AD5228BUJZ50-RL7 [ADI]
32-Position Manual Up/Down Control Potentiometer; 32位手动上/下控制电位器型号: | AD5228BUJZ50-RL7 |
厂家: | ADI |
描述: | 32-Position Manual Up/Down Control Potentiometer |
文件: | 总20页 (文件大小:341K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
32-Position Manual Up/Down Control
Potentiometer
AD5228
FUNCTIONAL BLOCK DIAGRAM
FEATURES
32-position digital potentiometer
10 kΩ, 50 kΩ, 100 kΩ end-to-end terminal resistance
Simple manual up/down control
Self-contained, requires only 2 pushbutton tactile switches
Built-in adaptive debouncer
Discrete step-up/step-down control
D
AD5228
UP/DOWN
E
CONTROL
LOGIC
V
DD
C
O
D
E
A
R1 R2
W
B
DISCRETE
STEP/AUTO
SCAN DETECT
Autoscan up/down control with 4 steps per second
Pin-selectable zero-scale/midscale preset
Low potentiometer mode tempco, 5 ppm/°C
Low rheostat mode tempco, 35 ppm/°C
Digital control compatible
PUSH-UP
BUTTON
PU
PD
ADAPTIVE
DEBOUNCER
ZERO- OR MID-
SCALE PRESET
PUSH-DOWN
BUTTON
PRE
GND
Ultralow power, IDD = 0.4 µA typ and 3 µA max
Low operating voltage, 2.7 V to 5.5 V
Automotive temperature range, −40°C to +105°C
Compact thin SOT-23-8 (2.9 mm × 3 mm) Pb-free package
Figure 1.
The AD5228 can increment or decrement the resistance in
discrete steps or in autoscan mode. When the or button
PU PD
is pressed briefly (no longer than 0.6 s), the resistance of the
AD5228 changes by one step. When the or button is held
APPLICATIONS
Mechanical potentiometer and trimmer replacements
LCD backlight, contrast, and brightness controls
Digital volume control
Portable device-level adjustments
Electronic front panel-level controls
Programmable power supply
PU PD
continuously for more than a second, the device activates the
autoscan mode and changes four resistance steps per second.
The AD5228 can also be controlled digitally; its up/down
features simplify microcontroller usage. The AD5228 is available
in a compact thin SOT-23-8 (TSOT-8) package. The part is
guaranteed to operate over the automotive temperature range of
−40°C to +105°C.
GENERAL DESCRIPTION
The AD5228 is Analog Devices’ latest 32-step-up/step-down
control digital potentiometer emulating mechanical potenti-
ometer operation1. Its simple up/down control interface allows
manual control with just two external pushbutton tactile
switches. The AD5228 is designed with a built-in adaptive
debouncer that ignores invalid bounces due to contact bounce
commonly found in mechanical switches. The debouncer is
adaptive, accommodating a variety of pushbutton tactile
switches that generally have less than 10 ms of bounce time
during contact closures. When choosing the switch, the user
should consult the timing specification of the switch to ensure
its suitability in an AD5228 application.
The AD5228’s simple interface, small footprint, and very low
cost enable it to replace mechanical potentiometers and
trimmers with typically 3× improved resolution, solid-state
reliability, and faster adjustment, resulting in considerable cost
saving in end users’ systems.
Users who consider EEMEM potentiometers should refer to the
recommendations in the Applications section.
Table 1. Truth Table
PU
PD
Operation1
0
0
1
1
0
1
0
1
RWB Decrement
RWB Increment
RWB Decrement
RWB Does Not Change
1RWA increments if RWB decrements and vice versa.
1 The terms digital potentiometer and RDAC are used interchangeably.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.326.8703
www.analog.com
© 2004 Analog Devices, Inc. All rights reserved.
AD5228
TABLE OF CONTENTS
Electrical Characteristics ................................................................. 3
Power-Up and Power-Down Sequences.................................. 14
Layout and Power Supply Biasing............................................ 14
Applications..................................................................................... 15
Manual Adjustable LED Driver................................................ 15
Adjustable Current Source for LED Driver ............................ 15
Automatic LCD Panel Backlight Control................................ 16
Audio Amplifier with Volume Control ................................... 16
Constant Bias with Supply to Retain Resistance Setting...... 17
Outline Dimensions....................................................................... 18
Ordering Guide .......................................................................... 18
Interface Timing Diagrams......................................................... 4
Absolute Maximum Ratings............................................................ 5
ESD Caution.................................................................................. 5
Pin Configuration and Function Descriptions............................. 6
Typical Performance Characteristics ............................................. 7
Theory of Operation ...................................................................... 11
Programming the Digital Potentiometers............................... 12
Controlling Inputs...................................................................... 13
Terminal Voltage Operation Range.......................................... 13
REVISION HISTORY
Revision 0: Initial Version
Rev. 0 | Page 2 of 20
AD5228
ELECTRICAL CHARACTERISTICS
10 kΩ, 50 kΩ, 100 kΩ versions: VDD = 3 V 10% or 5 V 10%, VA = VDD, VB = 0 V, −40°C < TA < +105°C, unless otherwise noted.
Table 2.
Parameter
Symbol
Conditions
Min Typ1
Max Unit
DC CHARACTERISTICS, RHEOSTAT MODE
Resistor Differential Nonlinearity2
Resistor Integral Nonlinearity2
Nominal Resistor Tolerance3
Resistance Temperature Coefficient
Wiper Resistance
R-DNL
RWB, A terminal = no connect
RWB, A terminal = no connect
−0.5
−0.5
−20
0.05 +0.5 LSB
0.1 +0.5 LSB
R-INL
∆RAB/RAB
(∆RAB/RAB) × 104/∆T
+20
%
35
ppm/°C
RW
VDD = 2.7 V
VDD = 5.5 V
100
50
200
Ω
Ω
DC CHARACTERISTICS, POTENTIOMETER DIVIDER MODE
(Specifications apply to all RDACs)
Resolution
N
5
Bits
Integral Nonlinearity3
Differential Nonlinearity3, 5
Voltage Divider Temperature Coefficient
Full-Scale Error
INL
−0.5
−0.5
0.05 +0.5 LSB
0.05 +0.5 LSB
DNL
(∆VW/VW) × 104/∆T
Midscale
5
ppm/°C
LSB
VWFSE
VWZSE
≥+15 steps from midscale
≤−16 steps from midscale
−1
0
−0.5
0.3
0
Zero-Scale Error
0.5
LSB
RESISTOR TERMINALS
Voltage Range6
Capacitance4 A, B
Capacitance4 W
VA, B, W
CA, B
CW
With respect to GND
f = 1 MHz, measured to GND
f = 1 MHz, measured to GND
VA = VB = VW
0
VDD
V
140
150
1
pF
pF
nA
Common-Mode Leakage
PU, PD INPUTS
ICM
Input High
VIH
VIL
II
VDD = 5 V
2.4
0
5.5
0.8
1
V
Input Low
VDD = 5 V
V
Input Current
VIN = 0 V or 5 V
µA
pF
Input Capacitance4
POWER SUPPLIES
Power Supply Range
Supply Standby Current
Supply Active Current7
Power Dissipation7, 8
CI
5
VDD
VDD = 5 V, PU = PD = VDD
2.7
5.5
3
V
IDD_STBY
IDD_ACT
PDISS
0.4
50
µA
µA
µW
VDD = 5 V, PU or PD = 0 V
VDD = 5 V
110
17
Power Supply Sensitivity
PSSR
VDD = 5 V 10%
0.01
0.05 %/%
Footnotes on next page.
Rev. 0 | Page 3 of 20
AD5228
Parameter
Symbol
Conditions
Min Typ1
Max Unit
DYNAMIC CHARACTERISTICS 4, 9, 10, 11
Built-in Debounce and Settling Time 12
PU Low Pulse Width
tDB
tPU
6
ms
ms
ms
µs
12
12
1
PD Low Pulse Width
tPD
PU High Repetitive Pulse Width
PD High Repetitive Pulse Width
Autoscan Start Time
tPU_REP
tPD_REP
tAS_START
tAS
1
µs
PU or PD = 0 V
0.6
0.8
1.2
s
Autoscan Time
PU or PD = 0 V
0.16 0.25
0.38
s
Bandwidth –3 dB
BW_10
BW_50
BW_100
THD
RAB = 10 kΩ, midscale
RAB = 50 kΩ, midscale
RAB = 100 kΩ, midscale
VA = 1 V rms, RAB = 10 kΩ,
VB = 0 V dc, f = 1 kHz
460
100
50
kHz
kHz
kHz
%
Total Harmonic Distortion
Resistor Noise Voltage
0.05
eN_WB
RWB = 5 kΩ, f = 1 kHz
14
nV/√Hz
1 Typicals represent average readings at 25°C, VDD = 5 V.
2 Resistor position nonlinearity error, R-INL, is the deviation from an ideal value measured between the maximum resistance and the minimum resistance wiper
positions. R-DNL measures the relative step change from ideal between successive tap positions. Parts are guaranteed monotonic.
3 INL and DNL are measured at VW with the RDAC configured as a potentiometer divider similar to a voltage output D/A converter. VA = VDD and VB = 0 V.
4 Guaranteed by design and not subject to production test.
5 DNL specification limits of 1 LSB maximum are guaranteed monotonic operating conditions.
6 Resistor Terminals A, B, and W have no limitations on polarity with respect to each other.
7 PU
PD
PU PD
or
and
have 100 kΩ internal pull-up resistors, IDD_ACT = VDD/100 kΩ + IOSC (internal oscillator operating current) when
is connected to ground.
8
PU PD
or
PDISS is calculated based on IDD_STBY × VDD only. IDD_ACT duration should be short. Users should not hold
dissipation.
pin to ground longer than necessary to elevate power
9 Bandwidth, noise, and settling time are dependent on the terminal resistance value chosen. The lowest R value results in the fastest settling time and highest
bandwidth. The highest R value results in the minimum overall power consumption.
10 All dynamic characteristics use VDD = 5 V.
11 Note that all input control voltages are specified with tR = tF = 1 ns (10% to 90% of VDD) and timed from a voltage level of 1.6 V. Switching characteristics are measured
using VDD = 5 V.
12
PU
The debouncer keeps monitoring the logic-low level once
is connected to ground. Once the signal lasts longer than 11 ms, the debouncer assumes the last
PU
bounce is met and allows the AD5228 to increment by one step. If the
PD
signal remains at low and reaches tAS_START, the AD5528 increments again, see Figure 7. Similar
characteristics apply to
operation.
INTERFACE TIMING DIAGRAMS
tPD
tPU
PU
tPU_REP
PU
tPD_REP
tDB
tDB
R
R
WB
WB
Figure 2. Increment RWB in Discrete Steps
Figure 4. Decrement RWB in Discrete Steps
PD
WB
PU
WB
tAS_START
tAS
tDB
tAS_START
tAS
R
R
tDB
Figure 5. Decrement RWB in Autoscan Mode
Figure 3. Increment RWB in Autoscan Mode
Rev. 0 | Page 4 of 20
AD5228
ABSOLUTE MAXIMUM RATINGS
Table 3.
Parameter
Rating
VDD to GND
VA, VB, VW to GND
−0.3 V, +7 V
0 V, VDD
PU, PD, PRE Voltage to GND
Maximum Current
0 V, VDD
IWB, IWA Pulsed
IWB Continuous (RWB ≤ 5 kΩ, A open)1
IWA Continuous (RWA ≤ 5 kΩ, B open)1
20 mA
1 mA
1 mA
500 µA/ 100 µA/
50 µA
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only and functional operation of the device at these or
any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
IAB Continuous
(RAB = 10 kΩ/50 kΩ/100 kΩ)1
Operating Temperature Range
Maximum Junction Temperature
(TJmax)
Storage Temperature
Lead Temperature
−40°C to +105°C
150°C
−65°C to +150°C
245°C
(Soldering, 10 s – 30 s)
Thermal Resistance2 θJA
230°C/W
1 Maximum terminal current is bounded by the maximum applied voltage
across any two of the A, B, and W terminals at a given resistance, the
maximum current handling of the switches, and the maximum power
dissipation of the package. VDD = 5 V.
2 Package power dissipation = (TJmax – TA) / θJA.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 5 of 20
AD5228
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
PU
PD
1
2
3
4
8
7
6
5
V
DD
PRE
B
AD5228
A
GND
W
Figure 6. SOT-23-8 Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
Mnemonic Description
1
PU
Push-Up Pin.
Connect to the external pushbutton. Active low. A 100 kΩ pull-up resistor is connected to VDD
.
2
PD
Push-Down Pin.
Connect to the external pushbutton. Active low. A 100 kΩ pull-up resistor is connected to VDD
.
3
4
5
6
7
A
GND
W
B
PRE
Resistor Terminal A. GND ≤VA ≤ VDD
Common Ground.
.
Wiper Terminal W. GND ≤ VW ≤ VDD
.
Resistor Terminal B. GND ≤ VB ≤ VDD
Power-On Preset. Output = midscale if PRE = GND; output = zero scale if PRE = VDD. Do not let the PRE pin float.
No pull-up resistor is needed.
.
8
VDD
Positive Power Supply, 2.7 V to 5.5 V.
Rev. 0 | Page 6 of 20
AD5228
TYPICAL PERFORMANCE CHARACTERISTICS
0.10
0.10
0.08
0.06
0.04
0.02
0
T
= 25°C
–40°C
+25°C
+85°C
A
0.08
0.06
+105°C
5.5V
V
= 5.5V
DD
0.04
2.7V
0.02
0
–0.02
–0.04
–0.06
–0.08
–0.10
–0.02
–0.04
–0.06
–0.08
–0.10
0
0
0
4
8
12
16
20
24
28
32
32
32
0
4
8
12
16
20
24
28
32
32
32
CODE (Decimal)
CODE (Decimal)
Figure 7. R-INL vs. Code vs. Supply Voltages
Figure 10. R-DNL vs. Code vs. Temperature, VDD = 5 V
0.10
0.08
0.06
0.04
0.02
0
0.10
0.08
0.06
0.04
0.02
0
–40°C
+25°C
+85°C
+105°C
T
= 25°C
A
V
= 5.5V
2.7V
DD
5.5V
–0.02
–0.04
–0.06
–0.08
–0.10
–0.02
–0.04
–0.06
–0.08
–0.10
4
8
12
16
20
24
28
0
4
8
12
16
20
24
28
CODE (Decimal)
CODE (Decimal)
Figure 8. R-INL vs. Code vs. Temperature, VDD = 5 V
Figure 11. INL vs. Code vs. Supply Voltages
0.10
0.08
0.06
0.04
0.02
0
0.10
0.08
0.06
0.04
0.02
0
–40°C
+25°C
+85°C
+105°C
T
= 25°C
A
V
= 5.5V
DD
5.5V
2.7V
–0.02
–0.04
–0.06
–0.08
–0.10
–0.02
–0.04
–0.06
–0.08
–0.10
4
8
12
16
20
24
28
0
4
8
12
16
20
24
28
CODE (Decimal)
CODE (Decimal)
Figure 9. R-DNL vs. Code vs. Supply Voltages
Figure 12. INL vs. Code, VDD = 5 V
Rev. 0 | Page 7 of 20
AD5228
0.10
0.08
0.06
0.04
0.02
0
0.50
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0
T
= 25°C
A
V
V
= 2.7V
= 5.5V
DD
5.5V
DD
–0.02
–0.04
–0.06
–0.08
2.7V
–0.10
0
4
8
12
16
20
24
28
32
–40
–20
0
20
40
60
80
100
CODE (Decimal)
TEMPERATURE (°C)
Figure 13. DNL vs. Code vs. Supply Voltages
Figure 16. Zero-Scale Error vs. Temperature
0.10
0.08
0.06
0.04
0.02
0
1
–40°C
+25°C
+85°C
+105°C
V
I
= 5.5V
DD_ACT
DD
= 50µA TYP
V
= 5.5V
DD
–0.02
–0.04
–0.06
–0.08
–0.10
0.1
–40
0
4
8
12
16
20
24
28
32
–20
0
20
40
60
80
100
CODE (Decimal)
TEMPERATURE (°C)
Figure 14. DNL vs. Code, VDD = 5 V
Figure 17. Supply Current vs. Temperature
–0.50
–0.55
–0.60
–0.65
–0.70
–0.75
–0.80
–0.85
–0.90
120
100
80
60
40
20
0
V
= 5.5V
DD
R
= 100kΩ
AB
V
V
= 5.5V
= 2.7V
DD
R
R
= 50kΩ
AB
AB
DD
= 10kΩ
–40
–20
0
20
40
60
80
100
–40
–20
0
20
40
60
80
100
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 15. Full-Scale Error vs. Temperature
Figure 18. Nominal Resistance vs. Temperature
Rev. 0 | Page 8 of 20
AD5228
REF LEVEL /DIV
0dB 6.0dB
MARKER 469 390.941Hz
MAG (A/R) –8.966dB
120
100
80
60
40
20
0
6
0
T
= 25°C
V
= 2.7V
A
DD
V
= 5.5V
DD
= 50mV rms
V
A
16 STEPS
8 STEPS
–6
–12
–18
–24
–30
–36
–42
–48
–54
4 STEPS
2 STEPS
1 STEP
V
= 5.5V
DD
–40
–20
0
20
40
60
80
100
TEMPERATURE (°C)
1k
START 1 000.000Hz
10k
100k
1M
STOP 1 000 000.000Hz
Figure 19. Wiper Resistance vs. Temperature
Figure 22. Gain vs. Frequency vs. Code, RAB = 10 kΩ
REF LEVEL /DIV
0dB 6.0dB
MARKER 97 525.233Hz
MAG (A/R) –9.089dB
150
120
90
10kΩ
6
0
50kΩ
T
= 25°C
A
100kΩ
= 5.5V
A = OPEN
V
= 5.5V
DD
= 50mV rms
V
V
DD
A
16 STEPS
8 STEPS
–6
–12
–18
–24
–30
–36
–42
–48
–54
4 STEPS
2 STEPS
1 STEP
60
30
0
–30
0
4
8
12
16
20
24
28
32
CODE (Decimal)
1k
START 1 000.000Hz
10k
100k
1M
STOP 1 000 000.000Hz
Figure 20. Rheostat Mode Tempco ∆RWB/∆T vs. Code
Figure 23. Gain vs. Frequency vs. Code, RAB = 50 kΩ
REF LEVEL /DIV
0dB 6.0dB
MARKER 51 404.427Hz
MAG (A/R) –9.123dB
20
15
6
0
10kΩ
T
= 25°C
A
50kΩ
V
= 5.5V
DD
= 50mV rms
100kΩ
= V = 5.5V
V
A
V
V
16 STEPS
8 STEPS
DD
A
–6
= 0V
10
B
–12
–18
–24
–30
–36
–42
–48
–54
5
4 STEPS
2 STEPS
1 STEP
0
–5
–10
–15
–20
0
4
8
12
16
20
24
28
32
1k
START 1 000.000Hz
10k
100k
1M
STOP 1 000 000.000Hz
CODE (Decimal)
Figure 21. Potentiometer Mode Tempco ∆VWB/∆T vs. Code
Figure 24. Gain vs. Frequency vs. Code, RAB = 100 kΩ
Rev. 0 | Page 9 of 20
AD5228
0
STEP = MIDSCALE, V = V , V = 0V
DD
A
B
PU
1
–20
V
= 5V DC ±10% p-p AC
DD
V
W
V
= 3V DC ±10% p-p AC
DD
–40
V
V
V
= 5V
= 5V
= 0V
DD
A
B
2
–60
100
CH1 5.00V CH2 200mV
M2.00ms
A CH1
2.80V
1k
10k
100k
1M
T
800.000ms
FREQUENCY (Hz)
Figure 28. Autoscan Increment
Figure 25. PSRR
1.2
1.0
0.8
0.6
0.4
0.2
0
∆: 8.32ms ∆: 4.00mV
V
T
= OPEN
= 25°C
A
A
@: 8.24ms @: 378mV
PU
1
R
= 10kΩ
AB
R
= 50kΩ
V
AB
W
V
V
V
= 5V
= 5V
= 0V
DD
A
B
R
= 100k
Ω
AB
2
0
4
8
12
16
20
24
28
32
CH1 5.00V CH2 100mV
M2.00ms
A CH1
3.00V
CODE (Decimal)
T
3.92000ms
Figure 29. Maximum IWB vs. Code
Figure 26. Basic Increment
PU
1
V
W
V
V
V
= 5V
= 5V
= 0V
DD
A
B
2
CH1 5.00V CH2 100mV
M2.00ms
A CH1
2.60V
T
59.8000ms
Figure 27. Repetitive Increment
Rev. 0 | Page 10 of 20
AD5228
THEORY OF OPERATION
The AD5228 is a 32-position manual up/down digitally con-
trolled potentiometer with selectable power-on preset. The
AD5228 presets to midscale when the PRE pin is tied to ground
and to zero-scale when PRE is tied to VDD. Floating the PRE pin
is not allowed. The step-up and step-down operations require
the activation of the
(push-up) and
(push-down) pins.
PU
PD
These pins have 100 kΩ internal pull-up resistors that the
PU
activate at logic low. The common practice is to apply
and
PD
1
external pushbuttons (tactile switches) as shown in Figure 30.
D
AD5228
UP/DOWN
CONTROL
LOGIC
E
C
O
D
E
V
DD
CH1 1.00V
M100µs
A CH1
2.38V
T 20.20%
A
R1 R2
Figure 32. Close-Up of Initial Bounces
W
B
DISCRETE
STEP/AUTO
SCAN DETECT
PUSH-UP
BUTTON
PU
PD
ADAPTIVE
DEBOUNCER
ZERO- OR MID-
SCALE PRESET
PUSH-DOWN
BUTTON
PRE
GND
Figure 30. Typical Pushbutton Interface
Because of the bounce mechanism commonly found in the
switches during contact closures, a single pushbutton press
usually generates numerous bounces during contact closure.
Note that the term pushbutton refers specifically to a
1
pushbutton tactile switch or a similar switch that has 10 ms or
less bounce time during contact closure. Figure 31 shows the
characteristics of one such switch, the KRS-3550 tactile switch.
Figure 32 and Figure 33 show close ups of the initial bounces
and end bounces, respectively.
CH1 1.00V
M10.0µs
T 20.20%
A CH1
2.38V
Figure 33. Close-Up of Final Bounces
The following paragraphs describes the
operation. Similar characteristics apply to the
operation.
incrementing
PD
PU
decrementing
The AD5228 features an adaptive debouncer that monitors the
duration of the logic-low level of signal between bounces. If
PU
logic-low level signal duration is shorter than 7 ms, the
the
PU
debouncer ignores it as an invalid incrementing command.
Whenever the logic-low level of signal lasts longer than
PU
11 ms, the debouncer assumes that the last bounce is met and
therefore increments RWB by one step.
1
Repeatedly pressing the
button for fast adjustment without
PU
missing steps is allowed, provided that each press is not shorter
than tPU, which is 12 ms (see Figure 2). As a point of reference,
an advanced video game player can press a pushbutton switch
in 40 ms.
CH1 1.00V
M40.0ms
T 20.40%
A CH1
2.38V
Figure 31. Typical Tactile Switch Characteristics
Rev. 0 | Page 11 of 20
AD5228
If the
button is held for longer than 1 second, continuously
The end-to-end resistance, RAB, has 32 contact points accessed
by the wiper terminal, plus the B terminal contact if RWB is used.
PU
holding it activates autoscan mode such that the AD5228
increments by four RWB steps per second (see Figure 3).
Pushing the
pin discretely increments RWB by one step. The
PU
total resistance becomes RS + RW as shown in Figure 34. The
change of RWB can be determined by the number of discrete
executions provided that its maximum setting is not reached
Whenever the maximum RWB (= RAB) is reached, RWB stops
PU
incrementing regardless of the state of the
pin. Any continu-
PU
ous holding of the
current.
pin to logic-low simply elevates the supply
PU
during operation. ∆RWB can, therefore, be approximated as
RAB
⎛
⎞
⎟
∆RWB = + PU
+ RW
+ RW
(1)
(2)
⎜
When both
until it stops at zero scale.
and
buttons are pressed, RWB decrements
PD
PU
32
⎝
⎠
RAB
⎛
⎞
All the preceding descriptions apply to
operation. Due to
PD
∆RWB = − PD
⎜
⎟
⎠
32
⎝
the tolerance of the internal RC oscillator, all the timing
information given previously is based on the typical values,
which can vary 30%.
where:
is the number of push-up executions.
is the number of push-down executions.
AB is the end-to-end resistance.
W is the wiper resistance contributed by the on-resistance of
PU
PD
R
R
The AD5228 debouncer is carefully designed to handle common
pushbutton tactile switches. Other switches that have excessive
bounces and duration are not suitable to use in conjunction
with the AD5228.
the internal switch.
A
Similar to the mechanical potentiometer, the resistance of the
RDAC between the Wiper W and Terminal A also produces a
complementary resistance, RWA. When these terminals are used,
the B terminal can be opened or shorted to W. RWA can also be
approximated if its maximum and minimum settings are not
reached.
R
S
D0
D1
D2
D3
D4
R
R
S
S
W
B
RAB
⎛
⎜
⎞
⎟
∆RWA = −
32 − PU
)
+ RW
+ RW
3)
R
RDAC
W
32
UP/DOWN
CTRL AND
DECODE
⎝
⎠
RAB
⎛
⎜
⎞
⎟
∆RWA = +
32 − PD
)
(4)
R
S
32
⎝
⎠
R
=
R
/32
S
AB
Note that Equations 1 to 4 do not apply when
execution.
and
= 0
PD
PU
Figure 34. AD5228 Equivalent RDAC Circuit
PROGRAMMING THE DIGITAL POTENTIOMETERS
Rheostat Operation
Because in the lowest end of the resistor string, a finite wiper
resistance is present, care should be taken to limit the current
flow between W and B in this state to a maximum pulse current
of no more than 20 mA. Otherwise, degradation or possible
destruction of the internal switches can occur.
If only the W-to-B or W-to-A terminals are used as variable
resistors, the unused terminal can be opened or shorted with W.
Such operation is called rheostat mode and is shown in Figure 35.
A
A
A
The typical distribution of the resistance tolerance from device
to device is process lot dependent, and 20% tolerance is possible.
W
W
W
B
B
B
Figure 35. Rheostat Mode Configuration
Rev. 0 | Page 12 of 20
AD5228
Potentiometer Mode Operation
CONTROLLING INPUTS
If all three terminals are used, the operation is called potenti-
ometer mode. The most common configuration is the voltage
divider operation as shown in Figure 36.
All
and
inputs are protected with a Zener ESD structure
PD
PU
as shown in Figure 37.
V
DD
V
I
A
100kΩ
PU
V
DECODE
AND
DEBOUNCE
CKT
C
W
B
Figure 36. Potentiometer Mode Configuration
PU
Figure 37. Equivalent ESD Protection in and
PD
Pins
The change of VWB is known provided that the AD5228
maximum or minimum scale has not been reached during
operation. If the effect of wiper resistance is ignored, the
transfer functions can be simplified as
and
pins are usually connected to pushbutton tactile
PD
PU
switches for manual operation, but the AD5228 can also be
controlled digitally. It is recommended to add external
MOSFETs or transistors that simplify the logic controls.
PU
∆VWB = +
∆VWB = +
VA
VA
(5)
(6)
32
D
AD5228
UP/DOWN
CONTROL
LOGIC
E
V
DD
C
O
D
E
PD
A
32
R1 R2
W
B
DISCRETE
STEP/AUTO
SCAN DETECT
Unlike in rheostat mode operation where the absolute tolerance
is high, potentiometer mode operation yields an almost ratio-
metric function of
/32 or
/32 with a relatively small error
PU
PD
PU
PD
ADAPTIVE
DEBOUNCER
ZERO- OR MID-
SCALE PRESET
contributed by the RW term. The tolerance effect is, therefore,
almost canceled. Although the thin film step resistor RS and
CMOS switch resistance, RW, have very different temperature
coefficients, the ratiometric adjustment also reduces the overall
temperature coefficient effect to 5 ppm/°C except at low value
codes where RW dominates.
N1
UP
2N7002
N2
DOWN
2N7002
PRE
GND
Figure 38. Digital Control with External MOSFETs
TERMINAL VOLTAGE OPERATION RANGE
Potentiometer mode operations include an op amp input and
feedback resistors network and other voltage scaling applications.
The A, W, and B terminals can be input or output terminals and
The AD5228 is designed with internal ESD diodes for
protection. These diodes also set the voltage boundary of the
terminal operating voltages. Positive signals present on
Terminal A, B, or W that exceed VDD are clamped by the
forward-biased diode. There is no polarity constraint between
VA, VW, and VB, but they cannot be higher than VDD or lower
than GND.
have no polarity constraint provided that |VAB|, |VWA|, and |VWB
|
do not exceed VDD-to-GND.
V
DD
A
W
B
GND
Figure 39. Maximum Terminal Voltages Set by VDD and GND
Rev. 0 | Page 13 of 20
AD5228
POWER-UP AND POWER-DOWN SEQUENCES
LAYOUT AND POWER SUPPLY BIASING
Because of the ESD protection diodes that limit the voltage
compliance at Terminals A, B, and W (Figure 39), it is important
to power on VDD before applying any voltage to Terminals A, B,
and W. Otherwise, the diodes are forward-biased such that VDD
is powered on unintentionally and can affect other parts of the
circuit. Similarly, VDD should be powered down last. The ideal
power-on sequence is in the following order: GND, VDD, and
VA/B/W. The order of powering VA, VB, and VW is not important
It is always a good practice to use compact, minimum lead
length layout design. The leads to the input should be as direct
as possible with a minimum conductor length. Ground paths
should have low resistance and low inductance. It is also good
practice to bypass the power supplies with quality capacitors.
Low ESR (equivalent series resistance) 1 µF to 10 µF tantalum
or electrolytic capacitors should be applied at the supplies to
minimize any transient disturbance and to filter low frequency
ripple. Figure 39 illustrates the basic supply bypassing configu-
ration for the AD5228.
as long as they are powered on after VDD. The states of the
PU
and
pins can be logic high or floating, but they should not
PD
be logic low during power-on.
AD5228
V
V
DD
DD
+
C2
10µF
C1
0.1µF
GND
Figure 40. Power Supply Bypassing
Rev. 0 | Page 14 of 20
AD5228
APPLICATIONS
MANUAL ADJUSTABLE LED DRIVER
ADJUSTABLE HIGH POWER LED DRIVER
The AD5228 can be used in many electronics-level adjustments
such as LED drivers for LCD panel backlight controls. Figure 41
shows a manually adjustable LED driver. The AD5228 sets the
voltage across the white LED D1 for the brightness control.
Since U2 handles up to 250 mA, a typical white LED with VF of
3.5 V requires a resistor, R1, to limit U2 current. This circuit is
simple but not power efficient. The U2 shutdown pin can be
toggled with a PWM signal to conserve power.
The previous circuit works well for a single LED. Figure 43
shows a circuit that can drive three to four high power LEDs.
The ADP1610 is an adjustable boost regulator that provides the
voltage headroom and current for the LEDs. The AD5228 and
the op amp form an average gain of 12 feedback network that
servos the RSET voltage and the ADP1610 FB pin 1.2 V band gap
reference voltage. As the loop is set, the voltage across RSET is
regulated around 0.1 V and adjusted by the digital
potentiometer.
5V
C3
5V
0.1µF
V
V+
RSET
C1
C2
(8)
U1
ILED
=
1µF
0.1µF
–
AD5228
RSET
U2
AD8591
V
DD
PUSH-UP
BUTTON
A
R1
W
R
SET should be small enough to conserve power but large enough
SD 6Ω
+
PU
PD
10kΩ
B
WHITE
LED
D1
V–
to limit maximum LED current. R3 should also be used in par-
allel with AD5228 to limit the LED current within an achievable
range. A wider current adjustment range is possible by lowering
the R2 to R1 ratio as well as changing R3 accordingly.
PWM
PRE
GND
PUSH-DOWN
BUTTON
Figure 41. Low Cost Adjustable LED Driver
5V
C2
10µF
ADJUSTABLE CURRENT SOURCE FOR LED DRIVER
Because LED brightness is a function of current rather than of
forward voltage, an adjustable current source is preferred as
shown in Figure 42. The load current can be found as the VWB of
IN
R4
13.5kΩ
L1
10µF
U2
ADP1610
SD
PWM
1.2V
SW
V
OUT
C3
10µF
FB
D1
COMP
the AD5228 divided by RSET
.
R
C
SS
RT GND
100kΩ
VWB
(7)
ID1
=
C
C
D2
RSET
390pF
C
SS
10nF
D3
D4
The U1 ADP3333ARM-1.5 is a 1.5 V LDO that is lifted above or
lowered below 0 V. When VWB of the AD5228 is at its minimum,
there is no current through D1, so the GND pin of U1 is at –1.5 V
if U3 is biased with the dual supplies. As a result, some of the U2
low resistance steps have no effect on the output until the U1
GND pin is lifted above 0 V. When VWB of the AD5228 is at its
maximum, VOUT becomes VL + VAB, so the U1 supply voltage
must be biased with adequate headroom. Similarly, PWM signal
can be applied at the U1 shutdown pin for power efficiency.
C8
5V
0.1µF
U3
V+
+
AD8541
V–
R
0.25Ω
SET
–
U1
R2
U1
AD5228
L1–SLF6025-100M1R0
D1–MBR0520LT1
W
R1
100Ω
1.1kΩ
B
A
10kΩ
V
V
OUT
5V
IN
R3
200Ω
U1
ADP3333
ARM-1.5
U2
AD5228
Figure 43. Adjustable Current Source for LEDs in Series
SD
5V
V
DD
GND
PRE
PUSH-UP
BUTTON
B
PWM
W
PU
PD
10kΩ
A
GND
PUSH-DOWN
BUTTON
R
SET
0.1Ω
R1
418kΩ
5V
V+
–
U3
AD8591
+
VL
V–
D1
ID
Figure 42. Adjustable Current Source for LED Driver
Rev. 0 | Page 15 of 20
AD5228
AUTOMATIC LCD PANEL BACKLIGHT CONTROL
AUDIO AMPLIFIER WITH VOLUME CONTROL
With the addition of a photocell sensor, an automatic brightness
control can be achieved. As shown in Figure 44, the resistance of
the photocell changes linearly but inversely with the light
output. The brighter the light output, the lower the photocell
resistance and vice versa. The AD5228 sets the voltage level that
is gained up by U2 to drive N1 to a desirable brightness. With
the photocell acting as the variable feedback resistor, the change
in the light output changes the R2 resistance, therefore causing
U2 to drive N1 accordingly to regulate the output. This simple
low cost implementation of an LED controller can compensate
for the temperature and aging effects typically found in high
power LEDs. Similarly, for power efficiency, a PWM signal can
be applied at the gate of N2 to switch the LED on and off
without noticeable effect.
The AD5228 and SSM2211 can form a 1.5 W audio amplifier
with volume control that has adequate power and quality for
portable devices such as PDAs and cell phones. The SSM2211
can drive a single speaker differentially between Pins 5 and 8
without any output capacitor. The high-pass cutoff frequency is
fH1 = 1/(2 × π × R1 × C1). The SSM2211 can also drive two
speakers as shown in Figure 45. However, the speakers must be
configured in single-ended mode, and output coupling capacitors
are needed to block the dc current. The output capacitor and
the speaker load form an additional high-pass cutoff frequency
as fH2 = 1/(2 × π × R5 × C3). As a result, C3 and C4 must be
large to make the frequency as low as fH1.
±2.5V p-p
R2
10kΩ
AUDIO_INPUT
U1
5V
V
DD
C5
0.1µF
5V
5V
5V
C6
C7
0.1µF
PRE
10µF
C3
R2
PHOTOCELL
470µF
C1
1µF
R1
D1
PUSH-UP
BUTTON
R1
1kΩ
A
W
10kΩ
6
V+
U2
4
–
R5
8Ω
WHITE
LED
5
8
PU
PD
10kΩ
5V
C3
5V
0.1µF
B
SSM2211
3
GND
V–
C44
470µF
PUSH-DOWN
BUTTON
+
1
V+
C1
C2
U1
N1
1µF
0.1µF
–
7
R3
AD5228
2
4.75kΩ
U2
AD8531
R6
8Ω
V
DD
PUSH-UP
BUTTON
C2
0.1µF
A
2N7002
W
5V
–
+
PU
PD
10kΩ
B
V–
U3
AD8591
R3
10kΩ
N2
PRE
GND
+
PUSH-DOWN
BUTTON
R4
10kΩ
PWM
2N7002
Figure 45. Audio Amplifier with Volume Control
Figure 44. Automatic LCD Panel Backlight Control
Rev. 0 | Page 16 of 20
AD5228
3.50
3.49
3.48
3.47
3.46
3.45
3.44
3.43
3.42
3.41
3.40
T
= 25°C
CONSTANT BIAS WITH SUPPLY TO
RETAIN RESISTANCE SETTING
A
Users who consider EEMEM potentiometers but cannot justify
the additional cost and programming for their designs can
consider constantly biasing the AD5228 with the supply to
retain the resistance setting as shown in Figure 46. The AD5228
is designed specifically with low power to allow power conser-
vation even in battery-operated systems. As shown in Figure 47,
a similar low power digital potentiometer is biased with a 3.4 V
450 mA/hour Li-Ion cell phone battery. The measurement shows
that the device drains negligible power. Constantly biasing the
potentiometer is a practical approach because most of the
portable devices do not require detachable batteries for charging.
Although the resistance setting of the AD5228 is lost when the
battery needs to be replaced, this event occurs so infrequently
that the inconvenience is minimal for most applications.
0
2
4
6
8
10
12
DAYS
Figure 47. Battery Consumption Measurement
V
DD
U1
U2
U3
SW1
+
AD5228
V
V
DD
DD
V
DD
COMPONENT X
GND
COMPONENT Y
GND
GND
–
GND
Figure 46. Constant Bias AD5228 for Resistance Retention
Rev. 0 | Page 17 of 20
AD5228
OUTLINE DIMENSIONS
2.90 BSC
8
1
7
2
6
3
5
4
1.60 BSC
PIN 1
2.80 BSC
0.65 BSC
1.95
BSC
0.90
0.87
0.84
1.00 MAX
0.20
0.08
0.60
0.45
0.30
8°
4°
0°
0.38
0.22
0.10 MAX
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-193BA
Figure 48. 8-Lead Small Outline Transistor Package TSOT-8 [Thin SOT-23-8]
(UJ-8)
Dimensions shown in millimeters
ORDERING GUIDE
Full Container
Quantity
Model1
RAB (kΩ)
10
10
50
50
Temperature Range
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
Package Code
Package Description
TSOT-8
TSOT-8
TSOT-8
TSOT-8
TSOT-8
TSOT-8
Evaluation Board
Branding
D3K
D3K
D3L
D3L
AD5228BUJZ102-RL7
AD5228BUJZ102-R2
AD5228BUJZ502-RL7
AD5228BUJZ502-R2
UJ
UJ
UJ
UJ
UJ
UJ
3000
250
3000
250
3000
250
1
AD5228BUJZ1002-RL7 100
AD5228BUJZ1002-R2
AD5228EVAL
D3M
D3M
100
10
1
The end-to-end resistance RAB is available in 10 kΩ, 50 kΩ, and 100 kΩ. The final three characters of the part number determine the nominal resistance value, for
example,10 kΩ = 10.
2 Z = Pb-free part.
Rev. 0 | Page 18 of 20
AD5228
NOTES
Rev. 0 | Page 19 of 20
AD5228
NOTES
©
2004 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D04422–0–4/04(0)
Rev. 0 | Page 20 of 20
相关型号:
©2020 ICPDF网 联系我们和版权申明