AD9985ABSTZ-110 [ADI]
110 MSPS/140 MSPS Analog Interface for Flat Panel Displays; 110 MSPS / 140 MSPS模拟接口用于平板显示器
| 型号： | AD9985ABSTZ-110 |
| 厂家： | 
ADI |
| 描述： | 110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
| 文件： | 总32页 (文件大小：629K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
110 MSPS/140 MSPS
Analog Interface for Flat Panel Displays
AD9985A
FEATURES
FUNCTIONAL BLOCK DIAGRAM
Variable analog input bandwidth control
Variable SOGIN bandwidth control
Automated clamping level adjustment
140 MSPS maximum conversion rate
300 MHz analog bandwidth
0.5 V to 1.0 V analog input range
500 ps p-p PLL clock jitter at 110 MSPS
3.3 V power supply
Full sync processing
Selectable input filtering
Sync detect for hot plugging
Midscale clamping
AUTO-CLAMP
LEVEL ADJUST
8
R
G
B
A/D
A/D
A/D
R
OUTA
CLAMP
CLAMP
CLAMP
IN
IN
IN
AUTO-CLAMP
LEVEL ADJUST
8
8
G
OUTA
AUTO-CLAMP
LEVEL ADJUST
B
OUTA
Power-down mode
Low power: 500 mW typical
4:2:2 output format mode
MIDSCV
HSYNC
COAST
CLAMP
FILT
DTACK
HSOUT
VSOUT
SOGOUT
SYNC
PROCESSING
AND CLOCK
GENERATION
APPLICATIONS
SOGIN
RGB graphics processing
LCD monitors and projectors
Plasma display panels
Scan converters
REF
BYPASS
REF
SCL
SDA
A0
SERIAL REGISTER AND
POWER MANAGEMENT
AD9985A
Microdisplays
Digital TVs
Figure 1.
GENERAL DESCRIPTION
The AD9985A is a complete 8-bit, 140 MSPS, monolithic
analog interface optimized for capturing RGB graphics signals
from personal computers and workstations. Its 140 MSPS
encode rate capability and full power analog bandwidth of 300
MHz support resolutions up to SXGA (1280 × 1024 at 75 Hz).
When the Coast signal is presented, the PLL maintains its
output frequency in the absence of Hsync. A sampling phase
adjustment is provided. Data, Hsync, and clock output phase
relationships are maintained. The AD9985A also offers full sync
processing for composite sync and sync-on-green applications.
The AD9985A includes a 140 MHz triple ADC with internal
1.25 V reference, a PLL, and programmable gain, offset, and
clamp control. The user provides only a 3.3 V power supply,
analog input, and horizontal sync (Hsync) and Coast signals.
Three-state CMOS outputs can be powered from 2.5 V to 3.3 V.
A clamp signal is generated internally or can be provided by the
user through the CLAMP input pin. This interface is fully
programmable via a 2-wire serial interface.
Fabricated in an advanced CMOS process, the AD9985A is
provided in a space-saving 80-lead LQFP surface-mount
Pb-free plastic package, and is specified over the –40°C to
+85°C temperature range.
The AD9985A’s on-chip PLL generates a pixel clock from the
Hsync input. Pixel clock output frequencies range from 12 MHz
to 140 MHz. PLL clock jitter is 500 ps p-p typical at 140 MSPS.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
© 2005 Analog Devices, Inc. All rights reserved.
AD9985A
TABLE OF CONTENTS
Specifications..................................................................................... 3
Hsync Timing ............................................................................. 15
Coast Timing .............................................................................. 16
2-Wire Serial Register Map ........................................................... 17
2-Wire Serial Control Register Detail Chip Identification... 19
PLL Divider Control .................................................................. 19
Clock Generator Control .......................................................... 20
Clamp Timing............................................................................. 20
Hsync Pulse Width..................................................................... 20
Input Gain ................................................................................... 20
Input Offset ................................................................................. 21
Mode Control 1 .......................................................................... 21
2-Wire Serial Control Port............................................................ 26
Data Transfer via Serial Interface............................................. 26
Sync Slicer.................................................................................... 28
Sync Separator ............................................................................ 28
PCB Layout Recommendations.................................................... 29
Analog Interface Inputs............................................................. 29
Power Supply Bypassing............................................................ 29
PLL ............................................................................................... 29
Outputs (Both Data and Clocks).............................................. 30
Digital Inputs .............................................................................. 30
Voltage Reference ....................................................................... 30
Outline Dimensions....................................................................... 31
Ordering GuIde .......................................................................... 31
Explanation of Test Levels........................................................... 6
Absolute Maximum Ratings............................................................ 7
ESD Caution.................................................................................. 7
Pin Configuration and Function Descriptions............................. 8
Design Guide................................................................................... 11
General Description................................................................... 11
Digital Inputs .............................................................................. 11
Input Signal Handling................................................................ 11
Hsync, Vsync Inputs .................................................................. 11
Serial Control Port ..................................................................... 11
Output Signal Handling............................................................. 11
Clamping ..................................................................................... 11
RGB Clamping........................................................................ 11
YUV Clamping....................................................................... 12
Gain and Offset Control............................................................ 12
Auto Offset.............................................................................. 12
Sync-on-Green............................................................................ 13
Clock Generation ....................................................................... 13
12-Bit Divisor Register .......................................................... 14
2-Bit VCO Range Register .................................................... 14
3-Bit Charge Pump Current Register .................................. 14
5-Bit Phase Adjust Register................................................... 14
Power Management.................................................................... 14
Timing.......................................................................................... 15
REVISION HISTORY
7/05—Revision 0: Initial Version
Rev. 0 | Page 2 of 32
AD9985A
SPECIFICATIONS
VD = 3.3 V, VDD = 3.3 V, ADC clock = maximum conversion rate, unless otherwise noted.
Table 1.
AD9985AKSTZ-110
AD9985AKSTZ-140
Parameter
Temp Test Level Min
Typ
Max
Min
Typ
Max
Unit
RESOLUTION
8
8
Bits
DC ACCURACY
Differential Nonlinearity
25°C
Full
25°C
Full
I
VI
I
VI
VI
0.5
0.5
+1.25/−1.0
+1.35/−1.0
1.85
0.5
0.5
+1.35/−1.0 LSB
1.ꢀ5/−1.0 LSB
Integral Nonlinearity
2.0
2.3
LSB
LSB
2.0
No Missing Codes
ANALOG INPUT
Input Voltage Range
Minimum
Maximum
Gain Tempco
Full
Guaranteed
Guaranteed
Full
Full
25°C
25°C
Full
Full
Full
Full
VI
VI
V
IV
IV
V
0.5
0.5
V p-p
V p-p
ppm/°C
μA
1.0
1.0
100
100
Input Bias Current
1
1
1
1
μA
Input Offset Voltage
Input Full-Scale Matching
Offset Adjustment Range
REFERENCE OUTPUT
Output Voltage
Temperature Coefficient
SWITCHING PERFORMANCE
Maximum Conversion Rate
Minimum Conversion Rate
Data to Clock Skew
tBUFF
tSTAH
tDHO
tDAL
tDAH
tDSU
tSTASU
tSTOTSU
7
7
mV
VI
VI
1.5
ꢀ9
8.0
52
1.5
ꢀ9
8.0
52
%FS
%FS
ꢀ6
ꢀ6
Full
Full
V
V
1.25
50
1.25
50
V
ppm/°C
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
25°C
Full
Full
VI
IV
IV
VI
VI
VI
VI
VI
VI
VI
VI
IV
VI
IV
IV
IV
IV
110
1ꢀ0
MSPS
MSPS
ns
10
+2.0
10
+2.0
−0.5
ꢀ.7
ꢀ.0
300
ꢀ.7
ꢀ.0
250
ꢀ.7
ꢀ.0
15
−0.5
ꢀ.7
ꢀ.0
300
ꢀ.7
ꢀ.0
250
ꢀ.7
ꢀ.0
15
μs
μs
ns
μs
μs
ns
μs
μs
HSYNC Input Frequency
Maximum PLL Clock Rate
Minimum PLL Clock Rate
PLL Jitter
110
110
kHz
MHz
MHz
ps p-p
ps p-p
ps/°C
110
1ꢀ0
12
7001
10001
12
7001
7001
ꢀ00
15
ꢀ00
ꢀ00
15
Sampling Phase Tempco
DIGITAL INPUTS
Input Voltage, High (VIH)
Input Voltage, Low (VIL)
Input Current, High (VIH)
Input Current, Low (VIL)
Input Capacitance
Full
Full
Full
Full
25°C
VI
VI
V
V
V
2.5
2.5
V
V
μA
μA
pF
0.8
−1.0
+1.0
0.8
−1.0
+1.0
3
3
Rev. 0 | Page 3 of 32
AD9985A
AD9985AKSTZ-110
AD9985AKSTZ-140
Parameter
Temp Test Level Min
Typ
Max
Min
Typ
Max
Unit
DIGITAL OUTPUTS
VD − 0.1
ꢀ5
Output Voltage, High (VOH)
Output Voltage, Low (VOL)
Duty Cycle DATACK
Output Coding
Full
Full
Full
VI
VI
IV
VD − 0.1
ꢀ5
V
0.1
55
0.1
55
V
%
50
Binary
50
Binary
POWER SUPPLY
VD Supply Voltage
Full
Full
Full
25°C
25°C
25°C
Full
IV
IV
IV
V
V
V
VI
VI
VI
3.15
2.2
3.15
3.3
3.3
3.3
132
19
8
525
5
3.ꢀ5
3.ꢀ5
3.ꢀ5
3.15
2.2
3.15
3.3
3.3
3.3
180
26
11
650
5
3.ꢀ5
3.ꢀ5
3.ꢀ5
V
V
V
mA
mA
mA
mW
mA
mW
VDD Supply Voltage
PVD Supply Voltage
ID Supply Current (VD)
IDD Supply Current (VDD)2
IPVD Supply Current (PVD)
Total Power Dissipation
Power-Down Supply Current Full
Power-Down Dissipation
DYNAMIC PERFORMANCE
760
15
50
900
15
50
Full
16.5
16.5
Analog Bandwidth, Full
Power
Transient Response
Overvoltage Recovery
Time
25°C
25°C
25°C
V
V
V
300
2
300
2
MHz
ns
1.5
1.5
ns
Signal-to-Noise Ratio (SNR)
(Without Harmonics)
fIN = ꢀ0.7 MHz
25°C
Full
V
V
ꢀꢀ
ꢀ3
ꢀ3
ꢀ2
dB
dB
Crosstalk
Full
V
55
55
dBc
THERMAL CHARACTERISTICS
θJC Junction-to-Case
Thermal Resistance
θJA Junction-to-Ambient
Thermal Resistance
V
V
16
35
16
35
°C/W
°C/W
1 VCO range = 10, charge pump current = 110, PLL divider = 1693.
2 DATACK load = 15 pF, data load = 5 pF.
Rev. 0 | Page ꢀ of 32
AD9985A
VD = 3.3 V, VDD = 3.3 V, ADC clock = maximum conversion rate, unless otherwise noted.
Table 2.
Test
AD9985ABSTZ-110
Parameter
Temp
Level
Min
Typ
Max
Unit
Bits
LSB
LSB
LSB
LSB
RESOLUTION
8
DC ACCURACY
Differential Nonlinearity
25°C
Full
25°C
Full
I
VI
I
0.5
0.5
+1.25/−1.0
+1.5/−1.0
1.85
Integral Nonlinearity
VI
3.2
ANALOG INPUT
Input Voltage Range
Minimum
Maximum
Gain Tempco
Input Bias Current
Full
Full
25°C
25°C
Full
Full
Full
Full
VI
VI
V
IV
IV
VI
VI
VI
0.5
V p-p
V p-p
ppm/°C
μA
μA
mV
1.0
100
1
2
Input Offset Voltage
Input Full-Scale Matching
Offset Adjustment Range
REFERENCE OUTPUT
Output Voltage
Temperature Coefficient
SWITCHING PERFORMANCE
Maximum Conversion Rate
Minimum Conversion Rate
Data-to-Clock Skew
tBUFF
tSTAH
tDHO
tDAL
tDAH
tDSU
tSTASU
tSTAH
7
1.5
ꢀ9
8.0
52
% FS
% FS
ꢀ6
Full
Full
VI
V
1.25
100
V
ppm/°C
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
25°C
Full
Full
VI
IV
IV
VI
VI
VI
VI
VI
VI
VI
VI
IV
VI
IV
IV
IV
IV
110
MSPS
MSPS
ns
μs
μs
ns
μs
μs
ns
10
+2.0
−0.5
ꢀ.7
ꢀ.0
300
ꢀ.7
ꢀ.0
250
ꢀ.7
μs
μs
HSYNC Input Frequency
Maximum PLL Clock Rate
Minimum PLL Clock Rate
PLL Jitter
15
110
110
kHz
MHz
MHz
ps p-p
ps p-p
ps/°C
12
7001
10001
ꢀ00
15
Sampling Phase Tempco
DIGITAL INPUTS
Input Voltage, High (VIH)
Input Voltage, Low (VIL)
Input Current, High (IIH)
Input Current, Low (IIL)
Input Capacitance
Full
Full
Full
Full
25°C
VI
VI
V
V
V
2.5
V
V
μA
μA
pF
0.8
−1.0
1.0
3
DIGITAL OUTPUTS
Output Voltage, High (VOH)
Output Voltage, Low (VOL)
Duty Cycle, DATACK
Output Coding
Full
Full
Full
VI
VI
IV
VD − 0.1
ꢀ5
V
V
%
0.1
55
50
Binary
Rev. 0 | Page 5 of 32
AD9985A
Test
AD9985ABSTZ-110
Parameter
Temp
Level
Min
Typ
Max
Unit
POWER SUPPLY
VD Supply Voltage
VDD Supply Voltage
PVD Supply Voltage
Full
Full
Full
25°C
25°C
25°C
Full
Full
Full
IV
IV
IV
V
V
V
VI
VI
VI
3.15
2.2
3.15
3.3
3.3
3.3
132
19
8
525
5
3.ꢀ5
3.ꢀ5
3.ꢀ5
V
V
V
mA
mA
mA
mW
mA
mW
ID Supply Current (VD)
IDD Supply Current (VDD)2
IPVD Supply Current (PVD)
Total Power Dissipation
Power-Down Supply Current
Power-Down Dissipation
DYNAMIC PERFORMANCE
Analog Bandwidth, Full Power
Transient Response
Overvoltage Recovery Time
Signal-to-Noise Ratio (SNR)
(Without Harmonics)
fIN = ꢀ0.7 MHz
760
15
50
16.5
25°C
25°C
25°C
25°C
Full
V
V
V
V
V
300
2
1.5
ꢀꢀ
ꢀ3
MHz
ns
ns
dB
dB
Crosstalk
Full
V
55
dBc
THERMAL CHARACTERISTICS
θJC Junction-to-Case
Thermal Resistance
θJA Junction-to-Ambient
Thermal Resistance
V
V
16
35
°C/W
°C/W
1 VCO range = 10, charge pump current = 110, PLL divider = 1693.
2 DATACK load = 15 pF, data load = 5 pF.
EXPLANATION OF TEST LEVELS
I.
II.
100% production tested.
100% production tested at 25°C and sample tested at specified temperatures.
III. Sample tested only.
IV. Parameter is guaranteed by design and characterization testing.
V.
Parameter is a typical value only.
VI. 100% production tested at 25°C; guaranteed by design and characterization testing.
Rev. 0 | Page 6 of 32
AD9985A
ABSOLUTE MAXIMUM RATINGS
Table 3.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum ratings for extended periods may affect device
reliability.
Parameter
Rating
VD
VDD
3.6 V
3.6 V
Analog Inputs
Digital Inputs
VD to 0.0 V
5 V to 0.0 V
20 mA
−ꢀ0°C to +85°C
−65°C to +150°C
150°C
Digital Output Current
Operating Temperature
Storage Temperature
Maximum Junction Temperature
Maximum Case Temperature
150°C
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as ꢀ000 V readily accumulate on the
human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 7 of 32
AD9985A
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
1
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
GND
GND
PIN 1
2
GREEN <7>
V
D
3
GREEN <6>
GREEN <5>
GREEN <4>
GREEN <3>
GREEN <2>
GREEN <1>
GREEN <0>
GND
REF BYPASS
4
SDA
SCL
A0
5
6
7
R
IN
AD9985A
TOP VIEW
(Not to Scale)
8
GND
9
V
D
10
11
12
13
14
15
16
17
18
19
20
V
D
V
GND
DD
BLUE <7>
BLUE <6>
BLUE <5>
BLUE <4>
BLUE <3>
BLUE <2>
BLUE <1>
BLUE <0>
GND
SOGIN
G
IN
GND
V
V
D
D
GND
B
IN
D
V
GND
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
Figure 2. Pin Configuration
Table 4. Complete Pinout List
Pin Type
Mnemonic
Function
Value
Pin No.
Inputs
RIN
GIN
BIN
Analog Input for Converter R
Analog Input for Converter G
Analog Input for Converter B
Horizontal SYNC Input
Vertical SYNC Input
Input for Sync-on-Green
0.0 V to 1.0 V
0.0 V to 1.0 V
0.0 V to 1.0 V
3.3 V CMOS
3.3 V CMOS
0.0 V to 1.0 V
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
5ꢀ
ꢀ8
ꢀ3
30
31
ꢀ9
38
29
HSYNC
VSYNC
SOGIN
CLAMP
COAST
Red [7:0]
Green [7:0]
Blue [7:0]
DATACK
HSOUT
VSOUT
SOGOUT
Clamp Input (External Clamp Signal)
PLL Coast Signal Input
Outputs
Outputs of Converter Red, Bit 7 is the MSB
Outputs of Converter Green, Bit 7 is the MSB
Outputs of Converter Blue, Bit 7 is the MSB
Data Output Clock
HSYNC Output (Phase-Aligned with DATACK) 3.3 V CMOS
VSYNC Output (Phase-Aligned with DATACK) 3.3 V CMOS
70 to 77
2 to 9
12 to 19
67
66
6ꢀ
Sync-on-Green Slicer Output
3.3 V CMOS
1.25 V
65
References
REF BYPASS Internal Reference Bypass
58
MIDSCV
FILT
Internal Midscale Voltage Bypass
Connection for External Filter Components
for Internal PLL
37
33
Rev. 0 | Page 8 of 32
AD9985A
Pin Type
Mnemonic
VD
VDD
PVD
GND
Function
Value
3.3 V
3.3 V
3.3 V
0 V
Pin No.
Power Supply
Analog Power Supply
Output Power Supply
PLL Power Supply
Ground
26, 27, 39, ꢀ2, ꢀ5, ꢀ6, 51, 52, 59, 62
11, 22, 23, 69, 78, 79
3ꢀ, 35
1, 10, 20, 21, 2ꢀ, 25, 28, 32, 36, ꢀ0, ꢀ1,
ꢀꢀ, ꢀ7, 50, 53, 60, 61, 63, 68, 80
Serial Port (2-Wire) SDA
Serial Port Data I/O
Serial Port Data Clock (100 kHz maximum)
Serial Port Address Input 1
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
57
56
55
SCL
A0
Table 5. Pin Function Descriptions
Pin
Inputs
RIN
Description
Analog Input for Red Channel.
Analog Input for Green Channel.
GIN
BIN
Analog Input for Blue Channel. High impedance inputs that accept the red, green, and blue channel graphics
signals, respectively. (The three channels are identical, and can be used for any colors, but colors are assigned for
convenient reference.) They accommodate input signals ranging from 0.5 V to 1.0 V full scale. Signals should be
ac-coupled to these pins to support clamp operation.
HSYNC
Horizontal Sync Input. This input receives a logic signal that establishes the horizontal timing reference and
provides the frequency reference for pixel clock generation. The logic sense of this pin is controlled by serial
Register 0x0E, Bit 6 (Hsync polarity). Only the leading edge of Hsync is active; the trailing edge is ignored. When
Hsync polarity = 0, the falling edge of Hsync is used. When Hsync polarity = 1, the rising edge is active. The input
includes a Schmitt trigger for noise immunity, with a nominal input threshold of 1.5 V.
VSYNC
SOGIN
Vertical Sync Input. This is the input for vertical sync.
Sync-on-Green Input. This input is provided to assist with processing signals with embedded sync, typically on the
green channel. The pin is connected to a high speed comparator with an internally generated threshold. The
threshold level can be programmed in 10 mV steps to any voltage between 10 mV and 330 mV above the
negative peak of the input signal. The default voltage threshold is 150 mV. When connected to an ac-coupled
graphics signal with embedded sync, it produces a noninverting digital output on SOGOUT. (This is usually a
composite sync signal, containing both vertical and horizontal sync information that must be separated before
passing the horizontal sync signal to Hsync.) When not used, this input should be left unconnected. For more
details on this function and how it should be configured, refer to the Sync-on-Green section.
CLAMP
COAST
External Clamp Input. This logic input can be used to define the time during which the input signal is clamped to
ground. It should be exercised when the reference dc level is known to be present on the analog input channels,
typically during the back porch of the graphics signal. The CLAMP pin is enabled by setting control bit clamp
function to 1, (Register 0x0F, Bit 7, default is 0). When disabled, this pin is ignored and the clamp timing is
determined internally by counting a delay and duration from the trailing edge of the Hsync input. The logic sense
of this pin is controlled by clamp polarity Register 0x0F, Bit 6. When not used, this pin must be grounded and
clamp function programmed to 0.
Clock Generator Coast Input (Optional). This input can be used to cause the pixel clock generator to stop
synchronizing with Hsync and continue producing a clock at its current frequency and phase. This is useful when
processing signals from sources that fail to produce horizontal sync pulses during the vertical interval. The Coast
signal is generally not required for PC-generated signals. The logic sense of this pin is controlled by Coast polarity
(Register 0x0F, Bit 3). When not used, this pin can be grounded and Coast polarity programmed to 1, or tied high
(to VD through a 10 kΩ resistor) and Coast polarity programmed to 0. Coast polarity defaults to 1 at power-up.
Outputs
HSOUT
Horizontal Sync Output. A reconstructed and phase-aligned version of the Hsync input. Both the polarity and
duration of this output can be programmed via serial bus registers. By maintaining alignment with DATACK and
Data outputs, data timing with respect to horizontal sync can always be determined.
VSOUT
Vertical Sync Output. A reconstructed and phase-aligned version of the video Vsync. The polarity of this output
can be controlled via a serial bus bit. The placement and duration in all modes is set by the graphics transmitter.
SOGOUT
Sync-on-Green Slicer Output. This pin outputs either the signal from the sync-on-green slicer comparator or an
unprocessed but delayed version of the Hsync input. See the sync processing block diagram (Figure 1ꢀ) to view
how this pin is connected. (Apart from slicing off SOG, the output from this pin gets no other additional process-
ing on the AD9985A. Vsync separation is performed via the sync separator.)
Rev. 0 | Page 9 of 32
AD9985A
Pin
Description
Data Outputs
RED
GREEN
BLUE
Data Output, Red Channel.
Data Output, Green Channel.
Data Output, Blue Channel. The main data outputs. Bit 7 is the MSB. The delay from pixel sampling time to output
is fixed. When the sampling time is changed by adjusting the phase register, the output timing is shifted as well.
The DATACK and HSOUT outputs are also moved, so the timing relationship among the signals is maintained. For
exact timing information, refer to Figure 9, Figure 10, and Figure 11.
Data Clock Output
DATACK
Data Output Clock. This is the main clock output signal used to strobe the output data and HSOUT into external
logic. It is produced by the internal clock generator and is synchronous with the internal pixel sampling clock.
When the sampling time is changed by adjusting the phase register, the output timing is shifted as well. The Data,
DATACK, and HSOUT outputs are all moved, so the timing relationship among the signals is maintained.
References
REF BYPASS
Internal Reference Bypass. Bypass for the internal 1.25 V band gap reference. It should be connected to ground
through a 0.1 μF capacitor. The absolute accuracy of this reference is ꢀ%, and the temperature coefficient is 50
ppm, which is adequate for most AD9985A applications. If higher accuracy is required, an external reference can
be used instead.
MIDSCV
FILT
Midscale Voltage Reference Bypass. Bypass for the internal midscale voltage reference. It should be connected to
ground through a 0.1 μF capacitor. The exact voltage varies with the gain setting of the blue channel.
External Filter Connection. For proper operation, the pixel clock generator PLL requires an external filter. Connect
the filter shown in Figure 6 to this pin. For optimal performance, minimize noise and parasitics on this node.
Power Supply
VD
Main Power Supply. These pins supply power to the main elements of the circuit. They should be filtered and kept
as quiet as possible.
VDD
Digital Output Power Supply. A large number of output pins (up to 25) switching at high speed (up to 110 MHz)
generates a lot of power supply transients (noise). These supply pins are identified separately from the VD pins so
special care can be taken to minimize output noise transferred into the sensitive analog circuitry. If the AD9985A
is interfacing with lower voltage logic, VDD can be connected to a lower supply voltage (as low as 2.5 V) for
compatibility.
PVD
Clock Generator Power Supply. The most sensitive portion of the AD9985A is the clock generation circuitry. These
pins provide power to the clock PLL and help the user design for optimal performance. The designer should
provide quiet, noise-free power to these pins.
GND
Ground. The ground return for all circuitry on-chip. It is recommended that the AD9985A be assembled on a
single solid ground plane, with careful attention given to ground current paths.
Serial Port (2-Wire)
SDA
SCL
Serial Port Data I/O.
Serial Port Data Clock.
Serial Port Address Input 1. For a full description of the 2-wire serial register and how it works, refer to the 2-Wire
Serial Control Port section.
A0
Rev. 0 | Page 10 of 32
AD9985A
DESIGN GUIDE
GENERAL DESCRIPTION
The AD9985A is a fully integrated solution for capturing analog
RGB signals and digitizing them for display on flat panel moni-
tors or projectors. The circuit is ideal for providing a computer
interface for HDTV monitors or as the front end to high
performance video scan converters. Implemented in a high
performance CMOS process, the interface can capture signals
with pixel rates up to 110 MHz.
is effective in rolling off the input bandwidth slightly and
providing a high quality signal over a wider range of conditions.
Using a Fair-Rite #2508051217Z0 High Speed Signal Chip Bead
inductor in the circuit of Figure 3 yields good results in most
applications.
47nF
R
IN
RGB
INPUT
G
IN
IN
B
75Ω
The AD9985A includes all necessary input buffering, signal dc
restoration (clamping), offset and gain (brightness and contrast)
adjustment, pixel clock generation, sampling phase control, and
output data formatting. All controls are programmable via a
2-wire serial interface. Full integration of these sensitive analog
functions makes system design straightforward and less
sensitive to the physical and electrical environment.
Figure 3. Analog Input Interface Circuit
HSYNC, VSYNC INPUTS
The interface also takes a horizontal sync signal, which is used
to generate the pixel clock and clamp timing. This can be either
a sync signal directly from the graphics source, or a preproc-
essed TTL or CMOS level signal.
With a typical power dissipation of only 500 mW and an
operating temperature range of 0°C to 70°C (−40°C to +85°C
for the AD9985ABST), the device requires no special
environmental considerations.
The Hsync input includes a Schmitt trigger buffer for immunity
to noise and signals with long rise times. In typical PC-based
graphic systems, the sync signals are simply TTL-level drivers
feeding unshielded wires in the monitor cable. As such, no
termination is required.
DIGITAL INPUTS
All digital inputs on the AD9985A operate to 3.3 V CMOS
levels. However, all digital inputs are 5 V tolerant. Applying 5 V
to them does not cause any damage.
SERIAL CONTROL PORT
The serial control port is designed for 3.3 V logic. If there are
5 V drivers on the bus, these pins should be protected with
150 Ω series resistors placed between the pull-up resistors and
the input pins.
INPUT SIGNAL HANDLING
The AD9985A has one high impedance analog input pin for
each of the red, green, and blue channels. They accommodate
signals ranging from 0.5 V to 1.0 V p-p.
OUTPUT SIGNAL HANDLING
The digital outputs are designed and specified to operate from a
3.3 V power supply (VDD). They can also work with a VDD as low
as 2.5 V for compatibility with other 2.5 V logic.
Signals are typically brought onto the interface board via a
DVI-I connector, a 15-pin D connector, or via BNC connectors.
The AD9985A should be located as close as practical to the
input connector. Signals should be routed via matched-
impedance traces (normally 75 Ω) to the IC input pins.
CLAMPING
RGB Clamping
At this point, the signal should be resistively terminated (75 Ω
to the signal ground return) and capacitively coupled to the
AD9985A inputs through 47 nF capacitors. These capacitors
form part of the dc restoration circuit.
To properly digitize the incoming signal, the dc offset of the
input must be adjusted to fit the range of the on-board ADCs.
Most graphics systems produce RGB signals with black at
ground and white at approximately 0.75 V. However, if sync
signals are embedded in the graphics, the sync tip is often at
ground, black is at 300 mV, and white is at approximately 1.0 V.
Some common RGB line amplifier boxes use emitter-follower
buffers to split signals and increase drive capability. This
introduces a 700 mV dc offset to the signal, which must be
removed for proper capture by the AD9985A.
When impedances are perfectly matched, the best performance
can be obtained with the widest possible signal bandwidth. The
ultrawide bandwidth inputs of the AD9985A (300 MHz) can
track the input signal continuously as it moves from one pixel
level to the next, and digitize the pixel during a long, flat pixel
time. In many systems, however, there are mismatches,
reflections, and noise, which can result in excessive ringing and
distortion of the input waveform. This makes it more difficult
to establish a sampling phase that provides good image quality.
It has been shown that a small inductor in series with the input
The key to clamping is to identify a portion (time) of the signal
when the graphic system is known to be producing black. An
offset is then introduced that results in the ADCs producing a
Rev. 0 | Page 11 of 32
AD9985A
black output (code 0x00) when the known black input is
present. The offset then remains in place when other signal
levels are processed, and the entire signal is shifted to eliminate
offset errors.
range of the ADC range (0x80) rather than at the bottom of the
ADC converter range (0x00).
Clamping to midscale rather than to ground can be accom-
plished by setting the clamp select bits in the serial bus register.
Each of the three converters has its own selection bit so that
they can be clamped to either midscale or ground independ-
ently. These bits are located in Register 0x10, Bits [2:0]. The
midscale reference voltage that each ADC clamps to is provided
on the MIDSCV pin (Pin 37). This pin should be bypassed to
ground with a 0.1 μF capacitor, even if midscale clamping is not
required.
In most PC graphics systems, black is transmitted between
active video lines. With CRT displays, when the electron beam
has completed writing a horizontal line on the screen (at the
right side), the beam is deflected quickly to the left side of the
screen (called horizontal retrace), and a black signal is provided
to prevent the beam from disturbing the image.
In systems with embedded sync, a blacker-than-black signal
(Hsync) is produced briefly to signal the CRT that it is time to
begin a retrace. For obvious reasons, it is important to avoid
clamping on the tip of Hsync. Fortunately, there is virtually
always a period following Hsync, called the back porch, when a
good black reference is provided. This is the time when clamp-
ing should be performed.
GAIN AND OFFSET CONTROL
The AD9985A can accommodate input signals with inputs
ranging from 0.5 V to 1.0 V full scale. The full-scale range is set
in three 8-bit registers (red gain, green gain, and blue gain).
Note that increasing the gain setting results in an image with
less contrast.
The clamp timing can be established by simply exercising the
CLAMP pin at the appropriate time (with External Clamp = 1).
The polarity of this signal is set by the clamp polarity bit.
The offset control shifts the entire input range, resulting in a
change in image brightness. Three 7-bit registers (red offset,
green offset, blue offset) provide independent settings for each
channel. The offset controls provide a 63 LSB adjustment
range. This range is connected with the full-scale range, so if the
input range is doubled (from 0.5 V to 1.0 V), the offset step size
is also doubled (from 2 mV per step to 4 mV per step).
A simpler method of clamp timing uses the AD9985A internal
clamp timing generator. The clamp placement register is pro-
grammed with the number of pixel times that should pass after
the trailing edge of Hsync before clamping starts. A second
register (clamp duration) sets the duration of the clamp. These
are both 8-bit values, which provide considerable flexibility in
clamp generation. The clamp timing is referenced to the trailing
edge of Hsync because, though Hsync duration can vary widely,
the back porch (black reference) always follows Hsync. A good
starting point for establishing clamping is to set the clamp
placement to 0x09 (providing 9 pixel periods for the graphics
signal to stabilize after sync) and set the clamp duration to 0x14
(giving the clamp 20 pixel periods to re-establish the black
reference).
Figure 4 shows the interaction of gain and offset controls. The
magnitude of an LSB in offset adjustment is proportional to the
full-scale range, so changing the full-scale range also changes
the offset. The change is minimal if the offset setting is near
midscale. When changing the offset, the full-scale range is not
affected, but the full-scale level is shifted by the same amount as
the zero-scale level.
OFFSET = 7FH
OFFSET = 3FH
1.0
Clamping is accomplished by placing an appropriate charge on
the external input coupling capacitor. The value of this
capacitor affects the performance of the clamp. If it is too small,
there is a significant amplitude change during a horizontal line
time (between clamping intervals). If the capacitor is too large,
it takes excessively long for the clamp to recover from a large
change in incoming signal offset. The recommended value
(47 nF) results in recovering from a step error of 100 mV to
within 1/2 LSB in 10 lines with a clamp duration of 20 pixel
periods on a 60 Hz SXGA signal.
OFFSET = 00H
0.5
OFFSET = 7FH
OFFSET = 3FH
0
OFFSET = 00H
00H
FFH
GAIN
YUV Clamping
Figure 4. Gain and Offset Control
YUV graphics signals are slightly different from RGB signals, as
the dc reference level (black level in RGB signals) can be at the
midpoint of the graphics signal rather than at the bottom. For
these signals, it might be necessary to clamp to the midscale
Auto Offset
In addition to the manual offset adjustment mode (via registers
0x0B to 0x0D), the AD9985A also includes circuitry to auto-
matically calibrate the offset for each channel. By monitoring
Rev. 0 | Page 12 of 32
AD9985A
47nF
47nF
47nF
1nF
the output of each ADC during the back porch of the input
signals, the AD9985A can self-adjust to eliminate any offset
errors in its own ADC channels, as well as any offset errors
present on the incoming graphics or video signals.
R
B
IN
IN
G
IN
To activate the auto offset mode, set Register 0x1D, Bit 7 to 1.
Next, the target code registers (0x19 through 0x1B) must be
programmed. The values programmed into the target code
registers should be the output code desired from the AD9985A
during the back porch reference time. For example, for RGB
signals, all three registers are normally programmed to code 1,
while for YPbPr signals, the green (Y) channel is normally
programmed to code 1, and the blue and red channels (Pb and
Pr) are normally set to 128. Any target code value between 1
and 254 can be set, although the AD9985A’s offset range may
not be able to reach every value. Intended target code values
range from (but are not limited to) 1 to 40 when ground
clamping, and 90 to 170 when midscale clamping.
SOG
Figure 5. Typical Clamp Configuration
CLOCK GENERATION
A phase-locked loop (PLL) is used to generate the pixel clock.
In this PLL, the Hsync input provides a reference frequency. A
voltage controlled oscillator (VCO) generates a much higher
pixel clock frequency. This pixel clock is divided by the PLL
divide value (Register 0x01 and Register 0x02) and phase
compared with the Hsync input. Any error is used to shift the
VCO frequency and maintain lock between the two signals.
The stability of this clock is a very important element in provid-
ing the clearest and most stable image. During each pixel time,
there is a period during which the signal is slewing from the old
pixel amplitude and settling at its new value. Then, there is a
time when the input voltage is stable before the signal must slew
to a new value (Figure 6). The ratio of the slewing time to the
stable time is a function of the bandwidth of the graphics DAC
and the bandwidth of the transmission system (cable and
termination). It is also a function of the overall pixel rate.
Clearly, if the dynamic characteristics of the system remain
fixed, the slewing and settling time is, likewise, fixed. This time
must be subtracted from the total pixel period, leaving the
stable period. At higher pixel frequencies, the total cycle time is
shorter, and the stable pixel time also becomes shorter.
The ability to program a target code for each channel gives
users a large degree of freedom and flexibility. While in most
cases all channels are set either to 1 or 128, the flexibility to
select other values allows the possibility of inserting intentional
skews between channels. It also allows the ADC range to be
skewed so that voltages outside of the normal range can be
digitized. For example, setting the target code to 40 allows the
sync tip, which is normally below black level, to be digitized and
evaluated.
Lastly, when in auto offset mode, the manual offset registers
(0x0B to 0x0D) have new functionality. The values in these
registers are digitally added to the value of the ADC output. The
purpose of doing this is to match a benefit that is present with
manual offset adjustment. Adjusting these registers is an easy
way to make brightness adjustments. Although some signal
range is lost with this method, it has proven to be a very
popular function. In order to be able to increase and decrease
brightness, the values in these registers in this mode are signed
twos complement. The digital adder is only used in auto offset
mode. Although it cannot be disabled, setting the offset
registers to all 0s effectively disables it by always adding 0.
PIXEL CLOCK
INVALID SAMPLE TIMES
SYNC-ON-GREEN
The sync-on-green input operates in two steps. First, it sets a
baseline clamp level off of the incoming video signal with a
negative peak detector. Second, it sets the sync trigger level to a
programmable level (typically 150 mV) above the negative
peak. The sync-on-green input must be ac-coupled to the green
analog input through its own capacitor, as shown in Figure 5.
The value of the capacitor must be 1 nF 20%. If sync-on-green
is not used, this connection is not required. The sync-on-green
signal is always negative polarity.
Figure 6. Pixel Sampling Times
Any jitter in the clock reduces the precision with which the
sampling time can be determined, and must also be subtracted
from the stable pixel time.
Considerable care has been taken in the design of the
AD9985A’s clock generation circuit to minimize jitter. As shown
in Figure 7, the clock jitter of the AD9985A is less than 5% of
the total pixel time in all operating modes, making the
reduction in the valid sampling time negligible due to jitter.
Rev. 0 | Page 13 of 32
AD9985A
14
12
10
8
3-Bit Charge Pump Current Register
This register allows the current that drives the low-pass loop filter
to be varied. The possible current values are listed in Table 7.
Table 7. Charge Pump Current/Control Bits
Ip2
Ip1
Ip0
Current (μA)
0
0
0
50
0
0
1
100
6
0
1
0
150
0
1
1
250
4
1
0
0
350
2
0
1
1
1
0
1
1
1
0
1
500
750
1500
0
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
FREQUENCY (MHz)
5-Bit Phase Adjust Register
Figure 7. Pixel Clock Jitter vs. Frequency
The phase of the generated sampling clock can be shifted to
locate an optimum sampling point within a clock cycle. The
phase adjust register provides 32 phase-shift steps of 11.25°
each. The Hsync signal with an identical phase shift is available
through the HSOUT pin.
The PLL characteristics are determined by the loop filter design,
the PLL charge pump current, and the VCO range setting. The
loop filter design is shown in Figure 8. Recommended settings
of VCO range and charge pump current for VESA standard
display modes are listed in Table 9.
The COAST pin is used to allow the PLL to continue to run at
the same frequency in the absence of the incoming Hsync signal
or during disturbances in Hsync (such as equalization pulses).
This can be used during the vertical sync period, or any other
time that the Hsync signal is unavailable. The polarity of the
Coast signal is set through the Coast polarity register. Also, the
polarity of the Hsync signal is set through the Hsync polarity
register. If not using automatic polarity detection, the Hsync
and Coast polarity bits should be set to match the respective
polarities of the input signals.
PV
D
C
C
Z
0.082μF
P
0.0082μF
R
2.7kΩ
Z
FILT
Figure 8. PLL Loop Filter Detail
Four programmable registers are provided to optimize the
performance of the PLL.
12-Bit Divisor Register
POWER MANAGEMENT
The AD9985A uses the activity detect circuits, the active
interface bits in the serial bus, the active interface override bits,
and the power-down bit to determine the correct power state.
The three power states are full-power, seek mode, and power-
down. Table 8 summarizes how the AD9985A determines
which power mode to be in and which circuitry is powered
on/off in each of these modes. The power-down command has
priority over the automatic circuitry.
The input Hsync frequencies range from 15 kHz to 110 kHz.
The PLL multiplies the frequency of the Hsync signal,
producing pixel clock frequencies in the range of 12 MHz to
110 MHz. The divisor register controls the exact multiplication
factor. This register can be set to any value between 221 and
4095. (The divide ratio that is actually used is the programmed
divide ratio plus 1.)
2-Bit VCO Range Register
Table 8. Power-Down Mode Descriptions
To improve the noise performance of the AD9985A, the VCO
operating frequency range is divided into three overlapping
regions. The VCO range register sets this operating range.
Table 6 shows the frequency ranges for the lowest and highest
regions.
Inputs
Sync
Powered On or
Comments
Mode
Power-Down1
Detect2
Full-
Power
1
1
1
0
Everything
Seek
Mode
Serial Bus, Sync Activity
Detect, SOG, Band Gap
Reference
Table 6. VCO Frequency Ranges
Pixel Clock Range (MHz)
Power-
Down
0
X
Serial Bus, Sync Activity
Detect, SOG, Band Gap
Reference
PV1
PV0
AD9985AKSTZ
12 to 32
32 to 6ꢀ
6ꢀ to 110
110 to 1ꢀ0
AD9985ABSTZ
12 to 30
30 to 60
0
0
1
1
0
1
0
1
1 Power-down is controlled via Bit 1 in Serial Bus Register 0x0F.
2 Sync detect is determined by OR’ing Bits 7, ꢀ, and 1 in Serial Bus Register 0x1ꢀ.
60 to 110
Rev. 0 | Page 1ꢀ of 32
AD9985A
Table 9. Recommended VCO Range and Charge Pump Current Settings for Standard Display Formats
AD9985AKSTZ
VCORNGE Current
AD9985ABSTZ
VCORNGE Current
Standard
Modes
Refresh
Rate
Horizontal
Frequency
Resolution
Pixel Rate
PLL Div
799
835
8ꢀ1
831
VGA
6ꢀ0 × ꢀ80
60 Hz
72 Hz
75 Hz
85 Hz
56 Hz
60 Hz
72 Hz
75 Hz
85 Hz
60 Hz
70 Hz
75 Hz
80 Hz
85 Hz
31.5 kHz
37.7 kHz
37.5 kHz
ꢀ3.3 kHz
35.1 kHz
37.9 kHz
ꢀ8.1 kHz
ꢀ6.9 kHz
53.7 kHz
ꢀ8.ꢀ kHz
56.5 kHz
60.0 kHz
6ꢀ.0 kHz
68.3 kHz
6ꢀ.0 kHz
80.0 kHz
25.175 MHz
31.500 MHz
31.500 MHz
36.000 MHz
36.000 MHz
ꢀ0.000 MHz
50.000 MHz
ꢀ9.500 MHz
56.250 MHz
65.000 MHz
75.000 MHz
78.750 MHz
85.500 MHz
9ꢀ.500 MHz
108.000 MHz
135.000 MHz
00
00
00
01
01
01
01
01
01
10
10
10
10
10
10
11
110
110
110
100
100
100
101
101
101
101
100
100
101
101
110
110
00
01
01
01
01
01
01
01
01
10
10
10
10
10
10
011
010
010
010
010
011
100
100
101
011
011
011
100
100
101
SVGA
800 × 600
1025
1055
1039
1055
10ꢀ7
13ꢀ3
1327
1313
1335
1383
1687
1687
XGA
102ꢀ × 768
SXGA
1280 × 102ꢀ 60 Hz
75 Hz
TV Modes
ꢀ80i
ꢀ80p
720p
1080i
720 × ꢀ80
720 × ꢀ83
1280 × 720
60Hz
60Hz
60Hz
15.75 kHz
31.ꢀ7 kHz
ꢀ5.0 kHz
13.51MHz
27.00 MHz
7ꢀ.25 MHz
7ꢀ.25 MHz
857
857
16ꢀ9
2199
00
00
10
10
011
110
100
100
00
00
10
10
011
011
011
011
1920 × 1080 60Hz
33.75 kHz
TIMING
Hsync TIMING
The timing diagrams in this section show the operation of the
AD9985A.
Hsync is processed in the AD9985A to eliminate ambiguity in
the timing of the leading edge with respect to the phase-delayed
pixel clock and data.
The output data clock signal is created so that its rising edge
always occurs between data transitions, and can be used to latch
the output data externally.
The Hsync input is used as a reference to generate the pixel
sampling clock. The sampling phase can be adjusted, with
respect to Hsync, through a full 360° in 32 steps via the phase
adjust register (to optimize the pixel sampling time). Display
systems use Hsync to align memory and display write cycles;
therefore, it is important to have a stable timing relationship
between Hsync output (HSOUT) and data clock (DATACK).
The pipeline in the AD9985A must be flushed before valid data
becomes available. This means that four data sets are presented
before valid data is available.
tPER
tCYCLE
Three things happen to Horizontal Sync in the AD9985A. First,
the polarity of Hsync input is determined and thus has a known
output polarity. The known output polarity can be programmed
either active high or active low (Register 0x0E,
Bit 5). Second, HSOUT is aligned with DATACK and data
outputs. Third, the duration of HSOUT (in pixel clocks) is set
via Register 0x07. HSOUT is the sync signal that should be used
to drive the rest of the display system.
DATACK
tSKEW
DATA
HSOUT
Figure 9. Output Timing
Rev. 0 | Page 15 of 32
AD9985A
COAST TIMING
In most computer systems, the Hsync signal is provided
continuously on a dedicated wire. In these systems, the Coast
input and function are unnecessary and should not be used, and
the pin should be permanently connected to the inactive state.
important to ignore these distortions. If the pixel clock PLL
detects extraneous pulses, it attempts to lock to this new
frequency, and changes frequency by the end of the Vsync
period. It then takes a few lines of correct Hsync timing to
recover at the beginning of a new frame, resulting in a tearing of
the image at the top of the display.
In some systems, however, Hsync is disturbed during the
vertical sync period (Vsync). In some cases, Hsync pulses
disappear. In other systems, such as those that use composite
sync (Csync) signals or embedded sync-on-green (SOG), Hsync
includes equalization pulses or other distortions during Vsync.
To avoid upsetting the clock generator during Vsync, it is
The Coast input is provided to eliminate this problem. It is an
asynchronous input that disables the PLL input and allows the
clock to free-run at its then-current frequency. The PLL can
free-run for several lines without significant frequency drift.
P0
P1
P2
P3
P4
P5
P6
P7
RGB
IN
HSYNC
PxCK
HS
5-PIPE DELAY
ADCCK
DATACK
D
D0
D1
D2
D3
D4
D5
D6
D7
OUTA
HSOUT
VARIABLE DURATION
.
Figure 10. 4:4:4 Mode (For RGB and YUV)
P0
P1
P2
P3
P4
P5
P6
P7
RGB
IN
HSYNC
PxCK
HS
5-PIPE DELAY
ADCCK
DATACK
G
Y0
Y1
Y2
U2
Y3
V3
Y4
U4
Y5
V5
Y6
U6
Y7
V7
OUTA
R
U0
V1
OUTA
HSOUT
VARIABLE DURATION
Figure 11. 4:2:2 Mode (For YUV Only)
Rev. 0 | Page 16 of 32
AD9985A
2-WIRE SERIAL REGISTER MAP
The AD9985A is initialized and controlled by a set of registers that determine the operating modes. An external controller is used to write
and read the control registers through the two-line serial interface port.
Table 10. Control Register Map
Write and
Hexadecimal Read or
Default
Bits Value
Register
Name
Address
Read-Only
Function
0x00
RO
7:0
Chip Revision
An 8-bit register that represents the silicon revision level.
0x011
R/W
7:0
01101001 PLL Div MSB
This register is for Bits [11:ꢀ] of the PLL divider. Greater values mean
the PLL operates at a faster rate. This register should be loaded first
whenever a change is needed. This will give the PLL more time to lock.
0x021
0x03
R/W
R/W
7:ꢀ
7:3
1101****
01******
**001***
10000***
PLL Div LSB
Bits [7:ꢀ] of this word are written to the LSBs [3:0] of the PLL divider
word.
Bits [7:6] VCO Range. Selects VCO frequency range. (See the PLL
description.)
Bits [5:3] Charge Pump Current. Varies the current that drives the
low-pass filter. (See the PLL description.)
0x0ꢀ
0x05
0x06
0x07
R/W
R/W
R/W
R/W
7:3
7:0
7:0
7:0
Phase Adjust
ADC Clock Phase Adjustment. Larger values mean more delay.
(1 LSB = T/32)
10000000 Clamp
Placement
10000000 Clamp
Duration
Places the clamp signal an integer number of clock periods after the
trailing edge of the Hsync signal.
Number of clock periods that the clamp signal is actively clamping.
00100000 Hsync Output
Pulse Width
Sets the number of pixel clocks that HSOUT will remain active.
0x08
0x09
0x0A
0x0B
0x0C
0x0D
0x0E
R/W
R/W
R/W
R/W
R/W
R/W
R/W
7:0
7:0
7:0
7:1
7:1
7:1
7:0
10000000 Red Gain
10000000 Green Gain
10000000 Blue Gain
1000000* Red Offset
1000000* Green Offset
1000000* Blue Offset
Controls the ADC input range (contrast) of each respective channel.
Greater values give less contrast.
Controls dc offset (brightness) of each respective channel. Greater
values decrease brightness.
0*******
*1******
**0*****
***0****
Sync Control
Bit 7—Hsync Polarity Override. (Logic 0 = polarity determined by
chip, Logic 1 = polarity set by Bit 6 in Register 0x0E.)
Bit 6—Hsync Input Polarity. Indicates polarity of incoming Hsync
signal to the PLL. (Logic 0 = active low, Logic 1 = active high.)
Bit 5—Hsync Output Polarity. (Logic 0 = logic high sync,
Logic 1 = logic low sync.)
Bit ꢀ—Active Hsync Override. If set to Logic 1, the user can select the
Hsync to be used via Bit 3. If set to Logic 0, the active interface is
selected via Bit 6 in Register 0x1ꢀ.
****0***
Bit 3—Active Hsync Select. Logic 0 selects Hsync as the active sync.
Logic 1 selects sync-on-green as the active sync. Note that the
indicated Hsync is used only if Bit ꢀ is set to Logic 1 or if both syncs
are active. (Bits 1, 7 = Logic 1 in Register 0x1ꢀ.)
*****0**
******0*
Bit 2—Vsync Output Invert. (Logic 1 = no invert, Logic 0 = invert.)
Bit 1—Active Vsync Override. If set to Logic 1, the user can select the
Vsync to be used via Bit 0. If set to Logic 0, the active interface is
selected via Bit 3 in Register 0x1ꢀ.
*******0
0*******
Bit 0—Active Vsync Select. Logic 0 selects raw Vsync as the output
Vsync. Logic 1 selects sync separated Vsync as the output Vsync.
Note that the indicated Vsync is used only if Bit 1 is set to Logic 1.
0x0F
R/W
7:1
Bit 7—Clamp Function. Chooses between Hsync for clamp signal or
another external signal to be used for clamping. (Logic 0 = Hsync,
Logic 1 = Clamp.)
Rev. 0 | Page 17 of 32
AD9985A
Write and
Hexadecimal Read or
Default
Bits Value
Register
Name
Address
Read-Only
Function
*1******
**0*****
***0****
****1***
*****1**
******1*
Bit 6—Clamp Polarity. Valid only with external clamp signal.
(Logic 0 = active high, Logic 1 selects active low.)
Bit 5—Coast Select. Logic 0 selects the COAST input pins to be used
for the PLL coast. Logic 1 selects Vsync to be used for the PLL coast.
Bit ꢀ—Coast Polarity Override. (Logic 0 = polarity determined by
chip, Logic 1 = polarity set by Bit 3 in Register 0x0F.)
Bit 3—Coast Polarity. Selects polarity of external Coast signal
(Logic 0 = active low, Logic 1 = active high).
Bit 2—Seek Mode Override (Logic 1 = allow low power mode,
Logic 0 = disallow low power mode).
Bit 1—PWRDN. Full Chip Power-Down, Active Low (Logic 0 = full chip
power-down, Logic 1 = normal).
0x10
0x11
R/W
R/W
7:3
7:0
10111***
*****0**
******0*
*******0
Sync-on-Green Sync-on-Green Threshold. Sets the voltage level of the sync-on-
Threshold
green slicer’s comparator.
Bit 2—Red Clamp Select. Logic 0 selects clamp to ground. Logic 1
selects clamp to midscale (voltage at Pin 37).
Bit 1—Green Clamp Select. Logic 0 selects clamp to ground. Logic 1
selects clamp to midscale (voltage at Pin 37).
Bit 0— Blue Clamp Select. Logic 0 selects clamp to ground. Logic 1
selects clamp to midscale (voltage at Pin 37).
00100000 Sync Separator Sync Separator Threshold. Sets the number of internal 5 MHz clock
Threshold
periods the sync separator counts to before toggling high or low.
This should be set to some number greater than the maximum Hsync
or equalization pulse width.
0x12
0x13
0x1ꢀ
R/W
R/W
RO
7:0
7:0
7:0
00000000 Pre-Coast
00000000 Post-Coast
Sync Detect
Pre-Coast. Sets the number of Hsync periods that Coast becomes
active prior to Vsync.
Post-Coast. Sets the number of Hsync periods that Coast stays active
following Vsync.
Bit 7—Hsync detect. It is set to Logic 1 if Hsync is present on the
analog interface; otherwise it is set to Logic 0.
Bit 6—AHS: Active Hsync. This bit indicates which analog Hsync is
being used (Logic 0 = Hsync input pin, Logic 1 = Hsync from
sync-on-green).
Bit 5—Input Hsync Polarity Detect (Logic 0 = active low,
Logic 1 = active high).
Bit ꢀ—Vsync Detect. It is set to Logic 1 if Vsync is present on the
analog interface; otherwise it is set to Logic 0.
Bit 3—AVS: Active Vsync. This bit indicates which analog Vsync is
being used (Logic 0 = Vsync input pin, Logic 1 = Vsync from
sync separator).
Bit 2—Output Vsync Polarity Detect (Logic 0 = active low,
Logic 1 = active high).
Bit 1—Sync-on-Green Detect. It is set to Logic 1 if sync is present on
the green video input; otherwise it is set to 0.
Bit 0—Input Coast Polarity Detect (Logic 0 = active low,
Logic 1 = active high).
0x15
R/W
7:2
1
111111**
******1*
*******1
Reserved
Bits [7:2] Reserved for future use. Must be written to 111111 for
proper operation.
Bit 1—ꢀ:2:2 Output Formatting Mode (Logic 0 = ꢀ:2:2 mode,
Logic 1= ꢀ:ꢀ:ꢀ mode).
Output
Formats
Reserved
0
Bit 0—Must be set to 0 for proper operation.
Rev. 0 | Page 18 of 32
AD9985A
Write and
Hexadecimal Read or
Default
Bits Value
Register
Name
Address
Read-Only
Function
0x16
R/W
7
0*******
Extra PLL
Divider
Bit 7—Extra PLL Divider. (Logic 0 = off, Logic 1 = extra divide-by-2).
6:5
*00*****
SOGIN
Bandwidth
Control
Bits [6:5]—SOGIN Bandwidth Control; 00 = 300 MHz;
01 or 10 = 13 MHz; 11 = 6.5 MHz.
ꢀ
***0****
****0000
Analog Input
Bandwidth
Control
Bit ꢀ—Sets the bandwdith of the red, green and blue analog inputs.
(Logic 0 = 300 MHz, Logic 1 = 7 MHz).
3:0
7:0
7:0
7:0
Reserved
Reserved.
0x17
0x18
0x19
RO
Test Register
Test Register
Reserved.
RO
Reserved.
R/W
00000100 Red Target
Code
Target Code for Auto-Offset Operation.
0x1A
0x1B
R/W
R/W
7:0
7:0
00000100 Green Target
Code
Target Code for Auto-Offset Operation.
Target Code for Auto-Offset Operation.
00000100 Blue Target
Code
0x1C
0x1D
R/W
R/W
7:0
7
00010001 Reserved
Must be written to 0x11 for proper operation.
Enables the auto-offset circuitry.
0*******
Auto Offset
Enable
6
*0******
Hold Auto
Offset
Holds the offset output of the auto-offset at the current value.
5:2
1:0
7:0
**1001**
******10
0000****
Reserved
Update Mode
Test Register
Must be written to 9 for proper operation.
Changes the update rate of the auto-offset.
Must be set to default value.
0x1E
R/W
1 The AD9985A only updates the PLL divide ratio when the LSBs are written to (Register 0x02).
VESA has established some standard timing
specifications that assist in determining the value for
PLLDIV as a function of horizontal and vertical
display resolution and frame rate (Table 8).
2-WIRE SERIAL CONTROL REGISTER DETAIL CHIP
IDENTIFICATION
00
7–0 Chip Revision
An 8-bit register that represents the silicon revision.
However, many computer systems do not conform
precisely to the recommendations, and these numbers
should be used only as a guide. The display system
manufacturer should provide automatic or manual
means for optimizing PLLDIV. An incorrectly set
PLLDIV usually produces one or more vertical noise
bars on the display. The greater the error, the greater
the number of bars produced.
PLL DIVIDER CONTROL
01
7–0
PLL Divide Ratio MSBs
The 8 most significant bits of the 12-bit PLL divide
ratio PLLDIV. (The operational divide ratio is
PLLDIV + 1.)
The PLL derives a master clock from an incoming
Hsync signal. The master clock frequency is then
divided by an integer value, such that the output is
phase-locked to Hsync. This PLLDIV value
determines the number of pixel times (pixels plus
horizontal blanking overhead) per line. This is
typically 20% to 30% more than the number of active
pixels in the display.
The power-up default value of PLLDIV is 1693
(PLLDIVM = 0x69, PLLDIVL = 0xDx).
The AD9985A updates the full-divide ratio only when
the LSBs are changed. Writing to the MSB by itself
does not trigger an update.
02
7–4 PLL Divide Ratio LSBs
The 12-bit value of the PLL divider supports divide
ratios from 2 to 4095. The higher the value loaded in
this register, the higher the resulting clock frequency
with respect to a fixed Hsync frequency.
The 4 least significant bits of the 12-bit PLL divide
ratio PLLDIV. The operational divide ratio is
PLLDIV + 1.
Rev. 0 | Page 19 of 32
AD9985A
The power-up default value of PLLDIV is 1693
CLAMP TIMING
(PLLDIVM = 0x69, PLLDIVL = 0xDx). The
AD9985A updates the full divide ratio only when this
register is written to.
05
7–0 Clamp Placement
An 8-bit register that sets the position of the internally
generated clamp.
CLOCK GENERATOR CONTROL
When clamp function (Register 0x0F, Bit 7) = 0, a
clamp signal is generated internally, at a position
established by the clamp placement and for a duration
set by the clamp duration. Clamping is started (clamp
placement) pixel periods after the trailing edge of
Hsync. The clamp placement can be programmed to
any value between 1 and 255.
03
7–6 VCO Range Select
Two bits that establish the operating range of the clock
generator.
VCORNGE must be set to correspond with the
desired operating frequency (incoming pixel rate).
The PLL gives the best jitter performance at high
frequencies. For this reason, to output low pixel rates
and still get good jitter performance, the PLL actually
operates at a higher frequency but then divides down
the clock rate afterwards. Table 11 shows the pixel
rates for each VCO range setting. The PLL output
divisor is automatically selected with the VCO range
setting.
The clamp should be placed during a time that the
input signal presents a stable black-level reference,
usually the back porch period between Hsync and the
image.
When clamp function = 1, this register is ignored.
06
7–0 Clamp Duration
An 8-bit register that sets the duration of the
internally generated clamp.
Table 11. VCO Ranges
Pixel Clock Range (MHz)
For the best results, the clamp duration should be set
to include the majority of the black reference signal
time that follows the Hsync signal trailing edge.
Insufficient clamping time can produce brightness
changes at the top of the screen, and a slow recovery
from large changes in the average picture level (APL),
or brightness.
PV1 PV0 AD9985AKSTZ
AD9985ABSTZ
0
0
0
1
12 to 32
32 to 6ꢀ (power-up
default)
12 to 30
30 to 60 (power-up
default)
1
1
0
1
6ꢀ to 110
110 to 1ꢀ0
60 to 110
03
5–3 Current Charge Pump Current
Three bits that establish the current driving the loop
filter in the clock generator.
When clamp function = 1, this register is ignored.
HSYNC PULSE WIDTH
Current must be set to correspond with the desired
operating frequency (incoming pixel rate).
07
7–0 Hsync Output Pulse Width
An 8-bit register that sets the duration of the Hsync
output pulse.
Table 12. Charge Pump Currents
CURRENT
Current (μA)
The leading edge of the Hsync output is triggered by
the internally generated, phase-adjusted PLL feedback
clock. The AD9985A then counts a number of pixel
clocks equal to the value in this register. This triggers
the trailing edge of the Hsync output, which is also
phase adjusted.
000
001
010
011
100
101
110
111
50
100 (power-up default)
150
250
350
500
750
1500
INPUT GAIN
08
7–0 Red Channel Gain Adjust (REDGAIN)
An 8-bit word that sets the gain of the red channel.
The AD9985A can accommodate input signals with a
full-scale range of between 0.5 V and 1.0 V p-p.
Setting REDGAIN to 255 corresponds to a 1.0 V input
range. A REDGAIN of 0 establishes a 0.5 V input
range. Increasing REDGAIN results in the picture
having less contrast (the input signal uses fewer of the
available converter codes). See Figure 4.
04
7–3 Clock Phase Adjust
A 5-bit value that adjusts the sampling phase in 32
steps across one pixel time. Each step represents an
11.25° shift in sampling phase.
The power-up default value is 16.
Rev. 0 | Page 20 of 32
AD9985A
09
7–0 Green Channel Gain Adjust (GREENGAIN)
An 8-bit word that sets the gain of the green channel.
See REDGAIN (08).
MODE CONTROL 1
0E
7
Hsync Input Polarity Override
This register is used to override the internal circuitry
that determines the polarity of the Hsync signal going
into the PLL.
0A
7–0 Blue Channel Gain Adjust (BLUEGAIN)
An 8-bit word that sets the gain of the blue channel.
See REDGAIN (08).
Table 13. Hsync Input Polarity Override Settings
Override
Result
INPUT OFFSET
0
1
Hsync polarity determined by chip
Hsync polarity determined by user
0B
7–1 Red Channel Offset Adjust
This offset register and those that follow have two
modes of operation. One mode is when the auto offset
function is turned off (manual mode) and the other is
when auto offset is turned on.
The default for Hsync polarity override is 0 (polarity
determined by chip).
0E
6
HSPOL Hsync Input Polarity
A bit that must be set to indicate the polarity of the
Hsync signal that is applied to the PLL Hsync input.
When in manual offset adjustment mode (auto offset
turned off), this register behaves exactly like the
AD9883A. It is a 7-bit offset binary word that sets the
dc offset of the red channel. One LSB of offset
Table 14. Hsync Input Polarity Settings
Polarity
Result
adjustment equals approximately one LSB change in
the ADC offset. Therefore, the absolute magnitude of
the offset adjustment scales as the gain of the channel
is changed. A nominal setting of 63 results in the
channel nominally clamping the back porch (during
the clamping interval) to Code 00. An offset setting of
127 results in the channel clamping to Code 64 of the
ADC. An offset setting of 0 clamps to Code –63 (off
the bottom of the range). Increasing the value of red
offset decreases the brightness of the channel.
0
1
Active low
Active high (power-up default)
Active low means the leading edge of the Hsync pulse
is negative-going. All timing is based on the leading
edge of Hsync, which is the falling edge. The rising
edge has no effect.
Active high is inverted from the traditional Hsync,
with a positive-going pulse. This means that timing is
based on the leading edge of Hsync, which is now the
rising edge.
When in auto offset mode, the value in this register is
digitally added to the red channel ADC output. The
purpose of doing this is to match the operation with
manual offset adjustment. Adjusting these registers is
an easy way to make brightness adjustments.
Although some signal range is lost with this method, it
has proven to be a very popular function. In order to
be able to increase and decrease brightness, the values
in these registers in this mode are signed twos comple-
ment (vs. manual mode, where the values in this
register are binary). The digital adder is used only in
auto offset mode. Although it cannot be disabled,
setting this register to all 0s effectively disables it by
always adding 0.
The device operates if this bit is set incorrectly, but the
internally generated clamp position, as established by
clamp placement (Register 0x05), is not placed as
expected, which can generate clamping errors.
0E
5
Hsync Output Polarity
This bit determines the polarity of the Hsync output
and the SOG output. Table 15 shows the effect of this
option. SYNC indicates the logic state of the sync
pulse.
Table 15. Hsync Output Polarity Settings
Polarity
Result
0
1
Logic 1 (positive polarity; power-up default)
Logic 0 (negative polarity)
0C
0D
7–1 Green Channel Offset Adjust
This register works exactly like the Red Channel
Offset Adjust Register (0x0B), except it is for the green
channel.
0E
4
Active Hsync Override
This bit is used to override the automatic Hsync
selection. To override, set this bit to Logic 1. When
overriding, the active Hsync is set via Bit 3 in this
register.
7–1 Blue Channel Offset Adjust
This register works exactly like the Red Channel
Offset Adjust register (0x0B), except it is for the blue
channel.
Rev. 0 | Page 21 of 32
AD9985A
Table 16. Active Hsync Override Settings
Table 21. Clamp Input Signal Source Settings
Override Result
Clamp Function
Result
0
Autodetermines the active interface (power-up
default)
0
Internally generated clamp signal (power-
up default)
1
Override, Bit 3 determines the active interface
1
Externally provided clamp signal
0E
3
Active Hsync Select
A 0 enables the clamp timing circuitry controlled by
clamp placement and clamp duration. The clamp
position and duration is counted from the leading
edge of Hsync.
This bit is used under two conditions. It is used to
select the active Hsync when the override bit is set
(Bit 4). Alternately, it is used to determine the active
Hsync when not overriding, but both Hsyncs are
detected.
A 1 enables the external CLAMP input pin. The three
channels are clamped when the clamp signal is active.
The polarity of clamp is determined by the clamp
polarity bit (Register 0x0F, Bit 6).
Table 17. Active Hsync Select Settings
Select
0
1
Result
Hsync input (power-up default)
Sync-on-green input
0F
6
Clamp Input Signal Polarity
This bit determines the polarity of the externally
provided clamp signal.
0E
2
Vsync Output Invert
This bit inverts the polarity of the Vsync output
Table 18 shows the effect of this option.
Table 22. Clamp Input Signal Polarity Settings
Clamp Function
Result
Table 18. Vsync Output Invert Settings
Invert
1
0
Active low (power-up default)
Active high
Vsync Output
0
1
Invert (power-up default)
No invert
Logic 1 means that the circuit clamps when CLAMP is
low, and it passes the signal to the ADC when CLAMP
is high.
0E
1
Active Vsync Override
This bit is used to override the automatic Vsync
selection. To override, set this bit to Logic 1. When
overriding, the active interface is set via Bit 0 in this
register.
Logic 0 means that the circuit clamps when CLAMP is
high, and it passes the signal to the ADC when
CLAMP is low.
Table 19. Active Vsync Override Settings
Override Result
0F
5
Coast Select
This bit is used to select the active Coast source. The
choices are the COAST input pin or Vsync. If Vsync is
selected, the additional decision to use the Vsync
input pin or the output from the sync separator needs
to be made (Register 0x0E, Bits 1, 0).
0
1
Autodetermines the active Vsync (power-up default)
Override, Bit 0 determines the active Vsync
0E
0
Active Vsync Select
This bit is used to select the active Vsync when the
override bit is set (Bit 1).
Table 23. Power-Down Settings
Table 20. Active Vsync Select Settings
Power-Down
Result
Select
Result
0
1
COAST input pin
Vsync (See the Coast Select section)
0
1
Vsync input (power-up default)
Sync separator output
0F
4
Coast Input Polarity Override
0F
7
Clamp Input Signal Source
This register is used to override the internal circuitry
that determines the polarity of the Coast signal going
into the PLL.
This bit determines the source of clamp timing.
Rev. 0 | Page 22 of 32
AD9985A
Table 24. Coast Input Polarity Override Settings
10
2
Red Clamp Select
This bit determines whether the red channel is
clamped to ground or to midscale. For RGB video, all
three channels are referenced to ground. For YCbCr
(or YUV), the Y channel is referenced to ground, but
the CbCr channels are referenced to midscale.
Clamping to midscale actually clamps to Pin 37.
Override
Result
0
1
Determined by chip (power-up default)
Determined by user
0F
3
Coast Input Polarity
This bit indicates the polarity of the Coast signal that
is applied to the PLL COAST input.
Table 28. Red Clamp Select Settings
Table 25. Coast Input Polarity Settings
Coast Polarity Result
Clamp
Result
0
1
Clamp to ground (power-up default)
Clamp to midscale (Pin 37)
0
1
Active low
Active high (power-up default)
10
1
Green Clamp Select
Active low means that the clock generator ignores
Hsync inputs when Coast is low, and continues
operating at the same nominal frequency until Coast
goes high.
This bit determines whether the green channel is
clamped to ground or to midscale.
Table 29. Green Clamp Select Settings
Clamp
Result
Active High means that the clock generator ignores
Hsync inputs when Coast is high, and continues
operating at the same nominal frequency until Coast
goes low.
0
1
Clamp to ground (power-up default)
Clamp to midscale (Pin 37)
10
0
Blue Clamp Select
This bit determines whether the blue channel is
clamped to ground or to midscale.
This function needs to be used along with the Coast
polarity override bit (Bit 4).
Table 30. Blue Clamp Select Settings
0F
2
Seek Mode Override
Clamp
Result
This bit is used to either allow or disallow the low
power mode. The low power mode (seek mode)
occurs when there are no signals on any of the Sync
inputs.
0
1
Clamp to ground (power-up default)
Clamp to midscale (Pin 37)
11
7–0
Sync Separator Threshold
This register is used to set the responsiveness of the
sync separator. It sets the number of internal 5 MHz
clock periods the sync separator must count to before
toggling high or low. It works like a low-pass filter to
ignore Hsync pulses in order to extract the Vsync
signal. This register should be set to some number
greater than the maximum Hsync pulse width. The
sync separator threshold uses an internal dedicated
clock with a frequency of approximately 5 MHz.
Table 26. Seek Mode Override Settings
Override
Result
1
0
Allow seek mode (power-up default)
Disallow seek mode
0F
1
PWRDN
This bit is used to put the chip in full power-down. See
the Power Management section for details on which
blocks are powered down.
The default for this register is 32.
Table 27. Power-Down Settings
Power-Down Result
12
13
7–0 Pre-Coast
This register allows the Coast signal to be applied
prior to the Vsync signal. This is necessary in cases
where pre-equalization pulses are present. The step
size for this control is one Hsync period.
0
1
Power-down
Normal operation
10
7-3
Sync-on-Green Slicer Threshold
This register allows the comparator threshold of the
sync-on-green slicer to be adjusted. This register
adjusts it in steps of 10 mV, with the minimum setting
equaling 10 mV (11111) and the maximum setting
equaling 330 mV (00000).
The default is 0.
7–0 Post-Coast
This register allows the Coast signal to be applied
following the Vsync signal. This is necessary when
post-equalization pulses are present. The step size for
this control is one Hsync period.
The default setting is 23, which corresponds to a
threshold value of 100 mV; for a threshold of 150 mV,
the setting should be 18.
The default is 0.
Rev. 0 | Page 23 of 32
AD9985A
14
7
Hsync Detect
Table 34. Vsync Detection Results
This bit is used to indicate when activity is detected on
the Hsync input pin (Pin 30). If Hsync is held high or
low, activity will not be detected.
Detect
Result
0
1
No activity detected
Activity detected
Table 31. Hsync Detection Results
The sync processing block diagram (Figure 14) shows
where this function is implemented.
Detect
Function
0
1
No activity detected
Activity detected
14
3
Active Vsync (AVS)
This bit indicates which Vsync source is being used,
the Vsync input or output from the sync separator.
Bit 4 in this register determines which is active. If both
Vsync and SOG are detected, the user can determine
which has priority via Bit 0 in Register 0x0E. The user
can override this function via Bit 1 in Register 0x0E. If
the override bit is set to Logic 1, this bit is set to the
state of Bit 0 in Register 0x0E.
The sync processing block diagram (Figure 14) shows
where this function is implemented.
14
6
Active Hsync (AHS)
This bit indicates which Hsync input source is being
used by the PLL (Hsync input or sync-on-green).
Bit 7 and Bit 1 in this register determine which source
is used. If both Hsync and SOG are detected, the user
can determine which has priority via Bit 3 in
Register 0x0E. The user can override this function via
Bit 4 in Register 0x0E. If the override bit is set to
Logic 1, then this bit is set to the state of Bit 3 in
Register 0x0E.
Table 35. Active Vsync Results
Bit 4, Reg 14H
(Vsync Detect)
Bit 1, Reg. 0x 0E
(Override)
AVS
1
0
X
0
0
1
0
1
Bit 0 in 0x0E
Table 32. Active Hsync Results
Bit 7
(Hsync
Detect)
AVS = 0 means Vsync input.
AVS = 1 means Sync separator.
Bit 1
(SOG
Bit 4
Reg. 0x0E
Detect)
(Override)
AHS
The override bit is in Register 0x0E, Bit 1.
0
0
1
1
X
0
1
0
1
X
0
0
0
0
1
Bit 3 in 0x0E
1
0
Bit 3 in 0x0E
Bit 3 in 0x0E
14
2 Detected Vsync Output Polarity Status
This bit reports the status of the Vsync output polarity
detection circuit. It can be used to determine the
polarity of the Vsync output. The detection circuit’s
location is shown in the sync processing block
diagram (Figure 14).
AHS = 0 means use the Hsync pin input for Hsync.
AHS = 1 means use the SOG pin input for Hsync.
The override bit is in Register 0x0E, Bit 4.
Table 36. Detected Vsync Output Polarity Status
Vsync Polarity
Status
Result
0
1
Active low
Active high
14
5
Detected Hsync Input Polarity Status
This bit reports the status of the Hsync input polarity
detection circuit. It can be used to determine the
polarity of the Hsync input. The detection circuit’s
location is shown in the sync processing block
diagram (Figure 14).
14
1
Sync-on-Green Detect
This bit is used to indicate when sync activity is
detected on the sync-on-green input pin (Pin 49).
Table 37. Sync-on-Green Detection Results
Table 33. Detected Hsync Input Polarity Status
Detect
Result
Hsync Polarity Status
Result
0
1
No activity detected
Activity detected
0
1
Negative
Positive
The sync processing block diagram (Figure 14) shows
where this function is implemented.
14
4
Vsync Detect
14
0
Detected Coast Polarity Status
This bit is used to indicate when activity is detected on
the Vsync input pin (Pin 31). If Vsync is held steady
high or low, activity is not detected.
This bit reports the status of the Coast input polarity
detection circuit. It can be used to determine the
polarity of the Coast input. The detection circuit’s
location is shown in the sync processing block
diagram (Figure 14).
Rev. 0 | Page 2ꢀ of 32
AD9985A
Table 38. Detected Coast Input Polarity Status
16
4
Analog Input Bandwidth
Polarity Status
Result
This bit controls the bandwidth of the red, green,
and blue analog inputs. In most applications, the
analog input bandwidth should be set to its maximum
(300 MHz). When there is excessive noise on the
analog inputs, reducing the bandwidth can help
suppress the noise.
0
1
Coast polarity negative
Coast polarity positive
This indicates that Bit 1 of Register 5 is the 4:2:2
output mode select bit.
15
1
4:2:2 Output Mode Select
Table 43. Anti-Aliasing Filter
A bit that configures the output data in 4:2:2 mode.
This mode can be used to reduce the number of data
lines used from 24 down to 16 for applications using
YUV, YCbCr, or YPbPr graphics signals. A timing
diagram for this mode is shown in Figure 11.
Select
Input Bandwidth
0
1
300 MHz
7 MHz
19
7:0
Red Target Code
Recommended input and output configurations are
shown in Table 39 and Table 40.
This specifies the targeted value of the final offset
for the red channel when auto-offset is used
(Register 0x1D, Bit 7 = 1). Default is 4.
Table 39. 4:2:2 Output Mode Select
Select
Output Mode
1A
1B
7:0
Green Target Code
0
1
ꢀ:2:2
ꢀ:ꢀ:ꢀ
This specifies the targeted value of the final offset
for the green channel when auto-offset is used
(Register 0x1D Bit 7 = 1). Default is 4.
Table 40. 4:2:2 Input/Output Configuration
Channel
Input Connection
Output Format
7:0
Blue Target Code
Red
Green
Blue
V
Y
U
U/V
Y
This specifies the targeted value of the final offset
for the blue channel when auto-offset is used
(Register 0x1D, Bit 7 = 1). Default is 4.
High impedance
16
7
Extra PLL Divider
1D
1D
7
Auto-Offset Enable
Enables the auto-offset circuitry. Default is 0.
Hold Auto-Offset
A bit that can add an additional divide-by-2 into the
PLL divide ratio. Enabling this function at pixel
frequencies below 20 MHz can result in improved PLL
jitter performance, as it allows the VCO to run at a
higher frequency, resulting in lower jitter.
6
Holds the offset output of the auto-offset at the
current value. Default is 0.
Table 41. PLL VCO Divide
Select
PLL Divider
0
1
Off
1D
1:0
Update Mode
Extra divide-by-2
Changes the update rate of the auto-offset.
Default is 10.
16
6-5
SOGIN Bandwidth
Two bits that can control the bandwidth of the sync-
on-green input (SOGIN). In most applications, the
SOGIN bandwidth should be set to its maximum
(300 MHz). When there is excessive noise on SOGIN,
reducing the bandwidth can help suppress the noise.
Table 44. Auto-Offset Update Rate
Update Mode
Auto-Offset Update Timing
00
01
10
Every clamp cycle
Every 16 clamp cycles
Every 6ꢀ camp cycles
Table 42. SOGIN Bandwidth
Select
Pulses Filtered
00
01 or 10
11
300 MHz
13 MHz
6.5 MHz
Rev. 0 | Page 25 of 32
AD9985A
2-WIRE SERIAL CONTROL PORT
A 2-wire serial interface control interface is provided. Two
AD9985A devices can be connected to the 2-wire serial
interface; each device has a unique address.
DATA TRANSFER VIA SERIAL INTERFACE
For each byte of data read or written, the MSB is the first bit of
the sequence.
The 2-wire serial interface comprises a clock (SCL) and a
bidirectional data (SDA) pin. The analog flat panel interface
acts as a slave for receiving and transmitting data over the serial
interface. When the serial interface is not active, the logic levels
on SCL and SDA are pulled high by external pull-up resistors.
If the AD9985A does not acknowledge the master device during
a write sequence, the SDA remains high so the master can
generate a stop signal. If the master device does not acknowl-
edge the AD9985A during a read sequence, the AD9985A
interprets this as end-of-data. The SDA remains high so the
master can generate a stop signal.
Data received or transmitted on the SDA line must be stable for
the duration of the positive-going SCL pulse. Data on SDA must
change only when SCL is low. If SDA changes state while SCL is
high, the serial interface interprets that action as a start or stop
sequence.
Writing data to specific control registers of the AD9985A
requires that the 8-bit address of the control register of interest
be written after the slave address has been established. This
control register address is the base address for subsequent write
operations. The base address auto-increments by one for each
byte of data written after the data byte intended for the base
address.
The components to serial bus operation are
•
•
•
•
•
Start signal
Slave address byte
Base register address byte
Data byte to read or write
Stop signal
Data is read from the control registers of the AD9985A in a
similar manner. Reading requires two data transfer operations:
The base address must be written with the R/W bit of the slave
address byte low to set up a sequential read operation.
When the serial interface is inactive (SCL and SDA are high),
communications are initiated by sending a start signal. The start
signal is a high-to-low transition on SDA while SCL is high.
This signal alerts all slave devices that a data transfer sequence
is coming.
Reading (the R/ bit of the slave address byte high) begins at
W
the previously established base address. The address of the read
register auto-increments after each byte is transferred.
The first eight bits of data transferred after a start signal com-
To terminate a read/write sequence to the AD9985A, a stop
signal must be sent. A stop signal comprises a low-to-high
transition of SDA while SCL is high.
prise a 7-bit slave address (the first seven bits) and a single R/
W
bit (the eighth bit). The R/ bit indicates the direction of data
W
transfer, read from (1) or write to (0) the slave device. If the
transmitted slave address matches the address of the device (set
by the state of the SA1-0 input pins in Table 45), the AD9985A
acknowledges by bringing SDA low on the ninth SCL pulse. If
the addresses do not match, the AD9985A does not acknowledge.
A repeated start signal occurs when the master device driving
the serial interface generates a start signal without first generat-
ing a stop signal to terminate the current communication. This
is used to change the mode of communication (read, write)
between the slave and master without releasing the serial
interface lines.
Table 45. Serial Port Addresses
Bit 7
A6
Bit 6
A5
Bit 5
A4
Bit 4
A3
Bit 3
A2
Bit 2
A1
Bit 1
A0
(MSB)
1
1
0
0
0
0
1
1
1
1
0
0
0
1
SDA
tBUFF
tSTAH
tDSU
tDHO
tSTOSU
tSTASU
tDAL
SCL
tDAH
Figure 12. Serial Port Read/Write Timing
Rev. 0 | Page 26 of 32
AD9985A
Serial Interface Read/Write Examples
Write to one control register:
1. Start signal
Read from one control register:
1. Start signal
2. Slave address byte (R/ bit = low)
W
3. Base address byte
4. Start signal
2. Slave address byte (R/ Bit = low)
W
3. Base address byte
4. Data byte to base address
5. Stop signal
5. Slave address byte (R/ bit = high)
W
6. Data byte from base address
7. Stop signal
Write to four consecutive control registers:
1. Start signal
Read from four consecutive control registers:
1. Start signal
2. Slave address byte (R/ bit = low)
W
2. Slave address byte (R/ bit = low)
W
3. Base address byte
3. Base address byte
4. Start signal
4. Data byte to base address
5. Data byte to (base address + 1)
6. Data byte to (base address + 2)
7. Data byte to (base address + 3)
8. Stop signal
5. Slave address byte (R/ Bit = high)
W
6. Data byte from base address
7. Data byte from (base address + 1)
8. Data byte from (base Address + 2)
9. Data byte from (base Address + 3)
10. Stop signal
SDA
SCL
BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
ACK
BIT 7
Figure 13. Serial Interface—Typical Byte Transfer
ACTIVITY
DETECT
SYNC STRIPPER
SYNC SEPARATOR
INTEGRATOR
NEGATIVE PEAK
CLAMP
COMP
SYNC
VSYNC
1/S
SOG
MUX 1
HSYNC IN
SOG OUT
PLL
ACTIVITY
DETECT
POLARITY
DETECT
HSYNC OUT
PIXEL CLOCK
HSYNC
HSYNC OUT
CLOCK
GENERATOR
MUX 2
MUX 3
COAST
COAST
POLARITY
DETECT
AD9985A
VSYNC IN
VSYNC OUT
ACTIVITY
DETECT
POLARITY
DETECT
MUX 4
Figure 14. Sync Processing Block Diagram
Rev. 0 | Page 27 of 32
AD9985A
Table 46. Control of the Sync Block Muxes via the Serial Register
Mux No.
Serial Bus Control Bit
Control Bit State
Result
1 and 2
0x0E: Bit 3
0
1
0
1
0
1
Pass Hsync
Pass sync-on-green
Pass Coast
Pass Vsync
Pass Vsync
3
ꢀ
0x0F: Bit 5
0x0E: Bit 0
Pass sync separator signal
SYNC SLICER
The purpose of the sync slicer is to extract the sync signal from
the green graphics channel. A sync signal is not present on all
graphics systems, only those with sync-on-green. The sync
signal is extracted from the green channel in a two-step process.
First, the SOG input is clamped to its negative peak (typically,
0.3 V below the black level). Next, the signal goes to a compara-
tor with a variable trigger level, nominally 0.15 V above the
clamped level. The sliced sync is typically a composite sync
signal containing both Hsync and Vsync.
The specific value of N varies for different video modes, but is
always less than 255. For example, with a 1 μs width Hsync, the
counter only reaches 5 (1 μs/200 ns = 5). Now, when Vsync is
present on the composite sync, the counter also counts up.
However, since the Vsync signal is much longer, it counts to a
higher number M. For most video modes, M is at least 255. So,
Vsync can be detected on the composite sync signal by
detecting when the counter counts to a value higher than N.
The specific count that triggers detection (T) can be
programmed through the serial register (0x11).
SYNC SEPARATOR
Once Vsync has been detected, there is a similar process to
detect when it goes inactive. At detection, the counter first
resets to 0, then starts counting up when Vsync goes away.
Similar to the previous case, it detects the absence of Vsync
when the counter reaches the threshold count (T). In this way, it
rejects noise and/or serration pulses. Once Vsync is detected to
be absent, the counter resets to 0 and begins the cycle again.
A sync separator extracts the Vsync signal from a composite
sync signal. It does this through a low-pass filter-like or
integrator-like operation. It works on the idea that the Vsync
signal stays active for a much longer time than the Hsync signal,
so it rejects any signal shorter than a threshold value, which is
somewhere between an Hsync pulse width and a Vsync pulse
width.
The sync separator on the AD9985A is simply an 8-bit digital
counter with a 5 MHz clock. It works independently of the
polarity of the composite sync signal. (Polarities are determined
elsewhere on the chip.) The basic idea is that the counter counts
up when Hsync pulses are present. But since Hsync pulses are
relatively short in width, the counter only reaches a value of N
before the pulse ends. It then starts counting down, eventually
reaching 0 before the next Hsync pulse arrives.
Rev. 0 | Page 28 of 32
AD9985A
The bypass capacitors should be physically located between the
power plane and the power pin. Current should flow from the
power plane to the capacitor to the power pin. Do not make the
power connection between the capacitor and the power pin.
Placing a via underneath the capacitor pads, down to the power
plane, is generally the best approach.
PCB LAYOUT RECOMMENDATIONS
The AD9985A is a high precision, high speed analog device.
Consequently, to get the maximum performance out of the part,
it is important to have a board with a good layout. This section
provides guidelines for designing a board using the AD9985A.
It is particularly important to maintain low noise and good
stability of PVD (the clock generator supply). Abrupt changes in
PVD can result in similarly abrupt changes in sampling clock
phase and frequency. This can be avoided by careful attention to
regulation, filtering, and bypassing. It is highly desirable to
provide separate regulated supplies for each of the analog
circuitry groups (VD and PVD).
ANALOG INTERFACE INPUTS
Using the following layout techniques on the graphics inputs is
extremely important.
Minimize the trace length running into the graphics inputs.
This is accomplished by placing the AD9985A as close as
possible to the graphics VGA connector. Long input trace
lengths are undesirable because they pick up more noise from
the board and other external sources.
Some graphic controllers use substantially different levels of
power when active (during active picture time) and when idle
(during horizontal and vertical sync periods). This can result in
a measurable change in the voltage supplied to the analog
supply regulator, which can, in turn, produce changes in the
regulated analog supply voltage. This can be mitigated by
regulating the analog supply, or at least PVD, from a different,
cleaner power source (for example, from a 12 V supply).
Place the 75 Ω termination resistors (see Figure 1) as close as
possible to the AD9985A chip. Any additional trace length
between the termination resistors and the input of the
AD9985A increases the magnitude of reflections, which
corrupts the graphics signal.
Use 75 Ω matched impedance traces. Trace impedances other
than 75 Ω also increase the chance of reflections.
It is recommended to use a single ground plane for the entire
board. Experience has repeatedly shown that the noise
performance is the same or better with a single ground plane.
Using multiple ground planes can be detrimental because each
separate ground plane is smaller, and long ground loops can
result.
The AD9985A has very high input bandwidth (500 MHz).
While this is desirable for acquiring a high resolution PC
graphics signal with fast edges, it means that it also captures any
high frequency noise present. Therefore, it is important to
reduce the amount of noise that is coupled to the inputs. Avoid
running any digital traces near the analog inputs.
When using separate ground planes is unavoidable, it is
recommended to minimally place a single ground plane under
the AD9985A. The location of the split should be at the receiver
of the digital outputs. For this case, it is even more important to
place components wisely because the current loops are much
longer (current takes the path of least resistance). Figure 15
shows an example of a current loop.
Due to the high bandwidth of the AD9985A, low-pass filtering
the analog inputs can sometimes help to reduce noise. (For
many applications, filtering is unnecessary.) Experiments
have shown that placing a series ferrite bead prior to the 75 Ω
termination resistor is helpful in filtering out excess noise.
Specifically, the part used was the #2508051217Z0 from Fair-
Rite, but each application can work best with a different bead
value. Alternately, placing a 100 Ω to 120 Ω resistor between the
75 Ω termination resistor and the input coupling capacitor can
also be beneficial.
P
L
O
A
C
POWER SUPPLY BYPASSING
It is recommended to bypass each power supply pin with a
0.1 μF capacitor. The exception is when two or more supply
pins are adjacent to each other. For these groupings of powers/
grounds, it is necessary to have only one bypass capacitor. The
fundamental idea is to have a bypass capacitor within about
0.5 cm of each power pin. Also, avoid placing the capacitor on
the opposite side of the PC board from the AD9985A, as that
interposes resistive vias in the path.
E
A
D
I
D G
Figure 15. Current Loop
PLL
Place the PLL loop filter components as close to the FILT pin as
possible.
Do not place any digital or other high frequency traces near
these components.
Use the values suggested in the data sheet with 10% tolerances
or less.
Rev. 0 | Page 29 of 32
AD9985A
OUTPUTS (BOTH DATA AND CLOCKS)
DIGITAL INPUTS
Try to minimize the trace length that the digital outputs have to
drive. Longer traces have higher capacitance, which requires
more current, which causes more internal digital noise. Shorter
traces reduce the possibility of reflections.
The digital inputs on the AD9985A were designed to work with
3.3 V signals, but are tolerant of 5.0 V signals. Therefore, no
extra components need to be added if using 5.0 V logic.
Any noise that gets onto the Hsync input trace adds jitter to the
system. Therefore, minimize the trace length and do not run
any digital or other high frequency traces near it.
Adding a series resistor of value 22 Ω to 100 Ω can suppress
reflections, reduce EMI, and reduce the current spikes inside of
the AD9985A. However, if 50 Ω traces are used on the PCB, the
data outputs should not need resistors. A 22 Ω resistor on the
DATACK output should provide good impedance matching
that reduces reflections. If series resistors are used, place them
as close as possible to the AD9985A pins (but try not to add vias
or extra length to the output trace in order to get the resistors
closer).
VOLTAGE REFERENCE
Bypass the voltage reference with a 0.1 μF capacitor. Place it as
close as possible to the AD9985A pin. Make the ground
connection as short as possible.
If possible, limit the capacitance that each of the digital outputs
drives to less than 10 pF. This can easily be accomplished by
keeping traces short and by connecting the outputs to only one
device. Loading the outputs with excessive capacitance increases
the current transients inside of the AD9985A, creating more
digital noise on its power supplies.
Rev. 0 | Page 30 of 32
AD9985A
OUTLINE DIMENSIONS
16.20
16.00 SQ
15.80
0.75
0.60
0.45
1.60
MAX
80
61
60
1
PIN 1
14.20
14.00 SQ
13.80
TOP VIEW
(PINS DOWN)
1.45
1.40
1.35
0.20
0.09
7°
3.5°
0°
0.10 MAX
COPLANARITY
20
41
0.15
0.05
40
21
SEATING
PLANE
VIEW A
0.65
0.38
0.32
0.22
BSC
LEAD PITCH
VIEW A
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026-BEC
Figure 16. 80-Lead Low Profile Quad Flat Package [LQFP]
(ST-80-2)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD9985ABSTZ-1101
AD9985AKSTZ-1101
AD9985AKSTZ-1ꢀ01
AD9985A/PCB
Temperature Range
–ꢀ0°C to +85°C
0°C to 70°C
Package Description
80-lead LQFP
80-lead LQFP
80-lead LQFP
Evaluation Board
Package Option
ST-80-2
ST-80-2
0°C to 70°C
ST-80-2
1 Z = Pb-free part.
Rev. 0 | Page 31 of 32
AD9985A
NOTES
©
2005 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05484-0-7/05(0)
Rev. 0 | Page 32 of 32
相关型号：
©2020 ICPDF网 联系我们和版权申明