AD8145WYCPZ-R72 [ADI]
High Speed, Triple Differential Receiver with Comparators; 高速,三路差分接收器与比较型号: | AD8145WYCPZ-R72 |
厂家: | ADI |
描述: | High Speed, Triple Differential Receiver with Comparators |
文件: | 总24页 (文件大小:464K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
High Speed, Triple Differential Receiver
with Comparators
AD8145
FUNCTIONAL BLOCK DIAGRAM
FEATURES
High speed: 500 MHz, 2000 V/μs @ G = 1, VOUT = 2 V p-p
0.1 dB flatness out to 75 MHz
32
31
30
29
28
–
27
26
25
High CMRR: 69 dB @ 10 MHz
C
High differential input impedance: 1 MΩ
Wide input common-mode range: 3.5 V ( 5 V supplies)
On-chip, gain setting resistors can be configured for gain of 1 or 2
Fast settling: 15 ns to 0.1% @ 2 V p-p
Low input referred noise: 13 nV/√Hz
Disable feature
1
2
3
4
5
6
7
8
R
R
24
23
22
21
20
19
18
17
GND
REF_G
GAIN_G
IN+_G
GND
–
OUT_B
OUT_G
OUT_R
+
C
R
–
R
+
–
Small packaging: 32-lead, 5 mm × 5 mm LFCSP
AEC-Q10 qualified (AD8145W)
IN–_G
V
S+
AD8145
REF_R
GAIN_R
GND
+
–
COMPB_IN+
COMPB_IN–
GND
C
R
B
APPLICATIONS
A
R
RGB video receivers
–
YPbPr video receivers
9
10
11
12
13
14
15
16
Keyboard, video, mouse (KVM)
Unshielded twisted pair (UTP) receivers
Automotive driver assistance (AD8145W)
Automotive Infotainment (AD8145W)
Figure 1.
GENERAL DESCRIPTION
The AD8145 is a triple, low cost, differential-to-single-ended
receiver specifically designed for receiving red-green-blue (RGB)
video signals over twisted pair cable or differential printed circuit
board (PCB) traces. It can also be used to receive any type of
analog signal or high speed data transmission. Two auxiliary
comparators with hysteresis are provided that can be used to
decode video sync signals, which are encoded on the received
common-mode voltages, to receive digital signals or as general-
purpose comparators. The AD8145 can be used in conjunction
with the AD8133 or AD8134 triple differential drivers to provide a
complete low cost solution for RGB over Category 5 UTP cable
applications, including KVM.
The AD8145 can be configured for a differential-to-single-ended
gain of 1 or 2 by connecting the GAIN_x pin of each channel to
its respective output (G = 1) or connecting it to a reference voltage
(G = 2), which is normally grounded.
A REF_x input is provided on each channel that allows designers to
level shift the output signals.
The AD8145W is the automotive grade version that is qualified
per the AEC-Q100 for use in automotive applications. See the
Automotive Products section for more details.
The AD8145 is available in a 5 mm × 5 mm, 32-lead LFCSP and
is rated to work over the extended industrial temperature range
of −40°C to +105°C.
The excellent common-mode rejection (69 dB @ 10 MHz) of
the AD8145 allows for the use of low cost, unshielded twisted
pair cables in noisy environments.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2006–2010 Analog Devices, Inc. All rights reserved.
AD8145
TABLE OF CONTENTS
Features .............................................................................................. 1
Overview ..................................................................................... 15
Basic Closed-Loop Gain Configurations ................................ 15
Terminating the Input................................................................ 16
Input Clamping........................................................................... 17
PCB Layout Considerations...................................................... 18
Driving a Capacitive Load......................................................... 19
Power-Down ............................................................................... 19
Automotive Products................................................................. 19
Comparators ............................................................................... 19
Sync Pulse Extraction Using Comparators............................. 20
Outline Dimensions....................................................................... 21
Ordering Guide .......................................................................... 21
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description......................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Absolute Maximum Ratings............................................................ 7
Thermal Resistance ...................................................................... 7
Maximum Power Dissipation ..................................................... 7
ESD Caution.................................................................................. 7
Pin Configuration and Function Description .............................. 8
Typical Performance Characteristics ............................................. 9
Theory of Operation ...................................................................... 14
Applications Information .............................................................. 15
REVISION HISTORY
1/10—Rev. 0 to Rev. A
Changes to Features Section, Applications Section, and General
Description Section.......................................................................... 1
Changes to Table 1............................................................................ 3
Changes to Table 2............................................................................ 5
Added Automotive Products Section .......................................... 19
Added Exposed Paddle Notation to Outline Dimensions ........ 21
Changes to Ordering Guide .......................................................... 21
10/06—Revision 0: Initial Version
Rev. A | Page 2 of 24
AD8145
SPECIFICATIONS
TA = 25°C, VS = 5 V, REF_x = 0 V, RL = 150 Ω, CL = 2 pF, G = 1, TMIN to TMAX = −40°C to +105°C, unless otherwise noted.
Table 1.
Parameter
Conditions
Min
Typ
Max
Unit
DYNAMIC PERFORMANCE
−3 dB Bandwidth
VOUT = 0.2 V p-p
VOUT = 2 V p-p
530
500
200
200
75
100
2100
2100
15
MHz
MHz
MHz
MHz
MHz
MHz
V/μs
V/μs
ns
VOUT = 0.2 V p-p, G = 2
VOUT = 2 V p-p, G = 2
VOUT = 2 V p-p
VOUT = 2 V p-p, G = 2
VOUT = 2 V p-p
Bandwidth for 0.1 dB Flatness
Slew Rate
VOUT = 2 V p-p, G = 2
VOUT = 2 V p-p, 0.1%
Settling Time
Output Overdrive Recovery
NOISE/DISTORTION
Second Harmonic
Third Harmonic
Crosstalk
Input Voltage Noise (RTI)
Differential Gain Error
Differential Phase Error
INPUT CHARACTERISTICS
Common-Mode Rejection
20
ns
VOUT = 2 V p-p, 1 MHz
VOUT = 2 V p-p, 1 MHz
VOUT = 2 V p-p, 10 MHz
f ≥ 10 kHz
NTSC, 200 IRE, RL ≥ 150 Ω
NTSC, 200 IRE, RL ≥ 150 Ω
−67
−88
−62
13
0.25
0.1
dBc
dBc
dB
nV/√Hz
%
Degrees
DC, VCM = −2 V to +2 V
AD8145W only, TMIN to TMAX
VCM = 1 V p-p, f = 10 MHz
VCM = 1 V p-p, f = 100 MHz
V+IN − V−IN = 0 V
81
78
90
dB
dB
dB
dB
V
69
41
3.5
2.5
1
1.3
1
2
Common-Mode Voltage Range
Differential Operating Range
Resistance
V
Differential
Common mode
Differential
MΩ
MΩ
pF
pF
Capacitance
Common mode
DC PERFORMANCE
Closed-Loop Gain
DC, G = 2
AD8145W only, TMIN to TMAX
G = 2
AD8145W only, TMIN to TMAX
TMIN to TMAX
1.955
1.930
−17.5
−25
1.985
+7.0
2.020
2.030
+1.0
V/V
V/V
mV
mV
μV/°C
μA
μA
nA/°C
nA
Output Offset Voltage
+8.0
Output Offset Voltage Drift
Input Bias Current (+IN, −IN)
−18
−3.4
−6
−7
−0.9
−0.5
AD8145W only, TMIN to TMAX
TMIN to TMAX (+IN, −IN)
Input Bias Current Drift
Input Offset Current
25
−65
−400
−650
+300
+650
AD8145W only, TMIN to TMAX
nA
OUTPUT PERFORMANCE
Voltage Swing
−3.64
−3.45
+3.55
+3.35
V
V
mA
mA
AD8145W only, TMIN to TMAX
Short to GND, source/sink
Output Current
Short-Circuit Current
50
+195/−230
Rev. A | Page 3 of 24
AD8145
Parameter
Conditions
Min
Typ
Max
Unit
COMPARATOR PERFORMANCE
VOH
RL = 1 kΩ
AD8145W only, TMIN to TMAX
RL = 1 kΩ
3.205
2.950
3.310
0.390
V
V
V
V
VOL
0.420
0.440
AD8145W only, TMIN to TMAX
Input Offset Voltage
Hysteresis Width
Input Bias Current
Propagation Delay, tPLH
Propagation Delay, tPHL
Rise Time
2.5
18
1.5
6
6
6
mV
mV
μA
ns
ns
ns
ns
10% to 90%
10% to 90%
Fall Time
2
POWER-DOWN PERFORMANCE
Power-Down VIH
Power-Down VIL
Power-Down IIH
Power-Down IIL
VS+ − 1.65
VS+ − 2.65
0.5
−250
1
V
V
μA
μA
μs
Power-Down Assert Time
POWER SUPPLY
Operating Range
4.5
11
V
Quiescent Current, Positive Supply
48.5
16
57.5
70
19.5
25
mA
mA
mA
mA
mA
mA
mA
mA
dB
AD8145W only, TMIN to TMAX
Disabled
AD8145W only, TMIN to TMAX
Quiescent Current, Negative Supply
−52
−65
−13.9
−20
−43.5
−11
−79
−68
AD8145W only, TMIN to TMAX
Disabled
AD8145W only, TMIN to TMAX
DC
AD8145W only, TMIN to TMAX
DC
AD8145W only, TMIN to TMAX
PSRR, Positive Supply
PSRR, Negative Supply
−70
−66
−57
−54
dB
dB
dB
Rev. A | Page 4 of 24
AD8145
TA = 25°C, VS = 2.5 V, REF_x = 0 V, RL = 1 kΩ, CL = 2 pF, G = 1, TMIN to TMAX = −40°C to +105°C, unless otherwise noted.
Table 2.
Parameter
Conditions
Min
Typ
Max
Unit
DYNAMIC PERFORMANCE
−3 dB Bandwidth
VOUT = 0.2 V p-p
VOUT = 2 V p-p
450
425
180
180
53
100
2000
2000
16
MHz
MHz
MHz
MHz
MHz
MHz
V/μs
V/μs
ns
VOUT = 0.2 V p-p, G = 2, RL = 150 Ω
VOUT = 2 V p-p, G = 2, RL = 150 Ω
VOUT = 2 V p-p
VOUT = 2 V p-p, G = 2, RL = 150 Ω
VOUT = 2 V p-p
Bandwidth for 0.1 dB Flatness
Slew Rate
VOUT = 2 V p-p, G = 2, RL = 150 Ω
VOUT = 2 V p-p, 0.1%
Settling Time
Output Overdrive Recovery
NOISE/DISTORTION
Second Harmonic
Third Harmonic
Crosstalk
Input Voltage Noise (RTI)
INPUT CHARACTERISTICS
Common-Mode Rejection
10
ns
VOUT = 1 V p-p, 1 MHz
VOUT = 1 V p-p, 1 MHz
VOUT = 1 V p-p, 10 MHz
f ≥ 10 kHz
−71
−76
−62
13
dBc
dBc
dB
nV/√Hz
DC, VCM = −1 V to +1 V
AD8145W only, TMIN to TMAX
VCM = 1 V p-p, f = 10 MHz
VCM = 1 V p-p, f = 100 MHz
V+IN − V−IN = 0 V
78
75
86
dB
dB
dB
dB
V
72
43
1.25
1.6
1
1.3
1
2
Common-Mode Voltage Range
Differential Operating Range
Resistance
V
Differential
Common mode
Differential
MΩ
MΩ
pF
pF
Capacitance
Common mode
DC PERFORMANCE
Closed-Loop Gain
DC, G = 2
AD8145W only, TMIN to TMAX
G = 2
AD8145W only, TMIN to TMAX
TMIN to TMAX
1.960
1.930
−13.5
−18
1.985
−4.5
2.016
2.030
+2
V/V
V/V
mV
mV
μV/°C
μA
μA
nA/°C
nA
Output Offset Voltage
+8
Output Offset Voltage Drift
Input Bias Current (+IN, −IN)
−18
−3.5
−6
−7
−0.9
−0.5
AD8145W only, TMIN to TMAX
TMIN to TMAX (+IN, −IN)
Input Bias Current Drift
Input Offset Current
25
−60
−400
−650
+300
+650
AD8145W only, TMIN to TMAX
nA
OUTPUT PERFORMANCE
Voltage Swing
RL = 150 Ω
AD8145W only, TMIN to TMAX
−1.35
−1.20
+1.3
+1.15
V
V
Output Current
25
mA
mA
Short-Circuit Current
POWER-DOWN PERFORMANCE
Power-Down VIH
Power-Down VIL
Power-Down IIH
Short to GND, source/sink
+100/−100
VS+ − 1.5
VS+ − 2.5
0.25
50
1
V
V
μA
μA
μs
Power-Down IIL
Power-Down Assert Time
Rev. A | Page 5 of 24
AD8145
Parameter
Conditions
Min
Typ
Max
Unit
POWER SUPPLY
Operating Range
Quiescent Current, Positive Supply
4.5
11
47
57
16
21
V
40
mA
mA
mA
mA
mA
mA
mA
mA
dB
AD8145W only, TMIN to TMAX
Disabled
AD8145W only, TMIN to TMAX
13.5
−36
−10
−83
−67
Quiescent Current, Negative Supply
−43.5
−54
−12.5
−17
AD8145W only, TMIN to TMAX
Disabled
AD8145W only, TMIN to TMAX
DC
AD8145W only, TMIN to TMAX
DC
AD8145W only, TMIN to TMAX
PSRR, Positive Supply
PSRR, Negative Supply
−73
−68
−62
−59
dB
dB
dB
Rev. A | Page 6 of 24
AD8145
ABSOLUTE MAXIMUM RATINGS
MAXIMUM POWER DISSIPATION
Table 3.
The maximum safe power dissipation in the AD8145 package is
limited by the associated rise in junction temperature (TJ) on
the die. At approximately 150°C, which is the glass transition
temperature, the plastic changes its properties. Even temporarily
exceeding this temperature limit can change the stresses that the
package exerts on the die, permanently shifting the parametric
performance of the AD8145. Exceeding a junction temperature
of 150°C for an extended period can result in changes in the
silicon devices, potentially causing failure.
Parameter
Rating
Supply Voltage
Power Dissipation
Storage Temperature Range
Operating Temperature Range
Lead Temperature (Soldering, 10 sec)
Junction Temperature
12 V
See Figure 2
−65°C to +125°C
−40°C to +105°C
300°C
150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
The power dissipated in the package (PD) is the sum of the
quiescent power dissipation and the power dissipated in the
package due to the load drive for all outputs. The quiescent
power is the voltage between the supply pins (VS) times the
quiescent current (IS). The power dissipated due to the load
drive depends on the particular application. For each output, the
power due to load drive is calculated by multiplying the load
current by the associated voltage drop across the device. The
power dissipated due to all of the loads is equal to the sum of
the power dissipation due to each individual load. RMS voltages
and currents must be used in these calculations.
THERMAL RESISTANCE
θJA is specified for the worst-case conditions, that is, θJA is
specified for a device soldered in the circuit board with its
exposed paddle soldered to a pad on the PCB surface, which is
thermally connected to a copper plane.
Airflow increases heat dissipation, effectively reducing θJA. In
addition, more metal directly in contact with the package leads
from metal traces, through-holes, ground, and power planes
reduces the θJA. The exposed paddle on the underside of the
package must be soldered to a pad on the PCB surface, which is
thermally connected to a copper plane to achieve the specified θJA.
Table 4. Thermal Resistance
Package Type
θJA
θJC
Unit
5 mm × 5 mm, 32-Lead LFCSP
47
8.5
°C/W
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
Figure 2 shows the maximum safe power dissipation in the
package vs. the ambient temperature for the 32-lead LFCSP
(47°C/W) on a JEDEC standard 4-layer board with the underside
paddle soldered to a pad, which is thermally connected to a
PCB plane.
ESD CAUTION
–40
–20
0
20
40
60
80
100
AMBIENT TEMPERATURE (°C)
Figure 2. Maximum Power Dissipation vs. Temperature for a 4-Layer Board
Rev. A | Page 7 of 24
AD8145
PIN CONFIGURATION AND FUNCTION DESCRIPTION
GND
REF_G
GAIN_G
IN+_G
1
2
3
4
5
6
7
8
24 GND
PIN 1
INDICATOR
23 OUT_B
22 OUT_G
21 OUT_R
AD8145
IN–_G
20 V
S+
TOP VIEW
REF_R
GAIN_R
GND
19 COMPB_IN+
18 COMPB_IN–
17 GND
(Not to Scale)
NOTES
1. EXPOSED PAD ON UNDERSIDE OF DEVICE
MUST BE CONNECTED TO GROUND.
Figure 3. Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
Mnemonic
Description
1, 8, 9, 16, 17, 24, 25, 32
2
GND
REF_G
Signal Ground and Thermal Plane Connection. (See the Absolute Maximum Ratings section.)
Reference Input, Green Channel.
3
4
5
GAIN_G
IN+_G
IN−_G
Gain Connection, Green Channel.
Noninverting Input, Green Channel.
Inverting Input, Green Channel.
6
REF_R
Reference Input, Red Channel.
7
10
11
GAIN_R
IN+_R
IN−_R
Gain Connection, Red Channel.
Noninverting Input, Red Channel.
Inverting Input, Red Channel.
12
13
14
COMPA_IN+
COMPA_IN−
COMPA_OUT
Positive Input, Comparator A.
Negative Input, Comparator A.
Output, Comparator A.
15
COMPB_OUT Output, Comparator B.
18
19
20
COMPB_IN−
COMPB_IN+
VS+
Negative Input, Comparator B.
Positive Input, Comparator B.
Positive Power Supply.
21
22
23
26
OUT_R
OUT_G
OUT_B
VS−
Output, Red Channel.
Output, Green Channel.
Output, Blue Channel.
Negative Power Supply.
27
DIS/PD
REF_B
GAIN_B
IN+_B
IN−_B
GND
Disable/Power Down.
28
29
30
31
Reference Input, Blue Channel.
Gain Connection, Blue Channel.
Noninverting Input, Blue Channel.
Inverting Input, Blue Channel.
Signal Ground and Thermal Plane Connection.
Exposed Underside Pad
Rev. A | Page 8 of 24
AD8145
TYPICAL PERFORMANCE CHARACTERISTICS
Unless otherwise noted, G = 1, RL = 150 Ω, CL = 2 pF, REF_x = midsupply, VS = 5 V, TA = 25°C. Refer to the circuit in Figure 35.
3
2
3
2
+5V
±5V
+5V
±5V
1
1
0
0
–1
–2
–3
–4
–5
–6
–7
–1
–2
–3
–4
–5
–6
–7
V
= 2V p-p
V
= 0.2V p-p
OUT
OUT
1
10
100
1000
1
10
100
1000
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 4. Small Signal Frequency Response at Various Power Supplies, G = 1
Figure 7. Large Signal Frequency Response at Various Power Supplies, G = 1
9
8
7
6
5
4
3
9
8
7
6
5
4
3
+5V ±5V
+5V
±5V
2
1
2
1
0
0
V
= 0.2V p-p
V
= 2V p-p
OUT
OUT
–1
–1
1
10
100
1000
1
10
100
1000
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 5. Small Signal Frequency Response at Various Power Supplies, G = 2
Figure 8. Large Signal Frequency Response at Various Power Supplies, G = 2
3
2
3
2
1
0
1
0
–1
–1
–2
–3
–4
–5
–6
–7
G = 2, C = 10 + 2pF, R
SNUB
= 20Ω
= 20Ω
L
= 20Ω
= 20Ω
SNUB
G = 2, C = 0 + 2pF, R
= 0Ω
L
SNUB
= 0Ω
–2
–3
–4
–5
–6
–7
G = 1, C = 10 + 2pF, R
L
SNUB
G = 1, C = 0 + 2pF, R
= 0Ω
L
SNUB
G = 1, C = 0 + 2pF, R
= 0Ω
L
SNUB
V
= 2V p-p
V
= 0.2V p-p
OUT
OUT
1
10
100
1000
1
10
100
1000
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 6. Small Signal Frequency Response at Various Gains
and 10 pF Capacitive Load Buffered by 20 Ω Resistor
Figure 9. Large Signal Frequency Response at Various Gains
and 10 pF Capacitive Load Buffered by 20 Ω Resistor
Rev. A | Page 9 of 24
AD8145
3
3
2
2
1
1
G = 1
G = 1
0
0
–1
–2
–3
–4
–5
–1
–2
–3
–4
–5
–6
–7
G = 2
G = 2
–6
V
–7
1
= 0.2V p-p
V
= 2V p-p
OUT
OUT
10
100
1000
1
10
100
1000
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 13. Large Signal Frequency Response at Various Gains
Figure 10. Small Signal Frequency Response at Various Gains
1000
0.5
G = 1, V = +5V
S
0.4
0.3
G = 1, V = ±5V
S
0.2
0.1
100
0
G = 2, V = +5V
S
–0.1
–0.2
–0.3
–0.4
–0.5
G = 2, V = ±5V
S
V
= 2V p-p
OUT
10
0.01
0.1
1
10
100
1000
10000 100000
1
10
100
1000
FREQUENCY (kHz)
FREQUENCY (MHz)
Figure 14. Input Referred Voltage Noise vs. Frequency
Figure 11. 0.1 dB Flatness for Various Power Supplies and Gains
110
100
90
4
3
2
1
0
R
= OPEN CIRCUIT
L
G = 1
= ±5V
V
S
80
V
= +5V
S
70
60
50
40
30
20
10
V
= ±5V
S
–1
–2
–3
–4
0.1
1
10
FREQUENCY (MHz)
100
1000
–5
–4
–3
–2
–1
0
1
2
3
4
5
DIFFERENTIAL INPUT VOLTAGE (V)
Figure 12. Common-Mode Rejection vs. Frequency at Various Supplies
Figure 15. Differential Input Operating Range
Rev. A | Page 10 of 24
AD8145
150
100
50
1.5
1.0
BLACK = +5V
GRAY = ±5V
BLACK = +5V
GRAY = ±5V
0.5
0
0
–50
–100
–150
–0.5
–1.0
–1.5
V
= 2V p-p
20
V
= 0.2V p-p
OUT
OUT
0
10
20
30
40
50
60
70
80
90
100
0
10
30
40
50
60
70
80
90
100
TIME (ns)
TIME (ns)
Figure 16. Small Signal Transient Response at Various Power Supplies, G = 1
Figure 19. Large Signal Transient Response at Various Power Supplies, G = 1
150
100
1.5
1.0
BLACK = +5V
GRAY = ±5V
BLACK = +5V
GRAY = ±5V
50
0
0.5
0
–50
–100
–0.5
–1.0
V
= 2V p-p
20
V
= 0.2V p-p
20
OUT
OUT
–150
–1.5
0
10
30
40
50
60
70
80
90
100
0
10
30
40
50
60
70
80
90
100
TIME (ns)
TIME (ns)
Figure 17. Small Signal Transient Response at Various Power Supplies, G = 2
Figure 20. Large Signal Transient Response at Various Power Supplies, G = 2
150
1.5
G = 1, C = 0 + 2pF, R
SNUB
= 0Ω
= 20Ω
G = 1, C = 0 + 2pF, R
SNUB
= 0Ω
= 20Ω
L
L
G = 1, C = 10 + 2pF, R
G = 1, C = 10 + 2pF, R
L
SNUB
L
SNUB
100
50
1.0
0.5
V = 2V p-p
OUT
V
= 0.2V p-p
OUT
0
0
–50
–100
–150
–0.5
–1.0
–1.5
G = 2, C = 0 + 2pF, R
L
= 0Ω
G = 2, C = 0 + 2pF, R
L
= 0Ω
SNUB
SNUB
G = 2, C = 10 + 2pF, R
= 20Ω
G = 2, C = 10 + 2pF, R
= 20Ω
L
SNUB
L
SNUB
0
10
20
30
40
50
60
70
80
90
100
0
10
20
30
40
50
60
70
80
90
100
TIME (ns)
TIME (ns)
Figure 18. Small Signal Transient Response at Various Gains
and 10 pF Capacitive Load Buffered by 20 Ω Resistor
Figure 21. Large Signal Transient Response at Various Gains
and 10 pF Capacitive Load Buffered by 20 Ω Resistor
Rev. A | Page 11 of 24
AD8145
2.0
0.5
4500
4000
3500
3000
2500
2000
1500
1000
500
POSITIVE
SLEW RATE
1.6
0.4
OUTPUT
INPUT
1.2
0.3
0.8
0.4
0.2
NEGATIVE
SLEW RATE
0.1
ERROR
0
0
–0.4
–0.8
–1.2
–1.6
–2.0
–0.1
–0.2
–0.3
–0.4
–0.5
0
0
5
10
15
20
25
TIME (ns)
30
35
40
45
50
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
OUTPUT VOLTAGE (V p-p)
Figure 22. Settling Time
Figure 25. Slew Rate vs. Output Voltage Swing
–50
–55
–60
–65
–70
–75
–80
–50
–60
V
= +5V
S
–70
–80
V
= ±5V
S
V
= ±5V
= +5V
S
–90
–100
–110
–120
V
S
V
= 2V p-p
V
= 2V p-p
OUT
OUT
0.1
1
10
FREQUENCY (MHz)
100
0.1
1
10
FREQUENCY (MHz)
100
Figure 26. Third Harmonic Distortion vs. Frequency and Power Supplies,
OUT = 2 V p-p, G = 1
Figure 23. Second Harmonic Distortion vs. Frequency and Power Supplies,
VOUT = 2 V p-p, G = 1
V
–50
–50
–60
V
= 2V p-p
OUT
–55
–60
–65
–70
–75
–80
V
= +5V
S
–70
V
= ±5V
S
–80
–90
V
V
= ±5V
= +5V
S
S
–100
–110
–120
V
= 2V p-p
OUT
0.1
1
10
FREQUENCY (MHz)
100
0.1
1
10
FREQUENCY (MHz)
100
Figure 24. Second Harmonic Distortion vs. Frequency and Power Supplies,
OUT = 2 V p-p, G = 2
Figure 27. Third Harmonic Distortion vs. Frequency and Power Supplies,
OUT = 2 V p-p, G = 2
V
V
Rev. A | Page 12 of 24
AD8145
65
60
55
50
45
40
35
30
25
20
15
5
4
R
= OPEN CIRCUIT
L
3
I
(±5V)
CC
2
I
(±5V)
1
EE
0
–1
–2
–3
–4
–5
+5V OUTPUT
I
(±2.5V)
EE
+5V 2 × V
IN
I
(±2.5V)
20
±5V OUTPUT
CC
±5V 2 × V
IN
G = 2
50
–60
–40
–20
0
40
60
80
100
120
0
100 150 200 250 300 350 400 450 500
TIME (ns)
TEMPERATURE (°C)
Figure 28. Power Supply Current vs. Temperature
Figure 31. Output Overdrive Recovery
10
0
10
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–10
–20
–30
–40
–50
–60
–70
–80
–90
BLACK = ±2.5V
GRAY = ±5V
BLACK = +5V
GRAY = ±5V
0.01
0.1
1
10
100
1000
0.01
0.1
1
10
100
1000
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 32. Negative Power Supply Rejection Ratio (PSRR) vs. Frequency
Figure 29. Positive Power Supply Rejection Ratio (PSRR) vs. Frequency
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
–15
–10
–5
0
5
10
15
V
(mV)
IN
Figure 30. Comparator Hysteresis
Rev. A | Page 13 of 24
AD8145
THEORY OF OPERATION
The AD8145 amplifiers use an architecture called active feedback,
which differs from that of conventional op amps. The most
obvious differentiating feature is the presence of two separate
pairs of differential inputs compared to a conventional op amp’s
single pair. Typically, for the active feedback architecture, one of
these input pairs is driven by a differential input signal while
the other is used for the feedback. This active stage in the feedback
path is where the term active feedback is derived. The AD8145
has an internal feedback resistor from each amplifier output to
the negative input of its feedback input stage. This limits the
possible closed-loop gain configurations for the AD8145.
The two differential input stages of the AD8145 are each
transconductance stages that are well matched. These stages
convert the respective differential input voltages to internal
currents. The currents are then summed and converted to a
voltage, which is buffered to drive the output. The compensation
capacitor is included in the summing circuit. When the feedback
path is closed around the part, the output drives the feedback
input to the voltage that causes the internal currents to sum to
zero. This occurs when the two differential inputs are equal and
opposite; that is, their algebraic sum is zero.
In a closed-loop application, a conventional op amp has its
differential input voltage driven to near zero under non-
transient conditions. The AD8145 generally has differential
input voltages at each of its input pairs, even under equilibrium
conditions. As a practical consideration, it is necessary to limit
the differential input voltage internally with a clamp circuit.
Therefore, the input dynamic ranges are limited to approximately
2.5 V (see the Specifications section for more details). For this
reason, it is not recommended to reverse the input and feedback
stages of the AD8145, even though some normal functionality
may be observed under some conditions.
The active feedback architecture offers several advantages over a
conventional op amp in several types of applications. Among
these are excellent common-mode rejection, wide input common-
mode range, and a pair of inputs that are high impedance and
completely balanced in a typical application. In addition, while
an external feedback network establishes the gain response as in a
conventional op amp, its separate path makes it entirely independent
of the signal input. This eliminates any interaction between the
feedback and input circuits, which traditionally causes problems
with CMRR in conventional differential-input op amp circuits.
Another advantage of active feedback is the ability to change the
polarity of the gain merely by switching the differential inputs.
A high input impedance inverting amplifier can therefore be
made. Besides high input impedance, a unity-gain inverter with
the AD8145 has a noise gain of unity, producing lower output
noise and higher bandwidth than op amps that have noise gain
equal to 2 for a unity-gain inverter.
Rev. A | Page 14 of 24
AD8145
APPLICATIONS INFORMATION
+5V
OVERVIEW
The AD8145 contains three independent active feedback amplifiers
that can be effectively applied as differential line receivers for
red-green-blue (RGB) signals or component video signals, such
as YPbPr, transmitted over UTP cable. The AD8145 also contains
two general-purpose comparators with hysteresis that can be
used to receive digital signals or to extract video synchronization
pulses from received common-mode signals that contain
encoded synchronization signals.
0.01µF
V
IN
OUT
V
REF
OUT
V
REF
R
The comparators, which receive power from the positive supply, are
referenced to GND and require greater than 4.5 V on the positive
supply for proper operation. If the comparators are not used,
then a split 2.5 V can be used with the amplifiers operating
normally.
R
C
GAIN
0.01µF
–5V
The AD8145 includes a power-down feature that can be asserted to
reduce the supply current when a particular device is not in use.
Figure 33. Basic Gain = 1 Circuit: VOUT = VIN + VREF
The gain equation for the circuit in Figure 33 is
OUT = VIN + VREF
BASIC CLOSED-LOOP GAIN CONFIGURATIONS
V
(1)
Each amplifier in the AD8145 comprises two transconductance
amplifiers—one for the input signal and one for negative feedback.
Note that the closed-loop gain of the amplifier used in the signal
path is defined as the single-ended output voltage of the amplifier
divided by its differential input voltage. Therefore, each amplifier
in the AD8145 provides differential-to-single-ended gain.
Additionally, the amplifier used for feedback has two high
impedance inputs—the feedback input, where the negative
feedback is applied, and the REF input, that can be used as
an independent single-ended input to apply a dc offset to the
output signal.
In this configuration, the voltage applied to the REF pin appears
at the output with a gain of 1.
Figure 34 illustrates one way to operate an AD8145 amplifier
with a gain of 2.
+5V
0.01µF
V
IN
REF
The AD8145 contains on-chip feedback networks between each
amplifier output and its respective feedback input. The closed-
loop gain of the amplifier is set to 1 by connecting the amplifier
output directly to its respective GAIN_x pin. Doing this places
the on-chip resistors and capacitor in parallel across the amplifier
output and feedback pin. The small feedback capacitor mitigates
the effects of the summing-node capacitance, which is most
problematic in the unity gain case. Closed-loop gain of an
amplifier is set to 2 by connecting the respective GAIN_x pin
to a reference voltage, often directly to ground. In Figure 1,
R = 350 ꢀ and C = 2 pF.
V
OUT
V
REF
C
R
GAIN
R
0.01µF
–5V
Figure 34. Basic Gain = 2 Circuit: VOUT = 2(VIN + VREF
)
The gain equation for the circuit in Figure 34 is
OUT = 2(VIN + VREF
V
)
(2)
Some basic gain configurations implemented with an AD8145
amplifier are shown in Figure 33 through Figure 36.
Rev. A | Page 15 of 24
AD8145
To achieve unity gain from VREF to VOUT in this configuration,
divide VREF by the same factor used in the feedback loop; the
divider resistors, RD, need not be the same values used in the
internal feedback loop. Figure 35 illustrates this approach.
+5V
TERMINATING THE INPUT
One of the key benefits of the active feedback architecture is the
separation that exists between the differential input signal and
the feedback network. Because of this separation, the differential
input maintains its high CMRR and provides high differential
and common-mode input impedances, making line termination
a simple task.
0.01µF
Most applications that use the AD8145 involve transmitting broad-
band video signals over 100 Ω UTP cables and use dc-coupled
terminations. The two most common types of dc-coupled
terminations are differential and common-mode. Differential
termination of 100 Ω UTP cables is implemented by simply
connecting a 100 Ω resistor across the amplifier input, as shown
in Figure 37.
V
IN
R
REF
D
V
OUT
R
D
V
REF
C
R
GAIN
R
+5V
0.01µF
–5V
0.01µF
Figure 35. Basic Gain Circuit: VOUT = 2VIN + VREF
100Ω
UTP
The gain equation for the circuit in Figure 35 is
OUT = 2VIN + VREF
V
100Ω
IN
OUT
V
(3)
V
REF
OUT
Another configuration that provides the same gain equation as
Equation 3 is shown in Figure 36. In this configuration, it is
important to keep the source resistance of VREF much smaller
than 350 ꢀ to avoid gain errors.
R
R
C
+5V
GAIN
0.01µF
0.01µF
–5V
V
IN
Figure 37. Differential-Mode Termination with G = 1
REF
V
OUT
Some applications require common-mode terminations for
common-mode currents generated at the transmitter. In these
cases, the 100 Ω termination resistor is split into two 50 Ω
resistors. The required common-mode termination voltage is
applied at the tap between the two resistors. In many of these
applications, the common-mode tap is connected to ground
(VTERM (CM) = 0). This scheme is illustrated in Figure 38.
+5V
C
R
R
GAIN
V
REF
0.01µF
–5V
Figure 36. Basic Gain Circuit: VOUT = 2VIN + VREF
For stability reasons, the inductance of the trace connected to
the REF_x pin must be kept to less than 10 nH. The typical
inductance of 50 Ω traces on the outer layers of the FR-4 boards
is 7 nH/in, and on the inner layers, it is typically 9 nH/in. Vias
must be accounted for as well. The inductance of a typical via in
a 0.062-inch board is 1.5 nH. If longer traces are required, a 200 Ω
resistor should be placed in series with the trace to reduce the
Q-factor of the inductance.
0.01µF
50Ω
100Ω
UTP
V
IN
50Ω
OUT
V
REF
V
(CM)
OUT
TERM
R
In many dual-supply applications, VREF can be directly connected to
ground right at the device.
R
C
GAIN
0.01µF
–5V
Figure 38. Common-Mode Termination with G = 1
Rev. A | Page 16 of 24
AD8145
A simple way to implement a clamp is to use a number of diodes in
series. The resultant clamping voltage is then the sum of the
clamping voltages of individual diodes.
INPUT CLAMPING
The differential input that is assigned to receive the input signal
includes clamping diodes that limit the differential input swing
to approximately 5.5 V p-p at 25°C. Because of this, the input
and feedback stages should never be interchanged.
A 1N4448 diode has a forward voltage of approximately 0.70 V
to 0.75 V at typical current levels that are seen when it is being
used as a clamp, and 2 pF maximum capacitance at 0 V bias.
(The capacitance of a diode decreases as its reverse-bias voltage
is increased.) The series connection of two 1N4448 diodes,
therefore, has a clamping voltage of 1.4 V to 1.5 V. Figure 40
shows how to limit the differential input voltage applied to an
AD8145 amplifier to ±1.4 V to ±1.5 V (2.8 V p-p to 3.0 V p-p).
Note that the capacitance of the two series diodes is half that of
one diode. Different numbers of series diodes can be used to
obtain different clamping voltages.
The supply current drawn by the AD8145 has a strong dependence
on the input signal magnitude because the input transconductance
stages operate with differential input signals that can be up to a
few volts peak-to-peak. This behavior is distinctly different
from that of traditional op amps, where the differential input
signal is driven to essentially 0 V by negative feedback.
For most applications, including receiving RGB video signals,
the input signal magnitudes encountered are well within the
safe operating limits of the AD8145 over its full power supply
and operating temperature ranges. In some extreme applications
where large differential and/or common-mode voltages are
encountered, external clamping may be necessary. External
common-mode clamping is also sometimes required when an
unpowered AD8145 receives a signal from an active driver. In
this case, external diodes are required when the current drawn
by the internal ESD diodes cannot be kept to less than 5 mA.
RT is the differential termination resistor, and the series
resistances, RS, limit the current into the diodes. The series
resistors should be highly matched in value to preserve high
frequency CMRR.
+5V
POSITIVE CLAMP
NEGATIVE CLAMP
0.01µF
+
R
S
Figure 39 shows a general approach to external differential-mode
clamping.
V
IN
R
T
R
OUT
S
–
+5V
V
REF
POSITIVE CLAMP NEGATIVE CLAMP
OUT
+
0.01µF
R
S
R
V
–
IN
R
T
R
C
OUT
GAIN
R
S
V
REF
OUT
0.01µF
–5V
R
Figure 40. Using Two 1N4448 Diodes in Series as a Clamp
R
C
Many other nonlinear devices can be used as clamps. The best
choice for a particular application depends upon the desired
clamping voltage, response time, parasitic capacitance, and
other factors.
GAIN
0.01µF
–5V
Figure 39. Differential-Mode Clamping with G = 1
When using external differential-mode clamping, it is important
to ensure that the series resistors (RS), the sum of the parasitic
capacitance of the clamping devices, and the input capacitance
of the AD8145 are small enough to preserve the desired signal
bandwidth.
The positive and negative clamps are nonlinear devices that exhibit
very low impedance when the voltage across them reaches a
critical threshold (clamping voltage), thereby limiting the voltage
across the AD8145 input. The positive clamp has a positive
threshold, and the negative clamp has a negative threshold.
A diode is a simple example of such a clamp. Schottky diodes
generally have lower clamping voltages than typical signal diodes.
The clamping voltage should be larger than the largest expected
signal amplitude, with enough margin to ensure that the received
signal passes without being distorted.
Rev. A | Page 17 of 24
AD8145
Figure 41 shows a specific example of external common-mode
clamping.
not required. In these cases, small series resistors should be used to
buffer the capacitance presented by the load.
V+
2
Broadband power supply decoupling networks should be placed
as close as possible to the supply pins. Small surface-mount ceramic
capacitors are recommended for these networks, and tantalum
capacitors are recommended for bulk supply decoupling.
+5V
3
+
R
S
0.01µF
1
V–
HBAT-540C
Minimizing Parasitic Feedback Reactances
V
–
R
T
IN
Parasitic trace capacitance and inductance are both reduced in
the unity-gain configuration when the feedback trace that connects
the OUT_x pin to the GAIN_x pin is reduced in length. Removing
the copper from the planes below the trace reduces trace capacitance,
but increases trace inductance, because the loop area formed by
the trace and ground plane is increased. A reasonable compromise
that works well is to void all copper directly under the feedback
trace and component pads with margins on each side approximately
equal to one trace width. Combining this technique with minimizing
trace length is effective in keeping parasitic trace reactance in
the unity-gain feedback loop to a minimum.
V+
2
OUT
V
REF
OUT
R
S
3
R
1
V–
HBAT-540C
R
C
GAIN
0.01µF
–5V
Figure 41. External Common-Mode Clamping
Maximizing Heat Removal
A square array of thermal vias works well to connect the exposed
paddle to internal ground planes. The vias should be placed
inside the PCB pad that is soldered to the exposed paddle and
should connect to all ground planes.
The series resistances, RS, limit the current in each leg, and the
Schottky diodes limit the voltages on each input to approximately
0.3 V to 0.4 V over the positive power supply, V+, and to 0.3 V
to 0.4 V below the negative power supply, V−. The required
signal bandwidth, the line impedance, and the effective
differential capacitance due to the AD8145 inputs and the
diodes determine the maximum RS value.
The AD8145 includes ground connections on its corner pins.
These pins can be used to provide additional heat removal from
the AD8145 by connecting them between the PCB pad that is
soldered to the exposed paddle and a ground plane on the
component side of the board. This layout technique lowers the
overall package thermal resistance. Use of this technique is not
required, but it does result in a lower junction temperature. Designs
must often conform to Design for Manufacturing (DFM) rules
that stipulate how to lay out PCBs in such a way as to facilitate
the manufacturing process. Some of these rules require thermal
relief on pads that connect to planes, and the rules may limit the
extent to which this technique can be used.
As with the differential clamp, the series resistors should be
highly matched in value to preserve high frequency CMRR.
PCB LAYOUT CONSIDERATIONS
The two most important issues with regard to PCB layout are
minimizing parasitic signal trace reactances in the feedback
network and providing sufficient thermal relief.
Excessive parasitic reactances in the feedback network cause
excessive peaking in the frequency response of the amplifier
and excessive overshoot in its step response due to a reduction
in phase margin. Oscillation occurs when these parasitic
reactances are increased to a critical point where the phase margin
is reduced to zero. Minimizing these reactances is important to
obtain optimal performance from the AD8145. General high
speed layout practices should be adhered to when applying the
AD8145. Controlled impedance transmission lines are required
for incoming and outgoing signals, referenced to a ground plane.
Typically, the input signals are received over 100 Ω differential
transmission lines. A 100 Ω differential transmission line is readily
realized on the PCB using two well-matched, closely-spaced,
50 Ω single-ended traces that are coupled through the ground
plane. The traces that carry the single-ended output signals are
most often 75 Ω for video signals. Output signal connections
should include series termination resistors that are matched to
the impedance of the line they are driving. When driving high
impedance loads over very short traces, impedance matching is
Rev. A | Page 18 of 24
AD8145
DRIVING A CAPACITIVE LOAD
POWER-DOWN
The AD8145 typically drives either high impedance loads over
short PCB traces, such as crosspoint switch inputs, or doubly
terminated coaxial cables. A gain of 1 is commonly used in
the high impedance case because a 6 dB transmission line
termination loss is not incurred. A gain of 2 is required when
driving cables to compensate for the 6 dB termination loss.
The power-down feature can be used to reduce power consumption
when a particular device is not in use and does not place the output
in a high-Z state when asserted. The power-down feature is
asserted when the voltage applied to the power-down pin drops
to approximately 2 V below the positive supply. The AD8145 is
enabled by pulling the power-down pin to the positive supply.
In all cases, the output must drive the parasitic capacitance of
the feedback loop, conservatively estimated to be 1 pF, in addition
to the capacitance presented by the actual load. When driving a
high impedance input, it is recommended that a small series
resistor be used to buffer the input capacitance of the device
being driven. Clearly, the resistor value must be small enough to
preserve the required bandwidth. In the ideal doubly terminated
cable case, the AD8145 output sees a purely resistive load. In
reality, there is some residual capacitance, which is buffered by
the series termination resistor. Figure 42 illustrates the high
impedance case, and Figure 43 illustrates the cable driving case.
+5V
AUTOMOTIVE PRODUCTS
The AD8145W product is qualified per the AEC-Q100 for use
in automotive applications. This model meets stringent automotive
performance and quality requirements and offers the same
functionalities as the commercial and industrial grade devices but
operates over a temperature range of −40°C to +105°C. For more
information, contact your local Analog Devices, Inc., sales
representative.
COMPARATORS
In addition to general-purpose applications, the two on-chip
comparators can be used to decode video sync pulses from the
received common-mode voltages or to receive differential digital
information. Built-in hysteresis helps to eliminate false triggers
from noise.
0.01µF
V
IN
The comparator outputs are designed to drive source-terminated
transmission lines. The source termination technique uses a resistor
in-series with each comparator output such that the sum of the
comparator source resistance (≈20 ꢀ) and the series resistor
equals the transmission line characteristic impedance. The load
end of the transmission line is high impedance. When the signal
is launched into the source termination, its initial value is one-
half of its source value because its amplitude is divided-by-2 by
the voltage divider formed by the source termination and the
transmission line. At the load, the signal experiences nearly
100% positive reflection due to the high impedance load and
is restored to nearly its full value. This technique is commonly
used in PCB layouts that involve high speed digital logic.
R
OUT
S
REF
C
IN
V
REF
R
R
C
GAIN
0.01µF
–5V
Figure 42. Buffering the Input Capacitance of a High-Z Load with G = 1
An internal linear voltage regulator derives power for the
comparators from the positive supply; therefore, the AD8145
must always have a minimum positive supply voltage of 4.5 V.
+5V
0.01µF
V
IN
R
OUT
S
REF
C
R
S
L
V
REF
C
R
GAIN
R
0.01µF
–5V
Figure 43. Driving a Doubly Terminated Cable with G = 2
Rev. A | Page 19 of 24
AD8145
The AD8134 encoding equations are given in Equation 4,
Equation 5, and Equation 6.
SYNC PULSE EXTRACTION USING COMPARATORS
The AD8145 is particularly useful in KVM applications. KVM
networks transmit and receive computer video signals that typically
comprise red, green, and blue (RGB) video signals and separate
horizontal and vertical sync signals. Because the sync signals are
separate and not embedded in the color signals, it is advantageous
to transmit them using a simple scheme that encodes them among
the three common-mode voltages of the RGB signals. The AD8134
triple differential driver is a natural complement to the AD8145
and performs the sync pulse encoding with the necessary
circuitry on-chip.
K
2
Red VCM
=
V − H
]
(4)
(5)
(6)
K
2
Green VCM
=
−2 V
]
K
2
Blue VCM
where:
=
V + H
]
Red VCM, Green VCM, and Blue VCM are the transmitted common-
mode voltages of the respective color signals.
K is an adjustable gain constant that is set by the AD8134.
V and H are the vertical and horizontal sync pulses, defined
with a weight of −1 when the pulses are in their low states and a
weight of +1 when they are in their high states.
The AD8134 data sheet contains further details regarding the
encoding scheme. Figure 44 illustrates how the AD8145 comparators
can be used to extract the horizontal and vertical sync pulses that
are encoded on the RGB common-mode voltages by the AD8134.
50Ω
RED CMV
RECEIVED
RED VIDEO
R
S
HSYNC
50Ω
1kΩ
47pF
47pF
50Ω
GREEN CMV
475Ω
RECEIVED
GREEN VIDEO
R
S
VSYNC
50Ω
1kΩ
50Ω
BLUE CMV
RECEIVED
BLUE VIDEO
50Ω
Figure 44. Extracting Sync Signals from Received Common-Mode Signal
Rev. A | Page 20 of 24
AD8145
OUTLINE DIMENSIONS
5.00
BSC SQ
0.60 MAX
0.60 MAX
PIN 1
INDICATOR
25
24
32
1
PIN 1
INDICATOR
0.50
BSC
EXPOSED
PAD
(BOTTOM VIEW)
3.45
3.30 SQ
3.15
TOP
VIEW
4.75
BSC SQ
0.50
0.40
0.30
17
16
8
9
0.25 MIN
0.80 MAX
0.65 TYP
3.50 REF
12° MAX
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
0.05 MAX
0.02 NOM
COPLANARITY
1.00
0.85
0.80
0.30
0.23
0.18
SECTION OF THIS DATA SHEET.
0.08
0.20 REF
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-220-VHHD-2
Figure 45. 32-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
5 mm × 5 mm Body, Very Thin Quad
(CP-32-3)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
AD8145YCPZ-R2
AD8145YCPZ-RL
AD8145YCPZ-R7
AD8145WYCPZ-R72
Temperature Range
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
Package Description
Package Option
32-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
CP-32-3
CP-32-3
CP-32-3
CP-32-3
1 Z = RoHS Compliant Part.
2 W = automotive qualified product.
Rev. A | Page 21 of 24
AD8145
NOTES
Rev. A | Page 22 of 24
AD8145
NOTES
Rev. A | Page 23 of 24
AD8145
NOTES
©2006–2010 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06307-0-1/10(A)
Rev. A | Page 24 of 24
相关型号:
AD8146ACPZ-R21
IC 1 CHANNEL, VIDEO AMPLIFIER, QCC24, 4 X 4 MM, ROHS COMPLIANT, MO-220VGGD-2, LFCSP-24, Audio/Video Amplifier
ADI
AD8146ACPZ-R71
IC 1 CHANNEL, VIDEO AMPLIFIER, QCC24, 4 X 4 MM, ROHS COMPLIANT, MO-220VGGD-2, LFCSP-24, Audio/Video Amplifier
ADI
AD8146ACPZ-RL1
IC 1 CHANNEL, VIDEO AMPLIFIER, QCC24, 4 X 4 MM, ROHS COMPLIANT, MO-220VGGD-2, LFCSP-24, Audio/Video Amplifier
ADI
©2020 ICPDF网 联系我们和版权申明