AD8506ARMZ [ADI]

Micropower, Rail-to-Rail I/O, High Linearity Amplifiers; 微功耗,轨到轨输入/输出,高线性度放大器
AD8506ARMZ
型号: AD8506ARMZ
厂家: ADI    ADI
描述:

Micropower, Rail-to-Rail I/O, High Linearity Amplifiers
微功耗,轨到轨输入/输出,高线性度放大器

放大器 光电二极管
文件: 总10页 (文件大小:140K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
Micropower, Rail-to-Rail I/O,  
High Linearity Amplifiers  
Preliminary Technical Data  
AD8506  
FEATURES  
PIN CONFIGURATIONS  
High linearity  
BALL A1  
CORNER  
PSRR: 105dB minimum  
1
2
3
CMRR: 105 dB typical  
A
B
C
OUT  
-IN  
OUT  
Very low supply current: 20 μA/amp maximum  
1.8 V to 5.5 V single-supply operation  
Rail-to-rail input and output  
Low noise 2.9 μV p-p from 0.1 Hz to 10 Hz  
4 mV offset voltage maximum  
Very low input bias current: 1 pA typical  
V+  
-IN  
+IN  
+IN  
V-  
TOP VIEW  
(BALL SIDE DOWN)  
APPLICATIONS  
Figure 1. 8-Ball WLCSP  
Pressure and position sensors  
Remote security  
Medical monitors  
Battery-powered consumer equipment  
Hazard detectors  
1
8
OUT A  
-IN A  
V+  
GENERAL DESCRIPTION  
OUT B  
-IN B  
+IN B  
AD8506  
The AD8506 is a dual micro-power amplifier featuring  
rail-to-rail input and output swings while operating from  
a 1.8 V to 5.5 V single power supply.  
+IN A  
V-  
Employing a new circuit technology, these low cost amplifiers  
offer high linearity (excellent PSRR and CMRR performance)  
and very low bias current, while operating with a supply current  
of less than 20 μA per amplifier.  
Figure 2. 8-Lead MSOP (RM Suffix)  
This combination of features makes the AD8506 amplifier an  
ideal choice for battery-powered applications since it minimizes  
errors due to power supply voltage variations over the batterys  
lifetime and maintains relatively high CMRR for a rail-to-rail op  
amp.  
Remote battery-powered sensors, handheld instrumentation  
and consumer equipment, hazard detection (for example, smoke,  
fire, and gas), and patient monitors can benefit from the  
features of the AD8506 amplifier.  
The AD8506 is specified for both the industrial temperature  
range (−40°C to +85°C) and the extended industrial temperature  
range (−40°C to +125°C). AD8506 dual amplifiers are available  
in the standard 8-lead MSOP and WLCSP.  
Rev. PrA  
Information furnished by Analog Devices is believed to be accurate and reliable. However, no  
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other  
rights of third parties that may result from its use. Specifications subject to change without notice. No  
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.  
Trademarks and registeredtrademarks arethe property of their respective owners.  
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.  
Tel: 781.329.4700  
Fax: 781.461.3113  
www.analog.com  
©2007 Analog Devices, Inc. All rights reserved.  
AD8506  
Preliminary Technical Data  
TABLE OF CONTENTS  
Thermal Resistance.......................................................................5  
ESD Caution...................................................................................5  
Typical Performance Characteristics ..............................................6  
Terminology.......................................................................................7  
Theory of Operation .........................................................................8  
Applications Information.................................................................9  
Outline Dimensions....................................................................... 10  
Ordering Guide .......................................................................... 10  
Features .............................................................................................. 1  
Applications....................................................................................... 1  
General Description......................................................................... 1  
Pin Configurations ........................................................................... 1  
Revision History ............................................................................... 2  
Specifications..................................................................................... 3  
Electrical Characteristics – VS = 5V........................................... 3  
Electrical Characteristics – VS =1.8V ........................................ 4  
Absolute Maximum Ratings............................................................ 5  
REVISION HISTORY  
10/07—Revision 0: Initial Version  
Rev. PrA | Page 2 of 10  
Preliminary Technical Data  
AD8506  
SPECIFICATIONS  
ELECTRICAL CHARACTERISTICS – VS = 5V  
VS = 5 V, VCM = Vs/2, TA = 25°C, unless otherwise specified.  
Table 1.  
Parameter  
Symbol  
Conditions  
Min  
Typ  
1
Max  
Unit  
INPUT CHARACTERISTICS  
Offset Voltage  
Input Bias Current  
VOS  
IB  
0 V < VCM < 5 V  
4
mV  
pA  
pA  
pA  
pA  
pA  
pA  
V
dB  
dB  
dB  
dB  
10  
100  
600  
5
50  
100  
5
−40°C < TA < +85°C  
−40°C < TA < +125°C  
Input Offset Current  
IOS  
0.5  
−40°C < TA < +85°C  
−40°C < TA < +125°C  
−40°C < TA < +125°C  
VCM = 0 V to 5 V  
−40°C < TA < +85°C  
−40°C < TA < +125°C  
0.05 < VOUT < 4.95  
−40°C < TA < +85°C  
−40°C < TA < +125°C  
−40°C < TA < +85°C  
−40°C < TA < +125°C  
Input Voltage Range  
Common-Mode Rejection Ratio  
0
90  
90  
90  
110  
100  
100  
CMRR  
AVO  
105  
105  
Large Signal Voltage Gain  
Offset Voltage Drift  
130  
dB  
dB  
μV/°C  
μV/°C  
2.2  
2.2  
ΔVOS/ΔT  
OUTPUT CHARACTERISTICS  
Output Voltage High  
VOH  
VOL  
ISC  
RL = 100 kΩ to GND  
RL = 10 kΩ to GND  
RL = 100 kΩ to VS  
RL = 10 kΩ to VS  
4.95  
4.85  
4.99  
4.9  
2
V
V
Output Voltage Low  
Short Circuit Limit  
50  
150  
60  
80  
TBD  
mV  
mV  
mA  
mA  
mA  
8
−40°C to +85°C  
−40°C to +125°C  
POWER SUPPLY  
Power Supply Rejection Ratio  
PSRR  
ISY  
VS = 1.8 V to 5 V  
−40°C to +85°C  
−40°C to +125°C  
VO = VS /2  
105  
100  
90  
120  
120  
120  
18  
dB  
dB  
dB  
μA  
μA  
Supply Current/Amplifier  
20  
28  
−40°C < TA < +125°C  
DYNAMIC PERFORMANCE  
Slew Rate  
SR  
GBP  
12  
150  
mV/μs  
kHz  
Gain Bandwidth Product  
NOISE PERFORMANCE  
Peak-to-Peak Noise  
Voltage Noise Density  
Current Noise Density  
en p-p  
en  
in  
f = 0.1 to 10 Hz  
f = 1 kHz  
f = 10 Hz  
2.9  
48  
TBD  
μV p-p  
nV/√Hz  
fA/√Hz  
Rev. PrA | Page 3 of 10  
AD8506  
Preliminary Technical Data  
ELECTRICAL CHARACTERISTICS – VS =1.8V  
VS = 1.8 V, VCM = Vs/2, TA = 25°C, unless otherwise specified.  
Table 2.  
Parameter  
Symbol  
Conditions  
Min  
Typ  
1
Max  
Unit  
INPUT CHARACTERISTICS  
Offset Voltage  
Input Bias Current  
VOS  
IB  
0 V < VCM < 1.8 V  
4
mV  
pA  
pA  
pA  
pA  
pA  
pA  
V
dB  
dB  
dB  
dB  
10  
100  
600  
5
50  
100  
5
−40°C < TA < +85°C  
−40°C < TA < +125°C  
Input Offset Current  
IOS  
0.5  
−40°C < TA < +85°C  
−40°C < TA < +125°C  
−40°C < TA < +125°C  
VCM = 0 V to 1.8 V  
−40°C < TA < +85°C  
−40°C < TA < +125°C  
0.05 < VOUT < 1.75  
−40°C < TA < +85°C  
−40°C < TA < +125°C  
−40°C < TA < +85°C  
−40°C < TA < +125°C  
Input Voltage Range  
Common-Mode Rejection Ratio  
0
90  
85  
85  
110  
100  
100  
CMRR  
AVO  
105  
100  
Large Signal Voltage Gain  
Offset Voltage Drift  
130  
dB  
dB  
μV/°C  
μV/°C  
2.2  
2.2  
ΔVOS/ΔT  
OUTPUT CHARACTERISTICS  
Output Voltage High  
VOH  
VOL  
ISC  
RL = 100 kΩ to GND  
RL = 10 kΩ to GND  
RL = 100 kΩ to VS  
RL = 10 kΩ to VS  
1.75  
1.65  
TBD  
1.7  
TBD  
TBD  
4
V
V
Output Voltage Low  
Short Circuit Limit  
50  
150  
mV  
mV  
mA  
mA  
mA  
−40°C to +85°C  
−40°C to +125°C  
6
TBD  
POWER SUPPLY  
Power Supply Rejection Ratio  
PSRR  
ISY  
VS = 1.8 V to 5 V  
−40°C to +85°C  
−40°C to +125°C  
VO = VS /2  
105  
100  
90  
120  
120  
120  
18  
dB  
dB  
Supply Current/Amplifier  
20  
28  
μA  
μA  
−40°C < TA < +125°C  
DYNAMIC PERFORMANCE  
Slew Rate  
SR  
GBP  
12  
150  
mV/μs  
kHz  
Gain Bandwidth Product  
NOISE PERFORMANCE  
Peak-to-Peak Noise  
Voltage Noise Density  
Current Noise Density  
en p-p  
en  
in  
f = 0.1 to 10 Hz  
f = 1 kHz  
f = 10 Hz  
2.9  
48  
TBD  
μV p-p  
nV/√Hz  
fA/√Hz  
Rev. PrA | Page 4 of 10  
Preliminary Technical Data  
AD8506  
ABSOLUTE MAXIMUM RATINGS  
Table 3.  
THERMAL RESISTANCE  
θJA is specified for the worst-case conditions, that is, a device  
soldered in a circuit board for surface-mount packages.  
Parameter  
Rating  
6 V  
Vs  
Supply Voltage  
Input Voltage  
Differential Input Voltage1  
Table 4. Thermal Resistance  
Vs  
Package Type  
8-Lead MSOP (RM)  
8-Ball WLCSP  
θJA  
θJC  
Unit  
°C/W  
°C/W  
Output Short-Circuit Duration to Gnd Indefinite  
190  
TBD  
44  
TBD  
Storage Temperature Range RM,  
CB Packages  
−65°C to +150°C  
Operating Temperature Range  
Junction Temperature Range  
RM, CB Packages  
−40°C to +125°C  
−65°C to +150°C  
ESD CAUTION  
Lead Temperature (Soldering, 60 sec)  
300°C  
1
Differential input voltage is limited to 5 V or the supply voltage, whichever  
is less.  
Stresses above those listed under Absolute Maximum Ratings  
may cause permanent damage to the device. This is a stress  
rating only; functional operation of the device at these or any  
other conditions above those indicated in the operational  
section of this specification is not implied. Exposure to absolute  
maximum rating conditions for extended periods may affect  
device reliability.  
Rev. PrA | Page 5 of 10  
AD8506  
Preliminary Technical Data  
TYPICAL PERFORMANCE CHARACTERISTICS  
Figure 3  
Figure 4  
Figure 5  
Figure 6  
Figure 7  
Rev. PrA | Page 6 of 10  
Preliminary Technical Data  
TERMINOLOGY  
AD8506  
Definition Term  
Definition  
Definition Term  
Definition  
Definition Term  
Definition  
Definition Term  
Definition  
Definition Term  
Definition  
Definition Term  
Definition  
Rev. PrA | Page 7 of 10  
AD8506  
Preliminary Technical Data  
THEORY OF OPERATION  
Rev. PrA | Page 8 of 10  
Preliminary Technical Data  
APPLICATIONS INFORMATION  
AD8506  
Rev. PrA | Page 9 of 10  
AD8506  
Preliminary Technical Data  
OUTLINE DIMENSIONS  
3.20  
3.00  
2.80  
8
1
5
4
5.15  
4.90  
4.65  
3.20  
3.00  
2.80  
PIN 1  
0.65 BSC  
0.95  
0.85  
0.75  
1.10 MAX  
0.80  
0.60  
0.40  
8°  
0°  
0.15  
0.00  
0.38  
0.22  
0.23  
0.08  
SEATING  
PLANE  
COPLANARITY  
0.10  
COMPLIANT TO JEDEC STANDARDS MO-187-AA  
Figure 8. 8-Lead Mini Small Outline Package [MSOP]  
(RM-8)  
Dimensions shown in millimeters  
0.675  
0.595  
0.515  
1.480  
1.430  
1.380  
SEATING  
PLANE  
3
2
1
A
B
C
0.340  
0.320  
0.300  
BALL 1  
IDENTIFIER  
1.825  
1.775  
1.725  
0.50  
BALL PITCH  
TOP VIEW  
(BALL SIDE DOWN)  
BOTTOM VIEW  
(BALL SIDE UP)  
0.380  
0.355  
0.330  
0.27  
0.24  
0.21  
Figure 9. 8-Ball Wafer Level Chip Scale Package [WLCSP]  
(CB-8-1)  
Dimensions shown in millimeters  
ORDERING GUIDE  
Model  
Temperature Range  
Package Description  
Package Option  
RM-8  
CB-8-1  
AD8506ARMZ1  
AD8506ACBZ1  
–40°C to +125°C  
–40°C to +125°C  
8-Lead Mini Small Outline Package [MSOP]  
8-Ball Wafer Level Chip Scale Package [WLCSP]  
1 Z = RoHS Compliant Part.  
©2007 Analog Devices, Inc. All rights reserved. Trademarks and  
registered trademarks are the property of their respective owners.  
PR06900-0-8/07(PrA)  
Rev. PrA | Page 10 of 10  

相关型号:

AD8506ARMZ-R2

20 レA Maximum, Rail-to-Rail I/O, Zero Input Crossover Distortion Amplifiers
ADI

AD8506ARMZ-R2

DUAL OP-AMP, 3500 uV OFFSET-MAX, 0.095 MHz BAND WIDTH, PDSO8, ROHS COMPLIANT, MO-187AA, MSOP-8
ROCHESTER

AD8506ARMZ-R7

20 μA Maximum, Rail-to-Rail I/O, Zero Input Crossover Distortion Amplifiers
ADI

AD8506ARMZ-REEL

20 レA Maximum, Rail-to-Rail I/O, Zero Input Crossover Distortion Amplifiers
ADI

AD8506ARMZ-REEL

DUAL OP-AMP, 3500uV OFFSET-MAX, 0.095MHz BAND WIDTH, PDSO8, ROHS COMPLIANT, MO-187AA, MSOP-8
ROCHESTER

AD8506_07

20 レA Maximum, Rail-to-Rail I/O, Zero Input Crossover Distortion Amplifiers
ADI

AD8508

20 レA Maximum, Rail-to-Rail I/O, Zero Input Crossover Distortion Amplifiers
ADI

AD8508ACBZ-REEL

20 μA Maximum, Rail-to-Rail I/O, Zero Input Crossover Distortion Amplifiers
ADI

AD8508ACBZ-REEL7

20 μA Maximum, Rail-to-Rail I/O, Zero Input Crossover Distortion Amplifiers
ADI

AD8508ARUZ

20 レA Maximum, Rail-to-Rail I/O, Zero Input Crossover Distortion Amplifiers
ADI

AD8508ARUZ

QUAD OP-AMP, 3500 uV OFFSET-MAX, 0.095 MHz BAND WIDTH, PDSO14, ROHS COMPLIANT, MO-153AB-1, TSSOP-14
ROCHESTER

AD8508ARUZ-REEL

20 レA Maximum, Rail-to-Rail I/O, Zero Input Crossover Distortion Amplifiers
ADI