AD9639BCPZ-210 [ADI]
Quad, 12-Bit, 170 MSPS/210 MSPS Serial Output 1.8 V ADC; 四通道，12位， 170 MSPS / 210 MSPS串行输出1.8 V ADC
| 型号： | AD9639BCPZ-210 |
| 厂家： | 
ADI |
| 描述： | Quad, 12-Bit, 170 MSPS/210 MSPS Serial Output 1.8 V ADC |
| 文件： | 总36页 (文件大小：855K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Quad, 12-Bit, 170 MSPS/210 MSPS
Serial Output 1.8 V ADC
Data Sheet
AD9639
FEATURES
FUNCTIONAL BLOCK DIAGRAM
AVDD
PDWN
DRVDD DRGND
4 ADCs in one package
JESD204 coded serial digital outputs
On-chip temperature sensor
−95 dB channel-to-channel crosstalk
SNR: 65 dBFS with AIN = 85 MHz at 210 MSPS
SFDR: 77 dBc with AIN = 85 MHz at 210 MSPS
Excellent linearity
DNL: 0.28 LSB (typical)
INL: 0.7 LSB (typical)
780 MHz full power analog bandwidth
Power dissipation: 325 mW per channel at 210 MSPS
1.25 V p-p input voltage range, adjustable up to 1.5 V p-p
1.8 V supply operation
AD9639
VIN + A
VIN – A
VCM A
VIN + B
VIN – B
VCM B
DOUT + A
DOUT – A
PIPELINE
ADC
SHA
12
12
12
12
CHANNEL A
BUF
BUF
BUF
BUF
DOUT + B
DOUT – B
PIPELINE
ADC
SHA
SHA
SHA
CHANNEL B
CHANNEL C
CHANNEL D
VIN + C
VIN – C
VCM C
VIN + D
VIN – D
VCM D
DOUT + C
DOUT – C
PIPELINE
ADC
DOUT + D
DOUT – D
PIPELINE
ADC
Clock duty cycle stabilizer
Serial port interface features
Power-down modes
Digital test pattern enable
Programmable header
PGM3
PGM2
PGM1
PGM0
RESET
REFERENCE
RBIAS
DATA RATE
MULTIPLIER
SERIAL
PORT
TEMPOUT
Programmable pin functions (PGMx, PDWN)
SCLK SDI/ SDO CSB
SDIO
CLK+ CLK–
APPLICATIONS
Communication receivers
Figure 1.
Cable head end equipment/M-CMTS
Broadband radios
Wireless infrastructure transceivers
Radar/military-aerospace subsystems
Test equipment
GENERAL DESCRIPTION
The AD9639 is a quad, 12-bit, 210 MSPS analog-to-digital con-
verter (ADC) with an on-chip temperature sensor and a high
speed serial interface. It is designed to support the digitizing
of high frequency, wide dynamic range signals with an input
bandwidth of up to 780 MHz. The output data is serialized
and presented in packet format, consisting of channel-specific
information, coded samples, and error code correction.
Fabricated on an advanced CMOS process, the AD9639 is avail-
able in a Pb-free/RoHS-compliant, 72-lead LFCSP package. It is
specified over the industrial temperature range of −40°C to +85°C.
PRODUCT HIGHLIGHTS
1. Four ADCs are contained in a small, space-saving package.
2. An on-chip PLL allows users to provide a single ADC
sampling clock; the PLL distributes and multiplies up to
produce the corresponding data rate clock.
3. The JESD204 coded data rate supports up to 4.2 Gbps
per channel.
4. The AD9639 operates from a single 1.8 V power supply.
5. Flexible synchronization schemes and programmable
mode pins are available.
The ADC requires a single 1.8 V power supply. The input clock
can be driven differentially with a sine wave, LVPECL, CMOS,
or LVDS. A clock duty cycle stabilizer allows high performance
at full speed with a wide range of clock duty cycles. The on-chip
reference eliminates the need for external decoupling and can
be adjusted by means of SPI control.
Various power-down and standby modes are supported. The
ADC typically consumes 150 mW per channel with the digital
link still in operation when standby operation is enabled.
6. An on-chip temperature sensor is included.
Rev. B
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2009–2013 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD9639
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Theory of Operation ...................................................................... 17
Analog Input Considerations ................................................... 17
Clock Input Considerations...................................................... 19
Digital Outputs ........................................................................... 21
Serial Port Interface (SPI).............................................................. 29
Hardware Interface..................................................................... 29
Memory Map .................................................................................. 31
Reading the Memory Map Table.............................................. 31
Reserved Locations .................................................................... 31
Default Values............................................................................. 31
Logic Levels................................................................................. 31
Applications Information.............................................................. 35
Power and Ground Recommendations................................... 35
Exposed Paddle Thermal Heat Slug Recommendations ...... 35
Outline Dimensions....................................................................... 36
Ordering Guide .......................................................................... 36
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description......................................................................... 1
Product Highlights ........................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
AC Specifications.......................................................................... 4
Digital Specifications ................................................................... 5
Switching Specifications .............................................................. 6
Timing Diagram ........................................................................... 7
Absolute Maximum Ratings............................................................ 8
Thermal Resistance ...................................................................... 8
ESD Caution.................................................................................. 8
Pin Configuration and Function Descriptions............................. 9
Typical Performance Characteristics ........................................... 11
Equivalent Circuits......................................................................... 15
REVISION HISTORY
7/13—Rev. A to Rev. B
Change to Current Drive Parameter, Table 1................................ 3
Updated Outline Dimensions ....................................................... 36
2/10—Rev. 0 to Rev. A
Changes to Differential Input Voltage Range Parameter,
Table 1 ................................................................................................ 3
Changes to Table 7............................................................................ 9
Changes to Digital Outputs and Timing Section ....................... 25
Change to Addr. (Hex) 0x01, Table 15......................................... 32
5/09—Revision 0: Initial Version
Rev. B | Page 2 of 36
Data Sheet
AD9639
SPECIFICATIONS
AVDD = 1.8 V, DRVDD = 1.8 V, TMIN = −40°C, TMAX = +85°C, 1.25 V p-p differential input, AIN = −1.0 dBFS, DCS enabled, unless
otherwise noted.
Table 1.
AD9639BCPZ-170
AD9639BCPZ-210
Parameter1
Temp
Min
Typ
Max
Min
Typ
Max
Unit
RESOLUTION
12
12
Bits
ACCURACY
No Missing Codes
Offset Error
Offset Matching
Gain Error
Full
Guaranteed
−2
4
+1
0.9
0.28
0.45
Guaranteed
−2
4
+1
0.9
0.28
0.7
25°C
25°C
25°C
25°C
Full
12
12
+4.7
2.7
0.6
0.9
12
12
+4.7
2.7
0.6
1.3
mV
mV
% FS
% FS
LSB
LSB
−2.8
1.0
−2.8
1.0
Gain Matching
Differential Nonlinearity (DNL)
Integral Nonlinearity (INL)
ANALOG INPUTS
Differential Input Voltage Range2
Common-Mode Voltage
Input Capacitance
Input Resistance
Analog Bandwidth, Full Power
Voltage Common Mode (VCM x Pins)
Voltage Output
Full
Full
Full
25°C
Full
Full
1.25
1.4
2
4.3
780
1.5
1.25
1.4
2
4.3
780
1.5
V p-p
V
pF
kΩ
MHz
Full
Full
1.4
1.44
1
1.5
1.4
1.44
1
1.5
V
Current Drive
mA
mV/°C
mV
µA
TEMPERATURE SENSOR OUTPUT
Voltage Output
Current Drive
−1.12
739
50
−1.12
737
50
Full
Full
POWER SUPPLY
AVDD
DRVDD
IAVDD
IDRVDD
Full
Full
Full
Full
Full
1.7
1.7
1.8
1.8
535
98
1.139
1.9
1.9
570
105
1.215
1.7
1.7
1.8
1.8
610
111
1.298
1.9
1.9
650
120
1.386
V
V
mA
mA
W
Total Power Dissipation
(Including Output Drivers)
Power-Down Dissipation
Standby Dissipation2
CROSSTALK
Full
Full
Full
Full
3
3
mW
mW
dB
152
−95
−90
173
−95
−90
Overrange Condition3
dB
1 See the AN-835 Application Note, Understanding High Speed ADC Testing and Evaluation, for definitions and details on how these tests were completed.
2 AVDD/DRVDD, with link established.
3 Overrange condition is specified as 6 dB above the full-scale input range.
Rev. B | Page 3 of 36
AD9639
Data Sheet
AC SPECIFICATIONS
AVDD = 1.8 V, DRVDD = 1.8 V, TMIN = −40°C, TMAX = +85°C, 1.25 V p-p differential input, AIN = −1.0 dBFS, DCS enabled, unless
otherwise noted.
Table 2.
AD9639BCPZ-170
AD9639BCPZ-210
Parameter1
Temp
Min
Typ
Max
Min
Typ
Max
Unit
SIGNAL-TO-NOISE RATIO (SNR)
fIN = 84.3 MHz
fIN = 240.3 MHz
Full
25°C
63.5
64.5
64.1
63.2
64.2
63.2
dB
dB
SIGNAL-TO-(NOISE + DISTORTION) (SINAD) RATIO
fIN = 84.3 MHz
fIN = 240.3 MHz
Full
25°C
63.3
10.2
64.4
63.9
62.8
10.1
63.9
63
dB
dB
EFFECTIVE NUMBER OF BITS (ENOB)
fIN = 84.3 MHz
fIN = 240.3 MHz
Full
25°C
10.4
10.3
10.3
10.2
Bits
Bits
WORST HARMONIC (SECOND)
fIN = 84.3 MHz
fIN = 240.3 MHz
Full
25°C
87.5
82
78.6
74
86
80
77
dBc
dBc
WORST HARMONIC (THIRD)
fIN = 84.3 MHz
fIN = 240.3 MHz
Full
25°C
79
84
76
77
72.6
83.7
dBc
dBc
WORST OTHER (EXCLUDING SECOND OR THIRD)
fIN = 84.3 MHz
fIN = 240.3 MHz
Full
25°C
96
88
86
90
88
dBc
dBc
TWO-TONE INTERMODULATION DISTORTION (IMD)
fIN1 = 140.2 MHz, fIN2 = 141.3 MHz,
AIN1 and AIN2 = −7.0 dBFS
fIN1 = 170.2 MHz, fIN2 = 171.3 MHz,
AIN1 and AIN2 = −7.0 dBFS2
25°C
25°C
78
77
77
dBc
dBc
1 See the AN-835 Application Note, Understanding High Speed ADC Testing and Evaluation, for definitions and details on how these tests were completed.
2 Tested at 170 MSPS and 210 MSPS.
Rev. B | Page 4 of 36
Data Sheet
AD9639
DIGITAL SPECIFICATIONS
AVDD = 1.8 V, DRVDD = 1.8 V, TMIN = −40°C, TMAX = +85°C, 1.25 V p-p differential input, AIN = −1.0 dBFS, DCS enabled, unless
otherwise noted.
Table 3.
AD9639BCPZ-170
AD9639BCPZ-210
Parameter1
Temp
Min
Typ
Max
Min
Typ
Max
Unit
CLOCK INPUTS (CLK+, CLK−)
Logic Compliance
Differential Input Voltage
Input Voltage Range
Full
Full
Full
LVPECL/LVDS/CMOS
6
LVPECL/LVDS/CMOS
6
0.2
AVDD −
0.3
0.2
AVDD −
0.3
V p-p
AVDD +
1.6
AVDD +
1.6
Internal Common-Mode Bias
Input Common-Mode Voltage
High Level Input Voltage (VIH)
Low Level Input Voltage (VIL)
High Level Input Current (IIH)
Low Level Input Current (IIL)
Differential Input Resistance
Input Capacitance
Full
Full
Full
Full
Full
Full
25°C
25°C
1.2
1.2
V
V
V
V
µA
µA
kΩ
pF
1.1
1.2
0
−10
−10
16
AVDD
3.6
0.8
+10
+10
24
1.1
1.2
0
−10
−10
16
AVDD
3.6
0.8
+10
+10
24
20
4
20
4
LOGIC INPUTS (PDWN, CSB, SDI/SDIO,
SCLK, RESET, PGMx)2
Logic 1 Voltage
Full
Full
0.8 ×
AVDD
0.8 ×
AVDD
V
V
Logic 0 Voltage
0.2 ×
0.2 ×
AVDD
AVDD
Logic 1 Input Current (CSB)
Logic 0 Input Current (CSB)
Logic 1 Input Current
(PDWN, SDI/SDIO, SCLK,
RESET, PGMx)
Full
Full
Full
0
−60
55
0
−60
55
µA
µA
µA
Logic 0 Input Current
(PDWN, SDI/SDIO, SCLK,
RESET, PGMx)
Full
0
0
µA
Input Resistance
Input Capacitance
LOGIC OUTPUT (SDO)
Logic 1 Voltage
25°C
25°C
30
4
30
4
kΩ
pF
Full
Full
1.2
0
AVDD +
0.3
0.3
1.2
0
AVDD +
0.3
0.3
V
V
Logic 0 Voltage
DIGITAL OUTPUTS (DOUT + x, DOUT − x)
Logic Compliance
CML
CML
Differential Output Voltage
Common-Mode Voltage
Full
Full
0.8
DRVDD/2
0.8
DRVDD/2
V
V
1 See the AN-835 Application Note, Understanding High Speed ADC Testing and Evaluation, for definitions and details on how these tests were completed.
2 Specified for 13 SDI/SDIO pins on the same SPI bus.
Rev. B | Page 5 of 36
AD9639
Data Sheet
SWITCHING SPECIFICATIONS
AVDD = 1.8 V, DRVDD = 1.8 V, TMIN = −40°C, TMAX = +85°C, 1.25 V p-p differential input, AIN = −1.0 dBFS, DCS enabled, unless
otherwise noted.
Table 4.
AD9639BCPZ-170
AD9639BCPZ-210
Parameter1
Temp
Min
Typ
Max
Min
Typ
Max
Unit
CLOCK
Clock Rate
Full
Full
Full
100
2.65
2.65
170
100
2.15
2.15
210
MSPS
ns
ns
Clock Pulse Width High (tEH)
Clock Pulse Width Low (tEL)
DATA OUTPUT PARAMETERS
2.9
2.9
2.4
2.4
Data Output Period or UI
(DOUT + x, DOUT − x)
Full
1/(20 × fCLK
)
1/(20 × fCLK
)
Seconds
Data Output Duty Cycle
Data Valid Time
25°C
25°C
25°C
25°C
25°C
Full
25°C
25°C
25°C
25°C
25°C
25°C
50
0.8
4
250
50
50
0.8
4
250
50
%
UI
µs
ns
PLL Lock Time (tLOCK
)
Wake-Up Time (Standby)
Wake-Up Time (Power-Down)2
Pipeline Latency
Data Rate per Channel (NRZ)
Deterministic Jitter
μs
40
40
CLK cycles
Gbps
ps
ps rms
Seconds
CLK cycles
ps
3.4
10
6
0
1
50
4.2
10
6
0
1
50
Random Jitter
Channel-to-Channel Bit Skew
Channel-to-Channel Packet Skew3
Output Rise/Fall Time
TERMINATION CHARACTERISTICS
Differential Termination Resistance
APERTURE
25°C
100
100
Ω
Aperture Delay (tA)
Aperture Uncertainty (Jitter)
OUT-OF-RANGE RECOVERY TIME
25°C
25°C
25°C
1.2
0.2
1
1.2
0.2
1
ns
ps rms
CLK cycles
1 See the AN-835 Application Note, Understanding High Speed ADC Testing and Evaluation, for definitions and details on how these tests were completed.
2 Receiver dependent.
3 See the Serial Data Frame section.
Rev. B | Page 6 of 36
Data Sheet
AD9639
TIMING DIAGRAM
SAMPLE
N
N + 1
N – 40
N – 39
ANALOG
INPUT SIGNAL
N – 38
N – 37
SAMPLE
RATE CLOCK
SAMPLE
...
SERIA.L..CODED SAMPLES: N – 40, N – 39, N – 38, N – 37 ...
...
RATE CLOCK
SERIAL
DATA OUTPUT
...
...
...
...
...
Figure 2. Timing Diagram
Rev. B | Page 7 of 36
AD9639
Data Sheet
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Table 5.
The exposed paddle must be soldered to the ground plane for the
LFCSP package. Soldering the exposed paddle to the printed
circuit board (PCB) increases the reliability of the solder joints,
maximizing the thermal capability of the package.
Parameter
Rating
AVDD to AGND
−0.3 V to +2.0 V
−0.3 V to +2.0 V
−0.3 V to +0.3 V
−2.0 V to +2.0 V
−0.3 V to DRVDD + 0.3 V
DRVDD to DRGND
AGND to DRGND
AVDD to DRVDD
DOUT + x/DOUT − x to DRGND
SDO, SDI/SDIO, CLK , VIN x, VCM x, −0.3 V to AVDD + 0.3 V
TEMPOUT, RBIAS to AGND
Table 6. Thermal Resistance
Package Type
θJA
θJB
θJC
Unit
72-Lead LFCSP (CP-72-3)
16.2
7.9
0.6
°C/W
SCLK, CSB, PGMx, RESET, PDWN
to AGND
−0.3 V to AVDD + 0.3 V
Typical θJA, θJB, and θJC values are specified for a 4-layer board in
still air. Airflow increases heat dissipation, effectively reducing
θJA. In addition, metal in direct contact with the package leads
from metal traces, through holes, ground, and power planes
reduces θJA.
Storage Temperature Range
Operating Temperature Range
Lead Temperature (Soldering, 10 sec) 300°C
Junction Temperature 150°C
−65°C to +125°C
−40°C to +85°C
ESD CAUTION
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. B | Page 8 of 36
Data Sheet
AD9639
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
NC
TEMPOUT
RBIAS
AVDD
NC
1
2
3
4
5
6
7
8
9
54 NC
PIN 1
INDICATOR
53 PGM0
52 PGM1
51 PGM2
50 PGM3
49 NC
48 AVDD
47 VCM A
46 AVDD
45 VIN – A
44 VIN + A
43 AVDD
42 AVDD
41 AVDD
40 CSB
PIN 0 = EPAD = AGND
NC
AVDD
VCM D
AVDD
TOP VIEW
(Not to Scale)
VIN – D 10
VIN + D 11
AVDD 12
AVDD 13
AVDD 14
AVDD 15
CLK– 16
CLK+ 17
AVDD 18
39 SCLK
38 SDI/SDIO
37 SDO
NOTES
1. NC = NO CONNECT.
2. THE EXPOSED PADDLE MUST BE SOLDERED TO THE GROUND PLANE
FOR THE LFCSP PACKAGE. SOLDERING THE EXPOSED PADDLE TO
THE PCB INCREASES THE RELIABILITY OF THE SOLDER JOINTS,
MAXIMIZING THE THERMAL CAPABILITY OF THE PACKAGE.
Figure 3. Pin Configuration
Table 7. Pin Function Descriptions
Pin No.
Mnemonic
Description
0
AGND
Analog Ground (Exposed Paddle). The exposed paddle must be soldered to the ground
plane. Soldering the exposed paddle to the PCB increases the reliability of the solder joints,
maximizing the thermal capability of the package.
1, 5, 6, 19, 36, 49, 54,
63, 72
NC
No Connection.
2
3
TEMPOUT
RBIAS
AVDD
Output Voltage to Monitor Temperature.
External Resistor to Set the Internal ADC Core Bias Current.
1.8 V Analog Supply.
4, 7, 9, 12, 13, 14, 15,
18, 20, 21, 41, 42, 43,
46, 48, 55, 57, 60, 61,
62, 64, 65, 66, 69, 71
8
10
11
16
VCM D
Common-Mode Output Voltage Reference.
ADC D Analog Input Complement.
ADC D Analog Input True.
VIN − D
VIN + D
CLK−
Clock Input Complement.
17
CLK+
Clock Input True.
22
RESET
Reset Enable Pin. Resets the digital output timing.
Digital Output Driver Ground.
1.8 V Digital Output Driver Supply.
ADC D Digital Output True.
ADC D Digital Output Complement.
ADC C Digital Output True.
ADC C Digital Output Complement.
ADC B Digital Output True.
ADC B Digital Output Complement.
23, 34
24, 33
25
26
27
28
29
30
DRGND
DRVDD
DOUT + D
DOUT − D
DOUT + C
DOUT − C
DOUT + B
DOUT − B
Rev. B | Page 9 of 36
AD9639
Data Sheet
Pin No.
Mnemonic
DOUT + A
DOUT − A
PDWN
Description
31
32
35
ADC A Digital Output True.
ADC A Digital Output Complement.
Power-Down.
37
38
39
SDO
SDI/SDIO
SCLK
Serial Data Output for 4-Wire SPI Interface.
Serial Data Input/Serial Data Input/Output for 3-Wire SPI Interface.
Serial Clock.
40
CSB
Chip Select Bar.
44
45
47
VIN + A
VIN − A
VCM A
PGM3, PGM2,
PGM1, PGM0
ADC A Analog Input True.
ADC A Analog Input Complement.
Common-Mode Output Voltage Reference.
Optional Pins to be Programmed by Customer.
50, 51, 52, 53
56
58
59
67
68
70
VCM B
VIN − B
VIN + B
VIN + C
VIN − C
VCM C
Common-Mode Output Voltage Reference.
ADC B Analog Input Complement.
ADC B Analog Input True.
ADC C Analog Input True.
ADC C Analog Input Complement.
Common-Mode Output Voltage Reference.
Rev. B | Page 10 of 36
Data Sheet
AD9639
TYPICAL PERFORMANCE CHARACTERISTICS
0
0
AIN = –1.0dBFS
SNR = 63.13dB
AIN = –1.0dBFS
SNR = 64.88dB
ENOB = 10.19 BITS
SFDR = 76.07dBc
ENOB = 10.49 BITS
SFDR = 77.57dBc
–20
–20
–40
–60
–40
–60
–80
–80
–100
–120
–100
–120
0
10
20
30
40
50
60
70
80
0
20
40
60
80
100
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 4. Single-Tone 32k FFT with fIN = 84.3 MHz, fSAMPLE = 170 MSPS
Figure 7. Single-Tone 32k FFT with fIN = 240.3 MHz, fSAMPLE = 210 MSPS
70
69
68
67
66
65
64
0
AIN = –1.0dBFS
SNR = 63.95dB
ENOB = 10.33 BITS
SFDR = 78.90dBc
–20
–40
–60
170MSPS
210MSPS
–80
63
62
61
60
–100
–120
0
10
20
30
40
50
60
70
80
50
70
90
110 130 150 170 190 210 230 250
ENCODE (MSPS)
FREQUENCY (MHz)
Figure 5. Single-Tone 32k FFT with fIN = 240.3 MHz, fSAMPLE = 170 MSPS
Figure 8. SNR vs. Encode, fIN = 84.3 MHz
90
88
86
84
82
80
78
76
74
72
70
0
AIN = –1.0dBFS
SNR = 64.65dB
ENOB = 10.44 BITS
SFDR = 77.54dBc
–20
–40
–60
170MSPS
–80
210MSPS
–100
–120
0
20
40
60
80
100
50
70
90
110 130 150 170 190 210 230 250
ENCODE (MSPS)
FREQUENCY (MHz)
Figure 6. Single-Tone 32k FFT with fIN = 84.3 MHz, fSAMPLE = 210 MSPS
Figure 9. SFDR vs. Encode, fIN = 84.3 MHz
Rev. B | Page 11 of 36
AD9639
Data Sheet
100
90
80
70
60
50
40
30
20
10
0
AIN1 AND AIN2 = –7.0dBFS
SFDR = 75.44dBc
IMD2 = –78.34dBc
SFDR (dBFS)
–20
IMD3 = –75.44dBc
SNR (dBFS)
–40
–60
SFDR (dB)
–80
SNR (dB)
–100
–120
0
0
20
40
60
80
100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
FREQUENCY (MHz)
ANALOG INPUT LEVEL (dBFS)
Figure 10. SNR/SFDR vs. Analog Input Level, fIN = 84.3 MHz, fSAMPLE = 170 MSPS
Figure 13. Two-Tone 32k FFT with fIN1 = 140.2 MHz and fIN2 = 141.3 MHz,
fSAMPLE = 210 MSPS
100
0
AIN1 AND AIN2 = –7.0dBFS
SFDR = 76.88dBc
IMD2 = –78.75dBc
IMD3 = –78.68dBc
90
SFDR (dBFS)
–20
80
70
60
50
40
30
SNR (dBFS)
SFDR (dB)
–40
–60
–80
SNR (dB)
20
10
0
–100
–120
0
20
40
60
80
100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
FREQUENCY (MHz)
ANALOG INPUT LEVEL (dBFS)
Figure 11. SNR/SFDR vs. Analog Input Level, fIN = 84.3 MHz, fSAMPLE = 210 MSPS
Figure 14. Two-Tone 32k FFT with fIN1 = 170.2 MHz and fIN2 = 171.3 MHz,
fSAMPLE = 210 MSPS
0
95
90
85
AIN1 AND AIN2 = –7.0dBFS
SFDR = 77.26dBc
IMD2 = –86.55dBc
IMD3 = –77.26dBc
–20
80
–40
–60
SFDR (dB)
75
70
65
SNR (dB)
–80
60
55
50
45
–100
–120
0
10
20
30
40
50
60
70
80
0
50
100 150 200 250 300 350 400 450 500
AIN FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 15. SNR/SFDR Amplitude vs. AIN Frequency, fSAMPLE = 170 MSPS
Figure 12. Two-Tone 32k FFT with fIN1 = 140.2 MHz and fIN2 = 141.3 MHz,
fSAMPLE = 170 MSPS
Rev. B | Page 12 of 36
Data Sheet
AD9639
95
90
85
80
75
70
65
60
55
50
45
0.8
0.6
0.4
SFDR (dB)
0.2
0
–0.2
–0.4
–0.6
–0.8
SNR (dB)
0
50
100 150 200 250 300 350 400 450 500
AIN FREQUENCY (MHz)
0
500 1000 1500 2000 2500 3000 3500 4000 4500
CODE
Figure 16. SNR/SFDR Amplitude vs. AIN Frequency, fSAMPLE = 210 MSPS
Figure 19. INL, fIN = 9.7 MHz, fSAMPLE = 210 MSPS
70
69
68
0.4
0.2
0
67
SNR, 170MSPS
–0.2
–0.4
–0.6
–0.8
–1.0
–1.2
SNR, 210MSPS
66
65
64
63
62
61
60
–40
–20
0
20
40
60
80
0
500 1000 1500 2000 2500 3000 3500 4000 4500
CODE
TEMPERATURE (°C)
Figure 17. SNR vs. Temperature, fIN = 84.3 MHz
Figure 20. DNL, fIN = 9.7 MHz, fSAMPLE = 210 MSPS
90
85
80
75
70
40,000
35,000
30,000
25,000
20,000
15,000
10,000
5000
INPUT REFERRED NOISE: 0.72 LSB
SFDR, 210MSPS
SFDR, 170MSPS
65
60
0
–40
–20
0
20
40
60
80
N – 3 N – 2 N – 1
N
N + 1 N + 2 N + 3 MORE
BIN
TEMPERATURE (°C)
Figure 18. SFDR vs. Temperature, fIN = 84.3 MHz
Figure 21. Input-Referred Noise Histogram, fSAMPLE = 170 MSPS
Rev. B | Page 13 of 36
AD9639
Data Sheet
40,000
35,000
30,000
25,000
20,000
15,000
10,000
5000
90
85
80
75
70
65
60
55
50
45
40
INPUT REFERRED NOISE: 0.70 LSB
SFDR
SNR
0
N – 3 N – 2 N – 1
N
N + 1 N + 2 N + 3 MORE
BIN
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
ANALOG INPUT COMMON-MODE VOLTAGE (V)
Figure 22. Input-Referred Noise Histogram, fSAMPLE = 210 MSPS
Figure 24. SNR/SFDR vs. Analog Input Common-Mode Voltage,
fIN = 84.3 MHz, fSAMPLE = 210 MSPS
0
–20
–40
–60
–80
0
–5
–10
–15
–20
–25
–100
–120
0
20
40
60
80
100
120
1M
10M
100M
1G
FREQUENCY (Hz)
AIN FREQUENCY (Hz)
Figure 23. Noise Power Ratio (NPR), fSAMPLE = 210 MSPS
Figure 25. Full-Power Bandwidth Amplitude vs. AIN Frequency, fSAMPLE = 210 MSPS
Rev. B | Page 14 of 36
Data Sheet
AD9639
EQUIVALENT CIRCUITS
AVDD
AVDD
AVDD
1.2V
10kΩ
10kΩ
CLK+
CLK–
250Ω
SDI/SDIO
30kΩ
Figure 26. CLK Inputs
Figure 30. Equivalent SDI/SDIO Input Circuit
AVDD
AVDD
VIN + x
BUF
2kΩ
AVDD
BUF
~1.4V
AVDD
2kΩ
TEMPOUT
VIN – x
BUF
Figure 27. Analog Inputs
Figure 31. Equivalent TEMPOUT Output Circuit
100Ω
175Ω
175Ω
30kΩ
RBIAS
SCLK,
PDWN,
PGMx,
RESET
Figure 32. Equivalent RBIAS Input/Output Circuit
Figure 28. Equivalent SCLK, RESET, PDWN, PGMx Input Circuit
AVDD
175Ω
VCM x
26kΩ
1kΩ
CSB
Figure 33. Equivalent VCM x Output Circuit
Figure 29. Equivalent CSB Input Circuit
Rev. B | Page 15 of 36
AD9639
Data Sheet
AVDD
SDO
DRVDD
AVDD
4mA
4mA
4mA
4mA
R
TERM
V
DOUT + x
DOUT – x
CM
345Ω
Figure 35. Equivalent SDO Output Circuit
Figure 34. Equivalent Digital Output Circuit
Rev. B | Page 16 of 36
Data Sheet
AD9639
THEORY OF OPERATION
The AD9639 architecture consists of a differential input buffer and
a front-end sample-and-hold amplifier (SHA) followed by a pipe-
lined switched-capacitor ADC. The quantized outputs from each
stage are combined into a final 12-bit result in the digital correction
logic. The pipelined architecture permits the first stage to operate
on a new input sample while the remaining stages operate on pre-
ceding samples. Sampling occurs on the rising edge of the clock.
with each input can help to reduce the peak transient current
injected from the output stage of the driving source.
In addition, low Q inductors or ferrite beads can be placed on
each leg of the input to reduce high differential capacitance at
the analog inputs and, therefore, achieve the maximum band-
width of the ADC. The use of low Q inductors or ferrite beads is
required when driving the converter front end at high IF
frequencies. Either a shunt capacitor or two single-ended
capacitors can be placed on the inputs to provide a matching
passive network. This ultimately creates a low-pass filter at the
input to limit unwanted broadband noise. See the AN-827
Application Note and the Analog Dialogue article “Transformer-
Coupled Front-End for Wideband A/D Converters” (Volume 39,
Number 2, April 2005) for more information on this subject. In
general, the precise values depend on the application.
Each stage of the pipeline, excluding the last, consists of a low
resolution flash ADC connected to a switched-capacitor DAC
and interstage residue amplifier (for example, a multiplying
digital-to-analog converter (MDAC)). The residue amplifier
magnifies the difference between the reconstructed DAC output
and the flash input for the next stage in the pipeline. One bit of
redundancy is used in each stage to facilitate digital correction
of flash errors. The last stage simply consists of a flash ADC.
The input stage contains a differential SHA that can be ac- or
dc-coupled in differential or single-ended mode. The output of
the pipeline ADC is put into its final serial format by the data
serializer, encoder, and CML drivers block. The data rate multiplier
creates the clock used to output the high speed serial data at the
CML outputs.
Maximum SNR performance is achieved by setting the ADC to
the largest span in a differential configuration. In the case of the
AD9639, the default input span is 1.25 V p-p. To configure the ADC
for a different input span, see the VREF register (Address 0x18).
For the best performance, an input span of 1.25 V p-p or greater
should be used (see Table 15 for details).
Differential Input Configurations
ANALOG INPUT CONSIDERATIONS
The AD9639 can be driven actively or passively; in either case,
optimum performance is achieved by driving the analog input
differentially. For example, using the ADA4937 differential ampli-
fier to drive the AD9639 provides excellent performance and a
flexible interface to the ADC for baseband and second Nyquist
(~100 MHz IF) applications (see Figure 36 and Figure 37). In either
application, use 1% resistors for good gain matching. Note that the
dc-coupled configuration shows some degradation in spurious per-
formance. For more information, consult the ADA4937 data sheet.
The analog input to the AD9639 is a differential buffer. This
input is optimized to provide superior wideband performance
and requires that the analog inputs be driven differentially. SNR
and SINAD performance degrades if the analog input is driven
with a single-ended signal.
For best dynamic performance, the source impedances driving
VIN + x and VIN − x should be matched such that common-mode
settling errors are symmetrical. These errors are reduced by the
common-mode rejection of the ADC. A small resistor in series
3.3V
1.8V
1.8V
205Ω
0.1µF
1.25V p-p
200Ω
1.65V
24Ω
24Ω
33Ω
VIN + x
AVDD DRVDD
+V
S
62Ω
SIGNAL
GENERATOR
10kΩ
10kΩ
V
AD9639
ADC INPUT
OCM
ADA4937
G = UNITY
OPTIONAL C
C
R
0.1µF
IMPEDANCE
200Ω
27Ω
–V
S
VIN – x
33Ω
0.1µF
205Ω
Figure 36. Differential Amplifier Configuration for AC-Coupled Baseband Applications
3.3V
1.8V
1.8V
205Ω
1.25V p-p
62Ω
0.1µF
24Ω
33Ω
200Ω
VIN + x
AVDD DRVDD
+V
S
AD9639
ADC INPUT
SIGNAL
GENERATOR
V
OCM
ADA4937
G = UNITY
OPTIONAL C
C
R
IMPEDANCE
200Ω
27Ω
–V
S
VCM x
VIN – x
24Ω
33Ω
205Ω
1.4V
Figure 37. Differential Amplifier Configuration for DC-Coupled Baseband Applications
Rev. B | Page 17 of 36
AD9639
Data Sheet
1.25V p-p
0.1µF
0.1µF
BALUN
1:1 Z
For applications where SNR is a key parameter, differential
transformer coupling is the recommended input configuration
to achieve the true performance of the AD9639 (see Figure 38
to Figure 40).
33Ω
VIN + x
ADC
AD9639
4.7pF
66Ω
0.1µF
33Ω
VIN – x
Regardless of the configuration, the value of the shunt capacitor, C,
is dependent on the input frequency and may need to be reduced
or removed.
BALUN
1:1 Z
ADT1-1WT
1:1 Z RATIO
C
33Ω
VIN + x
Figure 41. Differential Balun-Coupled Configuration
for Wideband IF Applications
ADC
AD9639
0.1µF
1.25Vp-p
50Ω
*C
DIFF
Single-Ended Input Configuration
33Ω
VIN – x
AGND
C
A single-ended input may provide adequate performance in
cost-sensitive applications. In this configuration, SFDR and
distortion performance can degrade due to input common-mode
swing mismatch. If the application requires a single-ended input
configuration, ensure that the source impedances on each input
are well matched to achieve the best possible performance. A
full-scale input of 1.25 V p-p can be applied to the VIN + x pin
of the AD9639 while the VIN − x pin is terminated. Figure 42
shows a typical single-ended input configuration.
0.1μF
*C
DIFF IS OPTIONAL
Figure 38. Differential Transformer-Coupled Configuration
for Baseband Applications
ADT1-1WT
1:1 Z RATIO
1.25Vp-p
0.1μF
L
L
33Ω
VIN + x
65Ω
2.2pF
ADC
250Ω
AD9639
L
33Ω
VIN – x
C
0.1μF
33Ω
VIN + x
0.1µF
49.9Ω
1.25V p-p
Figure 39. Differential Transformer-Coupled Configuration
for Wideband IF Applications
ADC
AD9639
*C
DIFF
25Ω
33Ω
VIN – x
C
0.1µF
ADT1-1WT
1.25Vp-p
0.1μF
1:1 Z RATIO
33Ω
33Ω
VIN + x
*C
DIFF IS OPTIONAL
ADC
250Ω
L
Figure 42. Single-Ended Input Configuration
AD9639
VIN – x
0.1μF
Figure 40. Differential Transformer-Coupled Configuration
for Narrow-Band IF Applications
Rev. B | Page 18 of 36
Data Sheet
AD9639
CLK+ input circuit supply is AVDD (1.8 V), this input is
designed to withstand input voltages of up to 3.3 V and,
therefore, offers several selections for the drive logic voltage.
CLOCK INPUT CONSIDERATIONS
For optimum performance, the AD9639 sample clock inputs
(CLK+ and CLK−) should be clocked with a differential signal.
This signal is typically ac-coupled to the CLK+ and CLK− pins
via a transformer or capacitors. These pins are biased internally
to 1.2 V and require no additional biasing.
AD9510/AD9511/
AD9512/AD9513/
AD9514/AD9515/
0.1µF
AD9516/AD9518
CLK+
CLK
OPTIONAL
100Ω
50Ω*
Figure 43 shows a preferred method for clocking the AD9639. The
low jitter clock source is converted from a single-ended signal
to a differential signal using an RF transformer. The back-to-
back Schottky diodes across the secondary transformer limit
clock excursions into the AD9639 to approximately 0.8 V p-p
differential. This helps to prevent the large voltage swings of the
clock from feeding through to other portions of the AD9639,
and it preserves the fast rise and fall times of the signal, which
are critical to low jitter performance.
CMOS DRIVER
CLK+
0.1µF
ADC
AD9639
CLK
0.1µF
CLK–
0.1µF
39kΩ
*50Ω RESISTOR IS OPTIONAL.
Figure 46. Single-Ended 1.8 V CMOS Sample Clock
AD9510/AD9511/
AD9512/AD9513/
AD9514/AD9515/
ADT1-1WT, 1:1Z
0.1µF
50Ω*
AD9516/AD9518
0.1µF
0.1µF
CLK+
CLK
OPTIONAL
XFMR
CLK+
CLK+
100Ω
CMOS DRIVER
CLK
CLK+
ADC
AD9639
50Ω
0.1µF
0.1µF
0.1µF
ADC
AD9639
CLK–
0.1µF
SCHOTTKY
DIODES:
HSMS-2812
0.1µF
CLK–
*50Ω RESISTOR IS OPTIONAL.
Figure 43. Transformer-Coupled Differential Clock
Figure 47. Single-Ended 3.3 V CMOS Sample Clock
Another option is to ac-couple a differential PECL signal to the
sample clock input pins as shown in Figure 44. The AD9510/
AD9511/AD9512/AD9513/AD9514/AD9515/AD9516/AD9518
family of clock drivers offers excellent jitter performance.
Clock Duty Cycle Considerations
Typical high speed ADCs use both clock edges to generate a
variety of internal timing signals. As a result, these ADCs may
be sensitive to the clock duty cycle. Commonly, a 5% tolerance
is required on the clock duty cycle to maintain dynamic perfor-
mance characteristics.
AD9510/AD9511/
AD9512/AD9513/
AD9514/AD9515/
0.1µF
0.1µF
AD9516/AD9518
CLK+
CLK–
CLK
CLK+
ADC
AD9639
100Ω
The AD9639 contains a duty cycle stabilizer (DCS) that retimes
the nonsampling edge, providing an internal clock signal with a
nominal 50% duty cycle. This allows a wide range of clock input
duty cycles without affecting the performance of the AD9639.
When the DCS is on (default), noise and distortion performance
are nearly flat for a wide range of duty cycles. However, some
applications may require the DCS function to be off. If so, keep
in mind that the dynamic range performance may be affected
when operated in this mode. See the Memory Map section for
more details on using this feature.
PECL DRIVER
0.1µF
0.1µF
CLK–
CLK
240Ω
240Ω
50Ω*
50Ω*
*50Ω RESISTORS ARE OPTIONAL.
Figure 44. Differential PECL Sample Clock
AD9510/AD9511/
AD9512/AD9513/
AD9514/AD9515/
0.1µF
0.1µF
AD9516/AD9518
CLK+
CLK–
CLK
CLK+
ADC
AD9639
100Ω
LVDS DRIVER
CLK
0.1µF
0.1µF
Jitter in the rising edge of the input is an important concern,
and it is not reduced by the internal stabilization circuit. The
duty cycle control loop does not function for clock rates of less
than 50 MHz nominal. It is not recommended that this ADC
clock be dynamic in nature. Moving the clock around dynami-
cally requires long wait times for the back end serial capture to
retime and resynchronize to the receiving logic. This long time
constant far exceeds the time that it takes for the DCS and the
PLL to lock and stabilize. Only in rare applications would it be
necessary to disable the DCS circuitry in the clock register (see
Address 0x09 in Table 15). Keeping the DCS circuit enabled is
recommended to maximize ac performance.
CLK–
50Ω*
50Ω*
*50Ω RESISTORS ARE OPTIONAL.
Figure 45. Differential LVDS Sample Clock
In some applications, it is acceptable to drive the sample clock
inputs with a single-ended CMOS signal. In such applications,
CLK+ should be driven directly from a CMOS gate, and the
CLK− pin should be bypassed to ground with a 0.1 μF capacitor
in parallel with a 39 kΩ resistor (see Figure 46). Although the
Rev. B | Page 19 of 36
AD9639
Data Sheet
Clock Jitter Considerations
Power Dissipation
High speed, high resolution ADCs are sensitive to the quality of the
clock input. The degradation in SNR at a given input frequency (fA)
due only to aperture jitter (tJ) can be calculated as follows:
As shown in Figure 49 and Figure 50, the power dissipated by
the AD9639 is proportional to its clock rate. The digital power
dissipation does not vary significantly because it is determined
primarily by the DRVDD supply and the bias current of the
digital output drivers.
SNR Degradation = 20 × log 10(1/2 × π × fA × tJ)
In this equation, the rms aperture jitter represents the root mean
square of all jitter sources, including the clock input, analog input
signal, and ADC aperture jitter. IF undersampling applications
are particularly sensitive to jitter (see Figure 48).
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
0.8
0.7
0.6
The clock input should be treated as an analog signal in cases
where aperture jitter may affect the dynamic range of the AD9639.
Power supplies for clock drivers should be separated from the
ADC output driver supplies to avoid modulating the clock signal
with digital noise. Low jitter, crystal-controlled oscillators are
the best clock sources. If the clock is generated from another
type of source (by gating, dividing, or another method), it
should be retimed by the original clock during the last step.
I
AVDD
0.5
0.4
POWER
0.3
0.2
0.1
0
I
DRVDD
Refer to the AN-501 Application Note, the AN-756 Application
Note, and the Analog Dialogue article, “Analog-to-Digital Converter
Clock Optimization: A Test Engineering Perspective” (Volume 42,
Number 2, February 2008) for in-depth information about jitter
performance as it relates to ADCs (visit www.analog.com).
50
70
90
110
ENCODE (MSPS)
130
150
170
Figure 49. Supply Current vs. Encode for fIN = 84.3 MHz, fSAMPLE = 170 MSPS
130
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
0.8
0.7
0.6
RMS CLOCK JITTER REQUIREMENT
120
110
I
AVDD
16 BITS
14 BITS
12 BITS
100
90
80
70
60
50
40
30
0.5
0.4
POWER
0.3
0.2
0.1
0
10 BITS
0.125 ps
0.25 ps
0.5 ps
1.0 ps
2.0 ps
I
DRVDD
1
10
100
1000
50
70
90
110
130
150
170
190
210
ANALOG INPUT FREQUENCY (MHz)
ENCODE (MSPS)
Figure 50. Supply Current vs. Encode for fIN = 84.3 MHz, fSAMPLE = 210 MSPS
Figure 48. Ideal SNR vs. Input Frequency and Jitter
Rev. B | Page 20 of 36
Data Sheet
AD9639
The two resulting octets are optionally scrambled and encoded
into their corresponding 10-bit code. The scrambling function
is controlled by the JESD204 register, Address 0x033[0]. Figure 51
shows how the 12-bit data is taken from the ADC, the tail bits are
added, the two octets are scrambled, and the octets are encoded
into two 10-bit symbols. Figure 52 illustrates the data format.
DIGITAL OUTPUTS
Serial Data Frame
The AD9639 digital output complies with the JEDEC Standard
No. 204 (JESD204), which describes a serial interface for data
converters. JESD204 uses 8B/10B encoding as well as optional
scrambling. K28.5 and K28.7 comma symbols are used for frame
synchronization. The receiver is required to lock onto the serial
data stream and recover the clock with the use of a PLL. (Refer
to IEEE Std 802.3-2002, Section 3, for a complete 8B/10B and
comma symbol description.)
The scrambler uses a self-synchronizing polynomial-based
algorithm defined by the equation 1 + x14 + x15. The descrambler
in the receiver should be a self-synchronizing version of the
scrambler polynomial. A 16-bit parallel implementation is
shown in Figure 54.
The 8B/10B encoding works by taking eight bits of data (an
octet) and encoding them into a 10-bit symbol. In the AD9639,
the 12-bit converter word is broken into two octets. Bit 11
through Bit 4 are in the first octet. The second octet contains
Bit 3 through Bit 0 and four tail bits. The MSB of the tail bits can
also be used to indicate an out-of-range condition. The tail bits
are configured using the JESD204 register, Address 0x033[3].
Refer to JEDEC Standard No. 204-April 2006, Section 5.1, for
complete transport layer and data format details and Section 5.2
for a complete explanation of scrambling and descrambling.
DATA
FROM
ADC
FRAME
ASSEMBLER
(ADD TAIL BITS)
SCRAMBLER
14 15
8B/10B
ENCODER
TO
RECEIVER
1 + x + x
Figure 51. ADC Data Output Path
WORD 0[11:4]
SYMBOL 0[9:0]
FRAME 0
FRAME 1
WORD 0[3:0],TAIL BITS[3:0]
WORD 1[11:4]
SYMBOL 1[9:0]
SYMBOL 2[9:0]
SYMBOL 3[9:0]
TIME
WORD 1[3:0], TAIL BITS[3:0]
Figure 52. 12-Bit Data Transmission with Tail Bits
8B/10B
DECODER
DESCRAMBLER
14 15
FRAME
ALIGNMENT
DATA
OUT
FROM
TRANSMITTER
1 + x + x
Figure 53. Required Receiver Data Path
Rev. B | Page 21 of 36
AD9639
Data Sheet
S15
S14
S13
S12
S11
S10
S9
LSB
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
Q
S31
S30
S29
S28
S27
S26
S25
S24
S23
S22
S21
S20
S19
S18
CLK
LSB
D31
D30
D29
D28
D27
D26
D25
D24
D23
D22
D21
D20
D19
D18
D17
D16
Q
CLK
Q
CLK
S15
S14
S13
S12
S11
S10
S9
Q
CLK
Q
CLK
Q
CLK
Q
CLK
S8
Q
MSB
LSB
CLK
S7
CLK = FRAME CLK
Q
CLK
S6
Q
CLK
S8
S5
Q
CLK
S7
S4
Q
CLK
S6
S3
Q
CLK
S5
S2
Q
CLK
S4
S1
Q
S17
S16
CLK
S3
MSB
S2
MSB
S1
Figure 54. Parallel Descrambler Required in Receiver
Rev. B | Page 22 of 36
Data Sheet
AD9639
Initial Synchronization
To minimize skew and time misalignment between each channel
of the digital outputs, the following actions should be taken to
ensure that each channel data frame is within 1 clock cycle of
the sample clock. For some receiver logic, this is not required.
The serial interface must synchronize to the frame boundaries
before data can be properly decoded. The JESD204 standard has
a synchronization routine to identify the frame boundary. The
SYNC
SYNC
PGMx pins are used as
pins by default. When the
1. Full power-down through external PDWN pin.
2. Chip reset via external RESET pin.
3. Power-up by releasing external PDWN pin.
pin is taken low for at least two clock cycles, the AD9639 enters
the synchronization mode. The AD9639 transmits the K28.5
comma symbol until the receiver can identify the frame boundary.
SYNC
The receiver should then deassert the sync signal (take
high) and the ADC begins transmitting real data. The first non-
K28.5 symbol is the MSB symbol of the 12-bit data.
ICOUNTER = ‘0’;
VCOUNTER = ‘0’;
SYNC_REQUEST = ‘1’;
IF /K28.5/ AND /VALID/ THEN
KCOUNTER = KCOUNTER + ‘1’;
ELSE
RESET
INIT
KCOUNTER = ‘0’;
END IF;
KCOUNTER < 4
KCOUNTER = 4
ICOUNTER = ‘0’;
ICOUNTER = 3
SYNC_REQUEST = ‘0’;
VCOUNTER = ‘0’;
KCOUNTER = ‘0’;
IF /INVALID/ THEN
ICOUNTER = ICOUNTER + ‘1’;
VCOUNTER = ‘0’;
VCOUNTER = 4
ELSE IF /VALID/ THEN
VCOUNTER = VCOUNTER + ‘1’;
END IF;
CHECK
DATA
/VALID/
/INVALID/
VCOUNTER < 4 AND ICOUNTER < 3
Figure 55. Receiver State Machine
Table 8. Variables Used in Receiver State Machine
Variable
Description
ICOUNTER
/INVALID/
/K28.5/
Counter used in the CHECK phase to count the number of invalid symbols.
Asserted by receiver to indicate that the current symbol is an invalid symbol given the current running disparity.
Asserted when the current symbol corresponds to the K28.5 control character.
KCOUNTER
SYNC_REQUEST
/VALID/
Counter used in the INIT phase to count the number of valid K28.5 symbols.
Asserted by receiver when loss of code group synchronization is detected.
Asserted by receiver to indicate that the current symbol is a valid symbol given the current running disparity.
Counter used in the CHECK phase to count the number of successive valid symbols.
VCOUNTER
Rev. B | Page 23 of 36
AD9639
Data Sheet
Continuous Synchronization
When scrambling is enabled, any D28.7 symbols found in the
LSB octet of a frame are replaced with K28.7 comma symbols.
The receiver is responsible for replacing the K28.7 comma
symbols with D28.7 symbols when in this mode.
Continuous synchronization is part of the JESD204 specification.
The 12-bit word requires two octets to transmit all the data. The
two octets (MSB and LSB) are called a frame. When scrambling
is disabled and the LSB octets of two consecutive frames are the
same, the second LSB octet is replaced by a K28.7 comma symbol.
The receiver is responsible for replacing the K28.7 comma
symbol with the LSB octet of the previous frame.
By looking for K28.7 symbols, the receiver can ensure that it is
still synchronized to the frame boundary.
IF /K28.7/
/REPLACE_K28.7/
IF (OCOUNTER == PREVIOUS_POSITION) AND /VALID/
/RESET_OCTET_COUNTER/
END IF;
IF /VALID/ | (OCOUNTER == N-1)
PREVIOUS_POSITION = OCOUNTER
END IF;
END IF;
Figure 56. Pseudocode for Data Dependent Frame Synchronization in Receiver
Table 9. Variables and Functions in Data Dependent Frame Synchronization
Variable
Description
N
Number of octets in frame (octet indexing starts from 0).
/K28.7/
Asserted when the current symbol corresponds to the K28.7 control character.
Counter used to mark the position of the current octet in the frame.
Variable that stores the position in the frame of a K28.7 symbol.
Replace K28.7 at the decoder output as follows. When scrambling is disabled, replace K28.7 with the LSB
octet that was decoded at the same position in the previous frame; when scrambling is enabled, replace
K28.7 at the decoder output with D28.7.
OCOUNTER
PREVIOUS_POSITION
/REPLACE_K28.7/
/RESET_OCTET_COUNTER/ Reset octet counter to 0 at reception of next octet.
/VALID/ Asserted by receiver to indicate that the current symbol is a valid symbol given the current running disparity.
Rev. B | Page 24 of 36
Data Sheet
AD9639
If there is no far-end receiver termination or if there is poor
Digital Outputs and Timing
differential trace routing, timing errors may result. To avoid
such timing errors, it is recommended that the trace length be
less than 6 inches and that the differential output traces be close
together and at equal lengths.
The AD9639 has differential digital outputs that power up
by default. The driver current is derived on chip and sets the
output current at each output equal to a nominal 4 mA. Each
output presents a 100 Ω dynamic internal termination to reduce
unwanted reflections.
100Ω
DRVDD
DIFFERENTIAL
TRACE PAIR
A 100 Ω differential termination resistor should be placed at
each receiver input to result in a nominal 400 mV peak-to-peak
swing at the receiver. Alternatively, single-ended 50 Ω termina-
tion can be used. When single-ended termination is used, the
termination voltage should be DRVDD/2; otherwise, ac coupling
capacitors can be used to terminate to any single-ended voltage.
DOUT + x
RECEIVER
100Ω
DOUT – x
V
= DRVDD/2
OUTPUT SWING = 400mV p-p
CM
Figure 57. DC-Coupled Digital Output Termination Example
The AD9639 digital outputs can interface with custom ASICs
and FPGA receivers, providing superior switching performance
in noisy environments. Single point-to-point network topologies
are recommended with a single differential 100 Ω termination
resistor placed as close to the receiver logic as possible. The
common mode of the digital output automatically biases itself
to half the supply of DRVDD if dc-coupled connecting is used.
For receiver logic that is not within the bounds of the DRVDD
supply, an ac-coupled connection should be used. Simply place
a 0.1 μF capacitor on each output pin and derive a 100 Ω
differential termination close to the receiver side.
V
RXCM
100Ω
DIFFERENTIAL
TRACE PAIR
DRVDD
0.1µF
0.1µF
DOUT + x
RECEIVER
= Rx V
100Ω
OR
DOUT – x
V
OUTPUT SWING = 400mV p-p
CM
CM
Figure 58. AC-Coupled Digital Output Termination Example
Rev. B | Page 25 of 36
AD9639
Data Sheet
TJ@BERI: BATHTUB
HEIGHT1: EYE DIAGRAM
TIE1: HISTOGRAM
0
10
600
500
400
(y1) –375.023m
(y2) +409.847m
(∆y) +784.671m
1
2
3
600
+
+
+
–2
–4
–6
–8
10
10
10
10
400
200
300
200
100
0
0
–200
–400
–10
–12
–14
10
10
10
EYE: ALL BITS
OFFSET: 0.015
ULS: 5000: 40044, TOTAL: 12000: 80091
–600
–200
–100
0
100
200
–30
–10
10
30
–0.5
0
0.5
TIME (ps)
TIME (ps)
ULS
Figure 59. Digital Outputs Data Eye with Trace Lengths Less Than 6 Inches on Standard FR-4, External 100 Ω Terminations at Receiver
HEIGHT1: EYE DIAGRAM
(y1) –402.016m
(y2) +398.373m
(∆y) +800.389m
TIE1: HISTOGRAM
TJ@BERI: BATHTUB
0
10
300
250
200
1
2
3
600
400
+
+
+
–2
–4
–6
–8
10
10
10
10
200
0
150
100
50
–200
–400
–10
–12
–14
10
10
10
EYE: ALL BITS
OFFSET: 0.015
ULS: 5000: 40044, TOTAL 8000: 40044
–600
0
–200
–100
0
100
200
–50
0
50
–0.5
0
0.5
TIME (ps)
TIME (ps)
ULS
Figure 60. Digital Outputs Data Eye with Trace Lengths Greater Than 12 Inches on Standard FR-4, External 100 Ω Terminations at Receiver
Figure 59 shows an example of the digital output (default) data
eye and a time interval error (TIE) jitter histogram with trace
lengths less than 6 inches on standard FR-4 material. Figure 60
shows an example of trace lengths exceeding 12 inches on stan-
dard FR-4 material. Note that the TIE jitter histogram reflects
the decrease of the data eye opening as the edge deviates from
the ideal position. It is the user’s responsibility to determine
whether the waveforms meet the timing budget of the design
when the trace lengths exceed 6 inches.
The format of the output data is offset binary by default.
Table 10 provides an example of this output coding format.
To change the output data format to twos complement or gray
code, see the Memory Map section (Address 0x14 in Table 15).
Table 10. Digital Output Coding
(VIN + x) − (VIN − x),
Input Span = 1.25 V p-p (V) Binary ([D11:D0])
Digital Output Offset
Code
4095
2048
2047
0
+0.625
0.00
−0.000305
−0.625
1111 1111 1111
1000 0000 0000
0111 1111 1111
0000 0000 0000
Additional SPI options allow the user to further increase the
output driver voltage swing of all four outputs to drive longer
trace lengths (see Address 0x15 in Table 15). Even though this
produces sharper rise and fall times on the data edges and is less
prone to bit errors, the power dissipation of the DRVDD supply
increases when this option is used. See the Memory Map section
for more details.
The lowest typical clock rate is 100 MSPS. For clock rates slower
than 100 MSPS, the user can set Bit 3 to 0 in the serial control
register (Address 0x21 in Table 15). This option allows the user
to adjust the PLL loop bandwidth to use clock rates as low as
50 MSPS.
Rev. B | Page 26 of 36
Data Sheet
AD9639
Setting Bit 2 in the output mode register (Address 0x14) allows
the user to invert the digital outputs from their nominal state.
This is not to be confused with inverting the serial stream to an
LSB first mode. In default mode, as shown in Figure 2, the MSB
is first in the data output serial stream. However, this order can
be inverted so that the LSB is first in the data output serial stream.
The PN sequence long pattern produces a pseudorandom bit
sequence that repeats itself every 223 − 1 (8,388,607) bits. A
description of the PN sequence long and how it is generated can
be found in Section 5.6 of the ITU-T O.150 (05/96) standard.
The only differences are that the starting value must be a specific
value instead of all 1s (see Table 11 for the initial values) and
that the AD9639 inverts the bit stream with relation to the ITU-T
standard.
There are eight digital output test pattern options available that
can be initiated through the SPI (see Table 12 for the output bit
sequencing options). This feature is useful when validating
receiver capture and timing. Some test patterns have two serial
sequential words and can be alternated in various ways, depending
on the test pattern selected. Note that some patterns do not
adhere to the data format select option. In addition, custom
user-defined test patterns can be assigned in the user pattern
registers (Address 0x19 through Address 0x20).
Table 11. PN Sequence
Initial
Value
First Three Output Samples
(MSB First)
Sequence
PN Sequence Short 0x0DF
PN Sequence Long
0xDF9, 0x353, 0x301
0x29B80A 0x591, 0xFD7, 0x0A3
Consult the Memory Map section for information on how to
change these additional digital output timing features through
the SPI.
The PN sequence short pattern produces a pseudorandom bit
sequence that repeats itself every 29 − 1 (511) bits. A description
of the PN sequence short and how it is generated can be found
in Section 5.1 of the ITU-T O.150 (05/96) recommendation.
The only difference is that the starting value must be a specific
value instead of all 1s (see Table 11 for the initial values).
Table 12. Flexible Output Test Modes
Output Test Mode
Bit Sequence
Subject to Data
Format Select
Pattern Name
Digital Output Word 1
N/A
Digital Output Word 2
0000
0001
0010
0011
0100
0101
0110
0111
Off (default)
Midscale short
N/A
Same
Same
Same
0101 0101 0101
N/A
N/A
Yes
Yes
Yes
Yes
No
Yes
Yes
No
1000 0000 0000
1111 1111 1111
0000 0000 0000
1010 1010 1010
N/A
+Full-scale short
−Full-scale short
Checkerboard
PN sequence long1
PN sequence short1
One-/zero-word toggle
N/A
1111 1111 1111
0000 0000 0000
1 All test mode options except PN sequence long and PN sequence short can support 8- to 14-bit word lengths to verify data capture to the receiver.
Rev. B | Page 27 of 36
AD9639
Data Sheet
TEMPOUT Pin
the power-down feature is enabled, the chip continues to function
after PDWN is pulled low without requiring a reset. The AD9639
returns to normal operating mode when the PDWN pin is pulled
low. This pin is only 1.8 V tolerant.
The TEMPOUT pin can be used as a coarse temperature sensor
to monitor the internal die temperature of the device. This pin
typically has a 737 mV output with a clock rate of 210 MSPS
and a negative going temperature coefficient of −1.12 mV/°C.
The voltage response of this pin is characterized in Figure 61.
0.85
SDO Pin
The SDO pin is for use in applications that require a 4-wire SPI
mode operation. For normal operation, it should be tied low to
AGND through a 10 kΩ resistor. Alternatively, the device pin
can be left open, and the 345 Ω internal pull-down resistor pulls
this pin low. This pin is only 1.8 V tolerant.
0.83
0.81
0.79
0.77
0.75
0.73
0.71
0.69
SDI/SDIO Pin
The SDI/SDIO pin is for use in applications that require either a
4- or 3-wire SPI mode operation. For normal operation, it should
be tied low to AGND through a 10 kΩ resistor. Alternatively,
the device pin can be left open, and the 30 kΩ internal pull-
down resistor pulls this pin low. This pin is only 1.8 V tolerant.
0.67
0.65
SCLK Pin
–40 –30 –20 –10
0
10 20 30 40 50 60 70 80
TEMPERATURE (°C)
For normal operation, the SCLK pin should be tied to AGND
through a 10 kΩ resistor. Alternatively, the device pin can be left
open, and the 30 kΩ internal pull-down resistor pulls this pin
low. This pin is only 1.8 V tolerant.
Figure 61. TEMPOUT Pin Voltage vs. Temperature
RBIAS Pin
To set the internal core bias current of the ADC, place a resistor
(nominally equal to 10.0 kΩ) between ground and the RBIAS pin.
The resistor current is derived on chip and sets the AVDD current
of the ADC to a nominal 610 mA at 210 MSPS. Therefore, it is
imperative that a 1% or less tolerance on this resistor be used to
achieve consistent performance.
CSB Pin
For normal operation, the CSB pin should be tied high to AVDD
through a 10 kΩ resistor. Alternatively, the device pin can be left
open, and the 26 kΩ internal pull-up resistor pulls this pin high.
Tying the CSB pin to AVDD causes all information on the SCLK
and SDI/SDIO pins to be ignored. Tying the CSB pin low causes
all information on the SDO and SDI/SDIO pins to be written to
the device. This feature allows the user to reduce the number of
traces to the device if necessary. This pin is only 1.8 V tolerant.
VCM x Pins
The common-mode output pins can be enabled through the SPI
to provide an external reference bias voltage of 1.4 V for driving
the VIN + x/VIN − x analog inputs. The VCM x pins may be
required when connecting external devices, such as an amplifier
or transformer, to interface to the analog inputs.
PGMx Pins
All PGMx pins are automatically initialized as synchronization
pins by default. These pins are used to lock the FPGA timing and
data capture during initial startup. These pins are respective to
each channel (PGM3 = Channel A, PGM2 = Channel B, and so
on). The sync (PGMx) pin should be pulled high until this pin
receives a low signal input from the receiver, during which time
the ADC outputs K28.5 comma symbols to indicate the frame
boundary. When the receiver finds the frame boundary, the
sync identification is deasserted low and the ADC outputs the
valid data on the next packet boundary.
RESET Pin
The RESET pin resets the datapath and sets all SPI registers to
their default values. To use this pin, the user must resynchronize
the digital outputs. This pin is only 1.8 V tolerant.
PDWN Pin
When asserted high, the PDWN pin turns off all ADC channels,
including the output drivers. This function can be changed to
a standby function (see Address 0x08 in Table 15). This feature
allows the user to place all channels into standby mode. The
output drivers transmit pseudorandom data until the outputs
are disabled using the output mode register (Address 0x14).
When steady state operation for the device is achieved, these pins
can be assigned as a standby option using the PGM mode register
(Address 0x53 in Table 15). All other PGMx pins become global
synchronization pins. This pin is only 1.8 V tolerant.
When the PDWN pin is asserted high, the AD9639 is placed into
power-down mode, shutting down the reference, reference buffer,
PLL, and biasing networks. In this state, the ADC typically
dissipates 3 mW. If any of the SPI features are changed before
Rev. B | Page 28 of 36
Data Sheet
AD9639
SERIAL PORT INTERFACE (SPI)
The AD9639 serial port interface allows the user to configure the
converter for specific functions or operations through a structured
register space provided in the ADC. The SPI can provide the
user with additional flexibility and customization, depending
on the application. Addresses are accessed via the serial port
and can be written to or read from via the port. Memory is
organized into bytes that can be further divided into fields, as
documented in the Memory Map section. Detailed operational
information can be found in the Analog Devices, Inc., AN-877
Application Note, Interfacing to High Speed ADCs via SPI.
additional instructions. Regardless of the mode, if CSB is taken
high in the middle of a byte transfer, the SPI state machine is
reset and the device waits for a new instruction.
In addition to the operation modes, the SPI port configuration
influences how the AD9639 operates. For applications that do
not require a control port, the CSB line can be tied high. This
places the SDI/SDIO pin into its secondary mode, as defined in
the SDI/SDIO Pin section. CSB can also be tied low to enable
2-wire mode. When CSB is tied low, SCLK and SDI/SDIO are
the only pins required for communication. Although the device
is synchronized during power-up, the user should ensure that
the serial port remains synchronized with the CSB line when
using this mode. When operating in 2-wire mode, it is recom-
mended that a 1-, 2-, or 3-byte transfer be used exclusively.
Without an active CSB line, streaming mode can be entered but
not exited.
Four pins define the SPI: SCLK, SDI/SDIO, SDO, and CSB (see
Table 13). The SCLK pin is used to synchronize the read and
write data presented to the ADC. The SDI/SDIO pin is a dual-
purpose pin that allows data to be sent to and read from the
internal ADC memory map registers. The SDO pin is used in
4-wire mode to read back data from the part. The CSB pin is an
active low control that enables or disables the read and write cycles.
In addition to word length, the instruction phase determines
whether the serial frame is a read or write operation, allowing
the serial port to be used to both program the chip and read the
contents of the on-chip memory. If the instruction is a readback
operation, performing a readback causes the SDI/SDIO pin to
change from an input to an output at the appropriate point in
the serial frame.
Table 13. Serial Port Pins
Pin
Function
SCLK
Serial clock. Serial shift clock input. SCLK is used to
synchronize serial interface reads and writes.
SDI/SDIO Serial data input/output. Dual-purpose pin that
typically serves as an input or an output, depending
on the SPI wire mode, the instruction sent, and the
relative position in the timing frame.
Data can be sent in MSB first or LSB first mode. MSB first mode
is the default at power-up and can be changed by adjusting the
configuration register (Address 0x00). For more information
about this and other features, see the AN-877 Application Note,
Interfacing to High Speed ADCs via SPI.
SDO
Serial data output. Used only in 4-wire SPI mode.
When set, the SDO pin becomes active. When cleared,
the SDO pin remains in three-state and all read data
is routed to the SDI/SDIO pin.
CSB
Chip select bar (active low). This control gates the
read and write cycles.
HARDWARE INTERFACE
The pins described in Table 13 constitute the physical interface
between the user’s programming device and the serial port of
the AD9639. The SCLK and CSB pins function as inputs when
using the SPI. The SDI/SDIO pin is bidirectional, functioning as
an input during write phases and as an output during readback.
The falling edge of CSB in conjunction with the rising edge of
SCLK determines the start of the framing sequence. During the
instruction phase, a 16-bit instruction is transmitted, followed
by one or more data bytes, which is determined by Bit Field W0
and Bit Field W1. An example of the serial timing and its defini-
tions can be found in Figure 63 and Table 14.
If multiple SDI/SDIO pins share a common connection, ensure
that proper VOH levels are met. Assuming the same load for each
AD9639, Figure 62 shows the number of SDI/SDIO pins that
can be connected together and the resulting VOH level. This
interface is flexible enough to be controlled by either serial
PROMs or PIC microcontrollers, providing the user with an
alternative method, other than a full SPI controller, to program
the ADC (see the AN-812 Application Note).
During normal operation, CSB is used to signal to the device
that SPI commands are to be received and processed. When
CSB is brought low, the device processes SCLK and SDI/SDIO
to execute instructions. Normally, CSB remains low until the
communication cycle is complete. However, if connected to a
slow device, CSB can be brought high between bytes, allowing
older microcontrollers enough time to transfer data into shift
registers. CSB can be stalled when transferring one, two, or three
bytes of data. When W0 and W1 are set to 11, the device enters
streaming mode and continues to process data, either reading
or writing, until CSB is taken high to end the communication
cycle. This allows complete memory transfers without requiring
For users who wish to operate the ADC without using the
SPI, remove any connections from the CSB, SCLK, SDO, and
SDI/SDIO pins. By disconnecting these pins from the control bus,
the ADC can function in its most basic operation. Each of these
pins has an internal termination that floats to its respective level.
Rev. B | Page 29 of 36
AD9639
Data Sheet
1.800
1.795
1.790
1.785
1.780
1.775
1.770
1.765
1.760
1.755
1.750
1.745
1.740
1.735
1.730
1.725
1.720
1.715
0
10
20
30
40
50
60
70
80
90
100
NUMBER OF SDI/SDIO PINS CONNECTED TOGETHER
Figure 62. SDI/SDIO Pin Loading
tDS
tHIGH
tCLK
tH
tS
tDH
tLOW
CSB
DON’T
SCLK
DON’T
CARE
CARE
SDI/
SDIO
DON’T
CARE
DON’T
D0
R/W
W1
W0
A12
A11
A10
A9
A8
A7
D5
D4
D3
D2
D1
CARE
Figure 63. Serial Timing Details
Table 14. Serial Timing Definitions
Parameter
Timing (ns min)
Description
tDS
tDH
tCLK
tS
5
2
40
5
Setup time between the data and the rising edge of SCLK
Hold time between the data and the rising edge of SCLK
Period of the clock
Setup time between CSB and SCLK
tH
2
Hold time between CSB and SCLK
tHIGH
tLOW
tEN_SDI/SDIO
16
16
10
Minimum period that SCLK should be in a logic high state
Minimum period that SCLK should be in a logic low state
Minimum time for the SDI/SDIO pin to switch from an input to an output relative to the
SCLK falling edge (not shown in Figure 63)
tDIS_SDI/SDIO
10
Minimum time for the SDI/SDIO pin to switch from an output to an input relative to the
SCLK rising edge (not shown in Figure 63)
Rev. B | Page 30 of 36
Data Sheet
AD9639
MEMORY MAP
READING THE MEMORY MAP TABLE
RESERVED LOCATIONS
Undefined memory locations should not be written to except
when writing the default values suggested in this data sheet.
Blank cells in Table 15 should be considered reserved bits and
have a 0 written into their registers during power-up.
Each row in the memory map register table (Table 15) has eight
bit locations. The memory map is divided into three sections: the
chip configuration registers (Address 0x00 to Address 0x02),
the device index and transfer registers (Address 0x05 and
Address 0xFF), and the ADC function registers (Address 0x08
to Address 0x53).
DEFAULT VALUES
When the AD9639 comes out of a reset, critical registers are
preloaded with default values. These values are indicated in
Table 15.
The leftmost column of the memory map indicates the register
address; the default value is shown in the second rightmost
column. The Bit 7 column is the start of the default hexadecimal
value given. For example, Address 0x09, the clock register, has a
default value of 0x01, meaning that Bit 7 = 0, Bit 6 = 0, Bit 5 = 0,
Bit 4 = 0, Bit 3 = 0, Bit 2 = 0, Bit 1 = 0, and Bit 0 = 1, or 0000 0001
in binary. This setting is the default for the duty cycle stabilizer
in the on condition. By writing a 0 to Bit 0 of this address, fol-
lowed by 0x01 in the device update register (Address 0xFF[0],
the transfer bit), the duty cycle stabilizer is turned off. It is
important to follow each write sequence with a transfer bit to
update the SPI registers. For more information about this and
other functions, consult the AN-877 Application Note,
Interfacing to High Speed ADCs via SPI.
LOGIC LEVELS
In Table 15, “bit is set” is synonymous with “bit is set to Logic 1”
or “writing Logic 1 for the bit.” Similarly, “bit is cleared” is synon-
ymous with “bit is set to Logic 0” or “writing Logic 0 for the bit.”
Rev. B | Page 31 of 36
AD9639
Data Sheet
Table 15. Memory Map Register
Default
Addr. Register
(Hex) Name
(MSB)
Bit 7
(LSB)
Bit 0
Value
(Hex)
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Comments
Chip Configuration Registers
0x00
chip_port_
config (local,
master)
SDO active
(not
required,
ignored if
not used)
LSB
first
Soft
reset
16-bit
0x18
address
(default
mode for
ADCs)
0x01
0x02
chip_id
(global)
8-bit chip ID, Bits[2:0]
0x29: AD9639, 12-bit quad
Read only.
Read only.
chip_grade
(global)
Speed grade
010 = 170 MSPS
100 = 210 MSPS
Device Index and Transfer Registers
0x05
device_
index_A
(global)
ADC A
ADC B
ADC C
ADC D
0x0F
Bits are set to
determine
which device
on chip
receives the
next write
command.
The default
is all devices
on chip.
0xFF
device_
SW
0x00
Synchro-
update (local,
master)
transfer
1 = on
0 = off
(default)
nously
transfers
data from
the master
shift register
to the slave.
ADC Function Registers
0x08
0x09
0x0D
Modes
(local)
External PDWN pin
function
00 = full power-down
(default)
Power-down mode
00 = chip run
(default)
01 = full power-down
10 = standby
11 = reset
0x00
0x01
0x00
Determines
generic
modes
of chip
operation.
01 = standby
Clock
(global)
Duty
cycle
stabilize
1 = on
(default)
0 = off
Turns the
internal
duty cycle
stabilizer
on and off.
test_io
(local)
Reset PN
sequence sequence
long gen
1 = on
0 = off
Reset PN
Flexible output test mode
0000 = off (normal operation)
0001 = midscale short
0010 = +FS short
When set,
the test data
is placed on
the output
pins in place
of normal
data.
short gen
1 = on
0 = off
0011 = −FS short
(default)
(default)
0100 = checkerboard output
0101 = PN 23 sequence
0110 = PN 9 sequence
0111 = 1/0 word toggle
0x0E
0x0F
test_bist
(local)
BIST init
1 = on
0 = off
BIST
enable
1 = on
0 = off
(default)
0x00
0x00
When Bit 0
is set, the
built-in self-
test function
is initiated.
(default)
adc_input
(local)
Analog
disconnect enable
VCM
enable
1 = on
1 = on
0 = off
0 = off
(default)
(default)
Rev. B | Page 32 of 36
Data Sheet
AD9639
Default
Value
(Hex)
Addr. Register
(Hex) Name
(MSB)
Bit 7
(LSB)
Bit 0
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Comments
0x10
Offset
(local)
6-bit device offset adjustment[5:0]
011111 = +31 LSB
011110 = +30 LSB
011101 = +29 LSB
…
0x00
Device
offset trim.
000010 = +2 LSB
000001 = +1 LSB
000000 = 0 LSB
111111 = −1 LSB
111110 = −2 LSB
111101 = −3 LSB
…
100001 = −31 LSB
100000 = −32 LSB
0x14
0x15
0x18
output_mode
(local/global)
Output
enable bar
(local)
1 = off
0 = on
Output
invert
enable
(global)
1 = on
0 = off
(default)
Data format select
(global)
00 = offset binary
(default)
01 = twos
complement
10 = gray code
0x00
0x00
0x00
Configures
the outputs
and the
format of
the data.
(default)
output_adjust
(global)
Output driver
current[1:0]
00 = 400 mV
(default)
01 = 500 mV
10 = 440 mV
11 = 320 mV
VCM output
adjustments.
VREF
Ref_Vfs[4:0]
Select
(global)
Reference full-scale adjust
10000 = 0.98 V p-p
10001 = 1.00 V p-p
10010 = 1.02 V p-p
10011 = 1.04 V p-p
…
adjustments
for VREF
.
11111 = 1.23 V p-p
00000 = 1.25 V p-p
00001 = 1.27 V p-p
…
01110 = 1.48 V p-p
01111 = 1.5 V p-p
0x19
0x1A
0x1B
0x1C
0x1D
0x1E
0x1F
0x20
user_
patt1_lsb
(local)
B7
B6
B5
B4
B3
B2
B1
B9
B1
B9
B1
B9
B1
B9
B0
B8
B0
B8
B0
B8
B0
B8
0xAA
0xAA
0xAA
0xAA
0xAA
0xAA
0xAA
0xCC
User-Defined
Pattern 1
LSB.
user_
patt1_msb
(local)
B15
B7
B14
B6
B13
B5
B12
B4
B11
B3
B10
B2
User-Defined
Pattern 1
MSB.
user_
patt2_lsb
(local)
User-Defined
Pattern 2
LSB.
user_
patt2_msb
(local)
B15
B7
B14
B6
B13
B5
B12
B4
B11
B3
B10
B2
User-Defined
Pattern 2
MSB.
user_
patt3_lsb
(local)
User-Defined
Pattern 3
LSB.
user_
patt3_msb
(local)
B15
B7
B14
B6
B13
B5
B12
B4
B11
B3
B10
B2
User-Defined
Pattern 3
MSB.
user_
patt4_lsb
(local)
User-Defined
Pattern 4
LSB.
user_
patt4_msb
(local)
B15
B14
B13
B12
B11
B10
User-Defined
Pattern 4
MSB.
Rev. B | Page 33 of 36
AD9639
Data Sheet
Default
Addr. Register
(Hex) Name
(MSB)
Bit 7
(LSB)
Bit 0
Value
(Hex)
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Comments
0x21
serial_control
(global)
PLL
high
0x08
Serial stream
control.
encode
rate
mode
(global)
0 = low
rate
1 = high
rate
(default)
0x24
0x25
0x33
misr_lsb
(local)
B7
B6
B5
B4
B3
B2
B1
B9
B0
B8
0x00
0x00
0x00
Least
significant
byte of
MISR.
Read only.
misr_msb
(local)
B15
B14
B13
B12
B11
B10
Most
significant
byte of
MISR.
Read only.
JESD204
(global)
Over-
range in
LSB of
tail bits
0 = over-
range
disabled
(default)
1 = over-
range
Scram-
bling
enable
0 = scram-
bling
disabled
(default)
1 = scram-
bling
enabled
enabled
0x50
0x51
coarse_
gain_adj
(local)
Gain adjust
enable
1 = on
0 = off
(default)
Coarse gain adjust[5:0] = output[63:0]
000000 = 0000…0001
000001 = 0000…0011
000010 = 0000…0111
…
111101 = 0011…1111
111110 = 0111…1111
111111 = 1111…1111
0x00
0x00
fine_
gain_adj
(local)
Fine gain adjust[3:0] = output[15:0]
0000 = 0000000000000001
0001 = 0000000000000010
0010 = 0000000000000100
…
1101 = 0010000000000000
1110 = 0100000000000000
1111 = 1000000000000000
0x52
0x53
gain_cal_ctl
Temperature
sensor
enable
1 = on
0 = off
Gain
quarter
LSB
1 = on
0 = off
(default)
Gain cal
resetb
1 = on
(default)
0 = off
Gain cal
enable
1 = on
0 = off
(default)
0x02
0x00
(default)
Dynamic
pgm pins
(global)
pgm_3
00 = sync
01 = Standby A
10 = Standby A and
Standby D
pgm_2
00 = sync
01 = Standby B
10 = Standby B and
Standby C
pgm_1
00 = sync
pgm_0
00 = sync
01 = Standby D
10 = Standby D and
Standby A
Standby =
ADC core
off, PN23
enabled,
serial
01 = Standby C
10 = Standby C and
Standby B
11 = Standby A and
Standby B
11 = Standby B and
Standby A
11 = Standby C and
Standby D
11 = Standby D and
Standby C
channel
enabled.
Rev. B | Page 34 of 36
Data Sheet
AD9639
APPLICATIONS INFORMATION
POWER AND GROUND RECOMMENDATIONS
EXPOSED PADDLE THERMAL HEAT SLUG
RECOMMENDATIONS
When connecting power to the AD9639, it is recommended
that two separate 1.8 V supplies be used: one for analog (AVDD)
and one for digital (DRVDD). If only one supply is available, it
should be routed to the AVDD pin first and then tapped off and
isolated with a ferrite bead or a filter choke preceded by decou-
pling capacitors for the DRVDD pin. Several different decoupling
capacitors can be used to cover both high and low frequencies.
Locate these capacitors close to the point of entry at the PCB
level and close to the parts, with minimal trace lengths.
It is required that the exposed paddle on the underside of the
ADC be connected to analog ground (AGND) to achieve the best
electrical and thermal performance of the AD9639. An exposed
continuous copper plane on the PCB should mate to the AD9639
exposed paddle, Pin 0. The copper plane should have several vias
to achieve the lowest possible resistive thermal path for heat
dissipation to flow through the bottom of the PCB. These vias
should be solder-filled or plugged with nonconductive epoxy.
A single PCB ground plane should be sufficient when using the
AD9639. With proper decoupling and smart partitioning of the
analog, digital, and clock sections of the PCB, optimum perfor-
mance can easily be achieved.
To maximize the coverage and adhesion between the ADC and
PCB, partition the continuous copper plane into several uniform
sections by overlaying a silkscreen on the PCB. This provides
several tie points between the ADC and PCB during the reflow
process, whereas using one continuous plane with no partitions
guarantees only one tie point. See Figure 64 for a PCB layout
example. For detailed information on packaging and the PCB
layout of chip scale packages, see the AN-772 Application Note,
A Design and Manufacturing Guide for the Lead Frame Chip
Scale Package (LFCSP), at www.analog.com.
SILKSCREEN PARTITION
PIN 1 INDICATOR
Figure 64. Typical PCB Layout
Rev. B | Page 35 of 36
AD9639
Data Sheet
OUTLINE DIMENSIONS
10.10
10.00 SQ
9.90
0.60
0.42
0.24
0.30
0.23
0.18
0.60
0.42
0.24
PIN 1
INDICATOR
55
54
72
1
PIN 1
INDICATOR
9.85
0.50
BSC
9.75 SQ
9.65
8.35
8.20 SQ
8.05
EXPOSED
PAD
0.50
0.40
0.30
18
37
36
19
0.25 MIN
TOP VIEW
BOTTOM VIEW
8.50 REF
0.80 MAX
0.65 TYP
12° MAX
1.00
0.85
0.80
0.05 MAX
0.02 NOM
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
COPLANARITY
0.08
SEATING
PLANE
0.20 REF
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-VNND-4
Figure 65. 72-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
10 mm × 10 mm Body, Very Thin Quad
(CP-72-3)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
Temperature Range
Package Description
Package Option
CP-72-3
CP-72-3
CP-72-3
CP-72-3
AD9639BCPZ-170
AD9639BCPZRL-170
AD9639BCPZ-210
AD9639BCPZRL-210
AD9639-210KITZ
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
72-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
72-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
72-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
72-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
Evaluation Board
1 Z = RoHS Compliant Part.
©2009–2013 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D07973-0-7/13(B)
Rev. B | Page 36 of 36
相关型号：
AD9640ABCPZ-105
2-CH 14-BIT FLASH METHOD ADC, PARALLEL ACCESS, QCC64, 9 X 9 MM, ROHS COMPLIANT, MO-220VMMD-4, LFCSP-64
ROCHESTER
AD9640ABCPZ-125
2-CH 14-BIT FLASH METHOD ADC, PARALLEL ACCESS, QCC64, 9 X 9 MM, ROHS COMPLIANT, MO-220VMMD-4, LFCSP-64
ROCHESTER
©2020 ICPDF网 联系我们和版权申明