APU8850Y5-HF [A-POWER]

IC VREG ADJUSTABLE POSITIVE LDO REGULATOR, PDSO5, HALOGEN FREE AND ROHS COMPLIANT, SOT-23, 5 PIN, Adjustable Positive Single Output LDO Regulator;
APU8850Y5-HF
型号: APU8850Y5-HF
厂家: ADVANCED POWER ELECTRONICS CORP.    ADVANCED POWER ELECTRONICS CORP.
描述:

IC VREG ADJUSTABLE POSITIVE LDO REGULATOR, PDSO5, HALOGEN FREE AND ROHS COMPLIANT, SOT-23, 5 PIN, Adjustable Positive Single Output LDO Regulator

光电二极管 输出元件 调节器
文件: 总6页 (文件大小:229K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
Advanced Power  
Electronics Corp.  
APU8850  
150mA ULTRA LOW DROPOUT POSITIVE  
ADJUSTABLE AND FIXED REGULATORS  
DESCRIPTION  
FEATURES  
The APU8850 device is an efficient linear voltage  
regulator with better than 2% initial voltage accuracy, very  
low dropout voltage and very low ground current designed  
especially for hand held, battery powered applications. Other  
features of the device are: TTL compatible enable/shutdown  
control input, current limiting and thermal shutdown.  
The APU8850 is available in fixed and adjustable  
Stable with 2.2uF Low ESR Ceramic Capacitor  
2% Voltage Reference Accuracy  
Wide Operating Range: 4.5V ~ 25V  
5uA Quiescent Current in Shutdown  
Current Limit and Thermal Shutdown  
Logic Input Enable Pin  
output voltage versions in a small SOT-23-5L, TSOT-23-5L,  
J-lead 2021-8, ESOP-8 & SOT-89 package.  
RoHS Compliant & Halogen Free  
SOT-89, ESOP-8, J-lead 2021-8, SOT-23-5L  
& TSOT-23-5L Package  
APPLICATIONS  
Laptop, Notebook & Palmtop Computers  
Battery Powered Equipments  
PCMCIA Vcc & Vpp Regulator  
Consumer Electronics  
High Efficiency Linear Power Supplies  
TYPICAL APPLICATION  
VOUT  
VIN  
VIN  
VOUT  
ADJ  
+
R1  
R2  
Vo= 1.25 x (1+R1/R2)  
+
C1  
2.2uF  
C2  
2.2uF  
GND  
EN  
Enable  
Figure 1 - Typical application of the APU8850 adjustable voltage regulator.  
VIN  
VIN  
VOUT  
CBYP  
VOUT=3.3V  
+
+
C1  
2.2uF  
C2  
2.2uF  
GND  
EN  
+ C3  
1000pF  
Enable  
Figure 2 - Typical application of the APU8850-33 fixed voltage regulator.  
ORDERING INFORMATION  
Halogen Free  
APU8850X-XX-HF  
Package  
Output Voltage  
Blank : ADJ  
15 : 1.5V  
18 : 1.8V  
25 : 2.5V  
28 : 2.8V  
30 : 3.0V  
33 : 3.3V  
50 : 5.0V  
Y5 : SOT-23-5L  
TY5 : TSOT-23-5L  
U : J-lead 2021-8  
G : SOT-89  
MP : ESOP-8  
Data and specifications subject to change without notice  
1
201104228  
Advanced Power  
Electronics Corp.  
ABSOLUTE MAXIMUM RATINGS (TA=25oC, unless otherwise specified.)  
APU8850  
Input Voltage (VIN) ------------------------------------------ 27V  
Enable Input Voltage (VEN) ------------------------------- 27V  
Storage Temperature Range (TST) --------------------- -65 to 150oC  
Operating Junction Temperature Range (TJ) -------- -40 to 85oC  
Thermal Resistance Junction to Ambient (Rthja)  
SOT-23-5L/TSOT-23-5L  
SOT-89  
256oC/W  
250oC/W  
150oC/W  
300oC/W  
ESOP-8  
J-lead 2021-8  
PACKAGE INFORMATION  
SOT-89  
ESOP-8 (MP) ADJ  
ESOP-8 (MP) Fixed  
Fixed  
ADJ  
TOP VIEW  
EN GND VIN  
( Top View )  
TAB is VIN  
(Top View)  
(Top View)  
TOP VIEW  
EN GND VIN  
1
8
1
8
VOUT  
VOUT  
VIN  
GND  
NC  
VIN  
GND  
NC  
2
3
4
7
6
5
2
3
4
7
6
5
NC  
NC  
NC  
CBYP  
NC  
SOT-23-5L  
SOT-23-5L  
GND  
GND  
TSOT-23-5L  
TSOT-23-5L  
1
2
3
ADJ  
EN  
EN  
VOUT  
CBYP  
ADJ  
VOUT  
J-lead 2021-8  
( Top View )  
GND VIN  
VOUT  
EN  
GND  
1
2
3
4
8
7
6
5
ADJ  
GND  
GND  
VOUT  
VIN  
GND  
ELECTRICAL SPECIFICATIONS  
Unless otherwise specified, these specifications apply over CIN=CO=2.2F, IO=100uA, VIN(MIN)=4.5V, CBYP=470pF  
(for fixed voltage devices), VEN=2V and TA=25oC. Typical values refer to TA=25oC. Low duty cycle pulse testing is used  
which keeps junction and case temperatures equal to the ambient temperature.  
UNITS  
%
Parameter  
SYM  
Vo  
TEST CONDITION  
MIN  
TYP MAX  
Reference Voltage  
Line Regulation  
-2  
-
0.1  
0.5  
1
2
VI  
VO + 2V<VIN<25V, IO=1mA  
VIN=VO+2V  
-
-
-
%/V  
%
VL  
Load Regulation (Note 1)  
-
IO=100uA  
-
-
VDROP  
Dropout Voltage (Note 2)  
V
IO=100mA  
-
1.2  
250  
1
-
IQ  
IQ(SD)  
IADJ  
ICL  
Ground Current (Note 3)  
Ground Current-SD Activated  
Adjust Pin Current  
VEN=2V, IO=100uA  
VEN=0V or Open  
VIN=4.5V, VO=VADJ  
-
-
uA  
uA  
uA  
mA  
mA  
V
-
-
-
0.1  
-
-
Current Limit  
200  
-
IZ  
VO=0V  
Short Current  
-
-
175  
-
-
Enable Pin Input LO Voltage  
Enable Pin Input HI Voltage  
Enable Pin Input LO Current  
Enable Pin Input HI Current  
Ripple Rejection  
VEN(L)  
VEN(H)  
Regulator OFF  
Regulator ON  
VEN(L) =0V  
0.8  
-
2
-
-
V
0.01  
10  
70  
150  
10  
-
uA  
uA  
dB  
oC  
oC  
V
EN(H)=2V  
-
-
PSRR  
CBYP=1nF, COUT=2.2uF, fRIPPLE = 1kHz  
-
-
Over Temperature Shutdown  
Over Temperature Shutdown Hysteresis  
-
-
-
-
Note 1: Low duty cycle pulse testing with Kelvin connections is required in order to maintain accurate data.  
Note 2: Dropout voltage is defined as the minimum differential voltage between VIN and VOUT required to maintain regulation at VOUT.  
It is measured when the output voltage drops 1% below its nominal value.  
Note 3: Ground current is the regulator quiescent current plus the pass transistor current. The total current from the supply is the sum  
of the load current plus the ground pin current.  
2
Advanced Power  
Electronics Corp.  
APU8850  
PIN DESCRIPTIONS  
PIN SYMBOL  
VIN  
PIN DESCRIPTION  
The input pin of the regulator. Typically a large storage capacitor is connected from  
this pin to ground to insure that the input voltage does not sag below the minimum  
drop out voltage during the load transient response. This pin must always be higher  
than VOUT by at least the amount of the dropout voltage and some margin in order  
for the device to regulate properly.  
Ground pin. This pin must be connected to the lowest potential in the system and  
all other pins must be at higher potential with respect to this pin.  
GND  
Enable pin. A low signal or left open on this pin shuts down the output. This pin  
must be tied HI or to VIN for normal operation.  
EN  
Adj (Adjustable only)  
A resistor divider from this pin to the VOUT pin and ground sets the output voltage.  
A 470 to 1000pF bypass capacitor connected to this pin reduces the output noise.  
The output of the regulator. A minimum of 2.2uF with max ESR of 1Ω capacitor  
must be connected from this pin to ground to insure stability.  
CBYP (Fixed only)  
VOUT  
BLOCK DIAGRAM  
VIN  
VOUT  
1
5
+
-
4
2
ADJ  
Thermal  
Shutdown  
+
Current  
Limit  
GND  
3
EN  
Figure 3 - APU8850Y5 Adjustable output block diagram.  
VIN  
VOUT  
1
5
+
-
4
2
CBYP  
GND  
+
Thermal  
Shutdown  
Current  
Limit  
3
EN  
Figure 4 - APU8850Y5 Fixed Mode output block diagram.  
3
Advanced Power  
Electronics Corp.  
APU8850  
TYPICAL PERFORMANCE CHARACTERISTICS  
VIN=5VVEN=5VVOUT=3.3V  
Output Voltage VS. Temperature  
3.37  
3.36  
3.35  
3.34  
3.33  
3.32  
3.31  
3.3  
Iout=0mA  
Iout=10mA  
Iout=20mA  
-40  
-20  
0
20  
40  
60  
80  
100  
Temperature(  
)
VIN=5VVEN=5VVOUT=3.3V  
ADJ Voltage VS. Temperature  
1.264  
1.26  
1.256  
1.252  
1.248  
1.244  
1.24  
Iout=0mA  
Iout=10mA  
Iout=20mA  
-40  
-20  
0
20  
40  
60  
80  
100  
Temperature(  
)
VIN=4.5V ,VOUT=3.3V IOUT=10mA~200mA  
Load Transient  
IOUT  
VOUT  
4
Advanced Power  
Electronics Corp.  
APU8850  
TYPICAL PERFORMANCE CHARACTERISTICS  
Quiescent Current vs. Temperature  
VIN=4.5V , VOUT=3.3V , IOUT=10mA  
Quiescent Current vs. Input Voltage  
VIN=4.5V~20V , VOUT=3.3V  
300  
350  
300  
250  
200  
150  
100  
50  
250  
200  
150  
100  
50  
0
0
4.5  
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
-40  
-20  
0
20  
40  
60  
80  
100  
125  
Temperature('C)  
Input Voltage(V)  
Output Voltage vs. Output Current  
Output Voltage vs. Input Voltage  
VIN=4.5V , VOUT=3.3V , IOUT=10mA~200mA  
VIN=4.5V~20V , VOUT=3.3V  
3.312  
3.32  
3.311  
3.31  
3.3  
3.31  
3.29  
3.309  
3.308  
3.307  
3.306  
3.28  
3.27  
3.26  
3.25  
Iout=0mA  
Iout=10mA  
Iout=20mA  
20  
40  
60  
80  
100  
120  
140  
160  
180  
200  
3.305  
4.5  
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
Output Current(mA)  
Input Voltage(V)  
Dropout Voltage vs. Temperature  
VIN=4.5V , VOUT=3.3V  
Dropout Voltage vs. Output Current  
VIN=4.5V , VOUT=3.3V , IOUT=10mA~200mA  
1.2  
0.9  
0.8  
1
0.7  
0.6  
0.5  
0.8  
0.6  
0.4  
0.4  
0.3  
0.2  
0.2  
0.1  
Iout=0mA  
Iout=10mA  
0
0
20  
40  
60  
80  
100  
120  
140  
160  
180  
200  
0
-40  
-20  
0
20  
40  
60  
80  
100  
125  
Output Current(mA)  
Temperature('C)  
5
Advanced Power  
Electronics Corp.  
APU8850  
MARKING INFORMATION  
ESOP-8  
Part Number  
Package Code  
Output Voltage :  
Identification  
Code  
Identification  
Code  
VOUT  
VOUT  
Blank  
15  
ADJ  
1.5V  
1.8V  
2.5V  
28  
2.8V  
3.0V  
3.3V  
5.0V  
8850MP-&&  
YWWSSS  
30  
18  
33  
25  
50  
Date Code (YWWSSS)  
YLast Digit Of The Year  
WWWeek  
SSSSequence  
SOT-23-5L / TSOT-23-5L  
Part Number : RZ  
Output Voltage :  
Identification  
Code  
Identification  
Code  
VOUT  
VOUT  
RZ&SS  
Blank  
ADJ  
1.5V  
1.8V  
2.5V  
G
H
I
2.8V  
3.0V  
3.3V  
5.0V  
C
D
F
Date Code  
J
SS:2004,2008,2012…  
SS:2003,2007,2011…  
SS:2002,2006,2010…  
SS:2001,2005,2009…  
J-lead 2021-8  
Part Number : RZ  
Output Voltage :  
Identification  
Code  
Identification  
Code  
VOUT  
VOUT  
Blank  
ADJ  
1.5V  
1.8V  
2.5V  
G
H
I
2.8V  
3.0V  
3.3V  
5.0V  
RZ&SS  
C
D
F
Date Code  
J
SS:2004,2008,2012…  
SS:2003,2007,2011…  
SS:2002,2006,2010…  
SS:2001,2005,2009…  
SOT-89  
Part Number  
Identification  
Code  
Identification  
Code  
Output Voltage :  
VOUT  
VOUT  
Blank  
ADJ  
1.5V  
1.8V  
2.5V  
G
H
I
2.8V  
3.0V  
3.3V  
5.0V  
8850&  
C
D
F
Date Code (YWWS)  
J
YWWS  
Y:Year  
WWWeek  
SSequence  
6

相关型号:

APU8852

150mA ULTRA LOW DROPOUT POSITIVE FIXED REGULATORS
A-POWER

APU8852Y5-28

IC VREG 2.8 V FIXED POSITIVE LDO REGULATOR, PDSO5, HALOGEN FREE AND ROHS COMPLIANT, SOT-23, 5 PIN, Fixed Positive Single Output LDO Regulator
A-POWER

APU8852Y5-30

IC VREG 3 V FIXED POSITIVE LDO REGULATOR, PDSO5, HALOGEN FREE AND ROHS COMPLIANT, SOT-23, 5 PIN, Fixed Positive Single Output LDO Regulator
A-POWER

APU8951

8-BIT MICRO CONTROLLER WITH 4/8KB FLASH EMBEDDED
APLUS

APU8951(40PDIP)

Microcontroller
APLUS

APU8951(44PLCC)

Microcontroller
APLUS

APU8951(44QFP)

Microcontroller
APLUS

APU8952

8-BIT MICRO CONTROLLER WITH 4/8KB FLASH EMBEDDED
APLUS

APU8952(40PDIP)

Microcontroller
APLUS

APU8952(44PLCC)

Microcontroller
APLUS

APU8952(44QFP)

Microcontroller
APLUS

APV

CERAMIC SMD CRYSTAL CLOCK OSCILLATOR
ABRACON