AD7893AR-10REEL [ADI]
1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8, SOIC-8;
| 型号： | AD7893AR-10REEL |
| 厂家： | 
ADI |
| 描述： | 1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8, SOIC-8 信息通信管理 光电二极管 转换器 |
| 文件： | 总14页 (文件大小：349K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LC2MOS 12-Bit, Serial 6 s
a
ADC in 8-Pin Package
AD7893
FUNCTIONAL BLOCK DIAGRAM
FEATURES
Fast 12-Bit ADC with 6 s Conversion Time
8-Pin Mini-DlP and SOIC
Single Supply Operation
High Speed, Easy-to-Use, Serial Interface
On-Chip Track/Hold Amplifier
Selection of Input Ranges
؎10 V for AD7893-10
REF IN
V
DD
AD7893
TRACK/
HOLD
SIGNAL
SCALING*
V
IN
12-BIT
ADC
؎2.5 V for AD7893-3
0 V to +2.5 V for AD7893-2
0 V to +5 V for AD7893-5
Low Power: 25 mW typ
OUTPUT
REGISTER
CONVST
AGND DGND
SCLK SDATA
*AD7893-5, AD7893-10, AD7893-3
PRODUCT HIGHLIGHTS
1. Fast, 12-Bit ADC in 8-Pin Package
GENERAL DESCRIPTION
The AD7893 is a fast, 12-bit ADC that operates from a single
+5 V supply and is housed in a small 8-pin mini-DIP and 8-pin
SOIC. The part contains a 6 µs successive approximation A/D
converter, an on-chip track/hold amplifier, an on-chip clock and
a high speed serial interface.
The AD7893 contains a 6 µs ADC, a track/hold amplifier,
control logic and a high speed serial interface, all in an 8-pin
package. This offers considerable space saving over alterna-
tive solutions.
2. Low Power, Single Supply Operation
Output data from the AD7893 is provided via a high speed,
serial interface port. This two-wire serial interface has a serial
clock input and a serial data output with the external serial clock
accessing the serial data from the part.
The AD7893 operates from a single +5 V supply and con-
sumes only 25 mW. This low power, single supply operation
makes it ideal for battery powered or portable applications.
3. High Speed Serial Interface
In addition to traditional dc accuracy specifications such as lin-
earity, full-scale and offset errors, the AD7893 is also specified
for dynamic performance parameters, including harmonic dis-
tortion and signal-to-noise ratio.
The part provides high speed serial data and serial clock lines,
allowing for an easy, two-wire serial interface arrangement.
The part accepts an analog input range of ±10 V (AD7893-10),
±2.5 V (AD7893-3), 0 V to +5 V (AD7893-5) or 0 V to +2.5 V
(AD7893-2) and operates from a single +5 V supply, consuming
only 25 mW typical.
The AD7893 is fabricated in Analog Devices’ Linear Compat-
ible CMOS (LC2MOS) process, a mixed technology process
that combines precision bipolar circuits with low power CMOS
logic. The part is available in a small, 8-pin, 0.3" wide, plastic or
hermetic dual-in-line package (mini-DIP) and in an 8-pin, small
outline IC (SOIC).
REV. E
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 617/329-4700
Fax: 617/326-8703
World Wide Web Site: http://www.analog.com
© Analog Devices, Inc., 1997
(VDD = +5 V, AGND = DGND = 0 V, REF IN = +2.5 V. All specifications TMIN to TMAX unless
AD7893–SPECIFICATIONS otherwise noted.)
A
B
S
Parameter
Versionsl
Versions
Version
Units
Test Conditions/Comments
DYNAMIC PERFORMANCE
Signal to (Noise + Distortion) Ratio2
@ +25°C
70
–80
–80
70
–80
–80
70
–80
–80
dB min
dB max
dB max
fIN = 10 kHz Sine Wave, fSAMPLE = 117 kHz
fIN = 10 kHz Sine Wave, fSAMPLE = 117 kHz
fIN = 10 kHz Sine Wave, fSAMPLE = 117 kHz
fa = 9 kHz, fb = 9.5 kHz, fSAMPLE = 117 kHz
Total Harmonic Distortion (THD)2
Peak Harmonic or Spurious Noise2
Intermodulation Distortion (IMD)2
2nd Order Terms
–80
–80
–80
–80
–80
–80
dB max
dB max
3rd Order Terms
DC ACCURACY
Resolution
12
12
12
Bits
Minimum Resolution for which
No Missing Codes are Guaranteed
Relative Accuracy2
12
±1
±1
±3
12
±1/2
±1
12
±1
±1
±3
Bits
LSB max
LSB max
LSB max
Differential Nonlinearity2
Positive Full-Scale Error2
AD7893-2, AD7893-5
Unipolar Offset Error
AD7893-10, AD7893-3
Negative Full-Scale Error2
Bipolar Zero Error
±1.5
±4
±3
±4
LSB max
±3
±4
±1.5
±2
±3
±4
LSB max
LSB max
ANALOG INPUT
AD7893-10
Input Voltage Range
Input Resistance
AD7893-3
±10
16
±10
16
±10
16
Volts
kΩ min
Input Voltage Range
Input Resistance
AD7893-5
±2.5
4
±2.5
4
±2.5
4
Volts
kΩ min
Input Voltage Range
Input Resistance
AD7893-2
0 to +5
9
0 to +5
9
0 to +5
9
Volts
kΩ min
Input Voltage Range
Input Current
0 to +2.5
500
0 to +2.5
500
0 to +2.5
500
Volts
nA max
REFERENCE INPUT
REF IN Input Voltage Range
Input Current
2.375/2.625 2.375/2.625 2.375/2.625 V min/V max 2.5 V ± 5%
2
2
10
10
µA max
Input Capacitance3
10
10
pF max
LOGIC INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
2.4
0.8
±10
10
2.4
0.8
±10
10
2.4
0.8
±10
10
V min
VDD = 5 V ± 5%
VDD = 5 V ± 5%
VIN = 0 V to VDD
V max
µA max
pF max
3
Input Capacitance, CIN
LOGIC OUTPUTS
Output High Voltage, VOH
Output Low Voltage, VOL
Output Coding
4.0
0.4
4.0
0.4
4.0
0.4
V min
V max
ISOURCE = 200 µA
ISINK = 1.6 mA
AD7893-10, AD7893-3
AD7893-2, AD7893-5
2s Complement
Straight (Natural) Binary
CONVERSION RATE
Conversion Time
6
1.5
6
1.5
6
1.5
µs max
µs max
Track/Hold Acquisition Time2
POWER REQUIREMENTS
VDD
IDD
+5
9
45
+5
9
45
+5
9
45
V nom
mA max
mW max
±5% for Specified Performance
Power Dissipation
Typically 25 mW
NOTES
1Temperature Ranges are as follows: A, B Versions: –40°C to +85°C, S Version: –55°C to +125°C.
2See Terminology.
3Sample tested @ +25°C to ensure compliance.
Specifications subject to change without notice.
–2–
REV. E
AD7893
TIMING CHARACTERISTICS1, 2
(VDD = +5 V, AGND = DGND = 0 V, REF IN = +2.5 V)
A, B
S
Parameter
Versions
Version
Units
Test Conditions/Comments
t1
t2
50
60
30
50
10
100
50
70
40
60
10
100
ns min
ns min
ns min
ns max
ns min
ns max
CONVST Pulse Width
SCLK High Pulse Width
SCLK Low Pulse Width
SCLK Rising Edge to Data Valid Delay
Bus Relinquish Time after Falling Edge of SCLK
t33
t4
4
t5
NOTES
1 Sample tested at +25°C to ensure compliance. All input signals are measured with tr = tf = 1 ns (10% to 90% of +5 V) and timed from a voltage level of +1.6 V.
2 See Figure 5.
3 Measured with the load circuit of Figure 1 and defined as the time required for an output to cross 0.8 V or 2.4 V.
4 Derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit of Figure 1. The measured number is then extrapolated back
to remove the effects of charging or discharging the 50 pF capacitor. This means that the time, t5, quoted in the timing characteristics is the true bus relinquish time
of the part and, as such, is independent of external bus loading capacitances.
ABSOLUTE MAXIMUM RATINGS*
(TA = +25°C unless otherwise noted)
VDD to AGND . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
1.6mA
V
DD to DGND . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
Analog Input Voltage to AGND
AD7893-10, AD7893-5 . . . . . . . . . . . . . . . . . . . . . . . ±17 V
AD7893-2, AD7893-3 . . . . . . . . . . . . . . . . . . . –5 V, +10 V
Reference Input Voltage to AGND . . . –0.3 V to VDD + 0.3 V
Digital Input Voltage to DGND . . . . . –0.3 V to VDD + 0.3 V
Digital Output Voltage to DGND . . . . –0.3 V to VDD + 0.3 V
Operating Temperature Range
TO
OUTPUT
PIN
+2.1V
50pF
200µA
Commercial (A, B Versions) . . . . . . . . . . . –40°C to +85°C
Extended (S Version) . . . . . . . . . . . . . . . . –55°C to +125°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . +150°C
Plastic DIP Package, Power Dissipation . . . . . . . . . . 450 mW
θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 130°C/W
Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . +260°C
Cerdip Package, Power Dissipation . . . . . . . . . . . . . . 450 mW
θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 125°C/W
Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . +300°C
SOIC Package, Power Dissipation . . . . . . . . . . . . . . . 450 mW
θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 170°C/W
Lead Temperature, Soldering
Figure 1. Load Circuit for Access Time and Bus
Relinquish Time
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . +215°C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . +220°C
*Stresses above those listed under “Absolute Maximum Ratings” may cause
permanent damage to the device. This is a stress rating only; functional operation
of the device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the AD7893 features proprietary ESD protection circuitry, permanent damage may occur on devices
subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
REV. E
–3–
AD7893
PIN FUNCTION DESCRIPTION
Pin Pin
No. Mnemonic
Description
1
REF IN
Voltage Reference Input. An external reference source should be connected to this pin to provide the refer-
ence voltage for the AD7893’s conversion process. The REF IN input is buffered on-chip. The nominal ref-
erence voltage for correct operation of the AD7893 is +2.5 V.
2
VIN
Analog Input Channel. The analog input range is ±10 V (AD7893-10), ±2.5 V (AD7893-3), 0 V to +5 V
(AD7893-5) and 0 V to +2.5 V (AD7893-2).
3
4
AGND
SCLK
Analog Ground. Ground reference for track/hold, comparator and DAC.
Serial Clock Input. An external serial clock is applied to this input to obtain serial data from the AD7893. A
new serial data bit is clocked out on the rising edge of this serial clock, and data is valid on the falling edge.
The serial clock input should be taken low at the end of the serial data transmission.
5
SDATA
Serial Data Output. Serial data from the AD7893 is provided at this output. The serial data is clocked out by
the rising edge of SCLK and is valid on the falling edge of SCLK. Sixteen bits of serial data are provided
with four leading zeros followed by the 12 bits of conversion data. On the sixteenth falling edge of SCLK, the
SDATA line is disabled (three-stated). Output data coding is twos complement for the AD7893-10 and
AD7893-3, straight binary for the AD7893-2 and AD7893-5.
6
7
DGND
Digital Ground. Ground reference for digital circuitry.
CONVST
Convert Start. Edge-triggered logic input. On the falling edge of this input, the serial clock counter is reset to
zero. On the rising edge of this input, the track/hold goes into its hold mode and conversion is initiated.
8
VDD
Positive supply voltage, +5 V ± 5%.
PIN CONFIGURATION
DIP and SOIC
REF IN
V
1
2
3
4
8
7
6
5
DD
V
CONVST
DGND
IN
AD7893
TOP VIEW
(NOT TO SCALE)
AGND
SCLK
SDATA
ORDERING GUIDE
Temperature
Range
Linearity
Error
Package
Options*
Model
SNR
AD7893AN-2 –40°C to +85°C
±1 LSB
70 dB N-8
AD7893BN-2
AD7893AR-2
AD7893BR-2
AD7893SQ-2
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
±1/2 LSB 72 dB N-8
±1 LSB 70 dB SO-8
±1/2 LSB 72 dB SO-8
–55°C to +125°C ±1 LSB
70 dB Q-8
AD7893AN-5 –40°C to +85°C
±1 LSB
70 dB N-8
AD7893BN-5
AD7893AR-5
AD7893BR-5
AD7893SQ-5
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
±1/2 LSB 72 dB N-8
±1 LSB 70 dB SO-8
±1/2 LSB 72 dB SO-8
–55°C to +125°C ±1 LSB
70 dB Q-8
AD7893AN-10 –40°C to +85°C
AD7893BN-10 –40°C to +85°C
AD7893AR-10 –40°C to +85°C
AD7893BR-10 –40°C to +85°C
±1 LSB
70 dB N-8
±1/2 LSB 72 dB N-8
±1 LSB 70 dB SO-8
±1/2 LSB 72 dB SO-8
AD7893SQ-10 –55°C to +125°C ±1 LSB
70 dB Q-8
AD7893AR-3 –40°C to +85°C ±1 LSB
70 dB SO-8
*N = Plastic DIP, Q = Cerdip, SO = SOIC.
–4–
REV. E
AD7893
TERMINOLOGY
Relative Accuracy
Signal to (Noise + Distortion) Ratio
Relative accuracy or endpoint nonlinearity is the maximum
deviation from a straight line passing through the endpoints of
the ADC transfer function.
This is the measured ratio of signal to (noise + distortion) at the
output of the A/D converter. The signal is the rms amplitude of
the fundamental. Noise is the rms sum of all nonfundamental
signals up to half the sampling frequency (fS/2), excluding dc.
The ratio is dependent upon the number of quantization levels
in the digitization process; the more levels, the smaller the quan-
tization noise. The theoretical signal to (noise + distortion) ratio
for an ideal N-bit converter with a sine wave input is given by:
Differential Nonlinearity
This is the difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Positive Full-Scale Error (AD7893-10)
This is the deviation of the last code transition (01 . . . 110 to
01 . . . 111) from the ideal 4 × REF IN – 1 LSB (AD7893-10
±10 V range) after the Bipolar Zero Error has been adjusted out.
Signal to (Noise + Distortion) = (6.02 N + 1.76) dB
Thus for a 12-bit converter, this is 74 dB.
Positive Full-Scale Error (AD7893-3)
Total Harmonic Distortion
Total harmonic distortion (THD) is the ratio of the rms sum of
harmonics to the fundamental. For the AD7893, it is defined as:
This is the deviation of the last code transition (01 . . . 110 to
01 . . . 111) from the ideal (REF IN – 1 LSB) after the
Bipolar Zero Error has been adjusted out.
Positive Full-Scale Error (AD7893-5)
V22 +V32 +V42 +V52 +V62
This is the deviation of the last code transition (11 . . . 110 to
11 . . . 111) from the ideal (2 × REF IN – 1 LSB) after the Uni-
polar Offset Error has been adjusted out.
THD(dB) = 20 log
V1
where V1 is the rms amplitude of the fundamental and V2, V3,
V4, V5 and V6 are the rms amplitudes of the second through the
sixth harmonics.
Positive Full-Scale Error (AD7893-2)
This is the deviation of the last code transition (11 . . . 110 to
11 . . . 111) from the ideal (REF IN – 1 LSB) after the Unipolar
Offset Error has been adjusted out.
Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to fS/2 and excluding dc) to the rms value of the
fundamental. Normally, the value of this specification is deter-
mined by the largest harmonic in the spectrum, but for parts
where the harmonics are buried in the noise floor, it will be a
noise peak.
Bipolar Zero Error (AD7893-10, ؎10 V; AD7893-3, ؎2.5 V)
This is the deviation of the midscale transition (all 0s to all 1s)
from the ideal 0 V (AGND).
Unipolar Offset Error (AD7893-2, AD7893-5)
This is the deviation of the first code transition (00 . . . 000 to
00 . . . 001) from the ideal 1 LSB.
Negative Full-Scale Error (AD7893-10)
Intermodulation Distortion
This is the deviation of the first code transition (10 . . . 000 to
10 . . . 001) from the ideal –4 × REF IN + 1 LSB (AD7893-10
±10 V range) after Bipolar Zero Error has been adjusted out.
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities will create distortion
products at sum and difference frequencies of mfa ± nfb where
m, n = 0, 1, 2, 3, etc. Intermodulation terms are those for
which neither m nor n are equal to zero. For example, the second
order terms include (fa + fb) and (fa – fb), while the third order
terms include (2 fa + fb), (2 fa – fb), (fa + 2 fb) and (fa – 2 fb).
Negative Full-Scale Error (AD7893-3)
This is the deviation of the first code transition (10 . . . 000 to
10 . . . 001) from the ideal (–REF IN + 1 LSB) after Bipolar
Zero Error has been adjusted out.
The AD7893 is tested using the CCIF standard where two
input frequencies near the top end of the input bandwidth are
used. In this case, the second and third order terms are of differ-
ent significance. The second order terms are usually distanced
in frequency from the original sine waves, while the third order
terms are usually at a frequency close to the input frequencies.
As a result, the second and third order terms are specified sepa-
rately. The calculation of the intermodulation distortion is per
the THD specification where it is the ratio of the rms sum of the
individual distortion products to the rms amplitude of the fun-
damental expressed in dBs.
Track/Hold Acquisition Time
Track/Hold acquisition time is the time required for the output
of the track/hold amplifier to reach its final value, within
±1/2 LSB, after the end of conversion (the point at which the
track/hold returns to track mode). It also applies to situations
where there is a step input change on the input voltage applied
to the VIN input of the AD7893. This means that the user must
wait for the duration of the track/hold acquisition time after the
end of conversion or after a step input change to VIN before
starting another conversion, to ensure that the part operates to
specification.
REV. E
–5–
AD7893
amplifier. For the AD7893-10, R1 = 30 kΩ; R2 = 7.5 kΩ and
R3 = 10 kΩ. For the AD7893-3, R1 = R2 = 6.5 kΩ, and R3
is open circuit. For the AD7893-5, R1 and R3 = 5 kΩ while
R2 is open-circuit.
CONVERTER DETAILS
The AD7893 is a fast, 12-bit single supply A/D converter. It
provides the user with signal scaling (AD7893-10), track/hold,
A/D converter and serial interface logic functions on a single
chip. The A/D converter section of the AD7893 consists of a
conventional successive-approximation converter based on an
R-2R ladder structure. The signal scaling on the AD7893-10,
AD7893-5 and AD7893-3 allows the part to handle ±10 V, 0 V
to +5 V and ±2.5 V input signals, respectively, while operating
from a single +5 V supply. The AD7893-2 accepts an analog in-
put range of 0 V to +2.5 V. The part requires an external +2.5 V
reference. The reference input to the part is buffered on-chip.
For the AD7893-10 and AD7893-3, the designed code transi-
tions occur on successive integer LSB values (i.e., 1 LSB, 2 LSBs,
3 LSBs . . .). Output coding is twos complement binary with
1 LSB = FS/4096. The ideal input/output transfer function for
the AD7893-10 and AD7893-3 is shown in Table I.
Table I. Ideal Input/Output Code Table for the AD7893-10/
AD7893-3
A major advantage of the AD7893 is that it provides all of the
above functions in an 8-pin package, either 8-pin mini-DIP or
SOIC. This offers the user considerable space saving advantages
over alternative solutions. The AD7893 typically consumes only
25 mW, making it ideal for battery-powered applications.
Digital Output
Code Transition
Analog Input1
+FSR/2 – 1 LSB2
+FSR/2 – 2 LSBs
+FSR/2 – 3 LSBs
011 . . . 110 to 011 . . . 111
011 . . . 101 to 011 . . . 110
011 . . . 100 to 011 . . . 101
Conversion is initiated on the AD7893 by pulsing the CONVST
input. On the rising edge of CONVST, the on-chip track/hold
goes from track-to-hold mode and the conversion sequence is
started. The conversion clock for the part is generated internally
using a laser-trimmed clock oscillator circuit. Conversion time
for the AD7893 is 6 µs, and the track/hold acquisition time is
1.5 µs. To obtain optimum performance from the part, the read
operation should not occur during the conversion or during
600 ns prior to the next conversion. This allows the part to op-
erate at throughput rates up to 117 kHz and to achieve data
sheet specifications. The part can operate at higher throughput
rates (up to 133 kHz) with slightly degraded performance (see
Timing and Control section).
AGND + 1 LSB
AGND
AGND – 1 LSB
000 . . . 000 to 000 . . . 001
111 . . . 111 to 000 . . . 000
111 . . . 110 to 111 . . . 111
–FSR/2 + 3 LSBs
–FSR/2 + 2 LSBs
–FSR/2 + 1 LSB
100 . . . 010 to 100 . . . 011
100 . . . 001 to 100 . . . 010
100 . . . 000 to 100 . . . 001
NOTES
1FSR is full-scale range and is 20 V (AD7893-10) and = 5 V (AD7893-3) with
REF IN = +2.5 V.
21 LSB = FSR/4096 = 4.883 mV (AD7893-10) and 1.22 mV (AD7893-3) with
REF IN = +2.5 V.
For the AD7893-5, the designed code transitions occur again on
successive integer LSB values. Output coding is straight (natural)
binary with 1 LSB = FS/4096 = 5 V/4096 = 1.22 mV. The ideal
input/output transfer function for the AD7893-5 is shown in
Table II.
CIRCUIT DESCRIPTION
Analog Input Section
The AD7893 is offered as four part types: the AD7893-10,
which handles a ±10 V input voltage range; the AD7893-3,
which handles a ±2.5 V input voltage range; the AD7893-5,
which handles a 0 V to +5 V input range; and the AD7893-2,
which handles a 0 V to +2.5 V input voltage range.
The analog input section for the AD7893-2 contains no biasing
resistors, and the VIN pin drives the input directly to the track/
hold amplifier. The analog input range is 0 V to +2.5 V into a
high impedance stage, with an input current of less than
500 nA. This input is benign, with no dynamic charging cur-
rents. Once again, the designed code transitions occur on suc-
cessive integer LSB values. Output coding is straight (natural)
binary with 1 LSB = FS/4096 = 2.5 V/4096 = 0.61 mV. Table
II also shows the ideal input/output transfer function for the
AD7893-2.
Figure 2 shows the analog input section for the AD7893-10,
AD7893-5 and AD7893-3. The analog input range of the
AD7893-10 is ±10 V into an input resistance of typically 33 kΩ.
The analog input range of the AD7893-3 is ±2.5 V into an input
resistance of typically 12 kΩ. The input range on the AD7893-5 is
0 V to +5 V into an input resistance of typically 11 kΩ. This in-
put is benign with no dynamic charging currents, as the resistor
stage is followed by a high input impedance stage of the track/hold
Table II. Ideal Input/Output Code Table for
AD7893-2/AD7893-5
REF IN
Digital Output
Code Transition
Analog Input1
TO ADC
+FSR – 1 LSB2
+FSR – 2 LSB
+FSR – 3 LSB
111 . . . 110 to 111 . . . 111
111 . . . 101 to 111 . . . 110
111 . . . 100 to 111 . . . 101
REFERENCE
CIRCUITRY
R2
R1
TO INTERNAL
COMPARATOR
V
IN
TRACK/
HOLD
R3
AGND + 3 LSB
AGND + 2 LSB
AGND + 1 LSB
000 . . . 010 to 000 . . . 011
000 . . . 001 to 000 . . . 010
000 . . . 000 to 000 . . . 001
AGND
AD7893-10/AD7893-5
NOTES
1FSR is Full-Scale Range and is 5 V for AD7893-5 and 2.5 V for AD7893-2
with REF IN = +2.5 V.
21 LSB = FSR/4096 and is 1.22 mV for AD7893-5 and 0.61 mV for AD7893-2
with REF IN = +2.5 V.
Figure 2. AD7893-10/AD7893-3/AD7893-5 Analog Input
Structure
–6–
REV. E
AD7893
Track/Hold Section
The read operation consists of sixteen serial clock pulses to the
output shift register of the AD7893. After sixteen serial clock
pulses the shift register is reset and the SDATA line is three-
stated. If there are more serial clock pulses after the sixteenth
clock, the shift register will be moved on past its reset state;
however, the shift register will be reset again on the falling edge
of the CONVST signal to ensure that the part returns to a
known state every conversion cycle. As a result, a read operation
from the output register should not straddle across the falling
edge of CONVST as the output shift register will be reset in the
middle of the read operation, and the data read back into the
microprocessor will appear invalid.
The track/hold amplifier on the analog input of the AD7893
allows the ADC to accurately convert an input sine wave of full-
scale amplitude to 12-bit accuracy. The input bandwidth of the
track/hold is greater than the Nyquist rate of the ADC, even
when the ADC is operated at its maximum throughput rate of
117 kHz (i.e., the track/hold can handle input frequencies in
excess of 58 kHz).
The track/hold amplifier acquires an input signal to 12-bit accu-
racy in less than 1.5 µs. The operation of the track/hold is essen-
tially transparent to the user. The track/hold amplifier goes from
its tracking mode to its hold mode at the start of conversion
(i.e., the rising edge of CONVST). The aperture time for the
track/hold (i.e., the delay time between the external CONVST
signal and the track/hold actually going into hold) is typically
15 ns. At the end of conversion (6 µs after the rising edge of
CONVST) the part returns to its tracking mode. The acquisi-
tion time of the track/hold amplifier begins at this point.
The throughput rate of the part can be increased by reading
data during conversion. If the data is read during conversion,
a throughput time of 6 µs (conversion time) plus 1.5 µs is
achieved. This minimum throughput time of 7.5 µs is achieved
with a slight reduction in performance from the AD7893. The
signal to (noise + distortion) number is likely to degrade by ap-
proximately 1.5 dB while the code flicker from the part will also
increase (see AD7893 PERFORMANCE section).
Reference Input
The reference input to the AD7893 is a buffered on-chip with a
maximum reference input current of 1 µA. The part is specified
with a +2.5 V reference input voltage. Errors in the reference
source will result in gain errors in the AD7893’s transfer func-
tion and will add to the specified full-scale errors on the part.
On the AD7893-10 it will also result in an offset error injected
in the attenuator stage. Suitable reference sources for the
AD7893 include the AD780 and AD680 precision +2.5 V
references.
Because the AD7893 is provided in an 8-pin package to mini-
mize board space, the number of pins available for interfacing is
very limited. As a result, no status signal is provided from the
AD7893 to indicate when conversion is complete. In many
applications, this will not be a problem as the data can be read
from the AD7893 during conversion or after conversion; how-
ever, applications that want to achieve optimum performance
from the AD7893 will have to ensure that the data read does not
occur during conversion or during 600 ns prior to the rising
edge of CONVST. This can be achieved in two ways. The first
is to ensure in software that the read operation is not initiated
until 6 µs after the rising edge of CONVST. This will only be
possible if the software knows when the CONVST command is
issued. The second scheme would be to use the CONVST sig-
nal as both the conversion start signal and an interrupt signal.
The simplest way to do this would be to generate a square wave
signal for CONVST with high and low times of 6 µs (see Figure
4). Conversion is initiated on the rising edge of CONVST. The
falling edge of CONVST occurs 6 µs later and can be used as ei-
ther an active low or falling, edge-triggered interrupt signal to
tell the processor to read the data from the AD7893. Provided
that the read operation is completed 600 ns before the rising
edge of CONVST, the AD7893 will operate to specification.
Timing and Control Section
Figure 3 shows the timing and control sequence required to ob-
tain optimum performance from the AD7893. In the sequence
shown, conversion is initiated on the rising edge of CONVST,
and new data from this conversion is available in the output reg-
ister of the AD7893 6 µs later. Once the read operation has
taken place, a further 600 ns should be allowed before the next
rising edge of CONVST to optimize the settling of the track/
hold amplifier before the next conversion is initiated. With the
serial clock frequency at its maximum of 8.33 MHz, the achiev-
able throughput rate for the part is 6 µs (conversion time) plus
1.92 µs (read time) plus 0.6 µs (acquisition time). This results in
a minimum throughput time of 8.52 µs (equivalent to a through-
put rate of 117 kHz).
t1
CONVST
600ns MIN
SCLK
tCONVERT
CONVERSION IS INITIATED
AND TRACK/HOLD GOES
INTO HOLD
CONVERSION ENDS
6µs LATER
SERIAL READ
OPERATION
READ OPERATION
SHOULD END 600ns
PRIOR TO NEXT
OUTPUT SERIAL
SHIFT REGISTER IS
RESET
RISING EDGE OF
CONVST
Figure 3. Timing Sequence for Optimum Performance from the AD7893
REV. E
–7–
AD7893
CONVST
600ns MIN
SCLK
tCONVERT
CONVERSION IS INITIATED
AND TRACK/HOLD GOES
INTO HOLD
µP INT SERVICE
OR POLLING
ROUTINE
SERIAL READ
OPERATION
READ OPERATION
SHOULD END 600ns
PRIOR TO NEXT
CONVST INDICATES
TO µP THAT
CONVERSION IS
COMPLETE
RISING EDGE OF
CONVST
Figure 4. CONVST Used as Status Signal
This scheme limits the throughput rate to 12 µs minimum; how-
ever, depending on the response time of the microprocessor to
the interrupt signal and the time taken by the processor to read
the data, this may be the fastest the system could have operated.
In any case, the CONVST signal does not have to have a 50:50
duty cycle. This can be tailored to optimize the throughput rate
of the part for a given system.
clock, the AD7893 will start over again with outputting data
from its output register, and the data bus will no longer be
three-stated even when the clock stops. Provided that the serial
clock has stopped before the next falling edge of CONVST, the
AD7893 will continue to operate correctly with the output shift
register being reset on the falling edge of CONVST; however,
the SCLK line must be low when CONVST goes low in order
to reset the output shift register correctly.
Alternatively, the CONVST signal can be used as a normal narrow
pulse width. The rising edge of CONVST can be used as an active
high or rising edge-triggered interrupt. A software delay of 6 µs can
then be implemented before data is read from the part.
The serial clock input does not have to be continuous during the
serial read operation. The sixteen bits of data (four leading zeros
and 12 bit conversion result) can be read from the AD7893 in a
number of bytes; however, the SCLR input must remain low be-
tween the two bytes.
Serial Interface
The serial interface to the AD7893 consists of just two wires, a
serial clock input (SCLK) and the serial data output (SDATA).
This allows for an easy to use interface to most microcontrollers,
DSP processors and shift registers.
Normally, the output register is updated at the end of conver-
sion. If a serial read from the output register is in progress when
conversion is complete; however, the updating of the output
register is deferred. In this case, the output register is updated
when the serial read is completed. If the serial read has not been
completed before the next falling edge of CONVST, the output
register will be updated on the falling edge of CONVST, and
the output shift register count is reset. In applications where the
data read has been started and not completed before the falling
edge of CONVST, the user must provide a CONVST pulse
width of greater than 1.5 µs to ensure correct setup of the AD7893
before the next conversion is initiated. In applications where the
output update takes place either at the end of conversion or at
the end of a serial read that is completed 1.5 µs before the rising
edge of CONVST, the normal pulse width of 50 ns minimum
applies to CONVST.
Figure 5 shows the timing diagram for the read operation to the
AD7893. The serial clock input (SCLK) provides the clock
source for the serial interface. Serial data is clocked out from the
SDATA line on the rising edge of this clock and is valid on the
falling edge of SCLK. Sixteen clock pulses must be provided to
the part to access to full conversion result. The AD7893 pro-
vides four leading zeros followed by the 12-bit conversion result
starting with the MSB (DB11). The last data bit to be clocked
out on the final rising clock edge is the LSB (DB0). On the six-
teenth falling edge of SCLK, the SDATA line is disabled (three-
stated). After this last bit has been clocked out, the SCLK input
should return low and remain low until the next serial data read
operation. If there are extra clock pulses after the sixteenth
t2
SCLK (I)
t3
t5
DB0
t4
THREE-STATE
THREE-STATE
SDATA (O)
DB11
DB10
FOUR LEADING ZEROS
Figure 5. Data Read Operation
–8–
REV. E
AD7893
The AD7893 counts the serial clock edges to know which bit
from the output register should be placed on the SDATA out-
put. To ensure that the part does not lose synchronization, the
serial clock counter is reset on the falling edge of the CONVST
input, provided the SCLR line is low. The user should ensure
that a falling edge on the CONVST input does not occur while
a serial data read operation is in progress.
The serial clock rate from the 8XC51 is limited to significantly
less than the allowable input serial clock frequency with which
the AD7893 can operate. As a result, the time to read data from
the part will actually be longer than the conversion time of the
part. This means that the AD7893 cannot run at its maximum
throughput rate when used with the 8XC51.
AD7893-68HC11 Interface
An interface circuit between the AD7893 and the 68HC11
microcontroller is shown in Figure 7. For the interface shown,
the 68HC11 SPI port is used, and the 68HC11 is configured in
its single-chip mode. The 68HC11 is configured in the master
mode with its CPOL bit set to a logic zero and its CPHA bit set
to a logic one. As with the previous interface, the diagram shows
the simplest form of the interface where the AD7893 is the only
part connected to the serial port of the 68HC11 and, therefore,
no decoding of the serial read operations is required. It also
makes no provisions for monitoring when conversion is com-
plete on the AD7893.
MICROPROCESSOR/MICROCONTROLLER INTERFACE
The AD7893 provides a two-wire serial interface that can be
used for connection to the serial ports of DSP processors and
microcontrollers. Figures 6 through 9 show the AD7893 inter-
faced to a number of different microcontrollers and DSP pro-
cessors. The AD7893 accepts an external serial clock and, as a
result, in all interfaces shown here, the processor/controller is
configured as the master, providing the serial clock with the
AD7893 configured as the slave in the system.
AD7893-8051 Interface
Figure 6 shows an interface between the AD7893 and the
8XC51 microcontroller. The 8XC51 is configured for its Mode
0 serial interface mode. The diagram shows the simplest form of
the interface where the AD7893 is the only part connected to
the serial port of the 8XC51 and, therefore, no decoding of the
serial read operations is required. It also makes no provisions for
monitoring when conversion is complete on the AD7893.
Once again, either of these two tasks can readily be accom-
plished with minor modifications to the interface. To chip select
the AD7893 in systems where more than one device is con-
nected to the 68HC11’s serial port, a port bit, configured as an
output from one of the 68HC11’s parallel ports, can be used to
gate on or off the serial clock to the AD7893. A simple AND
function on this port bit and the serial clock from the 68HC11
will provide this function. The port bit should be high to select
the AD7893 and low when it is not selected.
Either of these two tasks can readily be accomplished with minor
modifications to the interface. To chip select the AD7893 in
systems where more than one device is connected to the 8XC51’s
serial port, a port bit configured as an output from one of the
8XC51’s parallel ports can be used to gate on or off the serial
clock to the AD7893. A simple AND function on this port bit
and the serial clock from the 8XC51 will provide this function.
The port bit should be high to select the AD7893 and low when
it is not selected.
To monitor the conversion time on the AD7893, a scheme such
as outlined in the previous interface with CONVST can be
used. This can be implemented in two ways. One is to connect
the CONVST line to another parallel port bit that is configured
as an input. This port bit can then be polled to determine when
conversion is complete. An alternative is to use an interrupt
driven system, in which case the CONVST line should be con-
nected to the IRQ input of the 68HC11.
To monitor the conversion time on the AD7893, a scheme such
as previously outlined with CONVST can be used. This can be
implemented in two ways. One is to connect the CONVST line
to another parallel port bit that is configured as an input. This
port bit can then be polled to determine when conversion is
complete. An alternative is to use an interrupt driven system, in
which case the CONVST line should be connected to the INT1
input of the 8XC51.
The serial clock rate from the 68HC11 is limited to significantly
less than the allowable input serial clock frequency with which
the AD7893 can operate. As a result, the time to read data from
the part will actually be longer than the conversion time of the
part. This means that the AD7893 cannot run at its maximum
throughput rate when used with the 68HC11.
68HC11
AD7893
8XC51
AD7893
SCLK
SCK
P3.0
P3.1
SDATA
SCLK
SDATA
MISO
Figure 7. AD7893 to 68HC11 Interface
Figure 6. AD7893 to 8XC51 Interface
REV. E
–9–
AD7893
AD7893–ADSP-2105 Interface
An interface circuit between the AD7893 and the ADSP-2105
DSP processor is shown in Figure 8. In the interface shown, the
RFS1 output from the ADSP-2105’s SPORT1 serial port is
used to gate the serial clock (SCLK1) of the ADSP-2105 before
it is applied to the SCLK input of the AD7893. The RFS1 out-
put is configured for active high operation. The interface
ensures a noncontinuous clock for the AD7893’s serial clock
input with only sixteen serial clock pulses provided, and the
serial clock line of the AD7893 remaining low between data
transfers. The SDATA line from the AD7893 is connected to
the DR1 line of the ADSP-2105’s serial port.
DSP56000
AD7893
SDATA
SRD
SC0
SCLK
Figure 9. AD7893 to DSP56000 Interface
AD7893 PERFORMANCE
Linearity
ADSP-2105
The linearity of the AD7893 is determined by the on-chip 12-bit
D/A converter. This is a segmented DAC that is laser trimmed
for 12-bit integral linearity and differential linearity. Typical
relative numbers for the part are ±1/4 LSB, while the typical
DNL errors are ±1/2 LSB.
AD7893
RFS1
SCLK
SCLK1
DR1
SDATA
Noise
In an A/D converter, noise exhibits itself as code uncertainty in
dc applications and as the noise floor (in an FFT, for example)
in ac applications. In a sampling A/D converter like the AD7893,
all information about the analog input appears in the baseband
from dc to 1/2 the sampling frequency. The input bandwidth of
the track/hold exceeds the Nyquist bandwidth; therefore, an
antialiasing filter should be used to remove unwanted signals
above fS/2 in the input signal in applications where such signals
exist.
Figure 8. AD7893 to ADSP-2105 Interface
The timing relationship between the SCLK1 and RFS1 outputs
of the ADSP-2105 are such that the delay between the rising
edge of the SCLK1 and the rising edge of an active high RFS1
is up to 25 ns. There is also a requirement that data must be set
up 10 ns prior to the falling edge of the SCLK1 to be read cor-
rectly by the ADSP-2105. The data access time for the AD7893
is 50 ns from the rising edge of its SCLK input. Assuming a
10 ns propagation delay through the external AND gate, the
high time of the SCLK1 output of the ADSP-2105 must be
≥ (50 + 25 + 10 + 10) ns, i.e., ≥ 95 ns. This means that the
serial clock frequency with which the interface of Figure 13 can
work with is limited to 5.26 MHz.
Figure 10 shows a histogram plot for 8192 conversions of a dc
input using the AD7893. The analog input was set at the center
of a code transition. The timing and control sequence used was
per Figure 3 where the optimum performance of the ADC was
achieved. It can be seen that almost all the codes appear in the
one output bin, indicating very good noise performance from
the ADC. The rms noise performance for the AD7893-2 for the
above plot was 87 µV. Since the analog input range, and hence
LSB size, on the AD7893-10 is eight times what it is for the
AD7893-2, the same output code distribution results in an out-
put rms noise of 700 µV for the AD7893-10.
An alternative scheme is to configure the ADSP-2105 to accept
an external serial clock. In this case, an external noncontinuous
serial clock that drives the serial clock inputs of both the ADSP-
2105 and the AD7893 is provided. In this scheme, the serial
clock frequency is limited to 5 MHz by the ADSP-2105.
To monitor the conversion time on the AD7893, a scheme such
as outlined in previous interfaces with CONVST can be used.
This can be implemented by connecting the CONVST line
directly to the IRQ2 input of the ADSP-2105.
9000
SAMPLING FREQUENCY = 102.4kHz
T
= +25°C
A
8000
7000
AD7893–DSP56000 Interface
6000
5000
4000
Figure 9 shows an interface circuit between the AD7893 and the
DSP56000 DSP processor. The DSP5600 is configured for nor-
mal mode asynchronous operation with gated clock. It is also set
up for a 16-bit word with the gated serial clock being generated
by the DSP56000 and appears on the SC0 pin. The SC0 pin
should be configured as an output by setting bit SCD0 to 1. In
this mode, the DSP56000 provides sixteen serial clock pulses to
the AD7893 in a serial read operation. The DSP56000 assumes
valid data on the first falling edge of SCK, so the interface is
simply two-wire as shown in Figure 9.
3000
2000
1000
0
(X–4) (X–3) (X–2) (X–1)
X
(X+1) (X+2) (X+3) (X+4)
CODE
To monitor the conversion time on the AD7893, a scheme such
as outlined in previous interface examples with CONVST can
be used. This can be implemented by connecting the CONVST
line directly to the IRQA input of the DSP56000.
Figure 10. Histogram of 8192 Conversions of a DC Input
–10–
REV. E
AD7893
The same data is presented in Figure 11 as in Figure 10 except
that, in this case, the output data read for the device occurs dur-
ing conversion. This has the effect of injecting noise onto the die
while bit decisions are being made; this increases the noise gen-
erated by the AD7893. The histogram plot for 8192 conversions
of the same dc input now shows a larger spread of codes with
the rms noise for the AD7893-2 increasing to 210 µV. This ef-
fect will vary depending on where the serial clock edges appear
with respect to the bit trials of the conversion process. It is pos-
sible to achieve the same level of performance when reading
during conversion as when reading after conversion, depending
on the relationship of the serial dock edges to the bit trial points.
Effective Number of Bits
The formula for signal to (noise + distortion) ratio (see Termi-
nology section) is related to the resolution or number of bits in
the converter. Rewriting the formula gives a measure of perfor-
mance expressed in effective number of bits (N):
N = (SNR – 1.76) / 6.02
where SNR is Signal to (Noise + Distortion) Ratio.
The effective number of bits for a device can be calculated from
its measured signal to (noise + distortion) ratio. Figure 13 shows
a typical plot of effective number of bits versus frequency for the
AD7893-2 from dc to fSAMPLING/2. The sampling frequency is
102.4 kHz. The plot shows that the AD7893 converts an input
sine wave of 51.2 kHz to an effective numbers of bits of 11,
which equates to a signal to (noise + distortion) level of 68 dB.
7500
7000
SAMPLING
FREQUENCY = 102.4kHz
6500
6000
5500
5000
4500
4000
3500
3000
2500
2000
1500
T
= +25°C
A
12.0
11.5
11.0
10.5
10.0
1000
500
0
(X–4) (X–3) (X–2) (X–1)
X
(X+1) (X+2) (X+3) (X+4)
CODE
Figure 11. Histogram of 8192 Conversions with Read Dur-
ing Conversion
0
25.6
51.2
INPUT FREQUENCY – kHz
Dynamic Performance
With a combined conversion and acquisition time of 7.5 µs, the
AD7893 is ideal for wide bandwidth signal processing applica-
tions. These applications require information on the ADC’s
effect on the spectral content of the input signal. Signal to (noise
+ distortion) ratio, total harmonic distortion, peak harmonic or
spurious noise, and intermodulation distortion are all specified.
Figure 12 shows a typical FFT plot of a 10 kHz, 0 V to +2.5 V
input after being digitized by the AD7893-2, operating at a
102.4 kHz sampling rate. The signal to (noise + distortion)
ratio is 71.5 dB, and the total harmonic distortion is –83 dB.
Figure 13. Effective Number of Bits vs. Frequency
0
SAMPLE RATE = 102.4kHz
INPUT FREQUENCY = 10kHz
SNR = 71.5dB
T
= +25°C
–30
–60
A
–80
–120
–180
0
25.6
51.2
FREQUENCY – kHz
SNR IS SIGNAL TO (NOISE AND DISTORTION) RATIO
Figure 12. AD7893 FFT Plot
REV. E
–11–
AD7893
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
Plastic DIP (N-8)
8
5
0.280 (7.11)
0.240 (6.10)
PIN 1
1
4
0.325 (8.25)
0.300 (7.62)
0.430 (10.92)
0.348 (8.84)
0.060 (1.52)
0.015 (0.38)
0.195 (4.95)
0.115 (2.93)
0.210
(5.33)
MAX
0.130
(3.30)
MIN
0.015 (0.381)
0.008 (0.204)
0.160 (4.06)
0.115 (2.93)
SEATING
PLANE
0.100
(2.54)
0.022 (0.558)
0.014 (0.356)
0.070 (1.77)
0.045 (1.15)
BSC
Cerdip (Q-8)
0.005 (0.13) MIN
0.055 (1.4) MAX
8
5
0.310 (7.87)
0.220 (5.59)
PIN 1
1
4
0.320 (8.13)
0.290 (7.37)
0.405 (10.29) MAX
0.060 (1.52)
0.015 (0.38)
0.200
(5.08)
MAX
0.150
(3.81)
MIN
0.015 (0.38)
0.008 (0.20)
0.200 (5.08)
0.125 (3.18)
15
°
0°
0.023 (0.58) 0.100 0.070 (1.78)
SEATING
PLANE
(2.54)
BSC
0.014 (0.36)
0.030 (0.76)
SOIC (SO-8)
8
5
0.1574 (4.00)
0.1497 (3.80)
PIN 1
0.2440 (6.20)
0.2284 (5.80)
4
1
0.1968 (5.00)
0.1890 (4.80)
0.0196 (0.50)
0.0099 (0.25)
x 45
°
0.0688 (1.75)
0.0532 (1.35)
0.0098 (0.25)
0.0040 (0.10)
8
0
°
°
0.0500 (1.27)
0.0160 (0.41)
0.0500
(1.27)
BSC
0.0192 (0.49)
0.0138 (0.35)
0.0098 (0.25)
0.0075 (0.19)
–12–
REV. E
1 of 2
Package/Price Information
True Bipolar Input, Single Supply, 12-Bit, Serial 6 µs ADC in 8-Pin Package
Price*
(1000-
4999)
Package
Description
Pin
Count
Temperature
Range
Model
Status
CERDIP GLASS
SEAL
5962-9475501MPA
5962-9475502MPA
PRODUCTION
PRODUCTION
8
8
MILITARY
MILITARY
$55.25
$55.25
CERDIP GLASS
SEAL
AD7893ACHIPS-10
AD7893ACHIPS-2
AD7893ACHIPS-5
AD7893AN-10
PRODUCTION CHIPS/DIE SALES
PRODUCTION CHIPS/DIE SALES
PRODUCTION CHIPS/DIE SALES
PRODUCTION PLASTIC/EPOXY DIP
PRODUCTION PLASTIC/EPOXY DIP
PRODUCTION PLASTIC/EPOXY DIP
-
-
COMMERCIAL $7.20
COMMERCIAL $7.20
COMMERCIAL $7.20
COMMERCIAL $9.00
COMMERCIAL $9.00
COMMERCIAL $9.00
-
8
8
8
AD7893AN-2
AD7893AN-5
STD S.O. PKG
PRODUCTION
AD7893AR-10
8
8
8
8
8
8
8
8
8
8
8
8
COMMERCIAL $9.00
COMMERCIAL $9.00
COMMERCIAL $9.00
COMMERCIAL $9.00
COMMERCIAL $9.00
COMMERCIAL $9.00
COMMERCIAL $9.00
COMMERCIAL $9.00
COMMERCIAL $9.00
COMMERCIAL $9.00
COMMERCIAL $9.00
COMMERCIAL $9.00
(SOIC)
STD S.O. PKG
PRODUCTION
AD7893AR-10REEL
(SOIC)
AD7893AR-
10REEL7
STD S.O. PKG
PRODUCTION
(SOIC)
STD S.O. PKG
PRODUCTION
AD7893AR-2
(SOIC)
STD S.O. PKG
PRODUCTION
AD7893AR-2REEL
AD7893AR-2REEL7
AD7893AR-3
(SOIC)
STD S.O. PKG
PRODUCTION
(SOIC)
STD S.O. PKG
PRODUCTION
(SOIC)
STD S.O. PKG
PRODUCTION
AD7893AR-3REEL
AD7893AR-3REEL7
AD7893AR-5
(SOIC)
STD S.O. PKG
PRODUCTION
(SOIC)
STD S.O. PKG
PRODUCTION
(SOIC)
STD S.O. PKG
PRODUCTION
AD7893AR-5REEL
AD7893AR-5REEL7
(SOIC)
STD S.O. PKG
PRODUCTION
(SOIC)
2 of 2
AD7893BN-10
PRODUCTION PLASTIC/EPOXY DIP
PRODUCTION PLASTIC/EPOXY DIP
PRODUCTION PLASTIC/EPOXY DIP
8
8
8
COMMERCIAL $11.65
COMMERCIAL $11.66
COMMERCIAL $11.66
AD7893BN-2
AD7893BN-5
STD S.O. PKG
PRODUCTION
AD7893BR-10
8
8
8
8
8
8
8
8
8
8
8
COMMERCIAL $11.66
COMMERCIAL $11.66
COMMERCIAL $11.66
COMMERCIAL $11.66
COMMERCIAL $11.66
COMMERCIAL $11.66
COMMERCIAL $11.66
COMMERCIAL $11.66
COMMERCIAL $42.08
COMMERCIAL $42.08
COMMERCIAL $42.08
(SOIC)
STD S.O. PKG
PRODUCTION
AD7893BR-10REEL
AD7893BR-2
(SOIC)
STD S.O. PKG
PRODUCTION
(SOIC)
STD S.O. PKG
PRODUCTION
AD7893BR-2REEL
AD7893BR-2REEL7
AD7893BR-5
(SOIC)
STD S.O. PKG
PRODUCTION
(SOIC)
STD S.O. PKG
PRODUCTION
(SOIC)
STD S.O. PKG
PRODUCTION
AD7893BR-5REEL
AD7893BR-5REEL7
AD7893SQ-10
(SOIC)
STD S.O. PKG
PRODUCTION
(SOIC)
CERDIP GLASS
PRODUCTION
SEAL
CERDIP GLASS
AD7893SQ-2
PRODUCTION
SEAL
CERDIP GLASS
AD7893SQ-5
PRODUCTION
SEAL
* This price is provided for budgetary purposes as recommended list price in U.S. Dollars per unit in
the stated volume. Pricing displayed for Evaluation Boards and Kits is based on 1-piece pricing. View
Pricing and Availability for further information.
相关型号：
AD7893AR-2REEL7
True Bipolar Input, Single Supply, 12-Bit, Serial 6 µs ADC in 8-Pin Package
ADI
AD7893AR-3REEL7
IC 1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8, SOIC-8, Analog to Digital Converter
ADI
©2020 ICPDF网 联系我们和版权申明