ADF4217LBRUZ-RL [ADI]
暂无描述;型号: | ADF4217LBRUZ-RL |
厂家: | ADI |
描述: | 暂无描述 射频 |
文件: | 总20页 (文件大小:220K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
a
Dual RF PLL Frequency Synthesizers
ADF4216/ADF4217/ADF4218
GENERAL DESCRIPTION
FEATURES
The ADF4216/ADF4217/ADF4218 are dual frequency synthe-
sizers that can be used to implement local oscillators (LOs) in
the upconversion and downconversion sections of wireless
receivers and transmitters. They can provide the LO for both
the RF and IF sections. They consist of a low-noise digital PFD
(Phase Frequency Detector), a precision charge pump, a pro-
grammable reference divider, programmable A and B counters,
and a dual-modulus prescaler (P/P+1). The A (6-bit) and B
(11-bit) counters, in conjunction with the dual modulus prescaler
(P/P+1), implement an N divider (N = BP + A). In addition,
the 14-bit reference counter (R Counter), allows selectable
REFIN frequencies at the PFD input. A complete PLL (Phase-
Locked Loop) can be implemented if the synthesizers are
used with an external loop filter and VCOs (Voltage Con-
trolled Oscillators).
ADF4216: 550 MHz/1.2 GHz
ADF4217: 550 MHz/2.0 GHz
ADF4218: 550 MHz/2.5 GHz
2.7 V to 5.5 V Power Supply
Selectable Charge Pump Currents
Selectable Dual Modulus Prescaler
IF: 8/9 or 16/17
RF: 32/33 or 64/65
3-Wire Serial Interface
Power-Down Mode
APPLICATIONS
Wireless Handsets (GSM, PCS, DCS, CDMA, WCDMA)
Base Stations for Wireless Radio (GSM, PCS, DCS,
CDMA, WCDMA)
Wireless LANS
Communications Test Equipment
CATV Equipment
Control of all the on-chip registers is via a simple 3-wire interface.
The devices operate with a power supply ranging from 2.7 V
to 5.5 V and can be powered down when not in use.
FUNCTIONAL BLOCK DIAGRAM
V
1
V
2
V 1
V 2
P
DD
DD
P
ADF4216/ADF4217/ADF4218
N = BP + A
11-BIT IF
B-COUNTER
PHASE
COMPARATOR
IF
IF
A
B
IN
IF
PRESCALER
CHARGE
PUMP
CP
IF
IN
6-BIT IF
A-COUNTER
IF
LOCK
DETECT
REF
OSCILLATOR
IN
14-BIT IF
R-COUNTER
OUTPUT
MUX
MUXOUT
CLOCK
DATA
LE
22-BIT
DATA
REGISTER
SDOUT
14-BIT IF
R-COUNTER
RF
LOCK
DETECT
N = BP + A
11-BIT RF
B-COUNTER
RF
RF
A
B
IN
RF
CHARGE
PUMP
PRESCALER
CP
RF
IN
6-BIT RF
A-COUNTER
PHASE
COMPARATOR
DGND
RF
AGND
RF
DGND
IF
DGND
IF
AGND
IF
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
Fax: 781/326-8703
World Wide Web Site: http://www.analog.com
© Analog Devices, Inc., 2000
ADF4216/ADF4217/ADF4218–SPECIFICATIONS1
(VDD1 = VDD2 = 3 V ؎ 10%, 5 V ؎ 10%;
VDD1, VDD2 Յ VP1, VP2 Յ 6.0 V ; AGNDRF = DGNDRF = AGNDIF = DGNDIF = 0 V; TA = TMIN to TMAX unless otherwise noted.)
P
arameter
B Version
B Chips2
Unit
Test Conditions/Comments
RF/IF CHARACTERISTICS (3 V)
RF Input Frequency (RFIN
)
See Figure 3 for Input Circuit.
ADF4216
ADF4217
ADF4218
IF Input Frequency (IFIN
RF Input Sensitivity
IF Input Sensitivity
0.2/1.2
0.2/2.0
0.5/2.5
45/550
–15/+4
–10/+4
0.2/1.2
0.2/2.0
0.5/2.5
45/550
–15/+4
–10/+4
GHz min/max
GHz min/max
GHz min/max
MHz min/max
dBm min/max
dBm min/max
For lower frequency operation (below the
minimum stated) use a square wave source.
)
Maximum Allowable
Prescaler Output Frequency3
165
165
MHz max
RF/IF CHARACTERISTICS (5 V)
RF Input Frequency (RFIN
)
See Figure 3 for Input Circuit.
ADF4216
ADF4217
ADF4218
IF Input Frequency (IFIN
RF Input Sensitivity
IF Input Sensitivity
0.2/1.2
0.2/2.0
0.5/2.5
25/550
–15/+4
–10/+4
0.2/1.2
0.2/2.0
0.5/2.5
25/550
–15/+4
–10/+4
GHz min/max
GHz min/max
GHz min/max
MHz min/max
dBm min/max
dBm min/max
For lower frequency operation (below the
minimum stated) use a square wave source.
)
Maximum Allowable
Prescaler Output Frequency3
200
200
MHz max
REFIN CHARACTERISTICS
REFIN Input Frequency
5/40
0.5
5/40
0.5
MHz min/max
V p-p min
For f < 5 MHz, use dc-coupled square wave
(0 to VDD).
AC-Coupled. When DC-Coupled:
0 to VDD max (CMOS-Compatible)
REFIN Input Sensitivity4
REFIN Input Capacitance
REFIN Input Current
10
100
10
100
pF max
µA max
PHASE DETECTOR
Phase Detector Frequency5
40
40
MHz max
CHARGE PUMP
I
CP Sink/Source
High Value
Low Value
Absolute Accuracy
CP Three-State Leakage Current
Sink and Source Current Matching
CP vs. VCP
4.5
1.125
1
1
1
4.5
1.125
1
1
1
mA typ
mA typ
% typ
nA typ
% typ
I
I
10
10
10
10
% max
% typ
0.5 V Յ VCP Յ VP – 0.5 V
VCP = VP/2
ICP vs. Temperature
LOGIC INPUTS
V
V
INH, Input High Voltage
INL, Input Low Voltage
0.8 × VDD
0.2 × VDD
1
10
0.8 × VDD
0.2 × VDD
1
10
V min
V max
µA max
pF max
µA max
I
C
INH/IINL, Input Current
IN, Input Capacitance
Oscillator Input Current
100
100
LOGIC OUTPUTS
V
OH, Output High Voltage
VDD – 0.4
0.4
VDD – 0.4
0.4
V min
V max
IOH = 500 µA
IOL = 500 µA
VOL, Output Low Voltage
POWER SUPPLIES
VDD
DD2
VP
1
2.7/5.5
2.7/5.5
V min/V max
V min/V max
V
VDD1
VDD1
VDD1/6.0
VDD1/6.0
AVDD Յ VP Յ 6.0 V
–2–
REV. 0
ADF4216/ADF4217/ADF4218
Parameter
B Version
B Chips2
Unit
Test Conditions/Comments
POWER SUPPLIES (Continued)
I
DD (RF + IF)6
ADF4216
ADF4217
ADF4218
See TPC 22 and TPC 23
18
21
25
9
12
14
mA max
mA max
mA max
9.0 mA typical at VDD = 3 V and TA = 25°C
12 mA typical at VDD = 3 V and TA = 25°C
14 mA typical at VDD = 3 V and TA = 25°C
IDD (RF Only)
ADF4216
ADF4217
10
14
18
5
7
9
mA max
mA max
mA max
5.0 mA typical at VDD = 3 V and TA = 25°C
7.0 mA typical at VDD = 3 V and TA = 25°C
9.0 mA typical at VDD = 3 V and TA = 25°C
ADF4218
I
DD (IF Only)
ADF4216
ADF4217
ADF4218
9
9
9
0.6
5
4.5
4.5
4.5
0.6
5
mA max
mA max
mA max
mA max
µA max
4.5 mA typical at VDD = 3 V and TA = 25°C
4.5 mA typical at VDD = 3 V and TA = 25°C
4.5 mA typical at VDD = 3 V and TA = 25°C
TA = 25°C
IP (IP1 + IP2)
Low-Power Sleep Mode
0.5 µA typical
NOISE CHARACTERISTICS
Phase Noise Floor7
–171
–164
–171
–164
dBc/Hz typ
dBc/Hz typ
@ 25 kHz PFD Frequency
@ 200 kHz PFD Frequency
@ VCO Output
Phase Noise Performance8
ADF4216, ADF4217, ADF4218 (IF)9
ADF4216 (RF): 900 MHz Output10
ADF4217 (RF): 900 MHz Output10
ADF4218 (RF): 900 MHz Output10
ADF4216 (RF): 836 MHz Output11
ADF4217 (RF): 1750 MHz Output12
ADF4217 (RF): 1750 MHz Output13
ADF4218 (RF): 1960 MHz Output14
Spurious Signals
–91
–87
–88
–90
–78
–85
–66
–84
–91
–87
–88
–90
–78
–85
–66
–84
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
@ 1 kHz Offset and 200 kHz PFD Frequency
@ 1 kHz Offset and 200 kHz PFD Frequency
@ 1 kHz Offset and 200 kHz PFD Frequency
@ 1 kHz Offset and 200 kHz PFD Frequency
@ 300 Hz Offset and 30 kHz PFD Frequency
@ 1 kHz Offset and 200 kHz PFD Frequency
@ 200 Hz Offset and 10 kHz PFD Frequency
@ 1 kHz Offset and 200 kHz PFD Frequency
ADF4216 ADF4217, ADF4218 (IF)9
ADF4216 (RF): 900 MHz Output10
ADF4217 (RF): 900 MHz Output10
ADF4218 (RF): 900 MHz Output10
ADF4216 (RF): 836 MHz Output11
ADF4217 (RF): 1750 MHz Output12
ADF4217 (RF): 1750 MHz Output13
ADF4218 (RF): 1960 MHz Output14
–97/–106
–98/–106
–91/–100
–80/–84
–80/–84
–88/–90
–65/–73
–80/–84
–97/–106
–98/–106
–91/–100
–80/–84
–80/–84
–88/–90
–65/–73
–80/–84
dB typ
dB typ
dB typ
dB typ
dB typ
dB typ
dB typ
dB typ
@ 200 kHz/400 kHz and 200 kHz PFD Frequency
@ 200 kHz/400 kHz and 200 kHz PFD Frequency
@ 200 kHz/400 kHz and 200 kHz PFD Frequency
@ 200 kHz/400 kHz and 200 kHz PFD Frequency
@ 30 kHz/60 kHz and 30 kHz PFD Frequency
@ 200 kHz/400 kHz and 200 kHz PFD Frequency
@ 10 kHz/20 kHz and 10 kHz PFD Frequency
@ 200 kHz/400 kHz and 200 kHz PFD Frequency
NOTES
1Operating temperature range is as follows: B Version: –40°C to +85°C.
2The B Chip specifications are given as typical values.
3This is the maximum operating frequency of the CMOS counters. The prescaler value should be chosen to ensure that the IF/RF input is divided down to a frequency that is
less than this value.
4VDD1 = VDD2 = 3 V; For VDD1 = VDD2 = 5 V, use CMOS-compatible levels.
5Guaranteed by design. Sample tested to ensure compliance.
6P = 16; RFIN = 900 MHz; IFIN = 540 MHz.
7The synthesizer phase noise floor is estimated by measuring the in-band phase noise at the output of the VCO and subtracting 20 logN (where N is the N divider value).
8The phase noise is measured with the EVAL-ADF421XEB1 Evaluation Board and the HP8562E Spectrum Analyzer. The spectrum analyzer provides the REFIN for the
synthesizer (fREFOUT = 10 MHz @ 0 dBm).
9fREFIN = 10 MHz; fPFD = 200 kHz; Offset frequency = 1 kHz; fIF = 540 MHz; N = 2700; Loop B/W = 20 kHz.
10
11
12
13
14
f
f
f
f
f
= 10 MHz; fPFD = 200 kHz; Offset frequency = 1 kHz; fRF = 900 MHz; N = 4500; Loop B/W = 20 kHz.
= 10 MHz; fPFD = 30 kHz; Offset frequency = 300 Hz; fRF = 836 MHz; N = 27867; Loop B/W = 3 kHz.
= 10 MHz; fPFD = 200 kHz; Offset frequency = 1 kHz; fRF = 1750 MHz; N = 8750; Loop B/W = 20 kHz.
= 10 MHz; fPFD = 10 kHz; Offset frequency = 200 Hz; fRF = 1750 MHz; N = 175000; Loop B/W = 1 kHz.
= 10 MHz; fPFD = 200 kHz; Offset frequency = 1 kHz; fRF = 1960 MHz; N = 9800; Loop B/W = 20 kHz.
REFIN
REFIN
REFIN
REFIN
REFIN
Specifications subject to change without notice.
–3–
REV. 0
ADF4216/ADF4217/ADF4218
(VDD1 = VDD2 = 3 V ؎ 10%, 5 V ؎ 10%; VP1, VP2 = VDD , 5 V ؎ 10%; AGND = DGND = 0 V;
TA = TMIN to TMAX unless otherwise noted.)
TIMING CHARACTERISTICS
Limit at
T
MIN to TMAX
Parameter
(B Version)
Unit
Test Conditions/Comments
t1
t2
t3
t4
t5
t6
10
10
25
25
10
20
ns min
ns min
ns min
ns min
ns min
ns min
DATA to CLOCK Setup Time
DATA to CLOCK Hold Time
CLOCK High Duration
CLOCK Low Duration
CLOCK to LE Setup Time
LE Pulsewidth
NOTES
Guaranteed by design but not production tested.
Specification subject to change without notice.
t
t
4
3
CLOCK
t
t
2
1
DB1
(CONTROL BIT C2)
DB0 (LSB)
(CONTROL BIT C1)
DATA
DB21 (MSB)
DB20
DB2
t
6
LE
LE
t
5
Figure 1. Timing Diagram
Lead Temperature, Soldering
ABSOLUTE MAXIMUM RATINGS1, 2
(TA = 25°C unless otherwise noted)
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . 215°C
VDD1 to GND3 . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
DD1 to VDD2 . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +0.3 V
VP1, VP2 to GND . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
VP1, VP2 to VDD . . . . . . . . . . . . . . . . . . . . –0.3 V to +5.5 V
Digital I/O Voltage to GND . . . . . . –0.3 V to DVDD + 0.3 V
Analog I/O Voltage to GND . . . . . . . . . –0.3 V to VP + 0.3 V
REFIN, RFINA, RFINB,
IFINA, IFINB to GND . . . . . . . . . . . –0.3 V to VDD + 0.3 V
Operating Temperature Range
Industrial (B Version) . . . . . . . . . . . . . . . . –40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Maximum Junction Temperature . . . . . . . . . . . . . . . . 150°C
TSSOP θJA Thermal Impedance . . . . . . . . . . . . . 150.4°C/W
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220°C
V
NOTES
1Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2This device is a high-performance RF integrated circuit with an ESD rating of
< 2 kV and it is ESD sensitive. Proper precautions should be taken for handling
and assembly.
1
3GND = AGND = DGND = 0 V.
TRANSISTOR COUNT
11749 (CMOS) and 522 (Bipolar).
ORDERING GUIDE
Model
Temperature Range
Package Description
Package Option*
ADF4216BRU
ADF4217BRU
ADF4218BRU
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
Thin Shrink Small Outline Package (TSSOP)
Thin Shrink Small Outline Package (TSSOP)
Thin Shrink Small Outline Package (TSSOP)
RU-20
RU-20
RU-20
*Contact the factory for chip availability.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the ADF4216/ADF4217/ADF4218 features proprietary ESD protection circuitry, permanent
damage may occur on devices subjected to high-energy electrostatic discharges. Therefore, proper
ESD precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
–4–
REV. 0
ADF4216/ADF4217/ADF4218
PIN FUNCTION DESCRIPTIONS
Pin No. Mnemonic Function
1
V
DD1
Positive Power Supply for the RF Section. Decoupling capacitors to the analog ground plane should be
placed as close as possible to this pin. VDD1 should have a value of between 2.7 V and 5.5 V. VDD1 must
have the same potential as VDD2.
2
3
VP1
CPRF
Power Supply for the RF Charge Pump. This should be greater than or equal to VDD.
Output from the RF Charge Pump. When enabled this provides ICP to the external loop filter, which in
turn drives the external VCO.
4
5
6
DGNDRF
RFINA
RFINB
Ground Pin for the RF Digital Circuitry.
Input to the RF Prescaler. This low-level input signal is normally ac-coupled to the external VCO.
Complementary Input to the RF Prescaler. This point should be decoupled to the ground plane with a small
bypass capacitor, typically 100 pF.
7
8
AGNDRF
REFIN
Ground Pin for the RF Analog Circuitry.
Reference Input. This is a CMOS input with a nominal threshold of VDD/2 and an equivalent input resis-
tance of 100 kΩ. This input can be driven from a TTL or CMOS crystal oscillator or it can be ac-coupled.
9
DGNDIF
Ground Pin for the IF Digital (Interface and Control Circuitry).
10
MUXOUT This multiplexer output allows either the IF/RF lock detect, the scaled RF, or the scaled Reference Fre-
quency to be accessed externally. See Table V.
11
12
13
CLK
DATA
LE
Serial Clock Input. This serial clock is used to clock in the serial data to the registers. The data is latched
into the 22-bit shift register on the CLK rising edge. This input is a high impedance CMOS input.
Serial Data Input. The serial data is loaded MSB first with the two LSBs being the control bits. This input is
a high impedance CMOS input.
Load Enable, CMOS Input. When LE goes high, the data stored in the shift registers is loaded into one of
the four latches, the latch being selected using the control bits.
14
15
AGNDIF
IFINB
Ground Pin for the IF Analog Circuitry.
Complementary Input to the IF Prescaler. This point should be decoupled to the ground plane with a small
bypass capacitor, typically 100 pF.
16
17
18
IFINA
DGNDIF
CPIF
Input to the IF Prescaler. This low-level input signal is normally ac-coupled to the external VCO.
Ground Pin for the IF Digital, Interface, and Control Circuitry.
Output from the IF Charge Pump. When enabled this provides ICP to the external loop filter, which in turn
drives the external VCO.
19
20
VP2
Power Supply for the IF Charge Pump. This should be greater than or equal to VDD.
V
DD2
Positive Power Supply for the IF, Interface, and Oscillator Sections. Decoupling capacitors to the analog
ground plane should be placed as close as possible to this pin. VDD2 should have a value of between 2.7 V
and 5.5 V. VDD2 must have the same potential as VDD1.
PIN CONFIGURATION
V
1
V
2
1
2
20
19
18
17
16
15
14
13
12
11
DD
V 1
DD
V 2
P
P
CP
RF
CP
3
IF
DGND
RF
DGND
4
RF
A
TSSOP
IF
IF
IN
A
B
5
IN
ADF4216/
ADF4217/
ADF4218
RF
IN
B
IF
IN
6
AGND
AGND
7
RF
IF
REF
8
LE
IN
DGND
9
DATA
CLK
IF
10
MUXOUT
–5–
REV. 0
–Typical Performance Characteristics
ADF4216/ADF4217/ADF4218
0
FREQ-UNIT PARAM-TYPE DATA-FORMAT KEYWORD IMPEDANCE – OHMS
REFERENCE
V
= 3V, V = 5V
P
DD
GHz
S
MA
R
50
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
LEVEL = –4.2dBm
I
= 4.375mA
CP
FREQ MAGS11
ANGS11
FREQ MAGS11
ANGS11
PFD FREQUENCY = 200kHz
LOOP BANDWIDTH = 20kHz
RES. BANDWIDTH = 1kHz
VIDEO BANDWIDTH = 1kHz
SWEEP = 2.5 SECONDS
AVERAGES = 30
0.0
0.957111193 –3.130429321 1.35
0.963546793 –6.686426265 1.45
0.953621785 –11.19913586 1.55
0.953757706 –15.35637483 1.65
0.816886959 –51.80711782
0.825983016 –56.20373378
0.791737125 –61.21554647
0.770543186 –61.88187496
0.793897072 –65.39516615
0.745765233 –69.24884474
0.15
0.25
0.35
0.45
0.55
0.65
0.75
0.85
0.95
1.05
1.15
1.25
0.929831379 –20.3793432
1.75
0.908459709 –22.69144845 1.85
0.897303634 –27.07001443 1.95
0.876862863 –31.32240763 2.05
0.849338092 –33.68058163 2.15
0.858403269 –38.57674885 2.25
0.841888714 –41.48606772 2.35
0.840354983 –45.97597958 2.45
0.822165839 –49.19163116 2.55
0.7517547
–71.21608147
0.745594889 –75.93169947
0.713387801 –78.8391674
0.711578577 –81.71934806
0.698487131 –85.49067481
0.669871818 –88.41958754
0.668353367 –91.70921678
–90dBc
–400kHz
–200kHz
900MHz
+200kHz
+400kHz
TPC 1. S-Parameter Data for the AD4218 RF Input
(Up to 2.5 GHz)
TPC 4. ADF4218 RF Reference Spurs (900 MHz, 200 kHz,
20 kHz)
10dB/DIVISION
–40
R
= –40dBc/Hz
RMS NOISE = 0.55؇
L
0
V
V
= 3.3V
= 3.3V
DD
–50
–60
P
–5
–10
–15
–20
–25
–30
–35
0.55؇ rms
–70
T
= +85؇C
A
–80
–90
T
= –40؇C
A
–100
–110
–120
–130
T
= +25؇C
A
–140
100Hz
1.5
2
2.5
3
0
0.5
1
FREQUENCY OFFSET FROM 900MHz CARRIER
1MHz
RF INPUT FREQUENCY – GHz
TPC 2. Input Sensitivity for the ADF4218 (RF)
TPC 5. ADF4218 RF Integrated Phase Noise (900 MHz,
200 kHz, 20 kHz)
10dB/DIVISION
–40
R
= –40dBc/Hz
RMS NOISE = 0.65؇
L
0
V
= 3V, V = 5V
P
DD
I = 4.375mA
CP
REFERENCE
LEVEL = –4.2dBm
–50
–60
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
PFD FREQUENCY = 200kHz
LOOP BANDWIDTH = 20kHz
RES. BANDWIDTH = 10Hz
VIDEO BANDWIDTH = 10Hz
SWEEP = 1.9 SECONDS
AVERAGES = 19
0.65؇ rms
–70
–80
–90
–100
–110
–120
–130
–90dBc/Hz
–140
100Hz
–2kHz
–1kHz
900MHz
+1kHz
+2kHz
FREQUENCY OFFSET FROM 900MHz CARRIER
1MHz
TPC 3. ADF4218 RF Phase Noise (900 MHz, 200 kHz, 20 kHz)
TPC 6. ADF4218 RF Integrated Phase Noise (900 MHz,
200 kHz, 35 kHz)
–6–
REV. 0
ADF4216/ADF4217/ADF4218
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
0
–10
–20
–30
–40
–50
–60
–70
V
I
= 3V, V = 5V
P
V
I
= 3V, V = 5V
P
DD
= 4.375mA
DD
REFERENCE
REFERENCE
LEVEL = –5.7dBm
LEVEL = –4.2dBm
= 4.375mA
CP
CP
PFD FREQUENCY = 30kHz
LOOP BANDWIDTH = 3kHz
RES. BANDWIDTH = 3Hz
VIDEO BANDWIDTH = 3Hz
SWEEP = 255 SECONDS
POSITIVE PEAK DETECT
MODE
PFD FREQUENCY = 200kHz
LOOP BANDWIDTH = 35kHz
RES. BANDWIDTH = 1kHz
VIDEO BANDWIDTH = 1kHz
SWEEP = 2.5 SECONDS
AVERAGES = 30
–78dBc/Hz
–89dBc
–80
–90
–100
–400kHz
–200kHz
900MHz
+200kHz
+400kHz
–80kHz
–40kHz
1750MHz
+40kHz
+80kHz
TPC 7. ADF4218 RF Reference Spurs (900 MHz, 200 kHz,
35 kHz)
TPC 10. ADF4218 RF Reference Spurs (1750 MHz,
30 kHz, 3 kHz)
–120
0
V
= 3V, V = 5V
P
V
V
= 3V
= 5V
DD
DD
REFERENCE
LEVEL = –8.0dBm
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
P
I
= 4.375mA
CP
–130
–140
–150
–160
–170
–180
PFD FREQUENCY = 30kHz
LOOP BANDWIDTH = 3kHz
RES. BANDWIDTH = 10kHz
VIDEO BANDWIDTH = 10kHz
SWEEP = 477ms
AVERAGES = 10
–74dBc/Hz
1
10
100
1000
10000
–400Hz
–200Hz
1750MHz
+200Hz
+400Hz
PHASE DETECTOR FREQUENCY – kHz
TPC 8. ADF4218 RF Phase Noise (1750 MHz, 30 kHz, 3 kHz)
TPC 11. ADF4218 RF Phase Noise vs. PFD Frequency
10dB/DIVISION
–40
R
= –40dBc/Hz
RMS NOISE = 1.8؇
L
–60
–50
–60
V
V
= 3V
= 3V
DD
P
–70
–80
–70
1.8؇ rms
–80
–90
–100
–110
–120
–130
–90
–140
100Hz
–100
–40
–20
0
20
40
60
80
100
FREQUENCY OFFSET FROM 1750MHz CARRIER
1MHz
TEMPERATURE – ؇C
TPC 9. ADF4218 RF Integrated Phase Noise (1750 MHz,
30 kHz, 3 kHz)
TPC 12. ADF4218 RF Phase Noise vs. Temperature
(900 MHz, 200 kHz, 20 kHz)
–7–
REV. 0
ADF4216/ADF4217/ADF4218
10dB/DIVISION
–40
R
= –40dBc/Hz
RMS NOISE = 0.52؇
L
–60
–50
–60
V
V
= 3V
= 5V
DD
P
0.60؇ rms
–70
–80
–70
–80
–90
–100
–110
–120
–130
–90
–140
100Hz
–100
–40
–20
0
20
40
60
80
100
FREQUENCY OFFSET FROM 900MHz CARRIER
1MHz
TEMPERATURE – ؇C
TPC 13. ADF4218 RF Reference Spurs vs. Temperature
(900 MHz, 200 kHz, 20 kHz)
TPC 16. ADF4218 IF Integrated Phase Noise (540 MHz,
200 kHz, 20 kHz)
–5
0
REFERENCE
V
= 3V, V = 5V
P
DD
–15
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
LEVEL = –4.2dBm
V
V
= 3V
DD
= 5V
I
= 5mA
CP
P
–25
–35
PFD FREQUENCY = 200kHz
LOOP BANDWIDTH = 20kHz
RES. BANDWIDTH = 10Hz
VIDEO BANDWIDTH = 10Hz
SWEEP = 2.5 SECONDS
AVERAGES = 30
–45
–55
–65
–75
–85
–95
–105
–88.0dBc
0
1
2
3
4
5
–400kHz
–200kHz
900MHz
+200kHz
+400kHz
TUNING VOLTAGE – Volts
TPC 14. ADF4218 RF Reference Spurs vs. VTUNE (900 MHz,
200 kHz, 20 kHz)
TPC 17. ADF4218 IF Reference Spurs (540 MHz, 200 kHz,
20 kHz)
–120
0
V
V
= 3V
= 5V
DD
V
I
= 3V, V = 5V
P
DD
REFERENCE
LEVEL = –4.2dBm
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
P
= 4.375mA
CP
–130
–140
–150
–160
–170
–180
PFD FREQUENCY = 200kHz
LOOP BANDWIDTH = 20kHz
RES. BANDWIDTH = 10Hz
VIDEO BANDWIDTH = 10Hz
SWEEP = 1.9 SECONDS
AVERAGES = 19
–89dBc/Hz
1
10
100
1000
10000
–2kHz
–1kHz
900MHz
+1kHz
+2kHz
PHASE DETECTOR FREQUENCY – kHz
TPC 15. ADF4218 IF Phase Noise (540 MHz, 200 kHz, 20 kHz)
TPC 18. ADF4218 IF Phase Noise vs. PFD Frequency
–8–
REV. 0
ADF4216/ADF4217/ADF4218
–60
–70
3.0
2.5
V
V
= 3V
= 3V
DD
P
V
V
= 3V
= 3V
DD
P
2.0
1.5
–80
1.0
0.5
0
–90
–100
–40
–20
0
20
40
60
80
100
0
50
100
150
200
TEMPERATURE – ؇C
PRESCALER OUTPUT FREQUENCY – MHz
TPC 19. ADF4218 IF Phase Noise vs. Temperature
(540 MHz, 200 kHz, 20 kHz)
TPC 22. DIDD vs. Prescaler Output Frequency (ADF4218,
RF Only)
10
–60
9
V
V
= 3V
= 5V
DD
ADF4218
P
8
–70
–80
7
ADF4217
6
5
ADF4216
4
3
2
1
0
–90
–100
64/65
32/33
–40
–20
0
20
40
60
80
100
PRESCALER VALUE
TEMPERATURE – ؇C
TPC 20. ADF4218 IF Reference Spurs vs. Temperature
(540 MHz, 200 kHz, 20 kHz)
TPC 23. ADF4218 AIDD vs. Prescaler Value (RF)
–5
–15
V
V
= 3V
DD
= 5V
P
–25
–35
–45
–55
–65
–75
–85
–95
–105
0
1
2
3
4
5
TUNING VOLTAGE – Volts
TPC 21. ADF4218 IF Reference Spurs vs. VTUNE (900 MHz,
200 kHz, 20 kHz)
–9–
REV. 0
ADF4216/ADF4217/ADF4218
Pulse Swallow Function
CIRCUIT DESCRIPTION
The A and B counters, in conjunction with the dual modulus
prescaler make it possible to generate output frequencies which
are spaced only by the Reference Frequency divided by R. The
equation for the VCO frequency is as follows:
REFERENCE INPUT SECTION
The reference input stage is shown below in Figure 2. SW1 and
SW2 are normally closed switches. SW3 is normally open. When
power-down is initiated, SW3 is closed and SW1 and SW2 are
opened. This ensures that there is no loading of the REFIN pin
on power-down.
f
VCO = [(P × B) + A] × fREFIN/R
fVCO = Output frequency of external voltage controlled oscilla-
POWER-DOWN
CONTROL
tor (VCO).
P
= Preset modulus of dual modulus prescaler (8/9, 16/17,
etc.).
B
A
= Preset Divide Ratio of binary 11-bit counter (1 to
2047).
NC
100k⍀
SW2
TO
= Preset Divide Ratio of binary 6-bit A counter (0 to
63).
R COUNTER
REF
IN
NC
BUFFER
SW1
fREFIN = Output frequency of the external reference frequency
SW3
oscillator.
NO
R
= Preset divide ratio of binary 14-bit programmable
reference counter (1 to 16383).
Figure 2. Reference Input Stage
IF/RF INPUT STAGE
The IF/RF input stage is shown in Figure 3. It is followed by a
2-stage limiting amplifier to generate the CML clock levels
needed for the prescaler.
R COUNTER
The 14-bit R counter allows the input reference frequency to be
divided down to produce the reference clock to the phase fre-
quency detector (PFD). Division ratios from 1 to 16,383 are
allowed.
BIAS
GENERATOR
AV
DD
N = BP+A
2k⍀
2k⍀
TO PFD
11-BIT B
COUNTER
LOAD
RF
RF
A
B
FROM IF/RF
INPUT STAGE
PRESCALER
P/P+1
IN
LOAD
6-BIT A
MODULUS
CONTROL
IN
COUNTER
N
DIVIDER
AGND
Figure 3. IF/RF Input Stage
Figure 4. A and B Counters
PRESCALER
PHASE FREQUENCY DETECTOR (PFD) AND CHARGE
PUMP
The PFD takes inputs from the R counter and N counter and
produces an output proportional to the phase and frequency
difference between them. Figure 5 is a simplified schematic.
The dual modulus prescaler (P/P+1), along with the A and B
counters, enables the large division ratio, N, to be realized
(N = BP + A). This prescaler, operating at CML levels, takes
the clock from the IF/RF input stage and divides it down to a
manageable frequency for the CMOS A and B counters. It is
based on a synchronous 4/5 core.
UP
HI
D1
Q1
The prescaler is selectable. On the IF side it can be set to
either 8/9 (DB20 of the IF AB Counter Latch set to 0) or 16/17
(DB20 set to 1). On the RF side it can be set to 64/65 (DB20 of
the RF AB Counter Latch set to 0) or 32/33 (DB20 set to 1).
See Tables IV and VI.
U1
؉ IN
CLR1
DELAY
ELEMENT
CHARGE
PUMP
U3
CP
A AND B COUNTERS
CLR2
DOWN
The A and B CMOS counters combine with the dual modulus
prescaler to allow a wide ranging division ratio in the PLL feed-
back counter. The devices are guaranteed to work when the
prescaler output is 165 MHz or less. Typically they will work
with 200 MHz output from the prescaler.
HI
D1
Q1
U1
– IN
Figure 5. PFD Simplified Schematic
–10–
REV. 0
ADF4216/ADF4217/ADF4218
MUXOUT AND LOCK DETECT
2. The IF Counter Reset mode resets the R and N counters in
the IF section and also puts the IF charge pump into three-
state. The RF Counter Reset mode resets the R and N counters
in the RF section and also puts the RF charge pump into
three-state. The IF and RF Counter Reset mode does both
of the above.
The output multiplexer on the ADF4216 family allows the
user to access various internal points on the chip. The state of
MUXOUT is controlled by P3, P4, P11 and P12. See Tables
III and V. Figure 6 shows the MUXOUT section in block dia-
gram form.
Upon removal of the reset bits, the N counter resumes counting
in close alignment with the R counter (maximum error is one
prescaler output cycle).
DV
DO
3. The Fastlock mode uses MUXOUT to switch a second loop
filter damping resistor to ground during Fastlock operation.
Activation of Fastlock occurs whenever RF CP Gain in the
RF Reference counter is set to one.
IF ANALOG LOCK DETECT
IF R COUNTER OUTPUT
IF N COUNTER OUTPUT
IF/RF ANALOG LOCK DETECT
RF R COUNTER OUTPUT
RF N COUNTER OUTPUT
RF ANALOG LOCK DETECT
MUX
CONTROL
MUXOUT
POWER-DOWN
It is possible to program the ADF4216 family for either synchro-
nous or asynchronous power-down on either the IF or RF side.
DGND
Synchronous IF Power-Down
Programming a “1” to P7 of the ADF4216 family will initiate a
power-down. If P2 of the ADF4216 family has been set to “0”
(normal operation), a synchronous power-down is conducted.
The device will automatically put the charge pump into three-
State and then complete the power-down.
Figure 6. MUXOUT Circuit
Lock Detect
MUXOUT can be programmed for analog lock detect. The N-
channel open-drain analog lock detect should be operated with
an external pull-up resistor of 10 kΩ nominal. When lock has
been detected it is high with narrow low-going pulses.
Asynchronous IF Power-Down
If P2 of the ADF4216 family has been set to “1” (three-state the
IF charge pump), and P7 is subsequently set to “1,” then an
asynchronous power-down is conducted. The device will go into
power-down on the rising edge of LE, which latches the “1” to
the IF power-down bit (P7).
INPUT SHIFT REGISTER
The functional block diagram for the ADF4216 family is shown
on Page 1. The main blocks include a 22-bit input shift register,
a 14-bit R counter and an 17-bit N counter, comprising a 6-bit
A counter and an 11-bit B counter. Data is clocked into the 22-
bit shift register on each rising edge of CLK. The data is clocked in
MSB first. Data is transferred from the shift register to one of
four latches on the rising edge of LE. The destination latch is
determined by the state of the two control bits (C2, C1) in the
shift register. These are the two LSBs DB1, DB0 as shown in
the timing diagram of Figure 1. The truth table for these bits is
shown in Table I.
Synchronous RF Power-Down
Programming a “1” to P16 of the ADF4216 family will initiate a
power-down. If P10 of the ADF4216 family has been set to “0”
(normal operation), a synchronous power-down is conducted. The
device will automatically put the charge pump into three-state
and then complete the power-down.
Asynchronous RF Power-Down
If P10 of the ADF4216 families has been set to “1” (three-state
the RF charge pump), and P16 is subsequently set to “1,” an
asynchronous power-down is conducted. The device will go into
power-down on the rising edge of LE, which latches the “1” to
the RF power-down bit (P16).
Table I. C2, C1 Truth Table
Control Bits
C2
C1
Data Latch
Activation of either synchronous or asynchronous power-down
forces the IF/RF loop’s R and N dividers to their load state
conditions and the IF/RF input section is debiased to a high
impedance state.
0
0
1
1
0
1
0
1
IF R Counter
IF AB Counter (and Prescaler Select)
RF R Counter
RF AB Counter (and Prescaler Select)
The REFIN oscillator circuit is only disabled if both the IF and
RF power-downs are set.
PROGRAM MODES
Table III and Table V show how to set up the Program Modes
in the ADF4216 family. The following should be noted:
The input register and latches remain active and are capable of
loading and latching data during all the power-down modes.
The IF/RF section of the devices will return to normal powered
up operation immediately upon LE latching a “0” to the appro-
priate power-down bit.
1. IF and RF Analog Lock Detect indicate when the PLL is in
lock. When the loop is locked and either IF or RF Analog
Lock Detect is selected, the MUXOUT pin will show a logic
high with narrow low-going pulses. When the IF/RF Analog
Lock Detect is chosen, the locked condition is indicated only
when both IF and RF loops are locked.
–11–
REV. 0
ADF4216/ADF4217/ADF4218
Table II. ADF4216 Family Latch Summary
IF REFERENCE COUNTER LATCH
CONTROL
BITS
14-BIT REFERENCE COUNTER, R
DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10
DB9
R8
DB8
R7
DB7
R6
DB6
R5
DB5
R4
DB4
R3
DB3
R2
DB2
R1
DB1
DB0
P4
P3
P2
P5
P1
R14
R13
R12
R11
R10
R9
C2 (0) C1 (0)
IF AB COUNTER LATCH
CONTROL
BITS
11-BIT B COUNTER
6-BIT A COUNTER
DB21
P7
DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10
P6 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2
DB9
B1
DB8
DB7
A6
DB6
DB5
A4
DB4
A3
DB3
A2
DB2
A1
DB1
DB0
A5
C2 (0) C1 (1)
RF REFERENCE COUNTER LATCH
CONTROL
BITS
14-BIT REFERENCE COUNTER, R
DB21
P4
DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10
P3 P2 P5 P1 R14 R13 R12 R11 R10 R9
DB9
R8
DB8
R7
DB7
R6
DB6
R5
DB5
R4
DB4
R3
DB3
R2
DB2
R1
DB1
DB0
C2 (1) C1 (0)
RF AB COUNTER LATCH
CONTROL
BITS
11-BIT B COUNTER
6-BIT A COUNTER
DB21
P7
DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10
P6 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2
DB9
B1
DB8
DB7
A6
DB6
A5
DB5
A4
DB4
A3
DB3
A2
DB2
A1
DB1
DB0
C2 (1) C1 (1)
–12–
REV. 0
ADF4216/ADF4217/ADF4218
Table III. IF Reference Counter Latch Map
CONTROL
BITS
14-BIT REFERENCE COUNTER, R
DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9
DB8
R7
DB7
R6
DB6
R5
DB5
R4
DB4
R3
DB3
R2
DB2
R1
DB1
DB0
P4
P3
P2
P5
P1
R14
R13
R12
R11
R10
R9
R8
C2 (0) C1 (0)
R14
R13
R12
..........
R3
R2
R1
DIVIDE RATIO
0
0
0
0
.
.
.
1
1
1
1
0
0
0
0
.
.
.
1
1
1
1
0
0
0
0
.
.
.
1
1
1
1
..........
..........
..........
..........
..........
..........
..........
..........
..........
..........
..........
0
0
0
1
.
.
.
1
1
1
1
0
1
1
0
.
.
.
0
0
1
1
1
0
1
0
.
.
.
0
1
0
1
1
2
3
4
.
.
.
16380
16381
16382
16383
P1
PHASE DETECTOR POLARITY
0
1
NEGATIVE
POSITIVE
P5
I
CP
0
1
1.25mA
4.375mA
P2
CHARGE PUMP
OUTPUT
0
1
NORMAL
THREE-STATE
FROM RFR LATCH
P12
P11
P4
P3
MUXOUT
0
0
0
0
0
0
1
1
1
0
0
X
X
1
1
X
X
0
0
0
1
1
0
0
0
0
1
0
1
0
1
0
1
0
1
0
LOGIC LOW STATE
IF ANALOG LOCK DETECT
IF REFERENCE DIVIDER OUTPUT
IF N DIVIDER OUTPUT
RF ANALOG LOCK DETECT
RF/IF ANALOG LOCK DETECT
RF REFERENCE DIVIDER
RF N DIVIDER
FASTLOCK OUTPUT SWITCH ON
AND CONNECTED TO MUXOUT
IF COUNTER RESET
1
1
1
0
1
1
1
1
1
1
0
1
RF COUNTER RESET
IF AND RF COUNTER RESET
–13–
REV. 0
ADF4216/ADF4217/ADF4218
Table IV. IF AB Counter Latch Map
CONTROL
BITS
11-BIT B COUNTER
6-BIT A COUNTER
DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9
DB8
DB7
A6
DB6
A5
DB5
A4
DB4
A3
DB3
A2
DB2
A1
DB1
C2 (0)
DB0
P7
P6
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
C1 (1)
A COUNTER
A6
A5
A4
A3
A2
A1
DIVIDE RATIO
X
X
X
X
.
X
X
X
X
.
0
0
0
0
.
0
0
0
0
.
0
0
1
1
.
0
1
0
1
.
0
1
2
3
.
.
.
.
.
.
.
.
.
.
.
.
X
X
X
X
1
1
1
1
1
1
0
1
14
15
B11
B10
B9
B3
B2
B1
B COUNTER DIVIDER RATIO
0
0
0
0
.
.
.
1
1
1
1
0
0
0
0
.
.
.
1
1
1
1
0
0
0
0
.
.
.
1
1
1
1
..........
..........
..........
..........
..........
..........
..........
..........
..........
..........
..........
0
0
0
0
.
.
.
1
1
1
1
0
0
1
1
.
.
.
0
0
1
1
0
1
0
1
.
.
.
0
1
0
1
NOT ALLOWED
NOT ALLOWED
NOT ALLOWED
3
.
.
.
2044
2045
2046
2047
P6
IF PRESCALER
0
1
8/9
16/17
P7
IF SECTION
N = BP + A, P IS PRESCALER VALUE SET BY P6. B MUST BE
0
1
NORMAL OPERATION
POWER-DOWN
GREATER THAN OR EQUAL TO A. TO ENSURE CONTINUOUSLY
2
ADJACENT VALUES OF N, N
IS (P – P).
MIN
–14–
REV. 0
ADF4216/ADF4217/ADF4218
Table V. RF Reference Counter Latch Map
CONTROL
BITS
14-BIT REFERENCE COUNTER, R
DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10
DB9
R8
DB8
R7
DB7 DB6
DB5
R4
DB4
R3
DB3
R2
DB2
R1
DB1
C2 (1)
DB0
P12
P11
P10
P13
P9
R14
R13
R12
R11
R10
R9
R6
R5
C1 (0)
R14
R13
R12
..........
R3
R2
R1
DIVIDE RATIO
0
0
0
0
.
.
.
1
1
1
1
0
0
0
0
.
.
.
1
1
1
1
0
0
0
0
.
.
.
1
1
1
1
..........
..........
..........
..........
..........
..........
..........
..........
..........
..........
..........
0
0
0
1
.
.
.
1
1
1
1
0
1
1
0
.
.
.
0
0
1
1
1
0
1
0
.
.
.
0
1
0
1
1
2
3
4
.
.
.
16380
16381
16382
16383
P9
0
PHASE DETECTOR POLARITY
NEGATIVE
1
POSITIVE
P13
I
CP
0
1
1.25mA
4.375mA
P10
CHARGE PUMP
OUTPUT
0
1
NORMAL
THREE-STATE
FROM IFR LATCH
P4 P3
P12
P11
MUXOUT
0
0
0
0
0
X
0
0
1
0
1
0
LOGIC LOW STATE
IF ANALOG LOCK DETECT
IF REFERENCE DIVIDER OUTPUT
0
0
0
X
1
1
1
0
0
1
0
1
IF N DIVIDER OUTPUT
RF ANALOG LOCK DETECT
RF/IF ANALOG LOCK DETECT
1
1
1
X
X
0
0
0
1
0
1
0
RF REFERENCE DIVIDER
RF N DIVIDER
FASTLOCK OUTPUT SWITCH ON AND CONNECTED TO MUXOUT
1
1
1
0
1
1
1
1
1
1
0
1
IF COUNTER RESET
RF COUNTER RESET
IF AND RF COUNTER RESET
–15–
REV. 0
ADF4216/ADF4217/ADF4218
Table VI. RF AB Counter Latch Map
CONTROL
BITS
11-BIT B COUNTER
6-BIT A COUNTER
DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9
DB8
DB7
A6
DB6
A5
DB5
A4
DB4
A3
DB3
A2
DB2
A1
DB1
C2 (1)
DB0
P16
P14
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
C1 (1)
A COUNTER
A6
A5
A4
A3
A2
A1
DIVIDE RATIO
X
X
X
X
.
X
X
X
X
.
0
0
0
0
.
0
0
0
0
.
0
0
1
1
.
0
1
0
1
.
0
1
2
3
.
.
.
.
.
.
.
.
.
.
.
.
X
X
X
X
1
1
1
1
1
1
0
1
14
15
B11
B10
B9
B3
B2
B1
B COUNTER DIVIDE RATIO
0
0
0
0
.
.
.
1
1
1
1
0
0
0
0
.
.
.
1
1
1
1
0
0
0
0
.
.
.
1
1
1
1
..........
..........
..........
..........
..........
..........
..........
..........
..........
..........
..........
0
0
0
0
.
.
.
1
1
1
1
0
0
1
1
.
.
.
0
0
1
1
0
1
0
1
.
.
.
0
1
0
1
NOT ALLOWED
NOT ALLOWED
NOT ALLOWED
3
.
.
.
2044
2045
2046
2047
P14
RF PRESCALER
0
1
64/65
32/33
P16
RF SECTION
N = BP + A, P IS PRESCALER VALUE SET BY P6. B MUST BE
0
1
NORMAL OPERATION
POWER-DOWN
GREATER THAN OR EQUAL TO A. FOR ENSURE CONTINUOUSLY
2
ADJACENT VALUES OF N, N
IS (P – P).
MIN
–16–
REV. 0
ADF4216/ADF4217/ADF4218
IF SECTION
programmable counter (B Counter). Table VI shows the input
register data format for programming the RF N counter and the
divide ratios possible.
Programmable IF Reference (R) Counter
If control bits C2, C1 are 0, 0 then the data is transferred from
the input shift register to the 14 Bit IF R counter. Table III
shows the input shift register data format for the IF R counter
and the divide ratios possible.
RF Prescaler Value
P14 in the RF AB Counter Latch sets the RF prescaler value.
Either 32/33 or 64/65 is available. See Table VI.
IF Phase Detector Polarity
RF Power-Down
Table IV and Table VI show the power-down bits in the ADF4216
family. See Power-Down section for functional description.
P1 sets the IF Phase Detector Polarity. When the IF VCO char-
acteristics are positive, this should be set to “1.” When they are
negative, it should be set to “0.” See Table III.
RF Fastlock
IF Charge Pump Three-State
The RF CP Gain bit (P17) of the RF N register in the ADF4210
family is the Fastlock Enable Bit. Only when this is “1” is IF
Fastlock enabled. When Fastlock is enabled, the RF CP current
is set to its maximum value. Also an extra loop filter damping
resistor to ground is switched in using the FLO pin, thus com-
pensating for the change in loop characteristics while in Fastlock.
Since the RF CP Gain bit is contained in the RF N Counter,
only one write is needed both to program a new output fre-
quency and to initiate Fastlock. To come out of Fastlock, the
RF CP Gain bit on the RF N register must be set to “0.” See
Table VI.
P2 puts the IF charge pump into three-state mode when pro-
grammed to a “1.” It should be set to “0” for normal operation.
See Table III.
IF Charge Pump Currents
P5 sets the IF Charge Pump current. With P5 set to “0,” ICP is
1.25 mA. With P5 set to “1,” ICP is 4.375 mA. See Table III.
Programmable IF AB Counter
If control bits C2, C1 are 0, 1, the data in the input register is
used to program the IF AB counter. The AB counter consists of
a 6-bit swallow counter (A counter) and 11-bit programmable
counter (B counter). Table IV shows the input register data
format for programming the IF AB counter and the divide ratios
possible.
APPLICATIONS SECTION
Local Oscillator for GSM Handset Receiver
Figure 7 shows the ADF4216 being used in a classic superhet-
erodyne receiver to provide the required LOs (Local Oscillators).
IF Prescaler Value
P6 in the IF AB Counter Latch sets the IF prescaler value.
Either 8/9 or 16/17 is available. See Table IV.
In this circuit, the reference input signal is applied to the circuit
at REFIN and is being generated by a 13 MHz TCXO (Tempera-
ture Controlled Crystal Oscillator).
IF Power-Down
Table III and Table V show the power-down bits in the
ADF4216 family. See Power-Down section for functional
description.
In order to have a channel spacing of 200 kHz (the GSM stan-
dard), the reference input must be divided by 65, using the
on-chip reference counter.
RF SECTION
The RF output frequency range is 1050 MHz to 1085 MHz. Loop
filter component values are chosen so that the loop bandwidth is
20 kHz. The synthesizer is set up for a charge pump current of
4.375 mA and the VCO sensitivity is 15.6 MHz/V.
Programmable RF Reference (R) Counter
If control bits C2, C1 are 1, 0, the data is transferred from the
input shift register to the 14-bit RFR counter. Table V shows
the input shift register data format for the RFR counter and the
divide ratios possible.
The IF output is fixed at 125 MHz. The IF loop bandwidth is
chosen to be 20 kHz with a channel spacing of 200 kHz. Loop
filter component values are chosen accordingly.
RF Phase Detector Polarity
P9 sets the IF Phase Detector Polarity. When the RF VCO
characteristics are positive this should be set to “1.” When they
are negative it should be set to “0.” See Table V.
Local Oscillator for WCDMA Receiver
Figure 8 shows the ADF4217 being used to generate the local
oscillator frequencies for a Wideband CDMA (WCDMA) system.
RF Charge Pump Three-State
The RF output range needed is 1720 MHz to 1780 MHz. The
VCO190–1750T will accomplish this. Channel spacing is 200 kHz
with a 20 kHz loop bandwidth. VCO sensitivity is 32 MHz/V.
Charge pump current of 4.375 mA is used and the desired phase
margin for the loop is 45°.
P10 puts the RF charge pump into three-state mode when pro-
grammed to a “1.” It should be set to “0” for normal operation.
See Table V.
RF Program Modes
Table III and Table V show how to set up the Program Modes
in the ADF4216 family.
The IF output is fixed at 200 MHz. The VCO190–200T is
used. It has a sensitivity of 11.5 MHz/V. Channel spacing and
loop bandwidth is chosen to be the same as the RF side.
RF Charge Pump Currents
P13 sets the RF Charge Pump current. With P13 set to “0,” ICP
is 1.25 mA. With P5 set to “1,” ICP is 4.375 mA. See Table V.
Programmable RF AB Counter
If control bits C2, C1 are 1, 1, the data in the input register is
used to program the RF N (AB) counter. The AB counter con-
sists of a 6-bit swallow counter (A Counter) and an 11-bit
–17–
REV. 0
ADF4216/ADF4217/ADF4218
RF
IF
OUT
OUT
V
V
P
V
P
DD
100pF
18⍀
100pF
18⍀
V 2
P
V
2
V
1
V 1
P
DD
DD
100pF
100pF
V
V
3.3k⍀
18⍀
18⍀
3.3k⍀
CC
CC
CP
CP
RF
IF
VCO190-1068U
VCO190-125T
620pF
400pF
620pF
9k⍀
620pF
18⍀
18⍀
5.8k⍀
3.9nF
6nF
ADF4216
LOCK
DETECT
MUXOUT
1nF
100pF
IF
RF
IN
IN
51⍀
51⍀
V
REF
DD
IN
CLK
DATA
LE
13MHz
TCXO
DECOUPLING CAPACITORS (22F/10pF) ON V 1, V OF THE ADF4216, THE TCXO, AND
DD
P,
ON V OF THE VCOs, HAVE BEEN OMITTED FROM THE DIAGRAM TO AID CLARITY.
CC
Figure 7. GSM Handset Receiver Local Oscillator Using the ADF4216
IF
RF
OUT
OUT
V
V
V
P
P
DD
100pF
100pF
18⍀
18⍀
18⍀
V 2
P
V
2
V
1
V 1
DD
DD
100pF
P
100pF
V
V
18⍀
3.3k⍀
3.3k⍀
18⍀
CC
CC
CP
CP
RF
IF
VCO190-200T
VCO190-1750T
450pF
2.4nF
1.5k⍀
690pF
760pF
18⍀
4.7k⍀
7.5nF
24nF
ADF4217
LOCK
DETECT
MUXOUT
1nF
100pF
RF
IN
IF
IN
51⍀
51⍀
V
REF
IN
DD
CLK
DATA
LE
10MHz
TCXO
DECOUPLING CAPACITORS (22F/10pF) ON V 1, V OF THE ADF4217, THE TCXO, AND
DD
P,
ON V OF THE VCOs, HAVE BEEN OMITTED FROM THE DIAGRAM TO AID CLARITY.
CC
Figure 8. Local Oscillator for WCDMA Receiver Using the ADF4217
–18–
REV. 0
ADF4216/ADF4217/ADF4218
INTERFACING
ADSP-2181 Interface
The ADF4216/ADF4217/ADF4218 family has a simple SPI-
compatible serial interface for writing to the device. SCLK,
SDATA, and LE (Latch Enable) control the data transfer. When
LE goes high, the 22 bits that have been clocked into the input
register on each rising edge of SCLK will be transferred to the
appropriate latch. See Figure 1 for the Timing Diagram and
Table I for the Latch Truth Table.
Figure 10 shows the interface between the ADF421x family and
the ADSP-21xx Digital Signal Processor. As previously noted,
the ADF421x family needs a 22-bit serial word for each latch
write. The easiest way to accomplish this using the ADSP-21xx
family is to use the Autobuffered Transmit Mode of operation
with Alternate Framing. This provides a means for transmitting
an entire block of serial data before an interrupt is generated.
Set up the word length for eight bits and use three memory
locations for each 22-bit word. To program each 22-bit latch,
store the three 8-bit bytes, enable the Autobuffered mode and
then write to the transmit register of the DSP. This last opera-
tion initiates the autobuffer transfer.
The maximum allowable serial clock rate is 20 MHz. This
means that the maximum update rate possible for the device is
909 kHz or one update every 1.1 ms. This is certainly more than
adequate for systems that will have typical lock times in hun-
dreds of microseconds.
ADuC812 Interface
Figure 9 shows the interface between the ADF421x family and
the ADuC812 microconverter. Since the ADuC812 is based on
an 8051 core, this interface can be used with any 8051-based
microcontroller. The microconverter is set up for SPI Master
Mode with CPHA = 0. To initiate the operation, the I/O port
driving LE is brought low. Each latch of the ADF421x family
needs a 22-bit word. This is accomplished by writing three 8-bit
bytes from the microconverter to the device. When the third
byte has been written, the LE input should be brought high to
complete the transfer.
SCLK
SCLK
DT
SDATA
LE
ADF4216/
ADF4217/
ADF4218
ADSP-21xx
TFS
MUXOUT
(LOCK DETECT)
I/O FLAG
Figure 10. ADSP-21xx to ADF421x Family Interface
On first applying power to the ADF421x family, it requires four
writes (one each to the R counter latch and the AB counter latch
for both RF1 and RF2 side) for the output to become active.
When operating in the mode described, the maximum SCLOCK
rate of the ADuC812 is 4 MHz. This means that the maximum
rate at which the output frequency can be changed will be about
180 kHz.
SCLOCK
MOSI
SCLK
SDATA
LE
ADF4216/
ADF4217/
ADF4218
ADuC812
I/O PORTS
MUXOUT
(LOCK DETECT)
Figure 9. ADuC812 to ADF421x Family Interface
–19–
REV. 0
ADF4216/ADF4217/ADF4218
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
Thin Shrink Small Outline Package (TSSOP)
(RU-20)
0.260 (6.60)
0.252 (6.40)
20
11
0.177 (4.50)
0.169 (4.30)
0.256 (6.50)
0.246 (6.25)
10
1
PIN 1
0.006 (0.15)
0.002 (0.05)
0.0433 (1.10)
MAX
8؇
0؇
0.0256 (0.65)
BSC
0.0118 (0.30)
0.0075 (0.19)
0.028 (0.70)
0.020 (0.50)
SEATING
PLANE
0.0079 (0.20)
0.0035 (0.090)
–20–
REV. 0
相关型号:
ADF4217LBRUZ-RL7
IC PLL FREQUENCY SYNTHESIZER, 3000 MHz, PDSO20, MO-153AC, TSSOP-20, PLL or Frequency Synthesis Circuit
ADI
ADF4218BCHIPS
IC PLL FREQUENCY SYNTHESIZER, 2500 MHz, UUC, DIE, PLL or Frequency Synthesis Circuit
ADI
ADF4218BRU-REEL
IC PLL FREQUENCY SYNTHESIZER, 2500 MHz, PDSO20, TSSOP-20, PLL or Frequency Synthesis Circuit
ADI
ADF4218BRU-REEL7
IC PLL FREQUENCY SYNTHESIZER, 2500 MHz, PDSO20, TSSOP-20, PLL or Frequency Synthesis Circuit
ADI
ADF4218LBRU-REEL
IC PLL FREQUENCY SYNTHESIZER, 3000 MHz, PDSO20, MO-153AC, TSSOP-20, PLL or Frequency Synthesis Circuit
ADI
©2020 ICPDF网 联系我们和版权申明