AD590MH/883B [ADI]
2-Terminal IC Temperature Transducer;
| 型号： | AD590MH/883B |
| 厂家： | 
ADI |
| 描述： | 2-Terminal IC Temperature Transducer 传感器 换能器 |
| 文件： | 总16页 (文件大小：452K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
2-Terminal IC
Temperature Transducer
Data Sheet
AD590
FEATURES
PIN CONFIGURATIONS
Linear current output: 1 μA/K
Wide temperature range: −55°C to +150°C
Probe-compatible ceramic sensor package
2-terminal device: voltage in/current out
Laser trimmed to 0.5°C calibration accuracy (AD590M)
Excellent linearity: 0.3°C over full range (AD590M)
Wide power supply range: 4 V to 30 V
Sensor isolation from case
V+
V–
1
2
4
3
NC
NC
AD590
TOP VIEW
(Not to Scale)
PIN 5 (EXPOSED PAD)
NOTES
1. NC = NO CONNECT. THE NC PIN IS NOT
BONDED TO THE DIE INTERNALLY.
Available in 2-lead FLATPACK, 4-lead LFCSP, 3-pin TO-52,
8-lead SOIC, and die form
2. TO ENSURE CORRECT OPERATION, THE
EXPOSED PAD (EP) SHOULD BE LEFT FLOATING.
+
–
Figure 1. 2-Lead
FLATPACK
Figure 2. 4-Lead LFCSP
GENERAL DESCRIPTION
The AD590 is a 2-terminal integrated circuit temperature trans-
ducer that produces an output current proportional to absolute
temperature. For supply voltages between 4 V and 30 V, the device
acts as a high impedance, constant current regulator passing
1 μA/K. Laser trimming of the chip’s thin-film resistors is used
to calibrate the device to 298.2 μA output at 298.2 K (25°C).
–
NC
V+
V–
NC
1
2
3
4
8
7
6
5
NC
NC
NC
NC
TOP VIEW
(Not to Scale)
+
NC = NO CONNECT
The AD590 should be used in any temperature-sensing
application below 150°C in which conventional electrical
temperature sensors are currently employed. The inherent
low cost of a monolithic integrated circuit combined with the
elimination of support circuitry makes the AD590 an attractive
alternative for many temperature measurement situations.
Linearization circuitry, precision voltage amplifiers, resistance
measuring circuitry, and cold junction compensation are not
needed in applying the AD590.
Figure 3. 3-Pin TO-52
Figure 4. 8-Lead SOIC
PRODUCT HIGHLIGHTS
1. The AD590 is a calibrated, 2-terminal temperature sensor
requiring only a dc voltage supply (4 V to 30 V). Costly
transmitters, filters, lead wire compensation, and lineari-
zation circuits are all unnecessary in applying the device.
2. State-of-the-art laser trimming at the wafer level in
conjunction with extensive final testing ensures that
AD590 units are easily interchangeable.
In addition to temperature measurement, applications include
temperature compensation or correction of discrete components,
biasing proportional to absolute temperature, flow rate measure-
ment, level detection of fluids and anemometry. The AD590 is
available in die form, making it suitable for hybrid circuits and
fast temperature measurements in protected environments.
3. Superior interface rejection occurs because the output is a
current rather than a voltage. In addition, power
requirements are low (1.5 mW @ 5 V @ 25°C). These
features make the AD590 easy to apply as a remote sensor.
The AD590 is particularly useful in remote sensing applications.
The device is insensitive to voltage drops over long lines due to
its high impedance current output. Any well-insulated twisted
pair is sufficient for operation at hundreds of feet from the
receiving circuitry. The output characteristics also make the
AD590 easy to multiplex: the current can be switched by a
CMOS multiplexer, or the supply voltage can be switched by a
logic gate output.
4. The high output impedance (>10 MΩ) provides excellent
rejection of supply voltage drift. For instance, changing the
power supply from 5 V to 10 V results in only a 1 μA
maximum current change, or 1°C equivalent error.
5. The AD590 is electrically durable: it withstands a forward
voltage of up to 44 V and a reverse voltage of 20 V.
Therefore, supply irregularities or pin reversal does not
damage the device.
Rev. G
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Technical Support
©2013 Analog Devices, Inc. All rights reserved.
www.analog.com
AD590
Data Sheet
TABLE OF CONTENTS
Features.....................................................................................1
Explanation of Temperature Sensor Specifications................7
Calibration Error...................................................................7
Error vs. Temperature: Calibration Error Trimmed Out........7
Error vs. Temperature: No User Trims...................................7
Nonlinearity ..........................................................................8
Voltage and Thermal Environment Effects............................8
General Applications...............................................................10
Outline Dimensions ................................................................13
Ordering Guide ...................................................................15
General Description ..................................................................1
Pin Configurations ....................................................................1
Product Highlights ....................................................................1
Revision History........................................................................2
Specifications.............................................................................3
AD590J and AD590K Specifications......................................3
AD590L and AD590M Specifications....................................4
Absolute Maximum Ratings ......................................................5
ESD Caution..........................................................................5
Product Description ..................................................................6
REVISION HISTORY
Deleted Figure 22; Renumbered Sequentially..........................11
Changes to Figure 21 and Figure 22 ........................................11
Deleted Figure 24 ....................................................................12
Changes to Figure 24...............................................................12
Updated Outline Dimensions Section.....................................14
Changes to Ordering Guide.....................................................14
1/13—Rev. F to Rev. G
Changes to Endnote 2, Table 1...................................................3
Changes to Ordering Guide.....................................................15
11/12—Rev. E to Rev. F
Added 4-Lead LFCSP_WD ......................................... Universal
Changes to Features Section, General Description Section, and
Product Highlights Section........................................................1
Added Figure 2; Renumbered Sequentially................................1
Added Note 2, Table 1; Renumbered Sequentially.....................3
Changes to (Unbolded) For 8-Lead SOIC Package, AD590J and
AD590K Parameter, Table 1.......................................................3
Changes to Note 1, Table 3.........................................................5
Changes to Product Description Section...................................6
Change to Figure 6.....................................................................6
Changes to Explanation of Temperature Sensor Specifications
Section.......................................................................................7
Moved Nonlinearity Section......................................................8
Change to Figure 13...................................................................8
Changes to General Applications Section................................10
Changes to Figure 17 and Figure 19.........................................10
9/09—Rev. D to Rev. E
Changes to Product Description Section...................................6
Updated Outline Dimensions..................................................13
Changes to Ordering Guide.....................................................14
1/06—Rev. C to Rev. D
Updated Format ...........................................................Universal
Changes to Figure 4 Equation....................................................4
9/03—Rev. B to Rev. C
Added SOIC-8 Package ................................................Universal
Change to Figure 1 ....................................................................1
Updated Outline Dimensions..................................................13
Added Ordering Guide............................................................14
Rev. G | Page 2 of 16
Data Sheet
AD590
SPECIFICATIONS
AD590J AND AD590K SPECIFICATIONS
25°C and VS = 5 V, unless otherwise noted.1
Table 1.
AD590J2
Typ
AD590K
Typ
Parameter
Min
4
Max
Min
4
Max
Unit
POWER SUPPLY
Operating Voltage Range
OUTPUT
30
30
V
Nominal Current Output @ 25°C (298.2 K)
Nominal Temperature Coefficient
CalibrationError @ 25°C
Absolute Error (Over Rated Performance Temperature Range)
Without External CalibrationAdjustment
With25°C CalibrationError Set to Zero
Nonlinearity
298.2
1
298.2
1
µA
µA/K
°C
5.0
2.5
10
3.0
5.5
2.0
°C
°C
For TO-52 and FLATPACK Packages
For 8-Lead SOIC Package
For 4-Lead LFCSP Package
Repeatability3
1.5
1.5
1.5
0.1
0.1
0.8
°C
1.0
°C
°C
0.1
0.1
°C
°C
Long-Term Drift4
Current Noise
40
40
pA/√Hz
Power Supply Rejection
4 V ≤ VS ≤ 5 V
5 V ≤ VS ≤ 15 V
0.5
0.2
0.1
1010
100
20
0.5
0.2
0.1
1010
100
20
µA/V
µV/V
µA/V
Ω
pF
µs
15 V ≤ VS ≤ 30 V
Case Isolation to Either Lead
Effective Shunt Capacitance
Electrical Turn-On Time
Reverse Bias Leakage Current (Reverse Voltage = 10 V)5
10
10
pA
1 Specifications shown in boldface are tested on all production units at final electrical test. Results fromthose tests are used to calculate outgoing quality levels. All
minimum and maximum specifications are guaranteed, although only those shown in boldfaceare tested on all production units.
2 The LFCSP package has a reduced operating temperature range of −40°Cto +125°C.
3 Maximum deviation between +25°C readings after temperature cycling between −55°Cand +150°C; guaranteed, not tested.
4 Conditions: constant 5 V, constant 125°C;guaranteed, not tested.
5 Leakage current doubles every 10°C.
Rev. G | Page 3 of 16
AD590
Data Sheet
AD590L AND AD590M SPECIFICATIONS
25°C and VS = 5 V, unless otherwise noted.1
Table 2.
AD590L
Typ
AD590M
Typ
Parameter
Min
4
Max
Min
4
Max
Unit
POWER SUPPLY
Operating Voltage Range
OUTPUT
30
30
V
Nominal Current Output @ 25°C (298.2 K)
Nominal Temperature Coefficient
Calibration Error @ 25°C
Absolute Error (Over Rated Performance Temperature Range)
Without External Calibration Adjustment
With 25°C Calibration Error Set to Zero
Nonlinearity
298.2
1
298.2
1
μA
μA/K
°C
°C
°C
°C
°C
°C
°C
±±10
±015
±ꢀ10
±±1ꢁ
±014
0.1
±±1.
±±10
±01ꢀ
0.1
Repeatability2
Long-Term Drift3
0.1
0.1
Current Noise
40
40
pA/√Hz
Power Supply Rejection
4 V ≤ VS ≤ 5 V
5 V ≤ VS ≤ 15 V
0.5
0.2
0.1
1010
100
20
0.5
0.2
0.1
1010
100
20
μA/V
μA/V
μA/V
Ω
pF
μs
15 V ≤ VS ≤ 30 V
Case Isolation to Either Lead
Effective Shunt Capacitance
Electrical Turn-On Time
Reverse Bias Leakage Current (Reverse Voltage = 10 V)4
10
10
pA
1 Specifications shown in boldface are tested on all production units at final electrical test. Results from those tests are used to calculate outgoing quality levels. All
minimum and maximum specifications are guaranteed, although only those shown in boldface are tested on all production units.
2 Maximum deviation between +25°C readings after temperature cycling between −55°C and +150°C; guaranteed, not tested.
3 Conditions: constant 5 V, constant 125°C; guaranteed, not tested.
4 Leakage current doubles every 10°C.
°K
°C
+223°
–50°
+273° +298° +323°
0° +25° +50°
+373°
+100°
+423°
+150°
°F –100°
0°
+100°
+32° +70°
+200°
+212°
+300°
5
9
C
F 32
K C 273.15
9
5
F
C 32 R F 459.7
Figure 5. Temperature Scale Conversion Equations
Rev. G | Page 4 of 16
Data Sheet
AD590
ABSOLUTE MAXIMUM RATINGS
Table 3.
Parameter
Stresses above those listed under Absolute Maximum Ratings
Rating
may cause permanent damage to the device. This is a stress
rating only and functional operation of the device at these or
any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Forward Voltage ( E+ or E−)
Reverse Voltage (E+ to E−)
Breakdown Voltage (Case E+ or E−)
Rated Performance Temperature Range1
Storage Temperature Range1
Lead Temperature (Soldering, 10 sec)
44 V
−20 V
200 V
−55°C to +150°C
−65°C to +155°C
300°C
1 The AD590 was used at −100°C and +200°C for short periods of
measurement with no physical damage to the device. However, the absolute
errors specified apply to only the rated performance temperature range.
Applicable to 2-lead FLATPACK and 3-pin TO-52 packages only.
ESD CAUTION
Rev. G | Page 5 of 16
AD590
Data Sheet
PRODUCT DESCRIPTION
The AD590 is a 2-terminal temperature-to-voltage transducer. It
is available in a variety of accuracy grades and packages. When
using the AD590 in die form, the chip substrate must be kept
electrically isolated (floating) for correct circuit operation.
Figure 8 shows the typical V–I characteristic of the circuit at
25°C and the temperature extremes.
+
R1
R2
260Ω
1040Ω
1725µM
Q2
Q5
Q3
Q1
Q4
C1
Q6
26pF
V–
Q12
1090µM
Q8
Q7
R4
11kΩ
V+
CHIP
SUBSTRATE
R3
5kΩ
Q9
Q10
Figure 6. Metallization Diagram
Q11
1
8
1
The AD590 uses a fundamental property of the silicon
transistors from which it is made to realize its temperature
proportional characteristic: if two identical transistors are
operated at a constant ratio of collector current densities, r,
then the difference in their base-emitter voltage is (kT/q)(In r).
Because both k (Boltzman’s constant) and q (the charge of an
electron) are constant, the resulting voltage is directly pro-
portional to absolute temperature (PTAT). (For a more detailed
description, see M.P. Timko, “A Two-Terminal IC Temperature
Transducer,” IEEE J. Solid State Circuits, Vol. SC-11, p. 784-788,
Dec. 1976. Understanding the Specifications–AD590.)
R5
146Ω
R6
820Ω
–
Figure 7. Schematic Diagram
+150°C
423
+25°C
–55°C
298
218
In the AD590, this PTAT voltage is converted to a PTAT current
by low temperature coefficient thin-film resistors. The total
current of the device is then forced to be a multiple of this
PTAT current. Figure 7 is the schematic diagram of the AD590.
In this figure, Q8 and Q11 are the transistors that produce the
PTAT voltage. R5 and R6 convert the voltage to current. Q10,
whose collector current tracks the collector currents in Q9 and
Q11, supplies all the bias and substrate leakage current for the
rest of the circuit, forcing the total current to be PTAT. R5 and
R6 are laser-trimmed on the wafer to calibrate the device at 25°C.
0
1
2
3
4
5
6
30
SUPPLY VOLTAGE (V)
Figure 8. V–I Plot
Rev. G | Page 6 of 16
Data Sheet
AD590
temperature range. In most applications, there is a current-to-
voltage conversion resistor (or, as with a current input ADC, a
reference) that can be trimmed for scale factor adjustment.
EXPLANATION OF TEMPERATURE SENSOR
SPECIFICATIONS
The way in which the AD590 is specified makes it easy to apply
it in a wide variety of applications. It is important to understand
the meaning of the various specifications and the effects of the
supply voltage and thermal environment on accuracy.
+
5V
+
AD590
–
+
R
The AD590 is a PTAT current regulator. (Note that T (°C) =
T (K) − 273.2. Zero on the Kelvin scale is absolute zero; there is
no lower temperature.) That is, the output current is equal to a
scale factor times the temperature of the sensor in degrees
Kelvin. This scale factor is trimmed to 1 μA/K at the factory, by
adjusting the indicated temperature (that is, the output current)
to agree with the actual temperature. This is done with 5 V
across the device at a temperature within a few degrees of 25°C
(298.2 K). The device is then packaged and tested for accuracy
over temperature.
100Ω
V
= 1mV/K
–
T
950Ω
–
Figure 10. One Temperature Trim
ERROR VS. TEMPERATURE: CALIBRATION ERROR
TRIMMED OUT
Each AD590 is tested for error over the temperature range with
the calibration error trimmed out. This specification could also
be called the variance from PTAT, because it is the maximum
difference between the actual current over temperature and a
PTAT multiplication of the actual current at 25°C. This error
consists of a slope error and some curvature, mostly at the
temperature extremes. Figure 11 shows a typical AD590K
temperature curve before and after calibration error trimming.
CALIBRATION ERROR
At final factory test, the difference between the indicated
temperature and the actual temperature is called the calibration
error. Since this is a scale factory error, its contribution to the
total error of the device is PTAT. For example, the effect of the
1°C specified maximum error of the AD590L varies from 0.73°C
at −55°C to 1.42°C at 150°C. Figure 9 shows how an exaggerated
calibration error would vary from the ideal over temperature.
2
BEFORE
CALIBRATION
TRIM
CALIBRATION
ERROR
ACTUAL
TRANSFER
FUNCTION
0
AFTER
CALIBRATION
TRIM
I
ACTUAL
298.2
IDEAL
TRANSFER
FUNCTION
CALIBRATION
ERROR
–2
–55
150
TEMPERATURE (°C)
Figure 11. Effect to Scale Factor Trim on Accuracy
ERROR VS. TEMPERATURE: NO USER TRIMS
298.2
TEMPERATURE (°K)
Using the AD590 by simply measuring the current, the total
error is the variance from PTAT, described above, plus the effect
of the calibration error over temperature. For example, the
AD590L maximum total error varies from 2.33°C at −55°C to
3.02°C at 150°C. For simplicity, only the large figure is shown
on the specification page.
Figure 9. Calibration Error vs. Temperature
The calibration error is a primary contributor to the maximum
total error in all AD590 grades. However, because it is a scale
factor error, it is particularly easy to trim. Figure 10 shows the
most elementary way of accomplishing this.
To trim this circuit, the temperature of the AD590 is measured
by a reference temperature sensor and R is trimmed so that VT
= 1 mV/K at that temperature. Note that when this error is
trimmed out at one temperature, its effect is zero over the entire
Rev. G | Page 7 of 16
AD590
Data Sheet
NONLINEARITY
Nonlinearity as it applies to the AD590 is the maximum
deviation of current over temperature from a best-fit straight
line. The nonlinearity of the AD590 over the −55°C to +150°C
range is superior to all conventional electrical temperature
sensors such as thermocouples, RTDs, and thermistors. Figure 12
shows the nonlinearity of the typical AD590K from Figure 11.
2
0
1.6
0.8
–2
–55
0
100
150
0.8°C MAX
TEMPERATURE (°C)
Figure 14. Typical 2-Trim Accuracy
0
0.8°C
MAX
0.8°C
MAX
VOLTAGE AND THERMAL ENVIRONMENT EFFECTS
The power supply rejection specifications show the maximum
expected change in output current vs. input voltage changes.
The insensitivity of the output to input voltage allows the use of
unregulated supplies. It also means that hundreds of ohms of
resistance (such as a CMOS multiplexer) can be tolerated in
series with the device.
–0.8
–1.6
–55
150
TEMPERATURE (°C)
Figure 12. Nonlinearity
Figure 13 shows a circuit in which the nonlinearity is the major
contributor to error over temperature. The circuit is trimmed
by adjusting R1 for a 0 V output with the AD590 at 0°C. R2 is
then adjusted for 10 V output with the sensor at 100°C. Other
pairs of temperatures can be used with this procedure as long as
they are measured accurately by a reference sensor. Note that
for 15 V output (150°C), the V+ of the op amp must be greater
than 17 V. Also, note that V− should be at least −4 V; if V− is
ground, there is no voltage applied across the device.
15V
It is important to note that using a supply voltage other than 5 V
does not change the PTAT nature of the AD590. In other words,
this change is equivalent to a calibration error and can be
removed by the scale factor trim (see Figure 11).
The AD590 specifications are guaranteed for use in a low
thermal resistance environment with 5 V across the sensor.
Large changes in the thermal resistance of the sensor’s environment
change the amount of self-heating and result in changes in the
output, which are predictable but not necessarily desirable.
The thermal environment in which the AD590 is used
determines two important characteristics: the effect of self-
heating and the response of the sensor with time. Figure 15 is a
model of the AD590 that demonstrates these characteristics.
R1
2kΩ
R2
5kΩ
35.7kΩ
97.6kΩ
AD581
30pF
T
θ
T
θ
J
JC
C
CA
27kΩ
100mV/°C
= 100mV/°C
OP177
V
+
–
T
P
T
A
AD590
C
C
C
CH
V–
Figure 15. Thermal Circuit Model
Figure 13. 2-Temperature Trim
Rev. G | Page 8 of 16
Data Sheet
AD590
As an example, for the TO-52 package, θJC is the thermal
resistance between the chip and the case, about 26°C/W. θCA is
the thermal resistance between the case and the surroundings
and is determined by the characteristics of the thermal
connection. Power source P represents the power dissipated
on the chip. The rise of the junction temperature, TJ, above the
ambient temperature, TA, is
The time response of the AD590 to a step change in
temperature is determined by the thermal resistances and the
thermal capacities of the chip, CCH, and the case, CC. CCH is
about 0.04 Ws/°C for the AD590. CC varies with the measured
medium, because it includes anything that is in direct thermal
contact with the case. The single time constant exponential
curve of Figure 16 is usually sufficient to describe the time
response, T (t). Table 4 shows the effective time constant, τ, for
several media.
TJ − TA = P(θJC + θCA)
(1)
Table 4 gives the sum of θJC and θCA for several common
thermal media for both the H and F packages. The heat sink
used was a common clip-on. Using Equation 1, the temperature
rise of an AD590 H package in a stirred bath at 25°C, when
driven with a 5 V supply, is 0.06°C. However, for the same
conditions in still air, the temperature rise is 0.72°C. For a given
supply voltage, the temperature rise varies with the current and
is PTAT. Therefore, if an application circuit is trimmed with the
sensor in the same thermal environment in which it is used, the
scale factor trim compensates for this effect over the entire
temperature range.
T
FINAL
–t/
) × (1 – e )
INITIAL
T(t) = T
INITIAL
+ (T
– T
FINAL
Table 4. Thermal Resistance
T
INITIAL
θJC + θCA
4
TIME
(°C/Watt)
τ (sec)1
F
Figure 16. Time Response Curve
Medium
H
F
H
Aluminum Block
Stirred Oil2
Moving Air3
30
42
10
60
0.6
1.4
0.1
0.6
With Heat Sink
Without Heat Sink
Still Air
45
115
–
190
5.0
13.5
–
10.0
With Heat Sink
Without Heat Sink
191
480
–
650
108
60
–
30
1 τ is dependent upon velocity of oil; average of several velocities listed above.
2 Air velocity @ 9 ft/sec.
3 The time constant is defined as the time required to reach 63.2% of an
instantaneous temperature change.
Rev. G | Page 9 of 16
AD590
Data Sheet
GENERAL APPLICATIONS
V+
Figure 17 shows a typical use of the AD590 in a remote
temperature sensing application. The AD590 is used as a
thermometer circuit that measures temperature from −55°C to
+150°C, with an output voltage of 1 mV/°K. Because the
AD590 measures absolute temperature (its nominal output is
1 mA/K), the output must be offset by 273.2 mA to read out in
degrees Celsius.
R3
10kΩ
+
–
AD590L
#2
–
+
OP177
+
–
R1
5MΩ
AD590L
#1
(T1 – T2) × (10mV/°C)
R2
50kΩ
R4
10kΩ
V–
+
I
T
AD590
7V
Figure 19. Differential Measurements
–
Figure 20 is an example of a cold junction compensation circuit
for a Type J thermocouple using the AD590 to monitor the
reference junction temperature. This circuit replaces an ice-bath
as the thermocouple reference for ambienttemperatures
between 15°C and 35°C. The circuit is calibrated by adjusting RT
for a proper meter reading with the measuring junction at a
known reference temperature and the circuit near 25°C. Using
components with the TCsas specified in Figure 20, compensation
accuracy is within 0.5°C for circuit temperatures between 15°C
and 35°C. Otherthermocouple typescan be accommodated with
different resistor values. Note thatthe TCs of the voltage
reference and the resistors are the primary contributors to error.
I
T
I
T
1k
0.1% LOW
TCR RESISTOR
1mV/k
Figure 17. Variable Scale Display
Connecting several AD590 units in series, as shown in Figure 18,
allows the minimum of all the sensed temperatures to be
indicated. In contrast, using the sensors in parallel yields the
average of the sensed temperatures.
7.5V
IRON
REFERENCE
JUNCTION
15V
+
+
CONSTANTAN
AD590
AD590
–
–
5V
+
–
+
+
–
+
–
+
AD590
–
AD580
C
AD590
–
+
–
U
+
52.3Ω
MEASURING
JUNCTION
+
V
AD590
–
OUT
–
8.66kΩ
+
+
10kΩ
(0.1%)
333.3Ω
(0.1%)
METER
V
MIN
V AVG
T
T
R
T
–
–
1kΩ
RESISTORS ARE 1%, 50ppm/°C
Figure 18. Series and Parallel Connection
Figure 20. Cold Junction Compensation Circuit for Type J Thermocouple
The circuit in Figure 19 demonstrates one method by which
differential temperature measurements can be made. R1 and R2
can be used to trim the output of the op amp to indicate a
desired temperature difference. For example, the inherent offset
between the two devices can be trimmed in. If V+ and V− are
radically different, then the difference in internal dissipation
causes a differential internal temperature rise. This effect can be
used to measure the ambient thermal resistance seen by the
sensorsin applications such asfluid-level detectors oranemometry.
Rev. G | Page 10 of 16
Data Sheet
AD590
V+
Figure 21 is an example of a current transmitter designed to be
used with 40 V, 1 kΩ systems; it uses its full current range of 4
to 20 mA for a narrow span of measured temperatures. In this
example, the 1 µA/K output of the AD590 is amplified to
1 mA/°C and offset so that 4 mA is equivalent to 17°C and
20 mA is equivalent to 33°C. RT is trimmed for proper reading
at an intermediate reference temperature. With a suitable choice
of resistors, any temperature range within the operating limits
of the AD590 can be chosen.
AD581
V+
V–
OUT
10V
HEATING
ELEMENTS
+
–
R
B
R
H
AD590
7
2
3
–
+
R
SET
AD790
4
1
R
L
C1
10kΩ
V+
GND
Figure 22. Simple Temperature Control Circuit
+
–
AD581
4mA = 17°C
12mA = 25°C
20mA = 33°C
V
The voltage compliance and the reverse blocking characteristic
of the AD590 allow it to be powered directly from 5 V CMOS
logic. This permits easy multiplexing, switching, or pulsing for
minimum internal heat dissipation. In Figure 23, any AD590
connected to a logic high passes a signal current through the
current measuring circuitry, while those connected to a logic
zero pass insignificant current. The outputs used to drive the
AD590s can be employed for other purposes, but the additional
capacitance due to the AD590 should be taken into account.
OUT
35.7kΩ
30pF
R
T
5kΩ
+
–
+
AD590
OP177
–
5kΩ
500Ω
12.7kΩ
10Ω
0.01µF
10kΩ
5V
V–
Figure 21. 4 to 20 mA Current Transmitter
Figure 22 is an example of a variable temperature control circuit
(thermostat) using the AD590. RH and RL are selected to set the
high and low limits for RSET. RSET could be a simple pot, a
calibrated multiturn pot, or a switched resistive divider. Powering
the AD590 from the 10 V reference isolatesthe AD590 from
supply variations while maintaining a reasonable voltage (~7 V)
across it. Capacitor C1 is often needed to filter extraneous noise
from remote sensors. RB is determined by the β of the power
transistor and the current requirements of the load.
+
AD590
–
CMOS
GATES
+
–
+
–
+
–
1kΩ (0.1%)
Figure 23. AD590 Driven from CMOS Logic
Rev. G | Page 11 of 16
AD590
Data Sheet
Figure 24 demonstrates a method of multiplexing the AD590 in
the 2-trim mode (see Figure 13 and Figure 14). Additional
AD590s and their associated resistors can be added to multiplex
up to eight channels of 0.5°C absolute accuracy over the
temperature range of −55°C to +125°C. The high temperature
restriction of 125°C is due to the output range of the op amps;
output to 150°C can be achieved by using a 20 V supply for the
op amp.
2kΩ
2kΩ
5kΩ
35.7kΩ
35.7kΩ
97.6kΩ
97.6kΩ
+15V
+
5kΩ
AD581
–
V
OUT
V+
S1
S2
OP177
10mV/°C
DECODER/
DRIVER
–15V
27kΩ
S8
AD7501
+15V
–15V
TTL/DTL TO CMOS
INTERFACE
+
–
+
EN
BINARY
CHANNEL
SELECT
AD590L
AD590L
–
–5V TO –15V
Figure 24. 8-Channel Multiplexer
Rev. G | Page 12 of 16
Data Sheet
AD590
OUTLINE DIMENSIONS
0.030 (0.76)
TYP
POSITIVE LEAD
INDICATOR
0.019 (0.48)
0.017 (0.43)
0.015 (0.38)
0.093 (2.36)
0.081 (2.06)
0.055 (1.40)
0.050 (1.27)
0.045 (1.14)
0.500 (12.69)
MIN
0.210 (5.34)
0.200 (5.08)
0.190 (4.83)
0.240 (6.10)
0.230 (5.84)
0.220 (5.59)
0.0065 (0.17)
0.0050 (0.13)
0.0045 (0.12)
0.050 (1.27)
0.041 (1.04)
0.015 (0.38)
TYP
Figure 25. 2-Lead Ceramic Flat Package [FLATPACK]
(F-2)
Dimensions shown in inches and (millimeters)
0.500 (12.70)
MIN
0.150 (3.81)
0.115 (2.92)
0.250 (6.35) MIN
0.050 (1.27) MAX
0.050 (1.27) T.P.
0.048 (1.22)
0.028 (0.71)
3
0.100
(2.54)
T.P.
2
0.046 (1.17)
0.036 (0.91)
1
0.050
0.019 (0.48)
0.016 (0.41)
(1.27)
T.P.
0.030 (0.76) MAX
45° T.P.
0.021 (0.53) MAX
BASE & SEATING PLANE
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 26. 3-Pin Metal Header Package [TO-52]
(H-03-1)
Dimensions shown in inches and (millimeters)
Rev. G | Page 13 of 16
AD590
Data Sheet
5.00 (0.1968)
4.80 (0.1890)
8
1
5
4
6.20 (0.2441)
5.80 (0.2284)
4.00 (0.1574)
3.80 (0.1497)
0.50 (0.0196)
0.25 (0.0099)
1.27 (0.0500)
BSC
45°
1.75 (0.0688)
1.35 (0.0532)
0.25 (0.0098)
0.10 (0.0040)
8°
0°
0.51 (0.0201)
0.31 (0.0122)
COPLANARITY
0.10
1.27 (0.0500)
0.40 (0.0157)
0.25 (0.0098)
0.17 (0.0067)
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MS-012-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 27. 8-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
(R-8)
Dimensions shown in millimeters and (inches)
1.65
1.55
1.45
2.10
2.00
1.90
0.80 REF
0.20 MIN
3
4
3.10
3.00
2.90
EXPOSED
PAD
1.80
1.70
1.60
0.50
0.40
0.30
PIN 1 INDEX
AREA
2
1
PIN 1
INDICATOR
(R 0.15)
TOP VIEW
BOTTOM VIEW
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATIONS
0.80
0.75
0.70
0.05 MAX
0.00 MIN
0.203 REF
SECTION OF THIS DATA SHEET.
0.35
0.30
0.25
SEATING
PLANE
COPLANARITY
0.08
COMPLIANT TO JEDEC STANDARDS MO-229
Figure 28. 4-Lead Lead Frame Chip Scale Package [LFCSP_WD]
2.00 mm × 3.00 mm Body, Very Very Thin, Dual Lead
(CP-4-1)
Dimensions shown in millimeters
Rev. G | Page 14 of 16
Data Sheet
AD590
ORDERING GUIDE
Model1, 2
Temperature Range
−55°C to +150°C
−55°C to +150°C
−55°C to +150°C
−55°C to +150°C
−55°C to +150°C
−55°C to +150°C
−55°C to +150°C
−55°C to +150°C
−55°C to +150°C
−55°C to +150°C
−55°C to +150°C
−55°C to +150°C
−55°C to +150°C
−55°C to +150°C
−55°C to +150°C
−40°C to +125°C
−40°C to +125°C
Package Description
2-Lead FLATPACK
3-Pin TO-52
8-Lead SOIC_N
8-Lead SOIC_N
2-Lead FLATPACK
3-Pin TO-52
Package Option
F-2
H-03-1
R-8
Branding
AD590JF
AD590JH
AD590JR
AD590JRZ
AD590KF
AD590KH
R-8
F-2
H-03-1
R-8
R-8
AD590KR
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
2-Lead FLATPACK
3-Pin TO-52
2-Lead FLATPACK
3-Pin TO-52
Bare Die
AD590KR-REEL
AD590KRZ
AD590KRZ-RL
AD590LF
AD590LH
AD590MF
R-8
R-8
F-2
H-03-1
F-2
AD590MH
AD590JCHIPS
AD590JCPZ-R5
AD590JCPZ-RL7
H-03-1
H-03-1
CP-4-1
CP-4-1
4-Lead LFCSP_WD
4-Lead LFCSP_WD
7A
7A
1 Z = RoHS Compliant Part.
2 The AD590xF models and the AD590xHmodels are available in 883B.
Rev. G | Page 15 of 16
AD590
NOTES
Data Sheet
©2013 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D00533-0-1/13(G)
Rev. G | Page 16 of 16
相关型号：
AD592AN
ANALOG TEMP SENSOR-CURRENT, 0.15Cel, RECTANGULAR, THROUGH HOLE MOUNT, TO-92, 3 PIN
ROCHESTER
AD592BN
ANALOG TEMP SENSOR-CURRENT, 0.15Cel, RECTANGULAR, THROUGH HOLE MOUNT, TO-92, 3 PIN
ROCHESTER
AD592CN
ANALOG TEMP SENSOR-CURRENT, 0.15Cel, RECTANGULAR, THROUGH HOLE MOUNT, TO-92, 3 PIN
ROCHESTER
©2020 ICPDF网 联系我们和版权申明