AD7226KPZ-REEL [ADI]
LC2MOS Quad 8-Bit D/A Converter; LC2MOS四通道8位D / A转换器
| 型号： | AD7226KPZ-REEL |
| 厂家： | 
ADI |
| 描述： | LC2MOS Quad 8-Bit D/A Converter |
| 文件： | 总16页 (文件大小：423K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LC2MOS
Quad 8-Bit D/A Converter
AD7226
FEATURES
FUNCTIONAL BLOCK DIAGRAM
Four 8-Bit DACs with Output Amplifiers
Skinny 20-Lead DIP, SOIC, SSOP, and PLCC Packages
Microprocessor-Compatible
TTL/CMOS-Compatible
V
V
DD
REF
No User Trims
Extended Temperature Range Operation
Single Supply Operation Possible
A
V
A
LATCH A
LATCH B
LATCH C
LATCH D
OUT
DAC A
DAC B
DAC C
DAC D
D
A
T
B
V
B
C
OUT
APPLICATIONS
Process Control
Automatic Test Equipment
Automatic Calibration of Large System Parameters,
e.g., Gain/Offset
MSB
DATA
(8-BIT)
A
B
U
S
LSB
V
V
C
D
OUT
D
OUT
WR
A1
CONTROL
LOGIC
AD7226
A0
V
AGND
AGND
SS
GENERAL DESCRIPTION
PRODUCT HIGHLIGHTS
The AD7226 contains four 8-bit voltage-output digital-to-
analog converters, with output buffer amplifiers and interface
logic on a single monolithic chip. No external trims are required
to achieve full specified performance for the part.
1. DAC-to-DAC Matching
Since all four DACs are fabricated on the same chip at the
same time, precise matching and tracking between the DACs
is inherent.
Separate on-chip latches are provided for each of the four D/A
converters. Data is transferred into one of these data latches
through a common 8-bit TTL/CMOS (5 V) compatible input
port. Control inputs A0 and A1 determine which DAC is
loaded when WR goes low. The control logic is speed-compat-
ible with most 8-bit microprocessors.
2. Single-Supply Operation
The voltage mode configuration of the DACs allows the
AD7226 to be operated from a single power supply rail.
3. Microprocessor Compatibility
The AD7226 has a common 8-bit data bus with individual
DAC latches, providing a versatile control architecture for
simple interface to microprocessors. All latch enable signals
are level triggered.
Each D/A converter includes an output buffer amplifier capable
of driving up to 5 mA of output current. The amplifiers’ offsets
are laser-trimmed during manufacture, thereby eliminating any
requirement for offset nulling.
4. Small Size
Combining four DACs and four op amps plus interface logic
into a 20-pin package allows a dramatic reduction in board
space requirements and offers increased reliability in systems
using multiple converters. Its pinout is aimed at optimizing
board layout with all the analog inputs and outputs at one
end of the package and all the digital inputs at the other.
Specified performance is guaranteed for input reference voltages
from 2 V to 12.5 V with dual supplies. The part is also specified
for single supply operation at a reference of 10 V.
The AD7226 is fabricated in an all ion-implanted high speed
Linear Compatible CMOS (LC2MOS) process, which has been
specifically developed to allow high speed digital logic circuits
and precision analog circuits to be integrated on the same chip.
REV.
D
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, norforanyinfringementsofpatentsorotherrightsofthirdpartiesthat
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective companies.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
781-461-3113
Fax:
© 2011 Analog Devices, Inc. All rights reserved.
(VDD = 11.4 V to 16.5 V, VSS = –5 V ꢀ 10%, AGND = DGND = 0 V; VREF = +2 V to (VDD – 4 V)1,
unless otherwise noted. All Specifications TMIN to TMAX unless otherwise noted.)
AD7226–SPECIFICATIONS
DUAL SUPPLY
Parameter
K, B Versions2
Unit
Conditions/Comments
STATIC PERFORMANCE
Resolution
Total Unadjusted Error
Relative Accuracy
Differential Nonlinearity
Full-Scale Error
Full-Scale Temperature Coefficient
Zero Code Error
8
±1
±0.5
±1
±0.5
±20
±20
Bits
LSB max
LSB max
LSB max
LSB max
ppm/∞C typ
mV max
mV/∞C typ
VDD = 15 V ± 5%, VREF = 10 V
Guaranteed Monotonic
VDD = 14 V to 16.5 V, VREF = +10 V
Zero Code Error Temperature Coefficient ±50
REFERENCE INPUT
Voltage Range
2 to (VDD – 4)
2
50
200
V min to V max
kW min
Input Resistance
Input Capacitance3
pF min
Occurs when each DAC is loaded with all 0s.
Occurs when each DAC is loaded with all 1s.
pF max
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Leakage Current
Input Capacitance
2.4
0.8
±1
V min
V max
mA max
pF max
V
IN = 0 V or VDD
8
Input Coding
Binary
DYNAMIC PERFORMANCE
Voltage Output Slew Rate4
Voltage Output Settling Time4
Digital Crosstalk
2.5
4
10
2
V/ms min
ms max
nV secs typ
kW min
VREF = 10 V; Settling Time to ±1/2 LSB
Minimum Load Resistance
VOUT = 10 V
POWER SUPPLIES
VDD Range
IDD
ISS
11.4/16.5
13
11
V min/V max
mA max
mA max
For Specified Performance
Outputs Unloaded; VIN = VINL or VINH
Outputs Unloaded; VIN = VINL or VINH
SWITCHING CHARACTERISTICS4, 5
Address to Write Setup Time, tAS
Address to Write Hold Time, tAH
Data Valid to Write Setup Time, tDS
Data Valid to Write Hold Time, tDH
Write Pulsewidth, tWR
0
0
50
0
50
ns min
ns min
ns min
ns min
ns min
NOTES
1Maximum possible reference voltage.
2Temperature ranges are as follows:
K Version: –40∞C to +85∞C
B Version: –40∞C to +85∞C
3Guaranteed by design. Not production tested.
4Sample Tested at 25∞C to ensure compliance.
5Switching Characteristics apply for single and dual supply operation.
Specifications subject to change without notice.
–2–
REV. D
AD7226
(VDD = 15 V ꢀ 5%, VSS = AGND = DGND = O V; VREF = 10 V1 unless otherwise noted.
All specifications TMIN to TMAX unless otherwise noted.)
SINGLE SUPPLY
Parameter
K, B Versions2
Unit
Conditions/Comments
STATIC PERFORMANCE
Resolution
Total Unadjusted Error
Differential Nonlinearity
8
±2
±1
Bits
LSB max
LSB max
Guaranteed Monotonic
REFERENCE INPUT
Input Resistance
2
50
200
kW min
pF min
pF max
Input Capacitance3
Occurs when each DAC is loaded with all 0s.
Occurs when each DAC is loaded with all 1s.
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Leakage Current
Input Capacitance
2.4
0.8
±1
V min
V max
mA max
pF max
V
IN = 0 V or VDD
8
Input Coding
Binary
DYNAMIC PERFORMANCE
Voltage Output Slew Rate4
Voltage Output Settling Time4
Digital Crosstalk
2
4
10
2
V/ms min
ms max
nV secs typ
kW min
Settling Time to ±1/2 LSB
Minimum Load Resistance
VOUT = +10 V
POWER SUPPLIES
V
DD Range
14.25/15.75
13
V min/V max
mA max
For Specified Performance
Outputs Unloaded; VIN = VINL or VINH
IDD
NOTES
1Maximum possible reference voltage.
2Temperature ranges are as follows:
K Version: –40∞C to +85∞C
ABSOLUTE MAXIMUM RATINGS1
VDD to AGND . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V, +17 V
VDD to DGND . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V, +17 V
VSS to AGND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –7 V, VDD
VSS to DGND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –7 V, VDD
VDD to VSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V, +24 V
AGND to DGND . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V, VDD
Digital Input Voltage to DGND . . . . . . . –0.3 V, VDD + 0.3 V
VREF to AGND . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V, VDD
VOUT to AGND2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . VSS, VDD
Power Dissipation (Any Package) to 75∞C . . . . . . . . . . 500 mW
Derates above 75∞C by . . . . . . . . . . . . . . . . . . . . . 2.0 mW/∞C
Operating Temperature
B Version: –40∞C to +85∞C
3Guaranteed by design. Not production tested.
4Sample Tested at 25∞C to ensure compliance.
Specifications subject to change without notice.
Commercial (K Version) . . . . . . . . . . . . . . . –40∞C to +85∞C
Industrial (B Version) . . . . . . . . . . . . . . . . . –40∞C to +85∞C
Storage Temperature . . . . . . . . . . . . . . . . . . . –65∞C to +150∞C
Lead Temperature (Soldering, 10 secs) . . . . . . . . . . . . . 300∞C
NOTES
1Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only, functional operation of the
device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2Outputs may be shorted to AGND provided that the power dissipation of the
package is not exceeded. Typically short circuit current to AGND is 50 mA.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although the
AD7226 features proprietary ESD protection circuitry, permanent damage may occur on devices
subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended
to avoid performance degradation or loss of functionality.
REV. D
–3–
AD7226
PIN CONFIGURATIONS
DIP and SOIC/SSOP
V
V
B
A
1
2
3
4
5
6
7
8
9
20
19
18
17
16
V
V
V
C
D
OUT
OUT
OUT
DD
OUT
V
SS
A0
A1
V
REF
AGND
DGND
AD7226
TOP VIEW
(Not to Scale)
15 WR
14
DB0(LSB)
DB7 (MSB)
DB6
13 DB1
12
11
DB2
DB3
DB5
DB4 10
PLCC
3
2
1
20 19
4
5
6
7
8
18
V
DD
V
REF
17 A0
16 A1
AGND
DGND
AD7226
TOP VIEW
(Not to Scale)
15
WR
DB7 (MSB)
DB8
14 DB0(LSB)
9
10 11 12 13
TERMINOLOGY
DIFFERENTIAL NONLINEARITY
Differential Nonlinearity is the difference between the measured
change and the ideal 1 LSB change between any two adjacent
codes. A specified differential nonlinearity of ±1 LSB max over
the operating temperature range ensures monotonicity.
TOTAL UNADJUSTED ERROR
This is a comprehensive specification that includes full-scale
error, relative accuracy and zero code error. Maximum output
voltage is VREF – 1 LSB (ideal), where 1 LSB (ideal) is VREF
/
256. The LSB size will vary over the VREF range. Hence the zero
code error will, relative to the LSB size, increase as VREF decreases.
Accordingly, the total unadjusted error, which includes the zero
code error, will also vary in terms of LSB’s over the VREF range.
As a result, total unadjusted error is specified for a fixed refer-
ence voltage of 10 V.
DIGITAL CROSSTALK
The glitch impulse transferred to the output of one converter
due to a change in the digital input code to another of the con-
verters. It is specified in nV secs and is measured at VREF = 0 V.
FULL SCALE ERROR
Full-Scale Error is defined as:
RELATIVE ACCURACY
Measured Value – Zero Code Error – Ideal Value
Relative Accuracy or endpoint nonlinearity, is a measure of the
maximum deviation from a straight line passing through the
endpoints of the DAC transfer function. It is measured after
allowing for zero and full-scale error and is normally expressed
in LSB’s or as a percentage of full-scale reading.
–4–
REV. D
AD7226
CIRCUIT INFORMATION
D/A SECTION
In single supply operation (VSS = 0 V = AGND), with the out-
put approaching AGND (i.e., digital code approaching all 0s)
The AD7226 contains four identical, 8-bit, voltage mode digital-to-
analog converters. The output voltages from the converters have the
same polarity as the reference voltage allowing single supply opera-
tion. A novel DAC switch pair arrangement on the AD7226 allows a
reference voltage range from 2 V to 12.5 V.
V
DD
I/P
Each DAC consists of a highly stable, thin-film, R-2R ladder
and eight high speed NMOS, single-pole, double-throw
switches. The simplified circuit diagram for one channel is
shown in Figure 1. Note that VREF (Pin 4) and AGND (Pin 5)
are common to all four DACs.
O/P
400ꢁA
V
SS
Figure 2. Amplifier Output Stage
R
R
R
V
OUT
the current load ceases to act as a current sink and begins to act
as a resistive load of approximately 2 kW to AGND. This occurs
as the NMOS transistors come out of saturation. This means
that, in single supply operation, the sink capability of the ampli-
fiers is reduced when the output voltage is at or near AGND. A
typical plot of the variation of current sink capability with out-
put voltage is shown in Figure 3.
2R
2R
DB0
2R
DB5
2R
DB6
2R
DB7
V
REF
AGND
SHOWN FOR ALL 1s ON DAC
500
Figure 1. D/A Simplified Circuit Diagram
The input impedance at the VREF pin of the AD7226 is the
V
= –5V
SS
400
300
parallel combination of the four individual DAC reference input
impedances. It is code dependent and can vary from 2 kW to
infinity. The lowest input impedance (i.e., 2 KW) occurs when
all four DACs are loaded with the digital code 01010101.
Therefore, it is important that the reference presents a low
output impedance under changing load conditions. The nodal
capacitance at the reference terminals is also code dependent
and typically varies from 100 pF to 250 pF.
V = +15V
DD
V
= 0
SS
200
100
0
Each VOUT pin can be considered as a digitally programmable
voltage source with an output voltage of:
(1)
VOUTX = DX VREF
0
2
4
6
8
10
V
(V)
OUT
where DX is fractional representation of the digital input code
and can vary from 0 to 255/256.
Figure 3. Variation of ISINK with VOUT
If the full sink capability is required with output voltages at or
near AGND (= 0 V), then VSS can be brought below 0 V by 5 V
and thereby maintain the 400 mA current sink as indicated in
Figure 3. Biasing VSS below 0 V also gives additional headroom
in the output amplifier which allows for better zero code error
performance on each output. Also improved is the slew rate and
negative-going settling time of the amplifiers (discussed later).
The source impedance is the output resistance of the buffer
amplifier.
OP AMP SECTION
Each voltage-mode D/A converter output is buffered by a unity
gain, noninverting CMOS amplifier. This buffer amplifier is
capable of developing 10 V across a 2 kW load and can drive
capacitive loads of 3300 pF. The output stage of this amplifier
consists of a bipolar transistor from the VDD line and a current
load to the VSS, the negative supply for the output amplifiers.
This output stage is shown in Figure 2.
Each amplifier offset is laser trimmed during manufacture to
eliminate any requirement for offset nulling.
DIGITAL SECTION
The digital inputs of the AD7226 are both TTL and CMOS
(5 V) compatible from VDD = 11.4 V to 16.5 V. All logic inputs
are static protected MOS gates with typical input currents of
less than 1 nA. Internal input protection is achieved by an
on-chip distributed diode from DGND to each MOS gate. To
minimize power supply currents, it is recommended that the
digital input voltages be driven as close to the supply rails (VDD
and DGND) as practically possible.
The NPN transistor supplies the required output current drive
(up to 5 mA). The current load consists of NMOS transistors
which normally act as a constant current sink of 400 mA to VSS,
giving each output a current sink capability of approximately
400 mA if required.
The AD7226 can be operated single or dual supply resulting
in different performance in some parameters from the output
amplifiers.
D
REV.
–5–
AD7226
INTERFACE LOGIC INFORMATION
A0
A1
Address lines A0 and A1 select which DAC will accept data
from the input port. Table I shows the selection table for the
four DACs with Figure 4 showing the input control logic. When
the WR signal is LOW, the input latches of the selected DAC
are transparent and its output responds to activity on the data
bus. The data is latched into the addressed DAC latch on the
rising edge of WR. While WR is high the analog outputs remain
at the value corresponding to the data held in their respective latches.
TO LATCH A
TO LATCH B
TO LATCH C
TO LATCH D
WR
Table I. AD7226 Truth Table
AD7226 Control Inputs AD7226
Figure 4. Input Control Logic
WR
A1
A0
Operation
tDS
tDH
H
L
X
L
L
X
L
L
No Operation Device Not Selected
DAC A Transparent
DAC A Latched
V
DD
V
INH
DATA
V
INL
0
L
L
L
L
L
H
H
H
H
H
H
L
L
H
H
DAC B Transparent
DAC B Latched
DAC C Transparent
DAC C Latched
DAC D Transparent
DAC D Latched
tAH
tAS
V
V
DD
INH
ADDRESS
V
INL
0
tWR
V
WR
DD
L = Low State, H = High State, X = Don’t Care
0
NOTES
1. ALL INPUT SIGNAL RISE AND FALL TIMES
MEASURED FROM 10% TO 90% OF V
.
DD
tr
= tf = 20ns OVER V RANGE.
DD
2. TIMING MEASUREMENT REFERENCE LEVEL IS
V
+ V
2
INH
INL
3. SELECTED INPUT LATCH IS TRANSPARENT WHILE WR IS
LOW, THUS INVALID DATA DURING THIS TIME CAN CAUSE
SPURIOUS OUTPUTS.
Figure 5. Write Cycle Timing Diagram
–6–
REV. D
Typical Performance Characteristics–AD7226
(TA = 25ꢂC, VDD = 15 V, VSS = –5 V)
AD7226K, B
2.0
1.5
1.0
0.5
4
3
2
V
= 10V
REF
1
0
–0.5
–1.0
–1.5
–2.0
0
–1
–2
–3
–4
16 32 48 64 80 96 112 128 144 160 176 192 208 224 240 256
INPUT CODE (DECIMAL EQUIVALENT)
0
0
2
4
6
V
8
(V)
10
12
14
REF
TPC 1. Channel-to-Channel Matching
TPC 3. Differential Nonlinearity vs. VREF
AD7226K, B
4
3
2.0
1.5
1.0
0.5
2
1
V
A
D
OUT
0
0
–0.5
–1.0
–1.5
–2.0
V
V
OUT
–1
–2
B
OUT
V
C
OUT
–3
–4
0
10 20 30 40 50 60 70 80 90 100 110 120 130
0
2
4
6
8
10
12
14
V
(V)
TEMPERATURE (ꢂC)
REF
TPC 4. Zero Code Error vs. Temperature
TPC 2. Relative Accuracy vs. VREF
REV. D
–7–
AD7226
SPECIFICATION RANGES
In order for the DACs to operate to their specifications, the
reference voltage must be at least 4 V below the VDD power
supply voltage. This voltage differential is required for correct
generation of bias voltages for the DAC switches.
DATA
O/P
+1/2 LSB
–1/2 LSB
The AD7226 is specified to operate over a VDD range from
+12 V ± 5% to +15 V ± 10% (i.e., from +11.4 V to +16.5 V)
with a VSS of –5 V ± 10%. Operation is also specified for a single
+15 V ± 5% VDD supply. Applying a VSS of –5 V results in
improved zero code error, improved output sink capability with
outputs near AGND and improved negative-going settling time.
Performance is specified over a wide range of reference voltages
from 2 V to (VDD – 4 V) with dual supplies. This allows a range
of standard reference generators to be used such as the AD780,
a 2.5 V band gap reference and the AD584, a precision 10 V
reference. Note that in order to achieve an output voltage range
of 0 V to 10 V a nominal 15 V ± 5% power supply voltage is
required by the AD7226.
Figure 7a. Positive Step Settling Time (VSS = –5 V)
DATA
SETTLING TIME
+1/2 LSB
–1/2 LSB
The output stage of the buffer amplifiers consists of a bipolar
NPN transistor from the VDD line and a constant current load to
VSS. VSS is the negative power supply for the output buffer ampli-
fiers. As mentioned in the op amp section, in single supply
operation the NMOS transistor will come out of saturation as the
output voltage approaches AGND and will act as a resistive load
of approximately 2 kW to AGND. As a result, the settling time for
negative-going signals approaching AGND in single supply opera-
tion will be longer than for dual supply operation where the
current load of 400 mA is maintained all the way down to AGND.
Positive-going settling-time is not affected by VSS.
O/P
Figure 7b. Negative Step Settling Time (VSS = –5 V)
GROUND MANAGEMENT
The settling-time for the AD7226 is limited by the slew-rate of
the output buffer amplifiers. This can be seen from Figure 6
which shows the dynamic response for the AD7226 for a full
scale change. Figures 7a and 7b show expanded settling-time
photographs with the output waveforms derived from a differen-
tial input to an oscilloscope. Figure 7a shows the settling time
for a positive-going step and Figure 7b shows the settling time
for a negative-going output step.
AC or transient voltages between AGND and DGND can cause
noise at the analog output. This is especially true in micropro-
cessor systems where digital noise is prevalent. The simplest
method of ensuring that voltages at AGND and DGND are
equal is to tie AGND and DGND together at the AD7226. In
more complex systems where the AGND and DGND intertie is
on the backplane, it is recommended that two diodes be con-
nected in inverse parallel between the AD7226 AGND and
DGND pins (IN914 or equivalent).
Unipolar Output Operation
This is the basic mode of operation for each channel of the
AD7226, with the output voltage having the same positive
polarity as +VREF. The AD7226 can be operated single supply
(VSS = AGND) or with positive/negative supplies (see op amp
section which outlines the advantages of having negative VSS).
The code table for unipolar output operation is shown in Table
II. Note that the voltage at VREF must never be negative with
respect to DGND in order to prevent parasitic transistor turn-on.
Connections for the unipolar output operation are shown in
Figure 8.
DATA
V
OUT
Figure 6. Dynamic Response (VSS = –5 V)
–8–
REV. D
AD7226
V
V
DD
With R1 = R2
REF
VOUT = 2D –1 ¥V
(4)
(
)
A
REF
MSB
LSB
V
A
B
where DA is a fractional representation of the digital word in latch A.
OUT
DB7
DAC A
DAC B
Mismatch between R1 and R2 causes gain and offset errors and
therefore these resistors must match and track over tempera-
ture. Once again the AD7226 can be operated in single supply
or from positive/negative supplies. Table III shows the digital
code versus output voltage relationship for the circuit of Figure 9
with R1 = R2.
V
DB0
OUT
V
C
OUT
WR
A1
DAC C
DAC D
V
REF
R1
R2
V
V
V
D
DD
REF
OUT
A0
AD7226*
+15V
V
A
OUT
V
OUT
AGND
DGND
DAC A
V
SS
–15V
R1, R2 = 10kꢃ ꢀ0.1%
*
Figure 8. AD7226 Unipolar Output Circuit
DIGITAL INPUTS OMITTED
FOR CLARITY
V
DGND
SS
AGND
Table II. Unipolar Code Table
Figure 9. AD7226 Bipolar Output Circuit
DAC Latch Contents
MSB
LSB
Analog Output
Table III. Bipolar (Offset Binary) Code Table
DAC Latch Contents
Ê 255ˆ
+V
+V
+V
+V
+V
0 V
REF Á
˜
1 1 1 1
1 1 1 1
MSB
LSB
Analog Output
Ë
¯
256
Ê127ˆ
+V
Ê129ˆ
REF Á
REF Á
˜
1 1 1 1
1 0 0 0
1 0 0 0
0 1 1 1
0 0 0 0
0 0 0 0
1 1 1 1
0 0 0 1
0 0 0 0
1 1 1 1
0 0 0 1
0 0 0 0
Ë
¯
128
˜
1 0 0 0
1 0 0 0
0 1 1 1
0 0 0 1
0 0 0 0
1 1 1 1
Ë
¯
256
Ê 1 ˆ
REF Á
+V
˜
Ë
¯
128
Ê128ˆ
VREF
2
= +
˜
REF Á
Ë
¯
256
0 V
Ê127ˆ
REF Á
˜
Ê 1 ˆ
REF Á
Ë
¯
256
–V
–V
–V
˜
Ë
¯
128
Ê 1 ˆ
REF Á
Ê127ˆ
˜
0 0 0 0
0 0 0 0
0 0 0 1
0 0 0 0
REF Á
˜
Ë
¯
256
Ë
¯
128
Ê128ˆ
= –V
˜
REF Á
REF
Ë
¯
128
Ê
Á
ˆ
¯
1
256
Note: LSB = V
2–8 =VREF
(
)
AGND BIAS
REF
(
)
˜
(2)
Ë
The AD7226 AGND pin can be biased above system GND
(AD7226 DGND) to provide an offset “zero” analog output
voltage level. Figure 10 shows a circuit configuration to achieve
this for channel A of the AD7226. The output voltage, VOUTA,
can be expressed as:
Bipolar Output Operation
Each of the DACs of the AD7226 can be individually config-
ured to provide bipolar output operation. This is possible using
one external amplifier and two resistors per channel. Figure 9
shows a circuit used to implement offset binary coding (bipolar
operation) with DAC A of the AD7226. In this case
VOUT A =VBIAS + D V
(5)
A
IN
where DA is a fractional representation of the digital input word
(0 £ D £ 255/256).
Ê
Ë
ˆ
Ê
ˆ
R2
R1
R2
R1
VOUT = 1+
¥ D V
–
¥ V
(
)
(
)
A
REF
REF
Á
˜
¯
Á
Ë
˜
¯
(3)
REV. D
–9–
AD7226
generated in software with each D/A converter being loaded
from a separate loop. The loops run through the look-up table
producing successive triads of sinusoidal values with 120∞
separation which are loaded to the D/A converters producing
three sine wave voltages 120∞ apart. A complete sine wave
cycle is generated by stepping through the full look-up table.
If a 256-element sine wave table is used then the resolution of
the circuit will be 1.4∞ (360∞/256). Figure 13 shows typical
resulting waveforms. The sine waves can be smoothed by filter-
ing the D/A converter outputs.
V
V
DD
REF
AD7226*
V
A
OUT
DAC A
AGND
5
V
BIAS
V
DGND
SS
The fourth D/A converter of the AD7226, DAC D, may be
used in a feedback configuration to provide a programmable
reference voltage for itself and the other three converters. This
configuration is shown in Figure 11. The relationship of VREF to
*
DIGITAL INPUTS OMITTED FOR CLARITY
Figure 10. AGND Bias Circuit
V
IN is dependent upon digital code and upon the ratio of RF to
For a given VIN, increasing AGND above system GND will
reduce the effective VDD–VREF which must be at least 4 V to
ensure specified operation. Note that because the AGND pin is
common to all four DACs, this method biases up the output
voltages of all the DACs in the AD7226. Note that VDD and VSS
of the AD7226 should be referenced to DGND.
R and is given by the formula.
1+G
(
)
VREF
=
¥VIN
(6)
1+G ¥ D
(
)
D
where G = RF/R
and DD is a fractional representation of the digital word in latch D.
3-PHASE SINE WAVE
Alternatively, for a given VIN and resistance ratio, the required
value of DD for a given value of VREF can be determined from
the expression
The circuit of Figure 11 shows an application of the AD7226 in
the generation of 3-phase sine waves which can be used to con-
trol small 3-phase motors. The proper codes for synthesizing a
full sine wave are stored in EPROM, with the required phase-
shift of 120∞ between the three D/A converter outputs being
generated in software.
VIN
VREF RF
R
DD = 1+ R / R
¥
–
(
)
F
(7)
Figure 12 shows typical plots of VREF versus digital code for
three different values of RF. With VIN = 2.5 V and RF = 3 R the
peak-to-peak sine wave voltage from the converter outputs will
vary between 2.5 V and 10 V over the digital input code range
of 0 to 255.
Data is loaded into the three D/A converters from the sine
EPROM via the microprocessor or control logic. Three loops are
ADDRESS
BUS
V
IN
V
REF
V
A
B
OUT
A0
A1
V
V
MICROPROCESSOR
OR
CONTROL LOGIC
OUT
R
ADDRESS
DECODE
F
SINE
EPROM
WR
C
D
OUT
R
V
OUT
AD7226
DATA
BUS
Figure 11. 3-Phase Sine Wave Generation Circuit
4.0V
3.5V
3.0V
2.5V
2.0V
1.5V
V
IN
IN
IN
IN
IN
IN
IN
V
= +15V
= –5V
DD
V
SS
V A
OUT
R
= 3R
F
V
B
OUT
R
R
= 2R
= R
F
V
C
OUT
F
0
16 32 48 64 80 96 112 128 144 160 176 192 208 224 240 256
DIGITAL CODE (Decimal Equivalent)
Figure 13. 3-Phase Sine Wave Output
Figure 12. Variation of VREF with Feedback Configuration
–10–
REV. D
AD7226
V
STAIRCASE WINDOW COMPARATOR
TEST
FROM D.U.T.
In many test systems, it is important to be able to determine
whether some parameter lies within defined limits. The staircase
window comparator of Figure 14a is a circuit that can be used,
for example, to measure the VOH and VOL thresholds of a TTL
device under test. Upper and lower limits on both VOH and VOL
can be programmably set using the AD7226. Each adjacent pair
of comparators forms a window of programmable size. If VTEST
lies within a window, then the output for that window will be
high. With a reference of 2.56 V applied to the VREF input, the
minimum window size is 10 mV.
10kꢃ
5V
WINDOW 1
V
V
REF
DD
V
A
B
OUT
V
OUT
10kꢃ
10kꢃ
5V
5V
WINDOW 2
WINDOW 3
AD7226
V
C
OUT
V
D
OUT
V
TEST
AGND
FROM D.U.T.
1/4 CA339
10kꢃ
5V
5V
5V
5V
5V
WINDOW 1
V
V
REF
DD
Figure 15a. Overlapping Windows
V
(HIGH)
(LOW)
OH
V
V
A
B
REF
OUT
10kꢃ
10kꢃ
10kꢃ
10kꢃ
WINDOW 1
WINDOW 2
WINDOW 3
WINDOW 4
WINDOW 5
V
V
B
A
OUT
OUT
V
OH
WINDOW 2
V
V
D
C
OUT
OUT
V
OUT
WINDOW 3
AD7226
AGND
V
(HIGH)
(LOW)
OL
V
C
OUT
Figure 15b. Window Structure
+15V
+4V
15kꢃ
10kꢃ
V
OL
V
D
OUT
–4V
AGND
V
V
DD
REF
*
AD7226*
DIGITAL INPUTS OMITTED
FOR CLARITY
V
A
OUT
Figure 14a. Logic Level Measurement
DAC A
V
REF
WINDOW 1
V
A
B
V
DGND
AGND
OUT
SS
WINDOW 2
WINDOW 3
V
OUT
Figure 16. Varying Reference Signal
VARYING REFERENCE SIGNAL
V
C
D
OUT
WINDOW 4
WINDOW 5
In some applications, it may be desirable to have a varying signal
applied to the reference input of the AD7226. The AD7226 has
multiplying capability within upper and lower limits of reference
voltage when operated with dual supplies. The upper and lower
limits are those required by the AD7226 to achieve its linearity
specification. Figure 16 shows a sine wave signal applied to the
reference input of the AD7226. For input signal frequencies up
to 50 kHz, the output distortion typically remains less than 0.1%.
Typical 3 dB bandwidth figure is 700 kHz.
V
OUT
AGND
Figure 14b. Window Structure
The circuit can easily be adapted to allow for overlapping of
windows as shown in Figure 15a. If the three outputs from this
circuit are decoded then five different nonoverlapping program-
mable windows can again be defined.
REV. D
–11–
AD7226
+10V
V
OFFSET ADJUST
Figure 17 shows how the AD7226 can be used to provide pro-
grammable input offset voltage adjustment for the AD544 op
amp. Each output of the AD7226 can be used to trim the input
offset voltage on one AD544. The 620 kW resistor tied to 10 V
provides a fixed bias current to one offset node. For symmetri-
cal adjustment, this bias current should equal the current in the
other offset node with the half-full scale code (i.e., 10000000)
on the DAC. Changing the code on the DAC varies the bias
current and hence provides offset adjust for the AD544. For
example, the input offset voltage on the AD544J, which has a
maximum of ±2 mV, can be programmably trimmed to ±10 mV.
+15V
7
V
DD
REF
AD7226*
V
A
OUT
620kꢃ
5
DAC A
4
1
500kꢃ
V
DGND
AGND
SS
–15V
*
DIGITAL INPUTS OMITTED
FOR CLARITY
Figure 17. Offset Adjust for AD544
6502 A15
A0
8085A A15
ADDRESS BUS
ADDRESS BUS
A8
A0
A1
AD7226*
WR
R/W
ꢄ2
EN ADDRESS
ADDRESS
EN
WR
DECODE
DECODE
EN
WR
A0
A1
AD7226*
DB7
DB0
DB7
DB0
DS2 8212
ALE
D7
D0
D7
D0
DATA BUS
LINEAR CIRCUITRY OMITTED FOR CLARITY
ADDRESS/DATA BUS
LINEAR CIRCUITRY OMITTED FOR CLARITY
*
*
Figure 20. AD7226 to 6502 Interface
Figure 18. AD7226 to 8085A Interface
Z-80 A15
6809 A15
ADDRESS BUS
ADDRESS BUS
A0
A0
A0
A1
A0
A1
ADDRESS
R/W
EN ADDRESS
EN
WR
EN
DECODE
DECODE
WR
WR
AD7226*
AD7226*
E
DB7
DB0
DB7
DB0
D7
D0
D7
D0
DATA BUS
LINEAR CIRCUITRY OMITTED FOR CLARITY
DATA BUS
LINEAR CIRCUITRY OMITTED FOR CLARITY
*
*
Figure 21. AD7226 to Z-80 Interface
Figure 19. AD7226 to 6809 Interface
–12–
REV. D
AD7226
OUTLINE DIMENSIONS
1.060 (26.92)
1.030 (26.16)
0.980 (24.89)
20
1
11
10
0.280 (7.11)
0.250 (6.35)
0.240 (6.10)
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
0.100 (2.54)
BSC
0.060 (1.52)
MAX
0.195 (4.95)
0.130 (3.30)
0.115 (2.92)
0.210 (5.33)
MAX
0.015
(0.38)
MIN
0.150 (3.81)
0.130 (3.30)
0.115 (2.92)
0.015 (0.38)
GAUGE
0.014 (0.36)
0.010 (0.25)
0.008 (0.20)
PLANE
SEATING
PLANE
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
0.430 (10.92)
MAX
0.005 (0.13)
MIN
0.070 (1.78)
0.060 (1.52)
0.045 (1.14)
COMPLIANT TO JEDEC STANDARDS MS-001
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS.
Figure 1. 20-Lead Plastic Dual In-Line Package [PDIP]
Narrow Body
(N-20)
Dimensions shown in inches and (millimeters)
0.098 (2.49)
0.005
MAX
0.310 (7.87)
0.220 (5.59)
(0.13)
MIN
20
11
10
1
PIN 1
0.060 (1.52)
0.015 (0.38)
0.320 (8.13)
0.290 (7.37)
0.200 (5.08)
1.060 (26.92) MAX
MAX
0.150 (3.81)
MIN
0.015 (0.38)
0.008 (0.20)
0.200 (5.08)
0.125 (3.18)
15°
0°
SEATING
PLANE
0.100
(2.54)
BSC
0.070 (1.78)
0.030 (0.76)
0.023 (0.58)
0.014 (0.36)
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 2. 20-Lead Ceramic Dual In-Line Package [CERDIP]
(Q-20)
Dimensions shown in inches and (millimeters)
Rev. D | Page 1
AD7226
7.50
7.20
6.90
11
20
5.60
5.30
5.00
8.20
7.80
7.40
1
10
0.25
0.09
1.85
1.75
1.65
2.00 MAX
8°
4°
0°
0.95
0.75
0.55
0.38
0.22
0.05 MIN
SEATING
PLANE
COPLANARITY
0.10
0.65 BSC
COMPLIANT TO JEDEC STANDARDS MO-150-AE
Figure 3. 20-Lead Shrink Small Outline Package [SSOP]
(RS-20)
Dimensions shown in millimeters
13.00 (0.5118)
12.60 (0.4961)
20
1
11
7.60 (0.2992)
7.40 (0.2913)
10.65 (0.4193)
10
10.00 (0.3937)
0.75 (0.0295)
0.25 (0.0
098)
45°
2.65 (0.1043)
2.35 (0.0925)
8°
0.30 (0.0118)
0.10 (0.0039)
0°
COPLANARITY
0.10
SEATING
PLANE
0.51 (0.0201)
0.31 (0.0122)
1.27 (0.0500)
0.40 (0.0157)
1.27
(0.0500)
BSC
0.33 (0.0130)
0.20 (0.0079)
COMPLIANT TO JEDEC STANDARDS MS-013-AC
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 4. 20-Lead Standard Small Outline Package [SOIC_W]
Wide Body
(RW-20)
Dimensions shown in millimeters and (inches)
Rev. D | Page
14
AD7226
0.180 (4.57)
0.165 (4.19)
0.048 (1.22 )
0.042 (1.07)
0.056 (1.42)
0.042 (1.07)
0.20 (0.51)
MIN
0.020 (0.50)
R
3
4
19
0.021 (0.53)
0.013 (0.33)
0.048 (1.22)
0.042 (1.07)
18
14
PIN 1
0.050
(1.27)
BSC
IDENTIFIER
BOTTOM
VIEW
(PINS UP)
0.330 (8.38)
0.290 (7.37)
TOP VIEW
(PINS DOWN)
0.032 (0.81)
0.026 (0.66)
8
9
13
0.020
(0.51)
R
0.045 (1.14)
0.025 (0.64)
R
0.356 (9.04)
0.350 (8.89)
SQ
0.120 (3.04)
0.090 (2.29)
0.395 (10.03)
0.385 (9.78)
SQ
COMPLIANT TO JEDEC STANDARDS MO-047-AA
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 5. 20-Lead Plastic Leaded Chip Carrier [PLCC]
(P-20A)
Dimensions shown in inches and (millimeters)
ORDERING GUIDE
Model1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Total Unadjusted Error2
Package Description
20 ꢀead CERDIP
20 ꢀead LLOP
20 ꢀead PDIP
20 ꢀead PDIP
20 ꢀead PꢀCC
20 ꢀead PꢀCC
20 ꢀead PꢀCC
20 ꢀead PꢀCC
20 ꢀead LOIC - Wide
20 ꢀead LOIC - Wide
20 ꢀead LOIC - Wide
20 ꢀead LOIC - Wide
Chips or Die
Package Option3
Q-20
RL-20
N-20
N-20
P-20A
P-20A
P-20A
AD7226BQ
AD7226BRLZ
AD7226KN
AD7226KNZ
AD7226KP
AD7226KP-REEꢀ
AD7226KPZ
AD7226KPZ-REEꢀ
AD7226KR
AD7226KR-REEꢀ
AD7226KRZ
AD7226KRZ-REEꢀ
AD7226BCHIPL
1 ꢀLB
1 ꢀLB
1 ꢀLB
1 ꢀLB
1 ꢀLB
1 ꢀLB
1 ꢀLB
1 ꢀLB
1 ꢀLB
1 ꢀLB
1 ꢀLB
1 ꢀLB
1 ꢀLB
P-20A
RW-20
RW-20
RW-20
RW-20
1 Z = ROHL Compliant Part.
2 Dual supply operation.
3 N = plastic DIP; P = plastic leaded chip carrier; Q = CERDIP; RW = LPIC; RL = LLOP.
Edits to Ordering Guide...................................................................3
Edits to Absolute Maximum Ratings..............................................3
Edits to Pin Configurations .............................................................4
Edits to Specifications Ranges.........................................................8
Outline Dimensions Updated........................................................13
RS-20 Package Added.....................................................................13
Updated RS-20 Package Outline Dimensions.............................13
REVISION HISTORY
1/11—Rev. C to Rev. D
Changes to Ordering Guide...........................................................15
3/03—Rev. B to Rev. C
Title Revision .....................................................................................1
3/03—Rev. A to Rev. B
Edits to Features ................................................................................1
Edits to Specifications.......................................................................2
Rev. D | Page
AD7226
NOTES
©2003-2011 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D00987-0-1/11(D)
Rev. D | Page
相关型号：
AD7226TE/883B
QUAD, PARALLEL, 8 BITS INPUT LOADING, 3 us SETTLING TIME, 8-BIT DAC, CQCC20, CERAMIC, LCC-20
ROCHESTER
©2020 ICPDF网 联系我们和版权申明