S-8223CAD-I6T1U [ABLIC]
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION);型号: | S-8223CAD-I6T1U |
厂家: | ABLIC |
描述: | BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION) |
文件: | 总30页 (文件大小:809K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
S-8223A/B/C/D Series
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK
(SECONDARY PROTECTION)
www.ablic.com
© ABLIC Inc., 2017-2018
Rev.1.3_00
The S-8223A/B/C/D Series is used for secondary protection of lithium-ion rechargeable batteries, and incorporates
high-accuracy voltage detection circuits and delay circuits.
Short-circuits between cells accommodate series connection of two cells or three cells.
The S-8223B/D Series limits its CO pin output voltage to 11.5 V max., so a FET with the gate withstand voltage of 12 V can be
used.
Features
• High-accuracy voltage detection circuit for each cell
Overcharge detection voltage n (n = 1 to 3)
3.600 V to 4.700 V (50 mV step)
Accuracy 20 mV (Ta = +25°C)
Accuracy 25 mV (Ta = −10°C to +60°C)
Overcharge hysteresis voltage n (n = 1 to 3)*1
0.0 mV to −550 mV (50 mV step)
−300 mV to −550 mV
−100 mV to −250 mV
−50 mV
Accuracy 20%
Accuracy 50 mV
Accuracy 25 mV
0.0 mV
Accuracy −25 mV to +20 mV
• Delay times for overcharge detection are generated only by an internal circuit (external capacitors are unnecessary)
Overcharge detection delay time is selectable:
Overcharge release delay time is selectable:
• Built-in timer reset delay circuit
1 s, 2 s, 4 s, 6 s, 8 s
2 ms, 64 ms
• Output form is selectable (S-8223A/C Series):
• Output logic is selectable (S-8223A/C Series):
CMOS output, Nch open-drain output
Active "H", active "L"
• CO pin output voltage is limited to 11.5 V max. (S-8223B/D Series)*2
• High-withstand voltage:
Absolute maximum rating 28 V
• Wide operation voltage range:
3.6 V to 28 V
• Wide operation temperature range:
• Low current consumption
Ta = −40°C to +85°C
During operation (VCU − 1.0 V for each cell):
During overdischarge (VCU × 0.5 V for each cell):
• Lead-free (Sn 100%), halogen-free
0.25 μA typ., 0.5 μA max. (Ta = +25°C)
0.3 μA max. (Ta = +25°C)
*1. Select the overcharge hysteresis voltage calculated as the following formula.
(Overcharge detection voltage n) + (Overcharge hysteresis voltage n) ≥ 3.4 V
*2. Only output logic active "H" is available.
Application
• Lithium-ion rechargeable battery packs (for secondary protection)
Package
• SNT-6A
1
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
S-8223A/B/C/D Series
Rev.1.3_00
Block Diagrams
1. S-8223A/C Series
1. 1 CMOS output product
VDD
VC1
Overcharge detection
comparator 1
+
−
VC2
VC3
VSS
Overcharge detection
comparator 2
Control logic
Delay circuit
Oscillator
+
−
CO
Overcharge detection
comparator 3
+
−
Figure 1
2
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
Rev.1.3_00
S-8223A/B/C/D Series
1. 2 Nch open-drain output product
VDD
VC1
Overcharge detection
comparator 1
+
−
VC2
VC3
VSS
Overcharge detection
comparator 2
Control logic
Delay circuit
Oscillator
+
−
CO
Overcharge detection
comparator 3
+
−
Figure 2
3
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
S-8223A/B/C/D Series
Rev.1.3_00
2. S-8223B/D Series
VDD
VC1
Overcharge detection
comparator 1
+
−
CO pin output voltage
limit circuit
VC2
VC3
VSS
Overcharge detection
comparator 2
Control logic
Delay circuit
Oscillator
+
−
CO
Overcharge detection
comparator 3
+
−
Figure 3
4
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
Rev.1.3_00
S-8223A/B/C/D Series
Product Name Structure
1. Product name
S-8223
x
xx
-
I6T1
U
Environmental code
U: Lead-free (Sn 100%), halogen-free
Package abbreviation and IC packing specifications*1
I6T1: SNT-6A, Tape
Serial code*2
Sequentially set from AA to AZ
Product type
A:
B:
C:
D:
Pin configuration 1, CMOS output, Nch open-drain output
Pin configuration 1, CO pin output voltage 11.5 V max.
Pin configuration 2, CMOS output, Nch open-drain output
Pin configuration 2, CO pin output voltage 11.5 V max.
*1. Refer to the tape drawing.
*2. Refer to "3. Product name list".
2. Package
Table 1 Package Drawing Codes
Package Name
SNT-6A
Dimension
PG006-A-P-SD
Tape
Reel
Land
PG006-A-C-SD
PG006-A-R-SD
PG006-A-L-SD
3. Product name list
3. 1 S-8223A Series
Table 2
Overcharge
Detection
Voltage
Overcharge
Hysteresis
Voltage
Overcharge
Overcharge
Release
Delay Time*2
[tCL
Detection
Product Name
Output Form*3
Output Logic*4
Delay Time*1
[VCU
]
[VHC
]
[tCU
6 s
6 s
6 s
6 s
6 s
6 s
6 s
4 s
4 s
4 s
]
]
S-8223AAA-I6T1U
S-8223AAB-I6T1U
S-8223AAC-I6T1U
S-8223AAD-I6T1U
S-8223AAE-I6T1U
S-8223AAF-I6T1U
S-8223AAG-I6T1U
S-8223AAH-I6T1U
S-8223AAI-I6T1U
S-8223AAJ-I6T1U
4.450 V
4.500 V
4.350 V
4.400 V
4.550 V
4.500 V
4.550 V
4.350 V
4.500 V
4.550 V
−400 mV
−400 mV
−400 mV
−400 mV
−400 mV
−400 mV
−400 mV
−400 mV
−400 mV
−400 mV
64 ms
64 ms
64 ms
64 ms
64 ms
2 ms
CMOS output
CMOS output
CMOS output
CMOS output
CMOS output
CMOS output
CMOS output
CMOS output
CMOS output
CMOS output
Active "H"
Active "H"
Active "H"
Active "H"
Active "H"
Active "H"
Active "H"
Active "H"
Active "H"
Active "H"
2 ms
64 ms
64 ms
64 ms
*1. Overcharge detection delay time 1 s / 2 s / 4 s / 6 s / 8 s is selectable.
*2. Overcharge release delay time 2 ms / 64 ms is selectable.
*3. Output form CMOS output / Nch open-drain output is selectable.
*4. Output logic active "H" / active "L" is selectable.
Remark Please contact our sales office for the products with detection voltage value other than those specified above.
5
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
S-8223A/B/C/D Series
Rev.1.3_00
3. 2 S-8223B Series
Table 3
Overcharge
Overcharge
Detection
Voltage
Overcharge
Hysteresis
Voltage
Overcharge Release
Delay Time*2
Detection
Product Name
Output Logic*3
Active "H"
Delay Time*1
[tCL
]
[VCU
]
[VHC
]
[tCU
]
S-8223BAA-I6T1U
4.500 V
−300 mV
4 s
2 ms
*1. Overcharge detection delay time 1 s / 2 s / 4 s / 6 s / 8 s is selectable.
*2. Overcharge release delay time 2 ms / 64 ms is selectable.
*3. Only output logic active "H" is available.
Remark Please contact our sales office for the products with detection voltage value other than those specified above.
3. 3 S-8223C Series
Table 4
Overcharge
Detection
Voltage
Overcharge
Hysteresis
Voltage
Overcharge
Detection
Overcharge
Release
Product Name
Output Form*3
Output Logic*4
Delay Time*1
Delay Time*2
[VCU
]
[VHC
]
[tCU
4 s
4 s
4 s
4 s
2 s
2 s
2 s
2 s
2 s
4 s
2 s
]
[tCL]
S-8223CAA-I6T1U
S-8223CAB-I6T1U
S-8223CAC-I6T1U
S-8223CAD-I6T1U
S-8223CAE-I6T1U
S-8223CAF-I6T1U
S-8223CAG-I6T1U
S-8223CAH-I6T1U
S-8223CAI-I6T1U
S-8223CAJ-I6T1U
S-8223CAK-I6T1U
−400 mV
−400 mV
−400 mV
−400 mV
−50 mV
4.400 V
4.450 V
4.500 V
4.350 V
4.250 V
4.150 V
4.350 V
4.450 V
4.500 V
4.300 V
4.200 V
2 ms
2 ms
2 ms
2 ms
2 ms
2 ms
2 ms
2 ms
2 ms
2 ms
2 ms
CMOS output
Active "H"
Active "H"
Active "H"
Active "H"
CMOS output
CMOS output
CMOS output
Nch open-drain output Active "H"
Nch open-drain output Active "H"
−50 mV
−400 mV
−400 mV
−400 mV
−400 mV
−400 mV
CMOS output
CMOS output
CMOS output
CMOS output
Active "H"
Active "H"
Active "H"
Active "H"
Nch open-drain output Active "H"
*1. Overcharge detection delay time 1 s / 2 s / 4 s / 6 s / 8 s is selectable.
*2. Overcharge release delay time 2 ms / 64 ms is selectable.
*3. Output form CMOS output / Nch open-drain output is selectable.
*4. Output logic active "H" / active "L" is selectable.
Remark Please contact our sales office for the products with detection voltage value other than those specified above.
6
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
Rev.1.3_00
S-8223A/B/C/D Series
Pin Configuration
1. SNT-6A
Top view
Table 5 S-8223A/B Series (Pin Configuration 1)
Pin No. Symbol
Description
1
2
3
6
5
4
1
VC1
Positive voltage connection pin of battery 1
Negative voltage connection pin of battery 1
Positive voltage connection pin of battery 2
Negative power supply input pin
Negative voltage connection pin of battery 3
Negative voltage connection pin of battery 2
Positive voltage connection pin of battery 3
Positive power supply input pin
2
VC2
Figure 4
3
4
VSS
VC3
5
6
VDD
CO
FET gate connection pin for charge control
Table 6 S-8223C/D Series (Pin Configuration 2)
Pin No. Symbol
Description
1
2
3
CO
FET gate connection pin for charge control
Positive power supply input pin
VDD
VC1
Positive voltage connection pin of battery 1
Negative voltage connection pin of battery 1
Positive voltage connection pin of battery 2
Negative voltage connection pin of battery 2
Positive voltage connection pin of battery 3
Negative power supply input pin
4
5
6
VC2
VC3
VSS
Negative voltage connection pin of battery 3
7
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
S-8223A/B/C/D Series
Rev.1.3_00
Absolute Maximum Ratings
Table 7
(Ta = +25°C unless otherwise specified)
Symbol Applied Pin Absolute Maximum Rating Unit
Item
Input voltage between VDD pin and VSS pin
VDS
VDD
VSS − 0.3 to VSS + 28
VSS − 0.3 to VSS + 28
VDD − 28 to VDD + 0.3
VSS − 0.3 to VDD + 0.3
VSS − 0.3 to VSS + 28
VSS − 0.3 to VDD + 0.3
−40 to +85
V
V
VC1
Input pin voltage
VIN
VC2, VC3
V
CMOS output
V
S-8223A/C Series
S-8223B/D Series
CO pin output
voltage
Nch open-drain output VCO
CO
V
V
Operation ambient temperature
Storage temperature
Topr
Tstg
−
−
°C
°C
−40 to +125
Caution The absolute maximum ratings are rated values exceeding which the product could suffer physical damage.
These values must therefore not be exceeded under any conditions.
Thermal Resistance Value
Table 8
Item
Symbol
Condition
Board A
Min.
−
−
−
−
Typ.
224
176
−
−
−
Max.
Unit
−
−
−
−
−
°C/W
°C/W
°C/W
°C/W
°C/W
Board B
Board C
Board D
Board E
Junction-to-ambient thermal resistance*1 θJA
SNT-6A
−
*1. Test environment: compliance with JEDEC STANDARD JESD51-2A
Remark Refer to " Power Dissipation" and "Test Board" for details.
8
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
Rev.1.3_00
S-8223A/B/C/D Series
Electrical Characteristics
Table 9
(Ta = +25°C unless otherwise specified)
Test
Circuit
Item
Symbol
Condition
Min.
Typ.
Max.
Unit
Detection Voltage
VCU
− 0.020
VCU
VCU
+ 0.020
VCU
Ta = +25°C
Ta = −10°C to +60°C*1
VCU
VCU
V
1
Overcharge detection voltage n
(n = 1, 2, 3)
VCUn
V
V
V
1
1
1
− 0.025
+ 0.025
−550 mV
−250 mV
≤
≤
VHC
VHC
≤
≤
−300 mV
−100 mV
VHC
×
1.2
VHC VHC × 0.8
VHC
− 0.050
VHC
− 0.025
VHC
VHC
+ 0.050
VHC
+ 0.025
VHC
VHC
VHC
VHC
Overcharge hysteresis voltage n
(n = 1, 2, 3)
VHCn
VHC = −50 mV
V
V
1
1
VHC = 0.0 mV
− 0.025
+ 0.020
Input Voltage
Operation voltage between
VDD pin and VSS pin
Output Voltage
−
VDSOP
3.6
5.0
−
28
V
V
−
CO pin output voltage "H"
Input Current
VCOH
S-8223B/D Series
8.0
11.5
1
Current consumption
during operation
IOPE
V1 = V2 = V3 = VCU − 1.0 V
V1 = V2 = V3 = VCU × 0.5 V
−
−
0.25
0.5
0.3
μA
μA
2
2
Current consumption
during overdischarge
VC1 pin input current
VCn pin input current (n = 2, 3)
Output Current
IOPED
−
IVC1
IVCn
V1 = V2 = V3 = VCU − 1.0 V
V1 = V2 = V3 = VCU − 1.0 V
−
−0.3
−
0
0.3
0.3
μA
μA
3
3
S-8223A/C Series
(CMOS output product),
S-8223B/D Series
−
S-8223A/C Series
(Nch open-drain output product)
CO pin source current
ICOH
−
−
−20
μA
4
CO pin sink current
CO pin leakage current
Delay Time
ICOL
20
−
−
−
μA
μA
4
4
ICOLL
−
0.1
Overcharge detection delay time tCU
−
tCU × 0.8
tCU
2.0
64
12
−
tCU × 1.2
3.0
s
1
1
1
1
1
t
CL = 2 ms
1.6
51.2
6
ms
ms
ms
ms
Overcharge release delay time tCL
tCL = 64 ms
76.8
20
Overcharge timer reset delay time tTR
Transition time to test mode tTST
−
−
−
10
*1. Since products are not screened at high and low temperature, the specification for this temperature range is guaranteed
by design, not tested in production.
9
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
S-8223A/B/C/D Series
Rev.1.3_00
Test Circuits
1. Overcharge detection voltage, overcharge hysteresis voltage (Test circuit 1)
Set SW1 to OFF in CMOS output product of the S-8223A/C Series and in the S-8223B/D Series, and set SW1 to ON in
Nch open-drain output product of the S-8223A/C Series.
1. 1 Overcharge detection voltage n (VCUn
)
Set V0 = 0 V, V1 = V2 = V3 = VCU − 0.05 V in test circuit 1. The overcharge detection voltage 1 (VCU1) is the V1
voltage when the CO pin output inverts after the V1 voltage has been gradually increased.
Overcharge detection voltage (VCUn) (n = 2 to 3) can be determined in the same way as when n = 1.
1. 2 Overcharge hysteresis voltage n (VHCn
)
Set V0 = 0 V, V1 = VCU + 0.05 V, V2 = V3 = 2.5 V. The overcharge hysteresis voltage 1 (VHC1) is the difference
between V1 voltage and VCU1 when the CO pin output inverts again after the V1 voltage has been gradually
decreased.
Overcharge hysteresis voltage (VHCn) (n = 2 to 3) can be determined in the same way as when n = 1.
2. Output voltage (S-8223B/D Series) (Test circuit 1)
Set SW1 to OFF in the S-8223B/D Series.
2. 1 CO pin output voltage "H"
The CO pin output voltage "H" (VCOH) is the voltage between the CO pin and the VSS pin when V0 = 0 V, V1 = V2
= V3 = 5.2 V.
3. Output current (Test circuit 4)
3. 1 CMOS output product in S-8223A/C Series
Set SW4 and SW5 to OFF.
3. 1. 1 Active "H"
(1) CO pin source current (ICOH
)
Set SW4 to ON after setting V1 = 5.2 V, V2 = 2.8 V, V3 = 2.5 V, V4 = 0.5 V. I1 is the CO pin source
current (ICOH) at that time.
(2) CO pin sink current (ICOL
)
Set SW5 to ON after setting V1 = V2 = V3 = 3.5 V, V5 = 0.5 V. I2 is the CO pin sink current (ICOL) at that
time.
3. 1. 2 Active "L"
(1) CO pin source current (ICOH
)
Set SW4 to ON after setting V1 = V2 = V3 = 3.5 V, V4 = 0.5 V. I1 is the CO pin source current (ICOH) at
that time.
(2) CO pin sink current (ICOL
)
Set SW5 to ON after setting V1 = 5.2 V, V2 = 2.8 V, V3 = 2.5 V, V4 = 0.5 V. I2 is the CO pin sink current
(ICOL) at that time.
10
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
Rev.1.3_00
S-8223A/B/C/D Series
3. 2 Nch open-drain output product in S-8223A/C Series
Set SW4 and SW5 to OFF.
3. 2. 1 Active "H"
(1) CO pin leakage current (ICOLL
)
Set SW5 to ON after setting V1 = 9.4 V, V2 = V3 = 9.3 V, V5 = 28 V. I2 is the CO pin leakage current
(ICOLL) at that time.
(2) CO pin sink current (ICOL
)
Set SW5 to ON after setting V1 = 5.2 V, V2 = 2.8 V, V3 = 2.5 V, V5 = 0 V. I2 is the CO pin sink current
(ICOL) at that time.
3. 2. 2 Active "L"
(1) CO pin leakage current (ICOLL
)
Set SW5 to ON after setting V1= V2 = V3 = 3.5 V, V5 = 28 V. I2 is the CO pin leakage current (ICOLL
at that time.
)
(2) CO pin sink current (ICOL
)
Set SW5 to ON after setting V1 = 5.2 V, V2 = 2.8 V, V3 = 2.5 V, V5 = 0 V. I2 is the CO pin sink current
(ICOL) at that time.
3. 3 S-8223B/D Series
Set SW4 and SW5 to OFF.
3. 3. 1 CO pin source current (ICOH
)
Set SW5 to ON after setting V1 = V2 = V3 = 3.5 V, V5 = VCOH − 0.5 V. I2 is the CO pin source current
(ICOH) at that time.
3. 3. 2 CO pin sink current (ICOL
)
Set SW5 to ON after setting V1 = V2 = V3 = 3.5 V, V5 = 0.5 V. I2 is the CO pin sink current (ICOL) at that
time.
4. Overcharge detection delay time (tCU), overcharge release delay time (tCL) (Test circuit 1)
Set SW1 to OFF in CMOS output product of the S-8223A/C Series and in the S-8223B/D Series, and set SW1 to ON in
Nch open-drain output product of the S-8223A/C Series.
Increase V1 up to 5.2 V after setting V0 = 0 V, V1 = V2 = V3 = 3.5 V. The overcharge detection delay time (tCU) is the time
period until the CO pin output inverts. After that, decrease V1 down to 3.5 V. The overcharge release delay time (tCL) is
the time period until the CO pin output inverts.
5. Overcharge timer reset delay time (tTR) (Test circuit 1)
Set SW1 to OFF in CMOS output product of the S-8223A/C Series and in the S-8223B/D Series, and set SW1 to ON in
Nch open-drain output product of the S-8223A/C Series.
Increase V1 up to 5.2 V (first rise), and decrease V1 down to 3.5 V within the overcharge detection delay time (tCU) after
setting V0 = 0 V, V1 = V2 = V3 = 3.5 V. After that, increase V1 up to 5.2 V again (second rise), and detect the time period
until the CO pin output inverts.
When the period from when V1 has fallen to the second rise is short, CO pin output inverts after tCU has elapsed since
the first rise. If the period is gradually made longer, CO pin output inverts after tCU has elapsed since the second rise.
The overcharge timer reset delay time (tTR) is the period from V1 fall until the second rise at that time.
11
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
S-8223A/B/C/D Series
Rev.1.3_00
6. Transition time to test mode (tTST) (Test circuit 1)
Set SW1 to OFF in CMOS output product of the S-8223A/C Series and in the S-8223B/D Series, and set SW1 to ON in
Nch open-drain output product of the S-8223A/C Series.
Increase V0 up to 4.0 V, and decrease V0 again to 0 V after setting V0 = 0 V, V1 = V2 = V3 = 3.5 V.
When the period from when V0 was raised to when it has fallen is short, if an overcharge detection operation is
performed subsequently, the overcharge detection delay time is tCU. However, when the period from when V0 is raised to
when it has fallen is gradually made longer, the delay time during the subsequent overcharge detection operation is
shorter than tCU. The transition time to test mode (tTST) is the period from when V0 was raised to when it has fallen at that
time.
12
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
Rev.1.3_00
S-8223A/B/C/D Series
100 kΩ
SW1
IOPE
IOPED
S-8223A/B/C/D Series
S-8223A/B/C/D Series
VDD
VC1
VC2
CO
VDD
VC1
VC2
CO
VSS
VC3
V0
V1
V2
V
A
VSS
V3
V1
V2
V3
VC3
Figure 5 Test Circuit 1
Figure 6 Test Circuit 2
V4
A
I1
SW4
S-8223A/B/C/D Series
S-8223A/B/C/D Series
VDD
VC1
VC2
CO
VSS
VC3
VDD
VC1
VC2
CO
VSS
VC3
IVC1
SW5
A
IVC2
V3
V1
V2
IVC3
A
V3
V1
V2
V
A
A
I2
V5
Figure 7 Test Circuit 3
Figure 8 Test Circuit 4
13
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
S-8223A/B/C/D Series
Rev.1.3_00
Operation
Remark Refer to " Battery Protection IC Connection Examples".
1. Normal status
If the voltage of each of the batteries is lower than "the overcharge detection voltage (VCU) + the overcharge hysteresis
voltage (VHC)", the CO pin output changes to "L" (active "H") or "H" (active "L"). This is called normal status.
2. Overcharge status
When the voltage of one of the batteries exceeds VCU during charging under normal conditions and the status is
retained for the overcharge detection delay time (tCU) or longer, CO pin output inverts. This status is called overcharge
status. Connecting a FET to the CO pin provides charge control and a second protection.
If the voltage of each of the batteries is lower than VCU + VHC and the status is retained for the overcharge release delay
time (tCL) or longer, S-8223A/B/C/D Series changes to normal status.
3. Overcharge timer reset function
When an overcharge release noise that forces the voltage of one of the batteries temporarily below VCU is input during
tCU from when VCU is exceeded to when charging is stopped, tCU is continuously counted if the time the overcharge
release noise persists is shorter than the overcharge timer reset delay time (tTR). Under the same conditions, if the time
the overcharge release noise persists is tTR or longer, counting of tCU is reset once. After that, when VCU has been
exceeded, counting tCU resumes.
14
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
Rev.1.3_00
S-8223A/B/C/D Series
4. Test mode
In the S-8223A/B/C/D Series, the overcharge detection delay time (tCU) can be shortened by entering the test mode.
The test mode can be set by retaining the VDD pin voltage 4.0 V or more higher than the VC1 pin voltage for at least
10 ms (V1 = V2 = V3 = 3.5 V, Ta = +25 °C). The status is retained by the internal latch and the test mode is retained
even if the VDD pin voltage is decreased to the same voltage as that of the VC1 pin.
If the CO pin becomes detection status when the delay time has elapsed after overcharge detection, the latch for
retaining the test mode is reset and the S-8223A/B/C/D Series exits from the test mode.
VDD pin voltage
VC1 pin voltage
4.0 V or
higher
Pin voltage
VHCn
VCUn
Battery voltage
(n = 1 to 3)
Test mode
tTST = 10 ms max.
CO pin
(Active "H")
CO pin
(Active "L")
32 ms typ.
Caution 1. Set the test mode when no batteries are overcharged.
tCL
2. The overcharge timer reset delay time (tTR) is not shortened in the test mode.
Figure 9
15
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
S-8223A/B/C/D Series
Rev.1.3_00
Timing Charts
1. Overcharge detection operation
VHCn
VCUn
Battery voltage
(n = 1 to 3)
tTR or longer tTR or shorter
t
CU or shorter
CO pin
(Active "H")
CO pin
(Active "L")
tCU
tCL
Figure 10
16
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
Rev.1.3_00
S-8223A/B/C/D Series
2. Overcharge timer reset operation
VHCn
tTR or shorter
t
TR or longer
tTR or shorter
VCUn
Battery voltage
(n = 1 to 3)
tCU or
shorter
tTR
CO pin
(Active "H")
Timer reset
tCU
CO pin
(Active "L")
Figure 11
17
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
S-8223A/B/C/D Series
Rev.1.3_00
Battery Protection IC Connection Examples
1. 3-serial cell
SCP
EB+
VDD
RVDD
CVDD
VC1
R1
C1
C2
C3
BAT1
BAT2
BAT3
VC2
S-8223A/B/C/D
Series
R2
R3
FET*1
DP
VC3
CO
VSS
EB−
*1. The S-8223B/D Series limits its CO pin output voltage to 11.5 V max., so a FET with the gate withstand voltage
of 12 V can be used.
Figure 12
Table 10 Constants for External Components
No.
1
Part
R1 to R3
Min.
0.1
Typ.
1
Max.
10
Unit
kΩ
μF
Ω
0.01
100
2
C1 to C3, CVDD
RVDD
0.1
330
1
3
1000
Caution 1. The above constants are subject to change without prior notice.
2. It has not been confirmed whether the operation is normal or not in circuits other than the above
example of connection. In addition, the example of connection shown above and the constant
will not guarantee successful operation. Perform thorough evaluation using the actual
application to set the constant.
3. Set the same constants to R1 to R3, and to C1 to C3 and CVDD
.
4. Since the CO pin may become detection status transiently when the battery is being connected,
be sure to connect the positive terminal of BAT1 last in order to prevent the protection fuse from
cutoff.
18
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
Rev.1.3_00
S-8223A/B/C/D Series
2. 2-serial cell
SCP
EB+
VDD
VC1
VC2
RVDD
CVDD
R1
BAT1
BAT2
C1
R2
S-8223A/B/C/D
Series
C2
FET
DP
VC3
VSS
CO
EB−
Figure 13
Table 11 Constants for External Components
No.
1
Part
R1, R2
Min.
0.1
Typ.
1
Max.
10
Unit
kΩ
μF
Ω
0.01
100
0.1
330
1
2
C1, C2, CVDD
RVDD
1000
3
Caution 1. The above constants are subject to change without prior notice.
2. It has not been confirmed whether the operation is normal or not in circuits other than the above
example of connection. In addition, the example of connection shown above and the constant
will not guarantee successful operation. Perform thorough evaluation using the actual
application to set the constant.
3. Set the same constants to R1, R2, and to C1, C2 and CVDD
.
4. Since the CO pin may become detection status transiently when the battery is being connected,
be sure to connect the positive terminal of BAT1 last in order to prevent the protection fuse from
cutoff.
19
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
S-8223A/B/C/D Series
Rev.1.3_00
[For SCP, contact]
Global Sales & Marketing Division, Dexerials Corporation
Gate City Osaki East Tower 8F, 1-11-2
Osaki, Shinagawa-ku, Tokyo, 141-0032, Japan
TEL +81-3-5435-3946
Contact Us: http://www.dexerials.jp/en/
Precaution
• Do not connect batteries charged with VCU + VHC or higher.
• If the connected batteries include a battery charged with VCU + VHC or higher, the S-8223A/B/C/D Series may become
overcharge status after all pins are connected.
• In some application circuits, even if an overcharged battery is not included, the order of connecting batteries may be
restricted to prevent transient output of the CO pin detection pulses when the batteries are connected. Perform
thorough evaluation with the actual application circuit.
• Before the battery connection, short-circuit the battery side pins RVDD and R1, shown in the figures in " Battery
Protection IC Connection Examples".
• The application conditions for the input voltage, output voltage, and load current should not exceed the power
dissipation.
• Do not apply to this IC an electrostatic discharge that exceeds the performance ratings of the built-in electrostatic
protection circuit.
• ABLIC Inc. claims no responsibility for any disputes arising out of or in connection with any infringement of patents
owned by a third party by products including this IC.
20
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
Rev.1.3_00
S-8223A/B/C/D Series
Characteristics (Typical Data)
1. Detection voltage
1. 1 VCU vs. Ta
1. 2 VCU + VHC vs. Ta
VCU = 4.500 V
VHC = −400 mV
4.520
4.510
4.500
4.490
4.480
4.200
4.150
4.100
4.050
4.000
−40 −25
0
25
50
75 85
−40 −25
0
25
50
75 85
Ta [°C]
Ta [°C]
2. Current consumption
2. 1 IOPE vs. Ta
2. 2 IOPED vs. Ta
VDD = 10.5 V
VDD = 6.75 V
0.5
0.4
0.3
0.2
0.1
0.0
0.3
0.2
0.1
0.0
−40 −25
0
25
50
75 85
−40 −25
0
25
50
75 85
Ta [°C]
Ta [°C]
2. 3 IOPE vs. VDD
Ta = +25°C
80
60
40
20
0
0
5
10
15
20
25
30
V
DD [V]
3. Delay time
3. 1 tCU vs. Ta
VDD = 12.2 V
8.0
6.0
4.0
2.0
0.0
−40 −25
0
25
Ta [°C]
50
75 85
21
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
S-8223A/B/C/D Series
Rev.1.3_00
4. Output current
4. 1 ICOH vs. VDD (S-8223A/C Series)
4. 2 ICOH vs. VDD (S-8223B/D Series)
Ta = +25°C
Ta = +25°C
80
100
120
140
160
180
200
10
20
30
40
50
0
5
10
15
20
25
30
0
5
10
15
20
25
30
V
DD [V]
VDD [V]
4. 3 ICOL vs. VDD
4. 4 ICOLL vs. VDD
Ta = +25°C
Ta = +25°C
100
80
60
40
20
0
0.10
0.08
0.06
0.04
0.02
0.00
0
0
5
10
15
20
25
30
5
10
15
20
25
30
V
DD [V]
VDD [V]
5. Output voltage
5. 1 VCOH vs. VDD
12
10
8
6
4
2
0
0
5
10
15
20
25
30
V
DD [V]
22
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
Rev.1.3_00
S-8223A/B/C/D Series
Marking Specifications
1. SNT-6A
Top view
(1) to (3):
(4) to (6):
Product code (refer to Product name vs. Product code)
Lot number
6
5
4
(1) (2) (3)
(4) (5) (6)
1
2
3
Product name vs. Product code
1. 1 S-8223A Series
1. 3 S-8223C Series
Product code
Product code
Product name
Product name
(1)
(2)
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
(3)
A
D
E
F
G
H
I
(1)
5
5
5
5
5
5
5
5
5
5
5
(2)
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
(3)
M
N
O
P
S-8223CAA-I6T1U
S-8223CAB-I6T1U
S-8223CAC-I6T1U
S-8223CAD-I6T1U
S-8223CAE-I6T1U
S-8223CAF-I6T1U
S-8223CAG-I6T1U
S-8223CAH-I6T1U
S-8223CAI-I6T1U
S-8223CAJ-I6T1U
S-8223CAK-I6T1U
S-8223AAA-I6T1U
S-8223AAB-I6T1U
S-8223AAC-I6T1U
S-8223AAD-I6T1U
S-8223AAE-I6T1U
S-8223AAF-I6T1U
S-8223AAG-I6T1U
S-8223AAH-I6T1U
S-8223AAI-I6T1U
S-8223AAJ-I6T1U
5
5
5
5
5
5
5
5
5
5
Q
R
S
J
T
K
L
U
V
X
1. 2 S-8223B Series
Product name
Product code
(1)
5
(2)
Q
(3)
W
S-8223BAA-I6T1U
23
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
S-8223A/B/C/D Series
Rev.1.3_00
Power Dissipation
SNT-6A
Tj = +125°C max.
1.0
0.8
B
0.6
A
0.4
0.2
0.0
0
25
50
75
100 125 150 175
Ambient temperature (Ta) [°C]
Board
Power Dissipation (PD)
A
B
C
D
E
0.45 W
0.57 W
−
−
−
24
SNT-6A Test Board
No. SNT6A-A-Board-SD-1.0
ABLIC Inc.
1.57±0.03
6
5
4
+0.05
-0.02
0.08
1
2
3
0.5
0.48±0.02
0.2±0.05
No. PG006-A-P-SD-2.1
SNT-6A-A-PKG Dimensions
PG006-A-P-SD-2.1
TITLE
No.
ANGLE
UNIT
mm
ABLIC Inc.
+0.1
-0
ø1.5
4.0±0.1
2.0±0.05
0.25±0.05
+0.1
ø0.5
-0
4.0±0.1
0.65±0.05
1.85±0.05
3
2
5
1
6
4
Feed direction
No. PG006-A-C-SD-2.0
TITLE
SNT-6A-A-Carrier Tape
PG006-A-C-SD-2.0
No.
ANGLE
UNIT
mm
ABLIC Inc.
12.5max.
9.0±0.3
Enlarged drawing in the central part
ø13±0.2
(60°)
(60°)
No. PG006-A-R-SD-1.0
SNT-6A-A-Reel
TITLE
No.
PG006-A-R-SD-1.0
ANGLE
UNIT
5,000
QTY.
mm
ABLIC Inc.
0.52
2
1.36
0.52
1
0.3
0.2
1.
2.
(0.25 mm min. / 0.30 mm typ.)
(1.30 mm ~ 1.40 mm)
0.03 mm
SNT
1. Pay attention to the land pattern width (0.25 mm min. / 0.30 mm typ.).
2. Do not widen the land pattern to the center of the package ( 1.30 mm ~ 1.40 mm ).
Caution 1. Do not do silkscreen printing and solder printing under the mold resin of the package.
2. The thickness of the solder resist on the wire pattern under the package should be 0.03 mm
or less from the land pattern surface.
3. Match the mask aperture size and aperture position with the land pattern.
4. Refer to "SNT Package User's Guide" for details.
(0.25 mm min. / 0.30 mm typ.)
(1.30 mm ~ 1.40 mm)
1.
2.
SNT-6A-A
-Land Recommendation
TITLE
No. PG006-A-L-SD-4.1
No.
PG006-A-L-SD-4.1
ANGLE
UNIT
mm
ABLIC Inc.
Disclaimers (Handling Precautions)
1. All the information described herein (product data, specifications, figures, tables, programs, algorithms and
application circuit examples, etc.) is current as of publishing date of this document and is subject to change without
notice.
2. The circuit examples and the usages described herein are for reference only, and do not guarantee the success of
any specific mass-production design.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by the reasons other than the products
described herein (hereinafter "the products") or infringement of third-party intellectual property right and any other
right due to the use of the information described herein.
3. ABLIC Inc. is not liable for any losses, damages, claims or demands caused by the incorrect information described
herein.
4. Be careful to use the products within their ranges described herein. Pay special attention for use to the absolute
maximum ratings, operation voltage range and electrical characteristics, etc.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by failures and / or accidents, etc. due to
the use of the products outside their specified ranges.
5. Before using the products, confirm their applications, and the laws and regulations of the region or country where they
are used and verify suitability, safety and other factors for the intended use.
6. When exporting the products, comply with the Foreign Exchange and Foreign Trade Act and all other export-related
laws, and follow the required procedures.
7. The products are strictly prohibited from using, providing or exporting for the purposes of the development of
weapons of mass destruction or military use. ABLIC Inc. is not liable for any losses, damages, claims or demands
caused by any provision or export to the person or entity who intends to develop, manufacture, use or store nuclear,
biological or chemical weapons or missiles, or use any other military purposes.
8. The products are not designed to be used as part of any device or equipment that may affect the human body, human
life, or assets (such as medical equipment, disaster prevention systems, security systems, combustion control
systems, infrastructure control systems, vehicle equipment, traffic systems, in-vehicle equipment, aviation equipment,
aerospace equipment, and nuclear-related equipment), excluding when specified for in-vehicle use or other uses by
ABLIC, Inc. Do not apply the products to the above listed devices and equipments.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by unauthorized or unspecified use of
the products.
9. In general, semiconductor products may fail or malfunction with some probability. The user of the products should
therefore take responsibility to give thorough consideration to safety design including redundancy, fire spread
prevention measures, and malfunction prevention to prevent accidents causing injury or death, fires and social
damage, etc. that may ensue from the products' failure or malfunction.
The entire system in which the products are used must be sufficiently evaluated and judged whether the products are
allowed to apply for the system on customer's own responsibility.
10. The products are not designed to be radiation-proof. The necessary radiation measures should be taken in the
product design by the customer depending on the intended use.
11. The products do not affect human health under normal use. However, they contain chemical substances and heavy
metals and should therefore not be put in the mouth. The fracture surfaces of wafers and chips may be sharp. Be
careful when handling these with the bare hands to prevent injuries, etc.
12. When disposing of the products, comply with the laws and ordinances of the country or region where they are used.
13. The information described herein contains copyright information and know-how of ABLIC Inc. The information
described herein does not convey any license under any intellectual property rights or any other rights belonging to
ABLIC Inc. or a third party. Reproduction or copying of the information from this document or any part of this
document described herein for the purpose of disclosing it to a third-party is strictly prohibited without the express
permission of ABLIC Inc.
14. For more details on the information described herein or any other questions, please contact ABLIC Inc.'s sales
representative.
15. This Disclaimers have been delivered in a text using the Japanese language, which text, despite any translations into
the English language and the Chinese language, shall be controlling.
2.4-2019.07
www.ablic.com
相关型号:
S-8223CAE-I6T1U
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
ABLIC
S-8223CAF-I6T1U
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
ABLIC
S-8223CAG-I6T1U
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
ABLIC
S-8223CAH-I6T1U
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
ABLIC
S-8223CAI-I6T1U
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
ABLIC
S-8223CAJ-I6T1U
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
ABLIC
S-8223CAK-I6T1U
BATTERY PROTECTION IC FOR 2-SERIAL / 3-SERIAL CELL PACK (SECONDARY PROTECTION)
ABLIC
©2020 ICPDF网 联系我们和版权申明