APE1706H-50 [A-POWER]
IC SWITCHING REGULATOR, PSSO5, TO-252, 5 PIN, Switching Regulator or Controller;型号: | APE1706H-50 |
厂家: | ADVANCED POWER ELECTRONICS CORP. |
描述: | IC SWITCHING REGULATOR, PSSO5, TO-252, 5 PIN, Switching Regulator or Controller 开关 |
文件: | 总10页 (文件大小:575K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Advanced Power
Electronics Corp.
APE1706
Preliminary
150KHz, 3A PWM Buck DC/DC Converter
FEATURES
GENERAL DESCRIPTION
-
Output voltage: 3.3V, 5V, 12V and adjustable output version.
The APE1706 series are monolithic IC designed for a step-down DC/DC converter,
and own the ability of driving a 3A load without additional transistor. It saves board
space. The external shutdown function can be controlled by logic level and then come
into standby mode. The internal compensation makes feedback control having good
line and load regulation without external design. Regarding protected function,
thermal shutdown is to prevent over temperature operating from damage, and current
limit is against over current operating of the output switch. If current limit function
occurs and VFB is down below 0.5V, the switching frequency will be reduced. The
APE1706 series operates at a switching frequency of 150KHz thus allow smaller sized
filter components than what would be needed with lower frequency switching
regulators. Other features include a guaranteed +4% tolerance on output voltage
under specified input voltage and output load conditions, and +15% on the oscillator
frequency. The output version included fixed 3.3V, 5V, 12V, and an adjustable type.
The chips are available in a 5-lead TO-252 package.
-
Adjustable version output voltage range, 1.23V to 40V ∂4%.
-
-
-
-
-
-
-
-
-
-
150KHz +15% fixed switching frequency.
Voltage mode non-synchronous PWM control.
Thermal-shutdown and current-limit protection.
ON/OFF shutdown control input.
Short Circuit Protect (SCP).
Operating voltage can be up to 40V.
Output load current: 3A.
5-Lead TO-252 Pb-Free packages.
Low power standby mode.
Built-in switching transistor on chip.
This datasheet contains new product information. Advanced Power Electronics Corp. reserves the rights to modify the product specification without notice. No liability is
assumed as a result of the use of this product. No rights under any patent accompany the sale of the product.
200613071pre-1/9
Advanced Power
Electronics Corp.
APE1706
150KHz, 3A PWM Buck DC/DC Converter
BLOCK DIAGRAM
EN
200mV
V
CC
220mV
1.235V
CURRENT
SOURCE
BIAS
START
UP
2.5V
REGULATOR
REFERENCE
+
COMP.
_
Current
limit
_
COMP.
+
150kHz
OSC.
FB
R2
R1
+
AMP
+
CONTROL
+
DRIVER
3A
SWITCH
_
COMP.
_
COMP.
SW
Vss
Thermal
Shutdown
ADJ : R2=0Ω, R1=OPEN
PIN ASSIGNMENT
The package of APE1706 is TO252-5L; the pin assignment is given by:
( Side View )
Name
VCC
Description
Operating voltage input
( Top View )
SW
Switching output
GND pin
5 SD
4 FB/OUT
3 GND
2 Output
1 VIN
Metal
Tab
GND
VSS
FB
Output voltage feedback control
for ADJ version
TO252-5L
OUT
Output voltage feedback control
for fixed version
EN
ON/OFF Shutdown
2/9
Advanced Power
Electronics Corp.
APE1706
150KHz, 3A PWM Buck DC/DC Converter
ORDER INFORMATION
Order Information
APE1706X - XX
Package Type Output Voltage
H: TO252-5L
33:3.3V
50:5.0V
12: 12V
Blank:ADJ
MARKING INFORMATION
Top Marking
ADJ
1706H
Part number
ID code: internal
WW: 01~52
Y WW XXX
Year : 6 = 2006
FIX
1706H-50
Part number
Output Voltage
ID code: internal
Y WW XXX
WW: 01~52
Year : 6 = 2006
3/9
Advanced Power
Electronics Corp.
APE1706
150KHz, 3A PWM Buck DC/DC Converter
Absolute Maximum Ratings
Characteristics
Symbol
VCC
VEN
VFB
Rating
Unit
Maximum Supply Voltage
+45
V
ON/OFF Pin Input Voltage
-0.3 to VCC
-0.3 to 20
-0.7~45
V
V
Feedback Pin Voltage (for ADJ version)
Output Voltage to Ground (for Fixed version)
Power Dissipation Internally limited
Storage Temperature Range
VOUT
PD
V
( TJ-TA ) / θJA
-65 to +150
-40 to +125
+4.5 to +40
8
W
℃
TST
Operating Temperature Range
Operating Supply Voltage
TOP
℃
VOP
θJC
V
Thermal Resistance from Junction to case
Thermal Resistance from Junction to ambient
℃/W
℃/W
θJA
50
Note : θJA is measured with the PCB copper area(need connect to VSS pins) of approximately 3 in2 (Multi-layer).
Electrical Characteristics (Unless otherwise specified, Ta=25°C, VCC=12V for 3.3V, 5V,
adjustable version and VCC=18V for the 12V version. ILOAD = 0.2A)
Characteristics
Quiescent Current
Symbol
Conditions
Min Typ Max Units
IQ VFB=12V force driver off
4
8
mA
VFB=1.3V
(Adjustable version only)
EN pin=5V
VCC=40V
-50
-100
200
300
Feedback bias current
IFB
-10
nA
Shutdown supply Current
ISD
100
uA
127 150 173
Oscillator frequency
FOSC
KHz
110
173
Oscillator frequency of short
circuit protect
(Adjustable) When VFB<0.5V
FSCP
60
60
KHz
KHz
(Fixed)When < VOUT*40%
Max. Duty Cycle (ON)
Min. Duty Cycle (OFF)
VFB=12V force driver on
DC
0
%
VFB=0V force driver off
100
Pear current, No outside circuit
V FB=0V force driver on
Current limit
ICL
3.5
-
A
%
V
Load Regulation( △VOUT/VOUT ) △VOUT IOUT = 0.2 to 3A
0.6 1.2
1.4
1.3
IOUT=3A, No outside circuit
VFB=0V force driver on
Saturation voltage
VSA T
1.5
No outside circuit
VFB=12V force driver off
SW pin
leakage
current
SW pin=0V
SW pin=-1V
-200 uA
ISW L
VCC=40V force driver off
-5
mA
VIL Low (regulator ON)
VIH High (regulator OFF)
IH VEN=2.5V (OFF)
-
0.6
EN pin logic input threshold
voltage
1.3
-0.1
V
2.0
-
EN pin logic input current
EN pin input current
-5
uA
IL
VEN=0.5V (ON)
-0.01 -1
135
Thermal shutdown Temp
TSD
℃
4/9
Advanced Power
Electronics Corp.
APE1706
150KHz, 3A PWM Buck DC/DC Converter
Electrical Characteristics (Continued)
version
Characteristics Symbol
Conditions
4.5V < VCC < 40V
0. 2A < ILOAD < 3A
Min
Typ
Max Units
Output Feedback
1.193
1.267
V
V
FB
1.23
APE1706-ADJ
voltage
VOUT programmed
/
1.180
/
1.280
for 3V
Efficiency
Output voltage
Efficiency
η
VCC = 12V, ILOAD=3A
4.75V < VCC < 40V
0.2A < ILOAD < 3A
VCC = 12V, ILOAD=3A
7V < VCC < 40V
74
3.3
75
%
V
3.168
3.432
V
OUT
APE1706-3.3V
APE1706-5.0V
APE1706-12V
/
3.135
/
3.465
η
%
4.80
5.20
V
Output voltage
Efficiency
V
OUT
5.0
80
12
89
0.2A < ILOAD < 3A
VCC = 12V, ILOAD=3A
15V < VCC < 40V
0.2A < ILOAD < 3A
VCC = 24V, ILOAD = 3A
/
4.75
/5.25
η
%
V
11.52
11.40
12.48
12.60
Output voltage
Efficiency
V
OUT
/
/
η
%
Specifications with boldface type are for full operating temperature range, the other type
are for TJ=25ºC.
5/9
Advanced Power
Electronics Corp.
APE1706
150KHz, 3A PWM Buck DC/DC Converter
Application Circuit
(1) Adjustable Output Voltage Version
VIN=12V
L1
Vout=5.0V/3A
1
2
33uH
U1
R1
4.7K
1
Vcc
2
3
SW
D1
B340A
Vss
4
C1
470uF
C2
0.1uF
C3
C6
FB
EN
R2
1.5K
470uF 0.1uF
5
APE1706
ON/OFF
(2) Adjustable Output Voltage Version With Delayed Startup
VIN=12V
L1
Vout=5.0V/3A
1
2
33uH
U1
Vcc
SW
FB
R1
C5
1nF
1
2
4
5
4.7K
C4
0.1uF
3
D1
B340A
Vss
C1
470uF
C2
0.1uF
C3
470uF
C6
0.1uF
R2
1.5K
EN
R3
100k
APE1706
ON/OFF
R1
R2
Vout = VFB
×
(1 +
)
VFB = 1.23V, R2 = 0.47K ~ 3K
VOUT
5.0V
3.3V
2.5V
R2
R1
1.8K
1.8K
1.8K
5.6K
3.0K
1.8K
(2) Fixed Output Voltage Version
VIN=12V
L1
27uH
Vout=3.3V/3A
1
2
U1
Vcc
SW
FB
1
2
3
D1
B340A
Vss
4
5
C1
470uF
C2
0.1uF
C3
C6
470uF 0.1uF
EN
APE1706-33
6/9
Advanced Power
Electronics Corp.
APE1706
150KHz, 3A PWM Buck DC/DC Converter
Function Descriptions
Pin Functions
Vcc
This is the positive input supply for the IC switching regulator. A suitable input
bypass capacitor must be presented at this pin to minimize voltage transients and to
supply the switching currents needed by the regulator.
Vss
Circuit ground.
SW
Internal switch. The voltage at this pin switches between (+VCC – VSAT) and
approximately – 0.5V, with a duty cycle of approximately VOUT / VCC. To minimize
coupling to sensitive circuitry, the PC board copper area connected to this pin should
be minimized.
Feedback
Senses the regulated output voltage to complete the feedback loop.
EN
Allows the switching regulator circuit to be shutdown using logic level signals thus
dropping the total input supply current to approximately 100uA. Pulling this pin below
a threshold voltage of approximately 1.3V turns the regulator on, and pulling this pin
above 1.3V (up to a maximum of Vcc) shuts the regulator down. If this shutdown
feature is not needed, the EN pin can be wired to the ground pin.
Thermal Considerations
The TO252-5L package needs a heat sink under most conditions. The size of the
heat sink depends on the input voltage, the output voltage, the load current and the
ambient temperature. The APE1706 junction temperature rises above ambient
temperature for a 3A load and different input and output voltages.
The data for these curves was taken with the APE1706 (TO252-5L package)
operating as a buck-switching regulator in an ambient temperature of 25
℃
(still air).
These temperature increments are all approximate and are affected by many factors.
Higher ambient temperatures requires more heat sinker.
7/9
Advanced Power
Electronics Corp.
APE1706
150KHz, 3A PWM Buck DC/DC Converter
Function Descriptions (Continued)
For the best thermal performance, wide copper traces and generous amounts of
printed circuit board copper (need connect to the VSS pins) should be used in the
board layout, (One exception is the SW(switch) pin, which should not have large
areas of copper.) Large areas of copper provide the best transfer of heat (lower
thermal resistance) to the surrounding air, and moving air lowers the thermal
resistance even further.
Package thermal resistance and junction temperature increments are all
approximate. The increments are affected by a lot of factors. Some of these factors
include board size, shape, thickness, position, location, and even board temperature.
Other factors are, trace width, total printed circuit copper area, copper thickness,
single or double-sided, multi-layer board and the amount of solder on the board.
The effectiveness of the PC board to dissipate heat also depends on the size,
quantity and spacing of other components on the board, as well as whether the
surrounding air is still or moving. Furthermore, some of these components such as the
catch diode will add heat to the PC board and the heat can vary as the input voltage
changes. For the inductor, depending on the physical size, type of core material and the
DC resistance, it could either act as a heat sink taking heat away from the board, or it
could add heat to the board.
8/9
Advanced Power
Electronics Corp.
APE1706
150KHz, 3A PWM Buck DC/DC Converter
Typical Characteristics
Output Ripple
Power on test wave
(VIN=12V, VOUT=5V, IOUT=3A)
(VIN=12V, VOUT=5V, IOUT=3A )
VOUT
VOUT (AC)
V
IN
SW
ISW
SW
ISW
Load Transient Response
EN on test wave
(VIN=12V, VOUT=5V, IOUT=0.2~3A)
(VIN=12V, VOUT=5V, IOUT=3A )
V
OUT (AC)
VOUT
V
IN
SW
SW
ISW
ISW
Efficiency
(VIN=12V, VOUT=5.0V)
Vin=12V
Efficiency
(VIN=24V, VOUT=5.0V)
Vin=12V
90%
90%
80%
70%
60%
50%
40%
30%
20%
10%
0%
80%
70%
60%
50%
40%
30%
20%
10%
0%
0.0
0.5
1.0
1.5
2.0
2.5
3.0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
Iout(A)
Iout(A)
9/9
ADVANCED POWER ELECTRONICS CORP.
Package Outline : TO-252(5L)
Millimeters
A
B
SYMBOLS
MIN
NOM MAX
A
B
C
D
P
6.40
5.2
6.6
5.35
6.80
5.50
7.20
2.80
6.80
2.20
7.00
2.50
1.27 REF.
0.65
S
0.50
3.50
0.40
2.20
0.45
0.80
4.50
0.60
2.40
0.55
E3
G
H
J
4.00
C
E3
0.50
M
2.30
0.50
K
L
0.00 0.075 0.15
0.90
5.40
1.20
5.60
1.50
5.80
M
D
S
P
1.All Dimensions Are in Millimeters.
2.Dimension Does Not Include Mold Protrusions.
H
K
J
L
Part Marking Information & Packing : TO-252(5L)
Part Number
Package Code
Outputvoltage
1706H-XX
LOGO
YWWSSS
Date Code (YWWSSS)
Y:Last Digit Of The Year
WW:Week
SSS:Sequence
相关型号:
APE1707M
IC SWITCHING REGULATOR, PDSO8, HALOGEN AND LEAD FREE, SOP-8, Switching Regulator or Controller
A-POWER
APE1707M-12
IC SWITCHING REGULATOR, PDSO8, HALOGEN AND LEAD FREE, SOP-8, Switching Regulator or Controller
A-POWER
APE1707M-33
IC SWITCHING REGULATOR, PDSO8, HALOGEN AND LEAD FREE, SOP-8, Switching Regulator or Controller
A-POWER
©2020 ICPDF网 联系我们和版权申明