AD7266ASU [ADI]
Differential Input, Dual 2 MSPS, 12-Bit, 3-Channel SAR ADC; 差分输入,双通道2 MSPS , 12位, 3通道SAR ADC型号: | AD7266ASU |
厂家: | ADI |
描述: | Differential Input, Dual 2 MSPS, 12-Bit, 3-Channel SAR ADC |
文件: | 总17页 (文件大小:700K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Differential Input, Dual 2 MSPS,
12-Bit, 3-Channel SAR ADC
Preliminary Technical Data
AD7266
FUNCTIONAL BLOCK DIAGRAM
FEATURES
Dual 12-bit, 3-channel ADC
REF SELECT
D
A
AV
DV
CAP
DD
DD
Fast throughput rate: 2 MSPS
Specified for VDD of 2.7 V to 5.25 V
Low power: 12 mW max at 1.5 MSPS with 3 V supplies
30 mW max at 2 MSPS with 5 V supplies
Wide input bandwidth
70 dB SNR at 100 kHz input frequency
On-chip reference: 2.5 V
–40°C to +125°C operation
BUF
T/H
REF
AD7266
V
V
A1
A2
12-BIT
V
V
A3
A4
SUCCESSIVE
APPROXIMATION
ADC
OUTPUT
DRIVERS
MUX
D
A
OUT
V
V
A5
A6
SCLK
CS
Flexible power/throughput rate management
Simultaneous conversion/read
No pipeline delays
High speed serial interface SPI®/QSPI™/MICROWIRE™/DSP
compatible
RANGE
SGL/DIFF
A0
CONTROL
LOGIC
A1
A2
V
V
B1
B2
V
DRIVE
V
V
Shutdown mode: 1 µA max
32-lead LFCSP and TQFP packages
B3
B4
MUX
12-BIT
SUCCESSIVE
APPROXIMATION
ADC
OUTPUT
DRIVERS
D
B
T/H
OUT
V
V
B5
B6
GENERAL DESCRIPTION
BUF
The AD72661 is a dual, 12-bit, high speed, low power, successive
approximation ADC that operates from a single 2.7 V to 5.25 V
power supply and features throughput rates up to 2 MSPS. The
device contains two ADCs, each preceded by a 3-channel multi-
plexer, and a low noise, wide bandwidth track-and-hold amplifier
that can handle input frequencies in excess of 10 MHz.
AGND AGND AGND
D
B
DGND
DGND
CAP
Figure 1
PRODUCT HIGHLIGHTS
1. The AD7266 features two complete ADC functions that allow
simultaneous sampling and conversion of two channels. Each
ADC has 2 analog inputs, 3 fully differential pairs, or 6 single-
ended channels as programmed. The conversion result of both
channels is available simultaneously on separate data lines, or
in succession on one data line if only one serial port is
available.
The conversion process and data acquisition are controlled using
standard control inputs, allowing easy interfacing to microproces-
CS
sors or DSPs. The input signal is sampled on the falling edge of
conversion is also initiated at this point. The conversion time is
;
determined by the SCLK frequency. There are no pipelined delays
associated with the part.
The AD7266 uses advanced design techniques to achieve very low
2. High Throughput with Low Power Consumption
The AD7266 offers a 1.5 MSPS throughput rate with 8 mW
maximum power consumption when operating at 3 V.
power dissipation at high throughput rates. With 5 V supplies and a
2 MSPS throughput rate, the part consumes 4 mA maximum. The
part also offers flexible power/throughput rate management when
operating in sleep mode.
3. Flexible Power/Throughput Rate Management
The conversion rate is determined by the serial clock, allowing
power consumption to be reduced as conversion time is re-
duced through an SCLK frequency increase. Power efficiency
can be maximized at lower throughput rates if the part enters
sleep between conversions.
The analog input range for the part can be selected to be a 0 V to
VREF range or a 2VREF range with either straight binary or twos
complement output coding. The AD7266 has an on-chip 2.5 V
reference that can be overdriven if an external reference is pre-
ferred. This external reference range is 100 mV to 2.5 V. The
AD7266 is available in 32-lead lead frame chip scale (LFCSP) and
thin quad flat (TQFP) packages.
4. No Pipeline Delay
The part features two standard successive approximation
CS
ADCs with accurate control of the sampling instant via a
input and once off conversion control.
1Protected by U.S. Patent No. 6,681,332.
Rev. PrG
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.326.8703
www.analog.com
© 2004 Analog Devices, Inc. All rights reserved.
AD7266
Preliminary Technical Data
TABLE OF CONTENTS
AD7266—Specifications.................................................................. 3
Timing Specifications .................................................................. 4
Absolute Maximum Ratings............................................................ 5
ESD Caution.................................................................................. 5
Pin Configuration and Functional Descriptions.......................... 6
Terminology ...................................................................................... 8
Theory of Operation ...................................................................... 10
Circuit Information.................................................................... 10
Converter Operation.................................................................. 10
Analog Input ............................................................................... 11
Output Coding............................................................................ 11
Transfer Functions ..................................................................... 12
Digital Inputs .............................................................................. 12
VDRIVE ............................................................................................ 12
Modes of Operation....................................................................... 13
Normal Mode.............................................................................. 13
Partial Power-Down Mode ....................................................... 13
Full Power-Down Mode ............................................................ 14
Outline Dimensions....................................................................... 15
Ordering Guide............................................................................... 17
REVISION HISTORY
Revision PrG: Preliminary Version
Rev. PrG | Page 2 of 17
Preliminary Technical Data
AD7266—SPECIFICATIONS1
AD7266
Table 1. TA = TMIN to TMAX, VDD = 2.7 V to 3.3 V, fSCLK = 25 MHz, fS = 1.5 MSPS, VDRIVE = 2.7 V to 3.3 V; VDD = 4.75 V to 5.25 V,
fSCLK = 32 MHz, fS = 2 MSPS, VDRIVE = 2.7 V to 5.25 V; Reference = 2.5 V 1%, unless otherwise noted
Parameter
Specification
Unit
Test Conditions/Comments
DYNAMIC PERFORMANCE
Signal-to-Noise + Distortion Ratio (SINAD)2
Total Harmonic Distortion (THD)2
Spurious Free Dynamic Range (SFDR)2
Intermodulation Distortion (IMD)2
Second Order Terms
70
–75
–76
dB min
dB max
dB max
fIN = 100 kHz sine wave
fIN = 100 kHz sine wave
fIN = 100 kHz sine wave
–88
–88
–88
dB typ
dB typ
dB typ
Third Order Terms
Channel to Channel Isolation
SAMPLE AND HOLD
Aperture Delay3
Aperture Jitter3
10
50
ns max
ps typ
Aperture Delay Matching3
Full Power Bandwidth
200
20
2.5
ps max
MHz typ
MHz typ
@ 3 dB
@0.1 dB
DC ACCURACY
Resolution
12
1
1.5
0.ꢀ5
Bits
Integral Nonlinearity2
LSB max
LSB max
LSB max
0.5 LSB typ; differential configuration
0.5 LSB typ; single-ended configuration
Guaranteed no missed codes to 12 bits
Straight binary output coding
Differential Nonlinearity2
0 V to VREF Input Range
Offset Error
Offset Error Match
Gain Error
3
0.5
2
LSB max
LSB typ
LSB max
LSB typ
Gain Error Match
0.6
0 V to 2 × VREF Input Range
Positive Gain Error
Zero Code Error
Zero Code Error Match
Negative Gain Error
ANALOG INPUT
Twos complement output coding
2
3
1
1
LSB max
LSB max
LSB typ
LSB max
Input Voltage Ranges
0 V to VREF
V
V
CS
RANGE pin low upon falling edge
0 V to 2 x VREF
CS
RANGE pin high upon falling edge
DC Leakage Current
Input Capactiance
500
1
30
nA max
µA max
pF typ
pF typ
TA = –40°C to +85°C
85°C < TA ≤ 125°C
When in track
10
When in hold
REFERENCE INPUT/OUTPUT
Reference Output Voltage4
Reference Input Voltage Range
DC Leakage Current
2.4ꢀ/2.51
0.1/2.5
30
V min/V max
V min/V max
µA max
See Typical Performance plots
VREF pin
160
20
25
25
10
µA max
pF typ
Ω typ
ppm/°C max
ppm/°C typ
DCAPA, DCAPB pins
Input Capactiance
VREF Output Impedance5
Reference Temperature Coefficient
LOGIC INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
2.8
0.4
1
V min
V max
µA max
pF max
Typically 15 nA, VIN = 0 V or VDRIVE
3
Input Capacitance, CIN
10
Rev. PrG | Page 3 of 17
AD7266
Preliminary Technical Data
Parameter
Specification
Unit
Test Conditions/Comments
LOGIC OUTPUTS
Output High Voltage, VOH
Output Low Voltage, VOL
Floating State Leakage Current
Floating State Output Capacitance3
Output Coding
VDRIVE – 0.2
0.4
1
V min
V max
µA max
pF max
10
Straight (Natural) Binary
Twos Complement
DIFF
DIFF
SGL/
= 1 with 0 V to VREF range selected
DIFF
SGL/
= 0; SGL/
= 1 with 0 V to 2 × VREF range
CONVERSION RATE
Conversion Time
Track/Hold Acquisition Time3
Throughput Rate
POWER REQUIREMENTS
VDD
14
100
2
SCLK Cycles
ns max
MSPS max
437.5 ns with SCLK = 32 MHz
2.7/5.25
2.7/5.25
V min/V max
V min/V max
VDRIVE
6
IDD
Digital I/Ps = 0 V or VDRIVE
Normal Mode (Static)
Operational, fs = 2 MSPS
2
6
4
TBD
500
1
mA max
mA max
mA max
mA max
µA max
µA max
VDD = 5 V
VDD = 3 V
fs = 200 kSPS
Static
Partial Power-Down Mode
Partial Power-Down Mode
Full Power-Down Mode
Power Dissipation6
Normal Mode (Operational)
Partial Power-Down (Static)
Full Power-Down (Static)
30
2.5
5
mW max
mW max
µW max
VDD = 5 V
VDD = 5 V
VDD = 5 V
NOTES
1 Temperature ranges as follows: -40°C to +125°C
2 See Terminology section.
3 Sample tested during initial release to ensure compliance.
4 Relates to Pins DCAPA or DCAPB.
5 See Reference section for DCAPA, DCAPB output impedances.
6 See Power Versus Throughput Rate section.
TIMING SPECIFICATIONS
Table 2. AVDD = DVDD = 2.7 V to 5.25 V, VDRIVE = 2.7 V to 5.25 V, TA = TMAX to TMIN, unless otherwise noted
Parameter
Limit at TMIN, TMAX
Unit
Description
fSCLK
10
34
14 × tSCLK
437.5
560
kHz min
MHz max
ns max
ns max
ns max
ns max
tCONVERT
tSCLK = 1/fSCLK
fSCLK = 32 MHz, VDD = 5 V, FSAMPLE = 2 MSPS
fSCLK = 25 MHz, VDD = 3 V, FSAMPLE = 1.5 MSPS
CS
Minimum time between end of serial read and next falling edge of
tQUIET
t2
35
10
25
ns min
ns max
CS
to SCLK setup time
t3
CS
Delay from until DOUTA and DOUTB are three-state disabled
Data access time after SCLK falling edge.
SCLK low pulse width
SCLK high pulse width
SCLK to data valid hold time
t4
t5
t6
t7
t8
tꢀ
25
ns max
ns min
ns min
ns min
ns max
ns min
0.4tSCLK
0.4tSCLK
5
25
CS
CS
rising edge to DOUTA, DOUTB, high impedance
rising edge to falling edge pulsewidth
60
t10
5
30
ns min
ns max
SCLK falling edge to DOUTA, DOUTB, high impedance
SCLK falling edge to DOUTA, DOUTB, high impedance
All timing specifications given are with a 25 pF load capacitance. With a load capacitance greater than this value, a digital buffer or latch must be used.
Rev. PrG | Page 4 of 17
Preliminary Technical Data
AD7266
ABSOLUTE MAXIMUM RATINGS
Table 3. AD7266 Stress Ratings
Stresses above those listed under Absolute Maximum Ratings
Parameter
Rating
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
VDD to AGND
DVDD to DGND
VDRIVE to DGND
VDRIVE to AGND
AVDD to DVDD
AGND to DGND
Analog Input Voltage to AGND
Digital Input Voltage to DGND
Digital Output Voltage to GND
VREF to AGND
Input Current to Any Pin Except
Supplies1
–0.3 V to +7 V
–0.3 V to +7 V
–0.3 V to DVDD
–0.3 V to AVDD
–0.3 V to +0.3 V
–0.3 V to +0.3 V
–0.3 V to AVDD +0.3 V
–0.3 V to +7 V
–0.3 V to VDRIVE +0.3 V
–0.3 V to AVDD +0.3 V
10 mA
Operating Temperature Range
Storage Temperature Range
Junction Temperature
LFCSP Package
–40°C to +125°C
–65°C to +150°C
150°C
θJA Thermal Impedance
θJC Thermal Impedance
Lead Temperature, Soldering
Reflow Temperature (10- 30 sec)
ESD
108.2°C/W
32.71°C/W
255°C
TBD
1 Transient currents of up to 100 mA will not cause SCR latch up.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. PrG | Page 5 of 17
AD7266
Preliminary Technical Data
PIN CONFIGURATION AND FUNCTIONAL DESCRIPTIONS
32 31 30 29 28 27 26 25
1
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
DGND
A1
REF SELECT
A2
AV
SGL/DIFF
RANGE
DD
A
D
AD7266
CAP
TOP VIEW
AGND
D
B
CAP
(Not to Scale)
AGND
AGND
V
V
V
V
A1
A2
B1
B2
9
10 11 12 13 14 15 16
Figure 2. AD7266 Pin Configuration
Table 4. AD7266 Pin Function Descriptions
Pin No. Mnemonic Description
4, 20
DCAPA,
DCAP
Decoupling capacitors (470nF recommended) are connected to these pins to decouple the reference buffer for
each respective ADC. The on-chip reference can be taken from these pins and applied externally to the rest of a
system. The range of the external reference is dependent on the analog input range selected. See the Reference
Configuration Options section.
B
7–12
18–13
27
VA1–VA6
VB1–VB6
SCLK
Analog Inputs of ADC A. These may be programmed as six single-ended channels or three true differential analog
input channel pairs. See Table 6.
Analog Inputs of ADC B. These may be programmed as six single-ended channels or three true differential analog
input channel pairs. See Table 6.
Serial Clock. Logic Input. A serial clock input provides the SCLK for accessing the data from the AD7266. This clock
is also used as the clock source for the conversion process.
5, 6, 1ꢀ
AGND
Analog Ground. Ground reference point for all analog circuitry on the AD7266. All analog input signals and any
external reference signal should be referred to this AGND voltage. All three of these AGND pins should connect to
the AGND plane of a system. The AGND and DGND voltages ideally should be at the same potential and must not
be more than 0.3 V apart, even on a transient basis.
32
DVDD
VDRIVE
DGND
AVDD
Digital Supply Voltage, 2.7 V to 5.25 V. This is the supply voltage for all digital circuitry on the AD7266. The DVDD
and AVDD voltages should ideally be at the same potential and must not be more than 0.3 V apart even on a
transient basis. This supply should be decoupled to DGND.
Logic power supply input. The voltage supplied at this pin determines at what voltage the interface will operate.
This pin should be decoupled to DGND. The voltage at this pin may be different to that at AVDD and DVDD but
should never exceed either by more than 0.3 V.
Digital Ground. This is the ground reference point for all digital circuitry on the AD7266. Both DGND pins should
connect to the DGND plane of a system. The DGND and AGND voltages should ideally be at the same potential
and must not be more than 0.3 V apart, even on a transient basis.
Analog Supply Voltage, 2.7 V to 5.25 V. This is the only supply voltage for all analog circuitry on the AD7266. The
AVDD and DVDD voltages should ideally be at the same potential and must not be more than 0.3 V apart, even on a
transient basis. This supply should be decoupled to AGND.
31
1, 2ꢀ
3
26
CS
Chip Select. Active low logic input. This input provides the dual function of initiating conversions on the AD7266
and frames the serial data transfer.
30, 28
DOUTA,
Serial Data Outputs. The data output is supplied to this pin as a serial data stream. The bits are clocked out on the
falling edge of the SCLK input and 14 SCLKs are required to access the data. The data appears on both pins
simultaneously from the simultaneous conversions of both ADCs. The data stream consists of two leading zeros
DOUT
B
CS
followed by the 12 bits of conversion data. The data is provided MSB first. If is held low for 16 SCLK cycles
CS
rather than 14, then two trailing zeros will appear after the 12 bits of data. If is held low for a further 16 SCLK
cycles after this on either DOUTA or DOUTB, the data from the other ADC follows on the DOUT pin. This allows data
from a simultaneous conversion on both ADCs to be gathered in serial format on either DOUTA or DOUTB alone
using only one serial port. See the Serial Interface section.
Rev. PrG | Page 6 of 17
Preliminary Technical Data
AD7266
Pin No. Mnemonic Description
21
RANGE
Analog Input Range Selection. Logic input. The polarity on this pin will determine what input range the analog
CS
input channels will have. On the falling edge of , the polarity of this pin is checked to determine the analog
input range of the next conversion. If this pin is tied to a logic low, the analog input range is 0 V to VREF. If this pin
CS
is tied to a logic high when
goes low, the analog input range is 2 × VREF.
25–23
A0–A2
Multiplexer Select. Logic inputs. Thess inputs are used to select the pair of channels to be converted
simultaneously, i.e., Channel 1 of both ADC A and ADC B, Channel 2 of both ADC A and ADC, and so on. The pair of
channels selected may be two single ended channels or two differential pairs. The logic states of these pins are
CS
checked upon the falling edge of , and the multiplexer is set up for the next conversion. See Table 6 for
multiplexer address decoding.
22
2
DIFF
SGL/
Logic Input. This pin selects whether the analog inputs are configured as differential pairs or single ended. A logic
low selects differential operation while a logic high selects single ended operation.
REF SELECT Internal/External reference Selection. Logic Input. If this pin is tied to GND, the on-chip 2.5 V reference is used as
the reference source for both ADC A and ADC B. In addition, Pins DCAPA and DCAPB must be tied to decoupling
capacitors. If the REF SELECT pin is tied to a logic high, an external reference can be supplied to the AD7266
through the DCAPA and/or DCAPB pins.
Rev. PrG | Page 7 of 17
AD7266
Preliminary Technical Data
TERMINOLOGY
Differential Nonlinearity
Track-and-Hold Acquisition Time
This is the difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
The track-and-hold amplifier returns into track mode after the
end of conversion. Track-and-hold acquisition time is the time
required for the output of the track-and-hold amplifier to reach
its final value, within 1/2 LSB, after the end of conversion.
Integral Nonlinearity
This is the maximum deviation from a straight line passing
through the endpoints of the ADC transfer function. The
endpoints of the transfer function are zero scale, a point 1 LSB
below the first code transition, and full scale, a point 1 LSB
above the last code transition.
Signal to (Noise + Distortion) Ratio
This is the measured ratio of signal to (noise + distortion) at the
output of the A/D converter. The signal is the rms amplitude of
the fundamental. Noise is the sum of all non-fundamental
signals up to half the sampling frequency (fS/2), excluding dc.
The ratio is dependent on the number of quantization levels in
the digitization process; the more levels, the smaller the
quantization noise. The theoretical signal to (noise + distortion)
ratio for an ideal N-bit converter with a sine wave input is given
by:
Offset Error
This applies to Straight Binary output coding. It is the deviation
of the first code transition (00 . . . 000) to (00 . . . 001) from the
ideal, i.e., AGND + 1 LSB.
Offset Error Match
Signal to (Noise + Distortion) = (6.02N + 1.76) dB
This is the difference in Offset Error between the two channels.
Thus for a 12-bit converter, this is 74 dB.
Gain Error
Total Harmonic Distortion
This applies to Straight Binary output coding. It is the deviation
of the last code transition (111 . . . 110) to (111 . . . 111) from the
ideal (i.e., VREF – 1 LSB) after the offset error has been adjusted
out.
Total harmonic distortion (THD) is the ratio of the rms sum of
harmonics to the fundamental. For the AD7266 it is defined as:
2
V22 +V32 +V42 +V52 +V6
THD(dB) = 20log
V1
Gain Error Match
where V1 is the rms amplitude of the fundamental and V2, V3,
V4, V5 and V6 are the rms amplitudes of the second through the
sixth harmonics.
This is the difference in Gain Error between the two channels.
Zero Code Error
This applies when using twos complement output coding in
particular with the 2 x VREF input range as –VREF to +VREF biased
about the VREF point. It is the deviation of the midscale
transition (all 1s to all 0s) from the ideal VIN voltage, i.e., VREF - 1
LSB.
Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to fS/2 and excluding dc) to the rms value of the
fundamental. Normally, the value of this specification is
determined by the largest harmonic in the spectrum, but for
ADCs where the harmonics are buried in the noise floor, it will
be a noise peak.
Zero Code Error Match
This refers to the difference in Zero Code Error between the
two channels.
Channel-to-Channel Isolation
Positive Gain Error
Channel-to-channel isolation is a measure of the level of
crosstalk between channels. It is measured by applying a full-
scale (2 x VREF), 455kHz sine wave signal to all unselected input
channels and determining how much that signal is attenuated in
the selected channel with a 10 kHz signal (0 V to VREF). The
figure given is the worst-case across all twelve channels for the
AD7266.
This applies when using twos complement output coding in
particular with the 2 x VREF input range as –VREF to +VREF biased
about the VREF point. It is the deviation of the last code
transition (011…110) to (011…111) from the ideal (i.e., + VREF
-
1 LSB) after the Zero Code Error has been adjusted out.
Rev. PrG | Page 8 of 17
Preliminary Technical Data
AD7266
Intermodulation Distortion
As a result, the second and third order terms are specified
separately. The calculation of the intermodulation distortion is
as per the THD specification where it is the ratio of the rms
sum of the individual distortion products to the rms amplitude
of the sum of the fundamentals expressed in dBs.
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities will create distortion
products at sum and difference frequencies of mfa nfb where
m, n = 0, 1, 2, 3, etc. Intermodulation distortion terms are those
for which neither m nor n are equal to zero. For example, the
second order terms include (fa + fb) and (fa – fb), while the
third order terms include (2fa + fb), (2fa – fb), (fa + 2fb) and (fa
– 2fb).
PSR (Power Supply Rejection)
Variations in power supply will affect the full-scale transition
but not the converter’s linearity. Power supply rejection is the
maximum change in full-scale transition point due to a change
in power supply voltage from the nominal value. See Typical
Performance Curves.
The AD7266 is tested using the CCIF standard where two input
frequencies near the top end of the input bandwidth are used.
In this case, the second order terms are usually distanced in
frequency from the original sine waves while the third order
terms are usually at a frequency close to the input frequencies.
Rev. PrG | Page ꢀ of 17
AD7266
Preliminary Technical Data
THEORY OF OPERATION
CIRCUIT INFORMATION
CAPACITIVE
DAC
The AD7266 is a fast, micropower, dual 12-bit, single supply,
A/D converter that operates from a 2.7 V to 5.25 V supply.
When operated from a 5 V supply, the AD7266 is capable of
throughput rates of 2 MSPS when provided with a TBD MHz
clock, and a throughput rate of 1.5 MSPS at 3 V.
COMPARATOR
C
C
B
A
S
V
V
IN+
SW1
SW2
CONTROL
LOGIC
SW3
S
A
B
IN–
V
REF
The AD7266 contains two on-chip differential track-and-hold
amplifiers, two successive approximation A/D converters, and a
serial interface with two separate data output pins, and is
housed in a 32-lead LFCSP package, which offers the user
considerable space-saving advantages over alternative solutions.
The serial clock input accesses data from the part but also
provides the clock source for each successive approximation
ADC. The analog input range for the part can be selected to be a
0 V to VREF input or a 2 × VREF input with the analog inputs
configured as either single ended or differential. The AD7266
has an on-chip 2.5 V reference that can be overdriven if an
external reference is preferred.
CAPACITIVE
DAC
Figure 3. ADC Acquisition Phase
When the ADC starts a conversion (Figure 4), SW3 opens and
SW1 and SW2 move to position B, causing the comparator to
become unbalanced. Both inputs are disconnected once the
conversion begins. The control logic and the charge redistribu-
tion DACs are used to add and subtract fixed amounts of charge
from the sampling capacitor arrays to bring the comparator
back into a balanced condition. When the comparator is
rebalanced, the conversion is complete. The control logic
generates the ADC output code. The output impedances of the
sources driving the VIN+ and VIN– pins must be matched;
otherwise, the two inputs will have different settling times,
resulting in errors.
The AD7266 also features power-down options to allow power
saving between conversions. The power-down feature is
implemented across the standard serial interface, as described in
the Modes of Operation section.
CONVERTER OPERATION
The AD7266 has two successive approximation analog-to-
digital converters, each based around two capacitive DACs.
Figure 3 and Figure 4 show simplified schematics of one of
these ADCs in acquisition and conversion phase, respectively.
The ADC is comprised of control logic, a SAR, and two
capacitive DACs. In Figure 3 (the acquisition phase), SW3, is
closed, SW1 and SW2 are in position A, the comparator is held
in a balanced condition, and the sampling capacitor arrays
acquire the differential signal on the input.
CAPACITIVE
DAC
COMPARATOR
C
C
B
A
S
V
V
IN+
SW1
SW2
CONTROL
LOGIC
SW3
S
A
B
IN–
V
REF
CAPACITIVE
DAC
Figure 4. ADC Conversion Phase
Rev. PrG | Page 10 of 17
Preliminary Technical Data
AD7266
ANALOG INPUT
The channels to be converted on simultaneously are selected via
the multiplexer address inputs A0 to A2. The logic states of
The analog inputs of the AD7266 may be configured as single
ended or true differential via the SGL/
DIFF
logic pin, as shown
CS
these pins are also checked upon the falling edge of
and the
CS
in Figure 5. On the falling edge of , point A, the logic level of
DIFF
channels are chosen for the next conversion. The selected input
channels are decoded as shown in Table 6.
the SGL/
pin is checked to determine the configuration of
the analog input channels for the next conversion. If this pin is
tied to a logic low, the analog input channels to each on-chip
ADC are set up as three true differential pairs. If this pin is at a
The analog input range of the AD7266 can be selected as 0 V to
VREF or 0 V to 2 × VREF via the RANGE pin. This selection is
CS
logic high when
on-chip ADC are set up as six single-ended analog inputs. In
DIFF
goes low, the analog input channels to each
DIFF
made in a similar fashion to that of the SGL/
checking the logic state of the RANGE pin upon the falling edge
CS
pin by
Figure 5 at point A, the SGL/
pin is at a logic high so the
of . The analog input range is set up for the next conversion.
analog inputs are configured as single-ended for the next
conversion, i.e. sampling point B. At point B, the logic level of
CS
If this pin is tied to a logic low upon the falling edge of , the
analog input range for the next conversion is 0 V to VREF. If this
DIFF
the SGL/
pin has changed to low; there fore, the analog
CS
pin is tied to a logic high upon the falling edge of , the analog
inputs are configured as differential for the next conversion
after this one, even though this current conversion is on single
ended configured inputs.
input range for the next conversion is 0 V to 2 × VREF
.
OUTPUT CODING
The AD7266 output coding is set to either twos complement or
straight binary depending on which analog input configuration
is selected for a conversion. Table 5 shows which output coding
scheme is used for each possible analog input configuration.
A
B
CS
1
14
1
14
SCLK
Table 5 AD7266 Output Coding
DIFF
Range
Output Coding
SGL/DIFF
SGL/
DIFF
DIFF
SGL
0 V to VREF
0 V to 2 × VREF
0 V to VREF
Twos Complement
Twos Complement
Straight Binary
Figure 5. Selecting Differential or Single Ended Configuration
SGL
PSUEDO DIFF
PSUEDO DIFF
0 V to 2 × VREF
0 V to VREF
0 V to 2 × VREF
Twos Complement
Straight Binary
Twos Complement
Table 6. Analog Input Type and Channel Selection
ADC A
VIN–
ADC B
VIN–
DIFF
VIN+
VIN+
Comment
A2
0
0
0
0
1
1
0
0
0
0
1
1
A1
0
0
1
1
0
0
0
0
1
1
0
0
A0
0
1
0
1
0
1
0
1
0
1
0
1
SGL/
1
1
1
1
1
1
0
0
0
0
0
0
VA1
VA2
VA3
VA4
VA5
VA6
VA1
VA1
VA3
VA3
VA5
VA5
AGND
VB1
VB2
VB3
VB4
VB5
VB6
VB1
VB1
VB3
VB3
VB5
VB5
AGND
AGND
AGND
AGND
AGND
AGND
VB2
VB2
VB4
VB4
VB6
Single Ended
Single Ended
Single Ended
Single Ended
Single Ended
Single Ended
Fully Differential
Pseudodifferential
Fully Differential
Pseudodifferential
Fully Differential
Pseudodifferential
AGND
AGND
AGND
AGND
AGND
VA2
VA2
VA4
VA4
VA6
VA6
VB6
Rev. PrG | Page 11 of 17
AD7266
Preliminary Technical Data
DIGITAL INPUTS
TRANSFER FUNCTIONS
The digital inputs applied to the AD7266 are not limited by the
maximum ratings that limit the analog inputs. Instead, the
digital inputs applied can go to 7 V and are not restricted by the
VDD + 0.3 V limit as on the analog inputs. See the Absolute
Maximum Ratings. Another advantage of SCLK, RANGE,
The designed code transitions occur at successive integer LSB
values (i.e., 1 LSB, 2 LSB, and so on). The LSB size is VREF/4096.
The ideal transfer characteristic for the AD7266 when straight
binary coding is output is shown in Figure 6, and the ideal
transfer characteristic for the AD7266 when twos complement
coding is output is shown in Figure 7.
CS
A0–A2, and
not being restricted by the VDD + 0.3 V limit is
that power supply sequencing issues are avoided. If one of these
digital inputs is applied before VDD, there is no risk of latch-up,
as there would be on the analog inputs if a signal greater than
0.3 V were applied prior to VDD.
111...111
111...110
VDRIVE
The AD7266 also has the VDRIVE feature, which controls the
voltage at which the serial interface operates. VDRIVE allows the
ADC to easily interface to both 3 V and 5 V processors. For
example, if the AD7266 was operated with a VDD of 5 V, the
VDRIVE pin could be powered from a 3 V supply, allowing a large
dynamic range with low voltage digital processors. For example,
the AD7266 could be used with the 2 × VREF input range, with a
VDD of 5 V while still being able to interface to 3 V digital parts.
111...000
1LSB = V
REF
/4096
011...111
000...010
000...001
000...000
1LSB
V
– 1LSB
REF
ANALOG INPUT
0V
Figure 6. Straight Binary Transfer Characteristic
1LSB = 2
×
V
/4096
REF
011...111
011...110
000...001
000...000
111...111
100...010
100...001
100...000
–V
+ 1LSB
V
– 1LSB
+V
– 1 LSB
REF
REF
REF
ANALOG INPUT
Figure 7. Twos Complement Transfer Characteristic with VREF VREF Input
Range
Rev. PrG | Page 12 of 17
Preliminary Technical Data
AD7266
MODES OF OPERATION
The mode of operation of the AD7266 is selected by controlling
accessed on the same DOUT line, as shown in Figure TBD (see
the Serial Interface section). The identification bit provided
prior to each conversion result identifies which on-board ADC
the following result is from. Once 32 SCLK cycles have elapsed,
the DOUT line returns to three-state on the 32nd SCLK falling
CS
the (logic) state of the
three possible modes of operation: normal mode, partial power-
CS
signal during a conversion. There are
down mode, and full power-down mode. The point at which
is pulled high after the conversion has been initiated determines
which power-down mode, if any, the device enters. Similarly, if
CS
edge. If
to three-state at that point. Thus,
cycles until it is brought high again sometime prior to the next
CS
is brought high prior to this, the DOUT line returns
CS
may idle low after 32 SCLK
CS
already in a power-down mode,
can control whether the
device returns to normal operation or remains in power-down.
These modes of operation are designed to provide flexible
power management options. These options can be chosen to
optimize the power dissipation/throughput rate ratio for
differing application requirements.
conversion (effectively idling
low), if so desired, since the
bus still returns to three-state upon completion of the dual
result read.
Once a data transfer is complete and DOUTA and DOUTB have
returned to three-state, another conversion can be initiated after
NORMAL MODE
CS
the quiet time, tQUIET, has elapsed by bringing
low again.
This mode is intended for fastest throughput rate performance
since the user does not have to worry about any power-up times
with the AD7266 remaining fully powered all the time. Figure 8
shows the general diagram of the operation of the AD7266 in
this mode.
PARTIAL POWER-DOWN MODE
This mode is intended for use in applications where slower
throughput rates are required. Either the ADC is powered down
between each conversion, or a series of conversions may be
performed at a high throughput rate and the ADC is then
powered down for a relatively long duration between these
bursts of several conversions. When the AD7266 is in partial
power-down, all analog circuitry is powered down except for
the on-chip reference and reference buffer.
CS
1
10
14
SCLK
D
D
A
B
OUT
To enter partial power-down, the conversion process must be
LEADING ZERO, I.D. BIT + CONVERSION RESULT
OUT
CS
interrupted by bringing
falling edge of SCLK and before the 10th falling edge of SCLK, as
CS
high anywhere after the second
Figure 8. Normal Mode Operation
shown in Figure 9. Once
window of SCLKs, the part enters partial power-down, the
CS
has been brought high in this
CS
The conversion is initiated on the falling edge of , as
described in the Serial Interface section. To ensure that the part
remains fully powered up at all times,
at least 10 SCLK falling edges have elapsed after the falling edge
conversion that was initiated by the falling edge of
terminated, and DOUTA and DOUTB go back into three-state. If
CS
is
CS
must remain low until
is brought high before the second SCLK falling edge, the
part remains in normal mode and does not power down. This
th
CS CS
of . If
is brought high any time after the 10 SCLK falling
CS
avoids accidental power-down due to glitches on the
line.
edge but before the 14th SCLK falling edge, the part remains
powered up but the conversion is terminated and DOUTA and
DOUTB go back into three-state. Fourteen serial clock cycles are
required to complete the conversion and access the conversion
result. The DOUT line does not return to three-state after 14
CS
1
2
10
14
CS
SCLK cycles have elapsed, but instead does so when
is
is left low for another 2 SCLK cycles
(e.g. if only a 16 SCLK burst is available), two trailing zeros are
CS
SCLK
CS
brought high again. If
D
A
B
TRI-STATE
OUT
D
OUT
clocked out after the data. If
is left low for a further 16 SCLK
cycles again, the result from the other ADC on board is also
Figure 9. Entering Partial Power-Down Mode
Rev. PrG | Page 13 of 17
AD7266
Preliminary Technical Data
AD7266 is in full power-down, all analog circuitry is powered
down. Full power-down is entered in a similar way as partial
power-down, except the timing sequence shown in Figure 9
must be executed twice. The conversion process must be
To exit this mode of operation and power up the AD7266 again,
CS
a dummy conversion is performed. On the falling edge of
,
the device begins to power up, and continues to power up as
th
CS
long as
is held low until after the falling edge of the 10
CS
interrupted in a similar fashion by bringing
high anywhere
SCLK. The device is fully powered up after approximately 1 µs
has elapsed, and valid data results from the next conversion, as
after the second falling edge of SCLK and before the 10th falling
edge of SCLK. The device enters partial power-down at this
point. To reach full power-down, the next conversion cycle must
be interrupted in the same way, as shown in Figure TBD. Once
CS
shown in Figure 10. If
is brought high before the second
falling edge of SCLK, the AD7266 again goes into partial power-
down. This avoids accidental power-up due to glitches on the
CS
has been brought high in this window of SCLKs, the part
CS
line. Although the device may begin to power up on the
CS
powers down completely.
falling edge of , it powers down again on the rising edge of
CS
CS
. If the AD7266 is already in partial power-down mode and
is brought high between the second and 10 falling edges of
CS
Note that it is not necessary to complete the 14 SCLKs once
has been brought high to enter a power-down mode.
th
SCLK, the device enters full power-down mode.
To exit full power-down and power the AD7266 up again, a
FULL POWER-DOWN MODE
dummy conversion is performed, as when powering up from
CS
partial power-down. On the falling edge of , the device
This mode is intended for use in applications where throughput
rates slower than those in the partial power-down mode are
required, as power-up from a full power-down takes substan-
tially longer than that from partial power-down. This mode is
more suited to applications where a series of conversions
performed at a relatively high throughput rate are followed by a
long period of inactivity and thus power-down. When the
CS
begins to power up and continues to power up as long as
is
held low until after the falling edge of the 10th SCLK. The
power-up time required must elapse before a conversion can be
initiated, as shown in Figure TBD. See the Power-Up Times
section for the power-up times associated with the AD7266.
THE PART BEGINS
TO POWER-UP
THE PART IS FULLY POWERED UP,
SEE POWER-UP TIMES SECTION
T
POWER-UP
CS
1
10
14
1
14
SCLK
A
D
D
A
B
OUT
INVALID DATA
VALID DATA
OUT
Figure 10. Exiting Partial Power-Down Mode
Rev. PrG | Page 14 of 17
Preliminary Technical Data
SERIAL INTERFACE
AD7266
for DOUTA is shown. Note that in this case, the DOUT line in use
will go back into three-state on the 32nd SCLK falling edge or
Figure 11 shows the detailed timing diagram for serial
interfacing to the AD7266. The serial clock provides the
conversion clock and controls the transfer of information from
the AD7266 during conversion.
CS
the rising edge of , whichever occurs first.
A minimum of fourteen serial clock cycles are required to
perform the conversion process and to access data from one
CS
The
signal initiates the data transfer and conversion process.
CS
CS
conversion on either data line of the AD7266.
going low
The falling edge of
puts the track and hold into hold mode
provides the leading zero to be read in by the microcontroller or
DSP. The remaining data is then clocked out by subsequent
SCLK falling edges, beginning with a second leading zero. Thus
the first falling clock edge on the serial clock has the leading
zero provided and also clocks out the second leading zero. The
12 bit result then follows with the final bit in the data transfer
valid on the fourteenth falling edge, having being clocked out
on the previous (thirteenth) falling edge. In applications with a
slower SCLK, it may be possible to read in data on each SCLK
rising edge depending on the SCLK frequency used, i.e., the first
and takes the bus out of three-state; the analog input is sampled
at this point. The conversion is also initiated at this point and
requires a minimum of 14 SCLKs to complete. Once 13 SCLK
falling edges have elapsed, the track-and-hold will go back into
track on the next SCLK rising edge, as shown in Figure 11 at
point B. If a 16 SCK transfer is used then 2 trailing zeros will
CS
appear after the final LSB. On the rising edge of , the
conversion will be terminated and DOUTA and DOUTB will go
CS
back into three-state. If
is not brought high but is instead
held low for a further 14 (or 16) SCLK cycles on DOUTA, the data
from conversion B will be output on DOUTA (followed by 2
CS
rising edge of SCLK after the
falling edge would have the
leading zero provided and the thirteenth rising SCLK edge
would have DB0 provided.
CS
trailing zeros). Likewise, if
is held low for a further 14 (or 16)
SCLK cycles on DOUTB, the data from conversion A will be
output on DOUTB. This is illustrated in Figure 12 where the case
CS
t9
t2
t6
B
SCLK
3
4
5
1
2
13
14
t8
t5
tquiet
t7
t4
t3
D
D
A
0
DB11
DB10
DB2
OUT
0
DB9
DB8
DB1
DB0
3-STATE
3-STATE
B
OUT
2 Leading Zeros
Figure 11 Serial Interface Timing Diagram
CS
t2
t6
SCLK
A
3
4
5
1
2
14
15
16
17
32
t5
t10
t7
t4
DB9
t3
ZERO
DB11
DB10
DB11
B
ZERO
ZERO
ZERO
ZERO
ZERO
ZERO
0
D
A
A
A
OUT
3-STATE
3-STATE
2 Traiing Zeros,
2 Leading
Zeros,
2 Leading Zeros,
2 Traiing Zeros,
Figure 12. Reading data from Both ADCs on One DOUT Line with 32 SCLKs
Rev. PrG | Page 15 of 17
AD7266
Preliminary Technical Data
OUTLINE DIMENSIONS
5.00
0.60 MAX
BSC SQ
0.60 MAX
PIN 1
INDICATOR
25
24
32
1
PIN 1
INDICATOR
0.50
BSC
3.25
4.75
TOP
BOTTOM
VIEW
BSC SQ
3.10 SQ
2.95
VIEW
0.50
0.40
0.30
17
16
8
9
0.25 MIN
3.50 REF
0.80 MAX
12° MAX
0.65 TYP
0.05 MAX
0.02 NOM
1.00
0.85
0.80
0.30
0.23
0.18
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-220-VHHD-2
Figure 13. 32-Lead Frame Chip Scale Package [LFCSP
(CP-32)
Dimensions shown in millimeters
1.20
MAX
9.00 SQ
0.75
0.60
0.45
24
17
16
25
TOP VIEW
7.00
SQ
(PINS DOWN)
32
9
1
8
0.15
0.05
0.80
0.45
0.37
0.30
BSC
1.05
1.00
0.95
7°
0°
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MS-026ABA
Figure 14. 32-Lead Thin Flat Quad Package [TQFP]
(SU-32)
Dimensions shown in millimeters
Rev. PrG | Page 16 of 17
Preliminary Technical Data
ORDERING GUIDE
AD7266
AD7266 Products
AD7266ACP
Temperature Package
Package Description
Lead Frame Chip Scale Package
Lead Frame Chip Scale Package
Thin Quad Flat Package
Thin Quad Flat Package
Evaluation Board
Package Outline
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
CP-32
CP-32
SU-32
SU-32
AD7266BCP
AD7266ASU
AD7266BSU
EVAL-AD7266CB1
EVAL-CONTROL BRD22
Controller Board
1 This can be used as a stand-alone evaluation board or in conjunction with the EVAL-CONTROL Board for evaluation/demonstration purposes.
2 This board is a complete unit allowing a PC to control and communicate with all Analog Devices evaluation boards ending in the CB designators. To order a complete
evaluation kit, the particular ADC evaluation board, e.g., EVAL-AD7266CB, the EVAL-CONTROL BRD2, and a 12V transformer must be ordered. See relevant Evaluation
Board Technical note for more information.
©
2004 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
PR04603–0–4/04(PrG)
Rev. PrG | Page 17 of 17
相关型号:
©2020 ICPDF网 联系我们和版权申明