AD8190ACPZ [ADI]
2:1 HDMI/DVI Switch with Equalization; 2 ： 1 HDMI / DVI开关，具有均衡
| 型号： | AD8190ACPZ |
| 厂家： | 
ADI |
| 描述： | 2:1 HDMI/DVI Switch with Equalization |
| 文件： | 总24页 (文件大小：799K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
2:1 HDMI/DVI Switch with Equalization
AD8190
FUNCTIONAL BLOCK DIAGRAM
FEATURES
RESET
Two inputs, one output HDMI/DVI links
Enables HDMI 1.2a-compliant receiver
Four TMDS channels per link
SERIAL INTERFACE
AVCC
DVCC
AD8190
I2C_SDA
I2C_SCL
I2C_ADDR
CONFIG
INTERFACE
CONTROL
LOGIC
AMUXVCC
AVEE
DVEE
Supports 250 Mbps to 1.65 Gbps data rates
Supports 25 MHz to 165 MHz pixel clocks
VTTI
Equalized inputs for operation with long HDMI cables
(20 meters at 1080p)
Fully buffered unidirectional inputs/outputs
Globally switchable 50 Ω on-chip terminations
Pre-emphasized outputs
Low added jitter
Single-supply operation (3.3 V)
Four auxiliary channels per link
VTTO
+
4
4
IP_A[3:0]
IN_A[3:0]
+
–
4
SWITCH
CORE
–
+
OP[3:0]
ON[3:0]
4
EQ
PE
4
4
IP_B[3:0]
IN_B[3:0]
4
–
HIGH SPEED
BUFFERED
VTTI
4
4
AUX_A[3:0]
SWITCH
CORE
AUX_COM[3:0]
Bidirectional unbuffered inputs/outputs
Flexible supply operation (3.3 V to 5 V)
HDCP standard compatible
AUX_B[3:0]
LOW SPEED
UNBUFFERED
BIDIRECTIONAL
Allows switching of DDC bus and two additional signals
Output disable feature
Figure 1.
Reduced power dissipation
Output termination removal
TYPICAL APPLICATION
HDTV SET
Two AD8190s support HDMI/DVI dual-link
Standards compliant: HDMI receiver, HDCP, DVI
Serial (I2C slave) control interface
56-lead, 8 mm x 8 mm, LFCSP, Pb-free package
HDMI
RECEIVER
SET-TOP BOX
DVD PLAYER
DVD
01:18
AD8190
APPLICATIONS
Figure 2. Typical AD8190 Application for HDTV Sets
Multiple input displays
Projectors
A/V receivers
Set-top boxes
Advanced television (HDTV) sets
GENERAL DESCRIPTION
PRODUCT HIGHLIGHTS
The AD8190 is an HDMI/DVI switch featuring equalized
TMDS inputs and pre-emphasized TMDS outputs, ideal for
systems with long cable runs. Outputs can be set to a high
impedance state to reduce the power dissipation and/or allow
the construction of larger arrays using the wire-OR technique.
1. Supports data rates up to 1.65 Gbps, enabling UXGA
(1600 × 1200) DVI resolutions and 1080p HDMI formats.
2. Input cable equalizer enables use of long cables at the
input (more than 20 meters of 24 AWG cable at 1080p).
3. Auxiliary switch allows routing of the DDC bus and two
additional single-ended signals for a single chip, fully
HDMI 1.2a receive-compliant solution.
The AD8190 is provided in a space saving, 56-lead, LFCSP,
surface-mount, Pb-free, plastic package and is specified to
operate over the −40°C to +85°C temperature range.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2006 Analog Devices, Inc. All rights reserved.
AD8190
TABLE OF CONTENTS
Features .............................................................................................. 1
Serial Control Interface ................................................................. 14
Reset............................................................................................. 14
Write Procedure.......................................................................... 14
Read Procedure........................................................................... 15
Switching/Update Delay............................................................ 15
Configuration Registers................................................................. 16
High Speed Device Modes Register ......................................... 16
Auxiliary Device Modes Register............................................. 16
Receiver Settings Register ......................................................... 17
Input Termination Pulse Register ............................................ 17
Receive Equalizer Register ........................................................ 17
Transmitter Settings Register.................................................... 17
Application Notes........................................................................... 18
Pinout........................................................................................... 18
Cable Lengths and Equalization............................................... 19
The AD8190 as a Single-Channel Buffer ................................ 19
PCB Layout Guidelines.............................................................. 19
Outline Dimensions....................................................................... 23
Ordering Guide .......................................................................... 23
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
Typical Application........................................................................... 1
General Description......................................................................... 1
Product Highlights ........................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Absolute Maximum Ratings............................................................ 5
Thermal Resistance ...................................................................... 5
Maximum Power Dissipation ..................................................... 5
ESD Caution.................................................................................. 5
Pin Configuration and Function Descriptions............................. 6
Typical Performance Characteristics ............................................. 8
Theory of Operation ...................................................................... 12
Introduction................................................................................ 12
Input Channels............................................................................ 12
Output Channels ........................................................................ 12
Switching Mode .......................................................................... 13
Auxiliary Lines Switching.......................................................... 13
REVISION HISTORY
7/06—Revision 0: Initial Version
Rev. 0 | Page 2 of 24
AD8190
SPECIFICATIONS
TA = 27°C, AVCC = 3.3 V, VTTI = 3.3 V, VTTO = 3.3 V, DVCC = 3.3 V, AMUXVCC = 5 V, AVEE = 0 V, DVEE = 0 V, differential input swing =
1000 mV, TMDS outputs terminated with external 50 Ω resistors to 3.3 V, unless otherwise noted.
Table 1.
Parameter
Conditions/Comments
Min
Typ Max
Unit
DYNAMIC PERFORMANCE
Maximum Data Rate (DR) per Channel
Bit Error Rate (BER)
NRZ
PRBS 223 − 1
1.65
Gbps
10−9
DR ≤ 1.65 Gbps, PRBS 223 − 1
Added Deterministic Jitter
Added Random Jitter
40
1
1
ps (p-p)
ps (rms)
ps
Differential Intrapair Skew
Differential Interpair Skew1
EQUALIZATION PERFORMANCE
Receiver (Highest Setting)2
Transmitter (Highest Setting)3
INPUT CHARACTERISTICS
Input Voltage Swing
Input Common-Mode Voltage (VICM
OUTPUT CHARACTERISTICS
High Voltage Level
At output
At output
40
ps
Boost frequency = 825 MHz
Boost frequency = 825 MHz
12
6
dB
dB
Differential
150
AVCC − 800
1200
AVCC
mV
mV
)
Single-ended high speed channel
Single-ended high speed channel
AVCC − 10
AVCC − 600
75
AVCC + 10
mV
Low Voltage Level
Rise/Fall Time (20% to 80%)
AVCC − 400 mV
135 200
ps
INPUT TERMINATION
Resistance
Single-ended
50
Ω
AUXILIARY CHANNELS
On Resistance, RAUX
On Capacitance, CAUX
Input/Output Voltage Range
POWER SUPPLY
AVCC
100
8
Ω
pF
V
DC bias = 2.5 V, ac voltage = 3.5 V, f = 100 kHz
Operating range
DVEE
3
AMUXVCC
3.6
3.3
V
QUIESCENT CURRENT
AVCC
Outputs disabled
30
53
98
5
36
73
40
60
45
66
mA
mA
mA
mA
mA
mA
Outputs enabled, no pre-emphasis
Outputs enabled, maximum pre-emphasis
Input termination on4
Output termination on, no pre-emphasis
Output termination on, maximum
pre-emphasis
108 120
VTTI
VTTO
40
40
80
54
44
88
DVCC
AMUXVCC
4
7
10
mA
mA
0.01 0.1
POWER DISSIPATION
Outputs disabled
Outputs enabled, no pre-emphasis
Outputs enabled, maximum pre-emphasis
115
411
754
271 364
574 664
936 1057
mW
mW
mW
TIMING CHARACTERISTICS
Switching/Update Delay
High speed switching register: HS_CH
All other configuration registers
200
1.5
ms
μs
RESET
50
ns
Pulse Width
Rev. 0 | Page 3 of 24
AD8190
Parameter
Conditions/Comments
Min
2
Typ Max
Unit
SERIAL CONTROL INTERFACE5
Input High Voltage, VIH
Input Low Voltage, VIL
Output High Voltage, VOH
Output Low Voltage, VOL
V
V
V
V
0.8
0.4
2.4
1 Differential interpair skew is measured between the TMDS pairs of a single link.
2 AD8190 output meets the transmitter eye diagram as defined in the DVI Standard Revision 1.0 and the HDMI Standard Revision 1.2a.
3 Cable output meets the receiver eye diagram mask as defined in the DVI Standard Revision 1.0 and the HDMI Standard Revision 1.2a.
4 Typical value assumes only the selected HDMI/DVI link is active with nominal signal swings and that the unselected HDMI/DVI link is deactivated. Minimum and
maximum limits are measured at the respective extremes of input termination resistance and input voltage swing.
5 The AD8190 is an I2C slave and its serial control interface is based on the 3.3 V I2C bus specification.
Rev. 0 | Page 4 of 24
AD8190
ABSOLUTE MAXIMUM RATINGS
Table 2.
THERMAL RESISTANCE
Parameter
AVCC to AVEE
DVCC to DVEE
DVEE to AVEE
VTTI
Rating
3.7 V
3.7 V
θJA is specified for the worst-case conditions: a device soldered
in a 4-layer JEDEC circuit board for surface-mount packages.
θJC is specified for the exposed pad soldered to the circuit board
with no airflow.
0.3 V
AVCC + 0.6 V
AVCC + 0.6 V
5.5 V
Table 3. Thermal Resistance
Package Type
VTTO
AMUXVCC
θJA
θJC
Unit
Internal Power Dissipation 4.62 W
56-Lead LFCSP
27
2.1
°C/W
High Speed Input Voltage AVCC − 1.4V <VIN < AVCC + 0.6 V
High Speed Differential
Input Voltage
2.0 V
MAXIMUM POWER DISSIPATION
Low Speed Input Voltage
I2C Logic Input Voltage
Storage Temperature
Range
Operating Temperature
Range
Junction Temperature
DVEE − 0.3 V <VIN < AMUXVCC + 0.6 V
DVEE − 0.3 V < VIN < DVCC + 0.6 V
−65°C to +125°C
The maximum power that can be safely dissipated by the
AD8190 is limited by the associated rise in junction tempera-
ture. The maximum safe junction temperature for plastic
encapsulated devices is determined by the glass transition
temperature of the plastic, approximately 150°C. Temporarily
exceeding this limit may cause a shift in parametric performance
due to a change in the stresses exerted on the die by the package.
Exceeding a junction temperature of 175°C for an extended
period can result in device failure. To ensure proper operation,
it is necessary to observe the maximum power derating as
determined by the coefficients in Table 3.
−40°C to +85°C
150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 5 of 24
AD8190
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
AVCC
1
2
3
4
5
6
7
8
9
PIN 1
INDICATOR
42 AVCC
_
_
IN A0
41 IP B3
_
_
IP A0
40 IN B3
AVEE
39 AVEE
_
_
IN A1
38 IP B2
_
_
AD8190
IP A1
37 IN B2
VTTI
36 VTTI
TOP VIEW
_
_
IN A2
35 IP B1
(Not to Scale)
_
_
IP A2
34 IN B1
AVCC 10
33 AVCC
_
_
IN A3 11
32 IP B0
_
_
IP A3 12
31 IN B0
AVEE 13
30 AVEE
_
_
29 I2C SDA
I2C ADDR 14
NOTES
1. THE AD8190 LFCSP HAS AN EXPOSED PADDLE (ePAD) ON THE UNDERSIDE
OF THE PACKAGE WHICH AIDS IN HEAT DISSIPATION. THE ePAD MUST BE
ELECTRICALLY CONNECTED TO THE AVEE SUPPLY PLANE IN ORDER TO
MEET THERMAL SPECIFICATIONS.
Figure 3. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
Mnemonic
AVCC
IN_A0
IP_A0
AVEE
Type1
Power
HS I
Description
1, 10, 33, 42
Positive Analog Supply. 3.3 V nominal.
High Speed Input Complement.
High Speed Input.
2
3
HS I
4, 13, 30, 39, ePAD
Power
HS I
Negative Analog Supply. 0 V nominal.
High Speed Input Complement.
High Speed Input.
5
IN_A1
IP_A1
VTTI
6
HS I
7, 36
8
Power
HS I
Input Termination Supply. Nominally connected to AVCC.
High Speed Input Complement.
High Speed Input.
IN_A2
IP_A2
IN_A3
IP_A3
I2C_ADDR
DVCC
ON0
9
HS I
11
12
14
15, 21
16
17
18, 24
19
20
22
23
25
26
27
28
29
31
32
HS I
High Speed Input Complement.
High Speed Input.
I2C Address LSB.
HS I
Control
Power
HS O
HS O
Power
HS O
HS O
HS O
HS O
HS O
HS O
Control
Control
Control
HS I
Positive Digital Power Supply. 3.3 V nominal.
High Speed Output Complement.
High Speed Output.
OP0
VTTO
ON1
Output Termination Supply. Nominally connected to AVCC.
High Speed Output Complement.
High Speed Output.
OP1
ON2
High Speed Output Complement.
High Speed Output.
OP2
ON3
High Speed Output Complement.
High Speed Output.
OP3
E
RESET
Configuration Registers Reset. This pin is normally pulled up to DVCC.
I2C Clock.
I2C Data.
A
EA
I2C_SCL
I2C_SDA
IN_B0
High Speed Input Complement.
High Speed Input.
IP_B0
HS I
Rev. 0 | Page 6 of 24
AD8190
Pin No.
34
35
37
38
40
41
43
44
45
46
47
48
49
50
51
52
53
54
55
56
Mnemonic
IN_B1
Type1
HS I
Description
High Speed Input Complement.
High Speed Input.
IP_B1
HS I
IN_B2
HS I
High Speed Input Complement.
High Speed Input.
IP_B2
HS I
IN_B3
HS I
High Speed Input Complement.
High Speed Input.
IP_B3
HS I
AUX_B3
AUX_B2
AUX_B1
AUX_B0
AMUXVCC
AUX_COM3
AUX_COM2
AUX_COM1
AUX_COM0
DVEE
LS I/O
LS I/O
LS I/O
LS I/O
Power
LS I/O
LS I/O
LS I/O
LS I/O
Power
LS I/O
LS I/O
LS I/O
LS I/O
Low Speed Input/Output.
Low Speed Input/Output.
Low Speed Input/Output.
Low Speed Input/Output.
Positive Auxiliary Switch Supply. 5 V typical.
Low Speed Common Input/Output.
Low Speed Common Input/Output.
Low Speed Common Input/Output.
Low Speed Common Input/Output.
Negative Digital and Auxiliary Switch Power Supply. 0 V nominal.
Low Speed Input/Output.
AUX_A3
AUX_A2
AUX_A1
AUX_A0
Low Speed Input/Output.
Low Speed Input/Output.
Low Speed Input/Output.
1 HS = high speed, LS = low speed, I = input, O = output.
Rev. 0 | Page 7 of 24
AD8190
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 27°C, AVCC = 3.3 V, VTTI = 3.3 V, VTTO = 3.3 V, DVCC = 3.3 V, AMUXVCC = 5 V, AVEE = 0 V, DVEE = 0 V, differential input swing =
1000 mV, TMDS outputs terminated with external 50 Ω resistors to 3.3 V, pattern = PRBS 27 − 1, data rate = 1.65 Gbps, unless otherwise noted.
HDMI CABLE
AD8190
DIGITAL
PATTERN
GENERATOR
SERIAL DATA
ANALYZER
EVALUATION
BOARD
SMA COAX CABLE
REFERENCE EYE DIAGRAM AT TP1
TP1
TP2
TP3
Figure 4. Test Circuit Diagram for RX Eye Diagrams
0.125UI/DIV AT 1.65Gbps
0.125UI/DIV AT 1.65Gbps
Figure 5. RX Eye Diagram at TP2 (Cable = 2 m, 30 AWG)
Figure 7. RX Eye Diagram at TP3, EQ = 6 dB (Cable = 2 m, 30 AWG)
0.125UI/DIV AT 1.65Gbps
0.125UI/DIV AT 1.65Gbps
Figure 6. RX Eye Diagram at TP2 (Cable = 20 m, 24 AWG)
Figure 8. RX Eye Diagram at TP3, EQ = 12 dB (Cable = 20 m, 24 AWG)
Rev. 0 | Page 8 of 24
AD8190
TA = 27°C, AVCC = 3.3 V, VTTI = 3.3 V, VTTO = 3.3 V, DVCC = 3.3 V, AMUXVCC = 5 V, AVEE = 0 V, DVEE = 0 V, differential input swing =
1000 mV, TMDS outputs terminated with external 50 Ω resistors to 3.3 V, pattern = PRBS 27 − 1, data rate = 1.65 Gbps, unless otherwise noted.
HDMI CABLE
AD8190
SERIAL DATA
ANALYZER
DIGITAL
PATTERN
GENERATOR
EVALUATION
BOARD
SMA COAX CABLE
REFERENCE EYE DIAGRAM AT TP1
TP1
TP2
TP3
Figure 9. Test Circuit Diagram for TX Eye Diagram
0.125UI/DIV AT 1.65Gbps
0.125UI/DIV AT 1.65Gbps
Figure 10. TX Eye Diagram at TP2, PE = 2 dB
Figure 12. TX Eye Diagram at TP3, PE = 2 dB (Cable = 2 m, 30 AWG)
0.125UI/DIV AT 1.65Gbps
0.125UI/DIV AT 1.65Gbps
Figure 11. TX Eye Diagram at TP2, PE = 6 dB
Figure 13. TX Eye Diagram at TP3, PE = 6 dB (Cable = 10 m, 28 AWG)
Rev. 0 | Page 9 of 24
AD8190
TA = 27°C, AVCC = 3.3 V, VTTI = 3.3 V, VTTO = 3.3 V, DVCC = 3.3 V, AMUXVCC = 5 V, AVEE = 0 V, DVEE = 0 V, differential input swing =
1000 mV, TMDS outputs terminated with external 50 Ω resistors to 3.3 V, pattern = PRBS 27 − 1, data rate = 1.65 Gbps, unless otherwise noted.
0.6
0.5
0.4
0.3
0.2
0.1
0
0.6
0.5
0.4
0.3
0.2
0.1
0
2m CABLE = 30AWG
2m CABLE = 30AWG
5m TO 10m CABLES = 28AWG
15m TO 20m CABLES = 24AWG
5m TO 10m CABLES = 28AWG
15m TO 30m CABLES = 24AWG
720p,
EQ = 12dB
720p, PE OFF
1080p, PE OFF
1080p,
EQ = 12dB
1080p, MAX PE
480p, PE OFF
1.65Gbps,
EQ = 12dB
720p, MAX PE
480p,
EQ = 12dB
480p, MAX PE
20
0
5
10
15
20
25
30
35
0
5
10
15
25
HDMI CABLE LENGTH (m)
HDMI CABLE LENGTH (m)
Figure 14. Jitter vs. Input Cable Length (See Figure 4 for Test Setup)
Figure 17. Jitter vs. Output Cable Length (See Figure 9 for Test Setup)
50
45
40
35
30
1200
1000
800
600
400
200
0
1.65Gbps
DJ (p-p)
25
20
15
10
5
1080i/720p
1080p
480p
480i
RJ (rms)
0
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
DATA RATE (Gbps)
DATA RATE (Gbps)
Figure 15. Jitter vs. Data Rate
Figure 18. Eye Height vs. Data Rate
50
45
40
35
30
25
20
15
10
5
800
700
600
500
400
300
200
100
0
DJ (p-p)
RJ (rms)
0
3.0
3.1
3.2
3.3
3.4
3.5
3.6
2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
Figure 16. Jitter vs. Supply Voltage
Figure 19. Eye Height vs. Supply Voltage
Rev. 0 | Page 10 of 24
AD8190
TA = 27°C, AVCC = 3.3 V, VTTI = 3.3 V, VTTO = 3.3 V, DVCC = 3.3 V, AMUXVCC = 5 V, AVEE = 0 V, DVEE = 0 V, differential input swing =
1000 mV, TMDS outputs terminated with external 50 Ω resistors to 3.3 V, pattern = PRBS 27 − 1, data rate = 1.65 Gbps, unless otherwise noted.
50
40
30
20
10
0
50
40
30
20
10
0
DJ (p-p)
DJ (p-p)
RJ (rms)
3.5
RJ (rms)
1.0
0
0.2
0.4
0.6
0.8
1.2
1.4
1.6
1.8
2.0
100
100
2.5
2.7
2.9
3.1
3.3
3.7
DIFFERENTIAL INPUT SWING (V)
INPUT COMMON-MODE VOLTAGE (V)
Figure 20. Jitter vs. Differential Input Swing
Figure 23. Jitter vs. Input Common-Mode Voltage
50
40
30
20
10
0
120
115
110
105
100
95
DJ (p-p)
RJ (rms)
90
85
80
–40
–60
–40
–20
0
20
40
60
80
–20
0
20
40
60
80
100
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 21. Jitter vs. Temperature
Figure 24. Differential Input Termination Resistance vs. Temperature
160
140
120
100
80
FALL TIME
RISE TIME
60
40
20
0
–40
–20
0
20
40
60
80
TEMPERATURE (°C)
Figure 22. Rise and Fall Time vs. Temperature
Rev. 0 | Page 11 of 24
AD8190
THEORY OF OPERATION
INTRODUCTION
VTTI
The primary function of the AD8190 is to switch one of two
(DVI or HDMI) single-link sources to one output. Each
HDMI/DVI link consists of four differential, high speed
channels and four auxiliary single-ended, low speed control
signals. The high speed channels include a data-word clock and
three transition minimized differential signaling (TMDS) data
channels running at 10× the data-word clock frequency for data
rates up to 1.65 Gbps. The four low speed control signals are
5 V tolerant bidirectional lines that can carry configuration
signals, HDCP encryption, and other information, depending
upon the specific application.
50Ω
50Ω
IP_xx
IN_xx
CABLE
EQ
AVEE
Figure 25. High Speed Input Simplified Schematic
OUTPUT CHANNELS
Each high speed output differential pair is terminated to the
3.3 V VTTO power supply through two single-ended 50 Ω
on-chip resistors (see Figure 26). This output termination is
user-selectable; all the output terminations can be turned on
or off by programming the TX_PTO bit of the transmitter
settings register.
All four high speed TMDS channels are identical; that is, the
pixel clock can be run on any of the four TMDS channels.
Transmit and receive channel compensation is provided for the
high speed channels where the user can (manually) select
among a number of fixed settings.
VTTO
The AD8190 has I2C serial programming with two user pro-
grammable I2C slave addresses. The I2C slave address of the
AD8190 is 0b100100X. The least significant bit, represented by
X in the address, is set by tying the I2C_ADDR pin to either
3.3 V (for the value, X = 1) or to 0 V (for X = 0).
50Ω
50Ω
OPx
ONx
DISABLE
AVEE
I
OUT
INPUT CHANNELS
Each high speed input differential pair terminates to the
Figure 26. High Speed Output Simplified Schematic
3.3 V VTTI power supply through a pair of single-ended 50 Ω
on-chip resistors, as shown in Figure 25. The input terminations
can be optionally disconnected for approximately 100 ms following
a source switch. The user can program which of the eight high
speed input channels employs this feature by selectively setting the
associated RX_PT bits in the input termination pulse register.
Additionally, all the input terminations can be disconnected by
programming the RX_TO bit in the receiver settings register.
The AD8190 output has a disable feature that places the outputs
in a tristate mode. This mode is enabled by setting the HS_EN
bit of the high speed device modes register. Larger wire-OR’ed
arrays can be constructed using the AD8190 in this mode.
The AD8190 requires output termination resistors when the
high speed outputs are enabled. Termination can be internal
and/or external. The internal terminations of the AD8190 are
enabled by setting the TX_PTO bit of the transmitter settings
register (the default upon reset). External terminations can be
provided either by on-board resistors or by the input termination
resistors of an HDMI/DVI receiver. If both internal and external
terminations are provided, set the output current level to 20 mA
by programming the TX_OCL bit of the transmitter settings
register (the default upon reset). If only external terminations
are provided, set the output current level to 10 mA. The high
speed outputs must be disabled if there are no output termination
resistors present in the system.
The input equalizer can be manually configured to provide two
different levels of high frequency boost: 6 dB or 12 dB. The user
can individually program the equalization level of the eight high
speed input channels by selectively setting the associated RX_EQ
bits in the receive equalizer register. No specific cable length is
suggested for a particular equalization setting because cable
performance varies widely between manufacturers; however, in
general, the equalization of the AD8190 can be set to 12 dB
without degrading the signal integrity, even for short input
cables. At the 12 dB setting, the AD8190 can equalize up to
20 meters of 24 AWG cable at 1080p, over reference cables that
exhibit an insertion loss of −15 dB.
The output pre-emphasis can be manually configured to provide
one of four different levels of high frequency boost. The specific
boost level is selected by programming the TX_PE bits of the
transmitter settings register. No specific cable length is suggested
for a particular pre-emphasis setting because cable performance
varies widely between manufacturers.
Rev. 0 | Page 12 of 24
AD8190
information to sources to optimize display use. EDID devices
may need to be available via the DDC bus, regardless of the
state of the AD8190 and any downstream circuit. For this
configuration, the auxiliary inputs of the powered down
AD8190 need to be in a high impedance state to avoid pulling
down on the DDC lines and preventing these other devices
from using the bus.
SWITCHING MODE
The AD8190 behaves like a 2:1 HDMI/DVI switch by imple-
menting a quad switching mode. In this mode, the user selects
the high speed source (A or B) that is routed to the output by
programming the HS_CH bit of the high speeds modes register
as shown in Table 7. The low speed auxiliary source (AUX_A or
AUX_B) that is routed to the common output is separately set
by programming the AUX_CH bit of the auxiliary device
register as shown in Table 9.
When the AD8190 is powered from a simple resistor network,
as shown in Figure 28, it uses the 5 V supply that is required
from any HDMI/DVI source to guarantee high impedance of
the auxiliary multiplexer pins. The AMUXVCC supply does not
draw any static current; therefore, it is recommended that the
resistor network tap the 5 V supplies as close to the connectors
as possible to avoid any additional voltage drop.
AUXILIARY LINES SWITCHING
The auxiliary (low speed) lines have no amplification. They are
routed using a passive switch that is bandwidth compatible with
standard speed I2C. The schematic equivalent for this passive
connection is shown in Figure 27.
This precaution does not need to be taken if the DDC
peripheral circuitry is connected to the bus downstream of
the AD8190.
R
AUX
AUX_A0
½C
AUX_COM0
½C
AUX
AUX
PIN 18 HDMI CONNECTOR
PIN 14 DVI CONNECTOR
Figure 27. Auxiliary Channel Simplified Schematic
Showing AUX_A0 to AUX_COM0 Routing
10kΩ
10MΩ
+5V INTERNAL
(IF ANY)
SOURCE A +5V
I < 50mA
When turning off the AD8190, care needs to be taken with
the AMUXVCC supply to ensure that the auxiliary multiplexer
pins are in a high impedance state. A scenario that illustrates
this requirement is one where the auxiliary multiplexer is used
to switch the display data channel (DDC) bus. In some applica-
tions, additional devices can be connected to the DDC bus
(such as an EEPROM with EDID information) upstream of the
AD8190. Extended display identification data (EDID) is a VESA
standard-defined data format for conveying display configuration
PERIPHERAL
CIRCUITRY
AD8190
AMUXVCC
PERIPHERAL
CIRCUITRY
I < 50mA
10kΩ
SOURCE B +5V
PIN 18 HDMI CONNECTOR
PIN 14 DVI CONNECTOR
Figure 28. Suggested AMUXVCC Power Scheme
Rev. 0 | Page 13 of 24
AD8190
SERIAL CONTROL INTERFACE
RESET
6. Wait for the AD8190 to acknowledge the request.
On initial power-up, or at any point in operation, the AD8190
register set can be restored to the default values by pulling the
7. Send the data (eight bits) to be written to the register
whose address was set in Step 5. This transfer should be
MSB first.
RESET
pin to low according to the specification in Table 1.
RESET
During normal operation, however, the
pin must be
8. Wait for the AD8190 to acknowledge the request.
9. Do one of the following:
RESET
pulled up to 3.3 V. Pulling the
pin to low sets the
HS_CH register to 0 (Input A) and incurs the associated
switching delay before the input can be switched to Input B,
regardless of the previous state of the AD8190.
a. Send a stop condition (while holding the I2C_SCL
line high, pull the I2C_SDA line high) and release
control of the bus to end the transaction (shown in
Figure 29).
WRITE PROCEDURE
To write data to the AD8190 register set, an I2C master (such as
a microcontroller) needs to send the appropriate control signals
to the AD8190 slave device. The signals are controlled by the
I2C master unless otherwise specified. For a diagram of the
procedure, see Figure 29. The steps for a write procedure are as
follows:
b. Send a repeated start condition (while holding the
I2C_SCL line high, pull the I2C_SDA line low) and
continue with Step 2 in this procedure to perform
another write.
c. Send a repeated start condition (while holding the
I2C_SCL line high, pull the I2C_SDA line low) and
continue with Step 2 of the read procedure (in the
Read Procedure section) to perform a read from
another address.
1. Send a start condition (while holding the I2C_SCL line
high, pull the I2C_SDA line low).
2. Send the AD8190 part address (seven bits). The upper six
bits of the AD8190 part address are the static value
[100100] and the LSB is set by Input Pin I2C_ADDR. This
transfer should be MSB first.
d. Send a repeated start condition (while holding the
I2C_SCL line high, pull the I2C_SDA line low) and
continue with Step 8 of the read procedure (in the
Read Procedure section) to perform a read from the
same address set in Step 5.
3. Send the write indicator bit (0).
4. Wait for the AD8190 to acknowledge the request.
5. Send the register address (eight bits) to which data is to be
written. This transfer should be MSB first.
*
I2C_SCL
R/W
GENERAL CASE
START
FIXED ADDR PART
REGISTER ADDR
DATA
STOP
I2C_SDA
ADDR
ACK
ACK
ACK
EXAMPLE
I2C_SDA
1
2
3
4
5
6
7
8
9
*THE SWITCHING/UPDATE DELAY BEGINS AT THE FALLING EDGE OF THE
LAST DATA BIT; FOR EXAMPLE, THE FALLING EDGE JUST BEFORE STEP 8.
Figure 29. I2C Write Procedure
Rev. 0 | Page 14 of 24
AD8190
I2C_SCL
R/W
R/W
GENERAL CASE
I2C_SDA
START
FIXED PART ADDR
REGISTER ADDR
SR
FIXED PART ADDR
DATA
STOP
ADDR ACK
ACK
ADDR ACK
ACK
EXAMPLE
I2C_SDA
1
2
3
4
5
6
7
8
9
10 11
12
13
Figure 30. I2C Read Procedure
13. Do one of the following:
READ PROCEDURE
To read data from the AD8190 register set, an I2C master (such
as a microcontroller) needs to send the appropriate control
signals to the AD8190 slave device. The signals are controlled
by the I2C master unless otherwise specified. For a diagram of
the procedure, see Figure 30. The steps for a read procedure are
as follows:
a. Send a stop condition (while holding the I2C_SCL
line high, pull the SDA line high) and release control
of the bus to end the transaction (shown in Figure 30).
b. Send a repeated start condition (while holding the
I2C_SCL line high, pull the I2C_SDA line low) and
continue with Step 2 of the write procedure (see the
previous Write Procedure section) to perform a write.
1. Send a start condition (while holding the I2C_SCL line
high, pull the I2C_SDA line low).
c. Send a repeated start condition (while holding the
I2C_SCL line high, pull the I2C_SDA line low) and
continue with Step 2 of this procedure to perform a
read from another address.
2. Send the AD8190 part address (seven bits). The upper six
bits of the AD8190 part address are the static value
[100100] and the LSB is set by Input Pin I2C_ADDR. This
transfer should be MSB first.
d. Send a repeated start condition (while holding the
I2C_SCL line high, pull the I2C_SDA line low) and
continue with Step 8 of this procedure to perform a
read from the same address.
3. Send the write indicator bit (0).
4. Wait for the AD8190 to acknowledge the request.
5. Send the register address (eight bits) from which data is to
be read. This transfer should be MSB first.
SWITCHING/UPDATE DELAY
There is a delay between when a user writes to the configura-
tion registers of the AD8190 and when that state change takes
physical effect. This update delay begins at the falling edge of
I2C_SCL for the last data bit transferred, as shown in Figure 29.
This update delay is register specific and the times are specified
in Table 1.
6. Wait for the AD8190 to acknowledge the request.
7. Send a repeated start condition (Sr) by holding the
I2C_SCL line high and pulling the I2C_SDA line low.
8. Resend the AD8190 part address (seven bits) from Step 2.
The upper six bits of the AD8190 part address compose the
static value [100100]. The LSB is set by Input Pin I2C_ADDR.
This transfer should be MSB first.
During a delay window, new values can be written to the
configuration registers but the AD8190 does not physically
update until the end of that register’s delay window. Writing
new values during the delay window does not reset the window;
new values supersede the previously written values. At the end
of the delay window, the AD8190 physically assumes the state
indicated by the last set of values written to the configuration
registers. If the configuration registers are written after the delay
window ends, the AD8190 immediately updates and a new
delay window begins.
9. Send the read indicator bit (1).
10. Wait for the AD8190 to acknowledge the request.
11. The AD8190 serially transfers the data (eight bits) held in
the register indicated by the address set in Step 5. This data
is sent MSB first.
12. Acknowledge the data from the AD8190.
Rev. 0 | Page 15 of 24
AD8190
CONFIGURATION REGISTERS
The serial interface configuration registers can be read and written using the I2C serial interface, Pin I2C_SDA, and Pin I2C_SCL.
The LSB of the AD8190 I2C part address is set by tying Pin I2C_ADDR to 3.3 V (I2C_ADDR = 1) or 0 V (I2C_ADDR = 0).
Table 5. Register Map
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Addr. Default
High Speed
Device
High speed
switch enable
High speed
source select
0x00
0x40
Modes
HS_EN
HS_CH
Auxiliary
Device
Modes
Auxiliary
switch enable
Auxiliary
switch
source select
0x01
0x40
AUX_EN
AUX_CH
Receiver
Settings
High speed
input
termination
select
0x10
0x11
0x01
0x00
RX_TO
Input
Input termination pulse-on-source-switch select (disconnect termination for a short period of time)
Termination
Pulse
RX_PT[7] RX_PT[6]
RX_PT[5] RX_PT[4] RX_PT[3] RX_PT[2] RX_PT[1]
RX_PT [0]
Receive
Equalizer
Input equalization level select
0x13
0x20
0x00
0x03
RX_EQ[7] RX_EQ[6]
RX_EQ[5] RX_EQ[4] RX_EQ[3] RX_EQ[2] RX_EQ[1]
RX_EQ[0]
Transmitter
Settings
High speed output
pre-emphasis level
select
High speed High speed
output output
termination current level
select
select
TX_PE[1] TX_PE[0] TX_PTO
TX_OCL
AUXILIARY DEVICE MODES REGISTER
HIGH SPEED DEVICE MODES REGISTER
AUX_EN: Auxiliary (Low Speed) Switch Enable Bit
Table 8. AUX_EN Description
HS_EN: High Speed (TMDS) Switch Enable Bit
Table 6. HS_EN Description
AUX_EN Description
HS_EN Description
0
Auxiliary switch off, no low speed input/output to
low speed common input/output connection
Auxiliary switch on
0
1
High speed channels off, low power/standby mode
High speed channels on
1
HS_CH: High Speed (TMDS) Source Select Bit
Table 7. HS_CH Mapping
AUX_CH: Auxiliary (Low Speed) Switch Source Select Bit
Table 9. AUX_CH Mapping
HS_CH O[3:0]
Description
AUX_CH AUX_COM[3:0]
Description
0
1
A[3:0]
B[3:0]
High speed Source A switched to output
High speed Source B switched to output
0
AUX_A[3:0]
Auxiliary Source A switched to
output
1
AUX_B[3:0]
Auxiliary Source B switched to
output
Rev. 0 | Page 16 of 24
AD8190
RECEIVER SETTINGS REGISTER
RECEIVE EQUALIZER REGISTER
RX_TO: High Speed (TMDS) Input Termination On/Off
Select Bit
Table 10. RX_TO Description
RX_EQ[X]: High Speed (TMDS) Input X Equalization Level
Select Bit
Table 13. RX_EQ[X] Description
RX_TO
Description
RX_EQ[X]
Description
0
1
Input termination off
0
1
Low equalization (6 dB)
High equalization (12 dB)
Input termination on (can be pulsed on and off
when source is switched, according to settings in
the input termination pulse register)
Table 14. RX_EQ[X] Mapping
RX_EQ[X]
Corresponding Input TMDS Channel
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
A0
A1
A2
A3
B3
B2
B1
B0
INPUT TERMINATION PULSE REGISTER
RX_PT[X]: High Speed (TMDS) Input Termination X
Pulse-On-Source Switch Select Bit
Table 11. RX_PT[X] Description
RX_PT[X] Description
0
Input termination for TMDS Channel X always
connected when source is switched
1
Input termination for TMDS Channel X
disconnected for approximately 100 ms when
source is switched
TRANSMITTER SETTINGS REGISTER
TX_PE[1:0]: High Speed (TMDS) Output Pre-Emphasis
Level Select Bus (All TMDS Channels)
Table 15. TX_PE[1:0] Description
Table 12. RX_PT[X] Mapping
RX_PT[X] Corresponding Input TMDS Channel
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
A0
A1
A2
A3
B3
B2
B1
B0
TX_PE[1:0]
Description
00
01
10
11
No pre-emphasis (0 dB)
Low pre-emphasis (2 dB)
Medium pre-emphasis (4 dB)
High pre-emphasis (6 dB)
X_PTO: High Speed (TMDS) Output Termination On/Off
Select Bit (All Channels)
Table 16. TX_PTO Description
TX_PTO
Description
0
1
Output termination off
Output termination on
TX_OCL: High Speed (TMDS) Output Current Level Select
Bit (All Channels)
Table 17. TX_OCL Description
TX_OCL
Description
0
1
Output current set to 10 mA
Output current set to 20 mA
Rev. 0 | Page 17 of 24
AD8190
APPLICATION NOTES
Figure 31. Evaluation Board Layout of the TMDS Traces
Although inverting the output pin order of the AD8190 on the
PCB requires a designer to place vias in the high speed signal
path, the AD8190 fully buffers and electrically decouples the
outputs from the inputs. Therefore, the effects of the vias placed
on the output signal lines are not seen at the input of the AD8190.
The programmable output terminations also improve signal
quality at the output of the AD8190. The PCB designer, there-
fore, has significantly improved flexibility in the placement and
routing of the output signal path with the AD8190 over other
solutions.
The AD8190 is an HDMI/DVI switch featuring equalized
TMDS inputs and pre-emphasized TMDS outputs. It is in-
tended for use as a 2:1 switch in systems with long cable runs
on both the input and/or the output, and is fully HDMI 1.2a
receive compliant.
PINOUT
The AD8190 was designed to have an HDMI/DVI receiver
pinout at its input and a transmitter pinout at its output. This
makes the AD8190 ideal for use in AVR-type applications
where a designer routes both the inputs and the outputs directly
to HDMI/DVI connectors as shown in Figure 31. When the
AD8190 is used in receiver-type applications, it is necessary to
change the ordering of the output pins on the PCB to match up
with the on-board receiver, as shown in Figure 32.
An example of high speed routing from an HDMI Standard
Revision 1.2a receive-compliant reference design is shown in
Figure 32. The light gray TMDS lines are routed on the top layer
of the PCB, the dark gray TMDS lines are routed on the bottom
layer, and the black dots are vias.
One advantage of the AD8190 in an AVR-type application is
that all of the high speed signals can be routed on one side (the
topside) of the board, as shown in Figure 31. In addition to
12 dB of input equalization, the AD8190 provides up to 6 dB of
output pre-emphasis that boosts the output TMDS signals and
allows the AD8190 to precompensate when driving long PCB
traces or output cables. The net effect of the input equalization
and output pre-emphasis of the AD8190 is that the AD8190 can
compensate for the signal degradation of both input and output
cables; it acts to reopen a closed input data eye and transmit a
full-swing HDMI signal to an end receiver. More information
on the specific performance metrics of the AD8190 can be
found in the Typical Performance Characteristics section.
HDMI IN
J4
AD9880 (Rx)
HDMI IN
AD8190
Figure 32. Layout of the TMDS Traces for the AD8190 in an HDMI Standard
Revision 1.2a Receive-Compliant Reference Design
The AD8190 also provides a distinct advantage in receive-type
applications because it is a fully buffered HDMI/DVI switch.
Rev. 0 | Page 18 of 24
AD8190
terminations on-chip for both its inputs and outputs, and both
the input and output terminations can be enabled or disabled
through the serial interface. Transmitter termination is not fully
specified by the HDMI standard but its inclusion improves the
overall system signal integrity.
CABLE LENGTHS AND EQUALIZATION
The AD8190 offers two levels of programmable equalization
for the high speed inputs: 6 dB and 12 dB. The equalizer of
the AD8190 is optimized for video data rates of 1.65 Gbps,
and as shown in Figure 14, it can equalize up to 20 meters of
24 AWG HDMI cable at data rates corresponding to the video
format, 1080p.
The audiovisual (AV) data carried on these high speed channels
is encoded by a technique called transition minimized differ-
ential signaling (TMDS) and in the case of HDMI, is also encrypted
according to the high bandwidth digital copy protection (HDCP)
standard.
The length of cable that can be used in a typical HDMI/DVI
application depends on a large number of factors including:
•
Cable quality: the quality of the cable in terms of conductor
wire gauge and shielding. Thicker conductors have lower
signal degradation per unit length.
The second group of signals consists of low speed auxiliary
control signals used for communication between a source and a
sink. Depending upon the application, these signals can include
the DDC bus (this is an I2C bus used to send EDID information
and HDCP encryption keys between the source and the sink),
the consumer electronics control (CEC) line, and the hot plug
detect (HPD) line. These auxiliary signals are bidirectional, low
speed, and transferred over a single-ended transmission line
that does not need to have controlled impedance. The primary
concern with laying out the auxiliary lines is ensuring that they
conform to the I2C bus standard and do not have excessive
capacitive loading.
•
•
Data rate: the data rate being sent over the cable. The signal
degradation of HDMI cables increases with data rate.
Edge rates: the edge rates of the source input. Slower input
edges result in more significant data eye closure at the end
of a cable.
•
Receiver sensitivity: the sensitivity of the terminating
receiver.
As such, specific cable types and lengths are not recom-
mended for use with a particular equalizer setting. In
nearly all applications, the AD8190 equalization level can
be set to high, or 12 dB, for all input cable configurations
at all data rates, without degrading the signal integrity.
TMDS Signals
In the HDMI/DVI standard, four differential pairs carry the
TMDS signals. In DVI, three of these pairs are dedicated to
carrying RGB video and sync data. For HDMI, audio data is
also interleaved with the video data; the DVI standard does
not incorporate audio information. The fourth high speed
differential pair is used for the AV data-word clock, and runs
at one-tenth the speed of the TMDS data channels.
THE AD8190 AS A SINGLE-CHANNEL BUFFER
The AD8190 can be used as a single-channel TMDS buffer
without the need for any external I2C control. In its default
configuration, the AD8190 connects both the high speed and
low speed channels of Input A to their respective outputs, sets
the input equalization level to 6 dB, the output pre-emphasis
level to 0 dB, enables both the output and input terminations,
and provides a fully functioning HDMI link with TMDS
buffering.
The four high speed channels of the AD8190 are identical.
No concession was made to lower the bandwidth of the fourth
channel for the pixel clock, so any channel can be used for any
TMDS signal. The user chooses which signal is routed over
which channel. Additionally, the TMDS channels are symmetrical;
therefore, the p and n of a given differential pair are inter-
changeable, provided the inversion is consistent across all inputs
and outputs of the AD8190. However, the routing between
inputs and outputs through the AD8190 is fixed. For example,
Output Channel 0 always switches between Input A0 and
Input B0, and so forth.
RESET
The AD8190 enters this default state whenever the
is pulled to low in accordance with the specification in Table 1.
pin
PCB LAYOUT GUIDELINES
The AD8190 is used to switch two distinctly different types of
signals, both of which are required for HDMI and DVI video.
These signal groups require different treatment when laying out
a PC board.
The AD8190 buffers the TMDS signals and the input traces can
be considered electrically independent of the output traces. In
most applications, the quality of the signal on the input TMDS
traces are more sensitive to the PCB layout. Regardless of the
data being carried on a specific TMDS channel, or whether the
TMDS line is at the input or the output of the AD8190, all four
high speed signals should be routed on a PCB in accordance
with the same RF layout guidelines.
The first group of signals carries the audiovisual (AV) data.
HDMI/DVI video signals are differential, unidirectional, and
high speed (up to 1.65 Gbps). The channels that carry the video
data must be controlled impedance, terminated at the receiver,
and capable of operating up to at least 1.65 Gbps. It is especially
important to note that the differential traces that carry the
TMDS signals should be designed with a controlled differential
impedance of 100 Ω. The AD8190 provides single-ended 50 Ω
Rev. 0 | Page 19 of 24
AD8190
There are many combinations that can produce the correct
characteristic impedance. It is generally required to work with
the PC board fabricator to obtain a set of parameters to produce
the desired results.
Layout for the TMDS Signals
The TMDS differential pairs can either be microstrip traces,
routed on the outer layer of a board, or stripline traces, routed
on an internal layer of the board. If microstrip traces are used,
there should be a continuous reference plane on the PCB layer
directly below the traces. If stripline traces are used, they must
be sandwiched between two continuous reference planes in the
PCB stack-up. Additionally, the p and n of each differential pair
must have a controlled differential impedance of 100 Ω. The
characteristic impedance of a differential pair is a function of
several variables including the trace width, the distance separating
the two traces, the spacing between the traces and the reference
plane, and the dielectric constant of the PC board binder material.
Interlayer vias introduce impedance discontinuities that can
cause reflections and jitter on the signal path, therefore, it is
preferable to route the TMDS lines exclusively on one layer of the
board, particularly for the input traces. Additionally, to prevent
unwanted signal coupling and interference, route the TMDS
signals away from other signals and noise sources on the PCB.
One consideration is how to guarantee a differential pair with a
differential impedance of 100 Ω over the entire length of the
trace. One technique to accomplish this is to change the width
of the traces in a differential pair based on how closely one trace
is coupled to the other. When the two traces of a differential
pair are close and strongly coupled, they should have a width
that produces a 100 Ω differential impedance. When the traces
split apart to go into a connector, for example, and are no longer
so strongly coupled, the width of the traces should be increased
to yield a differential impedance of 100 Ω in the new configuration.
TMDS Terminations
The AD8190 provides internal 50 Ω single-ended terminations
for all of its high speed inputs and outputs. It is not necessary to
include external termination resistors for the TMDS differential
pairs on the PCB.
Both traces of a given differential pair must be equal in length
to minimize intrapair skew. Maintaining the physical symmetry
of a differential pair is integral to ensuring its signal integrity;
excessive intrapair skew can introduce jitter through duty cycle
distortion (DCD). The p and n of a given differential pair should
always be routed together in order to establish the required 100 Ω
differential impedance. Enough space should be left between
the differential pairs of a given group so that the n of one pair
does not couple to the p of another pair. For example, one tech-
nique is to make the interpair distance 4 to 10 times wider than
the intrapair spacing.
The output termination resistors of the AD8190 back-terminate
the output TMDS transmission lines. These back-terminations
act to absorb reflections from impedance discontinuities on the
output traces, improving the signal integrity of the output traces
and adding flexibility to how the output traces can be routed.
For example, interlayer vias can be used to route the AD8190
TMDS outputs on multiple layers of the PCB without severely
degrading the quality of the output signal.
Auxiliary Control Signals
There are four single-ended control signals associated with each
source or sink in an HDMI/DVI application. These are hot plug
detect (HPD), consumer electronics control (CEC), and two
display data channel (DDC) lines. The two signals on the DDC
bus are SDA and SCL (serial data and serial clock, respectively).
These four signals can be switched through the auxiliary bus of
the AD8190 and do not need to be routed with the same strict
considerations as the high speed TMDS signals.
Any group of four TMDS channels (Input A, Input B, or the
output) should have closely matched trace lengths in order to
minimize interpair skew. Severe interpair skew can cause the
data on the four different channels of a group to arrive out of
alignment with one another. A good practice is to match the
trace lengths for a given group of four channels to within
0.05 inches on FR4 material.
The length of the TMDS traces should be minimized to re-
duce overall signal degradation. Commonly used PC board
material such as FR4 is lossy at high frequencies, so long traces
on the circuit board increase signal attenuation, resulting in
decreased signal swing and increased jitter through intersymbol
interference (ISI).
In general, it is sufficient to route each auxiliary signal as a
single-ended trace. These signals are not sensitive to impedance
discontinuities, do not require a reference plane, and can be
routed on multiple layers of the PCB. However, it is best to
follow strict layout practices whenever possible to prevent the
PCB design from affecting the overall application. The specific
routing of the HPD, CEC, and DDC lines depends upon the
application in which the AD8190 is being used.
Controlling the Characteristic Impedance of a TMDS
Differential Pair
The characteristic impedance of a differential pair depends on a
number of variables including the trace width, the distance
between the two traces, the height of the dielectric material
between the trace and the reference plane below it, and the
dielectric constant of the PCB binder material. To a lesser
extent, the characteristic impedance also depends upon the
trace thickness and the presence of solder mask.
For example, the maximum speed of signals present on the
auxiliary lines are 100 kHz I2C data on the DDC lines, therefore,
any layout that enables 100 kHz I2C to be passed over the DDC
bus should suffice. The HDMI 1.2a specification, however,
places a strict 50 pF limit on the amount of capacitance that can
be measured on either SDA or SCL at the HDMI input connector.
Rev. 0 | Page 20 of 24
AD8190
This 50 pF limit includes the HDMI connector, the PCB, and
whatever capacitance is seen at the input of the AD8190, or an
equivalent receiver. There is a similar limit of 100 pF of input
capacitance for the CEC line.
When the AD8190 is powered up, one set of the auxiliary inputs
is passively routed to the outputs. In this state, the AD8190
looks like a 100 Ω resistor between the selected auxiliary inputs
and the corresponding outputs as illustrated in Figure 27. The
AD8190 does not buffer the auxiliary signals, therefore, the
input traces, output traces, and the connection through the
AD8190 all must be considered when designing a PCB to meet
HDMI/DVI specifications. The unselected auxiliary inputs of the
AD8190 are placed into a high impedance mode when the device
is powered up. To ensure that all of the auxiliary inputs of the
AD8190 are in a high impedance mode when the device is
powered off, it is necessary to power the AMUXVCC supply as
illustrated in Figure 28.
The parasitic capacitance of traces on a PCB increases with
trace length. To help ensure that a design satisfies the HDMI
specification, the length of the CEC and DDC lines on the PCB
should be made as short as possible. Additionally, if there is a
reference plane in the layer adjacent to the auxiliary traces in
the PCB stackup, relieving or clearing out this reference plane
immediately under the auxiliary traces significantly decreases
the amount of parasitic trace capacitance. An example of the
board stackup is shown in Figure 33.
In contrast to the auxiliary signals, the AD8190 buffers the
TMDS signals, allowing a PCB designer to layout the TMDS
inputs independently of the outputs.
3W
W
3W
SILKSCREEN
Power Supplies
LAYER 1: MICROSTRIP
PCB DIELECTRIC
The AD8190 has five separate power supplies referenced to
two separate grounds. The supply/ground pairs are:
AVCC/AVEE, VTTI/AVEE, VTTO/AVEE, DVCC/DVEE,
and AMUXVCC/DVEE.
LAYER 2: REFERENCE PLANE
PCB DIELECTRIC
LAYER 3: REFERENCE PLANE
PCB DIELECTRIC
The AVCC/AVEE (3.3 V) and DVCC/DVEE (3.3 V) supplies
power the core of the AD8190. The VTTI/AVEE supply (3.3 V)
powers the input termination (see Figure 25). Similarly, the
VTTO/AVEE supply (3.3 V) powers the output termination
(see Figure 26). The AMUXVCC/DVEE supply (3.3 V to 5 V)
powers the auxiliary multiplexer core and determines the
maximum allowed voltage on the auxiliary lines. For example,
if the DDC bus is using 5 V I2C, then AMUXVCC should be
connected to +5 V relative to DVEE.
LAYER 4: MICROSTRIP
SILKSCREEN
REFERENCE LAYER
RELIEVED UNDERNEATH
MICROSTRIP
Figure 33. Example Board Stackup
HPD is a dc signal presented by a sink to a source to indicate
that the source EDID is available for reading. The placement of
this signal is not critical, but it should be routed as directly as
possible.
In a typical application, all pins labeled AVEE or DVEE should
be connected directly to ground. All pins labeled AVCC,
DVCC, VTTI, or VTTO should be connected to 3.3 V, and
Pin AMUXVCC tied to 5 V. The supplies can also be powered
individually, but care must be taken to ensure that each stage of
the AD8190 is powered correctly.
Rev. 0 | Page 21 of 24
AD8190
Power Supply Bypassing
supply planes and be placed within a few centimeters of the
AD8190. The AMUXVCC supply does not require additional
bypassing. This scheme is illustrated in Figure 35.
The AD8190 requires minimal supply bypassing. When
powering the supplies individually, place a 0.01 μF capacitor
between each 3.3 V supply pin (AVCC, DVCC, VTTI, and
VTTO) and ground to filter out supply noise. Generally, bypass
capacitors should be placed near the power pins and should
connect directly to the relevant supplies (without long inter-
vening traces). For example, to improve the parasitic inductance
of the power supply decoupling capacitors, minimize the trace
length between capacitor landing pads and the vias as shown in
Figure 34.
DECOUPLING
CAPACITORS
RECOMMENDED
AD8190
EXTRA ADDED INDUCTANCE
AUXILIARY LINES
TMDS TRACES
NOT RECOMMENDED
Figure 34. Recommended Pad Outline for Bypass Capacitors
In applications where the AD8190 is powered by a single 3.3 V
supply, it is recommended to use two reference supply planes
and bypass the 3.3 V reference plane to the ground reference
plane with one 220 pF, one 1000 pF, two 0.01 μF, and one 4.7 μF
capacitors. The capacitors should via down directly to the
Figure 35. Example Placement of Power Supply Decoupling Capacitors
Around the AD8190
Rev. 0 | Page 22 of 24
AD8190
OUTLINE DIMENSIONS
0.30
0.23
0.18
8.00
BSC SQ
0.60 MAX
0.60 MAX
PIN 1
INDICATOR
43
42
56
1
PIN 1
INDICATOR
4.95
4.80 SQ
4.65
TOP
VIEW
EXPOSED
7.75
BSC SQ
PAD
(BOTTOM VIEW)
0.50
0.40
0.30
14
15
29
28
0.30 MIN
6.50
REF
0.80 MAX
0.65 TYP
1.00
0.85
0.80
12° MAX
0.05 MAX
0.02 NOM
COPLANARITY
0.08
SEATING
PLANE
0.50 BSC
0.20 REF
COMPLIANT TO JEDEC STANDARDS MO-220-VLLD-2
NOTE:
THE AD8190 HAS A CONDUCTIVE HEAT SLUG TO HELP DISSIPATE HEAT AND ENSURE RELIABLE OPERATION OF
THE DEVICE OVER THE FULL DVI/HDMI TEMPERATURE RANGE. THE SLUG IS EXPOSED ON THE BOTTOM OF
THE PACKAGE AND ELECTRICALLY CONNECTED TO AVEE. IT IS RECOMMENDED THAT NO PCB SIGNAL
TRACES OR VIAS BE LOCATED UNDER THE PACKAGE THAT COULD COME IN CONTACT WITH THE CONDUCTIVE
SLUG. ATTACHING THE SLUG TO A AVEE PLANE WILL REDUCE THE JUNCTION TEMPERATURE OF THE
DEVICE WHICH MAY BE BENEFICIAL IN HIGH TEMPERATURE ENVIRONMENTS.
Figure 36. 56-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
8 mm × 8 mm Body, Very Thin Quad
(CP-56-3)
Dimensions shown in millimeters
ORDERING GUIDE
Temperature
Package
Option
Ordering
Quantity
Model
Range
Package Description
AD8190ACPZ1
AD8190ACPZ-R71
AD8190-EVAL
−40°C to +85°C
−40°C to +85°C
56-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
56-Lead Lead Frame Chip Scale Package [LFCSP_VQ], Reel CP-56-3
Evaluation Kit
CP-56-3
750
1 Z = Pb-free part.
Rev. 0 | Page 23 of 24
AD8190
NOTES
Purchase of licensed I2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips
I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06122-0-7/06(0)
Rev. 0 | Page 24 of 24
相关型号：
AD8191AASTZ
4-CHANNEL, AUDIO/VIDEO SWITCH, PQFP100, 14 X 14 MM, ROHS COMPLIANT, MS-026BED, LQFP-100
ROCHESTER
©2020 ICPDF网 联系我们和版权申明