ADE7816 [ADI]
Six Current Channels, One Voltage Channel; 六电流通道，一电压通道
| 型号： | ADE7816 |
| 厂家： | 
ADI |
| 描述： | Six Current Channels, One Voltage Channel |
| 文件： | 总48页 (文件大小：655K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Six Current Channels, One Voltage Channel
Energy Metering IC
Data Sheet
ADE7816
voltage and current. The device incorporates seven sigma-delta
(Σ-Δ) ADCs with a high accuracy energy measurement core.
FEATURES
Measures active and reactive energy, sampled waveforms,
and current and voltage rms
6 current input channels and 1 voltage channel
<0.1% error in active and reactive energy over a dynamic
range of 1000:1
Supports current transformer and Rogowski coil sensors
Provides instantaneous current and voltage readings
Angle measurements on all 6 channels
2 kHz bandwidth operation
The six current input channels allow multiple loads to be measured
simultaneously. The voltage channel and the six current channels
each have a complete signal path allowing for a full range of
measurements. Each input channel supports a flexible gain stage
and is suitable for use with current transformers (CTs). Six on-
chip digital integrators facilitate the use of the Rogowski coil
sensors.
The ADE7816 provides access to on-chip meter registers via either
the SPI or I2C interface. A dedicated high speed interface, the
high speed data capture (HSDC) port, can be used in conjunction
with I2C to provide access to real-time ADC output information.
A full range of power quality information, such as overcurrent,
overvoltage, peak, and sag detection, is accessible via the two
Reference: 1.2 V (drift 10 ppm/°C typical) with external
overdrive capability
Flexible I2C, SPI, and HSDC serial interfaces
GENERAL DESCRIPTION
The ADE7816 is a highly accurate, multichannel metering
device that is capable of measuring one voltage channel and up
to six current channels. It measures line voltage and current and
calculates active and reactive energy, as well as instantaneous rms
IRQ0
IRQ1
external interrupt pins,
and
.
The ADE7816 energy metering IC operates from a 3.3 V supply
voltage and is available in a 40-lead LFCSP that is Pb free and
RoHS compliant.
FUNCTIONAL BLOCK DIAGRAM
REF
RESET
4
IN/OUT
17
DGND
6
27
28
CLKIN
2
3
PULL_HIGH
PULL_LOW
VRMSOS
1.2V
REF
ADE7816
CLKOUT
VGAIN
2
VRMS
X
LPF
15
16
VP
VN
ADC
PGA2
PGA1
HPF
HPF
AWATTOS
AWGAIN
IAGAIN
DIGITAL
INTEGRATOR
29
32
36
IRQ0
PCF_A_COEFF
2
SPI/I C
LPF
IRQ1
7
8
IAP
IAN
ENERGY
AND RMS
DATA
ADC
AVAROS AVARGAIN
SCLK/SCL
ALL
COMPUTATIONAL
BLOCK FOR
CHANNELS
38 MOSI/SDA
37 MISO/HSD
9
TOTAL
IBP
REACTIVE POWER
PGA1
PGA1
ADC
ADC
ADC
ADC
ADC
ENERGY AND RMS CALCULATIONS SEE
CHANNEL A FOR DETAILED SIGNAL PATH
2
I C
IBN 12
IARMSOS
ICP 13
ICN 14
39 SS/HSA
35 HSCLK
HSDC
ENERGY AND RMS CALCULATIONS SEE
CHANNEL A FOR DETAILED SIGNAL PATH
2
IARMS
X
LPF
23
22
19
IDP
IEP
IFP
PGA3
PGA3
PGA3
ENERGY AND RMS CALCULATIONS SEE
CHANNEL A FOR DETAILED SIGNAL PATH
1
NC
10 NC
11 NC
20 NC
21 NC
30 NC
ENERGY AND RMS CALCULATIONS SEE
CHANNEL A FOR DETAILED SIGNAL PATH
POR
26
LDO
LDO
ENERGY AND RMS CALCULATIONS SEE
CHANNEL A FOR DETAILED SIGNAL PATH
IN 18
25
24
5
40
NC
34
33
31
VDD AGND
AVDD
DVDD
NC
NC
NC
Figure 1.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2012 Analog Devices, Inc. All rights reserved.
ADE7816
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Energy Gain Calibration ........................................................... 24
Energy Offset Calibration ......................................................... 24
Energy Phase Calibration.......................................................... 25
RMS Offset Calibration............................................................. 25
Power Quality Features.................................................................. 26
Selecting a Current Channel Group ........................................ 26
Instantaneous Waveforms......................................................... 26
Zero-Crossing Detection........................................................... 26
Peak Detection............................................................................ 27
Overcurrent and Overvoltage Detection ................................ 27
Indication of Power Direction.................................................. 28
Angle Measurements ................................................................. 28
Period Measurement.................................................................. 29
Voltage Sag Detection................................................................ 29
Setting the SAGCYC Register................................................... 29
Setting the SAGLVL Register.................................................... 29
Voltage Sag Interrupt ................................................................. 29
Checksum.................................................................................... 30
Outputs ............................................................................................ 31
Interrupts..................................................................................... 31
Communication ......................................................................... 31
Registers........................................................................................... 36
Register Protection..................................................................... 36
Register Format .......................................................................... 36
Register Maps.............................................................................. 37
Outline Dimensions....................................................................... 45
Ordering Guide .......................................................................... 45
General Description......................................................................... 1
Functional Block Diagram .............................................................. 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Timing Characteristics ................................................................ 5
Absolute Maximum Ratings............................................................ 8
Thermal Resistance ...................................................................... 8
ESD Caution.................................................................................. 8
Pin Configuration and Function Descriptions............................. 9
Typical Performance Characteristics ........................................... 11
Test Circuit ...................................................................................... 14
Quick Start....................................................................................... 16
Inputs................................................................................................ 17
Power and Ground ..................................................................... 17
Reference Circuit........................................................................ 17
Reset ............................................................................................. 17
CLKIN and CLKOUT................................................................ 18
Analog Inputs.............................................................................. 18
Energy Measurements.................................................................... 20
Starting and Stopping the DSP ................................................. 20
Active Energy Measurement..................................................... 20
Reactive Energy Measurement ................................................. 21
Line Cycle Accumulation Mode............................................... 22
Root Mean Square Measurement............................................. 23
No Load Detection..................................................................... 23
Energy Calibration ......................................................................... 24
Channel Matching...................................................................... 24
REVISION HISTORY
2/12—Revision 0: Initial Version
Rev. 0 | Page 2 of 48
Data Sheet
ADE7816
SPECIFICATIONS
VDD = 3.3 V 10ꢀ, AGND = DGND = 0 V, on-chip reference, CLKIN = 16.384 MHz, TMIN to TMAX = −40°C to +85°C.
Table 1.
Parameter 1, 2
Min
Typ
Max
Unit
Test Conditions/Comments
ACCURACY
Active Energy Measurement
Active Energy Measurement Error
(per Channel)
0.1
0.2
0.1
%
%
%
Over a dynamic range of 1000 to 1, PGA = 1, 2, 4;
integrator off
Over a dynamic range of 3000 to 1, PGA = 1, 2, 4;
integrator off
Over a dynamic range of 500 to 1, PGA = 8,16;
integrator on
Phase Error Between Channels
Power Factor (PF) = 0.8 Capacitive
PF = 0.5 Inductive
Line frequency = 45 Hz to 65 Hz, HPF on
Phase lead = 37°
Phase lag = 60°
0.05
0.05
Degrees
Degrees
AC Power Supply Rejection
VDD = 3.3 V + 120 mV rms/120 Hz, IxP = VP =
100 mV rms
Energy Register Variation
DC Power Supply Rejection
0.01
%
VDD = 3.3 V 330 mV dc
Energy Register Variation
Total Active Energy Measurement Bandwidth
REACTIVE ENERGY MEASUREMENT
0.01
2
%
kHz
Reactive Energy Measurement Error
(per Channel)
0.1
0.2
0.1
%
%
%
Over a dynamic range of 1000 to 1, PGA = 1, 2, 4;
integrator off
Over a dynamic range of 3000 to 1, PGA = 1, 2, 4;
integrator off
Over a dynamic range of 500 to 1, PGA = 8,16;
integrator on
Phase Error Between Channels
PF = 0.8 Capacitive
PF = 0.5 Inductive
Line frequency = 45 Hz to 65 Hz, HPF on
Phase lead = 37°
Phase lag = 60°
0.05
0.05
Degrees
Degrees
AC Power Supply Rejection
VDD = 3.3 V + 120 mV rms/120 Hz, IxP = VP =
100 mV rms
Energy Register Variation
DC Power Supply Rejection
0.01
%
VDD = 3.3 V 330 mV dc
Energy Register Variation
Total Reactive Energy Measurement Bandwidth
RMS MEASUREMENTS
0.01
2
%
kHz
IRMS and VRMS Measurement Bandwidth
IRMS and VRMS Measurement Error
2
0.1
kHz
%
Over a dynamic range of 500 to 1; one second
of averaging (100 samples)
ANALOG INPUTS
Maximum Signal Levels
500
mV peak Single-ended inputs between the following
pins: IAP and IAN, IBP and IBN, ICP and ICN,
IDP and IN, IEP and IN, IFP and IN.
Input Impedance (DC)
IAP, IAN, IBP, IBN, ICP, ICN, IDP, IEP, and IFP Pins 400
kΩ
kΩ
IN Pin
130
ADC Offset Error
2
4
mV
PGA = 1, uncalibrated error, see the Terminology
section
External 1.2 V reference
Gain Error
%
Rev. 0 | Page 3 of 48
ADE7816
Data Sheet
Parameter 1, 2
Min
Typ
Max
Unit
Test Conditions/Comments
WAVEFORM SAMPLING
Current and Voltage Channels
Signal-to-Noise Ratio, SNR
Signal-to-Noise-and-Distortion Ratio, SINAD
Bandwidth (−3 dB)
Sampling CLKIN/2048, 16.384 MHz/2048 = 8 kSPS
See the Instantaneous Waveforms section
PGA = 1
PGA = 1
70
60
2
dB
dB
kHz
TIME INTERVAL BETWEEN CHANNELS
Measurement Error
0.3
Degrees
Line frequency = 45 Hz to 65 Hz, HPF on
Minimum = 1.2 V − 8%; maximum = 1.2 V + 8%
Nominal 1.207 V at the REFIN/OUT pin at TA = 25°C
REFERENCE INPUT
REFIN/OUT Input Voltage Range
Input Capacitance
1.1
1.2
1.3
10
V
pF
ON-CHIP REFERENCE
Reference Error
Output Impedance
2
mV
kΩ
Temperature Coefficient
10
50
ppm/°C
Maximum value across full temperature range
of −40°C to +85°C
CLKIN, CLKOUT
All specifications are for CLKIN, CLKOUT of
16.384 MHz
Input Clock Frequency
Crystal Equivalent Series Resistance
CLKIN Input Capacitance
16.22
30
16.384 16.55
MHz
Ω
pF
200
20
20
CLKOUT Output Capacitance
pF
LOGIC INPUTS—MOSI/SDA, SCLK/SCL,
SS/HSA, RESET, PULL_HIGH, PULL_LOW
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
2.0
V
V
μA
ꢀA
nA
pF
VDD = 3.3 V 10%
VDD = 3.3 V 10%
Input = 0 V, VDD = 3.3 V
Input = VDD = 3.3 V
Input = VDD = 3.3 V
0.8
−8.7
3
100
Input Capacitance, CIN
10
LOGIC OUTPUTS—IRQ0, IRQ1, MISO/HSD
VDD = 3.3 V 10%
VDD = 3.3 V 10%
Output High Voltage, VOH
ISOURCE
Output Low Voltage, VOL
ISINK
POWER SUPPLY
VDD Pin
IDD
2.4
3.0
V
μA
V
800
0.4
2
VDD = 3.3 V 10%
mA
For specified performance
Minimum = 3.3 V − 10%; maximum = 3.3 V + 10%
3.6
27.8
V
mA
25
1 See the Typical Performance Characteristics section.
2 See the Terminology section for a definition of the parameters.
Rev. 0 | Page 4 of 48
Data Sheet
ADE7816
TIMING CHARACTERISTICS
VDD = 3.3 V 10ꢀ, AGND = DGND = 0 V, on-chip reference, CLKIN = 16.384 MHz, TMIN to TMAX = −40°C to +85°C. Note that, within
the timing tables and diagrams, the dual function pin names are referenced by the relevant function only; see the Pin Configuration and
Function Descriptions section for full pin mnemonics and function descriptions.
I2C-Compatible Interface Timing
Table 2. I2C-Compatible Interface Timing Parameters
Standard Mode
Fast Mode
Parameter
Symbol
fSCL
tHD;STA
tLOW
tHIGH
tSU;STA
tHD;DAT
tSU;DAT
tR
Min
Max
Min
Max
Unit
kHz
ꢀs
μs
μs
μs
μs
ns
ns
ns
μs
μs
ns
SCL Clock Frequency
Hold Time (Repeated) Start Condition
Low Period of SCL Clock
High Period of SCL Clock
Setup Time for Repeated Start Condition
Data Hold Time
0
100
0
400
4.0
4.7
4.0
4.7
0
0.6
1.3
0.6
0.6
0
100
20
20
0.6
1.3
3.45
0.9
Data Setup Time
250
Rise Time of Both SDA and SCL Signals
Fall Time of Both SDA and SCL Signals
Setup Time for Stop Condition
Bus Free Time Between a Stop and Start Condition
Pulse Width of Suppressed Spikes
1000
300
300
300
tF
tSU;STO
tBUF
4.0
4.7
N/A1
tSP
50
1 N/A means not applicable.
SDA
tBUF
tSU;DAT
tR
tHD;STA
tF
tSP
tR
tR
tLOW
SCL
tHD;STA
tSU;STO
tHD;DAT
tSU;STA
tHIGH
START
CONDITION
REPEATED START
CONDITION
STOP
START
CONDITION CONDITION
Figure 2. I2C-Compatible Interface Timing
Rev. 0 | Page 5 of 48
ADE7816
Data Sheet
SPI Interface Timing
Table 3. SPI Interface Timing Parameters
Parameter
Symbol
Min
50
Max
Unit
ns
ꢀs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
SS to SCLK Edge
tSS
SCLK Period
SCLK Low Pulse Width
0.4
175
175
40001
tSL
tSH
SCLK High Pulse Width
Data Output Valid After SCLK Edge
Data Input Setup Time Before SCLK Edge
Data Input Hold Time After SCLK Edge
Data Output Fall Time
Data Output Rise Time
SCLK Rise Time
SCLK Fall Time
MISO Disable After SS Rising Edge
SS High After SCLK Edge
tDAV
tDSU
tDHD
tDF
tDR
tSR
tSF
tDIS
tSFS
100
100
5
20
20
20
20
200
0
1 Guaranteed by design.
SS
tSS
tSFS
SCLK
tSL
tSH
tSF
tSR
tDAV
tDIS
MSB
INTERMEDIATE BITS
LSB
MISO
tDF
tDR
INTERMEDIATE BITS
MSB IN
LSB IN
MOSI
tDSU
tDHD
Figure 3. SPI Interface Timing
Rev. 0 | Page 6 of 48
Data Sheet
ADE7816
HSDC Interface Timing
Table 4. HSDC Interface Timing Parameter
Parameter
Symbol
Min
0
125
50
Max
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
HSA to HSCLK Edge
HSCLK Period
tSS
HSCLK Low Pulse Width
HSCLK High Pulse Width
Data Output Valid After HSCLK Edge
Data Output Fall Time
Data Output Rise Time
HSCLK Rise Time
HSCLK Fall Time
HSD Disable After HSA Rising Edge
HSA High After HSCLK Edge
tSL
tSH
tDAV
tDF
tDR
tSR
tSF
tDIS
tSFS
50
40
20
20
10
10
5
0
HSA
tSS
tSFS
HSCLK
tSL
tSH
tSF
tSR
tDAV
tDIS
MSB
INTERMEDIATE BITS
tDF
LSB
HSD
tDR
Figure 4. HSDC Interface Timing
Load Circuit for All Timing Specifications
2mA
I
OL
TO OUTPUT
PIN
1.6V
C
L
50pF
800µA
I
OH
Figure 5. Load Circuit for All Timing Specifications
Rev. 0 | Page 7 of 48
ADE7816
Data Sheet
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Regarding the temperature profile used in soldering RoHS-
Table 5.
Parameter
VDD to AGND
VDD to DGND
Analog Input Voltage to AGND, IAP, IAN,
IBP, IBN, ICP, ICN, IDP, IEP, IFP, IN
Analog Input Voltage to VP and VN
Reference Input Voltage to AGND
Digital Input Voltage to DGND
Digital Output Voltage to DGND
Operating Temperature
compliant parts, Analog Devices, Inc., advises that reflow profiles
should conform to J-STD-20 from JEDEC. Refer to the JEDEC
website for the latest revision.
Rating
−0.3 V to +3.7 V
−0.3 V to +3.7 V
−2 V to +2 V
THERMAL RESISTANCE
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
−2 V to +2 V
−0.3 V to VDD + 0.3 V
−0.3 V to VDD + 0.3 V
−0.3 V to VDD + 0.3 V
Table 6. Thermal Resistance
Package Type
θJA
θJC
Unit
40-Lead LFCSP
29.3
1.8
°C/W
Industrial Range
Storage Temperature Range
Junction Temperature
−40°C to +85°C
−65°C to +150°C
150°C
ESD CAUTION
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. 0 | Page 8 of 48
Data Sheet
ADE7816
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
NC
PULL_HIGH
PULL_LOW
RESET
DVDD
1
2
3
4
5
6
7
8
9
30
29
28
NC
IRQ0
CLKOUT
27 CLKIN
26 VDD
25 AGND
ADE7816
TOP VIEW
DGND
(Not to Scale)
IAP
AVDD
IDP
24
23
IAN
IBP
22 IEP
NC
21
NC 10
NOTES
1. NC = NO CONNECT. THESE PINS ARE NOT CONNECTED
INTERNALLY AND SHOULD BE LEFT FLOATING.
2. CREATE A SIMILAR PAD ON THE PCB UNDER THE
EXPOSED PAD. SOLDER THE EXPOSED PAD TO
THE PAD ON THE PCB TO CONFER MECHANICAL
STRENGTH TO THE PACKAGE. DO NOT CONNECT
THE PADS TO AGND.
Figure 6. Pin Configuration
Table 7. Pin Function Descriptions
Pin No.
Mnemonic Description
1, 10, 11, 20,
21, 30, 31,
33, 34, 40
NC
No Connect. These pins are not connected internally and should be left floating.
2
3
4
5
PULL_HIGH
PULL_LOW
RESET
Connect this pin to VDD for proper operation.
Connect this pin to AGND for proper operation.
Active Low Reset Input. Hold this pin low for at least 10 μs to trigger a hardware reset.
DVDD
On-Chip 2.5 V Digital LDO Access. Do not connect any external active circuitry to this pin. Decouple this pin
with a 4.7 μF capacitor in parallel with a ceramic 220 nF capacitor.
6
DGND
Ground Reference. This pin provides the ground reference for the digital circuitry.
7, 8
IAP, IAN
Analog Inputs for Current Channel A. This channel is used with the current transducers and is referenced in
this data sheet as Current Channel A. Connect these inputs in a single-ended configuration with a maximum
signal level of 0.5 V with respect to IAN.
9, 12
13, 14
15, 16
17
IBP, IBN
ICP, ICN
VP, VN
Analog Inputs for Current Channel B. This channel is used with the current transducers and is referenced in
this data sheet as Current Channel B. Connect these inputs in a single-ended configuration with a maximum
signal level of 0.5 V with respect to IBN.
Analog Inputs for Current Channel C. This channel is used with the current transducers and is referenced in
this data sheet as Current Channel C. Connect these inputs in a single-ended configuration with a maximum
signal level of 0.5 V with respect to ICN.
Analog Inputs for the Voltage Channel. This channel is used with the voltage transducer and is referenced as
the voltage channel in this data sheet. Connect these inputs in a single-ended configuration with a maximum
signal level of 0.5 V with respect to VN. This channel also has an internal PGA.
On-Chip Voltage Reference Access. The on-chip reference has a nominal value of 1.2 V. An external reference
source with 1.2 V 8% can also be connected at this pin. In either case, decouple this pin to AGND with a
4.7 μF capacitor in parallel with a ceramic 100 nF capacitor.
REFIN/OUT
18
19
IN
Analog Input Common Pin for Current Channel D, Current Channel E, and Current Channel F. See the pin
descriptions for Pin 19, Pin 22, and Pin 23 for more details.
Analog Input for Current Channel F. This channel is used with the current transducers and is referenced in this
data sheet as Current Channel F. Connect this input in a single-ended configuration with a maximum signal
level of 0.5 V with respect to IN.
IFP
22
23
IEP
Analog Input for Current Channel E. This channel is used with the current transducers and is referenced in
this data sheet as Current Channel E. Connect this input in a single-ended configuration with a maximum
signal level of 0.5 V with respect to IN.
Analog Input for Current Channel D. This channel is used with the current transducers and is referenced in
this data sheet as Current Channel D. Connect this input in a single-ended configuration with a maximum
signal level of 0.5 V with respect to IN.
IDP
Rev. 0 | Page 9 of 48
ADE7816
Data Sheet
Pin No.
Mnemonic Description
24
AVDD
On-Chip 2.5 V Analog Low Dropout (LDO) Regulator Access. Do not connect external active circuitry to this
pin. Decouple this pin with a 4.7 μF capacitor in parallel with a ceramic 220 nF capacitor.
25
AGND
Ground Reference. This pin provides the ground reference for the analog circuitry. Tie this pin to the analog
ground plane or to the quietest ground reference in the system. Use this quiet ground reference for all
analog circuitry, such as antialiasing filters and current and voltage transducers.
26
27
VDD
Supply Voltage. This pin provides the supply voltage and should be set at 3.3 V 10% for specified operation.
Decouple this pin to AGND with a 10 μF capacitor in parallel with a ceramic 100 nF capacitor.
Master Clock. An external clock can be provided at this logic input. Alternatively, a parallel resonant AT-cut
crystal can be connected across CLKIN and CLKOUT to provide a clock source for the ADE7816. The clock
frequency for specified operation is 16.384 MHz. Use ceramic load capacitors of a few tens of picofarads (pF)
with the gate oscillator circuit. Refer to the crystal manufacturer data sheet for load capacitance requirements.
CLKIN
28
CLKOUT
A crystal can be connected across this pin and CLKIN (as stated in the description for Pin 27) to provide
a clock source for the ADE7816. The CLKOUT pin can drive one CMOS load when either an external clock
is supplied at CLKIN or a crystal is being used.
29, 32
IRQ0, IRQ1
Interrupt Request Outputs. These are active low logic outputs. See the Communication section for a detailed
presentation of the events that can trigger interrupts.
35
36
HSCLK
SCLK/SCL
Serial Clock Output for the HSDC Port.
Serial Clock Input for the SPI Port/Serial Clock Input for the I2C Port. All serial data transfers are synchronized to
this clock (see the Serial Interfaces section). This pin has a Schmidt trigger input for use with a clock source
that has a slow edge transition time (for example, opto-isolator outputs).
37
38
39
EP
MISO/HSD
MOSI/SDA
SS/HSA
Data Output for SPI Port/Data Output for HSDC Port.
Data Input for SPI Port/Data Output for I2C Port.
Slave Select for SPI Port/HSDC Port Active.
Exposed
Pad
Exposed Pad. Create a similar pad on the PCB under the exposed pad. Solder the exposed pad to the pad on
the PCB to confer mechanical strength to the package. Do not connect the pads to AGND.
Rev. 0 | Page 10 of 48
Data Sheet
ADE7816
TYPICAL PERFORMANCE CHARACTERISTICS
1.0
0.5
0.4
+85°C
PF = +0.5
PF = +1
PF = –0.5
+25°C
0.8
–40°C
0.3
0.6
0.4
0.2
0.1
0.2
0
0
–0.1
–0.2
–0.3
–0.4
–0.5
–0.2
–0.4
–0.6
–0.8
–1.0
45
50
55
60
65
0.01
0.1
1
10
100
FREQUENCY (Hz)
CURRENT CHANNEL (% of Full Scale)
Figure 10. Active Energy Error as a Percentage of Reading (Gain = 1,
Temperature = 25°C) over Frequency and Power Factor with
Internal Reference, Integrator Off
Figure 7. Active Energy Error as a Percentage of Reading (Gain = 1,
Power Factor = 1) over Temperature with Internal Reference,
Integrator Off
1.0
1.0
+85°C
+25°C
–40°C
PF = +0.5
PF = +1
PF = –0.5
0.8
0.8
0.6
0.4
0.6
0.4
0.2
0.2
0
0
–0.2
–0.4
–0.6
–0.8
–1.0
–0.2
–0.4
–0.6
–0.8
–1.0
0.01
0.1
1
10
100
0.01
0.1
1
10
100
CURRENT CHANNEL (% of Full Scale)
CURRENT CHANNEL (% of Full Scale)
Figure 11. Reactive Energy Error as a Percentage of Reading (Gain = 1,
Power Factor = 0) over Temperature with Internal Reference,
Integrator Off
Figure 8. Active Energy Error as a Percentage of Reading (Gain = 1,
Temperature = 25°C) over Power Factor with Internal Reference,
Integrator Off
1.0
1.0
PF = +0.87
PF = 0
PF = –0.87
VDD = 2.97V
0.8
0.6
0.8
VDD = 3.30V
VDD = 3.63V
0.6
0.4
0.4
0.2
0.2
0
0
–0.2
–0.4
–0.6
–0.8
–1.0
–0.2
–0.4
–0.6
–0.8
–1.0
0.01
0.1
1
10
100
0.01
0.1
1
10
100
CURRENT CHANNEL (% of Full Scale)
CURRENT CHANNEL (% of Full Scale)
Figure 9. Active Energy Error as a Percentage of Reading (Gain = 1,
Temperature = 25°C, Power Factor = 1) over Supply Voltage with
Internal Reference, Integrator Off
Figure 12. Reactive Energy Error as a Percentage of Reading (Gain = 1,
Temperature = 25°C) over Power Factor with Internal Reference,
Integrator Off
Rev. 0 | Page 11 of 48
ADE7816
Data Sheet
1.0
0.8
1.0
0.8
VDD = 3.30V
VDD = 3.63V
VDD = 2.97V
0.6
0.6
0.4
0.4
0.2
0.2
0
0
–0.2
–0.4
–0.6
–0.8
–0.2
–0.4
–0.6
–0.8
–1.0
–1.0
0.01
0.1
1
10
100
0.1
1
10
100
CURRENT CHANNEL (% of Full Scale)
CURRENT CHANNEL (% of Full Scale)
Figure 13. Reactive Energy Error as a Percentage of Reading (Gain = 1,
Temperature = 25°C, Power Factor = 0) over Supply Voltage with
Internal Reference, Integrator Off
Figure 16. VRMS Error as a Percentage of Reading (Gain = 1,
Temperature = 25°C, Power Factor = 1) with Internal Reference,
Integrator Off
0.5
1.0
PF = +0.87
+85°C
PF = 0
PF = –0.87
+25°C
–40°C
0.4
0.8
0.3
0.2
0.6
0.4
0.1
0.2
0
0
–0.1
–0.2
–0.3
–0.4
–0.5
–0.2
–0.4
–0.6
–0.8
–1.0
45
50
55
60
65
0.1
1
10
100
FREQUENCY (Hz)
CURRENT CHANNEL (% of Full Scale)
Figure 14. Reactive Energy Error as a Percentage of Reading (Gain = 1,
Temperature = 25°C) over Frequency and Power Factor with
Internal Reference
Figure 17. Active Energy Error as a Percentage of Reading (Gain = 16,
Power Factor = 1) over Temperature with Internal Reference, Integrator On
1.0
0.8
1.0
PF = +0.5
PF = 1
PF = –0.5
0.8
0.6
0.6
0.4
0.4
0.2
0.2
0
0
–0.2
–0.4
–0.6
–0.8
–1.0
–0.2
–0.4
–0.6
–0.8
–1.0
0.1
1
10
100
0.1
1
10
100
CURRENT CHANNEL (% of Full Scale)
CURRENT CHANNEL (% of Full Scale)
Figure 18. Active Energy Error as a Percentage of Reading (Gain = 16,
Temperature = 25°C) over Power Factor with Internal Reference, Integrator On
Figure 15. IRMS Error as a Percentage of Reading (Gain = 1,
Temperature = 25°C, Power Factor = 1) with
Internal Reference, Integrator Off
Rev. 0 | Page 12 of 48
Data Sheet
ADE7816
1.0
1.0
0.8
+85°C
+25°C
–40°C
0.8
0.6
0.6
0.4
0.4
0.2
0.2
0
0
–0.2
–0.4
–0.6
–0.8
–1.0
–0.2
–0.4
–0.6
–0.8
–1.0
0.1
1
10
100
0.1
1
10
100
CURRENT CHANNEL (% of Full Scale)
CURRENT CHANNEL (% of Full Scale)
Figure 19. Reactive Energy Error as a Percentage of Reading (Gain = 16,
Power Factor = 0) over Temperature with Internal Reference, Integrator On
Figure 21. IRMS Error as a Percentage of Reading (Gain = 16,
Temperature = 25°C, Power Factor = 1) with Internal Reference,
Integrator On
1.0
PF = +0.87
PF = 0
PF = –0.87
0.8
0.6
0.4
0.2
0
–0.2
–0.4
–0.6
–0.8
–1.0
0.1
1
10
100
CURRENT CHANNEL (% of Full Scale)
Figure 20. Reactive Energy Error as a Percentage of Reading (Gain = 16,
Temperature = 25°C) over Power Factor with Internal Reference, Integrator On
Rev. 0 | Page 13 of 48
ADE7816
Data Sheet
TEST CIRCUIT
3.3V
26
+
+
0.22µF
0.22µF
4.7µF
4.7µF
24
5
3.3V
2
3
4
PULL_HIGH
PULL_LOW
RESET
39
38
SS/HSA
MOSI/SDA
10kΩ
1µF
MISO/HSD 37
7
8
IAP
IAN
36
35
SCLK/SCL
HSCLK
9
IBP
32
29
IRQ1
ADE7816
12
IBN
IRQ0
REF
17
28
IN/OUT
+
20pF
13 ICP
14
0.1µF
4.7µF
CLKOUT
CLKIN
ICN
16.384MHz
20pF
27
19 IFP
1
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
10
11
20
21
30
31
33
34
40
22 IEP
23 IDP
18
IN
15 VP
16
VN
6
25
Figure 22. Test Circuit
Rev. 0 | Page 14 of 48
Data Sheet
ADE7816
TERMINOLOGY
Measurement Error
when an ac signal (1ꢁ± mV rms at 1±± Hz) is introduced onto the
supplies. Any error introduced by this ac signal is expressed as a
percentage of reading (see the Measurement Error definition).
The error associated with the energy measurement made by the
ADE7816 is defined by the following equation:
Measurement Error =
Energy Registered by ADE7816 True Energy
For the dc PSR measurement, a reading at nominal supplies
(3.3 V) is taken. A second reading is obtained with the same
input signal levels when the power supplies are varied ±1±0.
Any error introduced is expressed as a percentage of the reading.
100%
True Energy
Phase Error Between Channels
ADC Offset Error
The high-pass filter (HPF) and digital integrator introduce
a slight phase mismatch between the current channels and the
voltage channel. The all digital design ensures that the phase
matching between the current channels and voltage channel in
all three phases is within ±±.1ꢀ over a range of 45 Hz to 65 Hz
and ±±.ꢁꢀ over a range of 4± Hz to 1 kHz. This internal phase
mismatch can be combined with the external phase error (from
current sensor or component tolerance) and calibrated with the
phase calibration registers.
ADC offset error refers to the dc offset that is associated with
the analog inputs to the ADCs. It means that, with the analog
inputs connected to AGND, the ADCs still see a dc analog input
signal. The magnitude of the offset depends on the gain and input
range selection (see the Typical Performance Characteristics
section). However, the HPF removes the offset from the current
channels and voltage channel, and the power calculation remains
unaffected by this offset.
Gain Error
Power Supply Rejection (PSR)
The gain error in the ADCs of the ADE7816 is defined as the
difference between the measured ADC output code (minus the
offset) and the ideal output code. The difference is expressed as
a percentage of the ideal code.
PSR quantifies the ADE7816 measurement error as a percentage
of reading when the power supplies are varied. For the ac PSR
measurement, a reading at nominal supplies (3.3 V) is taken.
A second reading is obtained with the same input signal levels
Rev. 0 | Page 15 of 48
ADE7816
Data Sheet
QUICK START
This section outlines the procedure for powering up and initializing
the ADE7816. Figure 23 shows a flow diagram of the initialization
steps. For detailed information, refer to the section of the data
sheet that pertains to each step, as indicated in Figure 23.
After power is supplied to the ADE7816 and communication
is established, a set of registers must be written (see Figure 23).
Table 8 lists details about each register.
The registers listed in Table 8 are essential for correct operation.
After these registers are set, enable any meter-specific features
before enabling the DSP to begin the energy calculations.
POWER UP THE
ADE7816
(SEE POWER AND
GROUND SECTION)
SET AND LOCK
COMMUNICATION MODE
(SEE COMMUNICATION
SECTION)
WTHR1 = 0x000002
WTHR0 = 0x000000
VARTHR1 = 0x000002
VARTHR0 = 0x000000
PCF_A_COEFF = 0x400CA4 (50Hz)
PCF_B_COEFF = 0x400CA4 (50Hz)
PCF_C_COEFF = 0x400CA4 (50Hz)
PCF_D_COEFF = 0x400CA4 (50Hz)
PCF_E_COEFF = 0x400CA4 (50Hz)
PCF_F_COEFF = 0x400CA4 (50Hz)
DICOEFF = 0xFFF8000
WRITE REQUIRED
REGISTER
DEFAULTS
CONFIGURE METER
SPECIFIC INTERRUPTS,
POWER QUALITY
FEATURES, AND
CALIBRATE
(SEE THE INTERRUPTS,
POWER QUALITY
FEATURES, AND ENERGY
CALIBRATION SECTIONS)
NOTE THAT THE FINAL
REGISTER SHOULD BE
WRITTEN 3 TIMES TO
CLEAR THE BUFFER
(SEE STARTING AND
STOPPING THE DSP
SECTION)
ENABLE THE ENERGY
METERING DSP
(SEE STARTING AND
STOPPING THE DSP
SECTION)
INITIALIZATION
COMPLETE
Figure 23. Quick Start
Table 8. Required Register Defaults
Register Register
Address Name
Register Description
Required Value
Reference Information
0x43AB
0x43AC
0x43AD
0x43AE
0x43B1
0x43B2
0x43B3
0x43B4
0x43B5
0x43B6
0x4388
WTHR1
Threshold register for active energy
0x000002
Refer to the Active Energy Threshold section.
Refer to the Active Energy Threshold section.
Refer to the Reactive Energy Threshold section.
Refer to the Reactive Energy Threshold section.
Refer to the Energy Phase Calibration section.
Refer to the Energy Phase Calibration section.
Refer to the Energy Phase Calibration section.
Refer to the Energy Phase Calibration section.
Refer to the Energy Phase Calibration section.
Refer to the Energy Phase Calibration section.
Refer to the Digital Integrator section.
WTHR0
Threshold register for active energy
0x000000
VARTHR1
Threshold register for reactive energy
Threshold register for reactive energy
Phase calibration for Current Channel A
Phase calibration for Current Channel B
Phase calibration for Current Channel C
Phase calibration for Current Channel D
Phase calibration for Current Channel E
Phase calibration for Current Channel F
0x000002
VARTHR0
0x000000
PCF_A_COEFF
PCF_B_COEFF
PCF_C_COEFF
PCF_D_COEFF
PCF_E_COEFF
PCF_F_COEFF
DICOEFF
0x400CA4 (50 Hz)
0x400CA4 (50 Hz)
0x400CA4 (50 Hz)
0x400CA4 (50 Hz)
0x400CA4 (50 Hz)
0x400CA4 (50 Hz)
0xFFF8000
Digital integrator algorithm; required only
if using di/dt sensors
Rev. 0 | Page 16 of 48
Data Sheet
ADE7816
INPUTS
The following section provides details on the ADE7816 input
connections that are required for correct functionality.
When the start-up sequence is complete, all registers are at their
default value, and the I2C port is the active serial port. Commu-
nication with the ADE7816 can begin. See the Communication
section for more details.
POWER AND GROUND
VDD and AGND, DGND
To start the energy and rms computations, the internal DSP
must be powered up after all configuration registers are set to
their desired values. The DSP is started by setting the run register
(Address 0xE228) to 0x0001. See the Starting and Stopping the
DSP section for more information.
To power the ADE7816, a 3.3 V dc input voltage should be
provided between the VDD pin and the AGND and DGND pins.
In addition, the PULL_HIGH and PULL_LOW pins must be
connected to 3.3 V and AGND, respectively. This configuration
is shown in Figure 24.
REFERENCE CIRCUIT
REFIN/OUT
3.3V
+
+
0.22µF
0.22µF
4.7µF
4.7µF
24
26
5
The nominal reference voltage at the REFIN/OUT pin is 1.2 V
0.075ꢀ. The REFIN/OUT pin can be overdriven by an external 1.2 V
reference source. If Bit 0 (EXTREFEN) in the CONFIG2 register
(Address 0xEC01) is cleared to 0 (the default value), the ADE7816
uses the internal voltage reference. If Bit 0 is set to 1, the external
voltage reference is used.
3.3V
2
3
PULL_HIGH
PULL_LOW
Figure 24. Applying Power to the ADE7816
The ADE7816 contains an on-chip power supply monitor that
supervises the power supply (VDD). When the voltage applied
to the VDD pin is below 2 V 10ꢀ, the chip is in an inactive
state. After VDD crosses the 2 V 10ꢀ threshold, the power
supply monitor keeps the ADE7816 in an inactive state for an
additional 26 ms. This time delay allows VDD to reach the
minimum specified operating voltage of 3.3 V − 10ꢀ. When
the minimum specified operating voltage is met and the
PULL_HIGH and PULL_LOW pins are tied to VDD and
AGND, respectively, the internal circuitry is enabled. This
process is accomplished in approximately 40 ms.
The voltage of the ADE7816 internal reference drifts slightly with
temperature; see the Specifications section for the temperature
coefficient specification (in ppm/°C). The value of the temperature
drift varies from part to part. Because the reference is used for
all ADCs, any xꢀ drift in the reference results in a 2xꢀ deviation
of the meter accuracy.
RESET
Hardware Reset
RESET
pin returns high,
To initiate a hardware reset of the ADE7816, the
RESET
pin must
be pulled low for at least 10 μs. After the
all registers return to their default values. The ADE7816 signals the
IRQ1
low and setting Bit 15 (RSTDONE) in the STATUS1 register to 1.
This bit is set to 0 during the transition period and changes to 1
when the transition ends.
When the start-up sequence is complete and the ADE7816 is
ready to receive communication from a microcontroller, the
RSTDONE flag is set in the STATUS1 register (Address 0xE503).
end of the transition period by triggering the
interrupt pin
IRQ1
An external interrupt is triggered on the
pin. The RSTDONE
interrupt is enabled by default and cannot be disabled; therefore,
an external interrupt always occurs at the end of a power-up
procedure or hardware or software reset.
Software Reset Functionality
Bit 7 (SWRST) in the CONFIG register (Address 0xE618) manages
the software reset functionality in the ADE7816. The default value
of this bit is 0. If Bit 7 is set to 1, the ADE7816 enters the software
reset state. In this state, all internal registers are set to their default
values, with the exception of the CONFIG2 register, which retains
its existing value. In addition, the choice of which serial port is in
use (I2C or SPI) remains unchanged if the lock-in procedure was
executed previously (see the Communication section for details).
It is highly recommended that the RSTDONE interrupt be used
by the microcontroller to gate the first communication with the
ADE7816. If the interrupt is not used, a timeout can be imple-
mented. However, because the start-up sequence can vary from
part to part and over temperature, a timeout of a least 100 ms is
recommended. The RSTDONE interrupt provides the most time-
efficient way of monitoring the completion of the ADE7816
start-up sequence.
When the software reset ends, Bit 7 (SWRST) in the CONFIG
The AVDD and DVDD output pins provide access to the on-
chip analog and digital LDOs. When the ADE7816 is fully
powered up, these pins are at 2.5 V. If the internal reference is
being used, the REFIN/OUT pin outputs 1.2 V (see the Reference
Circuit section).
IRQ1
register is cleared to 0, the
interrupt pin is set low, and Bit 15
(RSTDONE) in the STATUS1 register is set to 1. RSTDONE is
set to 0 during the transition period and changes to 1 when the
transition ends.
It is recommended that all meters be designed to have both
software and hardware reset capability.
Rev. 0 | Page 17 of 48
ADE7816
Data Sheet
PGA Gain
CLKIN AND CLKOUT
The ADE7816 has three internal PGA gain amplifiers that can
be used to amplify the input signals by ×2, ×4, ×8 or ×16. The
PGA gain stage is often required when using a current sensor
that produces a low output voltage, such as Rogowski coils.
PGA1 affects Current Channel A, Current Channel B, and
Current Channel C and is controlled by Bits[2:5] (PGA1) of
the gain register (Address 5xE65F). PGA2 affects the voltage
channel and is controlled by Bits[±:3] (PGA2) of the gain register.
PGA3 affects Current Channel D, Current Channel E, and
Current Channel F and is controlled by Bits[8:6] (PGA3) of
the gain register.
An external clock or parallel resonant crystal is required to
clock the ADE7816. If an external clock source is being used,
it should be connected to the CLKIN pin. The required clock
frequency for specified operation is 16.384 MHz. Alternatively,
a parallel resonant AT-cut crystal can be connected across the
CLKIN and CLKOUT pins. The ADE7816 has no internal load
capacitance and, therefore, load capacitors based on the data
sheet of the crystal manufacturer should be added on each pin.
ANALOG INPUTS
Input Pins
The ADE7816 has seven analog inputs that form six current
channels and one voltage channel. Current Channel A, Current
Channel B, and Current Channel C each consist of a pair of dif-
ferential input pins: IAP and IAN, IBP and IBN, and ICP and ICN.
Current Channel D, Current Channel E, and Current Channel F
all share a common reference, IN, and, therefore, are single-ended.
For consistency, it is recommended that all six current inputs be
connected in a single-ended configuration (see Figure 26 and
Figure 27). The voltage channel is a fully differential input that
consists of a pair of inputs: VP and VN. The voltage channel is
typically connected in a single-ended configuration.
Table 9 lists details on how the PGA gain affects the full-scale
input voltage.
Table 9. PGA Gain
Full-Scale
Gain Register (Address 0xE60F)
Single-Ended
Gain
Input (mV)
PGA1[2:0]
PGA2[5:3]
PGA3[8:6]
1
±±00
000
000
000
2
±2±0
001
001
001
4
±12±
010
010
010
8
±ꢀ2.±
011
011
011
1ꢀ
±ꢁ1.2±
100
100
100
The maximum input voltage that should be applied to any input
channel is ±±55 mV. The maximum common-mode signal that is
allowed on the inputs is ±2± mV. Figure 2± shows a schematic of
the inputs and their relation to the maximum common-mode
voltage.
Digital Integrator
The ADE7816 includes a digital integrator that must be enabled
when using a di/dt sensor such as a Rogowski coil. This integrator
is enabled by setting the INTEN bit (Bit 5) of the CONFIG register
(Address 5xE618) to 1. When using the digital integrator, the
DICOEFF register (Address 5x4388) should be written to
5xFFF8555. For more details on the theory behind the digital
integrator, refer to the AN-1137 Application Note.
DIFFERENTIAL INPUT
V
+ V = 500mV MAX PEAK
1
2
COMMON MODE
V
1
V
= ±25mV MAX
CM
+500mV
VP
V
V
1
V
CM
VN
CM
–500mV
Figure 25. Maximum Input Level
Rev. 0 | Page 18 of 48
Data Sheet
ADE7816
Antialiasing Filters
However, a di/dt sensor, such as a Rogowski coil, has a 20 dB per
decade gain. This neutralizes the 20 dB per decade attenuation
produced by the low-pass filter (LPF). Therefore, when using a
di/dt sensor, a second pole is required. One simple approach is
to cascade one additional RC filter, thereby producing a −40 dB
per decade attenuation (see Figure 27).
Each analog input pin requires that a simple RC filter be connected
to the input. The role of the RC filter is to prevent aliasing. The
aliasing effect is caused by frequency components (which are
higher than half the sampling rate of the ADC) folding back and
appearing in the sampled signal at a frequency that is below half
the sampling rate. Aliasing is an artifact of all sampled systems.
For conventional current sensors, it is recommended that one
RC filter with a corner frequency of 5 kHz be used for the
attenuation to be sufficiently high at the sampling frequency
of 1.024 MHz. The 20 dB per decade attenuation of this filter
is usually sufficient to eliminate the effects of aliasing for
conventional current sensors (see Figure 26).
PHASE
100Ω
1kΩ
22nF
IAP
22nF
ADE7816
ROGOWSKI
COIL
100Ω
1kΩ
22nF
IAN
LOAD
22nF
PHASE
1kΩ
IAP
22nF
Figure 27. Rogowski Coil Input Connections
ADE7816
RB
CURRENT
TRANSFORMER
1kΩ
IAN
LOAD
22nF
Figure 26. Current Transformer Input Connections
Rev. 0 | Page 19 of 48
ADE7816
Data Sheet
ENERGY MEASUREMENTS
This section describes the energy measurements available in
the ADE7816. For information about the theory behind these
measurements, refer to the AN-1137 Application Note.
CWATTHR (Address 0xE402), DWATTHR (Address 0xE403),
EWATTHR (Address 0xE404) and FWATTHR (Address 0xE405).
All active energy registers are in 32-bit, signed format. The
ADE7816 accumulates both positive and negative power. Negative
power indicates that the angle between the voltage and current is
greater than 90°, and power is being injected back into the grid.
The ADE7816 provides a signed accumulation of the power;
positive power is added and negative power is subtracted.
Figure 28 shows the configurations of the active energy signal path.
STARTING AND STOPPING THE DSP
To obtain energy measurements, the internal processor must first
be started by setting the run register (Address 0xE228) to 0x0001.
It is recommended that all registers be initialized before starting
the DSP and that the last register in the queue be written three
times to flush the pipeline. When this procedure is complete, the
DSP should be started. There is no reason to stop the DSP, once
started, because all of the registers can be modified while the DSP
is running. The DSP can be stopped, however, by writing 0x0000
to the run register.
Active Energy Threshold
The ADE7816 accumulates energy in two steps (see Figure 28).
The first step occurs internally, using the two threshold registers,
WTHR1 (Address 0x43AB) and WTHR0 (Address 0x43AC).
These registers make up the most significant and least significant
24 bits, respectively, of an internal threshold register that is used
to control the frequency at which the external xWATTHR registers
are updated. The WTHR1 and WTHR0 registers affect all six active
energy measurements. For standard operation, the WTHR1 regi-
ster should be set to 0x2 and the WTHR0 register set to 0x0.
Thus, the update rate of the xWATTHR registers is set to slightly
below the maximum of 8 kHz with full-scale inputs. If the rate at
which energy is accumulated in the xWATTHR registers must be
reduced, the WTHR1and WTHR0 registers can be modified.
Within the DSP core, there is a two-stage pipeline. This means
that when a single register must be initialized, two or more writes
are required to ensure that the value has been written. If two or
more registers must be initialized, the last register must be written
two more times to ensure that the value is written into the RAM.
It is recommended that the last register be written three times to
ensure successful communication. See the Register Protection
section for details on protecting these registers.
ACTIVE ENERGY MEASUREMENT
Definition of Active Power and Active Energy
8 kHz
Threshold = 0x2000000 ×
(2)
Active power is the product of voltage and current and is the
power dissipated in a purely resistive load. Active energy is the
accumulation of active power over time and is measured in watts.
Required Update Rate (kHz)
Note that the maximum output with full scale inputs is 8 kHz.
Do not adjust the threshold to try to produce more than 8 kHz.
Such an adjustment may result in saturation of the output
frequency and, therefore, a loss of accuracy.
The average power over an integral number of line cycles (n) is
given by the following expression:
nT
1
The second stage of the accumulation occurs in the external
registers, xWATTHR. With the recommended values provided
in Equation 2, the energy updates at a rate of 8 kHz with full-
scale inputs (see Figure 28).
P =
= VI
(1)
P(t)dt
∫
nT
0
where:
V is the rms voltage.
I is the rms current.
Energy Accumulation and Register Roll-Over
P is the active or real power.
T is the line cycle period.
As shown in Equation 2, the active energy accumulates at a maxi-
mum rate of 8 kHz with full-scale inputs. The maximum positive
value that the 32-bit, signed xWATTHR registers can store before
they overflow is 0x7FFFFFFF. Assuming steady accumulation
with full-scale inputs, the accumulation time is
Active Energy Registers
The ADE7816 has six active energy registers, where the active
energy is accumulated for each of the six channels separately:
AWATTHR (Address 0xE400), BWATTHR (Address 0xE401),
Time = 0x7FFFFFFF × 125 ꢁs = 74 hr, 33 min, 55 sec
DIGITAL
INTEGRATOR
IAGAIN
IA
AWATTOS AWGAIN
HPF
HPF
AWATTHR[31:0]
ACCUMULATOR
32-BIT
PCF_A_COEFF VGAIN
VA
LPF
REGISTER
WTHR[47:0]
Figure 28. Active Energy Signal Path
Rev. 0 | Page 20 of 48
Data Sheet
ADE7816
The content of the active energy register overflows from full-scale
positive (0x7FFFFFFF) to full-scale negative (0x80000000) and
continues to increase in value when the active power is positive.
Conversely, if the active power is negative, the energy register
underflows from full-scale negative (0x80000000) to full-scale
positive (0x7FFFFFFF) and continues decreasing in value. Bit 0
(AEHF1) in the STATUS0 register (Address 0xE502) is set when
Bit 30 in the AWATTHR, BWATTHR, or CWATTHR register
changes, signifying that one of these registers is half full. Simi-
larly, Bit 1 (AEHF2) in the STATUS0 register is set when Bit 30
in the DWATTHR, EWATTHR, or FWATTHR register changes,
signifying that one of these registers is half full.
Reactive Energy Threshold
The ADE7816 accumulates energy in two steps. The first
is done internally using the threshold registers, VARTHR1
(Address 0x43AD) and VARTHR0 (Address 0x43AE). These
registers make up the most significant and least significant 24 bits,
respectively, of an internal threshold register that is used to control
the frequency at which the external xVARHR registers are updated.
The VARTHR1 and VARTHR0 registers affect all six reactive
energy measurements. For standard operation, the VARTHR1
register should be set to 0x2 and the VARTHR0 register set to
0x0. This sets the update rate of the xVARHR registers to the
maximum of 8 kHz with full-scale inputs.
Setting Bit 6 (RSTREAD) in the LCYCMODE register
(Address 0xE702) enables a read-with-reset for all watt-hour
accumulation registers. When this bit is set, all energy accu-
mulation registers are set to 0 following a read operation.
If the rate at which energy is accumulated in the xVARHR
registers must be reduced, VARTHR1 and VARTHR0 can be
modified as follows:
8 kHz
Threshold = 0x2000000 ×
(4)
REACTIVE ENERGY MEASUREMENT
Required Update Rate (kHz)
Definition of Reactive Power and Reactive Energy
Note that the maximum output with full scale inputs is 8 kHz.
The threshold should not be adjusted to try to produce more
than 8 kHz. Such an adjustment could result in saturation of the
output frequency and, therefore, a loss of accuracy.
Reactive power is the product of the voltage and current when all
harmonic components of one of these signals are phase shifted
by 90°. Reactive power is the power dissipated in an induc-tive or
capacitive load and is measured as volt-ampere reactive (var).
Reactive energy is the accumulation of reactive power over time.
The second stage of the accumulation is done in the external
registers, xVARHR. With the recommended values provided in
Equation 4, the reactive energy updates at a rate of 8 kHz with
full-scale inputs (see Figure 29).
nT
1
RP =
= VI × sin(θ)
RP t dt
(3)
(
)
∫
nT
0
Reactive Energy Accumulation and Register Roll-Over
where:
The reactive energy accumulates at a maximum rate of 8 kHz
with full-scale inputs. The maximum positive value that the 32-bit,
signed xVARHR registers can store before they overflow is
0x7FFFFFFF. Assuming steady accumulation with full-scale
reactive energy inputs, the accumulation time is
V is the rms voltage.
I is the rms current.
RP is the reactive or real power.
T is the line cycle period.
Reactive Energy Registers
Time = 0x7FFFFFFF × 125 ꢁs = 74 hr, 33 min, 55 sec
The ADE7816 has six reactive energy registers that accumulate
active energy for each of the six channels separately: AVARHR
(Address 0xE406), BVARHR (Address 0xE407), CVARHR
(Address 0xE408), DVARHR (Address 0xE409), EVARHR
(Address 0xE40A), and FVARHR (Address 0xE40B). All
reactive energy registers are in 32-bit, signed format. The
ADE7816 accumulates both positive and negative reactive
power. Negative reactive power indicates that the current
is leading the voltage by up to 180°. The ADE7816 provides
a signed accumulation of the power, where positive power
is added and negative is subtracted.
Conversely, if the reactive power is negative, the energy register
underflows from full-scale negative (0x80000000) to full-scale
positive (0x7FFFFFFF) and continues decreasing in value. Bit 2
(REHF1) in the STATUS0 register is set when Bit 30 of the
AVARHR, BVARHR, or CVARHR register changes, signifying
that one of these registers is half full. Similarly, Bit 3 (REHF2)
in the STATUS0 register is set when Bit 30 of the DVARHR,
EVARHR, or FVARHR register changes, signifying that one
of these registers is half full.
DIGITAL
INTEGRATOR
IAGAIN
IA
AVAROS AVARGAIN
HPF
AVARHR[31:0]
TOTAL
REACTIVE
POWER
ALGORITHM
ACCUMULATOR
VARTHR[47:0]
PCF_A_COEFF VGAIN
VA
32-BIT
REGISTER
HPF
Figure 29. Reactive Energy Signal Path
Rev. 0 | Page 21 of 48
ADE7816
Data Sheet
The reactive energy register content overflows from full-scale
positive (0x7FFFFFFF) to full-scale negative (0x80000000) and
continues to increase in value when the reactive power is positive.
time should be written to the LINECYC register (Address 0xE60C)
as an integer number of half line cycles. The ADE7816 can
accumulate energy for up to 65,535 half line cycles. This equates
to an accumulation period of approximately 655 sec with 50 Hz
inputs, and 546 sec with 60 Hz inputs.
Setting Bit 6 (RSTREAD) of the LCYCMODE (Address 0xE702)
register enables a read-with-reset for all reactive energy accu-
mulation registers. When this bit is set, all energy accumulation
registers are set to 0 following a read operation.
The number of half line cycles written to the LINECYC register
is used for the active and reactive line cycle accumulation on all
six channels. At the end of a line cycle accumulation period, the
xWATTHR and xVARHR registers are updated and the LENERGY
flag is set in the STATUS0 register (Address 0xE502). If the
LENERGY bit in the MASK0 register (Address 0xE50A) is set,
LINE CYCLE ACCUMULATION MODE
In the active and reactive line cycle accumulation mode, the
energy accumulation of the ADE7816 is synchronized to the
voltage channel zero crossing, so that the active and reactive
energy can be accumulated over an integral number of half line
cycles. This feature is available for the active and reactive energy
accumulation on all six channels. The advantage of summing
the active and reactive energy over an integral number of half
line cycles is that the sinusoidal component of the energy is
reduced to 0. This eliminates any ripple in the energy calculation.
Accurate energy is calculated in a shorter time because the
integration period can be shortened. The line cycle accumulation
mode can be used for fast calibration and to obtain the average
power over a specified time period. Figure 30 shows a diagram
of the active energy line cycle accumulation mode signal path.
IRQ0
an external interrupt is issued on the
pin. Another accu-
mulation cycle begins immediately, as long as the LWATT and
LVAR bits in the LCYCMODE register remain set.
The contents of the xWATTHR and xVARHR registers are updated
synchronous to the LENERGY flag. The xWATTHR and xVARHR
registers hold their current values until the end of the next line
cycle period, when the contents are replaced with the new reading
(see Figure 30 and Figure 31). When using the line cycle accu-
mulation mode, Bit 6 (RSTREAD) of the LCYCMODE register
should be set to Logic 0 because the read-with-reset function of
the energy registers is not available in this mode.
Note that, when line cycle accumulation mode is first enabled,
the reading after the first LENERGY flag should be ignored
because it may be inaccurate. This inaccuracy is due to the line
cycle accumulation mode not being synchronized to the zero
crossing. As a result, the first reading may not be taken over
a complete number of half line cycles. After the first line cycle
accumulation is completed, all successive readings are correct.
Active and reactive energy line cycle accumulation modes are
disabled by default and can be enabled on all six channels by setting
Bit 0 (LWATT) and Bit 1 (LVAR), respectively, in the LCYCMODE
register. Bit 3 (ZX_SEL) of the LCYCMODE register must also be
set to enable the voltage channel zero-crossing counter to be used
in the line cycle accumulation measurement. The accumulation
xWATTOS
xWGAIN
48
0
+
OUTPUT
FROM
LPF
+
INTERNAL
ACCUMULATION
WTHR[48:0]
OUTPUT FROM
VOLTAGE CHANNEL
ADC
ZERO-CROSSING
DETECTION
CALIBRATION
CONTROL
LPF_ZX
23
0
xWATTHR
15
0
LINECYC
Figure 30. Line Cycle Accumulation for xWATTHR
xVAROS
xVARGAIN
48
0
+
+
OUTPUT FROM
REACTIVE POWER
ALGORITHM
INTERNAL
ACCUMULATION
VARTHR[48:0]
OUTPUT FROM
VOLTAGE CHANNEL
ADC
ZERO-CROSSING
DETECTION
CALIBRATION
CONTROL
LPF_ZX
23
0
xVARHR
15
0
LINECYC
Figure 31. Line Cycle Accumulation for xVARHR
Rev. 0 | Page 22 of 48
Data Sheet
ADE7816
VARNOLOAD (Address 0x43B0) registers. When in the no
ROOT MEAN SQUARE MEASUREMENT
load condition, the active and reactive energies are no longer
accumulated in the energy registers. Note that each of the six
channels has a separate no load circuit.
Root mean square (rms) is a measurement of the magnitude of
an ac signal. Specifically, the rms of an ac signal is equal to the
amount of dc required to produce an equivalent amount of power
in the load. The ADE7816 provides rms measurements on the
six current channels and the voltage channel simultaneously.
These measurements have a settling time of approximately 440 ms
with the integrator off and 500 ms with the integrator on. The
registers are updated every 125 μs. The rms value is measured
over a 2 kHz bandwidth.
Setting the No Load Thresholds
The APNOLOAD and VARNOLOAD registers are compared
to the active and reactive powers, respectively, to set the no load
threshold. With full-scale inputs on both the current and voltage
channel, the maximum power is 0x1FF6A6B. The no load
threshold should, therefore, be set with respect to this maxi-
mum power, as follows:
The 24-bit, unsigned voltage rms measurement is available in the
VRMS register (Address 0x43C0). Similarly, the six current channel
rms measurements are available in the IARMS (Address 0x43C1),
IBRMS (Address 0x43C2), ICRMS (Address 0x43C3), IDRMS
(Address 0x43C4), IERMS (0x43C5), and IFRMS (Address 0x43C6)
registers. All registers are updated at a rate of 8 kHz. Figure 32
shows the IxRMS signal path. A similar signal path is used on
the voltage channel to compute the VRMS measurement.
APNOLOAD =
0x1FF6A6B × V% of Full_Scale × I(noload)% of Full_Scale
(5)
For example, if the nominal voltage is set to 50ꢀ of full scale
and the current channel no load threshold is required to be at
0.01ꢀ of full scale, the APNOLOAD threshold is
APNOLOAD = 0x1FF6A6B × 50ꢀ × 0.01ꢀ = 0x68C
(6)
The VARNOLOAD register is usually set to the same value as
that of the APNOLOAD register. When the APNOLOAD and
VARNOLOAD registers are set to negative values, the no load
detection circuit is disabled.
Due to nonidealities in the internal filtering, it is recommended
that the IxRMS registers be read synchronously to the zero-
crossing signal (see the Zero-Crossing Detection section). This
helps to stabilize reading-to-reading variation by removing the
effect of any 2ω ripple that is present on the rms measurement.
Bit 0 (NLOAD1) in the STATUS1 register (Address 0xE503) is set
when the no load condition occurs on the A, B, or C current chan-
nel. Bit 1 (NLOAD2) in the STATUS1 register is set when the
load condition occurs on the D, E, or F current channel. Bits[5:0]
(NOLOADx) in the CHNOLOAD register (Address 0xE608)
can be used to determine which channel caused the no load
condition. When NOLOADx is cleared to 0, the channel is not in
a no load condition. When NOLOADx is set to 1, the channel is
in a no load condition.
With the specified full-scale analog input signal of 0.5 V, the
rms value of a sinusoidal signal is 4,191,910 (0x3FF6A6),
independent of line frequency. If the integrator is enabled on
the current channels, the equivalent current rms value of a full-
scale sinusoidal signal at 50 Hz is 4,191,910 (0x3FF6A6). At
60 Hz, it is 3,493,258 (0x354D8A).
NO LOAD DETECTION
The ADE7816 includes a no load detection feature that eliminates
meter creep. Meter creep is defined as excess energy that is
accumulated by the meter when there is no load attached. The
ADE7816 warns of this condition and stops energy accumulation
if the energy falls below a programmable threshold. The ADE7816
includes a no load feature on the active and reactive energy
measurements. This allows a true no load condition to be
detected.
No Load Interrupt
The ADE7816 includes two interrupts that are associated with
the no load feature. The first is associated with the A, B, and C
current channels, and it can be enabled by setting Bit 0 (NLOAD1)
in the MASK1 register (Address 0xE50B). The second interrupt
is associated with the D, E, and F current channels; it can be
enabled by setting Bit 1 (NLOAD2) in the MASK1 register. If
the corresponding interrupt is enabled, the no load condition
The no load condition is triggered when the absolute values of
the active and reactive powers are less than or equal to a thresh-
old that is specified in the APNOLOAD (Address 0x43AF) and
IRQ1
causes the external
section).
pin to go low (see the Interrupts
IxRMSOS[23:0]
7
2
CURRENT SIGNAL FROM
2
x
IxRMS[23:0]
HPF OR INTEGRATOR
(IF ENABLED)
√
LPF
Figure 32. IxRMS Signal Path
Rev. 0 | Page 23 of 48
ADE7816
Data Sheet
ENERGY CALIBRATION
DVARGAIN (Address 0x43A3), EVARGAIN (Address 0x43A5),
and FVARGAIN (Address 0x43A7) registers control the reactive
power gain calibration on the B through F current channels,
respectively. The xVARGAIN registers affect the reactive power
in the same way that the xWGAIN registers affect the active power.
Equation 9 shows the relationship between gain adjustment and
the xVARGAIN registers.
CHANNEL MATCHING
The ADE7816 provides individual channel gain registers that
allow the six current channels and the voltage channel to be
matched. Matching the channels simplifies the calibration process.
The IAGAIN (Address 0x4381), IBGAIN (Address 0x4382),
ICGAIN (Address 0x4383), IDGAIN (Address 0x4384),
IEGAIN (Address 0x4385), and IFGAIN (Address 0x4386)
registers adjust the A through F current channels, respectively,
whereas the VGAIN register (Address 0x4380) can be used to
adjust the voltage channel. The default value of the IxGAIN
registers is 0x00000, which corresponds to no channel gain. The
IxGAIN can adjust the channel gain by up to 100ꢀ. The channel
is scaled by −50ꢀ by writing 0xC00000 to the corresponding
IxGAIN register, and it is increased by +50ꢀ by writing 0x400000.
Equation 7 shows the relationship between the IxGAIN register
and the rms measurement.
xVARGAIN
⎛
⎜
⎝
⎞
⎟
⎠
Reactive Power = Reactive Power0 ×
(9)
+1
0x800000
ENERGY OFFSET CALIBRATION
The ADE7816 includes offset calibration registers for the active
and reactive powers on all six channels. Offsets can exist in the
power calculations due to crosstalk between channels on the
PCB and in the ADE7816. The offset calibration allows these
offsets to be removed to increase the accuracy of the measure-
ment at low input levels.
IxGAIN
223
⎛
⎜
⎞
⎟
I
rms = Irms
×
(7)
0
1+
The active power offset can be corrected on Current Channel A
by adjusting the AWATTOS (Address 0x4392) register. The
BWATTOS (Address 0x4394), CWATTOS (Address 0x4396),
DWATTOS (Address 0x4398), EWATTOS (Address 0x439A),
and FWATTOS (Address 0x439C) registers control the active
power offset calibration on the B through F current channels,
respectively. The xWATTOS registers are 24-bit, signed, twos
complement registers with default values of 0. One LSB in the
active power offset register is equivalent to 1 LSB in the active
power multiplier output. With full-scale current and voltage
inputs, the maximum power output is equal to 1FF6A6B =
33,516,139. At −80 dB down from full scale (active power scaled
down 104 times), one LSB of the xWATTOS registers represents
0.0298ꢀ. Equation 10 shows the relationship between the
xWATTOS registers and the active energy reading.
⎝
⎠
VGAIN
223
⎛
⎜
⎝
⎞
⎟
⎠
V
rms = Vrms
×
0
1+
where Irms and Vrms0 are the current and voltage rms
0
measurements, respectively, without offset correction.
Changing the content of the IxGAIN registers affects all calcu-
lations based off that channel, including the active and reactive
energy. Therefore, it is recommended that the channel matching
be performed first in the calibration procedure.
ENERGY GAIN CALIBRATION
The active and reactive energy measurements can be calibrated
on all six channels separately. This separate calibration allows
compensation for meter-to-meter gain variation.
xWATTHR = xWATTHR0 +
(10)
The AWGAIN register (Address 0x4391) controls the active
power gain calibration on Current Channel A. The BWGAIN
(Address 0x4393), CWGAIN (Address 0x4395), DWGAIN
(Address 0x4397), EWGAIN (Address 0x4399), and FWGAIN
(Address 0x439B) registers control the active power gain calibra-
tion on the B through F current channels, respectively. The default
value of the xWGAIN registers is 0x00000, which corresponds to
no gain calibration. The xWGAIN registers can adjust the active
power by up to 100ꢀ. The output is scaled by −50ꢀ by writing
0xC00000 to the watt gain registers, and it is increased by +50ꢀ
by writing 0x400000 to them. Equation 8 shows the relationship
between the gain adjustment and the xWGAIN registers.
8000
⎛
⎜
⎞
⎟
× xWATTOS × AccumulationTime(s)
WTHR
⎝
⎠
Similar offset calibration registers are available for the reactive
power. The reactive power on Current Channel A can be offset
calibrated using the AVAROS (Address 0x439E). The BVAROS
(Address 0x43A0), CVAROS (Address 0x43A2), DVAROS
(Address 0x43A4), EVAROS (Address 0x43A6), and FVAROS
(Address 0x43A8) registers control the reactive power gain
calibration on the B through F current channels, respectively.
The xVAROS registers affect the reactive powers in the same way
that the xWATTOS registers affect the active power. Equation 11
shows the relationship between the xVAROS registers and the
reactive energy reading.
xWGAIN
⎛
⎜
⎞
⎟
Active Power = Active Power0 ×
(8)
+1
0x800000
⎝
⎠
Similar gain calibration registers are available for the reactive
power. The reactive power on Current Channel A can be gain
calibrated using the AVARGAIN (Address 0x439D) register. The
xVARHR = xVARHR0 +
(11)
8000
⎛
⎜
⎞
⎟
× xVAROS × AccumulationTime(s)
VARTHR
⎝
⎠
BVARGAIN (Address 0x439F), CVARGAIN (Address 0x43A1),
Rev. 0 | Page 24 of 48
Data Sheet
ADE7816
To simplify this calculation, Analog Devices has a spreadsheet
file that calculates this value. To obtain this spreadsheet, contact
a representative of Analog Devices.
ENERGY PHASE CALIBRATION
The ADE7816 is designed to function with a variety of current
transducers, including those that induce inherent phase errors.
A phase error of 0.1° to 0.3° is not uncommon for a current
transformer (CT). These phase errors can vary from part to
part, and they must be corrected to achieve accurate power
readings. The errors associated with phase mismatch are
particularly noticeable at low power factors. The ADE7816
provides a means of digitally calibrating these small phase
errors by introducing a time delay or a time advance.
By default, the PCF_x_COEFF registers are set to 0. This setting
does not, however, result in a 0° phase shift. On startup, the
PCF_x_COEFF registers should be set to 0x400C4A for a 50 Hz
system and 0x401235 for a 60 Hz system.
RMS OFFSET CALIBRATION
The ADE7816 includes an rms offset compensation register for
each channel, as follows: IARMSOS (Address 0x438B), IBRMSOS
(Address 0x438C), ICRMSOS (Address 0x438D), IDRMSOS
(Address 0x438E), IERMSOS (Address 0x438F), IFRMSOS
(Address 0x4390), and VRMSOS (Address 0x438A). These 24-bit,
signed registers are used to remove offsets in the current and
voltage rms calculations. The rms offset compensation register
is added to the squared current and voltage signal before the
square root is executed. Equation 15 shows the relationship
between the rms measurement and the offset adjustment.
Because different sensors can be used on each channel, sepa-
rate phase calibration registers are included all six channels.
The PCF_A_COEFF register (Address 0x43B1) can be used to
correct phase errors on Current Channel A. The PCF_B_COEFF
(Address 0x43B2), PCF_C_COEFF (Address 0x43B3), PCF_D_
COEFF (Address 0x43B4), PCF_E_COEFF (Address 0x43B5),
and PCF_F_COEFF (Address 0x43B6) registers control the phase
calibration on the B through F current channels, respectively. All
registers are 24-bit, unsigned.
(15)
Irms
= Irms2 +128× IxRMSOS
0
The ADE7816 uses all pass filters to accurately add time advances
and delays to the current channels with respect to the voltage
channels. A separate filter is included on each of the six current
channels. To adjust the time delay or advance, the coefficient of
these filters must be adjusted. Equation 12, Equation 13, and
Equation 14 show how the coefficients correspond to the phase
offset in radians.
Vrms = Vrms2 +128×VRMSOS
0
where Irms and Vrms0 are the current and voltage rms
0
measurement, respectively, without offset correction.
sin(θ + 3ω) − sinω
PCF_x_COEFFFRACTION
=
(12)
sin(θ + 4ω)
If PCF_x_COEFF ≥ 0, then
PCF_x_COEFF = 223 × PCF_x_COEFFFRACTION
(13)
If PCF_x_COEFF < 0, then
PCF_x_COEFF = (223 + 2328) × PCF_x_COEFFFRACTION (14)
where θ is the required current-to-voltage phase adjustment.
Linefreq(Hz)
ω = 2π
8000
Rev. 0 | Page 25 of 48
ADE7816
Data Sheet
POWER QUALITY FEATURES
This section describes the power quality features that are available
in the ADE7816.
also be configured to trigger an interrupt on the external pin
by setting the DREADY bit (Bit 17) in the MASK0 register
(Address 0xE50A). With the specified full-scale analog input
signal of 0.5 V, the expected reading on the current and voltage
waveform register is approximately 5,989,256 (dec).
SELECTING A CURRENT CHANNEL GROUP
When using the power quality features on the current channels,
the group of channels to be monitored must be selected. Bit 14
(CHANNEL_SEL) of the COMPMODE register (Address 0xE60E)
can be used to make this selection. To select the A, B, and C current
channels for the current channel power quality measurements,
CHANNEL_SEL must be set to 0 (default). To select the D, E,
and F current channels for the current channel power quality
measurements, CHANNEL_SEL must be set to 1. If all channels
require monitoring, the monitoring must be done in series by
modifying the CHANNEL_SEL bit after data is obtained. The
settling time of each power quality measurement is provided in
the section that pertains to each power quality feature.
The instantaneous waveforms have no additional settling time,
and, therefore, if the CHANNEL_SEL bit is modified to change
the group of current channels being measured, the new result is
available in 125 μs (8 kHz).
ZERO-CROSSING DETECTION
Zero-Crossing Detection
The ADE7816 has a zero-crossing (ZX) detection circuit on the
voltage and current channels. Zero-crossing detection allows
measurements to be synchronized to the frequency of the
incoming waveforms.
INSTANTANEOUS WAVEFORMS
The zero-crossing events are filtered internally by an LPF. The
LPF is intended to eliminate all harmonics of 50 Hz and 60 Hz
systems, and to help identify the zero-crossing events on the
fundamental components of both current and voltage channels.
The digital filter has a pole at 80 Hz and is clocked at 256 kHz.
As a result, there is a phase lag between the analog input signal
and the output of the LPF. The error in ZX detection is 0.0703°
for 50 Hz systems and 0.0843° for 60 Hz systems. The phase lag
response of the LPF results in a time delay of approximately
31.4° or 1.74 ms (at 50 Hz) between its input and output. The
overall delay between the zero crossing on the analog inputs and
the ZX detection that is obtained after LPF1 is about 39.6° or
2.2 ms (at 50 Hz). Figure 33 shows how the zero-crossing signal
is detected.
The ADE7816 provides access to the current and voltage channel
waveform data. This information allows the instantaneous data
to be analyzed in more detail, including reconstruction of the
current and voltage input for harmonic analyses. These measure-
ments are available from a set of 24-bit, signed registers. The
voltage channel has a dedicated register, VWV (Address 0xE510),
whereas the current channels share three registers: IAWV/IDWV
(Address 0xE50C), IBWV/IEWV (Address 0xE50D), and ICWV/
IFWV (Address 0xE50E). A group of current channels (A, B, C
or D, E, F) must be selected by Bit 14 (CHANNEL_SEL) of the
COMPMODE register (see the Selecting a Current Channel
Group section).
All measurements are updated at a rate of 8 kHz. The ADE7816
provides an interrupt status bit, DREADY (Bit 17 of the STATUS0
register, Address 0xE502), that is triggered at a rate of 8 kHz,
allowing measurements to be synchronized with the instanta-
neous update signal rate. The instantaneous update signal can
To provide further protection from noise, input signals to the
voltage channel with an amplitude of <10ꢀ of full scale do not
generate zero-crossing events at all. The ZX detection circuit of
the current channels is active for all input signals, independent
of their amplitudes.
IxGAIN OR
VGAIN
REFERENCE
ADC
IA, IB, IC,
ID, IE, IF, OR V
ZX
DETECTION
PGA
HPF
LPF_ZX
39.6° OR 2.2ms @ 50Hz
1
0.855
ZX
0V
ZX
ZX
ZX
IA, IB, IC,
ID, IE, IF, OR V
LPF_ZX OUTPUT
Figure 33. Zero-Crossing Detection
Rev. 0 | Page 26 of 48
Data Sheet
ADE7816
The ADE7816 contains four zero-crossing detection circuits,
one dedicated for the voltage channel and three for the current
channels. A group of current channels (A, B, C or D, E, F) must
be selected by Bit 14 (CHANNEL_SEL) of the COMPMODE
register, Address 0xE60E (see the Selecting a Current Channel
Group section). When switching between channel groups, a set-
tling time of 10 ms (50 Hz) or 8 ms (60 Hz) is required. Each
circuit drives one flag in the STATUS1 register (Address 0xE503).
For example, if a zero crossing occurs on the voltage channel,
Bit 9 (ZXV) in the STATUS1 register goes high. If a zero-crossing
event occurs on Current Channel A and the CHANNEL_SEL
bit in the COMPMODE register is set to 0, Bit 12 (ZXI1) in the
STATUS1 register is set to 1.
Bits[4:2] (PEAKSELx) of the MMODE register (Address 0xE700)
can be set to 0 to disable a channel. Note that one PEAKSELx
bit must always be set to 1 to enable the feature.
The results of the current and voltage peak detection are stored
in the lowest 24 bits of two 32-bit, unsigned registers, IPEAK
(Address 0xE500) and VPEAK (Address 0xE501). The peak
detection measurements are updated at the end of the peak cycle
specified in the PEAKCYC register. At that time, Bit 24 (PKV)
and Bit 23 (PKI) in the STATUS1 register go high, signaling
a peak event. To determine which current channel caused the peak
event, Bits[26:24] (IPCHANNELx) in the IPEAK register must
be read.
Setting the PEAKCYC Register
Zero-Crossing Timeout
The 8-bit, unsigned PEAKCYC register contains the program-
mable peak detection period. The peak detection period is the
number of half line cycles over which the peak measurement is
measured. Each LSB of the PEAKCYC register corresponds to one
half line cycle period. The PEAKCYC register holds a maximum
value of 255.
Each zero-crossing detection circuit has an associated timeout
register. This register is loaded with the value that is written into
the 16-bit ZXTOUT register (Address 0xE60D) and is decremented
by 1 LSB every 62.5 ꢁs (16 kHz clock). The register is reset to the
ZXTOUT value every time a zero crossing is detected. The default
value of this register is 0xFFFF. If the timeout register decrements
to 0 before a zero crossing is detected, the corresponding STATUS1
bit is set.
At 50 Hz, the maximum peak cycle time is 2.55 seconds.
1
⎛
⎝
⎞
⎠
÷ 2
× 255 = 2.55 sec
⎜
⎟
50
There is a zero-crossing timeout circuit that is dedicated to the
voltage channel. For example, if a zero-crossing timeout event
occurs on the voltage channel, Bit 3 (ZXTOV) in the STATUS1
register is set. There are three zero-crossing timeout circuits for
the six current channels. A group of current channels, A, B, C or D,
E, F, must be selected by the CHANNEL_SEL bit of the
COMPMODE register (see the Selecting a Current Channel
Group section). For example, if a zero-crossing timeout event
occurs on Current Channel D and the CHANNEL_SEL bit in
the COMPMODE register is set to 1, Bit 6 (ZXTOI1) in the
STATUS1 register is set to 1.
At 60 Hz, the maximum peak cycle time is 2.125 seconds.
1
⎛
⎜
⎝
⎞
⎟
⎠
× 255 = 2.125 sec
÷ 2
60
OVERCURRENT AND OVERVOLTAGE DETECTION
The ADE7816 provides an overcurrent and overvoltage feature
that detects whether the absolute value of the current or voltage
waveform exceeds a programmable threshold. This feature uses
the instantaneous voltage and current signals. The two registers
used to set the voltage and current channel threshold are OVLVL
(Address 0xE508) and OILVL (Address 0xE507), respectively.
The OILVL threshold register determines the threshold for all
current channels. The default value of the OVLVL and OILVL
registers is 0xFFFFFF, which effectively disables the feature.
Figure 34 shows the operation of the overvoltage detection feature.
OVERVOLTAGE
The resolution of the ZXTOUT register is 62.5 ꢁs (16 kHz clock)
per LSB. Therefore, the maximum timeout period for an interrupt
is 4.096 sec (216/16 kHz).
PEAK DETECTION
The ADE7816 includes an instantaneous peak detection feature
that stores the maximum absolute value reached on the current
and voltage channels over a fixed number of half line cycles.
The PEAKCYC register (Address 0xE703) stores the number of
half line cycles used for all peak measurements.
DETECTED
VOLTAGE CHANNEL
OVLVL
The peak detection feature is available on the voltage channel
and three of the current channels. A group of current channels
(A, B, C or D, E, F) must be selected by the CHANNEL_SEL bit of
the COMPMODE register (see the Selecting a Current Channel
Group section). When switching between current channel groups,
no additional settling time is required. However, the PEAKCYC
register should be rewritten to reset the measurement. By default,
all three current channels are included in the peak detection
measurement. If only one or two current channels are required,
STATUS1[18]
CANCELLED BY A
WRITE OF STATUS1
WITH OV BIT SET.
BIT 18 (OV) OF
STATUS1
Figure 34. Overvoltage Detection
Rev. 0 | Page 27 of 48
ADE7816
Data Sheet
As shown in Figure 34, the OV bit (Bit 18) in the STATUS1 register
(Address 0xE503) is set to 1 if the ADE7816 detects an overvoltage
condition. The overcurrent detection feature works in a similar
manner; however, a group of current channels (A, B, C or D, E, F)
must be selected by Bit 14 (CHANNEL_SEL) of the COMPMODE
register, Address 0xE60E (see the Selecting a Current Channel
Group section). When switching between current channel groups,
no additional settling time is required and the feature continues to
monitor at an 8 kHz rate. If an overcurrent condition is detected on
any of the selected current channels, the OI bit (Bit 17) of the
STATUS1 register is set to 1. To determine the current channel(s)
causing the overcurrent event, the OICHANNELx bits (Bit 3, Bit 4,
and Bit 5) of the CHSTATUS register are used.
bits are unlatched and read only. A low reading (0) on any of
these bits indicates that the corresponding power reading is
positive; a high reading (1) indicates that the corresponding
power reading is negative.
In addition to the sign indication bits, the ADE7816 also includes
reverse power status bits and associated interrupts. The status bits
are located in the STATUS0 register (Address 0xE502). The reverse
power bits are set to 1 when the sign of the power changes. Bit 6
(REVAP1) monitors the A or D current channel, Bit 7 (REVAP2)
monitors the B or E channel, and Bit 8 (REVAP3) monitors the
C or F current channel. Similarly, Bit 10 (REVRP1), Bit 11
(REVRP2), and Bit 12 (REVRP3) monitor the reactive power.
Both positive-to-negative and negative-to-positive changes result
in the corresponding status bit being set. Each status bit has a cor-
responding interrupt enable bit that is located in the MASK0
register (Address 0xE50A). If the corresponding MASK0 bit is set,
Setting the OVLVL and OILVL Registers
The content of the overvoltage (OVLVL) and overcurrent (OILVL),
24-bit, unsigned registers is compared to the absolute value of
the voltage and current channels. The maximum value of these
registers is 5,928,256 (0x5A7540) with full scale inputs. When
either the OVLVL or OILVL register is equal to this value, the
overvoltage or overcurrent conditions are never detected.
Writing 0x0 to these registers signifies that the overvoltage or
overcurrent conditions are continuously detected, and the
corresponding interrupts are permanently triggered.
IRQ0
a change in active energy power direction causes the external
pin to be pulled low (see the Interrupts section for more details).
ANGLE MEASUREMENTS
The ADE7816 can measure the time delay between the current
and voltage inputs. It can also be configured to measure the time
between the six current channels. The negative-to-positive
transitions identified by the zero-crossing detection circuit are
used as a start and stop for the measurement (see Figure 35).
Overvoltage and Overcurrent Interrupts
Two interrupts are associated with the overvoltage and overcurrent
features. The first interrupt is associated with the overvoltage
feature; it is enabled by setting the OV bit (Bit 18) of the MASK1
register (Address 0xE50B). When this bit is set, an overvoltage
VOLTAGE
CURRENT
CHANNEL X
IRQ1
condition causes the external
pin to be pulled low. A second
interrupt is associated with the overcurrent detection feature.
This interrupt is enabled by setting the OI bit (Bit 17) of the
MASK1 register. When this bit is set, an overcurrent condition
on any of the selected current channels causes the external
ANGLE
Figure 35. Voltage-to-Current Time Delay
There are three angle registers that store the results of the time
delay. A group of current channels (A, B, C or D, E, F) must be
selected by Bit 14 (CHANNEL_SEL) of the COMPMODE
register (see the Selecting a Current Channel Group section).
IRQ1
pin to be pulled low.
INDICATION OF POWER DIRECTION
The ADE7816 includes sign indication on the active and reactive
power measurements. Sign indication allows positive and negative
energy to be identified and billed separately, if required. It also
helps detect a miswiring condition. This feature is available on
three channels at a time. A group of current channels (A, B, C
or D, E, F) must be selected by Bit 14 (CHANNEL_SEL) of the
COMPMODE register at Address 0xE60E (see the Selecting a
Current Channel Group section).
When Bits[10:9] (ANGLESEL) of the COMPMODE register are
set to 00b (default), the time delays between the current channels
and the voltage channel are measured. The ANGLE0 register
(Address 0xE601) stores the delay between the voltage and the
A or D current channel. The ANGLE1 register (Address 0xE602)
stores the delay between the voltage and the B or E current
channel. The ANGLE2 register (Address 0xE603) stores the delay
between the voltage and the C or F current channel. The time delay
between the current and voltage inputs can be used to characterize
how balanced the load is. The delays between phase voltages and
currents can be used to compute the power factor, as shown
in Equation 16.
The three-sign indication bits that indicate the polarity of the
active power are Bit 0 (W1SIGN), Bit 1 (W2SIGN), and Bit 2
(W3SIGN) of the CHSIGN register (Address 0xE617). W1SIGN
indicates the direction of power on the A or D current channel,
W2SIGN indicates the direction of power on the B or E current
channel, and W3SIGN indicates the direction of power on the C
or F current channel. An additional three bits, VAR1SIGN (Bit 4),
VAR2SIGN (Bit 5), and VAR3SIGN (Bit 6), also in the CHSIGN
register, provide the direction of the reactive power. All of these
360o fLINE
256 kHz
(16)
cosx cos ANGLEx
where fLINE is 50 Hz or 60 Hz.
Rev. 0 | Page 28 of 48
Data Sheet
ADE7816
This method of determining the power factor does not take into
account the effect of any harmonics.
cycles. This feature can provide an early warning signal that the
line voltage is dropping out. The voltage sag feature is controlled
by two registers: SAGCYC (Address 0xE704) and SAGLVL
(Address 0xE509). These registers control the sag period and
the sag voltage threshold, respectively.
When Bits[10:9] (ANGLESEL) of the COMPMODE register are
set to 10b, the time delays (angles) between current channels are
measured. Table 10 shows the current channel-to-channel delay
measure-ments that are available.
Sag detection is disabled by default and can be enabled by writing
a nonzero value to both the SAGCYC and SAGLVL registers. If
either register is set to 0, the sag feature is disabled. If a voltage
sag condition occurs, the sag bit (Bit 16) in the STATUS1 register
(Address 0xE503) is set to 1.
Table 10. Available Channel-to-Channel Measurements
(ANGLESEL = 10b)
Channel-to-Channel Measurements
CHANNEL_SEL
(COMPMODE[14])
0
1
ANGLE0
A to B
A to E
ANGLE1
A to C
D to F
ANGLE2
B to C
E to F
SETTING THE SAGCYC REGISTER
The 8-bit, unsigned SAGCYC register contains the programmable
sag period. The sag period is the number of half line cycles below
which the voltage channel must remain before a sag condition
occurs. Each LSB of the SAGCYC register corresponds to a half
line cycle period. The SAGCYC register holds a maximum
value of 255.
The ANGLE0 (Address 0xE601), ANGLE1 (Address 0xE602), and
ANGLE2 (Address 0xE603) registers are 16-bit, unsigned registers
with 1 LSB corresponding to 3.90625 ꢁs (256 kHz clock), which
corresponds to a resolution of 0.0703° (360° × 50 Hz/256 kHz)
for 50 Hz systems and 0.0843° (360° × 60 Hz/256 kHz) for 60 Hz
systems.
At 50 Hz, the maximum sag cycle time is 2.55 seconds.
1
⎛
⎜
⎝
⎞
⎟
⎠
× 255 = 2.55 sec
PERIOD MEASUREMENT
÷ 2
50
The ADE7816 provides the period measurement of the line in
the voltage channel. The period register (Address 0xE607) is
a 16-bit, unsigned register that updates every line period. Due
to internal filtering, a settling time of 30 ms to 40 ms is associ-
ated with this measurement.
At 60 Hz, the maximum sag cycle time is 2.125 seconds.
1
⎛
⎜
⎝
⎞
⎟
⎠
× 255 = 2.125 sec
÷ 2
60
If the SAGCYC value is modified after the feature is enabled,
the new SAGCYC period is effective immediately. Therefore, it
is possible for a sag event to be caused by a combination of sag
cycle periods. To prevent any overlap, the SAGLVL register should
be reset to 0 to effectively disable the feature before the new cycle
value is written to the SAGCYC register.
The period measurement has a resolution of 3.90625 ꢁs/LSB
(256 kHz clock), which represents 0.0195ꢀ (50 Hz/256 kHz)
when the line frequency is 50 Hz and 0.0234ꢀ (60 Hz/256 kHz)
when the line frequency is 60 Hz. The value of the period register
for 50 Hz networks is approximately 5120 (256 kHz/50 Hz) and
for 60 Hz networks is approximately 4267 (256 kHz/60 Hz). The
length of the register enables the measurement of line frequencies
that are as low as 3.9 Hz (256 kHz/216). The period register is stable
at 1 LSB when the line is established, and the measurement
does not change.
SETTING THE SAGLVL REGISTER
The content of the 24-bit SAGLVL register is compared to the
absolute value of the output from the HPF. Writing 5,928,256
(0x5A7540) to the SAGLVL register sets the sag detection level
at full scale. This results in the sag event triggering continuously.
Writing 0x00 or 0x01 puts the sag detection level at 0; therefore,
the sag event is never triggered.
The following expressions can be used to compute the line period
and frequency, using the period register:
PERIOD[15:0] +1
(17)
TL =
fL
[
sec
]
VOLTAGE SAG INTERRUPT
0x256E3
The ADE7816 includes an interrupt that is associated with the
voltage sag detection feature. If this interrupt is enabled, a voltage
sag event causes the external
is disabled by default and can be enabled by setting the sag bit
(Bit 16) in the MASK1 register, Address 0xE50B (see the
Interrupts section).
0x256E3
=
[Hz]
PERIOD[15:0] +1
IRQ1
pin to go low. This interrupt
VOLTAGE SAG DETECTION
The ADE7816 includes a sag detection feature that warns the
user when the absolute value of the line voltage falls below the
programmable threshold for a programmable number of line
Rev. 0 | Page 29 of 48
ADE7816
Data Sheet
gi, where i = 0, 1, 2, …, 31 is the coefficient of the generating
polynomial defined by the IEEE802.3 standard as follows:
CHECKSUM
The ADE7816 has a 32-bit checksum register (Address 0xE51F)
that ensures that certain important configuration registers maintain
their desired value during normal operation.
G(x) = x32 + x26 + x23 + x22 + x16 + x12 + x11 + x10
+
(18)
(19)
x8 + x7 + x5 + x4 + x2 + x + 1
g0 = g1 = g2 = g4 = g5 = g7 = 1
g8 = g10 = g11 = g12 = g16 = g22 = g26 = g31 = 1
The registers that are included in this feature are MASK0,
MASK1, COMPMODE, gain, CONFIG, MMODE, ACCMODE,
LCYCMODE, HSDC_CFG, plus four additional 16-bit reserved
registers and six 8-bit reserved internal registers. All reserved
registers always have default values. The ADE7816 computes the
cyclic redundancy check (CRC) based on the IEEE802.3 standard.
The registers are introduced, one by one, into a linear feedback
shift register (LFSR) based generator, starting with the least
significant bit (as shown in Figure 36). The 32-bit result is written
in the checksum register. After power-up or a hardware/software
reset, the CRC is computed on the default values of the registers.
The default value of the checksum register is 0x33666787.
All of the other gi coefficients are equal to 0.
FB(j) = aj − 1 XOR b31(j − 1)
(20)
(21)
b0(j) = FB(j) AND g0
bi(j) = FB(j) AND gi XOR bi − 1(j − 1), i = 1, 2, 3, ..., 31 (22)
Equation 20, Equation 21, and Equation 22 must be repeated for
j = 1, 2, …, 256. The value written into the checksum register con-
tains Bit bi(256), i = 0, 1, …, 31. After the bits from the reserved
internal register pass through the LFSR, the value of the CRC
(which is obtained at Step j = 48) is 0x33660787.
Figure 37 shows how the LFSR works. The MASK0, MASK1,
COMPMODE, gain, CONFIG, MMODE, ACCMODE,
LCYCMODE, and HSDC_CFG registers, along with the four
16-bit reserved registers and six 8-bit reserved internal registers,
form the Bits[a255, a254, …, a0] used by the LFSR. Bit a0 is the least
significant bit of the first internal register to enter the LFSR;
Bit a255 is the most significant bit of the MASK0 register, the last
register to enter the LFSR. The formulas that govern the LFSR
are as follows:
Two different approaches can be followed in using the checksum
register. One is to compute the CRC, based on Equation 18 to
Equation 22, and then compare the value against the checksum
register. Another is to periodically read the checksum register.
If two consecutive readings differ, it can be assumed that one of
the registers has changed value and that, therefore, the ADE7816
configuration has changed. The recommended response is to
initiate a hardware/software reset that sets the values of all
registers (including the reserved ones) to the default, and then
reinitialize the configuration registers.
bi(0) = 1, where i = 0, 1, 2, …, 31, the initial state of the bits that
form the CRC. Bit b0 is the least significant bit, and Bit b31 is the
most significant bit.
7
0
7
0
7
0
7
0
7
0
7
0
31
MASK0 MASK1 COMPMODE GAIN RESERVED
255 248 240 232 224 216
0
31
0
15
0 15 0 15
0
INTERNAL
REGISTER REGISTER REGISTER
INTERNAL
INTERNAL
INTERNAL
REGISTER REGISTER REGISTER
INTERNAL
INTERNAL
40 32 24
16
8
7
0
LFSR
GENERATOR
Figure 36. Checksum Register Calculation
g0
g1
g2
g3
g31
FB
b0
b1
b2
b31
LFSR
a255
,
a254,....,a2, a1, a0
Figure 37. LFSR Generator Used in Checksum Register Calculation
Rev. 0 | Page 30 of 48
Data Sheet
ADE7816
OUTPUTS
This section describes the outputs from the ADE7816.
SS
These writes allow the /HSA pin to toggle three times. See the
SPI Write Operation section for details on the write protocol
that is involved.
INTERRUPTS
IRQ0
IRQ1
and . Each pin is
The ADE7816 has two interrupt pins,
After the serial port choice is completed, it must be locked.
If I2C is the active serial port, Bit 1 (I2C_LOCK) of the CONFIG2
register (Address 0xEC01) must be set to 1 to lock it in. From then
managed by a 32-bit interrupt mask register, MASK0 and MASK1
(Address 0xE50A and Address 0xE50B), respectively. To enable
an interrupt, a bit in the MASKx register must be set to 1. To
disable an interrupt, the bit must be cleared to 0. Two 32-bit
status registers, STATUS0 and STATUS1 (Address 0xE502 and
Address 0xE503, respectively), are associated with the interrupts.
When an interrupt event occurs in the ADE7816, the corre-
sponding flag in the interrupt status register is set to a Logic 1
(see Table 30 and Table 31). If the mask bit for this interrupt in
SS
on, the ADE7816 ignores spurious toggling of the /HSA pin,
and an eventual switch to use of the SPI port is no longer possible.
If the SPI is the active serial port, any write to the CONFIG2
register locks the port. From then on, a switch to the I2C port is no
longer possible.
The functionality of the ADE7816 is accessible via several on-chip
registers. The contents of these registers can be updated or read,
using either the I2C or SPI interfaces. The HSDC port provides the
instantaneous values of the voltages and current channels.
IRQx
the interrupt mask register is Logic 1, the
logic output goes
active low. The flag bits in the interrupt status register are set,
irrespective of the state of the mask bits. To determine the source
of the interrupt, the microcontroller must perform a read of the
corresponding STATUSx register and identify which bit is set to 1.
To erase the flag in the status register, write back to the STATUSx
register with the flag set to 1. After an interrupt pin goes low, the
status register is read and the source of the interrupt is identified.
Then, the status register is written back, with no changes, to
I2C-Compatible Interface
The ADE7816 supports a fully licensed I2C interface. The I2C
interface is implemented as a full hardware slave. SDA is the data
I/O pin, and SCL is the serial clock. These two pins are shared with
the MOSI and SCLK pins, respectively, of the on-chip SPI interface.
The maximum serial clock frequency supported by this interface is
400 kHz.
IRQx
clear the status flag to 0. The
status flag is cancelled.
pin remains low until the
The SDA and SCL pins are used for data transfer and are con-
figured in a wire-AND’ed format that allows arbitration in a
multimaster system.
The transfer sequence of an I2C system consists of a master device
initiating a transfer by generating a start condition while the bus
is idle. The master transmits the address of the slave device and the
direction of the data transfer in the initial address transfer. If the
slave acknowledges, the data transfer is initiated. This continues
until the master issues a stop condition and the bus becomes idle.
By default, all interrupts are disabled, with the exception of
the RSTDONE interrupt. This interrupt can never be masked
(disabled) and, therefore, Bit 15 (RSTDONE) in the MASK1
IRQ1
register does not have any functionality. The
pin always
goes low, and Bit 15 (RSTDONE) in the STATUS1 register is set
to 1 whenever a power-up or a hardware/software reset process
ends. To cancel the RSTDONE status flag, the STATUS1 register
nust be written with Bit 15 (RSTDONE) set to 1.
COMMUNICATION
Serial Interface Selection
I2C Write Operation
The write operation, using the I2C interface of the ADE7816,
initiated when the master generates a start condition, consists
of one byte representing the address of the ADE7816, followed
by the 16-bit address of the target register and by the value of
the register.
After reset, the HSDC port is always disabled. Choose between the
2
SS
I C and SPI ports by manipulating the /HSA pin after power-up
SS
or after a hardware reset. If the /HSA pin is held high, the
ADE7816 uses the I2C port until a new hardware reset is executed.
SS
If the /HSA pin is toggled high to low three times after power-up
The most significant seven bits of the address byte constitute
the address of the ADE7816, which is 0111000b. Bit 0 of the
or after a hardware reset, the ADE7816 uses the SPI port until a
new hardware reset is executed. This manipulation of the /HSA
pin can be accomplished in two ways. The first option is to use
SS
write
address byte is a read/
bit. Because this is a write operation,
it must be cleared to 0; therefore, the first byte of the write
operation is 0x70. After every byte is received, the ADE7816
generates an acknowledge. The register can be 8, 16, or 32 bits
in length. After the last bit of the register is transmitted and the
ADE7816 acknowledges the transfer, the master generates a stop
condition. The addresses and the register content are sent with
the most significant bit first. See Figure 39 for details of the I2C
write operation.
SS
the /HSA pin of the master device (that is, the microcontroller)
as a regular I/O pin and toggle it three times. The second option is
to execute three SPI write operations to a location in the address
space that is not allocated to a specific ADE7816 register (such as
Address 0xEBFF, where 8-bit writes can be executed).
Rev. 0 | Page 31 of 48
ADE7816
Data Sheet
I2C Read Operation
SPI-Compatible Interface
The read operation, using the I2C interface of the ADE7816, is
accomplished in two stages. The first stage sets the pointer to
the address of the register; the second stage reads the contents
of the register (see Figure 40).
The ADE7816 SPI is always a slave of the communication and
consists of four pins (with dual functions): SCLK/SCL, MOSI/SDA,
SS
MISO/HSD, and /HSA. The functions used in the SPI-compatible
SS
interface are SCLK, MOSI, MISO, and . The serial clock for
a data transfer is applied at the SCLK logic input. This logic input
has a Schmitt trigger input structure that allows the use of slow
rising (and falling) clock edges. All data transfer operations
synchronize to the serial clock. Data shifts into the ADE7816
at the MOSI logic input on the falling edge of SCLK, and the
ADE7816 samples it on the rising edge of SCLK. Data shifts out
of the ADE7816 at the MISO logic output on a falling edge of SCLK
and can be sampled by the master device on the raising edge of
SCLK. The most significant bit of the word is shifted in and out
first. The maximum serial clock frequency that is supported by
this interface is 2.5 MHz. MISO stays in high impedance when no
data is transmitted from the ADE7816. Figure 38 shows details of
the connection between the ADE7816 SPI and a master device
containing a SPI interface.
The first stage is initiated when the master generates a start con-
dition. It consists of one byte, representing the address of the
ADE7816, followed by the 16-bit address of the target register. The
ADE7816 acknowledges every byte received. The address byte is
similar to the address byte of a write operation and is equal to 0x70
(see the I2C Write Operation section for details). After the last
byte of the register address is sent and acknowledged by the
ADE7816, the second stage begins with the master generating
a new start condition, followed by an address byte. The most
significant seven bits of this address byte constitute the address of
the ADE7816, which is 0111000b. Bit 0 of the address byte is a
write
read/
bit. Because this is a read operation, it must be set to 1;
therefore, the first byte of the read operation is 0x71. After this byte
is received, the ADE7816 generates an acknowledge. Then the
ADE7816 sends the value of the register, and, after every eight bits
are received, the master generates an acknowledge. All the bytes
are sent with the most significant bit first. Registers can be 8, 16,
or 32 bits. After the last bit of the register is received, the master
does not acknowledge the transfer but, instead, generates a stop
condition.
SPI DEVICE
ADE7816
MOSI/SDA
MOSI
MISO/HSD
SCLK/SCL
SS/HSA
MISO
SCK
SS
Figure 38. Connecting the ADE7816 SPI with a SPI Device
15
8
7
0
31
16
15
8
7
0
7
0
S
0
1
1
1
0
0
0
0
S
MS 8 BITS OF
REGISTER ADDRESS
LS 8 BITS OF
REGISTER ADDRESS
BYTE 3 (MS)
OF REGISTER
BYTE 0 (LS) OF
REGISTER
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
BYTE 2 OF REGISTER
BYTE 1 OF REGISTER
SLAVE ADDRESS
ACKNOWLEDGE
GENERATED BY
ADE7816
Figure 39. I2C Write Operation of a 32-Bit Register
15
8
7
0
S
0
1 1 1 0 0 0 0
A
C
K
A
C
K
A
C
K
MSB 8 BITS OF
REGISTER ADDRESS
LSB 8 BITS OF
REGISTER ADDRESS
SLAVE ADDRESS
ACKNOWLEDGE
GENERATED BY
ADE7816
ACKNOWLEDGE
GENERATED BY
MASTER
N
O
A
C
K
A
C
K
A
C
K
A
C
K
31
16
15
8
7
0
7
0
S
0
1
1
1
0
0
0
1
S
A
C
K
BYTE 3 (MSB)
OF REGISTER
BYTE 2 OF
REGISTER
BYTE 1 OF
REGISTER
BYTE 0 (LSB)
OF REGISTER
SLAVE ADDRESS
ACKNOWLEDGE
GENERATED BY
ADE7816
Figure 40. I2C Read Operation of a 32-Bit Register
Rev. 0 | Page 32 of 48
Data Sheet
ADE7816
SS
The logic input is the chip select input. This input is used
SS
when multiple devices share the serial bus. Drive the input
it begins to transmit its contents on the MISO line when the next
SCLK high-to-low transition occurs; thus, the master can sample
the data on a low-to-high SCLK transition. After the master
SS
low for the entire data transfer operation. Bringing high
SS
receives the last bit, it sets the and SCLK lines high, and the
during a data transfer operation aborts the transfer and places
the serial bus in a high impedance state. A new transfer can
communication ends. The data lines, MOSI and MISO, go into
a high impedance state (see Figure 41).
SS
then be initiated by returning the logic input to low. However,
because aborting a data transfer before completion leaves the
accessed register in a state that cannot be guaranteed, the value of a
register should be verified by reading it back each time it is written.
The protocol is similar to the protocol used with the I2C interface.
SPI Write Operation
The write operation, using the SPI interface, initiates when the
SS
master sets the /HSA pin low and begins sending one byte,
representing the address of the ADE7816, on the MOSI line. The
master sets data on the MOSI line, starting with the first high-to-
low transition of SCLK. The SPI samples data on the low-to-high
transitions of SCLK. The most significant seven bits of the address
byte can have any value, but, as a good programming practice,
SPI Read Operation
The read operation, using the SPI interface, initiates when the
SS
master sets the /HSA pin low and begins sending one byte,
representing the address of the ADE7816, on the MOSI line. The
master sets data on the MOSI line starting with the first high-to-
low transition of SCLK. The ADE7816 SPI samples data on the
low-to-high transitions of SCLK. The most significant seven bits
of the address byte can have any value, but, as good programming
they should be different from 0111000b, the seven bits that are used
2
write
in the I C protocol. Bit 0 (read/
) of the address byte must be 0
for a write operation. Next, the master sends the 16-bit address
of the register that is written and the 32-, 16-, or 8-bit value of that
register without losing any SCLK cycle. After the last bit is trans-
mitted, the master sets the and SCLK lines high at the end of
the SCLK cycle and the communication ends. The data lines, MOSI
and MISO, go into a high impedance state (see Figure 42).
practice, they should be different from 0111000b, the seven bits
2
SS
write
used in the I C protocol. Bit 0 (read/
) of the address byte must
be set to 1 for a read operation. Next, the master sends the 16-bit
address of the register to be read. After the ADE7816 receives the
last address bit of the register on a low-to-high transition of SCLK,
SS
SCLK
15 14
1 0
MOSI
MISO
REGISTER ADDRESS
0
0 0 0 0 0 0 1
31 30
1 0
REGISTER VALUE
Figure 41. SPI Read Operation of a 32-Bit Register
SS
SCLK
15 14
1
0
31 30
1 0
REGISTER
ADDRESS
MOSI
REGISTER VALUE
0
0 0 0 0 0 0 0
Figure 42. SPI Write Operation of a 32-Bit Register
Rev. 0 | Page 33 of 48
ADE7816
Data Sheet
The words can be transmitted as 32-bit or 8-bit packages. When
Bit 1 (HSIZE) in the HSDC_CFG register is 0 (the default value),
the words are transmitted as 32-bit packages. When Bit HSIZE is 1,
the registers are transmitted as 8-bit packages. The HSDC interface
transmits the words MSB first.
HSDC Interface
The high speed data capture (HSDC) interface is disabled by
default. It can be used only if the ADE7816 is configured with
an I2C interface. The ADE7816 SPI interface cannot be used
simultaneously with the HSDC port.
When Bit 2 (HGAP) is set to 1, a gap of seven HSCLK cycles is
introduced between packages. When the HGAP bit is cleared to 0
(the default value), no gap is introduced between packages and
the communication time is shortest. In this case, HSIZE does
not have any influence on the communication, and a data bit is
placed on the HSD line with every HSCLK high-to-low transition.
Bit 6 (HSDCEN) in the CONFIG register (Address 0xE618)
activates HSDC when set to 1. If the HSDCEN bit is cleared to 0,
the default value, the HSDC interface is disabled. Setting the
HSDCEN bit to 1 when the SPI is in use does not have any effect.
The HSDC port is an interface for sending up to four 32-bit
words to an external device (usually a microprocessor or a DSP).
The words represent the instantaneous values of the currents and
voltage. The registers that are transmitted are IAWV/IDWV,
I BW V / I EW V, IC W V / I F W V, a n d V W V. A l l a r e 2 4 - b i t r e g i s t e r s
that are sign extended to 32 bits.
For correct operation, Bits[4:3] (HXFER[1:0]) must be set to a
value of 01b. The words representing the instantaneous values
of currents and voltage are transmitted in the following order:
IAW V / I DW V, V W V, I BW V / I EW V, V W V, IC V W / I F W V, a n d
VWV, followed by one 32-bit word of all 0s. Note that the voltage
waveform is sent three times. Bit 14 (CHANNEL_SEL) of the
COMPMODE register (Address 0xE60E) can be used to select
which group of current channels is transmitted (see the
Selecting a Current Channel Group section).
The HSDC port can be interfaced with the SPI or similar interfaces.
HSDC is always a master of the communication and consists of
three pins: HSA, HSD, and HSCLK. HSA represents the select
signal. It stays active low or high when a word is transmitted,
and it is usually connected to the select pin of the slave. HSD
sends data to the slave, and it is usually connected to the data
input pin of the slave. HSCLK is the serial clock line that is
generated by the ADE7816, and it is usually connected to the
serial clock input of the slave. Figure 43 shows the connections
between the ADE7816 HSDC and slave devices containing a SPI
interface.
Bit 5 (HSAPOL) of the HSDC_CFG register determines the
SS
HSA function polarity of the /HSA pin during communication.
When the HSAPOL bit is 0 (the default value), HSA is active low
during the communication. This means that HSA stays high
when no communication is in progress. When the communication
starts, HSA goes low and stays low until the communication ends.
Then it goes back to high. When HSAPOL is 1, the HSA function
SS
SPI DEVICE
ADE7816
of the /HSA pin is active high during the communication.
This means that HSA stays low when no communication is in
progress. When the communication starts, HSA goes high and
stays high until the communication ends; then it goes back to low.
MISO/HSD
HSCLK
MISO
SCK
SS
SS/HSA
Figure 43. Connecting the ADE7816 HSDC with a SPI
Bits[7:6] of the HSDC_CFG register are reserved. Any value
written into these bits has no consequence on HSDC behavior.
The HSDC communication is managed by the HSDC_CFG
register, Address 0xE706 (see Table 28). It is recommended that
the HSDC_CFG register be set to the desired value before enabling
the port, using Bit 6 (HSDCEN) in the CONFIG register. In this
way, the state of various pins belonging to the HSDC port do not
take levels that are inconsistent with the desired HSDC behavior.
Figure 44 shows the HSDC transfer protocol for HGAP = 0,
HXFER[1:0] = 01, and HSAPOL = 0. Note that the HSDC
interface sets a data bit on the HSD line every HSCLK high-
to-low transition, and the value of Bit HSIZE is irrelevant.
Figure 45 shows the HSDC transfer protocol for HSIZE = 0,
HGAP = 1, HXFER[1:0] = 01, and HSAPOL = 0. Note that the
HSDC interface introduces a gap of seven HSCLK cycles between
every 32-bit word.
SS
After a hardware reset or power-up, the MISO/HSD and /HSA
pins are set high.
Bit 0 (HCLK) in the HSDC_CFG register determines the serial
clock frequency of the HSDC communication. When HCLK is 0
(the default value), the clock frequency is 8 MHz. When HCLK is 1,
the clock frequency is 4 MHz. A bit of data is transmitted for every
HSCLK high-to-low transition. The slave device that receives data
from HSDC samples the HSD line on the low-to-high transition
of HSCLK.
Figure 46 shows the HSDC transfer protocol for HSIZE = 1,
HGAP = 1, HXFER[1:0] = 01, and HSAPOL = 0. Note that the
HSDC interface introduces a gap of seven HSCLK cycles between
every 8-bit word.
See Table 28 for the HSDC_CFG register and descriptions for
the HCLK, HSIZE, HGAP, HXFER[1:0], and HSAPOL bits.
Rev. 0 | Page 34 of 48
Data Sheet
ADE7816
Table 11 lists the time that is required to execute an HSDC data transfer for all HSDC_CFG register settings.
Table 11. Communication Times for Various HSDC Settings
HXFER[1:0]
HGAP
HSIZE1
HCLK
Communication Time (μs)
01
01
01
01
01
01
0
0
1
1
1
1
N/A
N/A
0
0
1
0
1
0
1
0
1
28
56
33.25
66.5
51.625
103.25
1
1 N/A means not applicable.
HSCLK
31
0
31
0
31
0
31
0
HSD
HSA
IAWV/IDWV (32)
VWV (32)
IBWV/IEWV (32)
0000000 (32)
Figure 44. HSDC Communication for HGAP = 0, HXFER[1:0] = 01, and HSAPOL = 0; HSIZE Is Irrelevant
HSCLK
HSD
31
0
31
0
31
0
31
00000000 (32)
0
IAWV/IDWV (32)
VWV (32)
IBWV/IEWV (32)
7 HSCLK CYCLES
7 HSCLK CYCLES
HSA
Figure 45. HSDC Communication for HSIZE = 0, HGAP = 1, HXFER[1:0] = 01, and HSAPOL = 0
HSCLK
31
24
23
16
15
8
7
0
IAWV/IDWV (BYTE 3)
IAWV/IDWV (BYTE 2)
IAWV/IDWV (BYTE 1)
00 (BYTE 0)
HSD
HSA
7 HSCLK CYCLES
7 HSCLK CYCLES
Figure 46. HSDC Communication for HSIZE = 1, HGAP = 1, HXFER[1:0] = 01, and HSAPOL = 0
Rev. 0 | Page 35 of 48
ADE7816
Data Sheet
REGISTERS
REGISTER PROTECTION
REGISTER FORMAT
The ADE7816 includes 8-, 16-, and 32-bit, signed and unsigned
registers. All signed registers are in twos complement format.
Some of the internal measurements are 24 bits long and have
been extended to 32 bits prior to communication. This extension
is accomplished in three different ways: sign extending (SE), zero
padding (ZP), or zero padded and sign extended (ZPSE). When
sign extending is used, the sign bit (Bit 23) of the twos complement
signed number is duplicated in the uppermost byte prior to
communication. Zero padding is achieved by writing 0s into the
upper most byte prior to transmission. This format is used for
unsigned numbers only. Zero padded and sign extended formats
are shown in Figure 47 and involve padding the most significant
bits with 0s and sign extending Bits[27:24].
To protect the integrity of the data stored in the data memory
(located at Address 0x4380 to Address 0x43BE), a write protection
mechanism is available. By default, the protection is disabled,
and registers that are located between Address 0x4380 and
Address 0x43BE can be written without restriction. When the
protection is enabled, no writes to these registers are allowed.
Registers can always be read, without restriction, independent
of the write protection state.
To enable the protection, write 0xAD to an internal 8-bit
register that is located at Address 0xE7FE, followed by a write
of 0x80 to an internal 8-bit register located at Address 0xE7E3.
It is recommended that the write protection be enabled before
starting the DSP. If any register requires changing after this time,
disable the protection, change the value, and then reenable the
protection. There is no need to stop the DSP to change these
registers.
31
28 27
24 23
0
0000
24-BIT NUMBER
BITS[27:24] ARE
EQUAL TO BIT 23
BIT 23 IS A SIGN BIT
To disable the protection, write 0xAD to an internal 8-bit
register that is located at Address 0xE7FE, followed by a write of
0x00 to an internal 8-bit register that is located at Address 0xE7E3.
Figure 47. ZPSE Communication Format
The communication format of each register is specified in the
Register Maps section (see Table 12 through Table 15).
Rev. 0 | Page 36 of 48
Data Sheet
ADE7816
REGISTER MAPS
Table 12. Calibration and Power Quality Registers
Register
Name
Bit
Bit Length During
Default
Value
Address
0x4380
0x4381
0x4382
0x4383
0x4384
0x4385
0x4386
0x4387
0x4388
R/W1
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Length Communication2 Type 3
Description
VGAIN
24
24
24
24
24
24
24
24
24
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
S
S
S
S
S
S
S
S
S
0x000000 Voltage gain adjustment.
IAGAIN
IBGAIN
ICGAIN
IDGAIN
IEGAIN
IFGAIN
Reserved
DICOEFF
0x000000 Current Channel A current gain adjustment.
0x000000 Current Channel B current gain adjustment.
0x000000 Current Channel C current gain adjustment.
0x000000 Current Channel D current gain adjustment.
0x000000 Current Channel E current gain adjustment.
0x000000 Current Channel F current gain adjustment.
0x000000 This register should be ignored.
0x000000 Register used in the digital integrator algorithm.
When the integrator is enabled, this register
should be set to 0xFFF8000.
0x4389
0x438A
0x438B
0x438C
0x438D
0x438E
0x438F
0x4390
0x4391
0x4392
0x4393
0x4394
0x4395
0x4396
0x4397
0x4398
0x4399
0x439A
0x439B
0x439C
0x439D
0x439E
0x439F
0x43A0
0x43A1
0x43A2
0x43A3
0x43A4
0x43A5
0x43A6
0x43A7
0x43A8
0x43A9
0x43AA
0x43AB
HPFDIS
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
0x000000 Disables the high-pass filter for all channels.
0x000000 Voltage rms offset.
VRMSOS
IARMSOS
IBRMSOS
ICRMSOS
IDRMSOS
IERMSOS
IFRMSOS
AWGAIN
AWATTOS
BWGAIN
BWATTOS
CWGAIN
CWATTOS
DWGAIN
DWATTOS
EWGAIN
EWATTOS
FWGAIN
FWATTOS
AVARGAIN
AVAROS
BVARGAIN
BVAROS
CVARGAIN
CVAROS
DVARGAIN
DVAROS
EVARGAIN
EVAROS
FVARGAIN
FVAROS
0x000000 Current Channel A current rms offset.
0x000000 Current Channel B current rms offset.
0x000000 Current Channel C current rms offset.
0x000000 Current Channel D current rms offset.
0x000000 Current Channel E current rms offset.
0x000000 Current Channel F current rms offset.
0x000000 Channel A active power gain adjust.
0x000000 Channel A active power offset adjust.
0x000000 Channel B active power gain adjust.
0x000000 Channel B active power offset adjust.
0x000000 Channel C active power gain adjust.
0x000000 Channel C active power offset adjust.
0x000000 Channel D active power gain adjust
0x000000 Channel D active power offset adjust.
0x000000 Channel E active power gain adjust.
0x000000 Channel E active power offset adjust.
0x000000 Channel F active power gain adjust.
0x000000 Channel F active power offset adjust.
0x000000 Channel A reactive power gain adjust.
0x000000 Channel A reactive power offset adjust.
0x000000 Channel B reactive power gain adjust.
0x000000 Channel B reactive power offset adjust.
0x000000 Channel C reactive power gain adjust.
0x000000 Channel C reactive power offset adjust.
0x000000 Channel D reactive power gain adjust.
0x000000 Channel D reactive power offset adjust.
0x000000 Channel E reactive power gain adjust.
0x000000 Channel E reactive power offset adjust.
0x000000 Channel F reactive power gain adjust.
0x000000 Channel F reactive power offset adjust.
This register should be ignored.
Reserved
Reserved
WTHR1
This register should be ignored.
0x000000 Most significant 24 bits of the WTHR[47:0]
threshold.
0x000000 Least significant 24 bits of the WTHR[47:0]
threshold.
R/W
R/W
24
24
32 ZP
32 ZP
U
U
0x43AC
WTHR0
Rev. 0 | Page 37 of 48
ADE7816
Data Sheet
Register
Name
Bit
Bit Length During
Default
Value
Address
R/W1
Length Communication2 Type 3
Description
0x43AD
VARTHR1
R/W
24
24
32 ZP
32 ZP
U
U
0x000000 Most significant 24 bits of the VARTHR[47:0]
threshold.
0x000000 Least significant 24 bits of the VARTHR[47:0]
threshold.
0x43AE
VARTHR0
R/W
0x43AF
0x43B0
APNOLOAD
VARNOLOAD
RW
R/W
24
24
32 ZP
32 ZPSE
U
S
0x000000 No load threshold in the active power datapath.
0x000000 No load threshold in the reactive power
datapath.
0x43B1
0x43B2
0x43B3
0x43B4
0x43B5
0x43B6
PCF_A_COEFF
PCF_B_COEFF
PCF_C_COEFF
R/W
R/W
R/W
24
24
24
24
24
24
N/A
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
32 ZPSE
N/A
U
0x000000 Phase calibration coefficient for Channel A. Set
to 0x400C4A for a 50 Hz system and 0x401235
for a 60 Hz system.
0x000000 Phase calibration coefficient for Channel B. Set
to 0x400C4A for a 50 Hz system and 0x401235
for a 60 Hz system.
0x000000 Phase calibration coefficient for Channel C. Set
to 0x400C4A for a 50 Hz system and 0x401235
for a 60 Hz system.
0x000000 Phase calibration coefficient for Channel D. Set
to 0x400C4A for a 50 Hz system and 0x401235
for a 60 Hz system.
0x000000 Phase calibration coefficient for Channel E. Set to
0x400C4A for a 50 Hz system and 0x401235 for
a 60 Hz system.
0x000000 Phase calibration coefficient for Channel F. Set to
0x400C4A for a 50 Hz system and 0x401235 for
a 60 Hz system.
U
U
PCF_D_COEFF R/W
U
PCF_E_COEFF
PCF_F_COEFF
Reserved
R/W
R/W
N/A
U
U
0x43B7
to
N/A
0x000000 These registers should be ignored.
0x43BF
0x43C0
0x43C1
0x43C2
0x43C3
0x43C4
0x43C5
0x43C6
VRMS
R
R
R
R
R
R
R
24
24
24
24
24
24
24
32 ZP
32 ZP
32 ZP
32 ZP
32 ZP
32 ZP
32 ZP
S
S
S
S
S
S
S
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Voltage rms value.
IARMS
IBRMS
ICRMS
IDRMS
IERMS
IFRMS
Reserved
Current Channel A current rms value.
Current Channel B current rms value.
Current Channel C current rms value.
Current Channel D current rms value.
Current Channel E current rms value.
Current Channel F current rms value.
These registers should be ignored.
0x43C7
to 0x43FF
1 R is read, and W is write.
2 For more information, see the Register Format section.
3 U indicates an unsigned register, and S indicates a signed register in twos complement format.
Table 13. Run Register
Register
Name
Bit
Length Communication
16 16
Bit Length During
Default
Value
Address
R/W1
Type2
Description
0xE228
Run
R/W
U
0x0000
This register starts and stops the DSP.
1 R is read, and W is write.
2 U indicates an unsigned register.
Rev. 0 | Page 38 of 48
Data Sheet
ADE7816
Table 14. Billable Registers
Register
Name
Bit
Length
Bit Length During
Communication
Default
Value
Address
0xE400
0xE401
0xE402
0xE403
0xE404
0xE405
0xE406
0xE407
0xE408
0xE409
0xE40A
0xE40B
R/W1
R
R
R
R
R
R
R
R
R
R
R
Type 2
Description
AWATTHR
BWATTHR
CWATTHR
DWATTHR
EWATTHR
FWATTHR
AVARHR
BVARHR
CVARHR
DVARHR
EVARHR
FVARHR
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
S
S
S
S
S
S
S
S
S
S
S
S
0x00000000 Channel A active energy accumulation.
0x00000000 Channel B active energy accumulation.
0x00000000 Channel C active energy accumulation.
0x00000000 Channel D active energy accumulation.
0x00000000 Channel E active energy accumulation.
0x00000000 Channel F active energy accumulation.
0x00000000 Channel A reactive energy accumulation.
0x00000000 Channel B reactive energy accumulation.
0x00000000 Channel C reactive energy accumulation.
0x00000000 Channel D reactive energy accumulation.
0x00000000 Channel E reactive energy accumulation.
0x00000000 Channel F reactive energy accumulation.
R
1 R is read, and W is write.
2 S indicates a signed register in twos complement format.
Table 15. Configuration and Power Quality Registers
Register
Name
Bit
Length
Bit Length During
Default
Address
0xE500
0xE501
0xE502
0xE503
0xE504
0xE505
0xE506
0xE507
0xE508
0xE509
0xE50A
0xE50B
0xE50C
R/W1
R
Communication2 Type3
Value4
N/A
Description
IPEAK
VPEAK
32
32
32
32
20
20
20
24
24
24
32
32
24
32
32
32
32
32 ZP
32 ZP
32 ZP
32 ZP
32 ZP
32 ZP
32
U
U
U
U
U
U
U
U
U
U
U
U
S
Current peak register.
Voltage peak register.
R
N/A
N/A
N/A
N/A
N/A
N/A
0xFFFFFF
0xFFFFFF
0x000000
STATUS0
STATUS1
Reserved
Reserved
Reserved
OILVL
OVLVL
SAGLVL
MASK0
R/W
R/W
R
R
R
R/W
R/W
R/W
R/W
R/W
R
Interrupt Status Register 0.
Interrupt Status Register 1.
This register should be ignored.
This register should be ignored.
This register should be ignored.
Overcurrent threshold.
Overvoltage threshold.
Voltage sag level threshold.
0x00000000 Interrupt Enable Register 0.
0x00000000 Interrupt Enable Register 1.
N/A
N/A
N/A
MASK1
IAWV/IDWV
32
32 SE
Instantaneous Current Channel A and
Instantaneous Current Channel D.
Instantaneous Current Channel B and
Instantaneous Current Channel E.
Instantaneous Current Channel C and
Instantaneous Current Channel F.
0xE50D
0xE50E
IBWV/IEWV
ICWV/IFWV
R
R
24
24
32 SE
32 SE
S
S
0xE50F
0xE510
0xE511 to
0xE51E
Reserved
VWV
Reserved
R
R
R
24
24
24
32 SE
32 SE
32 SE
S
S
S
N/A
N/A
N/A
This register should be ignored.
Instantaneous voltage.
This register should be ignored.
0xE51F
Checksum
Reserved
R
32
32
U
0x33666787 Checksum verification (see the Checksum
section for details).
0xE520 to
0xE52E
These registers should be ignored.
0xE600
0xE601
CHSTATUS
ANGLE0
R
R
16
16
16
16
U
U
N/A
N/A
Channel peak register.
Time Delay 0 (see the Angle
Measurements section for details).
0xE602
0xE603
ANGLE1
ANGLE2
Reserved
R
R
16
16
16
16
U
U
N/A
N/A
Time Delay 1 (see the Angle
Measurements section for details).
Time Delay 2 (see the Angle
Measurements section for details).
0xE604 to
0xE606
These registers should be ignored.
Rev. 0 | Page 39 of 48
ADE7816
Data Sheet
Register
Name
Bit
Length
Bit Length During
Default
Value4
Address
0xE607
0xE608
0xE609 to
0xE60B
R/W1
Communication2 Type3
Description
Period
CHNOLOAD
Reserved
R
R
16
16
16
16
U
U
N/A
N/A
Line period.
Channel no load register.
For proper operation, do not write to
these addresses.
0xE60C
0xE60D
0xE60E
0xE60F
0xE610 to
0xE616
LINECYC
ZXTOUT
COMPMODE R/W
Gain
Reserved
R/W
R/W
16
16
16
16
16
16
16
16
U
U
U
U
0xFFFF
0xFFFF
0x01FF
0x0000
Line cycle accumulation mode count.
Zero-crossing timeout count.
Computation mode register.
PGA gains at ADC inputs (see Table 22).
This register should be ignored.
R/W
0xE617
0xE618
0xE700
0xE701
0xE702
0xE703
0xE704
0xE705
0xE706
0xE707
0xE7E3
CHSIGN
CONFIG
R
16
16
8
8
8
16
16
8
8
8
U
U
U
U
U
U
U
N/A
Power sign register.
Configuration register.
R/W
R/W
R/W
R/W
R/W
R/W
0x0000
0x1C
0x00
0x78
0x00
0x00
MMODE
ACCMODE
LCYCMODE
PEAKCYC
SAGCYC
Reserved
HSDC_CFG
Version
Measurement mode register.
Accumulation mode register.
Line accumulation mode.
Peak detection half line cycles.
Sag detection half line cycles.
This register should be ignored.
HSDC configuration register.
Version of die.
8
8
8
8
R/W
R/W
R/W
8
8
8
8
8
8
U
U
U
0x00
0x00
Reserved
Register protection (see the Register
Protection section).
0xE7FE
0xEBFF
Reserved
Reserved
Register protection key (see the Register
Protection section).
This address can be used in manipulating
the SS/HSA pin when SPI is chosen as
the active port (see the Communication
section for details).
8
8
8
8
0xEC00
0xEC01
Reserved
CONFIG2
This register should be ignored.
Configuration register (see Table 29).
R/W
U
0x00
1 R is read, and W is write.
2 32 ZP is a 24- or 20-bit, signed or unsigned register that is transmitted as a 32-bit word with 8 or 12 MSBs, respectively, padded with 0s. 32 SE is a 24-bit, signed register
that is transmitted as a 32-bit word that is sign extended to 32 bits.
3 U indicates an unsigned register, and S indicates a signed register in twos complement format.
4 N/A is not applicable.
REGISTER DESCRIPTIONS
Table 16. HPFDIS Register (Address 0x4389)
Bits
Default Value
Description
[23:0]
0x000000
When HPFDIS = 0x000000, all high-pass filters in voltage and current channels are enabled.
When the register is set to any nonzero value, all high-pass filters are disabled.
Table 17. IPEAK Register (Address 0xE500)
Bits
[31:27]
26
25
24
Bit Name
Default Value Description
Reserved
0x00000
0x0
These bits should be ignored.
IPCHANNEL2
IPCHANNEL1
IPCHANNEL0
IPEAKVAL[23:0]
The C or F current channel generated the IPEAKVAL[23:0] value.
The B or E current channel generated the IPEAKVAL[23:0] value.
The A or D current channel generated the IPEAKVAL[23:0] value.
Current channel peak value
0x0
0x0
0x0
[23:0]
Table 18. VPEAK Register (Address 0xE501)
Bits
Bit Name
Default Value Description
[31:24]
[23:0]
Reserved
VPEAKVAL[23:0]
0x00000
0x0
These bits should be ignored.
Voltage channel peak value.
Rev. 0 | Page 40 of 48
Data Sheet
ADE7816
Note that Address 0xE502, Address 0xE503, Address 0xE50A, and Address 0xE50B are listed in Table 30 and Table 31.
Table 19. CHSTATUS Register (Address 0xE600)
Default
Bits
[15:6]
5
4
3
Bit Name
Value
0x000
0x0
0x0
0x0
Description
Reserved
These bits should be ignored.
OICHANNEL2
OICHANNEL1
OICHANNEL0
Reserved
The C or F current channel generated the overcurrent event.
The B or E current channel generated the overcurrent event.
The A or D current channel generated the overcurrent event.
Reserved. These bits are always 0.
[2:0]
0x000
Table 20. CHNOLOAD Register (Address 0xE608)
Default
Value
Bits
[15:6]
5
Bit Name
Reserved
NOLOADF
Description
0x0000000 These bits should be ignored.
0x0
0x0
0x0
0x0
0x0
0x0
0: Channel F is out of the no load condition.
1: Channel F is in the no load condition.
0: Channel E is out of the no load condition.
1: Channel E is in the no load condition.
0: Channel D is out of the no load condition.
1: Channel D is in the no load condition.
0: Channel C is out of the no load condition.
1: Channel C is in the no load condition.
0: Channel B is out of the no load condition.
1: Channel B is in the no load condition.
0: Channel A is out of the no load condition.
1: Channel A is in the no load condition.
4
3
2
1
0
NOLOADE
NOLOADD
NOLOADC
NOLOADB
NOLOADA
Table 21. COMPMODE Register (Address 0xE60E)
Default
Value
Bits
15
Bit Name
Description
Reserved
0x0
This bit should be ignored.
14
CHANNEL_SEL
0x0
0: the A, B, and C current channels are used for the peak, overcurrent, zero crossing, angle, and
waveform measurements.
1: the D, E, and F current channels are used for the peak, overcurrent, zero crossing, angle, and
waveform measurements.
[13:11] Reserved
0x0
These bits should be ignored.
[10:9]
ANGLESEL
0x00
00: the time delays between the voltage and currents are measured.
01: reserved.
10: the angles between current channels are measured.
11: no angles are measured.
[8:0]
Reserved
0x1FF
These bits should be ignored and not modified.
Table 22. Gain Register (Address 0xE60F)
Default
Value
Bits
Bit Name
Reserved
PGA3[2:0]
Description
[15:9]
[8:6]
0x0000000 These bits should be ignored.
0x000 Gain selection for the D, E, and F current channels.
000: gain = 1.
001: gain = 2.
010: gain = 4.
011: gain = 8.
100: gain = 16.
101, 110, 111: reserved.
Rev. 0| Page 41 of 48
ADE7816
Data Sheet
Default
Value
Bits
Bit Name
Description
[5:3]
PGA2[2:0]
0x000
Voltage channel gain selection.
000: gain = 1
001: gain = 2.
010: gain = 4.
011: gain = 8.
100: gain = 16.
101, 110, 111: reserved.
Gain selection for the A, B, and C current channels.
000: gain = 1.
[2:0]
PGA1[2:0]
0x000
001: gain = 2.
010: gain = 4.
011: gain = 8.
100: gain = 16.
101, 110, 111: reserved.
Table 23. CHSIGN Register (Address 0xE617)
Default
Value
Bits
[15:7]
6
Bit Name
Reserved
VAR3SIGN
Description
0x0000000 These bits should be ignored.
0x0
0x0
0x0
0: the reactive power on the C or F channel is positive.
1: the reactive power on the C or F channel is negative.
0: the reactive power on the B or E channel is positive.
1: the reactive power on the B or E channel is negative.
0: the reactive power on the A or D channel is positive.
1: the reactive power on the A or D channel is negative.
This bit should be ignored.
5
4
VAR2SIGN
VAR1SIGN
3
2
Reserved
W3SIGN
0x0
0x0
0: the active power on the C or F channel is positive.
1: the active power on the C or F channel is negative.
0: the active power on the B or E channel is positive.
1: the active power on the B or E channel is negative.
0: the active power on the A or D channel is positive.
1: the active power on the A or D channel is negative.
1
0
W2SIGN
W1SIGN
0x0
0x0
Table 24. CONFIG Register (Address 0xE618)
Default
Value
Bits
[15:8]
7
Bit Name
Reserved
SWRST
Description
0x0
These bits should be ignored.
Initiates a software reset.
Enables the HSDC serial port.
These bits should be ignored.
Enables the digital integrator.
0x0
6
HSDCEN
Reserved
INTEN
0x0
[5:1]
0
0x0
0x0
Table 25. MMODE Register (Address 0xE700)
Default
Bits
[7:5]
4
Bit Name
Reserved
PEAKSEL2
PEAKSEL1
PEAKSEL0
Reserved
Value
0x000
0x1
Description
These bits should be ignored.
The C or F current channel is selected for peak detection.
The B or E current channel is selected for peak detection.
The A or D current channel is selected for peak detection.
These bits should be ignored.
3
0x1
2
0x1
[1:0]
0x00
Rev. 0 | Page 42 of 48
Data Sheet
ADE7816
Table 26. ACCMODE Register (Address 0xE701)
Default
Value
Bits
Bit Name
Description
7
REVRPSEL
0x0
0: the sign of the reactive power is monitored on the A, B, and C channels.
1: the sign of the reactive power is monitored on the D, E, and F channels.
6
REVAPSEL
0x0
0: the sign of the active power is monitored on the A, B, and C channels.
1: the sign of the active power is monitored on the D, E, and F channels.
[5:4]
[3:2]
Reserved
0x00
0x00
These bits should be ignored and not modified.
VARACC[1:0]
00: signed accumulation for all reactive power measurements.
01: reserved.
10: reserved.
11: reserved.
[1:0]
WATTACC[1:0]
0x00
00: signed accumulation for all active power measurements.
01: reserved.
10: reserved.
11: reserved.
Table 27. LCYCMODE Register (Address 0xE702)
Default
Value
Bits
7
Bit Name
Reserved
RSTREAD
Description
0x0
Reserved. This bit does not control any functionality.
6
0x1
Enables read-with-reset for all energy registers. Note that this bit has no function in line cycle
accumulation mode and should be set to 0 when this mode is in use.
[5:4]
Reserved
ZX_SEL
Reserved
LVAR
0x0
0x0
0x0
0x0
0x0
These bits should be ignored.
3
2
1
0
Enables the voltage channel zero-crossing counter for line cycle accumulation mode.
These bits should be ignored.
Enables the reactive energy line cycle accumulation mode.
Enables the active energy line cycle accumulation mode.
LWATT
Table 28. HSDC_CFG Register (Address 0xE706)
Default
Bits
[7:6]
5
Bit Name
Reserved
HSAPOL
Value
0x00
0x0
Description
These bits should be ignored.
0: SS/HSA output pin is active low (default).
1: SS/HSA output pin is active high.
[4:3]
HXFER[1:0]
0x00
00 = reserved.
01 = HSDC transmits current and voltage waveform data.
10 = reserved.
11 = reserved.
2
1
0
HGAP
HSIZE
HCLK
0x0
0x0
0x0
0: no gap is introduced between packages (default).
1: a gap of seven HCLK cycles is introduced between packages.
0: HSDC transmits the 32-bit registers in 32-bit packages, most significant bit first (default).
1: HSDC transmits the 32-bit registers in 8-bit packages, most significant bit first.
0: HSCLK = 8 MHz (default).
1: HSCLK = 4 MHz.
Table 29. CONFIG2 Register (Address 0xEC01)
Default
Value
Bits
[7:2]
1
Bit Name
Reserved
I2C_LOCK
EXTREFEN
Description
0x0
These bits should be ignored.
Serial port lock.
0x0
0
0x0
Set to 1 to use with an external reference.
Rev. 0| Page 43 of 48
ADE7816
Data Sheet
Interrupt Enable and Interrupt Status Registers
Table 30. STATUS0 Register (Address 0xE502) and MASK0 Register (Address 0xE50A)
Bits
Bit Name Default Value
Description
[31:18] Reserved
0 0000 0000 0000
These bits should be ignored.
17
16
15
14
13
12
11
10
9
DREADY
Reserved
Reserved
Reserved
Reserved
REVRP3
REVRP2
REVRP1
Reserved
REVAP3
REVAP2
REVAP1
LENERGY
Reserved
REHF2
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
New waveform data is ready.
This bit should be ignored.
This bit should be ignored.
This bit should be ignored.
This bit should be ignored.
The sign of the reactive power has changed (C or F channel).
The sign of the reactive power has changed (B or E channel).
The sign of the reactive power has changed (A or D channel).
This bit should be ignored.
8
The sign of the active power has changed (C or F channel).
The sign of the active power has changed (B or E channel).
The sign of the active power has changed (A or D channel).
The end of a line cycle accumulation period.
This bit should be ignored.
7
6
5
4
3
The active energy register is half full (D, E, or F channel).
The reactive energy register is half full (A, B, or C channel).
The active energy register is half full (D, E, or F channel)
The active energy register is half full (A, B, or C channel).
2
REHF1
1
AEHF2
0
AEHF1
Table 31. STATUS1 Register (Address 0xE503) and MASK1 Register (Address 0xE50B)
Bits
Bit Name Default Value
Description
[31:25] Reserved
0x0000000
0x0
These bits should be ignored.
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
PKV
The end of the voltage channel peak detection period.
The end of the current channel peak detection period.
This bit should be ignored.
PKI
0x0
Reserved
Reserved
Reserved
Reserved
OV
0x0
0x1
This bit should be ignored.
0x0
This bit should be ignored.
0x0
This bit should be ignored.
0x0
An overvoltage event has occurred.
An overcurrent event has occurred.
A sag event has occurred.
OI
0x0
Sag
0x0
RSTDONE 0x1
The end of a software or hardware reset.
C or F current channel zero crossing.
B or E current channel zero crossing.
A or D current channel zero crossing.
This bit should be ignored.
ZXI3
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
0x0
ZXI2
ZXI1
Reserved
Reserved
ZXV
This bit should be ignored.
Voltage channel zero crossing.
8
ZXTOI3
ZXTOI2
ZXTOI1
Reserved
Reserved
ZXTOV
Reserved
NLOAD2
NLOAD1
A zero crossing on the C or F current channel is missing.
A zero crossing on the B or E current channel is missing.
A zero crossing on the A or D current channel is missing.
This bit should be ignored.
7
6
5
4
This bit should be ignored.
3
A zero crossing on the voltage channel is missing.
This bit should be ignored.
2
1
Active and reactive no load condition on the D, E, or F current channel.
Active and reactive no load condition on the A, B, or C current channel.
0
Rev. 0 | Page 44 of 48
Data Sheet
ADE7816
OUTLINE DIMENSIONS
6.10
6.00 SQ
5.90
0.30
0.23
0.18
PIN 1
INDICATOR
PIN 1
INDICATOR
31
30
40
1
0.50
BSC
4.45
4.30 SQ
4.25
EXPOSED
PAD
21
20
10
11
0.45
0.40
0.35
0.25 MIN
TOP VIEW
BOTTOM VIEW
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
0.80
0.75
0.70
0.05 MAX
0.02 NOM
SECTION OF THIS DATA SHEET.
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-220-WJJD.
Figure 48. 40-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
6 mm × 6 mm Body, Very Very Thin Quad
(CP-40-10)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
Temperature Range
Package Description
40-Lead LFCSP_WQ
40-Lead LFCSP_WQ
Evaluation Board
Package Option
ADE7816ACPZ
ADE7816ACPZ-RL
EVAL-ADE7816EBZ
−40°C to +85°C
−40°C to +85°C
CP-40-10
CP-40-10
1 Z = RoHS Compliant Part.
Rev. 0| Page 45 of 48
ADE7816
NOTES
Data Sheet
Rev. 0 | Page 46 of 48
Data Sheet
NOTES
ADE7816
Rev. 0| Page 47 of 48
ADE7816
NOTES
Data Sheet
I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors).
©2012 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D10390-0-2/12(0)
Rev. 0 | Page 48 of 48
相关型号：
ADE7858AACPZ
Polyphase Multifunction Energy Metering IC With Per Phase Active And Reactive Powers
ADI
ADE7858AACPZ-RL
Polyphase Multifunction Energy Metering IC With Per Phase Active And Reactive Powers
ADI
ADE7858ACPZ
Poly Phase Multifunction Energy Metering IC with per Phase Active and Reactive Powers
ADI
ADE7858ACPZ
SPECIALTY ANALOG CIRCUIT, QCC40, 6 X 6 MM, ROHS COMPLIANT, MO-220WJJD, LFCSP-40
ROCHESTER
ADE7858ACPZ-REF
Poly Phase Multifunction Energy Metering IC with per Phase Active and Reactive Powers
ADI
©2020 ICPDF网 联系我们和版权申明