AD71028JST [ADI]
Dual Digital BTSC Encoder with Integrated DAC; 双数字BTSC编码器，集成了DAC
| 型号： | AD71028JST |
| 厂家： | 
ADI |
| 描述： | Dual Digital BTSC Encoder with Integrated DAC |
| 文件： | 总20页 (文件大小：435K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Dual Digital BTSC Encoder
with Integrated DAC
AD71028
PRODUCT OVERVIEW
FEATURES
2 complete independent BTSC encoders
Pilot tone generator
Includes subcarrier modulation
Typical 23 dB to 27 dB separation, 16 dB minimum
Signal bandwidth of 14 kHz
Phat-StereoTM algorithm for stereo image enhancement
Dialog enhancement function for playing wide dynamic
range video sources over built-in TV speakers
Includes L-R dual-band compressor
SPI® port for control of modes and effects
Differential output for optimum performance
DAC performance: 92 dB dynamic range, –92 dB THD+N
Output level control for setting aural carrier deviation
Flexible serial data port with right-justified, left-justified,
I2S compatible, and DSP serial port modes
48-lead LQFP plastic package
The AD71028 dual digital BTSC encoder provides two complete
digital BTSC encoder channels, including the pilot-tone
generation and subcarrier mixing functions. Two built-in high
performance DACs are provided to output the BTSC baseband
composite signal. The output of the AD71028 can be connected
with minimal external circuitry to the input of a 4.5 MHz aural
FM modulator.
In addition to the BTSC encoders, the AD71028 also includes a
stereo image enhancement function, Phat Stereo, to increase the
sense of spaciousness available from closely spaced TV
loudspeakers. A dialog enhancement algorithm is also included
to solve the problem of playing wide dynamic range sources
over limited-performance TV speakers and amplifiers. An
extensive SPI port allows click-free parameter updates.
The AD71028 also includes ADI’s patented multibit Σ-∆ DAC
architecture. This architecture provides 92 dB SNR and THD+N
of –92 dB.
APPLICATIONS
Digital set-top box BTSC encoder
FUNCTIONAL BLOCK DIAGRAM
3
SERIAL
INPUT A
SERIAL
INPUT
BTSC
ENCODER
PLL DIVIDERS
CORE A
BTSC
ENCODED
OUTPUT A
CLOCK
DOUBLER
DAC
CLOCK
SIGNAL
GROUP
ANALOG
BIAS
BIAS
CLOCK
DOUBLER
BTSC
ENCODER
CORE B
PLL DIVIDERS
SPI PORT
BTSC
ENCODED
OUTPUT B
DAC
SERIAL
INPUT
3
SERIAL
INPUT B
4
CONTROL REGISTERS
PARAMETER RAM
SPI I/O
GROUP
AD71028
Figure 1. Functional Block Diagram
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.326.8703
www.analog.com
© 2004 Analog Devices, Inc. All rights reserved.
AD71028
TABLE OF CONTENTS
Specifications..................................................................................... 3
DAC Analog Performance........................................................... 3
BTSC Encoder Performance....................................................... 3
Digital I/O ..................................................................................... 3
Power.............................................................................................. 4
Temperature Range ...................................................................... 4
Digital Timing............................................................................... 4
Absolute Maximum Ratings............................................................ 5
Pin Configuration and Functional Descriptions.......................... 6
Features .............................................................................................. 8
Pin Functions ................................................................................ 8
Signal Processing ............................................................................ 10
Background of BTSC ................................................................. 10
Performance Factors .................................................................. 10
Separation Alignment................................................................ 10
Phase Linearity of the External Analog Filter......................... 11
Input Levels................................................................................. 11
Clock Relationships.................................................................... 11
SPI Port ............................................................................................ 12
Overview ..................................................................................... 12
SPI Address Decoding ............................................................... 12
Parameter RAM.......................................................................... 13
Control Register ......................................................................... 13
Output Level Register ................................................................ 13
Stereo Enhancement Register................................................... 13
Dialog Enhancement Register .................................................. 13
SPI Read/Write Data Formats .................................................. 14
Initialization................................................................................ 14
Serial Data Input Port................................................................ 14
Analog Output Section.................................................................. 16
Outline Dimensions....................................................................... 17
Ordering Guide .......................................................................... 17
REVISION HISTORY
Revision 0: Initial Version
Rev. 0 | Page 2 of 20
AD71028
SPECIFICATIONS
TEST CONDITIONS, UNLESS OTHERWISE NOTED
Supply Voltages (AVDD, DVDD
Ambient Temperature
Input Clock
)
5.0 V
25°C
12.288 MHz
1 kHz, 0 dBFS
48 kHz
20 Hz to 14 kHz
24 Bits
Input Signal
Input Sample Rate
Measurement Bandwidth
Word Width
Load Capacitance
Input Voltage HI
50 pF
2.4 V
Input Voltage LO
0.4 V
DAC ANALOG PERFORMANCE
Table 1.
Parameter
Min
85
Typ
24
Max
Unit
Bits
dB
Resolution
Dynamic Range (20 Hz to 14 kHz, –60 dB Input) (Encoded Output, Left = Right)
Total Harmonic Distortion + Noise (Encoded Output, Left = Right, 20 Hz to 14 kHz)
VIN = 0 dB
921
–85
–921
1.7
dB
V p-p
Differential Output Range ( Full Scale, Left = Right)
1Measurement of encoded BTSC signal, not a measurement of end-to-end system.
BTSC ENCODER PERFORMANCE
Table 2.
Parameter
Min
Typ
Max
Unit
Channel Separation1
30 Hz to 500 Hz
500 Hz to 5 kHz
5 kHz to 13.5 kHz
Frequency Response1
30 Hz to 10 kHz
30 Hz to 13.5 kHz
27
23
16
dB
dB
dB
+0.5
+0.5
–1.0
–1.5
dB
dB
1These specifications are measured with a –25 dB, 1 kHz input signal.
DIGITAL I/O
Table 3.
Parameter
Min
Typ
Max
Unit
Input Voltage HI (VIH)
2.1
V
Input Voltage LO (VIL)
0.8
10
10
V
Input Leakage (IIH @ VIH = 2.4 V)
Input Leakage (IIL @ VIL = 0.8 V)
High Level Output Voltage (VOH) IOH = 2 mA
Low Level Output Voltage (VOL) IOL = 2 mA
µA
µA
V
DVDD – 0.5
0.4
V
Rev. 0 | Page 3 of 20
AD71028
POWER
Table 4.
Parameter
Min
Typ
Max
Unit
Supplies
Voltage, Analog and Digital
Analog Current
Digital Current
4.5
5
31
97
5.5
37
110
V
mA
mA
Dissipation
Operation—Both Supplies
Operation—Analog Supplies
Operation—Digital Supplies
640
155
485
mW
mW
mW
TEMPERATURE RANGE
Table 5.
Parameter
Min
Typ
25
Max
Unit
°C
°C
Specifications Guaranteed
Functionality Guaranteed
Storage
0
–55
70
+125
°C
DIGITAL TIMING
Table 6.
Parameter
Min
40
25
10
0
Typ
Max
Unit
%
tDMD
tDBL
tDBH
tDLS
tDLH
tDDS
tDDH
tCCL
tCCH
tCLS
tCLH
tCLD
tCDS
tCDH
tRLP
MCLK Recommended Duty Cycle @ 12.288 MHz (256 × fS and 512 × fS Modes)
60
BCLK Low Pulse Width
BCLK High Pulse Width
LRCLK Setup
LRCLK Hold
SDATA Setup
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
10
0
SDATA Hold
10
10
10
10
20
10
0
CCLK Low Pulse Width
CCLK High Pulse Width
CLATCH Setup
CLATCH Hold
CLATCH High Pulse Width
CDATA Setup
CDATA Hold
Reset LO Pulse Width
10
10
Rev. 0 | Page 4 of 20
AD71028
ABSOLUTE MAXIMUM RATINGS
Table 7. AD71028 Stress Ratings
Table 8. Package Characteristics (48-Lead LQFP)
Parameter
Min
Max
Unit
V
V
V
V
V
V
V
Parameter
Min
Typ
Max
Unit
°C/W
°C/W
DVDD to DGND
ODVDD to DGND
AVDD to AGND
Digital Inputs
Analog Inputs
AGND to DGND
Reference Voltage
Maximum Junction
Temperature
–0.3
–0.3
–0.3
DGND – 0.3
AGND – 0.3
–0.3
+6
+6
+6
DVDD + 0.3
AVDD + 0.3
+0.3
θJA Thermal Resistance
[Junction-to-Ambient]
θJC Thermal Resistance
[Junction-to-Case]
72
19.5
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
(AVDD + 0.3)/2
125
°C
Storage Temperature
Range
Soldering
–65
+150
300
10
°C
°C
sec
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 5 of 20
AD71028
PIN CONFIGURATION AND FUNCTIONAL DESCRIPTIONS
48 47 46 45 44 43 42 41 40 39 38 37
DIV2_PA
DIV1_PB
DIV2_PB
NC
1
2
3
4
5
6
7
8
9
36 AGND
35 OUTB–
34 OUTB+
33 AVDD
32 AGND
31 AVDD
30 OUTA+
29 OUTA–
28 AGND
27 NC
NC
AD71028
DGND
DVDD
ODVDD
NC
TOP VIEW
(Not to Scale)
NC 10
COUT 11
CDATA 12
26 NC
25 DOUBLE
13 14 15 16 17 18 19 20 21 22 23 24
NC = NO CONNECT
Figure 2. 48-Lead Low Profile Quad Flat Pack (LQFP)
Table 9. Pin Function Descriptions
Pin No.
Mnemonic
DIV2_PA
DIV1_PB
DIV2_PB
NC
Input/Output
Description
1
2
3
OUT
OUT
OUT
CLK27_PA clock (Pin 40) Divided by 1125
PLL_PB Clock (Pin 46) Divided by 512 (DOUBLE = 1) or 1024 (DOUBLE = 0)
CLK27_PB Clock (Pin 41) Divided by 1125
No Connection
4, 5, 9, 10, 26, 27, 39
6, 16, 44
DGND
Digital Ground
7, 13, 17, 45
DVDD
Digital Supply for DSP Core
8
11
12
14
15
18
19
20
21
22
23
24
25
28, 32, 36
29
30
31, 33
34
ODVDD
COUT
CDATA
CCLK
Digital Supply for Output Buffers
SPI Readback
SPI Control Data Input
SPI Serial Bit Clock
SPI Control Latch Signal
Reset Signal for Both Processors, Active Low
Data Input to Processor A
Bit Clock Signal for Serial Data Input to Processor A
Left/Right Framing Signal for Data Input to Processor A
Data Input to Processor B
Bit Clock Signal for Serial Data Input to Processor B
Left/Right Framing Signal for Data Input to Processor B
Enables Internal Clock Doubler for 12.288 MHz Input (Both Processors)
Analog Ground
Negative Analog Output, Processor A
Positive Analog Output, Processor A
Analog Supply
OUT
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
CLATCH
RESETB
SDATA_PA
BCLK_PA
LRCLK_PA
SDATA_PB
BCLK_PB
LRCLK_PB
DOUBLE
AGND
OUTA–
OUTA+
AVDD
OUTB+
OUTB–
REFCAP
FILTCAP
OUT
OUT
OUT
OUT
IN
Positive Analog Output, Processor B
Negative Analog Output, Processor B
Connection Point for 10 µF VREF Filter Capacitor
Connection for Noise Reduction Capacitor
35
37
38
IN
Rev. 0 | Page 6 of 20
AD71028
Pin No.
40
41
42
43
46
47
48
Mnemonic
CLK27_PA
CLK27_PB
PLL_PA
MCLK_PA
PLL_PB
Input/Output
Description
IN
IN
IN
IN
IN
IN
OUT
Input for 27 MHz Video Reference Clock, Processor A
Input for 27 MHz Video Reference Clock, Processor B
Input from External PLL, Processor A
Clock Input to Processor A
Input from External PLL, Processor B
Clock Input to Processor B
MCLK_PB
DIV1_PA
PLL_PA Clock (Pin 42) Divided by 512 (DOUBLE = 1) or 1024 (DOUBLE = 0)
Rev. 0 | Page 7 of 20
AD71028
FEATURES
MCLK_PA, MCLK_PB
The AD71028 is comprised of two independent digital-input
BTSC encoders. The two processors allow two completely
asynchronous BTSC channels to be encoded, each with its own
clock signals. Figure 1 shows the block diagram of the device.
Master clock inputs. The master clock frequency must be either
256 × fS or 512 × fS, where fS is the input sampling frequency. If
the DOUBLE pin is high, an internal clock doubler is used to
take a 256 × fS input clock and produce the 512 × fS internal
clock required by the DSP core. If the DOUBLE pin is low, the
frequency of the input clock must be set to 512 × fS. In case
these clock signals are not available, a simple external PLL may
be used to generate the master clock signals. On-chip dividers
are provided to simplify this task.
Signal processing parameters are stored in a 256-location
parameter RAM, which is initialized on power-up by an internal
boot ROM. The values stored in the parameter RAM control all
the filter coefficients, mixing, and dynamics processing code
used in the BTSC algorithm.
CDATA
The AD71028 has an SPI port that supports complete read/
write capability of the parameter RAM, as well as a control port
and several other registers that allow the various signal proces-
sing parameters to be controlled. The AD71028 can run as a
standalone processor without SPI control.
Serial data in for the SPI control port. See the SPI Port section
for more information on SPI port timing.
COUT
Serial data output. This is used for reading back registers and
memory locations. It is three-stated when an SPI read is not
active. See the SPI Port section for more information on SPI
port timing.
The AD71028 has a very flexible serial data input port that
allows for glueless interconnection to a variety of signal sources.
The AD71028 can be configured in left-justified, I2S, right-
justified, or DSP serial port compatible modes. It can support
16, 20, and 24 bits in all modes. The AD71028 accepts serial
audio data in MSB first, twos complement format.
CCLK
SPI bit-rate clock. This pin may either run continuously or be
gated in between SPI transactions. See the SPI Port section for
more information on SPI port timing.
The AD71028 operates from a single 5 V power supply. It is fab-
ricated on a single monolithic integrated circuit and is housed
in a 48-lead LQFP package for operation over the 0°C to 70°C
temperature range.
CLATCH
SPI latch signal. This signal must go low at the beginning of an
SPI transaction and high at the end of a transaction. Each SPI
transaction may take a different number of CCLKs to complete,
depending on the address and read/write bit that are sent at the
beginning of the SPI transaction. Detailed SPI timing informa-
tion can be found in the SPI Port section.
PIN FUNCTIONS
Pin names and functions are shown below. Note that pins with a
“_PA” designation are connected to Processor A, while those
with a “_PB” designation are connected to Processor B. All input
pins have a logic threshold compatible with TTL input levels,
and may therefore be used in systems with 3.3 V logic. All
digital output levels are controlled by the ODVDD pin, which
may range from 2.7 V to 5.5 V, for compatibility with a wide
range of external devices.
RESETB
Active-low reset signal. After RESETB transitions from low to
high, the AD71028 goes through an initialization sequence
where the parameter RAMs are initialized with the contents of
the on-board boot ROM. All SPI registers are set to 0, and the
data RAMs are also zeroed. The initialization is complete after
1024 MCLK cycles. New values should not be written to the SPI
port until the initialization is complete.
LRCLK_PA, LRCLK_PB
Left/right clocks for framing the input data. The interpretation
of the LRCLK changes according to the serial mode, set by
writing to the control registers.
DOUBLE
BCLK_PA, BCLK_PB
When this pin is set high, the internal clock doubler is turned
on so a 256 × fS MCLK can be input to the AD71028.
Serial bit clocks for clocking in the serial data. The interpreta-
tion of BCLK changes according to the serial mode, which is set
by writing to the control registers.
PLL_PA, PLL_PB
PLL clock input pins for Processor A and Processor B. These
pins are connected to an internal divide-by-1024 circuit (or
divide-by-512 if DOUBLE is high). This makes it possible to use
an inexpensive external PLL to generate the system clock. If an
external PLL is used, this pin should also be connected to the
appropriate MCLK_PA or MCLK_PB pin.
SDATA_PA, SDATA_PB
Serial data inputs to each processor. The serial format is selected
by writing to Bits <3:0> of the control registers.
Rev. 0 | Page 8 of 20
AD71028
CLK27_PA, CLK27_PB
DVDD
Input pins to the divide-by-1125 block. If an external PLL is
used to generate the audio master clock, the 27 MHz video
master clock may be applied to these pins where it is divided by
1125 to produce a 24 kHz feedback clock to the external PLL
phase detector.
Digital VDD for core. 5 V nominal.
ODVDD
Digital VDD for all digital outputs. Variable from 2.7 V to 5.5 V.
DGND
Digital ground.
AVDD
DIV1_PA, DIV1_PB
Output of divide-by-1024 circuit. Divides the master clock
signal by 1024 (or 512 when DOUBLE is asserted). Used to
interface to external PLL.
Analog VDD. 5 V nominal. Bypass capacitors should be placed
close to the pins and connected directly to the analog ground
plane.
DIV2_PA, DIV2_PB
AGND
Output of divide-by-1125 circuit. Divides the master-clock
signal by 1125. Used to interface to external PLL. The output
signal is a pulse with a duration of one master clock, and should
therefore be used with edge-triggered phase detectors.
Analog ground.
OUTA+, OUTA–
Differential analog outputs for Processor A. The nominal output
voltage for a 1 kHz 0 dB mono input signal is 600 mV rms. This
level may be adjusted by writing to SPI location 258.
REFCAP
Analog reference voltage input. The nominal REFCAP input
voltage is 2.5 V; the analog gain scales directly with the voltage
on this pin. Any ac signal on this pin will cause distortion, and
therefore a large decoupling capacitor should be used to ensure
that the voltage on REFCAP is clean. The input impedance of
REFCAP is greater than 1 MΩ.
OUTB+, OUTB–
Differential analog outputs for Processor B. The nominal output
voltage for a 1 kHz 0 dB mono input signal is 600 mV rms. This
level may be adjusted by writing to SPI location 770.
FILTCAP
Filter cap point. This pin is used to reduce the noise on an
internal biasing point in order to provide the highest
performance. It may not be necessary to connect this pin,
depending on the quality of the layout and grounding used in
the application circuit.
Rev. 0 | Page 9 of 20
AD71028
SIGNAL PROCESSING
L – R
COMPRESSOR
L
TO
DAC
2× Fh CARRIER
OSCILLATOR
MATRIX
L + R
Fh PILOT
R
75µs
PRE-EMPHASIS
FILTER
Figure 3. Signal Processing Flow
BACKGROUND OF BTSC
PERFORMANCE FACTORS
BTSC is the name of the standard for adding stereo audio
capability to the US television system. It is in many ways similar
to the algorithm used for FM stereo broadcasts, with the
addition of a sophisticated compressor circuit to improve the
signal-to-noise ratio.
In order to maintain good separation between left and right, it is
necessary to closely match the filtering and companding stan-
dards set forth in the standard (FCC OET60). Even small errors
can result in poor performance. The AD71028 has been pro-
grammed to match these standards as accurately as possible.
Separation typically ranges from 30 dB at frequencies below
1 kHz to 15 dB at 14 kHz. Measuring these numbers can be
difficult as significant differences exist between many so-called
reference decoders, which are all implemented with analog
components.
The processing of mono (L = R) signals is unchanged from the
original pre-BTSC system in order to maintain compatibility
with non-BTSC TV receivers. The L + R signal is applied to a
75 µs pre-emphasis filter, and is then applied to a 4.5 MHz FM
modulator, which is later added into the video signal to create a
composite video signal.
SEPARATION ALIGNMENT
The BTSC encoder outputs are all specified in terms of the
deviation of the FM 4.5 MHz carrier. For the AD71028, a digital
input level of 0 dB (mono signal) should cause a carrier
deviation of 25 kHz without the 75 µs pre-emphasis filter. In
practice, the pre-emphasis filter may be left in for this adjust-
ment, as long as the frequency is low enough to not be affected
by the pre-emphasis filter. It is critical to maintain the proper
gain relationship between the BTSC encoder and the 4.5 MHz
FM modulator. A common mistake is to assume that changing
the gain between the BTSC encoder output and the FM
modulator input has the same effect as changing the audio
input level going in to the BTSC encoder. The presence of a
complicated 2-band nonlinear dynamics processor means that
the encoder output must be connected to the decoder input
(through the FM modulation/demodulation process) with a
known gain. If this gain is changed, the separation will
significantly suffer.
Stereo capability is added by taking the L–R signal, applying it
to a 2-band dynamic compressor, and then multiplying this
signal by a carrier signal at twice the horizontal scanning rate
(Fh), or about 2 × 15.734 kHz. This multiplication is known as
double-sideband suppressed-carrier modulation, and it
effectively translates the compressed L – R spectrum up in
frequency so that it sits above the audio band (Figure 3).
In order for the receiver to recover this L – R signal, a pilot tone
at the horizontal rate is added to the signal. The receiver has a
PLL that locks to this pilot and generates a signal at the carrier
frequency. This signal is then used to multiply the composite
BTSC-encoded signal, which translates this component back
down to baseband. The L – R signal is then applied to a 2-band
expander, which is the complement to the earlier compressor
step. Once the L + R and L – R signals are recovered, a simple
addition/subtraction circuit (sometimes referred to as the
“matrix”) can be used to recover the L and R signal.
When measuring the AD71028 on the bench, it is possible to
use a BTSC reference decoder box, so that the FM modulation/
demodulation process may be skipped. These units have a
method of adjusting the input voltage sensitivity to achieve best
separation. The output level of the AD71028 can also be
adjusted over a wide range using either the SPI control port or
by adjusting the values of the components used in the external
analog low-pass filter that is between the BTSC encoder output
and the input to the FM modulator.
Since the pilot tone is added at 15.734 kHz, it is necessary to
reduce the signal’s bandwidth so that audio signals cannot
interfere with the pilot tone. In the AD71028, the bandwidth is
limited to 14 kHz; above this frequency, the response decays
very rapidly.
Rev. 0 | Page 10 of 20
AD71028
The AD71028 contains a clock doubler circuit that may be used
to generate an internal 512 × fS clock when the external clock is
256 × fS. The clock mode is set by connecting the DOUBLE pin
either high or low. This pin should be tied either high or low
and should not be changed after power-up.
PHASE LINEARITY OF THE EXTERNAL ANALOG
FILTER
If the time alignment of the pilot to the carrier signal is not
close to 0 degrees, a loss of separation can occur. This means
that the external analog low-pass filter should be a linear-phase
design to provide constant group delay over the range from dc
to 50 kHz. Bessel filters are recommended for this application.
Figure 12 shows a recommended design for these filters.
The AD71028 requires a master clock at either 256 × 48 kHz
(12.288 MHz) when DOUBLE = 1 or 512 × 48 kHz
(24.576 MHz) when DOUBLE = 0. In some cases, this signal is
provided by the MPEG decoder chip itself. In other cases, only
the 27 MHz video clock may be available. In this case, the
AD71028 provides on-chip dividers to interface to an external
PLL such as the 74HC4046. Figure 4 shows the circuit to
accomplish this. The 27 MHz clock is applied to the AD71028
and divided down by 1125, producing a signal at 24 kHz. The
PLL oscillator output is divided down by 512, producing a
24 kHz output (when locked). These two signals are applied to
the phase-comparator inputs of the external PLL. Note that the
divided-down 27 MHz signal looks like a pulse with a duration
of one master clock, and therefore only edge-triggered phase
detectors should be used.
INPUT LEVELS
The maximum input level to the AD71028 changes across
frequency. Table 10 shows the maximum allowable input level
for different frequencies. These values are part of the BTSC
specification and are not a function of this chip.
Table 10. Maximum Input Levels to the BTSC Encoder
across Frequency
Frequency (Hz)
20 to 1000
1600
2500
3150
5000
8000
12500
Maximum Input Level (dBFS)
0 dB
–1 dB
–3 dB
–5 dB
–8 dB
–11 dB
–15 dB
AD71028
27MHz IN
DIVIDE-BY-1125
DIVIDE-BY-512
74HC4046
CLOCK RELATIONSHIPS
In an MPEG receiver architecture, all clocks are typically
generated from a 27 MHz master clock. The following integer
relationships are found between the clocks, with Fh =
15.734 kHz:
DSP
a) 27 MHz/Fh = 1716 = 2 × 2 × 3 × 11 × 13
b) Fh/2 = Fcolor_subcarrier/(5 × 7 × 13)
Figure 4. PLL Connections for 27 MHz Master Clock
c) 27 MHz/Fcolor_subcarrier = (5 × 7)/(2 × 2 × 2 × 3 × 11)
d) 27 MHz/48 kHz = 1125/2
Rev. 0 | Page 11 of 20
AD71028
SPI PORT
CLATCH
CCLK
BYTE 1
BYTE 4
BYTE 0
CDATA
Figure 5. Sample of SPI Write Format (Single-Write Mode)
CLATCH
CCLK
BYTE 0
HI-Z
BYTE 1
XXX
CDATA
COUT
HI-Z
DATA
DATA
DATA
Figure 6. Sample of SPI Read Format (Single-Read Mode)
COUT signal remains three-stated until a READ operation is
requested. This allows other SPI compatible peripherals to share
the same readback line. All SPI transactions follow the same
basic format, shown in Figure 5. Figure 6 shows the read format.
OVERVIEW
The AD71028 can be controlled using the SPI port. In general,
there are three parameters per processor that can be controlled:
the encoder output level, the Phat Stereo image enhancement
algorithm, and the dialog enhancement algorithm. It is also
possible to write new data into the parameter RAM to alter the
filter coefficients used in the BTSC encoding process. This is a
fairly complex topic unnecessary for normal operation of the
chip, and the details are not included in this data sheet. Please
contact ADI if modifications to the BTSC filters are required.
The Wb/R bit is low for a write and high for a read operation.
The 10-bit address word is decoded into either a location in the
parameter RAM or one of the SPI registers. The number of data
bytes varies according to the register or memory being accessed.
The detailed data format diagram for continuous-mode
operation is given in the SPI Read/Write Data Formats section.
The SPI port uses a 4-wire interface consisting of CLATCH,
CCLK, CDATA, and COUT signals. The CLATCH signal goes
low at the beginning of a transaction and high at the end of a
transaction. The CCLK signal latches the serial input data on a
low-to-high transition. The CDATA signal carries the serial
input data, and the COUT signal is the serial output data. The
SPI ADDRESS DECODING
Table 11 shows the address decoding used in the SPI port. The
SPI address space encompasses a set of registers and the param-
eter RAM. The parameter RAM is loaded on power-up from an
on-board boot ROM.
Table 11. SPI Port Address Decoding
SPI Address
0–255
256
Register Name
Read/Write Word Length
Write: 22 Bits, Read: 22 Bits
Write: 11 Bits, Read: N/A
Parameter RAM Processor A
SPI Control Register Processor A
Reserved
257
258
259
260
512–767
768
Output Level Processor A
Stereo Spreading Control Processor A
Dialog Enhancement Control Processor A
Parameter RAM Processor B
SPI Control Register Processor B
Reserved
Write: 22 Bits, Read: N/A
Write: 22 Bits, Read: N/A
Write: 22 Bits, Read: N/A
Write: 22 Bits, Read: 22 Bits
Write: 22 Bits, Read: N/A
769
770
771
772
Output Level Processor B
Stereo Spreading Control Processor B
Dialog Enhancement Control Processor B
Write: 22 Bits, Read: N/A
Write: 22 Bits, Read: N/A
Write: 22 Bits, Read: N/A
Rev. 0 | Page 12 of 20
AD71028
PARAMETER RAM
OUTPUT LEVEL REGISTER
The parameters for the two BTSC processors are stored in two
256-location RAM spaces. The user should not change most of
these parameters, although editing the dynamics processing
curve for dialog enhancement may be useful if the curve needs
to be changed for a specific application. This is explained in the
Dialog Enhancement Register section of this data sheet.
The output level register controls the overall BTSC output level.
Its default value is –6 dB, which outputs a 600 mV rms reference
level for a 1 kHz 0 dB mono digital input signal. This value is in
2.20 format, and –6 dB corresponds to binary
0010000000000000000000. This register is used in conjunction
with the output filter to match the output BTSC level of the
encoder with the decoder input to achieve maximum separation
values. This level control should not be used to control the
overall volume level of the audio signal.
CONTROL REGISTER
Control Register 1 is an 11-bit register that controls serial
modes, de-emphasis, mute, power-down, and SPI-to-memory
transfers. Table 12 documents the contents of this register.
STEREO ENHANCEMENT REGISTER
This register controls ADI’s patented Phat Stereo spatial
enhancement algorithm. The default is all 0s, which corres-
ponds to no effect. The maximum setting is
Bits 4:5 and 8:10 are reserved and should be set to 0 at all times.
The audio signal is muted with Bit 7 of the control register.
0100000000000000000000, or a twos complement fractional
value of 1.0. Note that the bass energy in each channel is
increased using this algorithm, which may cause some digital
clipping on full-scale signal peaks, especially at low frequencies.
The soft power-down bit (Bit 6) stops the internal clocks to the
DSP core, but does not reset the part. The digital power con-
sumption is reduced to a low level when this bit is asserted.
Reset can only be asserted using the external reset pin.
DIALOG ENHANCEMENT REGISTER
Bits 3:2 select the serial format from one of four modes. These
different formats are discussed in the Initialization section of
this data sheet.
This controls the built-in dialog-enhancement algorithm, and
defaults to 0. The maximum setting is
0100000000000000000000, or a twos complement fractional
value of 1.0. This algorithm is intended to solve the problem of
playing back high dynamic range digital audio signals over a
television’s built-in speakers. It provides an amplitude boost to
signals that are in the range where dialog signals are usually
found, while at the same time preventing loud special effects
passages from overloading the speakers or amplifiers.
The word length bits (1:0) are used in right-justified serial
modes to determine where the MSB is located relative to the
start of the audio frame.
Table 12. Control Register Contents
Register Bits
Function
10
9
8
7
6
Reserved, Set to 0
Reserved, Set to 0
Reserved, Set to 0
Soft Mute (1 = Start Mute Sequence)
Soft Power-Down (1 = Power-Down)
Reserved, Set to 00
Serial In Mode
The dialog enhancement control is set up as a dynamics
processing curve with 33 locations on the curve, each spaced
3 dB apart. There is a default dialog enhancement curve that is
set at power-up, but this can be changed if a different curve is
desired. The curve ranges from an rms input level of –87 dB on
the low end to +9 dB on the high end. The value corresponding
to each point in the parameter RAM represents a gain at the
appropriate input level. This gain value should range from 0
(–∞ dB) to +2.0 – 1 LSB (approximately +6 dB). The gain at a
–87 dB input corresponds to parameter RAM location 4 on
Processor A and location 516 on Processor B. The table extends
to the +9 dB input gain at locations 36 and 548 for Processors A
and B, respectively.
5:4
3:2
00 = I2S
01 = Right-Justified
10 = DSP
11 = Left-Justified
Word Length
1:0
00 = 24 Bits
01 = 20 Bits
10 = 16 Bits
11 = 16 Bits
Rev. 0 | Page 13 of 20
AD71028
Table 13. SPI Control Register 1 Write format
Byte 0
Byte 1
Byte 2
Byte 3
00000, Wb/R, Adr [9:8]
Adr [7:0]
00000, Bit [10:8]
Bit [7:0]
Table 14. SPI Write Format for Parameter RAM, Output Level, Stereo Spreading and Dialog Enhancement Registers
Byte 0
Byte1
Byte 2
Byte 3
Byte 4
000000, Adr [9:8]
Adr [7:0]
00, Level [21:16]
Level [15:8]
Level [7:0]
Serial Data Input Modes
SPI READ/WRITE DATA FORMATS
Figure 7 shows the left-justified mode. LRCLK is high for the
left channel and low for the right channel. Data is sampled on
the rising edge of BCLK. The MSB is left-justified to a LRCLK
transition with no MSB delay. The left-justified mode can accept
any word length up to 24 bits.
The read/write formats of the SPI port are designed to be byte-
oriented. This allows for easy programming of common micro-
controller chips. In order to fit into a byte-oriented format, 0s
are appended to the data fields in order to extend the data-word
to the next multiple of 8 bits. For example, 22-bit words written
to the SPI parameter RAM are appended with two leading zeros
in order to reach 24 bits (3 bytes). These zero-extended data
fields are appended to a 2-byte field consisting of a read/write
bit and a 10-bit address. The SPI port knows how many data
bytes to expect based on the address that is received in the first
2 bytes.
Figure 8 shows the I2S mode, which is the default setting.
LRCLK is low for the left channel, and the MSB is delayed from
the edge of the LRCLK by a single BCLK period. The I2S mode
can be used to accept any number of bits up to 24.
Figure 9 shows the AD71028’s right-justified mode. LRCLK is
high for the left channel and low for the right channel. Data is
sampled on the rising edge of BCLK. The start of data is delayed
from the LRCLK edge by 16, 12, or 8 BCLK intervals, depending
on the selected word length. The default word length is 24 bits;
other word lengths are set by writing to Bits <1:0> of the control
register. In right-justified mode, it is assumed that there are 64
BCLKs per frame.
INITIALIZATION
Power-Up Sequence
The AD71028 has a built-in power-up sequence that initializes
the contents of all internal RAM. During this time, the SPI
parameter RAM is filled with values from its associated boot
ROM. The data memories are also cleared during this time.
The boot sequence lasts for 1024 MCLK cycles and starts on the
rising edge of the RESETB pin. The user should avoid writing to
or reading from the SPI registers during this period of time.
Figure 10 shows the DSP serial port mode. LRCLK must pulse
high for at least one bit clock period before the MSB of the left
channel is valid, and LRCLK must pulse high again for at least
one bit clock period before the MSB of the right channel is
valid. Data is sampled on the falling edge of BCLK. The DSP
serial port mode can be used with any word length up to 24 bits.
In this mode, it is the responsibility of the DSP to ensure that
the left data is transmitted with the first LRCLK pulse, and that
synchronism is maintained from that point forward.
SERIAL DATA INPUT PORT
The AD71028’s flexible serial data input port accepts data in
twos complement, MSB-first format. The left channel data field
always precedes the right channel data field. The serial mode is
set by using mode select bits in the SPI control register. In all
modes except the right-justified mode, the serial port will
accept an arbitrary number of bits up to a limit of 24 (extra bits
will not cause an error, but they will be truncated internally). In
right-justified mode, SPI control register bits are used to set the
word length to 16, 20, or 24 bits. The default on power-up is
24-bit mode. Proper operation of the right-justified mode
requires that there be exactly 64 BCLKs per audio frame.
Rev. 0 | Page 14 of 20
AD71028
RIGHT CHANNEL
LEFT CHANNEL
LRCLK
BCLK
MSB
LSB
MSB
LSB
SDATA
1 /F
S
Figure 7. Left-Justified Mode—16 Bits to 24 Bits per Channel
LEFT CHANNEL
LRCLK
RIGHT CHANNEL
BCLK
LSB
MSB
SDATA
MSB
LSB
1 /F
S
Figure 8. I2S Mode—16 Bits to 24 Bits per Channel
RIGHT CHANNEL
LEFT CHANNEL
LRCLK
BCLK
SDATA
MSB
LSB
1 /F
MSB
LSB
S
Figure 9. Right-Justified Mode—16 Bits to 24 Bits per Channel
LRCLK
BCLK
MSB
MSB
LSB
LSB
SDAT
A
1 /F
S
Figure 10. DSP Mode—16 Bits to 24 Bits per Channel
NOTES
1. DSP mode does not identify the channel.
2. LRCLK normally operates at FS; in DSP mode, LRCLK operates at 2 × FS.
3. BCLK frequency is normally 64 × LRCLK but may be operated in burst mode.
Rev. 0 | Page 15 of 20
AD71028
ANALOG OUTPUT SECTION
Figure 11 shows the block diagram of the analog output section
(one of two channels). A series of current sources is controlled
by a digital Σ-∆ modulator. Depending on the digital code from
the modulator, each current source is connected to the sum-
ming junction of either a positive I-to-V converter or a negative
I-to-V converter. Two extra current sources that push instead of
pull are added to set the midscale common-mode voltage.
Since the VREF input effectively multiplies the signal, care must
be taken to ensure that no ac signals appear on this pin. This
can be accomplished by using a large decoupling capacitor in
the VREF external resistive divider circuit. If the VREF signal is
derived by dividing the 5 V analog supply, the time constant of
the divider must effectively filter any noise on the supply. If the
VREF signal is derived from an unregulated power amplifier
supply, the time constant must be longer because the ripple on
the amplifier supply voltage will presumably be greater than in
the case of the 5 V supply.
All current sources are derived from the VREF input pin. The
gain of the AD71028 is directly proportional to the magnitude
of the current sources, and therefore the gain of the AD71028 is
proportional to the voltage on the VREF pin. The nominal
VREF voltage should be set to 2.5 V, using a simple resistive
divider from the analog supply. The VREF and biasing circuits
are common to both DACs.
The AD71028 should be used with an external third-order filter
on each output channel. The circuit shown in Figure 12
combines a third-order filter and a single-ended-to-differential
converter in the same circuit. The values shown are for a
100 kHz Bessel filter. The use of a Bessel filter is important to
maintain the time alignment of the pilot to the carrier. If these
signals are not in phase, a loss of separation will occur.
I
I
REF
REF
The outputs can also be used single-ended, with some loss of
performance; the DAC distortion may become significantly
poorer, although the SNR will remain quite high.
OUT+
OUT–
V
IN
REF
For best performance, a large (>10 µF) capacitor should be
connected between the FILTCAP pin and analog ground.
I
+ DIG_IN
I
– DIG_IN
REF
REF
BIAS
FROM DIGITAL
Σ–∆ MODULATOR
(DIG_IN)
SWITCHED CURRENT
SOURCES
3.01kΩ
1.50kΩ
270pF
2.80kΩ
1nF
–INPUT
+INPUT
549Ω
OUT
Figure 11. Internal DAC Analog Architecture
2.7nF
806Ω
2.2nF
499kΩ
1.00kΩ
820pF
Figure 12. Recommended External Analog Filter for Each Channel
Rev. 0 | Page 16 of 20
AD71028
OUTLINE DIMENSIONS
0.75
0.60
0.45
9.00 BSC
SQ
1.60
MAX
37
48
36
1
PIN 1
SEATING
PLANE
10°
6°
2°
ꢀ
7.00
BSC SQ
TOP VIEW
(PINS DOWN)
1.45
1.40
1.35
0.20
0.09
VIEW A
7°
3.5
0°
25
12
°
13
24
0.15
0.05
SEATING
PLANE
0.27
0.22
0.17
0.08 MAX
COPLANARITY
0.50
BSC
VIEW A
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026BBC
Figure 13. 48-Lead Low Profile Quad Flatpack [LQFP]
(ST-48)
Dimensions Shown in Millimeters
ORDERING GUIDE
Model
AD71028JST
Temperature Range
–0°C to +70°C
Package Description
48-Lead LQFP
Package Option
ST-48
AD71028JSTRL
–0°C to +70°C
48-Lead LQFP
ST-48 on 13” Reel
Rev. 0 | Page 17 of 20
AD71028
NOTES
Rev. 0 | Page 18 of 20
AD71028
NOTES
Rev. 0 | Page 19 of 20
AD71028
NOTES
© 2004 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D04482–0–1/04(0)
Rev. 0 | Page 20 of 20
相关型号：
AD7111ABCHIPS
IC PARALLEL, 8 BITS INPUT LOADING, 8-BIT DAC, UUC, DIE, Digital to Analog Converter
ADI
©2020 ICPDF网 联系我们和版权申明