ADA4870-KGD-DF [ADI]
High Speed, High Voltage, 1 A Output Drive Amplifier;型号: | ADA4870-KGD-DF |
厂家: | ADI |
描述: | High Speed, High Voltage, 1 A Output Drive Amplifier 放大器 |
文件: | 总8页 (文件大小:218K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
High Speed, High Voltage,
1 A Output Drive Amplifier
Known Good Die
ADA4870-KGD
FUNCTIONAL BLOCK DIAGRAM
FEATURES
Ideal for driving high capacitive or low resistive loads
Wide supply range: 10 V to 40 V
High output current drive: 1 A
Wide output voltage swing: 37 V swing with 40 V supply
High slew rate: 2500 V/µs
OUT
OUT
OUT
OUT
INP
INN
OUT
High bandwidth: 52 MHz large signal, 70 MHz small signal
Low noise: 2.1 nV/√Hz
Quiescent current: 32.5 mA
ADA4870-KGD
Figure 1.
Power down: 0.75 mA
Short-circuit protection and flag
Current limit: 1.2 A
Thermal protection
APPLICATIONS
Envelope tracking
Power FET driver
Ultrasound
Piezo drivers
PIN diode drivers
Waveform generation
Automated test equipment (ATE)
CCD panel drivers
Composite amplifiers
GENERAL DESCRIPTION
The ADA4870-KGDis a unity-gain stable, high speed current
feedbackamplifier capable of delivering 1 A of output current
and 2500 V/µs slew rate from a 40 V supply. Manufactured
using the Analog Devices, Inc., proprietary high voltage extra
fast complementary bipolar (XFCB)process, the innovative
architecture of the ADA4870-KGD enables high output power,
high speed signalprocessing solutions in applications that
require driving a low impedance load.
The ADA4870-KGDis available in a 26-pad bare die. The
ADA4870-KGD operatesoverthe industrial temperature range
(−40°C to +85°C).
Additional application and technical information can be found
in the ADA4870 data sheet.
Known Good Die (KGD): these die are fully guaranteed to data
sheet specifications.
The ADA4870-KGDis ideal for driving high voltage power
FETs, piezo transducers, PIN diodes, CCD panels, anda variety
of other demanding applications that requirehigh speed from
high supply voltage at high output current.
Rev. 0
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Technical Support
©2014 Analog Devices, Inc. All rights reserved.
www.analog.com
ADA4870-KGD
Known Good Die
TABLE OF CONTENTS
Features........................................................................................... 1
Absolute Maximum Ratings......................................................... 6
ESD Cautio n............................................................................... 6
Pin Configuration and Function Descriptions............................ 7
Outline Dimensions...................................................................... 8
Die Specifications and Assembly Recommendations ............. 8
Ordering Guide.......................................................................... 8
Applications................................................................................... 1
Functional Block Diagram............................................................ 1
General Description...................................................................... 1
Revision History............................................................................ 2
Specifications................................................................................. 3
20 V Supply.............................................................................. 3
5 V Supply................................................................................ 4
REVISION HISTORY
10/14—Revision0: Initial Version
Rev. 0 | Page 2 of 8
Known Good Die
ADA4870-KGD
SPECIFICATIONS
20 V SUPPLY
TCASE = 25°C, AV = −5, RF = 1.21 kΩ, RG = 243 Ω, CL = 300 pF, RS = 5 Ω, unless otherwise noted.
Table 1.
Parameter
Test Conditions/Comments
Min
Typ
Max
Unit
DYNAMIC PERFORMANCE
−3 dB Bandwidth
VOUT = 2 V p-p
60
MHz
MHz
MHz
V/µs
ns
VOUT = 2 V p-p, AV = +2
VOUT = 20 V p-p
VOUT = 30 V step, AV = +2
VOUT = 10 V step
70
52
2500
82
Slew Rate (Peak)
Settling Time to 0.1%
NOISE/DISTORTION PERFORMANCE
Harmonic Distortion, HD2/HD3
f = 30 MHz, VOUT = 20 V p-p, AV = −10
f = 1 MHz, VOUT = 20 V p-p, AV = −10
f = 0.1 MHz, VOUT = 20 V p-p, AV = −10
f = 1 MHz, VOUT = 20 V p-p, RL = 25 Ω, AV = −10
f = 0.1 MHz, VOUT = 20 V p-p, RL = 25 Ω, AV = −10
f = 100 kHz
−40/−39
−91/−74
−95/−96
−70/−77
−79/−99
2.1
dBc
dBc
dBc
dBc
dBc
Input Voltage Noise Density
Input Current Noise Density
INP
nV/√Hz
f = 100 kHz
4.2
47
pA/√Hz
pA/√Hz
INN
DC PERFORMANCE
Input Offset Voltage
Input Offset Voltage Drift
Input Bias Current
−15
−1
4
+10
mV
µV/°C
Noninverting Input
9
23
µA
Inverting Input
−12
24
2.5
−25
µA
Input Bias Current Drift, Inverting Input
Open-Loop Transresistance
INPUT CHARACTERISTICS
Input Resistance
nA/°C
MΩ
INP
INP
2
MΩ
pF
V
Input Capacitance
0.75
18
60
Input Common-ModeVoltage Range(VICM
Common-Mode Rejection Ratio
)
VICM
=
2 V, 18 V
58
dB
PIN (SHUTDOWN)
SD
Input Voltages
High (enabled)
Low (power-down)
VEE + 1.1
VEE
VEE + 5
VEE + 0.9
V
V
Enabled ( = VEE + 5 V)
SD
Input Bias Current
110
−50
µA
µA
Power down
= VEE)
SD
PIN (RESET AND SHORT-CIRCUIT
ON
PROTECTION)
Input Voltages
High (power-down)
Low (enabled)
VEE + 1.8
VEE
VEE + 5
VEE + 1.3
V
V
Enabled (
ON
Power down (
ON
= VEE)
Input Bias Current
−75
100
µA
= VEE + 5 V)
µA
OUTPUT CHARACTERISTICS
Output Voltage Range
RG = 1.2 kΩ, RL = open
RG = 1.2 kΩ, RL = 50 Ω
18.6
18
V
V
A
A
Output Current Drive
Short-Circuit Protection Current Limit
1
= floating
ON
1.2
Rev. 0 | Page 3 of 8
ADA4870-KGD
Known Good Die
Parameter
Test Conditions/Comments
Min
Typ
Max
Unit
POWER SUPPLY
Operating Range
Quiescent Current
10
40
33
1
V
= VEE + 5 V,
= VEE
32.5
0.75
mA
mA
SD
SD
SD
ON
= not applicable
= VEE,
ON
= VEE + 5 V,
= VEE + 5 V
5.1
69
64
5.8
mA
dB
dB
ON
Positive Power Supply Rejection Ratio
Negative Power Supply Rejection Ratio
67
62
5 V SUPPLY
TCASE = 25°C, AV = −5, RF = 1.21 kΩ, RG = 243 Ω, CL = 300 pF, RS = 5 Ω, unless otherwise noted.
Table 2.
Parameter
Test Conditions/Comments
Min
Typ
Max
Unit
DYNAMIC PERFORMANCE
−3 dB Bandwidth
Settling Time to 0.1%
VOUT = 2 V p-p
VOUT = 2 V step
52
55
MHz
ns
NOISE/DISTORTION PERFORMANCE
Harmonic Distortion, HD2/HD3
f = 30 MHz, VOUT = 2 V p-p, AV = −10
f = 1 MHz, VOUT = 2 V p-p, AV = −10
f = 0.1 MHz, VOUT = 2 V p-p, AV = −10
f = 1 MHz, VOUT = 2 V p-p, RL = 25 Ω, AV = −10
f = 0.1 MHz, VOUT = 2 Vp-p, RL = 25 Ω, AV = −10
f = 100 kHz
−42/−38
−90/−88
−101/−107
−70/−66
−85/−86
2.1
dBc
dBc
dBc
dBc
dBc
nV/√Hz
Input Voltage Noise Density
Input Current Noise Density
INP
f = 100 kHz
4.2
47
pA/√Hz
pA/√Hz
INN
DC PERFORMANCE
Input Offset Voltage
−15
−4
14
+5
mV
Input Offset Voltage Drift
Input Bias Current
µV/°C
Noninverting Input
Inverting Input
Input Bias Current Drift, Inverting Input
Open-Loop Transresistance
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Common-Mode Voltage Range (VICM
Common-Mode Rejection Ratio
13
−5
10
1.9
23
−18
µA
µA
nA/°C
MΩ
INP
INP
2
MΩ
pF
V
0.75
3.0
59
)
VICM
=
0.5 V, 3.0 V
57
dB
PIN (SHUTDOWN)
SD
Input Voltages
High (enabled)
Low (power-down)
VEE + 1.1
VEE
VEE + 5
VEE + 0.9
V
V
Enabled ( = VEE + 5 V)
SD
Power down ( = VEE)
SD
Input Bias Current
110
−65
µA
µA
PIN (RESET AND SHORT-CIRCUIT
ON
PROTECTION)
Input Voltages
High (power-down)
Low (enabled)
VEE + 1.8
VEE
VEE + 5
V
VEE + 1.3
V
Enabled (
ON
Power down (
ON
= VEE)
Input Bias Current
−75
100
µA
= VEE + 5 V)
µA
Rev. 0 | Page 4 of 8
Known Good Die
ADA4870-KGD
Parameter
Test Conditions/Comments
Min
Typ
Max
Unit
OUTPUT CHARACTERISTICS
Output Voltage Range
Output Current Drive
RG = 1.2 kΩ, RL = open
3.7
1
1.2
V
A
A
= floating
ON
Short-Circuit Protection Current Limit
POWER SUPPLY
Operating Range
Quiescent Current
10
40
30
V
mA
= VEE + 5 V,
= VEE
28
SD
SD
SD
ON
= not applicable
= VEE,
ON
= VEE + 5 V,
0.65
1
mA
= VEE + 5 V
4.7
68
63
5.5
mA
dB
dB
ON
Positive Power Supply Rejection Ratio
Negative Power Supply Rejection Ratio
66
61
Rev. 0 | Page 5 of 8
ADA4870-KGD
Known Good Die
ABSOLUTEMAXIMUM RATINGS
Stresses at or abovethoselisted under AbsoluteMaximum
Ratings may cause permanent damageto the product. This is a
stress rating only; functionaloperation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditionsfor extended periods may
affect product reliability.
Table 3.
Parameter
Rating
Supply Voltage
42 V
Common-Mode InputVoltage Range
Differential Input Voltage Range
Storage Temperature Range
Operating Temperature Range
Lead Temperature (Soldering, 10 sec)
Junction Temperature
VEE to VCC
0.7 V
−65°C to +150°C
−40°C to +85°C
300°C
150°C
ESD CAUTION
Rev. 0 | Page 6 of 8
Known Good Die
ADA4870-KGD
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
2
1
20
3
4
17B
17A
16B
16A
15B
15A
14B
14A
19A
18B
18A
19B
6
7
8
12A
12B
13A
13B
10 11
Figure 2. Pad Configuration
Table 4. Pad Function Descriptions
Pad No.
X-Axis (μm)
Y-Axis (μm)
Mnemonic
Description
Positive Power Supply Input
1
18.525
747.075
VCC
2
−1235.175
−1286.125
−1286.525
Not applicable
−1288.625
−1290.275
−1290.275
Not applicable
−168.475
−64.175
+751.875
+624.875
+532.175
Not applicable
−65.725
−272.175
−364.875
Not applicable
−732.375
−732.325
−316.075
−316.075
−316.025
−316.025
−272.125
−177.225
−82.975
11.225
106.675
210.875
314.225
418.425
338.375
336.725
336.725
TFL
SD
Thermal Monitor and Short-Circuit Flag (Referenced to VEE)
Shutdown (Active Low, Referenced to VEE)
Turn On/Enable (Active Low, Referenced to VEE)
Not applicable
Noninverting Input
Inverting Input
3
ON
4
5
6
7
8
9
10
11
12A
12B
13A
13B
14A
14B
15A
15B
16A
16B
17A
17B
18A
18B
19A
19B
20
Not applicable
INP
INN
OUT
Not applicable
VEE
VEE
VEE
VEE
VEE
Output
Not applicable
Negative Power Supply Input
Negative Power Supply Input
Negative Power Supply Input
Negative Power Supply Input
Negative Power Supply Input
Negative Power Supply Input
Output
Output
Output
Output
Output
Output
Output
Output
Positive Power Supply Input
Positive Power Supply Input
Positive Power Supply Input
Positive Power Supply Input
Positive Power Supply Input
+46.125
+139.025
+1037.875
+1140.175
+1311.275
+1311.275
+1311.275
1311.275
1311.275
1311.275
1311.275
1311.275
861.925
VEE
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
VCC
VCC
636.425
543.725
320.675
119.125
VCC
VCC
VCC
337.225
747.075
Rev. 0 | Page 7 of 8
ADA4870-KGD
Known Good Die
OUTLINEDIMENSIONS
0.000254
2.965
1.825
TOP VIEW
(CIRCUIT SIDE)
SIDE VIEW
0.072 × 0.072
Figure 3. 26-Pad Bare Die [CHIP]
(C-26-1)
Dimensions shown in millimeters
DIE SPECIFICATIONS ANDASSEMBLY RECOMMENDATIONS
Table 5. Die Specifications
Parameter
Value
Unit
µm
Scribe Line Width
75
Die Size
2965 (x) × 1825 (y)
10
µm
Thickness
mils
Backside
Ti 1000 Å, Ni 3000 Å, Au 1000 Å (Au outermost) Not applicable
Passivation
5 µm Polyimide on top of 1 µm Oxynitride
Not applicable
Bond Pads (Minimum)
Bond Pad Composition
ESD
72 × 72
µm
%
AlCu (0.5%)
Human Body Model (HBM)
Field-Induced Charged Device Model (FICDM)
4
1.25
kV
kV
Table 6. Assembly Recommendations
Assembly Component
Recommendation
Die Attach
Cookson D591-3B sintered Ag conductive
1.0 mils minimum
Unspecified
Minimum Bond Line Thickness
Bonding Sequence
ORDERING GUIDE
Model
Temperature Range
−40°C to +85°C
−40°C to +85°C
Package Description
Package Option
C-26-1
C-26-1
ADA4870-KGD-DF
ADA4870-KGD-WP
26-Pad Bare Die [CHIP]
26-Pad Bare Die [CHIP]
©2014 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D12203-0-10/14(0)
Rev. 0 | Page 8 of 8
相关型号:
©2020 ICPDF网 联系我们和版权申明