AD783AR [ADI]
Complete Very High Speed Sample-and-Hold Amplifier; 完整的超高速采样和保持放大器型号: | AD783AR |
厂家: | ADI |
描述: | Complete Very High Speed Sample-and-Hold Amplifier |
文件: | 总8页 (文件大小:134K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Complete Very High Speed
Sample-and-Hold Amplifier
a
AD783*
FUNCTIO NAL BLO CK D IAGRAM
FEATURES
Acquisition Tim e to 0.01%: 250 ns Typical
Low Pow er Dissipation: 95 m W
Low Droop Rate: 0.02 V/ s
Fully Specified and Tested Hold Mode Distortion
Total Harm onic Distortion: –85 dB
Aperture J itter: 50 ps Maxim um
Internal Hold Capacitor
1
2
3
4
8
OUT
V
CC
7
6
5
IN
COMMON
NC
S/H
NC
X1
Self-Correcting Architecture
8-Pin Mini Cerdip and SOIC Packages
AD783
V
EE
NC = NO CONNECT
P RO D UCT D ESCRIP TIO N
P RO D UCT H IGH LIGH TS
T he AD783 is a high speed, monolithic sample-and-hold
amplifier (SHA). T he AD783 offers a typical acquisition time
of 250 ns to 0.01%. T he AD783 is specified and tested for hold
mode total harmonic distortion with input frequencies up to
100 kHz. T he AD783 is configured as a unity gain amplifier
and uses a patented self-correcting architecture that minimizes
hold mode errors and ensures accuracy over temperature. T he
AD783 is self-contained and requires no external components
or adjustments.
1. Fast acquisition time (250 ns), low aperture jitter (20 ps) and
fully specified hold mode distortion make the AD783 an
ideal SHA for sampling systems.
2. Low droop (0.02 µV/µs) and internally compensated hold
mode error result in superior system accuracy.
3. Low power (95 mW typical), complete functionality and
small size make the AD783 an ideal choice for a variety of
high performance applications.
4. T he AD783 requires no external components or adjustments.
T he AD783 retains the held value with a droop rate of 0.02 µV/
µs. Excellent linearity and hold mode dc and dynamic perfor-
mance make the AD783 ideal for high speed 12- and 14-bit
analog-to-digital converters.
5. T he AD783 is an excellent choice as a front-end SHA for
high speed analog-to-digital converters such as the AD671,
AD7586, AD674B, AD774B, AD7572 and AD7672.
T he AD783 is manufactured on Analog Devices’ ABCMOS
process which merges high performance, low noise bipolar
circuitry with low power CMOS to provide an accurate, high
speed, low power SHA.
6. Fully specified and tested hold mode distortion guarantees
the performance of the SHA in sampled data systems.
T he J grade device is specified for operation from 0°C to +70°C
and the A grade from –40°C to +85°C. T he J and A grades are
available in 8-pin cerdip and SOIC packages. T he military
temperature range version is specified for operation from –55°C
to +125°C and is available in an 8-pin cerdip package. For
details refer to the Analog Devices Military Products Databook or
AD783/883B data sheet.
*P r otected by U.S. P atent Num ber 4,962,325.
REV. A
Inform ation furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assum ed by Analog Devices for its
use, nor for any infringem ents of patents or other rights of third parties
which m ay result from its use. No license is granted by im plication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norw ood, MA 02062-9106, U.S.A.
Tel: 617/ 329-4700
Fax: 617/ 326-8703
AD783–SPECIFICATIONS
(TMIN to TMAX with V = +5 V ؎ 5%, V = –5 V ؎ 5%, C = pF, unless otherwise noted)
DC SPECIFICATIONS
CC
EE
L
AD 783J/A
Typ
P aram eter
Min
Max
Units
SAMPLING CHARACT ERIST ICS
Acquisition T ime
5 V Step to 0.01%
5 V Step to 0.1%
Small Signal Bandwidth
Full Power Bandwidth
250
200
15
375
350
ns
ns
MHz
MHz
2
HOLD CHARACT ERIST ICS
Effective Aperture Delay (+25°C)
Aperture Jitter (+25°C)
Hold Settling (to 1 mV, +25°C)
Droop Rate
–30
15
20
150
0.02
30
50
200
1
ns
ps
ns
µV/µs
Feedthrough (+25°C)
(VIN = ±2.5 V, 500 kHz)
–80
dB
ACCURACY CHARACT ERIST ICS1
Hold Mode Offset
Hold Mode Offset Drift
Sample Mode Offset
Nonlinearity
–5
–5
0
10
50
±0.005
±0.03
+5
mV
µV/°C
mV
% FS
% FS
200
±0.1
Gain Error
OUT PUT CHARACT ERIST ICS
Output Drive Current
Output Resistance, DC
T otal Output Noise (DC to 5 MHz)
Sampled DC Uncertainty
Hold Mode Noise (DC to 5 MHz)
Short Circuit Current
Source
+5
0.6
mA
Ω
µV rms
µV rms
µV rms
0.3
150
85
125
20
13
mA
mA
Sink
INPUT CHARACT ERIST ICS
Input Voltage Range
Bias Current
Input Impedance
Input Capacitance
–2.5
2.0
+2.5
250
V
100
10
2
nA
MΩ
pF
DIGIT AL CHARACT ERIST ICS
Input Voltage Low
Input Voltage High
0.8
10
V
V
µA
Input Current High (VIN = 5 V)
2
POWER SUPPLY CHARACT ERIST ICS
Operating Voltage Range
Supply Current
+PSRR (+5 V ± 5%)
–PSRR (–5 V ± 5%)
±4.75
±5
9.5
65
65
95
±5.25
17
V
mA
dB
dB
mW
45
45
Power Consumption
175
T EMPERAT URE RANGE
Specified Performance (J)
Specified Performance (A)
0
–40
+70
+85
°C
°C
NOT ES
1Specified and tested over an input range of ±2.5 V.
Specifications subject to change without notice.
–2–
REV. A
AD783
HOLD MODE AC SPECIFICATIONS (T to TMAX with V = +5 V ؎ 5%, V = –5 V ؎ 5%, C = 50 pF, unless otherwise noted)
MIN
CC
EE
L
AD 783J/A
Typ
P aram eter
Min
Max
Units
T OT AL HARMONIC DIST ORT ION
fIN = 100 kHz
fIN = 500 kHz
–85
–72
–80
dB
dB
SIGNAL-T O-NOISE AND DIST ORT ION
fIN = 100 kHz
fIN = 500 kHz
77
70
dB
dB
INT ERMODULAT ION DIST ORT ION
(F1 = 99 kHz, F2 = 100 kHz)
Second Order Products
–80
–85
dB
dB
T hird Order Products
NOT ES
1fIN amplitude = 0 dB and fSAMPLE = 300 kHz unless otherwise indicated.
Specifications subject to change without notice.
ABSO LUTE MAXIMUM RATINGS*
With
P IN CO NFIGURATIO N
Spec
Respect to
Min
Max Units
V
1
2
3
8
7
6
OUT
S/H
NC
CC
VCC
VEE
COM
COM
COM
COM
–0.5
–6.5
–6.5
–0.5
+6.5
+0.5
+6.5
+6.5
V
V
V
V
IN
AD783
TOP VIEW
Analog Input
Digital Input
Output Short Circuit to
Ground, VCC, or VEE
Maximum Junction
T emperature
Storage
COMMON
NC
(Not to Scale)
V
5
4
EE
Indefinite
–65
NC = NO CONNECT
+175 °C
+150 °C
Lead T emperature
(10 sec max)
+300 °C
*Stresses above those listed under “Absolute Maximum Ratings” may cause
permanent damage to the device. T his is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the
operational section of this specification is not implied.
CAUTIO N
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD783 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. T herefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
O RD ERING GUID E
Tem perature
P ackage
O ptions2
Model1
Range
D escription
AD783JQ
AD783AQ
AD783JR
AD783AR
0°C to +70°C
–40°C to +85°C
0°C to +70°C
–40°C to +85°C
8-Pin Cerdip
8-Pin Cerdip
8-Pin SOIC
8-Pin SOIC
Q-8
Q-8
R-8
R-8
NOT ES
1For details on grade and package offerings screened in accordance with MIL-ST D-883, refer to the
1Analog Devices Military Products Databook or current AD783/883B data sheet.
2Q = Cerdip, R = SOIC.
REV. A
–3–
AD783–Typical Characteristics
10.0
1.0
V+
60
V–
50
40
0.1
0.01
30
0
0.001
0
25
50
75
100
125
150
1
10
100
1k
10k
100k
1M
TEMPERATURE –
°
C
FREQUENCY – Hz
Power Supply Rejection Ratio vs. Frequency
Droop Rate vs. Tem perature, VIN = 0 V
200
150
300
100
50
250
0
–50
–100
–150
–200
200
0
0
1
2
3
4
5
0
–2.5
+2.5
INPUT STEP – V
INPUT VOLTAGE – V
Acquisition Tim e (to 0.01%) vs. Input Step Size
Bias Current vs. Input Voltage
–4–
REV. A
AD783
O utput D r ive Cur r ent—T he maximum current the SHA can
source (or sink) while maintaining a change in hold mode offset
of less than 2.5 mV.
D EFINITIO NS O F SP ECIFICATIO NS
Acquisition Tim e—T he length of time that the SHA must
remain in the sample mode in order to acquire a full-scale input
step to a given level of accuracy.
Signal-To-Noise and D istor tion (S/N+D ) Ratio—S/N+D is
the ratio of the rms value of the measured input signal to the
rms sum of all other spectral components below the Nyquist
frequency, including harmonics but excluding dc. T he value for
S/N+D is expressed in decibels.
Sm all Signal Bandwidth—T he frequency at which the held
output amplitude is 3 dB below the input amplitude, under an
input condition of a 100 mV p-p sine wave.
Full P ower Bandwidth—T he frequency at which the held
output amplitude is 3 dB below the input amplitude, under an
input condition of a 5 V p-p sine wave.
Total H ar m onic D istor tion (TH D )—T HD is the ratio of the
rms sum of the first six harmonic components to the rms value
of the measured input signal and is expressed in decibels.
Effective Aper tur e D elay—T he difference between the switch
delay and the analog delay of the SHA channel. A negative
number indicates that the analog portion of the overall delay is
greater than the switch portion. T his effective delay represents
the point in time, relative to the hold command, that the input
signal will be sampled.
Inter m odulation D istor tion (IMD )—With inputs consisting
of sine waves at two frequencies, fa and fb, any device with
nonlinearities will create distortion products, of order (m+n), at
sum and difference frequency of mfa±nfb, where m, n = 0, 1, 2,
3. . . . Intermodulation terms are those for which m or n is not
equal to zero. For example, the second order terms are (fa+fb)
and (fa–fb), and the third order terms are (2fa+fb), (2fa–fb),
(fa+2fb) and (fa–2fb). T he IMD products are expressed as the
decibel ratio of the rms sum of the measured input signals to the
rms sum of the distortion terms. T he two signals are of equal
amplitude, and peak value of their sums is –0.5 dB from full
scale. T he IMD products are normalized to a 0 dB input signal.
Aper tur e Jitter—T he variations in aperture delay for
successive samples. Aperture jitter puts an upper limit on the
maximum frequency that can be accurately sampled.
H old Settling Tim e—T he time required for the output to
settle to within a specified level of accuracy of its final held value
after the hold command has been given.
D r oop Rate—T he drift in output voltage while in the hold
mode.
FUNCTIO NAL D ESCRIP TIO N
T he AD783 is a complete, high speed sample-and-hold
amplifier that provides high speed sampling to 12-bit accuracy
in 250 ns.
Feedthr ough—T he attenuated version of a changing input
signal that appears at the output when the SHA is in the hold
mode.
T he AD783 is completely self-contained, including an on-chip
hold capacitor, and requires no external components or adjust-
ments to perform the sampling function. Both input and output
are treated as a single-ended signal, referred to common.
H old Mode O ffset—T he difference between the input signal
and the held output. T his offset term applies only in the hold
mode and includes the error caused by charge injection and all
other internal offsets. It is specified for an input of 0 V.
T he AD783 utilizes a proprietary circuit design which includes a
self-correcting architecture. T his sample-and-hold circuit
corrects for internal errors after the hold command has been
given, by compensating for amplifier gain and offset errors, and
charge injection errors. Due to the nature of the design, the
SHA output in the sample mode is not intended to provide an
accurate representation of the input. However, in hold mode,
the internal circuitry is reconfigured to produce an accurately
held version of the input signal. Below is a block diagram of the
AD783.
Sam ple Mode O ffset—T he difference between the input and
output signals when the SHA is in the sample mode.
Nonlinear ity—T he deviation from a straight line on a plot of
input vs. (held) output as referenced to a straight line drawn
between endpoints, over an input range of –2.5 V and +2.5 V.
Gain Er r or—Deviation from a gain of +1 on the transfer
function of input vs. held output.
P ower Supply Rejection Ratio—A measure of change in the
held output voltage for a specified change in the positive or
negative supply.
1
2
3
4
8
OUT
V
Sam pled D C Uncer tainty—T he internal rms SHA noise that
is sampled onto the hold capacitor.
CC
7
6
5
IN
COMMON
NC
S/H
NC
X1
H old Mode Noise—T he rms noise at the output of the SHA
while in the hold mode, specified over a given bandwidth.
Total O utput Noise—T he total rms noise that is seen at the
output of the SHA while in the hold mode. It is the rms
summation of the sampled dc uncertainty and the hold mode
noise.
AD783
V
EE
NC = NO CONNECT
Functional Block Diagram
REV. A
–5–
AD783
D YNAMIC P ERFO RMANCE
(V
HOLD – V ), mV
IN
OUT
T he AD783 is compatible with 12-bit A-to-D converters in
terms of both accuracy and speed. T he fast acquisition time, fast
hold settling time and good output drive capability allow the
AD783 to be used with high speed, high resolution A-to-D
converters like the AD671 and AD7586. T he AD783’s fast
acquisition time provides high throughput rates for multichannel
data acquisition systems. T ypically, the AD783 can acquire a
5 V step in less than 250 ns. Figure 1 shows the settling
accuracy as a function of acquisition time.
+1
V
, VOLTS
+2.5
IN
–2.5
NONLINEARITY
0.08
HOLD MODE OFFSET
–1
GAIN ERROR
0.06
0.04
Figure 2. Hold Mode Offset, Gain Error and Nonlinearity
0.02
0
For applications where it is important to obtain zero offset, the
hold mode offset may be nulled externally at the input to the
A-to-D converter. Adjustment of the offset may be accom-
plished through the A-to-D itself or by an external amplifier
with offset nulling capability (e.g., AD711). T he offset will
change less than 0.5 mV over the specified temperature range.
250
500
0
ACQUISITION TIME – ns
Figure 1. VOUT Settling vs. Acquisition Tim e
T he hold settling determines the required time, after the hold
command is given, for the output to settle to its final specified
accuracy. T he typical settling behavior of the AD783 is 150 ns.
T he settling time of the AD783 is sufficiently fast to allow the
SHA, in most cases, to directly drive an A-to-D converter
without the need for an added “start convert” delay.
SUP P LY D ECO UP LING AND GRO UND ING
CO NSID ERATIO NS
As with any high speed, high resolution data acquisition system,
the power supplies should be well regulated and free from
excessive high frequency noise (ripple). T he supply connection
to the AD783 should also be capable of delivering transient
currents to the device. T o achieve the specified accuracy and
dynamic performance, decoupling capacitors must be placed
directly at both the positive and negative supply pins to com-
mon. Ceramic type 0.1 µF capacitors should be connected from
VCC and VEE to common.
H O LD MO D E O FFSET
T he dc accuracy of the AD783 is determined primarily by the
hold mode offset. T he hold mode offset refers to the difference
between the final held output voltage and the input signal at the
time the hold command is given. T he hold mode offset arises
from a voltage error introduced onto the hold capacitor by
charge injection of the internal switches. T he nominal hold
mode offset is specified for a 0 V input condition. Over the in-
put range of –2.5 V to +2.5 V, the AD783 is also characterized
for an effective gain error and nonlinearity of the held value, as
shown in Figure 2. As indicated by the AD783 specifications,
the hold mode offset is very stable over temperature.
ANALOG
P.S.
DIGITAL
P.S.
+5V
C
–5V
C
+5V
0.1µF 0.1µF
1µF
1µF
1µF
INPUT
DIGITAL
DATA
OUTPUT
ANALOG-TO-DIGITAL
CONVERTER
AD783
SIGNAL GROUND
Figure 3. Basic Grounding and Decoupling Diagram
–6–
REV. A
AD783
T he AD783 does not provide separate analog and digital ground
leads as is the case with most A-to-D converters. T he common
pin is the single ground terminal for the device. It is the refer-
ence point for the sampled input voltage and the held output
voltage and also the digital ground return path. T he common
pin should be connected to the reference (analog) ground of the
A-to-D converter with a separate ground lead. Since the analog
and digital grounds in the AD783 are connected internally, the
common pin should also be connected to the digital ground,
which is usually tied to analog common at the A-to-D converter.
Figure 3 illustrates the recommended decoupling and grounding
practice.
T he accuracy in sampling high frequency signals is also
constrained by the distortion and noise created by the
sample-and-hold. T he level of distortion increases with
frequency and reduces the “effective number of bits” of the
conversion.
Measurements of Figures 6 and 7 were made using a 14-bit
A/D converter with VIN = 5 V p-p and a sample frequency of
100 kSPS.
1%
1/2 BIT @
8 BITS
NO ISE CH ARACTERISTICS
Designers of data conversion circuits must also consider the
effect of noise sources on the accuracy of the data acquisition
system. A sample-and-hold amplifier that precedes the A-to-D
converter introduces some noise and represents another source
of uncertainty in the conversion process. T he noise from the
AD783 is specified as the total output noise, which includes
both the sampled wideband noise of the SHA in addition to the
band limited output noise. T he total output noise is the rms
sum of the sampled dc uncertainty and the hold mode noise. A
plot of the total output noise vs. the equivalent input bandwidth
of the converter being used is given in Figure 4.
0.1%
1/2 BIT @
10 BITS
1/2 BIT @
12 BITS
APERTURE JITTER TYPICAL AT 20ps
0.01%
1/2 BIT @
14 BITS
1k
10k
100k
1M
FREQUENCY – Hz
300
200
100
0
Figure 5. Error Magnitude vs. Frequency
–65
–70
–75
–80
–85
–90
1k
10k
100k
1M
10M
FREQUENCY – Hz
–95
100
1k
10k
100k
1M
Figure 4. RMS Noise vs. Input Bandwidth of ADC
FREQUENCY – Hz
D RIVING TH E ANALO G INP UTS
Figure 6. Total Harm onic Distortion vs. Frequency
For best performance, it is important to drive the AD783 analog
input from a low impedance signal source. T his enhances the
sampling accuracy by minimizing the analog and digital cross-
talk. Signals which come from higher impedance sources (e.g.,
over 5 kΩ) will have a relatively higher level of crosstalk. For
applications where signals have high source impedance, an
operational amplifier buffer in front of the AD783 is required.
T he AD711 (precision BiFET op amp) is recommended for
these applications.
90
80
70
60
50
40
30
20
10
0
H IGH FREQ UENCY SAMP LING
Aperture jitter and distortion are the primary factors which limit
frequency domain performance of a sample-and-hold amplifier.
Aperture jitter modulates the phase of the hold command and
produces an effective noise on the sampled analog input. T he
magnitude of the jitter induced noise is directly related to the
frequency of the input signal.
1k
10k
100k
1M
FREQUENCY – Hz
A graph showing the magnitude of the jitter induced error vs.
frequency of the input signal is given in Figure 5.
Figure 7. Signal/(Noise and Distortion) vs. Frequency
REV. A
–7–
AD783
AD 783 TO AD 670 INTERFACE
T he low going one-shot output is connected to the clock input
of flip-flop2. T he D2 input of flip-flop2 is tied high. T he rising
edge of the low going pulse toggles the Q2 output of flip-flop2 to
a high state. T his output, which is tied to the ENCODE input of
the AD671, initiates a conversion of the buffered output signal
of the AD783. T he AD671 issues the signal DAV when the con-
version is complete. T he DAV signal is tied to the asynchronous
CLR1 and CLR2 inputs of both flip-flops. When DAV goes low,
the Q1 output goes high returning the AD783 to the sample or
acquisition mode. T he Q2 output (ENCODE) returns low until
it is again triggered by the rising edge of the one-shot output.
T he 15 MHz small signal bandwidth of the AD783 makes it a
good choice for undersampling applications. Figure 8 shows
the interface between the AD783 and the AD670 ADC, where
the AD783 samples the incoming IF signal. For this particular
application, the IF carrier was 10.7 MHz and the information
signal was a 5 kHz FSK-modulated tone. T he sample-and-hold
signal is applied to the 8-bit AD670 ADC and then digitally
processed for analysis.
T he CLKIN signal is connected directly to the S/H pin of the
AD783 and must comply with the acquisition and settling re-
quirements of the SHA. A delayed version of CLKIN is applied
to the R/W input of the AD670 in order to accommodate the
hold-mode settling requirements of the AD783. T he 10 µs con-
version speed of the AD670 combined with the 150 ns hold-
mode settling time of the AD783 result in a total system
throughput of 10.15 µs.
V
IN
AD783
AIN
AD84X
AD671
CLOCK
Q1
CLR1
CLR2
Q2
D1
D2
By keeping the 10.7 MHz IF input to the AD783 at a low
amplitude, 255 mV p-p, the resultant distortion and jitter-
induced noise result in approximately 45 dB of dynamic range.
T he AD670 can be conveniently configured such that its full-
scale input range is 255 mV in order to retain the full 8-bit
dynamic range of the converter. T he maximum sample rate of
the AD670 is 10 µs; therefore, to comply with the Nyquist
criteria the maximum information bandwidth is 50 kHz.
+5V
DAV
ONE-
SHOT
ENCODE
Figure 9. AD783 to AD671 Interface
O UTLINE D IMENSIO NS
D imensions shown in inches and (mm).
8-P in Cerdip (Q-8) P ackage
10k
2
8
ANALOG
INPUT
AD783
7
18 +V HI
IN
50
10.7MHz
+V LOW
IN
19
8
1
5
255mV p-p
0.310 (7.87)
0.220 (5.59)
16
17
–V HI
IN
CLK IN
–V LOW
IN
4
AD670
0.320 (8.13)
0.290 (7.37)
0.405 (10.29)
MAX
ONE -
SHOT
21 R/W
0.060 (1.52)
0.015 (0.38)
0.200
(5.08)
MAX
Figure 8. AD783 to AD670 Interface
0.150
(3.81)
MIN
0.015 (0.381)
0.008 (0.204)
AD 783 to AD 671 (12-Bit, 500 ns AD C) Inter face
T he AD783 to AD671 interface requires an op amp, a dual
flip-flop, and a monostable multivibrator or “one-shot.” T he
op amp amplifies the ±2.5 V output of the AD783 to the
full-scale input of the AD671. Appropriate op amps include the
AD841 and AD845 (see the AD671 data sheet for additional
information). T he flip-flops and one-shot are used to generate
the AD671 ENCODE pulse and the appropriately timed
AD783 S/H pulse.
0.023 (0.58)
0.014 (0.36)
0.100 (2.54)
BSC
0.070 (1.78)
0.030 (0.76)
8-P in SO IC (R-8) P ackage
0.198 (5.03)
0.188 (4.77)
A master sampling clock is tied to the clock input of flip-flop1
and the input of the one-shot. T he D1 input of flip-flop1
should be tied high and the one-shot should be configured to
generate a pulse on a rising edge of the sampling clock. T he ris-
ing edge of the sampling clock causes the Q1 output of the
flip-flop to go low placing the AD783 into hold mode. Simulta-
neously, a low going pulse is generated at the one-shot output.
T he length of this pulse would usually be made long enough to
allow the output of the AD783 to settle (hold-mode settling
time), but because of the error-correcting ability of the AD671,
the length of this pulse may be reduced to approximately 200 ns.
5
8
0.158 (4.01)
0.150 (3.81)
0.248 (6.29)
0.224 (5.69)
4
1
0.022 (0.56)
0.014 (0.36)
0.205 (5.21)
0.195 (4.95)
0.050 (1.27)
BSC
0.107 (2.72)
0.089 (2.26)
0.011 (0.275)
0.005 (0.125)
0.034 (0.86)
0.018 (0.46)
0.015 (0.38)
0.007 (0.18)
–8–
REV. A
相关型号:
AD783JN
IC SAMPLE AND HOLD AMPLIFIER, 0.155 us ACQUISITION TIME, PDIP8, MINI, PLASTIC, DIP-8, Sample and Hold Circuit
ADI
AD783SQ
IC SAMPLE AND HOLD AMPLIFIER, 0.15 us ACQUISITION TIME, CDIP8, MINI, CERDIP-8, Sample and Hold Circuit
ADI
AD7840ACHIPS
IC SERIAL, PARALLEL, WORD INPUT LOADING, 2.5 us SETTLING TIME, 14-BIT DAC, UUC, DIE, Digital to Analog Converter
ADI
AD7840ARSZ
SERIAL, PARALLEL, WORD INPUT LOADING, 2.5 us SETTLING TIME, 14-BIT DAC, PDSO24, SSOP-24
ROCHESTER
©2020 ICPDF网 联系我们和版权申明