V) is the most
sensitive to large capacitive loads.
When driving large capacitive loads with the LM2904/2902 (e.g., > 200 pF when G = +1V/V), a small series resistor at
the output (RISO in Figure 3) improves the feedback loop‟s phase margin and stability by making the output load
resistive at higher frequencies.
RISO
VOUT
VIN
CLOAD
Figure 3
Power Supply Layout and Bypass
The LM2904/2902 OPA‟s power supply pin (VDD for single-supply) should have a local bypass capacitor (i.e., 0.01μF to
0.1μF) within 2mm for good high frequency performance. It can also use a bulk capacitor (i.e., 1μF or larger) within
100mm to provide large, slow currents. This bulk capacitor can be shared with other analog parts.
Ground layout improves performance by decreasing the amount of stray capacitance and noise at the OPA‟s inputs
and outputs. To decrease stray capacitance, minimize PC board lengths and resistor leads, and place external
components as close to the op amps‟ pins as possible.
Proper Board Layout
To ensure optimum performance at the PCB level, care must be taken in the design of the board layout. To avoid
leakage currents, the surface of the board should be kept clean and free of moisture. Coating the surface creates a
barrier to moisture accumulation and helps reduce parasitic resistance on the board.
Keeping supply traces short and properly bypassing the power supplies minimizes power supply disturbances due to
output current variation, such as when driving an ac signal into a heavy load. Bypass capacitors should be connected
as closely as possible to the device supply pins. Stray capacitances are a concern at the outputs and the inputs of the
amplifier. It is recommended that signal traces be kept at least 5mm from supply lines to minimize coupling.
A variation in temperature across the PCB can cause a mismatch in the Seebeck voltages at solder joints and other
points where dissimilar metals are in contact, resulting in thermal voltage errors. To minimize these thermocouple
effects, orient resistors so heat sources warm both ends equally. Input signal paths should contain matching numbers
Rev. A.01
www.3peakic.com.cn
10
1.2MHz, Low-Power 36V Op Amps
and types of components, where possible to match the number and type of thermocouple junctions. For example,
dummy components such as zero value resistors can be used to match real resistors in the opposite input path.
Matching components should be located in close proximity and should be oriented in the same manner. Ensure leads
are of equal length so that thermal conduction is in equilibrium. Keep heat sources on the PCB as far away from
amplifier input circuitry as is practical.
The use of a ground plane is highly recommended. A ground plane reduces EMI noise and also helps to maintain a
constant temperature across the circuit board.
www.3peakic.com.cn
Rev. A.01
11
1.2MHz, Low-Power 36V Op Amps
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted.
Please go to web to make sure you have the latest revision.
Revision
Change
Rev. A
Initial Release
Rev. A.01
www.3peakic.com.cn
12
1.2MHz, Low-Power 36V Op Amps
Package Outline Dimensions
SC70-5 /SOT-353
Dimensions
In Millimeters In Inches
Min Max Min Max
Dimensions
Symbol
A
0.900 1.100 0.035 0.043
0.000 0.100 0.000 0.004
0.900 1.000 0.035 0.039
0.150 0.350 0.006 0.014
0.080 0.150 0.003 0.006
2.000 2.200 0.079 0.087
1.150 1.350 0.045 0.053
2.150 2.450 0.085 0.096
A1
A2
b
C
D
E
E1
e
0.650TYP
1.200 1.400 0.047 0.055
0.525REF 0.021REF
0.260 0.460 0.010 0.018
0° 8° 0° 8°
0.026TYP
e1
L
L1
θ
SOT23-5
Dimensions
In Millimeters In Inches
Min Max Min Max
Dimensions
Symbol
A
1.050 1.250 0.041 0.049
0.000 0.100 0.000 0.004
1.050 1.150 0.041 0.045
0.300 0.400 0.012 0.016
0.100 0.200 0.004 0.008
2.820 3.020 0.111 0.119
1.500 1.700 0.059 0.067
2.650 2.950 0.104 0.116
A1
A2
b
C
D
E
E1
e
0.950TYP
1.800 2.000 0.071 0.079
0.700REF 0.028REF
0.300 0.460 0.012 0.024
0.037TYP
e1
L
L1
θ
0°
8°
0°
8°
www.3peakic.com.cn
Rev. A.01
13
1.2MHz, Low-Power 36V Op Amps
Package Outline Dimensions
SOP-8
A2
C
θ
L1
A1
e
E
D
Dimensions
Dimensions In
Inches
In Millimeters
Symbol
Min
Max
Min
Max
A1
A2
b
0.100
1.350
0.330
0.190
4.780
3.800
5.800
0.250
1.550
0.510
0.250
5.000
4.000
6.300
0.004
0.053
0.013
0.007
0.188
0.150
0.228
0.010
0.061
0.020
0.010
0.197
0.157
0.248
E1
C
D
E
E1
e
b
1.270 TYP
0.050 TYP
L1
θ
0.400
0°
1.270
8°
0.016
0°
0.050
8°
Rev. A.01
www.3peakic.com.cn
14
1.2MHz, Low-Power 36V Op Amps
Package Outline Dimensions
MSOP-8
Dimensions
Dimensions In
Inches
In Millimeters
Symbol
Min
Max
Min
Max
A
0.800
0.000
0.760
0.30 TYP
0.15 TYP
2.900
0.65 TYP
2.900
4.700
0.410
0°
1.200
0.200
0.970
0.031
0.000
0.030
0.012 TYP
0.006 TYP
0.114
0.026
0.114
0.185
0.016
0°
0.047
0.008
0.038
E
E1
A1
A2
b
C
D
3.100
0.122
e
b
e
E
3.100
5.100
0.650
6°
0.122
0.201
0.026
6°
D
E1
L1
θ
A1
R1
R
θ
L
L1
L2
www.3peakic.com.cn
Rev. A.01
15
1.2MHz, Low-Power 36V Op Amps
Package Outline Dimensions
TSSOP-14
Dimensions
In Millimeters
E1
E
Symbol
MIN
-
TYP
MAX
1.20
0.15
1.05
0.28
0.19
5.06
6.60
4.50
A
A1
A2
b
-
0.05
0.90
0.20
0.10
4.86
6.20
4.30
-
1.00
-
e
c
c
-
4.96
D
D
E
6.40
E1
e
4.40
0.65 BSC
0.60
L
0.45
0.75
A1
L1
L2
R
1.00 REF
0.25 BSC
-
0.09
0°
-
R1
θ
-
8°
R
θ
L
L1
L2
Rev. A.01
www.3peakic.com.cn
16
1.2MHz, Low-Power 36V Op Amps
Package Outline Dimensions
SOP-14
D
Dimensions
E1
E
In Millimeters
Symbol
MIN
1.35
0.10
1.25
0.36
8.53
5.80
3.80
TYP
1.60
0.15
1.45
MAX
1.75
0.25
1.65
0.49
8.73
6.20
4.00
A
A1
A2
b
e
b
D
8.63
6.00
E
A2
A
E1
e
3.90
1.27 BSC
0.60
A1
L
0.45
0°
0.80
8°
L1
L2
θ
1.04 REF
0.25 BSC
L
L1
θ
L2
www.3peakic.com.cn
Rev. A.01
17
相关型号：
©2020 ICPDF网 联系我们和版权申明