AD9958_08 [ADI]
2-Channel, 500 MSPS DDS with 10-Bit DACs; 2通道, 500 MSPS DDS 10位DAC型号: | AD9958_08 |
厂家: | ADI |
描述: | 2-Channel, 500 MSPS DDS with 10-Bit DACs |
文件: | 总44页 (文件大小:660K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
2-Channel, 500 MSPS DDS
with 10-Bit DACs
AD9958
FEATURES
APPLICATIONS
2 synchronized DDS channels @ 500 MSPS
Independent frequency/phase/amplitude control between
channels
Agile local oscillators
Phased array radars/sonars
Instrumentation
Matched latencies for frequency/phase/amplitude changes
Excellent channel-to-channel isolation (>72 dB)
Linear frequency/phase/amplitude sweeping capability
Up to 16 levels of frequency/phase/amplitude modulation
(pin-selectable)
Synchronized clocking
RF source for AOTF
Single-side band suppressed carriers
Quadrature communications
2 integrated 10-bit digital-to-analog converters (DACs)
Individually programmable DAC full-scale currents
0.12 Hz or better frequency tuning resolution
14-bit phase offset resolution
10-bit output amplitude scaling resolution
Serial I/O port interface (SPI) with 800 Mbps data throughput
Software-/hardware-controlled power-down
Dual supply operation (1.8 V DDS core/3.3 V serial I/O)
Multiple device synchronization
Selectable 4× to 20× REFCLK multiplier (PLL)
Selectable REFCLK crystal oscillator
56-lead LFCSP
FUNCTIONAL BLOCK DIAGRAM
10-BIT
DAC
RECONSTRUCTED
SINE WAVE
AD9958
(2)
500MSPS
10-BIT
DAC
RECONSTRUCTED
SINE WAVE
DDS CORES
MODULATION CONTROL
SYSTEM
CLOCK
SOURCE
TIMING AND
CONTROL
REF CLOCK
INPUT CIRCUITRY
USER INTERFACE
Figure 1.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 www.analog.com
Fax: 781.461.3113 © 2005–2008 Analog Devices, Inc. All rights reserved.
AD9958
TABLE OF CONTENTS
Features .............................................................................................. 1
Linear Sweep Mode.................................................................... 25
Linear Sweep No-Dwell Mode ................................................. 26
Sweep and Phase Accumulator Clearing Functions.............. 27
Output Amplitude Control Mode............................................ 28
Synchronizing Multiple AD9958 Devices................................... 29
Automatic Mode Synchronization........................................... 29
Manual Software Mode Synchronization................................ 29
Manual Hardware Mode Synchronization.............................. 29
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description......................................................................... 3
Specifications..................................................................................... 4
Absolute Maximum Ratings............................................................ 8
ESD Caution.................................................................................. 8
Pin Configuration and Function Descriptions............................. 9
Typical Performance Characteristics ........................................... 11
Application Circuits ....................................................................... 14
Equivalent Input and Output Circuits......................................... 17
Theory of Operation ...................................................................... 18
DDS Core..................................................................................... 18
Digital-to-Analog Converter .................................................... 18
Modes of Operation ....................................................................... 19
Channel Constraint Guidelines................................................ 19
Power Supplies ............................................................................ 19
Single-Tone Mode ...................................................................... 19
Reference Clock Modes ............................................................. 20
Scalable DAC Reference Current Control Mode ................... 21
Power-Down Functions............................................................. 21
Modulation Mode....................................................................... 21
Modulation Using SDIO_x Pins for RU/RD........................... 24
I/O_UPDATE, SYNC_CLK, and System Clock
Relationships............................................................................... 30
Serial I/O Port................................................................................. 31
Overview ..................................................................................... 31
Instruction Byte Description .................................................... 32
Serial I/O Port Pin Description................................................ 32
Serial I/O Port Function Description...................................... 32
MSB/LSB Transfer Description ................................................ 32
Serial I/O Modes of Operation................................................. 33
Register Maps and Bit Descriptions............................................. 36
Register Maps.............................................................................. 36
Descriptions for Control Registers .......................................... 39
Descriptions for Channel Registers ......................................... 41
Outline Dimensions....................................................................... 44
Ordering Guide .......................................................................... 44
REVISION HISTORY
7/08—Rev. 0 to Rev. A
Added Table 25; Renumbered Sequentially................................ 31
Changes to Figure 41...................................................................... 31
Changes to Figure 42, Serial Data I/O (SDIO_0, SDIO_1,
SDIO_3) Section, and Added Example Instruction Byte
Section.............................................................................................. 32
Added Table 27 ............................................................................... 33
Changes to Figure 46, Figure 47, Figure 48, and Figure 49....... 35
Changes to Register Maps and Bit Descriptions Section and
Added Endnote 2 to Table 28........................................................ 36
Added Endnote 1 to Table 30........................................................ 38
Added Exposed Pad Notation to Outline Dimensions ............. 44
Changes to Features.......................................................................... 1
Inserted Figure 1; Renumbered Sequentially................................ 1
Changes to Input Level Parameter in Table 1 ............................... 4
Added Profile Pin Toggle Rate Parameter in Table 1................... 6
Changes to Layout ............................................................................ 8
Changes to Table 3............................................................................ 9
Added Equivalent Input and Output Circuits Section .............. 17
Changes to Reference Clock Input Circuitry Section................ 20
Change to Figure 35 ....................................................................... 21
Changes to Setting the Slope of the Linear Sweep Section ....... 25
Changes to Figure 37...................................................................... 26
Changes to Figure 38 and Figure 39............................................. 27
Changes to Figure 40...................................................................... 30
9/05—Revision 0: Initial Version
Rev. A | Page 2 of 44
AD9958
GENERAL DESCRIPTION
The AD9958 consists of two DDS cores that provide indepen-
dent frequency, phase, and amplitude control on each channel.
This flexibility can be used to correct imbalances between
signals due to analog processing, such as filtering, amplification,
or PCB layout related mismatches. Because both channels share
a common system clock, they are inherently synchronized.
Synchronization of multiple devices is supported.
The DAC outputs are supply referenced and must be termin-
ated into AVDD by a resistor or an AVDD center-tapped
transformer. Each DAC has its own programmable reference to
enable different full-scale currents for each channel.
The DDS acts as a high resolution frequency divider with the
REFCLK as the input and the DAC providing the output. The
REFCLK input source is common to both channels and can be
driven directly or used in combination with an integrated
REFCLK multiplier (PLL) up to a maximum of 500 MSPS. The
PLL multiplication factor is programmable from 4 to 20, in
integer steps. The REFCLK input also features an oscillator
circuit to support an external crystal as the REFCLK source.
The crystal must be between 20 MHz and 30 MHz. The crystal
can be used in combination with the REFCLK multiplier.
The AD9958 can perform up to a 16-level modulation of
frequency, phase, or amplitude (FSK, PSK, ASK). Modulation is
performed by applying data to the profile pins. In addition, the
AD9958 also supports linear sweep of frequency, phase, or
amplitude for applications such as radar and instrumentation.
The AD9958 serial I/O port offers multiple configurations to
provide significant flexibility. The serial I/O port offers an SPI-
compatible mode of operation that is virtually identical to the
SPI operation found in earlier Analog Devices, Inc., DDS
products. Flexibility is provided by four data pins (SDIO_0/
SDIO_1/SDIO_2/SDIO_3) that allow four programmable
modes of serial I/O operation.
The AD9958 comes in a space-saving 56-lead LFCSP package.
The DDS core (AVDD and DVDD pins) is powered by a 1.8 V
supply. The digital I/O interface (SPI) operates at 3.3 V and
requires the pin labeled DVDD_I/O (Pin 49) be connected
to 3.3 V.
The AD9958 uses advanced DDS technology that provides low
power dissipation with high performance. The device incorporates
two integrated, high speed 10-bit DACs with excellent wideband
and narrow-band SFDR. Each channel has a dedicated 32-bit
frequency tuning word, 14 bits of phase offset, and a 10-bit
output scale multiplier.
The AD9958 operates over the industrial temperature range of
−40°C to +85°C.
AD9958
DDS CORE
COS(X)
CH0_IOUT
CH0_IOUT
Σ
Σ
Σ
Σ
Σ
DAC
DAC
32
32
32
32
15
10
10
10
10
DDS CORE
COS(X)
CH1_IOUT
CH1_IOUT
Σ
15
SCALABLE
DAC REF
CURRENT
DAC_RSET
32
PHASE/
ΔPHASE
14
AMP/
ΔAMP
10
FTW
ΔFTW
SYNC_IN
SYNC_OUT
I/O_UPDATE
TIMING AND CONTROL LOGIC
PWR_DWN_CTL
MASTER_RESET
SYSTEM
CLK
CONTROL
÷4
SYNC_CLK
REGISTERS
SCLK
CS
REF CLOCK
MULTIPLIER
4× TO 20×
REF_CLK
REF_CLK
I/O
MUX
CHANN
EL
PORT
SDIO_0
SDIO_1
SDIO_2
SDIO_3
REGISTE
RS
BUFFER
BUFFER/
XTAL
OSCILLATOR
PROFILE
REGISTERS
1.8V
1.8V
AVDD
DVDD
P0 P1 P2 P3
DVDD_I/O
CLK_MODE_SEL
Figure 2. Detailed Block Diagram
Rev. A | Page 3 of 44
AD9958
SPECIFICATIONS
AVDD and DVDD = 1.8 V 5ꢀ; DVDD_I/O = 3.3 V 5ꢀ; T = 25°C; RSET = 1.91 kΩ; external reference clock frequency = 500 MSPS
(REFCLK multiplier bypassed), unless otherwise noted.
Table 1.
Parameter
Min
Typ
Max
Unit
Test Conditions/Comments
REFERENCE CLOCK INPUT CHARACTERISTICS
Frequency Range
See Figure 34 and Figure 35
REFCLK Multiplier Bypassed
REFCLK Multiplier Enabled
Internal VCO Output Frequency Range
VCO Gain Control Bit Set High1
VCO Gain Control Bit Set Low1
Crystal REFCLK Source Range
Input Level
Input Voltage Bias Level
Input Capacitance
Input Impedance
1
10
500
125
MHz
MHz
255
100
20
500
160
30
MHz
MHz
MHz
mV
V
200
1000
Measured at each pin (single-ended)
1.15
2
1500
pF
Ω
Duty Cycle with REFCLK Multiplier Bypassed
Duty Cycle with REFCLK Multiplier Enabled
CLK Mode Select (Pin 24) Logic 1 Voltage
CLK Mode Select (Pin 24) Logic 0 Voltage
DAC OUTPUT CHARACTERISTICS
Resolution
Full-Scale Output Current
Gain Error
Channel-to-Channel Output Amplitude Matching Error
Output Current Offset
45
35
1.25
55
65
1.8
0.5
%
%
V
V
1.8 V digital input logic
1.8 V digital input logic
Must be referenced to AVDD
10
10
+10
+2.5
25
Bits
mA
% FS
%
μA
LSB
LSB
pF
1.25
−10
−2.5
1
Differential Nonlinearity
Integral Nonlinearity
Output Capacitance
0.5
1.0
3
Voltage Compliance Range
AVDD −
0.50
AVDD +
0.50
V
Channel-to-Channel Isolation
WIDEBAND SFDR
72
dB
DAC supplies tied together (see Figure 19)
The frequency range for wideband SFDR
is defined as dc to Nyquist
1 MHz to 20 MHz Analog Output
20 MHz to 60 MHz Analog Output
60 MHz to 100 MHz Analog Output
100 MHz to 150 MHz Analog Output
150 MHz to 200 MHz Analog Output
NARROW-BAND SFDR
−65
−62
−59
−56
−53
dBc
dBc
dBc
dBc
dBc
1.1 MHz Analog Output ( 10 kHz)
1.1 MHz Analog Output ( 50 kHz)
1.1 MHz Analog Output ( 250 kHz)
1.1 MHz Analog Output ( 1 MHz)
15.1 MHz Analog Output ( 10 kHz)
15.1 MHz Analog Output ( 50 kHz)
15.1 MHz Analog Output ( 250 kHz)
15.1 MHz Analog Output ( 1 MHz)
40.1 MHz Analog Output ( 10 kHz)
40.1 MHz Analog Output ( 50 kHz)
40.1 MHz Analog Output ( 250 kHz)
40.1 MHz Analog Output ( 1 MHz)
75.1 MHz Analog Output ( 10 kHz)
−90
−88
−86
−85
−90
−87
−85
−83
−90
−87
−84
−82
−87
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
Rev. A | Page 4 of 44
AD9958
Parameter
Min
Typ
−85
−83
−82
−87
−85
−83
−81
−87
−85
−83
−81
Max
Unit
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
Test Conditions/Comments
75.1 MHz Analog Output ( 50 kHz)
75.1 MHz Analog Output ( 250 kHz)
75.1 MHz Analog Output ( 1 MHz)
100.3 MHz Analog Output ( 10 kHz)
100.3 MHz Analog Output ( 50 kHz)
100.3 MHz Analog Output ( 250 kHz)
100.3 MHz Analog Output ( 1 MHz)
200.3 MHz Analog Output ( 10 kHz)
200.3 MHz Analog Output ( 50 kHz)
200.3 MHz Analog Output ( 250 kHz)
200.3 MHz Analog Output ( 1 MHz)
PHASE NOISE CHARACTERISTICS
Residual Phase Noise @ 15.1 MHz (fOUT
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
@ 1 MHz Offset
Residual Phase Noise @ 40.1 MHz (fOUT
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
@ 1 MHz Offset
Residual Phase Noise @ 75.1 MHz (fOUT
@ 1 kHz Offset
)
)
)
−150
−159
−165
−165
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−142
−151
−160
−162
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−135
−146
−154
−157
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
@ 10 kHz Offset
@ 100 kHz Offset
@ 1 MHz Offset
Residual Phase Noise @ 100.3 MHz (fOUT
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
@ 1 MHz Offset
)
−134
−144
−152
−154
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
Residual Phase Noise @ 15.1 MHz (fOUT) with REFCLK
Multiplier Enabled 5×
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
@ 1 MHz Offset
−139
−149
−153
−148
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
Residual Phase Noise @ 40.1 MHz (fOUT) with REFCLK
Multiplier Enabled 5×
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
@ 1 MHz Offset
−130
−140
−145
−139
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
Residual Phase Noise @ 75.1 MHz (fOUT) with REFCLK
Multiplier Enabled 5×
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
@ 1 MHz Offset
−123
−134
−138
−132
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
Residual Phase Noise @ 100.3 MHz (fOUT) with REFCLK
Multiplier Enabled 5×
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
@ 1 MHz Offset
−120
−130
−135
−129
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
Rev. A | Page 5 of 44
AD9958
Parameter
Min
Typ
Max
Unit
Test Conditions/Comments
Residual Phase Noise @ 15.1 MHz (fOUT) with REFCLK
Multiplier Enabled 20×
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
@ 1 MHz Offset
−127
−136
−139
−138
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
Residual Phase Noise @ 40.1 MHz (fOUT) with REFCLK
Multiplier Enabled 20×
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
@ 1 MHz Offset
−117
−128
−132
−130
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
Residual Phase Noise @ 75.1 MHz (fOUT) with REFCLK
Multiplier Enabled 20×
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
@ 1 MHz Offset
−110
−121
−125
−123
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
Residual Phase Noise @ 100.3 MHz (fOUT) with REFCLK
Multiplier Enabled 20×
@ 1 kHz Offset
@ 10 kHz Offset
@ 100 kHz Offset
@ 1 MHz Offset
−107
−119
−121
−119
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
SERIAL PORT TIMING CHARACTERISTICS
Maximum Frequency Serial Clock (SCLK)
200
MHz
ns
ns
ns
ns
Minimum SCLK Pulse Width Low (tPWL
)
1.6
2.2
2.2
0
Minimum SCLK Pulse Width High (tPWH
)
Minimum Data Setup Time (tDS
Minimum Data Hold Time
)
CS
Minimum Setup Time (tPRE
1.0
12
ns
)
Minimum Data Valid Time for Read Operation
MISCELLANEOUS TIMING CHARACTERISTICS
MASTER_RESET Minimum Pulse Width
ns
1
Min pulse width = 1 sync clock period
Min pulse width = 1 sync clock period
Rising edge to rising edge
I/O_UPDATE Minimum Pulse Width
1
4.8
0
5.4
0
2.5
0
Minimum Setup Time (I/O_UPDATE to SYNC_CLK)
Minimum Hold Time (I/O_UPDATE to SYNC_CLK)
Minimum Setup Time (Profile Inputs to SYNC_CLK)
Minimum Hold Time (Profile Inputs to SYNC_CLK)
Minimum Setup Time (SDIO Inputs to SYNC_CLK)
Minimum Hold Time (SDIO Inputs to SYNC_CLK)
Propagation Time Between REF_CLK and SYNC_CLK
Profile Pin Toggle Rate
ns
ns
ns
ns
ns
ns
ns
Rising edge to rising edge
2.25
3.5
5.5
2
Sync
clocks
CMOS LOGIC INPUTS
VIH
VIL
2.0
2.7
V
V
μA
μA
pF
0.8
12
Logic 1 Current
Logic 0 Current
Input Capacitance
CMOS LOGIC OUTPUTS
VOH
3
−12
2
1 mA load
V
V
VOL
0.4
Rev. A | Page 6 of 44
AD9958
Parameter
Min
Typ
Max
Unit
Test Conditions/Comments
POWER SUPPLY
Total Power Dissipation—Both Channels On, Single-
Tone Mode
Total Power Dissipation—Both Channels On, with
Sweep Accumulator
315
350
380
420
mW
mW
Dominated by supply variation
Dominated by supply variation
Total Power Dissipation—Full Power-Down
IAVDD—Both Channels On, Single-Tone Mode
IAVDD—Both Channels On, Sweep Accumulator,
REFCLK Multiplier, and 10-Bit Output Scalar
Enabled
13
90
95
mW
mA
mA
105
110
IDVDD—Both Channels On, Single-Tone Mode
60
70
70
80
mA
mA
IDVDD—Both Channels On, Sweep Accumulator,
REFCLK Multiplier, and 10-Bit Output Scalar
Enabled
IDVDD_I/O
22
30
2.5
2.5
mA
mA
mA
mA
IDVDD = read
IDVDD = write
IAVDD Power-Down Mode
IDVDD Power-Down Mode
DATA LATENCY (PIPELINE DELAY) SINGLE-TONE MODE2, 3
Frequency, Phase, and Amplitude Words to DAC
Output with Matched Latency Enabled
Frequency Word to DAC Output with Matched
Latency Disabled
Phase Offset Word to DAC Output with Matched
Latency Disabled
Amplitude Word to DAC Output with Matched
Latency Disabled
29
29
25
17
SYSCLKs
SYSCLKs
SYSCLKs
SYSCLKs
DATA LATENCY (PIPELINE DELAY) MODULATION MODE3, 4
Frequency Word to DAC Output
Phase Offset Word to DAC Output
Amplitude Word to DAC Output
34
29
21
SYSCLKs
SYSCLKs
SYSCLKs
DATA LATENCY (PIPELINE DELAY) LINEAR SWEEP MODE3, 4
Frequency Rising/Falling Delta-Tuning Word to DAC
Output
Phase Offset Rising/Falling Delta-Tuning Word to
DAC Output
Amplitude Rising/Falling Delta-Tuning Word to DAC
Output
41
37
29
SYSCLKs
SYSCLKs
SYSCLKs
1 For the VCO frequency range of 160 MHz to 255 MHz, there is no guarantee of operation.
2 Data latency is referenced to I/O_UPDATE.
3 Data latency is fixed.
4 Data latency is referenced to a profile change.
Rev. A | Page 7 of 44
AD9958
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
Maximum Junction Temperature
DVDD_I/O (Pin 49)
AVDD, DVDD
Digital Input Voltage (DVDD_I/O = 3.3 V)
Digital Output Current
Storage Temperature Range
Operating Temperature Range
Lead Temperature (10 sec Soldering)
θJA
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rating
150°C
4 V
2 V
−0.7 V to +4 V
5 mA
–65°C to +150°C
–40°C to +85°C
300°C
ESD CAUTION
21°C/W
2°C/W
θJC
Rev. A | Page 8 of 44
AD9958
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
SYNC_IN
SYNC_OUT
MASTER_RESET
PWR_DWN_CTL
AVDD
1
2
3
4
5
6
7
8
9
PIN 1
INDICATOR
42 P2
41 P1
40 P0
39 AVDD
38 NC
37 AVDD
36 AVDD
35 AVDD
34 NC
33 AVDD
32 NC
AD9958
AGND
AVDD
CH0_IOUT
CH0_IOUT
TOP VIEW
(Not to Scale)
AGND 10
AVDD 11
AGND 12
31 AVDD
30 AVDD
29 AVDD
CH1_IOUT 13
14
CH1_IOUT
NOTES
1. THE EXPOSED EPAD ON BOTTOM SIDE OF PACKAGE IS AN
ELECTRICAL CONNECTION AND MUST BE SOLDERED TO GROUND.
2. PIN 49 IS DVDD_I/O AND IS TIED TO 3.3V.
3. NC = NO CONNECT.
Figure 3. Pin Configuration
Table 3. Pin Function Descriptions
Pin No.
Mnemonic
I/O1
Description
1
SYNC_IN
I
Used to Synchronize Multiple AD9958 Devices. Connects to the SYNC_OUT pin of
the master AD9958 device.
2
3
SYNC_OUT
O
I
Used to Synchronize Multiple AD9958 Devices. Connects to the SYNC_IN pin of the
slave AD9958 devices.
Active High Reset Pin. Asserting the MASTER_RESET pin forces the AD9958 internal
registers to their default state, as described in the Register Maps and Bit Descriptions
section.
MASTER_RESET
4
PWR_DWN_CTL
AVDD
I
I
External Power-Down Control.
Analog Power Supply Pins (1.8 V).
5, 7, 11, 15, 19, 21,
26, 29, 30, 31, 33,
35, 36, 37, 39
6, 10, 12, 16, 18,
20, 25
AGND
I
Analog Ground Pins.
45, 55
44, 56
8
DVDD
DGND
I
I
Digital Power Supply Pins (1.8 V).
Digital Power Ground Pins.
True DAC Output. Terminates into AVDD.
Complementary DAC Output. Terminates into AVDD.
True DAC Output. Terminates into AVDD.
Complementary DAC Output. Terminates into AVDD.
CH0_IOUT
CH0_IOUT
CH1_IOUT
CH1_IOUT
DAC_RSET
O
O
O
O
I
9
13
14
17
Establishes the Reference Current for All DACs. A 1.91 kΩ resistor (nominal) is
connected from Pin 17 to AGND.
22
23
REF_CLK
REF_CLK
I
I
Complementary Reference Clock/Oscillator Input. When the REF_CLK is operated
in single-ended mode, this pin should be decoupled to AVDD or AGND with a
0.1 μF capacitor.
Reference Clock/Oscillator Input. When the REF_CLK is operated in single-ended
mode, this is the input. See the Modes of Operation section for the reference clock
configuration.
Rev. A | Page 9 of 44
AD9958
Pin No.
Mnemonic
I/O1
Description
24
CLK_MODE_SEL
I
Control Pin for the Oscillator Section. Caution: Do not drive this pin beyond 1.8 V.
When high (1.8 V), the oscillator section is enabled to accept a crystal as the
REF_CLK source. When low, the oscillator section is bypassed.
27
LOOP_FILTER
I
Connects to the external zero compensation network of the PLL loop filter.
Typically, the network consists of a 0 Ω resistor in series with a 680 pF capacitor
tied to AVDD.
28, 32, 34, 38
40, 41, 42, 43
NC
N/A
I
No Connection.
P0, P1, P2, P3
Data pins used for modulation (FSK, PSK, ASK), to start/stop for the sweep
accumulators, or used to ramp up/ramp down the output amplitude. The data is
synchronous to the SYNC_CLK (Pin 54). The data inputs must meet the setup and
hold time requirements to the SYNC_CLK. The functionality of these pins is
controlled by profile pin configuration (PPC) bits (FR1[14:12]).
46
I/O_UPDATE
I
A rising edge transfers data from the serial I/O port buffer to active registers.
I/O_UPDATE is synchronous to the SYNC_CLK (Pin 54). I/O_UPDATE must meet the
setup and hold time requirements to the SYNC_CLK to guarantee a fixed pipeline
delay of data to the DAC output; otherwise, a 1 SYNC_CLK period of pipeline
uncertainty exists. The minimum pulse width is one SYNC_CLK period.
47
48
CS
I
I
Active Low Chip Select. Allows multiple devices to share a common I/O bus (SPI).
SCLK
Serial Data Clock for I/O Operations. Data bits are written on the rising edge of
SCLK and read on the falling edge of SCLK.
49
50
51, 52, 53
DVDD_I/O
SDIO_0
SDIO_1, SDIO_2,
SDIO_3
I
3.3 V Digital Power Supply for SPI Port and Digital I/O.
Data Pin SDIO_0 is dedicated to the serial port I/O only.
Data Pin SDIO_1, Data Pin SDIO_2, and Data Pin SDIO_3 can be used for the serial
I/O port or used to initiate a ramp-up/ramp-down (RU/RD) of the DAC output
amplitude.
I/O
I/O
54
SYNC_CLK
O
The SYNC_CLK runs at one fourth the system clock rate. It can be disabled. I/O_UPDATE
or data (Pin 40 to Pin 43) is synchronous to the SYNC_CLK. To guarantee a fixed
pipeline delay of data to DAC output, I/O_UPDATE or data (Pin 40 to Pin 43) must
meet the setup and hold time requirements to the rising edge of SYNC_CLK;
otherwise, a 1 SYNC_CLK period of uncertainty exists.
1 I = input, O = output.
Rev. A | Page 10 of 44
AD9958
TYPICAL PERFORMANCE CHARACTERISTICS
REF LVL
0dBm
DELTA 1 (T1)
–69.47dB
30.06012024MHz SWT
RBW
VBW
20kHz
20kHz
1.6s
RF ATT
UNIT
20dB
DELTA 1 (T1)
–71.73dB
RBW
VBW
SWT
20kHz
20kHz
1.6s
RF ATT
UNIT
20dB
dB
REF LVL
0dBm
dB
4.50901804MHz
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
A
A
1
1AP
1AP
START 0Hz
25MHz/DIV
STOP 250MHz
START 0Hz
25MHz/DIV
STOP 250MHz
Figure 7. Wideband SFDR, fOUT = 15.1 MHz, fCLK = 500 MSPS
Figure 4. Wideband SFDR, fOUT = 1.1 MHz, fCLK = 500 MSPS
DELTA 1 (T1)
–62.84dB
40.08016032MHz SWT
RBW
VBW
20kHz
20kHz
1.6s
RF ATT
UNIT
20dB
dB
REF Lv]
0dBm
DELTA 1 (T1)
–60.13dB
75.15030060MHz SWT
RBW
VBW
20kHz
20kHz
1.6s
RF ATT
UNIT
20dB
dB
REF LVL
0dBm
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
1
A
A
1
1AP
1AP
START 0Hz
25MHz/DIV
STOP 250Hz
START 0Hz
25MHz/DIV
STOP 250MHz
Figure 5. Wideband SFDR, fOUT = 40.1 MHz, fCLK = 500 MSPS
Figure 8. Wideband SFDR, fOUT = 75.1 MHz, fCLK = 500 MSPS
DELTA 1 (T1)
–59.04dB
100.70140281MHz
RBW
VBW
SWT
20kHz
20kHz
1.6s
RF ATT
UNIT
20dB
dB
REF LVL
0dBm
DELTA 1 (T1)
–53.84dB
–101.20240481MHz SWT
RBW
VBW
20kHz
20kHz
1.6s
RF ATT
UNIT
20dB
dB
REF LVL
0dBm
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
A
A
1
1
1AP
1AP
START 0Hz
25MHz/DIV
STOP 250MHz
START 0Hz
25MHz/DIV
STOP 250MHz
Figure 6. Wideband SFDR, fOUT = 100.3 MHz, fCLK = 500 MSPS
Figure 9. Wideband SFDR, fOUT = 200.3 MHz, fCLK = 500 MSPS
Rev. A | Page 11 of 44
AD9958
REF LVL
0dBm
DELTA 1 (T1)
–84.73dB
254.50901604kHz
RBW
VBW
SWT
500Hz
500Hz
20s
RF ATT
UNIT
20dB
dB
REF LVL
0dBm
DELTA 1 (T1)
–84.86dB
–200.40080160kHz
RBW
VBW
SWT
500Hz
500Hz
20s
RF ATT
UNIT
20dB
dB
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
1
A
A
1
1AP
1AP
CENTER 1.1MHz
100kHz/DIV
SPAN 1MHz
CENTER 15.1MHz
100kHz/DIV
SPAN 1MHz
Figure 10. NBSFDR, fOUT = 1.1 MHz, fCLK = 500 MSPS, 1 MHz
Figure 13. NBSFDR, fOUT = 15.1 MHz, fCLK = 500 MSPS, 1 MHz
REF LVL
0dBm
DELTA 1 (T1)
–84.10dB
120.24048096kHz SWT
RBW
VBW
500Hz
500Hz
20s
RF ATT
UNIT
20dB
dB
REF LVL
0dBm
DELTA 1 (T1)
–86.03dB
262.56513026kHz
RBW
VBW
SWT
500Hz
500Hz
20s
RF ATT
UNIT
20dB
dB
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
1
A
A
1
1AP
1AP
CENTER 40.1MHz
100kHz/DIV
SPAN 1MHz
CENTER 75.1MHz
100kHz/DIV
SPAN 1MHz
Figure 11. NBSFDR, fOUT = 40.1 MHz, fCLK = 500 MSPS, 1 MHz
Figure 14. NBSFDR, fOUT = 75.1 MHz, fCLK = 500 MSPS, 1 MHz
REF LVL
0dBm
DELTA 1 (T1)
–83.72dB
–400.80160321kHz
RBW
VBW
SWT
500Hz
500Hz
20s
RF ATT
UNIT
20dB
dB
REF LVL
0dBm
DELTA 1 (T1)
–82.63dB
RBW
VBW
500Hz
500Hz
20s
RF ATT
UNIT
20dB
dB
400.80160321kHz SWT
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
A
A
1
1
1AP
1AP
CENTER 200.3MHz
100kHz/DIV
SPAN 1MHz
CENTER 100.3MHz
100kHz/DIV
SPAN 1MHz
Figure 15. NBSFDR fOUT = 200. 3MHz, fCLK = 500 MSPS, , 1 MHz
Figure 12. NBSFDR, fOUT = 100.3 MHz, fCLK = 500 MSPS, 1 MHz
Rev. A | Page 12 of 44
AD9958
–100
–110
–120
–130
–140
–150
–160
–170
–60
–65
–70
–75
–80
–85
75.1MHz
SINGLE DAC POWER PLANE
100.3MHz
40.1MHz
15.1MHz
1k
SEPARATED DAC POWER PLANES
10
100
10k
100k
1M
10M
25.3
50.3
75.3
100.3 125.3 150.3 175.3 200.3
FREQUENCY OF COUPLING SPUR (MHz)
FREQUENCY OFFSET (Hz)
Figure 16. Residual Phase Noise (SSB) with fOUT = 15.1 MHz, 40.1MHz,
75.1 MHz, 100.3 MHz; fCLK = 500 MHz with REFCLK Multiplier Bypassed
Figure 19. Channel Isolation at 500 MSPS Operation; Conditions are Channel
of Interest Fixed at 110.3 MHz, the Other Channels Are Frequency Swept
–70
–80
–90
600
500
–100
100.3MHz
400
–110
2 CHANNELS ON
300
75.1MHz
–120
1 CHANNEL ON
200
–130
–140
40.1MHz
–150
15.1MHz
100
0
–160
–170
10
100
1k
10k
100k
1M
10M
500
450
400
350
300
250
200
150
100
50
FREQUENCY OFFSET (Hz)
REFERENCE CLOCK FREQUENCY (MHz)
Figure 17. Residual Phase Noise (SSB) with fOUT = 15.1 MHz, 40.1MHz,
75.1 MHz, 100.3 MHz; fCLK = 500 MHz with REFCLK Multiplier = 5×
Figure 20. Power Dissipation vs. Reference Clock Frequency vs. Channel(s)
Power On/Off
–70
–80
–90
–45
–50
SFDR AVERAGED
–100
–110
–120
–130
–140
–150
–160
–170
100.3MHz
75.1MHz
–55
–60
–65
–70
–75
40.1MHz
15.1MHz
10
100
1k
10k
100k
1M
10M
1.1
15.1
40.1
75.1
100.3
200.3
FREQUENCY OFFSET (Hz)
fOUT (MHz)
Figure 18. Residual Phase Noise (SSB) with fOUT = 15.1 MHz, 40.1MHz,
75.1 MHz,100.3 MHz; fCLK = 500 MHz with REFCLK Multiplier = 20×
Figure 21. Averaged Channel SFDR vs. fOUT
Rev. A | Page 13 of 44
AD9958
APPLICATION CIRCUITS
PULSE
ANTENNA
RADIATING
ELEMENTS
AD9958
FILTER
FILTER
FILTER
FILTER
CH0
CH1
LO
REFCLK
Figure 22. Phase Array Radar Using Precision Frequency/Phase Control from DDS in FMCW or Pulsed Radar Applications;
DDS Provides Either Continuous Wave or Frequency Sweep
AD8348
AD8347
I BASEBAND
AD8346
ADL5390
AD8349
CH0
LO
PHASE
SPLITTER
RF OUTPUT
AD9958
CH1
REFCLK
Q BASEBAND
Figure 23. Single-Sideband-Suppressed Carrier Upconversion
AD9510, AD9511, ADF4106
÷
CHARGE
PUMP
LOOP
FILTER
PHASE
VCO
COMPARATOR
REFERENCE
÷
LPF
REFCLK
AD9958
Figure 24. DDS in PLL Locking to Reference Offering Distribution with Fine Frequency and Delay Adjust Tuning
Rev. A | Page 14 of 44
AD9958
AD9510
CLOCK DISTRIBUTOR
WITH
CLOCK
SOURCE
DELAY EQUALIZATION
REF_CLK
AD9510
SYNCHRONIZATION
DELAY EQUALIZATION
SYNC_OUT
C1
SYNC_IN
S1AD9958
DATA
A1
A2
A3
FPGA
FPGA
FPGA
FPGA
(MASTER)
SYNC_CLK
C2
DATA
S2AD9958
(SLAVE 1)
SYNC_CLK
CENTRAL
CONTROL
C3
S3AD9958
DATA
(SLAVE 2)
SYNC_CLK
C4
S4AD9958
DATA
A4
(SLAVE 3)
SYNC_CLK
A_END
Figure 25. Synchronizing Multiple Devices to Increase Channel Capacity Using the AD9510 as a Clock Distributor for the Reference and SYNC_CLK
OPTICAL FIBER CHANNEL
WITH MULTIPLE DISCRETE
WAVELENGTHS
WDM
SPLITTER
SOURCE
WDM SIGNAL
INPUTS
CH0
CH0
CH1
AMP
AMP
ACOUSTIC OPTICAL
TUNABLE FILTER
AD9958
CH1
REFCLK
OUTPUTS
CH0 CH1
SELECTABLE WAVELENGTH FROM EACH
CHANNEL VIA DDS TUNING AOTF
Figure 26. DDS Providing Stimulus for Acoustic Optical Tunable Filter
CH0
–
ADCMP563
AD9958
CH1
REFCLK
+
Figure 27. Agile Clock Source with Duty Cycle Control Using the Phase Offset Value in DDS to Change the DC Voltage to the Comparator
Rev. A | Page 15 of 44
AD9958
PROGRAMMABLE 1 TO 32
DIVIDER AND DELAY ADJUST
CLOCK OUTPUT
SELECTION(S)
AD9515
AD9514
LVPECL
LVDS
CH0
CH1
AD9513
n
CMOS
AD9512
AD9958
REFCLK
AD9515
AD9514
LVPECL
LVDS
CMOS
IMAGE
AD9513
n
AD9512
n = DEPENDENT ON
PRODUCT SELECTION
Figure 28. Clock Generation Circuit Using the AD9512/AD9513/AD9514/AD9515 Series of Clock Distribution Chips
Rev. A | Page 16 of 44
AD9958
EQUIVALENT INPUT AND OUTPUT CIRCUITS
DVDD_I/O = 3.3V
INPUT
OUTPUT
AVOID OVERDRIVING
DIGITAL INPUTS.
FORWARD BIASING
DIODES MAY COUPLE
DIGITAL NOISE ON
POWER PINS.
Figure 29. CMOS Digital Inputs
CHx_IOUT
CHx_IOUT
TERMINATE OUTPUTS
INTO AVDD. DO NOT
EXCEED VOLTAGE
COMPLIANCE OF
OUTPUTS.
Figure 30. DAC Outputs
AVDD
Z
Z
1.5kΩ
1.5kΩ
REF_CLK
AVDD
REF_CLK
AVDD
AMP
OSC
OSC
REF_CLK INPUTS ARE
INTERNALLY BIASED AND
NEED TO BE AC-COUPLED.
OSC INPUTS ARE DC-COUPLED.
REF_CLK
Figure 31. REF_CLK/
Inputs
Rev. A | Page 17 of 44
AD9958
THEORY OF OPERATION
DDS CORE
DIGITAL-TO-ANALOG CONVERTER
The AD9958 incorporates four 10-bit current output DACs.
The DAC converts a digital code (amplitude) into a discrete
analog quantity. The DAC current outputs can be modeled as a
current source with high output impedance (typically 100 kΩ).
Unlike many DACs, these current outputs require termination
into AVDD via a resistor or a center-tapped transformer for
expected current flow.
The AD9958 has two DDS cores, each consisting of a 32-bit
phase accumulator and phase-to-amplitude converter. Together,
these digital blocks generate a digital sine wave when the phase
accumulator is clocked and the phase increment value (frequency
tuning word) is greater than 0. The phase-to-amplitude converter
simultaneously translates phase information to amplitude
information by a cos(θ) operation.
Each DAC has complementary outputs that provide a combined
full-scale output current (IOUT + IOUT). The outputs always sink
The output frequency (fOUT) of each DDS channel is a function
of the rollover rate of each phase accumulator. The exact
relationship is given in the following equation:
current, and their sum equals the full-scale current at any point
in time. The full-scale current is controlled by means of an
external resistor (RSET) and the scalable DAC current control
bits discussed in the Modes of Operation section. The resistor,
RSET, is connected between the DAC_RSET pin and analog
ground (AGND). The full-scale current is inversely proportional
to the resistor value as follows:
(FTW)( fS )
fOUT
=
232
where:
fS is the system clock rate.
FTW is the frequency tuning word and is 0 ≤ FTW ≤ 231.
232 represents the phase accumulator capacity.
18.91
IOUT (max)
RSET
=
Because both channels share a common system clock, they are
inherently synchronized.
The maximum full-scale output current of the combined DAC
outputs is 15 mA, but limiting the output to 10 mA provides
optimal spurious-free dynamic range (SFDR) performance.
The DAC output voltage compliance range is AVDD + 0.5 V to
AVDD − 0.5 V. Voltages developed beyond this range may cause
excessive harmonic distortion. Proper attention should be paid
to the load termination to keep the output voltage within its
compliance range. Exceeding this range could potentially dam-
age the DAC output circuitry.
The DDS core architecture also supports the capability to phase
offset the output signal, which is performed by the channel
phase offset word (CPOW). The CPOW is a 14-bit register that
stores a phase offset value. This value is added to the output of
the phase accumulator to offset the current phase of the output
signal. Each channel has its own phase offset word register. This
feature can be used for placing all channels in a known phase
relationship relative to one another. The exact value of phase
offset is given by the following equation:
LPF
CHx_IOUT
1:1
POW
⎛
⎜
⎝
⎞
⎟
⎠
Φ =
× 360°
214
AVDD
DAC
50Ω
CHx_IOUT
Figure 32. Typical DAC Output Termination Configuration
Rev. A | Page 18 of 44
AD9958
MODES OF OPERATION
There are many combinations of modes (for example, single-
tone, modulation, linear sweep) that the AD9958 can perform
simultaneously. However, some modes require multiple data
pins, which can impose limitations. The following guidelines
can help determine if a specific combination of modes can be
performed simultaneously by the AD9958.
POWER SUPPLIES
The AVDD and DVDD supply pins provide power to the DDS
core and supporting analog circuitry. These pins connect to a
1.8 V nominal power supply.
The DVDD_I/O pin connects to a 3.3 V nominal power supply.
All digital inputs are 3.3 V logic except for the CLK_MODE_SEL
input. CLK_MODE_SEL (Pin 24) is an analog input and should
be operated by 1.8 V logic.
CHANNEL CONSTRAINT GUIDELINES
•
Single-tone mode, two-level modulation mode, and linear
sweep mode can be enabled on either channel and in any
combination simultaneously.
SINGLE-TONE MODE
Single-tone mode is the default mode of operation after a master
reset signal. In this mode, both DDS channels share a common
address location for the frequency tuning word (Register 0x04)
and phase offset word (Register 0x05). Channel enable bits are
provided in combination with these shared addresses. As a
result, the frequency tuning word and/or phase offset word can
be independently programmed between channels (see the follow-
ing Step 1 through Step 5). The channel enable bits do not
require an I/O update to enable or disable a channel.
•
•
Both channels can perform four-level modulation
simultaneously.
Either channel can perform eight-level or 16-level
modulation. The other channel can only be in single-tone
mode.
The RU/RD function can be used on both channels in
single-tone mode. See the Output Amplitude Control
Mode section for the RU/RD function.
When Profile Pin P2 and Profile Pin P3 are used for
RU/RD, either channel can perform two-level modulation
with RU/RD or both channels can perform linear
frequency or phase sweep with RU/RD.
•
•
See the Register Maps and Bit Descriptions section for a
description of the channel enable bits in the channel select
register (CSR, Register 0x00). The channel enable bits are
enabled or disabled immediately after the CSR data byte is
written.
•
•
When Profile Pin P3 is used for RU/RD, either channel can
be used in eight-level modulation with RU/RD. The other
channel can only be in single-tone mode.
Address sharing enables channels to be written simultaneously,
if desired. The default state enables all channel enable bits.
Therefore, the frequency tuning word and/or phase offset word
is common to all channels but written only once through the
serial I/O port.
When SDIO_1, SDIO_2, and SDIO_3 pins are used for
RU/RD, either or both channels can perform two-level
modulation with RU/RD. If one channel is not in two-level
modulation, it can only be in single-tone mode.
When the SDIO_1, SDIO_2, and SDIO_3 pins are used for
RU/RD, either or both channels can perform four-level
modulation with RU/RD. If one channel is not in four-level
modulation, it can only be in single-tone mode.
When the SDIO_1, SDIO_2, and SDIO_3 pins are used for
RU/RD, either channel can perform eight-level modulation
with RU/RD. The other channel can only be in single-tone
mode.
When the SDIO_1, SDIO_2, and SDIO_3 pins are used for
RU/RD, either channel can perform 16-level modulation with
RU/RD. The other channel can only be in single-tone mode.
Amplitude modulation, linear amplitude sweep modes,
and the RU/RD function cannot operate simultaneously,
but frequency and phase modulation can operate
simultaneously with the RU/RD function.
•
•
The following steps present a basic protocol to program a
different frequency tuning word and/or phase offset word for
each channel using the channel enable bits.
1. Power up the DUT and issue a master reset. A master reset
places the part in single-tone mode and single-bit mode for
serial programming operations (refer to the Serial I/O Modes
of Operation section). Frequency tuning words and phase
offset words default to 0 at this point.
•
•
2. Enable only one channel enable bit (Register 0x00) and
disable the other channel enable bit.
3. Using the serial I/O port, program the desired frequency
tuning word (Register 0x04) and/or the phase offset word
(Register 0x05) for the enabled channel.
4. Repeat Step 2 and Step 3 for each channel.
5. Send an I/O update signal. After an I/O update, all
channels should output their programmed frequency
and/or phase offset values.
Rev. A | Page 19 of 44
AD9958
The charge pump current in the PLL defaults to 75 μA. This
setting typically produces the best phase noise characteristics.
Increasing the charge pump current may degrade phase noise,
but it decreases the lock time and changes the loop bandwidth.
Single-Tone Mode—Matched Pipeline Delay
In single-tone mode, the AD9958 offers matched pipeline delay
to the DAC input for all frequency, phase, and amplitude changes.
This avoids having to deal with different pipeline delays between
the three input ports for such applications. The feature is enabled
by asserting the matched pipe delays active bit found in the
channel function register (CFR, Register 0x03). This feature
is available in single-tone mode only.
Enabling the on-chip oscillator for crystal operation is performed
by driving CLK_MODE_SEL (Pin 24) to logic high (1.8 V
logic). With the on-chip oscillator enabled, connection of an
REF_CLK
external crystal to the REF_CLK and
inputs is made,
producing a low frequency reference clock. The frequency of
the crystal must be in the range of 20 MHz to 30 MHz.
REFERENCE CLOCK MODES
The AD9958 supports multiple reference clock configurations
to generate the internal system clock. As an alternative to
clocking the part directly with a high frequency clock source,
the system clock can be generated using the internal, PLL-based
reference clock multiplier. An on-chip oscillator circuit is also
available for providing a low frequency reference signal by
connecting a crystal to the clock input pins. Enabling these
features allows the part to operate with a low frequency clock
source and still provide a high update rate for the DDS and
DAC. However, using the clock multiplier changes the output
phase noise characteristics. For best phase noise performance,
a clean, stable clock with a high slew is required (see Figure 17
and Figure 18).
Table 4 summarizes the clock modes of operation. See Table 1
for more details.
Reference Clock Input Circuitry
The reference clock input circuitry has two modes of operation
controlled by the logic state of Pin 24 (CLK_MODE_SEL). The
first mode (logic low) configures as an input buffer. In this
mode, the reference clock must be ac-coupled to the input due
to internal dc biasing. This mode supports either differential
or single-ended configurations. If single-ended mode is chosen,
the complementary reference clock input (Pin 22) should be
decoupled to AVDD or AGND via a 0.1 μF capacitor. Figure 33
to Figure 35 exemplify typical reference clock configurations for
the AD9958.
Enabling the PLL allows multiplication of the reference clock
frequency from 4× to 20×, in integer steps. The PLL multiplica-
tion value is represented by a 5-bit multiplier value. These bits
are located in Function Register 1 (FR1, Register 0x01), Bits[22:18]
(see the Register Maps and Bit Descriptions section).
1:1
BALUN
0.1µF
50Ω
0.1µF
REF_CLK
PIN 23
REFCLK
SOURCE
REF_CLK
PIN 22
When FR1[22:18] is programmed with values ranging from
4 to 20 (decimal), the clock multiplier is enabled. The integer
value in the register represents the multiplication factor. The
system clock rate with the clock multiplier enabled is equal to
the reference clock rate multiplied by the multiplication factor.
If FR1[22:18] is programmed with a value less than 4 or greater
than 20, the clock multiplier is disabled and the multiplication
factor is effectively 1.
Figure 33. Differential Coupling from Single-Ended Source
The reference clock inputs can also support an LVPECL or
PECL driver as the reference clock source.
0.1µF
REF_CLK
PIN 23
LVPECL/
PECL
TERMINATION
DRIVER
REF_CLK
PIN 22
0.1µF
Figure 34. Differential Clock Source Hook-Up
Whenever the PLL clock multiplier is enabled or the multiplica-
tion value is changed, time should be allowed to lock the PLL
(typically 1 ms).
The second mode of operation (Pin 24 = logic high = 1.8 V)
provides an internal oscillator for crystal operation. In this
mode, both clock inputs are dc-coupled via the crystal leads
and are bypassed. The range of crystal frequencies supported is
from 20 MHz to 30 MHz. Figure 35 shows the configuration
for using a crystal.
Note that the output frequency of the PLL is restricted to a
frequency range of 100 MHz to 500 MHz. However, there is a
VCO gain control bit that must be used appropriately. The VCO
gain control bit defines two ranges (low/high) of frequency
output. The VCO gain control bit defaults to low (see Table 1
for details).
Table 4. Clock Configuration
CLK_MODE_SEL, Pin 24 FR1[22:18] PLL Divider Ratio = M
Crystal Oscillator Enabled
System Clock (fSYSCLK
)
Min/Max Freq. Range (MHz)
100 < fSYSCLK < 500
20 < fSYSCLK < 30
100 < fSYSCLK < 500
0 < fSYSCLK < 500
High = 1.8 V Logic
High = 1.8 V Logic
Low
4 ≤ M ≤ 20
M < 4 or M > 20
4 ≤ M ≤ 20
Yes
Yes
No
No
fSYSCLK = fOSC × M
fSYSCLK = fOSC
fSYSCLK = fREFCLK × M
fSYSCLK = fREFCLK
Low
M < 4 or M > 20
Rev. A | Page 20 of 44
AD9958
When FR1[6] = 1 and the PWR_DWN_CTL input pin is high,
the AD9958 is put into full power-down mode. In this mode, all
functions are powered down. This includes the DAC and PLL,
which take a significant amount of time to power up. When the
PLL is bypassed, the PLL is shut down to conserve power.
39pF
39pF
REF_CLK
PIN 23
25MHz
XTAL
REF_CLK
PIN 22
When the PWR_DWN_CTL input pin is high, the individual
power-down bits (CFR[7:6]) and (FR1[7]) are invalid (don’t
care) and unused. When the PWR_DWN_CTL input pin is low,
the individual power-down bits control the power-down modes
of operation.
Figure 35. Crystal Input Configuration
SCALABLE DAC REFERENCE CURRENT CONTROL
MODE
RSET is common to all four DACs. As a result, the full-scale
currents are equal by default. The scalable DAC reference can
be used to set the full-scale current of each DAC independent
from one another. This is accomplished by using the register
bits CFR[9:8]. Table 5 shows how each DAC can be individually
scaled for independent channel control. This scaling provides
for binary attenuation.
Note that the power-down signals are all designed such that
Logic 1 indicates the low power mode and Logic 0 indicates the
powered-up mode.
MODULATION MODE
The AD9958 can perform 2-/4-/8-/16-level modulation of
frequency, phase, or amplitude. Modulation is achieved by
applying data to the profile pins. Each channel can be program-
med separately, but the ability to modulate multiple channels
simultaneously is constrained by the limited number of profile
pins. For instance, 16-level modulation uses all four profile pins,
which inhibits modulation for the remaining channel.
Table 5. DAC Full-Scale Current Control
CFR[9:8]
LSB Current State
11
01
10
00
Full scale
Half scale
Quarter scale
Eighth scale
In addition, the AD9958 has the ability to ramp up or ramp
down the output amplitude before, during, or after a modulation
(FSK, PSK only) sequence. This is performed by using the 10-bit
output scalar. If the RU/RD feature is desired, unused profile
pins or unused SDIO_1/SDIO_2/SDIO_3 pins can be confi-
gured to initiate the operation. See the Output Amplitude
Control Mode section for more details of the RU/RD feature.
POWER-DOWN FUNCTIONS
The AD9958 supports an externally controlled power-down
feature and the more common software programmable power-
down bits found in previous Analog Devices DDS products.
The software control power-down allows the input clock circui-
try, the DAC, and the digital logic (for each separate channel) to
be individually powered down via unique control bits (CFR[7:6]).
These bits are not active when the externally controlled power-
down pin (PWR_DWN_CTL) is high. When the input pin,
PWR_DWN_CTL, is high, the AD9958 enters a power-down
mode based on the FR1[6] bit. When the PWR_DWN_CTL
input pin is low, the external power-down control is inactive.
In modulation mode, each channel has its own set of control
bits to determine the type (frequency, phase, or amplitude)
of modulation. Each channel has 16 profile (channel word)
registers for flexibility. Register 0x0A through Register 0x18
are profile registers for modulation of frequency, phase, or
amplitude. Register 0x04, Register 0x05, and Register 0x06
are dedicated registers for frequency, phase, and amplitude,
respectively. These registers contain the first frequency, phase
offset, and amplitude word.
When FR1[6] = 0 and the PWR_DWN_CTL input pin is high,
the AD9958 is put into a fast recovery power-down mode. In
this mode, the digital logic and the DAC digital logic are powered
down. The DAC bias circuitry, PLL, oscillator, and clock input
circuitry are not powered down.
Frequency modulation has 32-bit resolution, phase modulation is
14 bits, and amplitude is 10 bits. When modulating phase or
amplitude, the word value must be MSB aligned in the profile
(channel word) registers and the unused bits are don’t care bits.
Rev. A | Page 21 of 44
AD9958
In modulation mode, the amplitude frequency phase (AFP)
select bits (CFR[23:22]) and modulation level bits (FR1[9:8])
are programmed to configure the modulation type and level
(see Table 6 and Table 7). Note that the linear sweep enable bit
must be set to Logic 0 in direct modulation mode.
If the profile pins are used for RU/RD, Logic 0 is for ramp-up
and Logic 1 is for ramp-down.
Because of the two channels and limited data pins, it is
necessary to assign the profile pins and/or SDIO_1, SDIO_2,
and SDIO_3 pins to a dedicated channel. This is controlled by
the profile pin configuration (PPC) bits (FR1[14:12]). Each of the
following modulation descriptions incorporates data pin
assignments.
Table 6. Modulation Type Configuration
AFP Select
(CFR[23:22])
Linear Sweep Enable
(CFR[14])
Description
00
01
10
11
X
0
0
0
Modulation disabled
Amplitude modulation
Frequency modulation
Phase modulation
Two-Level Modulation—No RU/RD
The modulation level bits (FR1[9:8]) are set to 00 (two-level).
The AFP select bits (CFR[23:22]) are set to the desired modulation
type. The RU/RD bits (FR1[11:10]) and the linear sweep enable
bit (CFR[14]) are disabled. Table 9 displays how the profile pins
and channels are assigned.
Table 7. Modulation Level Selection
Modulation Level (FR1[9:8])
Description
00
01
10
11
Two-level modulation
Four-level modulation
Eight-level modulation
16-level modulation
As shown in Table 9, only Profile Pin P2 can be used to modulate
Channel 0. If frequency modulation is selected and Profile Pin P2
is Logic 0, Channel Frequency Tuning Word 0 (Register 0x04) is
chosen; if Profile Pin P2 is Logic 1, Channel Word 1 (Register
0x0A) is chosen.
When modulating, the RU/RD function can be limited based
on pins available for controlling the feature. The SDIO_x pins
are for RU/RD only, not for modulation.
Four-Level Modulation—No RU/RD
The modulation level bits are set to 01 (four-level). The AFP
select bits (CFR[23:22]) are set to the desired modulation type.
The RU/RD bits (FR1[11:10]) and the linear sweep enable bit
(CFR[14]) are disabled. Table 10 displays how the profile pins
and channels are assigned to each other.
Table 8. RU/RD Profile Pin Assignments
Ramp-Up/Ramp-Down
(RU/RD) (FR1[11:10])
Description
00
01
RU/RD disabled
Only Profile Pin P2 and Profile Pin P3
available for RU/RD operation
Only Profile Pin P3 available for RU/RD
operation
Only SDIO_1, SDIO_2, and SDIO_3
pins available for RU/RD operation;
this forces the serial I/O to be used
only in 1-bit mode
For the conditions in Table 10, the profile (channel word)
register chosen is based on the 2-bit value presented to Profile
Pins [P0:P1] or Profile Pins [P2:P3].
10
11
For example, if PPC = 101, [P0:P1] = 11, and [P2:P3] = 01, then
the contents of the Channel Word 3 register of Channel 0 are
presented to the output of Channel 0 and the contents of the
Channel Word 1 register of Channel 1 are presented to the
output of Channel 1.
Table 9. Profile Pin Channel Assignments
Profile Pin Configuration (PPC) (FR1[14:12])
XXX
P0
P1
P2
P3
Description
N/A
N/A
CH0
CH1
Two-level modulation, both channels, no RU/RD
Table 10. Profile Pin and Channel Assignments
Profile Pin Configuration (PPC) (FR1[14:12])
P0
P1
P2
P3
Description
101
CH0
CH0
CH1
CH1
Four-level modulation on CH0 and CH1, no RU/RD
Rev. A | Page 22 of 44
AD9958
Eight-Level Modulation—No RU/RD
For the conditions in Table 12, the profile register chosen is
based on the 4-bit value presented to Profile Pins [P0:P3]. For
example, if PPC = X11 and [P0:P3] = 1110, the contents of the
Channel Word 14 register of Channel 1 is presented to the
output of Channel 1.
The modulation level bits (FR1[9:8]) are set to 10 (eight-level).
The AFP select bits (CFR[23:22]) are set to a nonzero value.
The RU/RD bits (FR1[11:10]) and the linear sweep enable bit
(CFR[14]) are disabled. Note that the AFP select bits of the
other channel not being used must be set to 00. Table 11 shows
the assignment of profile pins and channels.
Two-Level Modulation Using Profile Pins for RU/RD
When the RU/RD bits = 01, Profile Pin P2 and Profile Pin P3
are available for RU/RD. Note that only a modulation level of
two is available in this mode. See Table 13 for available pin
assignments.
For the condition in Table 11, the choice of channel word registers
is based on the 3-bit value presented to Profile Pins [P0:P2]. For
example, if PPC = X10 and [P0:P2] = 111, the contents of the
Channel Word 7 register of Channel 0 are presented to the output
Channel 0.
Eight-Level Modulation Using a Profile Pin for RU/RD
When the RU/RD bits = 10, Profile Pin P3 is available for
RU/RD. Note that only a modulation level of eight is available
in this mode. See Table 14 for available pin assignments.
16-Level Modulation—No RU/RD
The modulation level bits (FR1[9:8]) are set to 11 (16-level).
The AFP select bits (CFR[23:22]) are set to the desired modulation
type. The RU/RD bits (FR1[11:10]) and the linear sweep enable
bit (CFR[14]) are disabled. The AFP select bits of the other channel
not being used must be set to 00. Table 12 displays how the profile
pins and channels are assigned.
Table 11. Profile Pin and Channel Assignments for Eight-Level Modulation (No RU/RD)
Profile Pin Config. (PPC)
(FR1[14:12])
P0
P1
P2
P3
X
X
Description
X10
X11
CH0
CH1
CH0
CH1
CH0
CH1
Eight-level modulation on CH0, no RU/RD
Eight-level modulation on CH1, no RU/RD
Table 12. Profile Pin and Channel Assignments for 16-Level Modulation (No RU/RD)
Profile Pin Config. (PPC)
(FR1[14:12])
P0
P1
P2
P3
Description
X10
X11
CH0
CH1
CH0
CH1
CH0
CH1
CH0
CH1
16-level modulation on CH0, no RU/RD
16-level modulation on CH1, no RU/RD
Table 13. Profile Pin and Channel Assignments for Two-Level Modulation (RU/RD Enabled)
Profile Pin Config. (PPC)
(FR1[14:12])
P0
P1
P2
P3
Description
101
CH0
CH1
CH0 RU/RD
CH1 RU/RD
Two-level modulation on CH0 and CH1 with RU/RD
Table 14. Profile Pin and Channel Assignments for Eight-Level Modulation (RU/RD Enabled)
Profile Pin Config. (PPC)
(FR1[14:12])
P0
P1
P2
P3
Description
X10
X11
CH0
CH1
CH0
CH1
CH0
CH1
CH0 RU/RD
CH1 RU/RD
Eight-level modulation on CH0 with RU/RD
Eight-level modulation on CH1 with RU/RD
Rev. A | Page 23 of 44
AD9958
For the configuration shown in Table 17, the profile (channel
word) register is chosen based on the 2-bit value presented to
Profile Pins [P1:P2] or [P3:P4].
MODULATION USING SDIO_x PINS FOR RU/RD
For RU/RD bits = 11, the SDIO_1, SDIO_2, and SDIO_3 pins
are available for RU/RD. In this mode, modulation levels of 2, 4,
and 16 are available. Note that the serial I/O port can be used only
in 1-bit serial mode.
For example, if PPC = 101, [P0:P1] = 11, and [P2:P3] = 01, the
contents of the Channel Word 3 register of Channel 0 are
presented to the output of Channel 0 and the contents of the
Channel Word 1 register of Channel 1 are presented to the
output of Channel 1. SDIO_1 and SDIO_2 provide the RU/RD
function.
Two-Level Modulation Using SDIO Pins for RU/RD
Table 15. Profile Pin and Channel Assignments in Two-Level
Modulation (RU/RD Enabled)
Profile Pin Config. (PPC)
(FR1[14:12])
16-Level Modulation Using SDIO Pins for RU/RD
P0
P1
P2
P3
The RU/RD bits = 11 (SDIO_1 available for RU/RD), and the
level is set to 16. See the pin assignments shown in Table 18.
XXX
N/A
N/A
CH0
CH1
For the configuration in Table 15, each profile pin is dedicated
to a specific channel. In this case, the SDIO_x pins can be used
for the RU/RD function, as described in Table 16.
For the configuration shown in Table 18, the profile (channel
word) register is chosen based on the 4-bit value presented to
Profile Pins [P0:P3]. For example, if PPC = X10 and [P0:P3] =
1101, then the contents of the Channel Word 13 register of
Channel 0 is presented to the output of Channel 0. The SDIO_1
pin provides the RU/RD function.
Four-Level Modulation Using SDIO Pins for RU/RD
For RU/RD bits = 11 (the SDIO_1 and SDIO_2 pins are avail-
able for RU/RD), the modulation level is set to 4. See Table 17
for pin assignments, including SDIO_x pin assignments.
Table 16. Channel and SDIO_1/SDIO_2/SDIO_3 Pin Assignments for RU/RD Operation
SDIO_1
SDIO_2
SDIO_3
Description
1
1
1
1
0
0
1
1
0
1
0
1
Triggers the ramp-up function for CH0
Triggers the ramp-down function for CH0
Triggers the ramp-up function for CH1
Triggers the ramp-down function for CH1
Table 17. Channel and Profile Pin Assignments, Including SDIO_1/SDIO_2/SDIO_3 Pin Assignments for RU/RD Operation
Profile Pin Configuration (PPC) (FR1[14:12])
P0
P1
P2
P3
SDIO_1
SDIO_2
SDIO_3
101
CH0
CH0
CH1
CH1
CH0 RU/RD
CH1 RU/RD
N/A
Table 18. Channel and Profile Pin Assignments, Including SDIO_1 Pin Assignments for RU/RD Operation
Profile Pin Configuration (PPC) (FR1[14:12])
P0
P1
P2
P3
SDIO_1
SDIO_2
SDIO_3
N/A
N/A
X10
X11
CH0
CH1
CH0
CH1
CH0
CH1
CH0
CH1
CH0 RU/RD
CH1 RU/RD
N/A
N/A
Rev. A | Page 24 of 44
AD9958
LINEAR SWEEP MODE
Setting the Slope of the Linear Sweep
Linear sweep mode enables the user to sweep frequency, phase,
or amplitude from a starting point (S0) to an endpoint (E0).
The purpose of linear sweep mode is to provide better band-
width containment compared to direct modulation by replacing
greater instantaneous changes with more gradual, user-defined
changes between S0 and E0.
The slope of the linear sweep is set by the intermediate step size
(delta-tuning word) between S0 and E0 and the time spent
(sweep ramp rate word) at each step. The resolution of the
delta-tuning word is 32 bits for frequency, 14 bits for phase, and
10 bits for amplitude. The resolution for the delta ramp rate
word is eight bits.
In linear sweep mode, S0 is loaded into the Channel Word 0
register (S0 is represented by one of three registers: Register 0x04,
Register 0x05, or Register 0x06, depending on the type of sweep)
and E0 is always loaded into Channel Word 1 (Register 0x0A).
If E0 is configured for frequency sweep, the resolution is 32 bits,
phase sweep is 14 bits, and amplitude sweep is 10 bits. When
sweeping phase or amplitude, the word value must be MSB aligned
in the Channel Word 1 register. The unused bits are don’t care
bits. The profile pins are used to trigger and control the direction
of the linear sweep for frequency, phase, and amplitude. All
channels can be programmed separately for a linear sweep. In
linear sweep mode, Profile Pin P0 is dedicated to Channel 0.
Profile Pin P1 is dedicated to Channel 1, and so on.
In linear sweep, each channel is assigned a rising delta word
(RDW, Register 0x08) and a rising sweep ramp rate word
(RSRR, Register 0x07). These settings apply when sweeping up
toward E0. The falling delta word (FDW, Register 0x09) and
falling sweep ramp rate (FSRR, Register 0x07) apply when
sweeping down toward S0. Figure 36 displays a linear sweep up
and then down using a profile pin. Note that the linear sweep
no-dwell bit is disabled; otherwise, the sweep accumulator
returns to 0 upon reaching E0.
E0
RDW
Δf,p,a
FDW
Δf,p,a
The AD9958 has the ability to ramp up or ramp down (RU/RD)
the output amplitude (using the 10-bit output scalar) before and
after a linear sweep. If the RU/RD feature is desired, unused
profile pins or unused SDIO_1/SDIO_2/SDIO_3 pins can be
configured for the RU/RD operation.
RSRR
FSRR
Δt
Δt
S0
PROFILE PIN
To enable linear sweep mode for a particular channel, the AFP
select bits (CFR[23:22]), the modulation level bits (FR1[9:8]),
and the linear sweep enable bit (CFR[14]) are programmed.
TIME
Figure 36. Linear Sweep Parameters
The AFP select bits determine the type of linear sweep to be
performed. The modulation level bits must be set to 00 (two-
level) for that specific channel (see Table 19 and Table 20)
For a piecemeal or a nonlinear transition between S0 and E0,
the delta-tuning words and ramp rate words can be repro-
grammed during the transition to produce the desired response.
Table 19. Linear Sweep Parameter to Sweep
The formulas for calculating the step size of RDW or FDW for
delta frequency, delta phase, or delta amplitude are as follows:
AFP Select
(CFR[23:22])
Linear Sweep Enable
(CFR[14])
Description
N/A
Amplitude sweep
Frequency sweep
Phase sweep
RDW
⎛
⎜
⎝
⎞
⎟
⎠
00
01
10
11
1
1
1
1
Δf =
× SYSCLK (Hz)
232
RDW
⎛
⎜
⎝
⎞
⎠
ΔΦ =
Δa =
×360°
⎟
214
RDW
Table 20. Modulation Level Assignments
⎛
⎞
⎠
×1024 (DAC full-scale current)
⎟
⎜
210
Modulation Level (FR1[9:8])
Description
⎝
00 (Required in Linear Sweep)
Two-level modulation
Four-level modulation
Eight-level modulation
16-level modulation
The formula for calculating delta time from RSRR or FSRR is
t = RSRR ×1/SYNC _CLK
01
10
11
(
)
At 500 MSPS operation (SYNC_CLK = 125 MHz), the maxi-
mum time interval between steps is 1/125 MHz × 256 = 2.048 μs.
The minimum time interval is (1/125 MHz) × 1 = 8.0 ns.
The sweep ramp rate block (timer) consists of a loadable 8-bit
down counter that continuously counts down from the loaded
value to 1. When the ramp rate timer equals 1, the proper ramp rate
value is loaded and the counter begins counting down to 1 again.
Rev. A | Page 25 of 44
AD9958
This load and countdown operation continues for as long as the
timer is enabled. However, the count can be reloaded before
reaching 1 by either of the following two methods:
When the profile pin transitions from high to low, the FDW is
applied to the input of the sweep accumulator and the FSRR bits
are loaded into the sweep rate timer.
The FDW accumulates at the rate given by the falling sweep ramp
rate (FSRR) until the output is equal to the CFTW0 register
(Register 0x04) value. The sweep is then complete, and the output
is held constant in frequency.
•
Method 1 is to change the profile pin. When the profile pin
changes from Logic 0 to Logic 1, the rising sweep ramp rate
(RSRR) register value is loaded into the ramp rate timer,
which then proceeds to count down as normal. When the
profile pin changes from Logic 1 to Logic 0, the falling sweep
ramp rate (FSRR) register value is loaded into the ramp
rate timer, which then proceeds to count down as normal.
Method 2 is to set the CFR[14] bit and issue an I/O update.
If sweep is enabled and CFR[14] is set, the ramp rate timer
loads the value determined by the profile pin. If the profile
pin is high, the ramp rate timer loads the RSRR; if the profile
pin is low, the ramp rate timer loads FSRR.
See Figure 37 for the linear sweep block diagram. Figure 39
depicts a frequency sweep with no-dwell mode disabled. In this
mode, the output follows the state of the profile pin. A phase or
amplitude sweep works in the same manner.
•
LINEAR SWEEP NO-DWELL MODE
If the linear sweep no-dwell bit is set (CFR[15]), the rising sweep is
started in an identical manner to the dwell linear sweep mode;
that is, upon detecting Logic 1 on the profile input pin, the rising
sweep action is initiated. The word continues to sweep up at the
rate set by the rising sweep ramp rate at the resolution set by the
rising delta word until it reaches the terminal value. Upon reaching
the terminal value, the output immediately reverts to the starting
point and remains until Logic 1 is detected on the profile pin.
Frequency Linear Sweep Example: AFP Bits = 10
In the following example, the modulation level bits (FR1[9:8]) = 00,
the linear sweep enable bit (CFR[14]) = 1, and the linear sweep
no-dwell bit (CFR[15]) = 0.
In linear sweep mode, when the profile pin transitions from low
to high, the RDW is applied to the input of the sweep accumulator
and the RSRR register is loaded into the sweep rate timer.
Figure 38 shows an example of the no-dwell mode. The points
labeled A indicate where a rising edge is detected on the profile
pin, and the points labeled B indicate where the AD9958 has
determined that the output has reached E0 and reverts to S0.
The falling sweep ramp rate bits (LSRR[15:8]) and the falling
delta word bits (FDW[31:0]) are unused in this mode.
The RDW accumulates at the rate given by the rising sweep
ramp rate (RSRR) bits until the output is equal to the CW1
register value. The sweep is then complete, and the output is
held constant in frequency.
SWEEP ACCUMULATOR
SWEEP ADDER
0
0
32
32
32
32
–1
0
Z
MUX
1
FDW
RDW
0
32
0
MUX
1
MUX
1
MUX
1
0
32
PROFILE PIN
CFTW0
RAMP RATE TIMER:
8-BIT LOADABLE DOWN COUNTER
ACCUMULATOR RESET
LOGIC
LIMIT LOGICTO
KEEP SWEEP BETWEEN
S0 AND E0
8
32
PROFILE PIN
CW1
MUX
1
0
RATE TIME
LOAD CONTROL
LOGIC
FSRR RSRR
Figure 37. Linear Sweep Block Diagram
Rev. A | Page 26 of 44
AD9958
fOUT
B
B
B
FTW1
A
A
A
FTW0
TIME
SINGLE-TONE
MODE
P2 = 0
P2 = 1
P2 = 0
P2 = 1
P2 = 0
P2 = 1
LINEAR SWEEP MODE ENABLE—NO-DWELL BIT SET
Figure 38. Linear Sweep Mode (No-Dwell Enabled)
fOUT
B
FTW1
A
FTW0
TIME
SINGLE-TONE
MODE
LINEAR SWEEP MODE
P2 = 0
P2 = 1
P2 = 0
AT POINT A: LOAD RISING RAMP RATE REGISTER, APPLY RDW<31:0>
AT POINT B: LOAD FALLING RAMP RATE REGISTER, APPLY FDW<31:0>
Figure 39. Linear Sweep Mode (No-Dwell Disabled)
Continuous Clear Bits
SWEEP AND PHASE ACCUMULATOR CLEARING
FUNCTIONS
The continuous clear bits are static control signals that, when
active high, hold the respective accumulator at 0 while the bit is
active. When the bit goes low, the respective accumulator is
allowed to operate.
The AD9958 allows two different clearing functions. The first
is a continuous zeroing of the sweep logic and phase accumula-
tor (clear and hold). The second is a clear and release or automatic
zeroing function. CFR[4] is the autoclear sweep accumulator bit
and CFR[2] is the autoclear phase accumulator bit. The continuous
clear bits are located in CFR, where CFR[3] clears the sweep
accumulator and CFR[1] clears the phase accumulator.
Clear and Release Bits
The autoclear sweep accumulator bit, when set, clears and
releases the sweep accumulator upon an I/O update or a change
in the profile input pins. The autoclear phase accumulator bit,
when set, clears and releases the phase accumulator upon an
I/O update or a change in the profile pins. The automatic
clearing function is repeated for every subsequent I/O update or
change in profile pins until the clear and release bits are reset
via the serial port.
Rev. A | Page 27 of 44
AD9958
OUTPUT AMPLITUDE CONTROL MODE
A special feature of this mode is that the maximum output
amplitude allowed is limited by the contents of the amplitude
scale factor (ACR[9:0]). This allows the user to ramp to a value
less than full scale.
The 10-bit scale factor (multiplier) controls the ramp-up and
ramp-down (RU/RD) time of an on/off emission from the DAC.
In burst transmissions of digital data, it reduces the adverse
spectral impact of abrupt bursts of data. The multiplier can
be bypassed by clearing the amplitude multiplier enable bit
(ACR[12] = 0).
Ramp Rate Timer
The ramp rate timer is a loadable down counter that generates
the clock signal to the 10-bit counter that generates the internal
scale factor. The ramp rate timer is loaded with the value of the
LSRR (Register 0x07) each time the counter reaches 1 (decimal).
This load and countdown operation continues for as long as the
timer is enabled unless the timer is forced to load before
reaching a count of 1.
Automatic and manual RU/RD modes are supported. The auto-
matic mode generates a zero-scale up to a full-scale (10 bits)
linear ramp at a rate determined by ACR (Register 0x06). The
start and direction of the ramp can be controlled by either the
profile pins or the SDIO_1/SDIO_2/SDIO_3 pins.
Manual mode allows the user to directly control the output
amplitude by manually writing to the amplitude scale factor
value in the ACR (Register 0x06). Manual mode is enabled by
setting ACR[12] = 1 and ACR[11] = 0.
If the load ARR at I/O_UPDATE bit (ACR[10]) is set, the ramp
rate timer is loaded at an I/O update, a change in profile input,
or upon reaching a value of 1. The ramp timer can be loaded
before reaching a count of 1 by three methods.
Automatic RU/RD Mode Operation
•
In the first method, the profile pins or the SDIO_1/
SDIO_2/SDIO_3 pins are changed. When the control
signal changes state, the ACR value is loaded into the ramp
rate timer, which then proceeds to count down as normal.
In the second method, the load ARR at I/O_UPDATE bit
(ACR[10]) is set, and an I/O update is issued.
Automatic RU/RD mode is active when both ACR[12] and
ACR[11] are set. When automatic RU/RD is enabled, the scale
factor is internally generated and applied to the multiplier input
port for scaling the output. The scale factor is the output of a 10-bit
counter that increments/decrements at a rate set by the 8-bit
output ramp rate register. The scale factor increments if the
external pin is high and decrements if the pin is low. The inter-
nally generated scale factor step size is controlled by ACR[15:14].
Table 21 describes the increment/decrement step size of the
internally generated scale factor per ACR[15:14].
•
•
The third method is to change from inactive automatic
RU/RD mode to active automatic RU/RD mode.
RU/RD Pin-to-Channel Assignment
When all four channels are in single-tone mode, the profile pins
are used for RU/RD operation.
Table 21. Increment/Decrement Step Size Assignments
When linear sweep and RU/RD are activated, the SDIO_1/
SDIO_2/SDIO_3 pins are used for RU/RD operation.
Increment/Decrement Step Size
(ACR [15:14])
Size
In modulation mode, refer to the Modulation Mode section for
pin assignments.
00
01
10
11
1
2
4
8
Table 22. Profile Pin Assignments for RU/RD Operation
Profile Pin
RU/RD Operation
P2
P3
CH0
CH1
Table 23. Channel Assignments of SDIO_1/SDIO_2/SDIO_3 Pins for RU/RD Operation
Linear Sweep and RU/RD Modes Enabled
Simultaneously
Enable for CH0
Enable for CH0
Enable for CH1
Enable for CH1
SDIO_1 SDIO_2 SDIO_3 Ramp-Up/Ramp-Down Control Signal Assignment
1
1
1
1
0
0
1
1
0
1
0
1
Ramp-up function for CH0
Ramp-down function for CH0
Ramp-up function for CH1
Ramp-down function for CH1
Rev. A | Page 28 of 44
AD9958
SYNCHRONIZING MULTIPLE AD9958 DEVICES
The AD9958 allows easy synchronization of multiple AD9958
devices. At power-up, the phase of SYNC_CLK can be offset
between multiple devices. To correct for the offset and align the
SYNC_CLK edges, there are three methods (one automatic mode
and two manual modes) of synchronizing the SYNC_CLK edges.
These modes force the internal state machines of multiple
devices to a known state, which aligns the SYNC_CLK edges.
Table 24. System Clock Offset (Delay) Assignments
System Clock
Offset (FR2[1:0])
SYNC_OUT/SYNC_IN
Propagation Delay
00
01
10
11
0 ≤ delay ≤ 1
1 ≤ delay ≤ 2
2 ≤ delay ≤ 3
3 ≤ delay ≤ 4
In addition, the user must send a coincident I/O_UPDATE to
multiple devices to maintain synchronization. Any mismatch in
REF_CLK phase between devices results in a corresponding
phase mismatch on the SYNC_CLK edges.
Automatic Synchronization Status Bits
If a slave device falls out of sync, the sync status bit is set high.
The multidevice sync status bit (FR2[5]) can be read through
the serial port. It is automatically cleared when read.
AUTOMATIC MODE SYNCHRONIZATION
The synchronization routine continues to operate regardless of
the state of FR2[5]. FR2[5] can be masked by writing Logic 1 to
the multidevice sync mask bit (FR2[4]). If FR2[5] is masked, it is
held low.
In automatic mode, multiple part synchronization is achieved
by connecting the SYNC_OUT pin on the master device to the
SYNC_IN pins of the slave devices. Devices are configured as
master or slave through programming bits, accessible via the
serial port.
MANUAL SOFTWARE MODE SYNCHRONIZATION
Manual software mode is enabled by setting the manual software
sync bit (FR1[0]) to Logic 1 in a device. In this mode, the I/O
update that writes the manual software sync bit to Logic 0 stalls
the state machine of the clock generator for one system clock
cycle. Stalling the clock generation state machine by one cycle
changes the phase relationship of SYNC_CLK between devices
by one system clock period (90°).
A configuration for synchronizing multiple AD9958 devices in
automatic mode is shown in the Application Circuits section. In
this configuration, the AD9510 provides coincident REF_CLK
and SYNC_OUT signals to all devices.
Operation
The first step is to program the master and slave devices for
their respective roles and then write the auto sync enable bit
(FR2[7] = 1. Enabling the master device is performed by writing
its multidevice sync master enable bit in Function Register 2
(FR2[6]) = 1. This causes the SYNC_OUT of the master device
to output a pulse that has a pulse width equal to one system
clock period and a frequency equal to one-fourth of the system
clock frequency. Enabling devices as slaves is performed by
writing FR2[6] = 0.
Note that the user may have to repeat this process until the
devices have their SYNC_CLK signals in phase. The SYNC_IN
input can be left floating because it has an internal pull-up. The
SYNC_OUT pin is not used.
The synchronization is complete when the master and slave
devices have their SYNC_CLK signals in phase.
MANUAL HARDWARE MODE SYNCHRONIZATION
Manual hardware mode is enabled by setting the manual hardware
sync bit (FR1[1]) to Logic 1 in a device. In manual hardware
synchronization mode, the SYNC_CLK stalls by one system
clock cycle each time a rising edge is detected on the SYNC_IN
input. Stalling the SYNC_CLK state machine by one cycle changes
the phase relationship of SYNC_CLK between devices by one
system clock period (90°).
In automatic synchronizing mode, the slave devices sample
SYNC_OUT pulses from the master device on the SYNC_IN
of the slave devices, and a comparison of all state machines is
made by the autosynchronization circuitry. If the slave devices
state machines are not identical to the master, the slave devices
state machines are stalled for one system clock cycle. This proce-
dure synchronizes the slave devices within three SYNC_CLK
periods.
Note that the user may have to repeat the process until the devices
have their SYNC_CLK signals in phase. The SYNC_IN input
can be left floating because it has an internal pull-up. The
SYNC_OUT is not used.
Delay Time Between SYNC_OUT and SYNC_IN
When the delay between SYNC_OUT and SYNC_IN exceeds
one system clock period, the system clock offset bits (FR2[1:0])
are used to compensate. The default state of these bits is 00, which
implies that the SYNC_OUT of the master and the SYNC_IN of
the slave have a propagation delay of less than one system clock
period. If the propagation time is greater than one system clock
period, the time should be measured and the appropriate offset
programmed. Table 24 describes the delays required per system
clock offset value.
The synchronization is complete when the master and slave
devices have their SYNC_CLK signals in phase.
Rev. A | Page 29 of 44
AD9958
If the setup time between these signals is met, then constant
latency (pipeline) to the DAC output exists. For example, if
repetitive changes to phase offset via the SPI port is desired, the
latency of those changes to the DAC output is constant; otherwise,
a time uncertainty of one SYNC_CLK period is present.
I/O_UPDATE, SYNC_CLK, AND SYSTEM CLOCK
RELATIONSHIPS
I/O_UPDATE and SYNC_CLK are used together to transfer
data from the serial I/O buffer to the active registers in the
device. Data in the buffer is inactive.
The I/O_UPDATE is essentially oversampled by the SYNC_CLK.
Therefore, I/O_UPDATE must have a minimum pulse width
greater than one SYNC_CLK period.
SYNC_CLK is a rising edge active signal. It is derived from
the system clock and a divide-by-4 frequency divider. The
SYNC_CLK, which is externally provided, can be used to
synchronize external hardware to the AD9958 internal clocks.
The timing diagram shown in Figure 40 depicts when data in
the buffer is transferred to the active registers.
I/O_UPDATE initiates the start of a buffer transfer. It can be
sent synchronously or asynchronously relative to the SYNC_CLK.
SYSCLK
A
B
SYNC_CLK
I/O_UPDATE
DATA IN
REGISTERS
N
N + 1
N – 1
DATA IN
I/O BUFFERS
N
N + 1
N + 2
THE DEVICE REGISTERS AN I/O UPDATE AT POINT A. THE DATA IS TRANSFERRED FROM THE ASYNCHRONOUSLY LOADED I/O BUFFERS AT POINT B.
Figure 40. I/O_UPDATE Transferring Data from I/O Buffer to Active Registers
Rev. A | Page 30 of 44
AD9958
SERIAL I/O PORT
Phase 2 of the I/O cycle consists of the actual data transfer
OVERVIEW
(write/read) between the serial port controller and the serial
port buffer. The number of bytes transferred during this phase
of the communication cycle is a function of the register being
accessed. The actual number of additional SCLK rising edges
required for the data transfer and instruction byte depends on
the number of bytes in the register and the serial I/O mode of
operation.
The AD9958 serial I/O port offers multiple configurations to
provide significant flexibility. The serial I/O port offers an SPI-
compatible mode of operation that is virtually identical to the
SPI operation found in earlier Analog Devices DDS products.
The flexibility is provided by four data pins (SDIO_0, SDIO_1,
SDIO_2, SDIO_3) that allow four programmable modes of
serial I/O operation.
For example, when accessing Function Register 1 (FR1), which
is three bytes wide, Phase 2 of the I/O cycle requires that three
bytes be transferred. After transferring all data bytes per the
instruction byte, the communication cycle is completed for that
register.
Three of the four data pins (SDIO_1, SDIO_2, SDIO_3) can be
used for functions other than serial I/O port operation. These pins
can also be used to initiate a ramp-up or ramp-down (RU/RD)
of the 10-bit amplitude output scalar. In addition, SDIO_3 can
be used to provide the SYNC_I/O function that resynchronizes
the serial I/O port controller if it is out of proper sequence.
At the completion of a communication cycle, the AD9958 serial
port controller expects the next set of rising SCLK edges to be
the instruction byte for the next communication cycle. All data
written to the AD9958 is registered on the rising edge of SCLK.
Data is read on the falling edge of SCLK (see Figure 43 through
Figure 49). The timing specifications for Figure 41 and Figure 42
are described in Table 25.
The maximum speed of the serial I/O port SCLK is 200 MHz,
but the four data pins (SDIO_0, SDIO_1, SDIO_2, SDIO_3)
can be used to further increase data throughput. The maximum
data throughput using all the SDIO pins (SDIO_0, SDIO_1,
SDIO_2, SDIO_3) is 800 Mbps.
Note that both channels share Register 0x03 to Register 0x18,
which are shown in the Register Maps and Bit Descriptions
section. This address sharing enables both DDS channels to be
written to simultaneously. For example, if a common frequency
tuning word is desired for both channels, it can be written once
through the serial I/O port to both channels. This is the default
mode of operation (all channels enabled). To enable each channel
to be independent, the two channel enable bits found in the
channel select register (CSR, Register 0x00) must be used.
tPRE
tSCLK
CS
tDSU
tSCLKPWL
SCLK
tSCLKPWH
tDHLD
SDIO_x
Figure 41. Setup and Hold Timing for the Serial I/O Port
There are effectively four sets or copies of addresses (Register 0x03
to Register 0x18) that the channel enable bits can access to provide
channel independence. See the Descriptions for Control Registers
section for further details of programming channels that are
common to or independent from each other. To properly read
back Register 0x03 to Register 0x18, the user must enable only
one channel enable bit at a time.
CS
SCLK
SDIO_x
SDO (SDIO_2)
Serial operation of the AD9958 occurs at the register level,
not the byte level; that is, the controller expects that all bytes
contained in the register address are accessed. The SYNC_I/O
function can be used to abort an I/O operation, thereby allowing
fewer than all bytes to be accessed. This feature can be used to
program only a part of the addressed register. Note that only
completed bytes are affected.
tDV
Figure 42. Timing Diagram for Data Read for Serial I/O Port
Table 25. Timing Specifications
Parameter Min Unit
Description
tPRE
1.0
5.0
2.2
2.2
1.6
0
ns min CS setup time
tSCLK
tDSU
tSCLKPWH
tSCLKPWL
tDHLD
tDV
ns min Period of serial data clock
ns min Serial data setup time
ns min Serial data clock pulse width high
ns min Serial data clock pulse width low
ns min Serial data hold time
ns min Data valid time
There are two phases to a serial communications cycle. Phase 1
is the instruction cycle, which writes the instruction byte into
the AD9958. Each bit of the instruction byte is registered on
each corresponding rising edge of SCLK. The instruction byte
defines whether the upcoming data transfer is a write or read
operation. The instruction byte contains the serial address of
the address register.
12
Rev. A | Page 31 of 44
AD9958
Each set of communication cycles does not require an I/O update
to be issued. The I/O update transfers data from the I/O port
buffer to active registers. The I/O update can be sent for each
communication cycle or can be sent when all serial operations
are complete. However, data is not active until an I/O update is
sent, with the exception of the channel enable bits in the channel
select register (CSR). These bits do not require an I/O update to
be enabled.
this pin. The SDO function is not available in 2-bit or 4-bit serial
I/O modes.
SYNC_I/O
The SYNC_I/O function is available in 1-bit and 2-bit modes.
SDIO_3 serves as the SYNC_I/O pin when this function is
active. Bits CSR[2:1] control the configuration of this pin.
Otherwise, the SYNC_I/O function is used to synchronize the
I/O port state machines without affecting the addressable register
contents. An active high input on the SYNC_I/O (SDIO_3) pin
causes the current communication cycle to abort. After SDIO_3
returns low (Logic 0), another communication cycle can begin,
starting with the instruction byte write. The SYNC_I/O function is
not available in 4-bit serial I/O mode.
INSTRUCTION BYTE DESCRIPTION
The instruction byte contains the following information:
MSB
D7
LSB
D0
A0
D6
x1
D5
x1
D4
D3
D2
D1
R/W
A4
A3
A2
A1
MSB/LSB TRANSFER DESCRIPTION
1 x = don’t care bit.
The AD9958 serial port can support both most significant bit
(MSB) first or least significant bit (LSB) first data formats. This
functionality is controlled by CSR[0]. MSB first is the default
mode. When CSR[0] is set high, the AD9958 serial port is in
LSB first format. The instruction byte must be written in the
format indicated by CSR[0], that is, if the AD9958 is in LSB first
mode, the instruction byte must be written from LSB to MSB. If
the AD9958 is in MSB first mode (default), the instruction byte
must be written from MSB to LSB.
W
Bit D7 of the instruction byte (R/ ) determines whether a read
or write data transfer occurs after the instruction byte write. A
logic high indicates a read operation. A logic low indicates a
write operation.
Bit D4 to Bit D0 of the instruction byte determine which register is
accessed during the data transfer portion of the communication
cycle. The internal byte addresses are generated by the AD9958.
SERIAL I/O PORT PIN DESCRIPTION
Example Operation
Serial Data Clock (SCLK)
To write Function Register 1 (FR1, Register 0x01) in MSB first
format, apply an instruction byte of 00000001 starting with the
MSB (in the following example instruction byte, the MSB is
D7). From this instruction, the internal controller recognizes a
write transfer of three bytes starting with the MSB, FR1[23].
Bytes are written on each consecutive rising SCLK edge until
Bit 0 is transferred. When the last data bit is written, the I/O
communication cycle is complete and the next byte is considered
an instruction byte.
The serial data clock pin is used to synchronize data to and
from the internal state machines of the AD9958. The maximum
SCLK toggle frequency is 200 MHz.
CS
Chip Select (
)
The chip select pin allows more than one AD9958 device to be
on the same set of serial communications lines. The chip select
is an active low enable pin. SDIO_x inputs go to a high imped-
CS
CS
ance state when
communication cycle, that cycle is suspended until
CS
is high. If
is driven high during any
Example Instruction Byte1
CS
is
MSB
D7
0
LSB
D0
1
reactivated low. The
pin can be tied low in systems that
maintain control of SCLK.
D5
D6
D4
D3
D2
D1
0
0
0
0
0
0
Serial Data I/O (SDIO_x)
1 Note that the bit values are for example purposes only.
Of the four SDIO pins, only the SDIO_0 pin is a dedicated SDIO
pin. SDIO_1, SDIO_2, and SDIO_3 can also be used to ramp
up/ramp down the output amplitude. Bits[2:1] in the channel
select register (CSR, Register 0x00) control the configuration
of these pins. See the Serial I/O Modes of Operation for more
information.
To write Function Register 1 (FR1) in LSB first format, apply an
instruction byte of 00000001, starting with the LSB bit (in the
preceding example instruction byte, the LSB is D0). From this
instruction, the internal controller recognizes a write transfer of
three bytes, starting with the LSB, FR1[0]. Bytes are written on
each consecutive rising SCLK edge until Bit 23 is transferred.
When the last data bit is written, the I/O communication cycle is
complete and the next byte is considered an instruction byte.
SERIAL I/O PORT FUNCTION DESCRIPTION
Serial Data Out (SDO)
The SDO function is available in single-bit (3-wire) mode only.
In SDO mode, data is read from the SDIO_2 pin for protocols
that use separate lines for transmitting and receiving data (see
Table 26 for pin configuration options). Bits[2:1] in the channel
select register (CSR, Register 0x00) control the configuration of
Rev. A | Page 32 of 44
AD9958
In single-bit serial mode, 2-wire interface operation, the
SERIAL I/O MODES OF OPERATION
SDIO_0 pin is the single serial data I/O pin. In single-bit serial
mode 3-wire interface operation, the SDIO_0 pin is the serial
data input pin and the SDIO_2 pin is the output data pin.
Regardless of the number of wires used in the interface, the
SDIO_3 pin is configured as an input and operates as the
SYNC_I/O pin in the single-bit serial mode and 2-bit serial
mode. The SDIO_1 pin is unused in this mode (see Table 26).
The following are the four programmable modes of serial I/O
port operation:
•
•
•
•
Single-bit serial 2-wire mode (default mode)
Single-bit serial 3-wire mode
2-bit serial mode
4-bit serial mode (SYNC_I/O not available)
2-Bit Serial Mode
Table 26 displays the function of all six serial I/O interface pins,
depending on the mode of serial I/O operation programmed.
The SPI port operation in 2-bit serial mode is identical to the
SPI port operation in single-bit serial mode, except that two bits
of data are registered on each rising edge of SCLK. Therefore, it
only takes four clock cycles to transfer eight bits of information.
The SDIO_0 pin contains the even numbered data bits using
the notation D[7:0], and the SDIO_1 pin contains the odd
numbered data bits. This even and odd numbered pin/data
alignment is valid in both MSB and LSB first formats (see
Figure 44).
Table 26. Serial I/O Port Pin Function vs. Serial I/O Mode
Single-Bit
Serial 2-Wire
Mode
Single-Bit
Serial 3-Wire
Mode
2-Bit
Serial
Mode
4-Bit
Serial
Mode
Pin
SCLK
Serial clock
Serial clock
Serial clock Serial
clock
CS
Chip select
Chip select
Chip select
Chip
select
SDIO_0 Serial data I/O Serial data in
Serial data
I/O
Serial
data I/O
4-Bit Serial Mode
SDIO_1 Not used for
SDIO1
SDIO_2 Not used for
SDIO1
Not used for
SDIO1
Serial data
out (SDO)
Serial data
I/O
Not used
for SDIO1
Serial
data I/O
Serial
data I/O
Serial
data I/O
The SPI port in 4-bit serial mode is identical to the SPI port in
single-bit serial mode, except that four bits of data are registered
on each rising edge of SCLK. Therefore, it takes only two clock
cycles to transfer eight bits of information. The SDIO_0 and
SDIO_2 pins contain even numbered data bits using the notation
D[7:0], and the SDIO_0 pin contains the LSB of the nibble. The
SDIO_1 and SDIO_3 pins contain the odd numbered data bits,
and the SDIO_1 pin contains the LSB of the nibble to be accessed.
SDIO_3 SYNC_I/O
SYNC_I/O
SYNC_I/O
1 In serial mode, these pins (SDIO_0/SDIO_1/SDIO_2/SDIO_3) can be used for
RU/RD operation.
The two bits in the channel select register, CSR[2:1], set the
serial I/O mode of operation and are defined in Table 27.
Note that when programming the device for 4-bit serial mode,
it is important to keep the SDIO_3 pin at Logic 0 until the device is
programmed out of the single-bit serial mode. Failure to do so
can result in the serial I/O port controller being out of
sequence.
Table 27. Serial I/O Mode of Operation
Serial I/O Mode Select
(CSR[2:1])
Mode of Operation
00
01
10
11
Single-bit serial mode (2-wire mode)
Single-bit serial mode (3-wire mode)
2-bit serial mode
Figure 43 through Figure 45 represent write timing diagrams
for each of the serial I/O modes available. Both MSB and LSB
first modes are shown. LSB first bits are shown in parentheses.
The clock stall low/high feature shown is not required. It is used
to show that data (SDIO) must have the proper setup time
relative to the rising edge of SCLK.
4-bit serial mode
Single-Bit Serial (2-Wire and 3-Wire) Modes
The single-bit serial mode interface allows read/write access to
all registers that configure the AD9958. MSB first or LSB first
transfer formats are supported. In addition, the single-bit serial
mode interface port can be configured either as a single pin I/O,
which allows a 2-wire interface, or as two unidirectional pins
for input/output, which enable a 3-wire interface. Single-bit
mode allows the use of the SYNC_I/O function.
Figure 46 through Figure 49 represent read timing diagrams for
each of the serial I/O modes available. Both MSB and LSB first
modes are shown. LSB first bits are shown in parentheses. The
clock stall low/high feature shown is not required. It is used to
show that data (SDIO) must have the proper setup time relative
to the rising edge of SCLK for the instruction byte and the read
data that follows the falling edge of SCLK.
Rev. A | Page 33 of 44
AD9958
INSTRUCTION CYCLE
DATA TRANSFER CYCLE
CS
SCLK
I7
(I0)
I6
(I1)
I5
(I2)
I4
(I3)
I3
(I4)
I2
(I5)
I1
(I6)
I0
(I7)
D7
(D0)
D6
(D1)
D5
(D2)
D4
(D3)
D3
(D4)
D2
(D5)
D1
(D6)
D0
(D7)
SDIO_0
Figure 43. Single-Bit Serial Mode Write Timing—Clock Stall Low
INSTRUCTION CYCLE
DATA TRANSFER CYCLE
CS
SCLK
I7
I5
I3
I1
D7
D5
D3
D1
SDIO_1
SDIO_0
(I1)
(I3)
(I5)
(I7)
(D1)
(D3)
(D5)
(D7)
I6
(I0)
I4
(I2)
I2
(I4)
I0
(I6)
D6
(D0)
D4
(D2)
D2
(D4)
D0
(D6)
Figure 44. 2-Bit Serial Mode Write Timing—Clock Stall Low
INSTRUCTION CYCLE
DATA TRANSFER CYCLE
CS
SCLK
I7
(I3)
I3
(I7)
D7
(D3)
D3
(D7)
SDIO_3
I6
I2
D6
D2
SDIO_2
SDIO_1
(I2)
(I6)
(D2)
(D6)
I5
(I1)
I1
(I5)
D5
(D1)
D1
(D5)
I4
(I0)
I0
(I4)
D4
(D0)
D0
(D4)
SDIO_0
Figure 45. 4-Bit Serial Mode Write Timing—Clock Stall Low
Rev. A | Page 34 of 44
AD9958
DATA TRANSFER CYCLE
INSTRUCTION CYCLE
CS
SCLK
I7
(I0)
I6
(I1)
I5
(I2)
I4
(I3)
I3
(I4)
I2
(I5)
I1
(I6)
I0
(I7)
D7
(D0)
D6
(D1)
D5
(D2)
D4
(D3)
D3
(D4)
D2
(D5)
D1
(D6)
D0
(D7)
SDIO_0
Figure 46. Single-Bit Serial Mode (2-Wire) Read Timing—Clock Stall High
DATA TRANSFER CYCLE
INSTRUCTION CYCLE
CS
SCLK
I7
(I0)
I6
(I1)
I5
(I2)
I4
(I3)
I3
(I4)
I2
(I5)
I1
(I6)
I0
(I7)
DON'T CARE
SDIO_0
SDO
D7
(D0)
D6
(D1)
D5
(D2)
D4
(D3)
D3
(D4)
D2
(D5)
D1
(D6)
D0
(D7)
(SDIO_2 PIN)
Figure 47. Single-Bit Serial Mode (3-Wire) Read Timing—Clock Stall Low
INSTRUCTION CYCLE
DATA TRANSFER CYCLE
CS
SCLK
D7
D5
D3
D1
I7
I5
I3
I1
SDIO_1
SDIO_0
(D1) (D3)
(D5)
(D7)
(I1)
(I3)
(I5)
(I7)
I6
(I0)
I4
(I2)
I2
(I4)
I0
(I6)
D6
(D0)
D4
(D2)
D2
(D4)
D0
(D6)
Figure 48. 2-Bit Serial Mode Read Timing—Clock Stall High
INSTRUCTION CYCLE
DATA TRANSFER CYCLE
CS
SCLK
I7
I3
D7
D3
(I3)
(I7)
SDIO_3
SDIO_2
SDIO_1
SDIO_0
(D7)
(D3)
I6
(I2)
I2
(I6)
D6
(D2)
D2
(I6)
I5
(I1)
I1
(I5)
D5
D1
(D1) (D5)
I4
(I0)
I0
(I4)
D4
D0
(D0) (D4)
Figure 49. 4-Bit Serial Mode Read Timing—Clock Stall High
Rev. A | Page 35 of 44
AD9958
REGISTER MAPS AND BIT DESCRIPTIONS
REGISTER MAPS
Table 28. Control Register Map
Register
Name
(Serial
Address)
Bit
Range
Bit 7
(MSB)
Bit 0
(LSB)
Default
Value
Bit 6
Bit 5
Open2
Bit 4
Open2
Bit 3
Bit 2
Bit 1
Channel
Select
[7:0]
Channel 1
enable1
Channel 0
enable1
Must
be 0
Serial I/O mode
select[2:1]
LSB first
0xF0
Register
(CSR)
(0x00)
Function
Register 1
(FR1)
[23:16]
VCO gain
control
PLL divider ratio[22:18]
Charge pump
control[17:16]
0x00
(0x01)
[15:8]
[7:0]
Open
Profile pin configuration (PPC)[14:12]
Ramp-up/
ramp-down
(RU/RD)[11:10]
Modulation level[9:8]
0x00
0x00
0x00
Reference
clock input
power-down
External power-
down mode
SYNC_CLK
disable
DAC reference
power-down
Open[3:2]
Manual
hardware
sync
Manual
software
sync
Function
Register 2
(FR2)
[15:8]
All channels
autoclear
sweep
All channels
clear wweep
accumulator
All channels
autoclear phase
accumulator
All channels
clear phase
accumulator
Open[11:8]
(0x02)
accumulator
[7:0]
Auto sync
enable
Multidevice sync Multidevice sync Multidevice sync
master enable status mask
Open[3:2]
System clock
offset[1:0]
0x00
1 Channel enable bits do not require an I/O update to be activated. These bits are active immediately after the byte containing the bits is written. All other bits need an
I/O update to become active. The two channel enable bits shown in Table 28 are used to enable/disable any combination of the two channels. The default for both
channels is enabled. In readback mode, enable one channel enable bit at a time.
2 This bit must be disabled (Logic 0) in readback mode.
In the channel select register, if the user wants two different
frequencies for the two DDS channels, use the following
protocol:
3. Enable the Channel 1 enable bit only, located in the
channel select Register.
4. Write the desired frequency tuning word for Channel 1 in
Step 3.
1. Enable (Logic 1) the Channel 0 enable bit, which is located
in the channel select register, and disable the Channel 1
enable bit (Logic 0).
2. Write the desired frequency tuning word for Channel 0, as
described in Step 1, and then disable the Channel 0 enable
bit (Logic 0).
Rev. A | Page 36 of 44
AD9958
Table 29. Channel Register Map
Register
Name
(Serial
Address)
Bit
Range
Bit 7
(MSB)
Bit 0
(LSB)
Default
Value
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Open[21:16]
Bit 1
Channel
Function
Register1
(CFR)
[23:16]
[15:8]
Amplitude freq. phase
(AFP) select[23:22]
0x00
Linear
sweep
no-dwell
Linear
sweep
enable
Load SRR at
I/O_UPDATE
Open[12:11]
Must be 0
DAC full-scale current
control[9:8]
0x03
0x02
(0x03)
[7:0]
Digital
power-
down
DAC
power-
down
Matched
pipe delays
active
Autoclear
sweep
accumulator
Clear sweep
accumulator
Autoclear
phase
accumulator
Clear phase
Sine
accumulator2 wave
output
enable
Channel
Frequency
Tuning
[31:24]
[23:16]
[15:8]
[7:0]
Frequency Tuning Word 0[31:24]
Frequency Tuning Word 0[23:16]
Frequency Tuning Word 0[15:8]
Frequency Tuning Word 0[7:0]
0x00
N/A
N/A
N/A
Word 01
(CFTW0)
(0x04)
Channel
Phase
[15:8]
[7:0]
Open[15:14]
Phase Offset Word 0[13:8]
Phase Offset Word 0[7:0]
0x00
0x00
Offset
Word 01
(CPOW0)
(0x05)
Amplitude
Control
Register
(ACR)
[23:16]
[15:8]
Amplitude Ramp Rate[23:16]
N/A
Increment/decrement
step size[15:14]
Open
Amplitude
multiplier
enable
Ramp-up/
ramp-down
enable
Load ARR at
I/O_UPDATE
Amplitude scale
factor[9:8]
0x00
(0x06)
[7:0]
[15:8]
[7:0]
Amplitude scale factor[7:0]
0x00
N/A
N/A
Linear
Sweep
Ramp
Rate1
Falling sweep ramp rate (FSRR)[15:8]
Rising sweep ramp rate (RSRR)[7:0]
(LSRR)
(0x07)
LSR Rising
Delta
[31:24]
[23:16]
[15:8]
[7:0]
Rising delta word[31:24]
Rising delta word[23:16]
Rising delta word[15:8]
Rising delta word[7:0]
N/A
N/A
N/A
N/A
Word1
(RDW)
(0x08)
LSR Falling
Delta
[31:24]
[23:16]
[15:8]
[7:0]
Falling delta word[31:24]
Falling delta word[23:16]
Falling delta word[15:8]
Falling delta word[7:0]
N/A
N/A
N/A
N/A
Word1
(FDW)
(0x09)
1 There are two sets of channel registers and profile registers, one per channel. This is not shown in the Table 29 or Table 30 because the addresses of all channel
registers and profile registers are the same for each channel. Therefore, the channel enable bits (CSR[7:6]) determine if the channel registers and/or profile registers of
each channel are written to or not.
2 The clear phase accumulator bit (CFR[1]) is set to Logic 1 after a master reset. It self-clears or is set to Logic 0 when an I/O update is asserted.
Rev. A | Page 37 of 44
AD9958
Table 30. Profile Register Map1
Bit
Range
Bit 7
(MSB)
Bit 0
(LSB)
Default
Value
Register Name (Address)
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Channel Word 1 (CW1) (0x0A)
Channel Word 2 (CW2) (0x0B)
Channel Word 3 (CW3) (0x0C)
Channel Word 3 (CW4) (0x0D)
Channel Word 5 (CW5) (0x0E)
Channel Word 6 (CW6) (0x0F)
Channel Word 7 (CW7) (0x10)
Channel Word 8 (CW8) (0x11)
Channel Word 9 (CW9) (0x12)
Channel Word 10 (CW10) (0x13)
Channel Word 11 (CW11) (0x14)
Channel Word 12 (CW12) (0x15)
Channel Word 13 (CW13) (0x16)
Channel Word 14 (CW14) (0x17)
Channel Word 15 (CW15) (0x18)
[31:0]
[31:0]
[31:0]
[31:0]
[31:0]
[31:0]
[31:0]
[31:0]
[31:0]
[31:0]
[31:0]
[31:0]
[31:0]
[31:0]
[31:0]
Frequency tuning word[31:0] or phase word[31:18] or amplitude word[31:22]
Frequency tuning word[31:0] or phase word[31:18] or amplitude word[31:22]
Frequency tuning word[31:0] or phase word[31:18] or amplitude word[31:22]
Frequency tuning word[31:0] or phase word[31:18] or amplitude word[31:22]
Frequency tuning word[31:0] or phase word[31:18] or amplitude word[31:22]
Frequency tuning word[31:0] or phase word[31:18] or amplitude word[31:22]
Frequency tuning word[31:0] or phase word[31:18] or amplitude word[31:22]
Frequency tuning word[31:0] or phase word[31:18] or amplitude word[31:22]
Frequency tuning word[31:0] or phase word[31:18] or amplitude word[31:22]
Frequency tuning word[31:0] or phase word[31:18] or amplitude word[31:22]
Frequency tuning word[31:0] or phase word[31:18] or amplitude word[31:22]
Frequency tuning word[31:0] or phase word[31:18] or amplitude word[31:22]
Frequency tuning word[31:0] or phase word[31:18] or amplitude word[31:22]
Frequency tuning word[31:0] or phase word[31:18] or amplitude word[31:22]
Frequency tuning word[31:0] or phase word[31:18] or amplitude word[31:22]
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
1 Each channel word register has a capacity of 32 bits. If phase or amplitude is stored in the channel word registers, it must be first MSB aligned per the bit range.
Only the MSB byte is shown for each channel word register.
Rev. A | Page 38 of 44
AD9958
DESCRIPTIONS FOR CONTROL REGISTERS
Channel Select Register (CSR)—Address 0x00
One byte is assigned to this register.
The CSR determines if channels are enabled or disabled by the status of the two channel enable bits. Both channels are enabled by their
default state. The CSR also determines which serial mode of operation is selected. In addition, the CSR offers a choice of MSB first or LSB
first format.
Table 31. Bit Descriptions for CSR
Bit
Mnemonic
Description
7:6
Channel [1:0] enable
Bits are active immediately after being written. They do not require an I/O update to take effect.
There are two sets of channel registers and profile (channel word) registers, one per channel. This
is not shown in the channel register map or the profile register map. The addresses of all channel
registers and profile registers are the same for each channel. Therefore, the channel enable bits
distinguish the channel registers and profile registers values of each channel. For example,
10 = only Channel 1 receives commands from the channel registers and profile registers.
01 = only Channel 0 receives commands from the channel registers and profile registers.
11 = both Channel 0 and Channel 1 receive commands from the channel registers and profile
registers.
5:4
3
Open
Must be 0
Must be set to 0.
2:1
Serial I/O mode select
00 = single-bit serial (2-wire mode).
01 = single-bit serial (3-wire mode).
10 = 2-bit serial mode.
11 = 4-bit serial mode.
See the Serial I/O Modes of Operation section for more details.
0 = the serial interface accepts serial data in MSB first format (default).
1 = the serial interface accepts serial data in LSB first format.
0
LSB first
Function Register 1 (FR1)—Address 0x01
Three bytes are assigned to this register. FR1 is used to control the mode of operation of the chip.
Table 32. Bit Descriptions for FR1
Bit
Mnemonic
Description
23
VCO gain control
0 = the low range (system clock below 160 MHz) (default).
1 = the high range (system clock above 255 MHz).
22:18 PLL divider ratio
If the value is 4 or 20 (decimal) or between 4 and 20, the PLL is enabled and the value sets the
multiplication factor. If the value is outside of 4 and 20 (decimal), the PLL is disabled.
17:16 Charge pump control
00 (default) = the charge pump current is 75 μA.
01 = charge pump current is 100 μA.
10 = charge pump current is 125 μA.
11 = charge pump current is 150 μA.
15
Open
14:12 Profile pin configuration (PPC)
The profile pin configuration bits control the configuration of the data and SDIO_x pins for the
different modulation modes. See the Modulation Mode section in this document for details.
11:10 Ramp-up/ramp-down (RU/RD) The RU/RD bits control the amplitude ramp-up/ramp-down time of a channel. See the Output
Amplitude Control Mode section for more details.
9:8
Modulation level
The modulation (FSK, PSK, and ASK) level bits control the level (2/4/8/16) of modulation to be
performed for a channel. See the Modulation Mode section for more details.
7
Reference clock input
power-down
0 = the clock input circuitry is enabled for operation (default).
1 = the clock input circuitry is disabled and is in a low power dissipation state.
Rev. A | Page 39 of 44
AD9958
Bit
Mnemonic
Description
6
External power-down mode
0 = the external power-down mode is in fast recovery power-down mode (default). In this mode,
when the PWR_DWN_CTL input pin is high, the digital logic and the DAC digital logic are
powered down. The DAC bias circuitry, PLL, oscillator, and clock input circuitry are not powered
down.
1 = the external power-down mode is in full power-down mode. In this mode, when the
PWR_DWN_CTL input pin is high, all functions are powered down. This includes the DAC and PLL,
which take a significant amount of time to power up.
5
4
SYNC_CLK disable
0 = the SYNC_CLK pin is active (default).
1 = the SYNC_CLK pin assumes a static Logic 0 state (disabled). In this state, the pin drive logic is
shut down. However, the synchronization circuitry remains active internally to maintain normal
device operation.
DAC reference power-down
0 = DAC reference is enabled (default).
1 = DAC reference is powered down.
3:2
1
Open
See the Synchronizing Multiple AD9958 Devices section for details.
0 = the manual hardware synchronization feature of multiple devices is inactive (default).
1 = the manual hardware synchronization feature of multiple devices is active.
0 = the manual software synchronization feature of multiple devices is inactive (default).
Manual hardware sync
0
Manual software sync
1 = the manual software synchronization feature of multiple devices is active. See the
Synchronizing Multiple AD9958 Devices section for details.
Function Register 2 (FR2)—Address 0x02
Two bytes are assigned to this register. The FR2 is used to control the various functions, features, and modes of the AD9958.
Table 33. Bit Descriptions for FR2
Bit
Mnemonic
Description
15
All channels autoclear sweep
accumulator
0 = a new delta word is applied to the input, as in normal operation, but not loaded into the
accumulator (default).
1 = this bit automatically and synchronously clears (loads 0s into) the sweep accumulator for one
cycle upon reception of the I/O_UPDATE sequence indicator on both channels.
14
13
All channels clear
sweep accumulator
All channels autoclear phase
accumulator
0 = the sweep accumulator functions as normal (default).
1 = the sweep accumulator memory elements for both channels are asynchronously cleared.
0 = a new frequency tuning word is applied to the inputs of the phase accumulator, but not
loaded into the accumulator (default).
1 = this bit automatically and synchronously clears (loads 0s into) the phase accumulator for one
cycle upon receipt of the I/O update sequence indicator on both channels.
12
All channels clear phase
Accumulator
0 = the phase accumulator functions as normal (default).
1 = the phase accumulator memory elements for both channels are asynchronously cleared.
11:8
7
6
5
4
Open
Auto sync enable
Multidevice sync master enable
Multidevice sync status
Multidevice sync mask
Open
See the Synchronizing Multiple AD9958 Devices section for more details.
See the Synchronizing Multiple AD9958 Devices section for more details.
See the Synchronizing Multiple AD9958 Devices section for more details.
See the Synchronizing Multiple AD9958 Devices section for more details.
3: 2
1:0
System clock offset
See the Synchronizing Multiple AD9958 Devices section for more details.
Rev. A | Page 40 of 44
AD9958
DESCRIPTIONS FOR CHANNEL REGISTERS
Channel Function Register (CFR)—Address 0x03
Three bytes are assigned to this register.
Table 34. Bit Descriptions for CFR
Bit
Mnemonic
Description
23:22 Amplitude frequency
phase (AFP) select
Controls what type of modulation is to be performed for that channel. See the Modulation Mode section
for details.
21:16 Open
15
14
13
Linear sweep no-dwell
0 = the linear sweep no-dwell function is inactive (default).
1 = the linear sweep no-dwell function is active. If CFR[15] is active, the linear sweep no-dwell function is
activated. See the Linear Sweep Mode section for details. If CFR[14] is clear, this bit is don’t care.
0 = the linear sweep capability is inactive (default).
1 = the linear sweep capability is enabled. When enabled, the delta frequency tuning word is applied to
the frequency accumulator at the programmed ramp rate.
Linear sweep enable
Load SRR at
I/O_UPDATE
0 = the linear sweep ramp rate timer is loaded only upon timeout (timer = 1) and is not loaded because
of an I/O_UPDATE input signal (default).
1 = the linear sweep ramp rate timer is loaded upon timeout (timer = 1) or at the time of an I/O_UPDATE
input signal.
12:11 Open
10
Must be 0
Must be set to 0.
9:8
DAC full-scale current
control
11 = the DAC is at the largest LSB value (default).
See Table 5 for other settings.
7
6
5
Digital power-down
0 = the digital core is enabled for operation (default).
1 = the digital core is disabled and is in its lowest power dissipation state.
0 = the DAC is enabled for operation (default).
1 = the DAC is disabled and is in its lowest power dissipation state.
0 = matched pipe delay mode is inactive (default).
DAC power-down
Matched pipe delays
active
1 = matched pipe delay mode is active. See the Single-Tone Mode—Matched Pipeline Delay section for
details.
4
Autoclear sweep
accumulator
0 = the current state of the sweep accumulator is not impacted by receipt of an I/O_UPDATE signal
(default).
1 = the sweep accumulator is automatically and synchronously cleared for one cycle upon receipt of an
I/O_UPDATE signal.
3
2
Clear sweep
accumulator
Autoclear phase
accumulator
0 = the sweep accumulator functions as normal (default).
1 = the sweep accumulator memory elements are asynchronously cleared.
0 = the current state of the phase accumulator is not impacted by receipt of an I/O_UPDATE signal
(default).
1 = the phase accumulator is automatically and synchronously cleared for one cycle upon receipt of an
I/O_UPDATE signal.
1
0
Clear phase
accumulator
Sine wave output
enable
0 = the phase accumulator functions as normal (default).
1 = the phase accumulator memory elements are asynchronously cleared.
0 = the angle-to-amplitude conversion logic employs a cosine function (default).
1 = the angle-to-amplitude conversion logic employs a sine function.
Rev. A | Page 41 of 44
AD9958
Channel Frequency Tuning Word 0 (CFTW0)—Address 0x04
Four bytes are assigned to this register.
Table 35. Description for CFTW0
Bit
Mnemonic
Description
31:0
Frequency Tuning Word 0 Frequency Tuning Word 0 for each channel.
Channel Phase Offset Word 0 (CPOW0)—Address 0x05
Two bytes are assigned to this register.
Table 36. Description for CPOW0
Bit
Mnemonic
Description
15:14
13:0
Open
Phase Offset Word 0
Phase Offset Word 0 for each channel.
Amplitude Control Register (ACR)—Address 0x06
Three bytes are assigned to this register.
Table 37. Description for ACR
Bit
Mnemonic
Description
23:16
15:14
Amplitude ramp rate
Increment/decrement
step size
Amplitude ramp rate value.
Amplitude increment/decrement step size.
13
12
Open
Amplitude multiplier
enable
0 = amplitude multiplier is disabled. The clocks to this scaling function (auto RU/RD) are stopped
for power saving, and the data from the DDS core is routed around the multipliers (default).
1 = amplitude multiplier is enabled.
11
Ramp-up/ramp-down
enable
This bit is valid only when ACR[12] is active high.
0 = when ACR[12] is active, Logic 0 on ACR[11] enables the manual RU/RD operation. See the
Output Amplitude Control Mode section for details (default).
1 = if ACR[12] is active, a Logic 1 on ACR[11] enables the auto RU/RD operation. See the Output
Amplitude Control Mode section for details.
10
Load ARR at
I/O_UPDATE
0 = the amplitude ramp rate timer is loaded only upon timeout (timer = 1) and is not loaded due
to an I/O_UPDATE input signal (default).
1 = the amplitude ramp rate timer is loaded upon timeout (timer = 1) or at the time of an
I/O_UPDATE input signal.
9:0
Amplitude scale factor
Amplitude scale factor for each channel.
Rev. A | Page 42 of 44
AD9958
Linear Sweep Ramp Rate (LSRR)—Address 0x07
Two bytes are assigned to this register.
Table 38. Description for LSRR
Bit
Mnemonic
Description
15:8
7:0
Falling sweep ramp rate (FSRR)
Rising sweep ramp rate (RSRR)
Linear falling sweep ramp rate.
Linear rising sweep ramp rate.
LSR Rising Delta Word (RDW)—Address 0x08
Four bytes are assigned to this register.
Table 39. Description for RDW
Bit
Mnemonic
Description
31:0
Rising delta word
32-bit rising delta-tuning word.
LSR Falling Delta Word (FDW)—Address 0x09
Four bytes are assigned to this register.
Table 40. Description for FDW
Bit
Mnemonic
Description
31:0
Falling delta word
32-bit falling delta-tuning word.
Rev. A | Page 43 of 44
AD9958
OUTLINE DIMENSIONS
0.30
0.23
0.18
8.00
BSC SQ
0.60 MAX
0.60 MAX
PIN 1
INDICATOR
43
42
56
1
PIN 1
INDICATOR
6.25
6.10 SQ
5.95
TOP
VIEW
EXPOSED
7.75
BSC SQ
PAD
(BOTTOM VIEW)
0.50
0.40
0.30
29
28
14
15
0.25 MIN
6.50
REF
0.80 MAX
0.65 TYP
1.00
0.85
0.80
12° MAX
0.05 MAX
0.02 NOM
THE EXPOSED EPAD ON BOTTOM SIDE
OF PACKAGE IS AN ELECTRICAL
CONNECTION AND MUST BE
COPLANARITY
0.08
SEATING
PLANE
0.50 BSC
SOLDERED TO GROUND.
0.20 REF
COMPLIANT TO JEDEC STANDARDS MO-220-VLLD-2
Figure 50. 56-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
8 mm × 8 mm Body, Very Thin Quad
(CP-56-1)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD9958BCPZ1
AD9958BCPZ-REEL71
AD9958/PCBZ1
Temperature Range
Package Description
Package Option
CP-56-1
CP-56-1
−40°C to +85°C
−40°C to +85°C
56-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
56-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
Evaluation Board
1 Z = RoHS Compliant Part.
©2005–2008 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05252-0-7/08(A)
Rev. A | Page 44 of 44
相关型号:
©2020 ICPDF网 联系我们和版权申明