ADG659YCPZ-REEL7 [ADI]
+3 V/+5 V/±5 V CMOS 4-Channel Analog Multiplexer;型号: | ADG659YCPZ-REEL7 |
厂家: | ADI |
描述: | +3 V/+5 V/±5 V CMOS 4-Channel Analog Multiplexer 输出元件 |
文件: | 总20页 (文件大小:391K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
+3 V/+5 V/ 5 V ꢀCMO ꢁ4 ꢂan ꢃ4ꢀꢄꢂaaꢅe
Aaꢂeog Cuetipeꢅxꢅrs
Dꢂtꢂ Oꢄꢅꢅt
ADG65ꢃ/ADG659
FEATURES
FUNCTIONAL BLOCK DIAGRAM
2 V to 6 V dual supply
2 V to 12 V single supply
Automotive temperature range −40°C to +125°C
<0.1 nA leakage currents
ADG659
ADG658
S1
S1A
S4A
DA
DB
45 Ω on resistance over full signal range
Rail-to-rail switching operation
D
Single 8-to-1 multiplexer ADG658
Differential 4-to-1 multiplexer ADG659
16-lead LFCSP/TSSOP/QSOP packages
Typical power consumption <0.1 μW
TTL/CMOS compatible inputs
S1B
S4B
S8
1 OF 8
DECODER
1 OF 4
DECODER
Package upgrades to 74HC4051/74HC4052 and
MAX4051/MAX4052/MAX4581/MAX4582
A0 A1 A2 EN
A0
A1
EN
SWITCHES SHOWN FOR A LOGIC 1 INPUT
APPLICATIONS
Figure 1.
Automotive applications
Automatic test equipment
Data acquisition systems
Battery-powered systems
Communication systems
Audio and video signal routing
Relay replacement
Sample-and-hold systems
Industrial control systems
GENERAL DESCRIPTION
The ADG658 and ADG659 are low voltage, CMOS analog
multiplexers comprised of eight single channels and four
differential channels, respectively. The ADG658 switches one of
eight inputs (S1–S8) to a common output, D, as determined by
the 3-bit binary address lines A0, A1, and A2. The ADG659
switches one of four differential inputs to a common differential
output, as determined by the 2-bit binary address lines A0 and
The ADG658 and ADG659 are available in 16-lead TSSOP/
QSOP packages and 16-lead 4 mm × 4 mm LFCSP packages.
PRODUCT HIGHLIGHTS
1. Single- and dual-supply operation. The ADG658 and
ADG659 offer high performance and are fully specified
and guaranteed with 5 V, +5 V, and +3 V supply rails.
2. Automotive temperature range −40°C to +125°C.
3. Low power consumption, typically <0.1 μW.
4. 16-lead 4 mm × 4 mm LFCSP packages, 16-lead TSSOP
package and 16-lead QSOP package.
EN
A1. An
input on both devices enables or disables the device.
When disabled, all channels are switched off.
These devices are designed on an enhanced process that provides
lower power dissipation yet gives high switching speeds. These
devices can operate equally well as either multiplexers or demul-
tiplexers and have an input range that extends to the supplies. All
channels exhibit break-before-make switching action, preventing
momentary shorting when switching channels. All digital inputs
have 0.8 V to 2.4 V logic thresholds, ensuring TTL/CMOS logic
compatibility when using single +5 V or dual 5 V supplies.
Rev. D
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2004–2016 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADG658/ADG659
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Absolute Maximum Ratings ............................................................9
ESD Caution...................................................................................9
Pin Configurations and Function Descriptions......................... 11
Typical Performance Characteristics ........................................... 12
Terminology.................................................................................... 15
Test Circuits..................................................................................... 16
Outline Dimensions....................................................................... 19
Ordering Guide .......................................................................... 20
Automotive Products................................................................. 20
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description......................................................................... 1
Product Highlights ........................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Dual Supply ................................................................................... 3
5 V Single Supply.......................................................................... 5
2.7 V to 3.6 V Single Supply........................................................ 7
REVISION HISTORY
11/2016—Rev. C to Rev. D
2/2009—Rev. A to Rev. B
Changes to Figure 3 and Table 7................................................... 11
Updated Outline Dimensions....................................................... 19
Changes to Ordering Guide .......................................................... 20
Changes to Ordering Guide.......................................................... 20
7/2004—Rev. 0 to Rev. A
Updated Format..................................................................Universal
Added QSOP Package Outline ..................................................... 20
Changes to Ordering Guide.......................................................... 20
3/03—Rev. 0: Initial Version
9/2014—Rev. B to Rev. C
Moved Terminology Section......................................................... 15
Updated Outline Dimensions....................................................... 19
Changes to Ordering Guide .......................................................... 20
Rev. D | Page 2 of 20
Data Sheet
ADG658/ADG659
SPECIFICATIONS
DUAL SUPPLY
VDD = +5 V 10%, VSS = −5 V 10%, GND = 0 V, unless otherwise noted.
Table 1.
B Version
Y Version
−40°C
to +85°C
−40°C
to+125°C Unit
Parameter
+25°C
Test Conditions/Comments
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
VSS to VDD
100
V
VDD = +4.5 V, VSS = −4.5 V
VS = 4.5 V, IS = 1 mA; see Figure 21
45
75
1.3
3
10
16
Ω typ
Ω max
Ω typ
Ω max
Ω typ
Ω max
90
3.2
17
On Resistance Match between
Channels (∆RON)
On Resistance Flatness (RFLAT(ON)
3.5
VS = 3.5 V, IS = 1 mA
VDD = +5 V, VSS = −5 V;
VS = 3 V, IS = 1 mA
)
18
LEAKAGE CURRENTS
VDD = +5.5 V, VSS = −5.5 V
Source OFF Leakage IS (OFF)
0.005
0.2
nA typ
nA max
nA typ
nA max
nA max
nA typ
nA max
nA max
VD = 4.5 V, VS = 4.5 V; see Figure 22
5
Drain OFF Leakage ID (OFF)
ADG658
ADG659
Channel ON Leakage ID, IS (ON)
ADG658
ADG659
0.005
0.2
0.1
0.005
0.2
0.1
VD = 4.5 V, VS = 4.5 V; see Figure 23
5
2.5
VD = VS = 4.5 V; see Figure 24
5
2.5
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current
2.4
0.8
V min
V max
IINL or IINH
0.005
2
µA typ
µA max
pF typ
VIN = VINL or VINH
1
CIN, Digital Input Capacitance
DYNAMIC CHARACTERISTICS1
tTRANSITION
80
115
80
115
30
45
ns typ
ns max
ns typ
ns max
ns typ
ns max
ns typ
ns min
pC typ
pC max
dB typ
% typ
RL = 300 Ω, CL = 35 pF
VS = 3 V; see Figure 25
140
140
50
165
165
55
tON (EN)
tOFF (EN)
RL = 300 Ω, CL = 35 pF
VS = 3 V; see Figure 27
RL = 300 Ω, CL = 35 pF
VS = 3 V; see Figure 27
RL = 300 Ω, CL = 35 pF
VS1 = VS2 = 3 V; see Figure 26
VS = 0 V, RS = 0 Ω,
CL = 1 nF; see Figure 28
RL = 50 Ω, CL = 5 pF, f = 1 MHz; see Figure 29
RL = 600 Ω, 2 V p-p, f = 20 Hz to 20 kHz
Break-Before-Make Time Delay, tBBM
Charge Injection
50
10
2
4
Off Isolation
Total Harmonic Distortion, THD + N
−90
0.025
Channel-to-Channel Crosstalk
(ADG659)
−90
dB typ
RL = 50 Ω, CL = 5 pF, f = 1 MHz; see Figure 31
−3 dB Bandwidth
ADG658
ADG659
210
400
MHz typ RL = 50 Ω, CL = 5 pF; see Figure 30
MHz typ
Rev. D | Page 3 of 20
ADG658/ADG659
Data Sheet
B Version
Y Version
−40°C
to +85°C
−40°C
to+125°C Unit
Parameter
CS (OFF)
+25°C
Test Conditions/Comments
4
pF typ
f = 1 MHz
CD (OFF)
ADG658
ADG659
23
12
pF typ
pF typ
f = 1 MHz
f = 1 MHz
CD, CS (ON)
ADG658
ADG659
28
16
pF typ
pF typ
f = 1 MHz
f = 1 MHz
POWER REQUIREMENTS
IDD
VDD = +5.5 V, VSS = −5.5 V
Digital Inputs = 0 V or 5.5 V
0.01
0.01
µA typ
µA max
µA typ
µA max
1
1
ISS
Digital Inputs = 0 V or 5.5 V
1 Guaranteed by design; not subject to production test.
Rev. D | Page 4 of 20
Data Sheet
ADG658/ADG659
5 V SINGLE SUPPLY
VDD = 5 V 10%, VSS = 0 V, GND = 0 V, unless otherwise noted.
Table 2.
B Version Y Version
−40°C
to +85°C
−40°C
to +125°C Unit
Parameter
+25°C
Test Conditions/Comments
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
0 to VDD
200
V
VDD = 4.5 V, VSS = 0 V
VS = 0 V to 4.5 V, IS = 1 mA; see Figure 21
85
150
4.5
8
Ω typ
Ω max
Ω typ
Ω max
Ω typ
160
On Resistance Match between
Channels (∆RON)
On Resistance Flatness (RFLAT(ON)
LEAKAGE CURRENTS
VS = 3.5 V, IS = 1 mA
9
14
10
16
)
13
VDD = 5 V, VSS = 0 V, VS = 1.5 V to 4 V, IS = 1 mA
VDD = 5.5 V
Source OFF Leakage IS (OFF)
0.005
0.2
0.005
0.2
0.1
0.005
0.2
nA typ
nA max
nA typ
nA max
nA max
nA typ
nA max
nA max
VS = 1 V/4.5 V, VD = 4.5 V/1 V; see Figure 22
5
Drain OFF Leakage ID (OFF)
ADG658
ADG659
Channel ON Leakage ID, IS (ON)
ADG658
ADG659
VS = 1 V/4.5 V, VD = 4.5 V/1 V; see Figure 23
VS = VD = 1 V or 4.5 V, see Figure 24
5
2.5
5
2.5
0.1
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current
2.4
0.8
V min
V max
IINL or IINH
0.005
2
µA typ
µA max
pF typ
VIN = VINL or VINH
1
CIN, Digital Input Capacitance
DYNAMIC CHARACTERISTICS1
tTRANSITION
120
200
120
190
35
ns typ
ns max
ns typ
ns max
ns typ
ns max
ns typ
ns min
pC typ
pC max
dB typ
dB typ
RL = 300 Ω, CL = 35 pF
VS = 3 V; see Figure 25
RL = 300 Ω, CL = 35 pF
270
245
60
300
280
70
tON (EN)
tOFF (EN)
VS = 3 V; see Figure 27
RL = 300 Ω, CL = 35 pF
50
100
VS = 3 V; see Figure 27
RL = 300 Ω, CL = 35 pF
VS1 = VS2 = 3 V; see Figure 26
VS = 2.5 V, RS = 0 Ω, CL = 1 nF; see Figure 28
Break-Before-Make Time Delay, tBBM
Charge Injection
10
0.5
1
−90
−90
Off Isolation
Channel-to-Channel Crosstalk
(ADG659)
RL = 50 Ω, CL = 5 pF, f = 1 MHz; see Figure 29
RL = 50 Ω, CL = 5 pF; f = 1 MHz; see Figure 31
−3 dB Bandwidth
ADG658
ADG659
180
330
5
MHz typ
MHz typ
pF typ
RL = 50 Ω, CL = 5 pF; see Figure 30
f = 1 MHz
CS (OFF)
CD (OFF)
ADG658
ADG659
29
15
pF typ
pF typ
f = 1 MHz
f = 1 MHz
Rev. D | Page 5 of 20
ADG658/ADG659
Data Sheet
B Version Y Version
−40°C
to +85°C
−40°C
to +125°C Unit
Parameter
CD, CS (ON)
ADG658
+25°C
Test Conditions/Comments
30
16
pF typ
pF typ
f = 1 MHz
f = 1 MHz
ADG659
POWER REQUIREMENTS
IDD
VDD = 5.5 V
Digital Inputs = 0 V or 5.5 V
0.01
µA typ
1
µA max
1 Guaranteed by design; not subject to production test.
Rev. D | Page 6 of 20
Data Sheet
ADG658/ADG659
2.7 V TO 3.6 V SINGLE SUPPLY
VDD = 2.7 to 3.6 V, VSS = 0 V, GND = 0 V, unless otherwise noted.
Table 3.
B Version Y Version
−40°C
to +85°C
−40°C
to +125°C Unit
Parameter
+25°C
Test Conditions/Comments
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
0 to VDD
400
V
VDD = 2.7 V, VSS = 0 V
VS = 0 V to 2.7 V, IS = 0.1 mA; see Figure 21
185
300
2
Ω typ
Ω max
Ω typ
Ω max
350
6
On Resistance Match between
Channels (∆RON)
VS = 1.5 V, IS = 0.1 mA
4.5
7
LEAKAGE CURRENTS
VDD = 3.3 V
Source OFF Leakage IS (OFF)
0.005
0.2
0.005
0.2
0.1
0.005
0.2
nA typ
nA max
nA typ
nA max
nA max
nA typ
nA max
nA max
VS = 1 V/3 V, VD = 3 V/1 V; see Figure 22
5
Drain OFF Leakage ID (OFF)
ADG658
ADG659
Channel ON Leakage ID, IS (ON)
ADG658
ADG659
VS = 1 V/3 V, VD = 3 V/1 V; see Figure 23
VS = VD = 1 V or 3 V, see Figure 24
5
2.5
5
2.5
0.1
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current
2.0
0.5
V min
V max
IINL or IINH
0.005
2
µA typ
µA max
pF typ
VIN = VINL or VINH
1
CIN, Digital Input Capacitance
DYNAMIC CHARACTERISTICS1
tTRANSITION
200
370
230
370
50
ns typ
ns max
ns typ
ns max
ns typ
ns max
ns typ
ns min
pC typ
pC max
dB typ
dB typ
RL = 300 Ω, CL = 35 pF
VS = 1.5 V; see Figure 25
RL = 300 Ω, CL = 35 pF
440
440
90
490
490
110
10
tON (EN)
VS = 1.5 V; see Figure 27
RL = 300 Ω, CL = 35 pF
tOFF (EN)
80
200
VS = 1.5 V; see Figure 27
RL = 300 Ω, CL = 35 pF
VS1 = VS2 = 1.5 V; see Figure 26
VS = 1.5 V, RS = 0 Ω, CL = 1 nF; see Figure 28
Break-Before-Make Time Delay, tBBM
Charge Injection
1
2
−90
−90
Off Isolation
Channel-to-Channel Crosstalk
(ADG659)
RL = 50 Ω, CL = 5 pF, f = 1 MHz; see Figure 29
RL = 50 Ω, CL = 5 pF; f = 1 MHz; see Figure 31
−3 dB Bandwidth
ADG658
ADG659
160
300
5
MHz typ
MHz typ
pF typ
RL = 50 Ω, CL = 5 pF; see Figure 30
f = 1 MHz
CS (OFF)
CD (OFF)
ADG658
ADG659
29
15
pF typ
pF typ
f = 1 MHz
f = 1 MHz
Rev. D | Page 7 of 20
ADG658/ADG659
Data Sheet
B Version Y Version
−40°C
to +85°C
−40°C
to +125°C Unit
Parameter
CD, CS (ON)
ADG658
+25°C
Test Conditions/Comments
30
16
pF typ
pF typ
f = 1 MHz
f = 1 MHz
ADG659
POWER REQUIREMENTS
IDD
VDD = 3.6 V
Digital Inputs = 0 V or 3.6 V
0.01
µA typ
1
µA max
1 Guaranteed by design; not subject to production test.
Rev. D | Page 8 of 20
Data Sheet
ADG658/ADG659
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Table 4.
Parameter
Rating
VDD to VSS
13 V
VDD to GND
VSS to GND
Analog Inputs1
Digital Inputs1
−0.3 V to +13 V
+0.3 V to −6.5 V
VSS − 0.3 V to VDD + 0.3 V
GND − 0.3 V to VDD + 0.3 V
or 10 mA, whichever
occurs first
ESD CAUTION
Peak Current, S or D
40 mA
(Pulsed at 1 ms, 10% duty cycle max)
Continuous Current, S or D
Operating Temperature Range
Automotive (Y Version)
Industrial (B Version)
Storage Temperature Range
Junction Temperature
θJA Thermal Impedance
16-Lead QSOP
20 mA
−40°C to +125°C
−40°C to +85°C
−65°C to +150°C
150°C
104°C/W
150.4°C/W
70°C/W
16-Lead TSSOP
16-Lead LFCSP (4-Layer Board)
Lead Temperature, Soldering
Vapor Phase (60 sec)
Infrared (15 sec)
215°C
220°C
5.5 kV
ESD
1
EN
Over voltages at AX, , S, or D are clamped by internal diodes. Current must
be limited to the maximum ratings.
Rev. D | Page 9 of 20
ADG658/ADG659
Data Sheet
Table 5. ADG658 Truth Table
A2
A1
A0
Switch Condition
EN
1
0
0
0
0
0
0
0
X1
0
0
0
0
1
1
1
1
X1
0
0
1
1
0
0
1
1
X1
0
1
0
1
0
1
0
1
None
1
2
3
4
5
6
7
8
0
1 X = Don’t Care
Table 6. ADG659 Truth Table
A1
A0
On Switch Pair
EN
X1
0
0
1
X1
0
1
0
1
0
0
0
0
None
1
2
3
4
1
1
1 X = Don’t Care
Rev. D | Page 10 of 20
Data Sheet
ADG658/ADG659
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
16
15
14
13
12
11
10
9
S5
S7
D
V
S1B
S3B
DB
V
DD
DD
S3
S2
S1
S4
A0
A1
A2
S3A
S2A
DA
ADG658
TOP VIEW
(Not to Scale)
ADG659
TOP VIEW
(Not to Scale)
S8
S6
S4B
S2B
S1A
S4A
A0
EN
EN
V
V
SS
SS
GND
GND
A1
Figure 2. 16-Lead TSSOP/QSOP Pin Configuration
1
2
3
4
12 S2
11 S1
10 S4
1
2
3
4
12 S2A
D
S8
S6
EN
DB
S4B
S2B
EN
11 DA
ADG658
TOP VIEW
(Not to Scale)
ADG659
TOP VIEW
(Not to Scale)
10 S1A
9
A0
9
S4A
NOTES
1. EXPOSED PAD. THE EXPOSED PAD MUST BE LEFT FLOATING.
Figure 3. 16-Lead, 4 mm × 4 mm LFCSP Pin Configuration
Table 7. Pin Function Descriptions
Parameter
Description
VDD
VSS
IDD
ISS
Most Positive Power Supply Potential.
Most Negative Power Supply Potential.
Positive Supply Current.
Negative Supply Current.
GND
S
D
Ground (0 V) Reference.
Source Terminal. Can be an input or output.
Drain Terminal. Can be an input or output.
Logic Control Input.
AX
EN
Active Low Digital Input. When high, device is disabled and all switches are OFF. When low, AX logic inputs determine
ON switch.
EPAD (LFCSP Only)
Exposed Pad. The exposed pad must be left floating.
Rev. D | Page 11 of 20
ADG658/ADG659
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
100
T
= 25°C
A
140
120
100
80
90
80
70
60
50
40
30
20
10
0
+125°C
V
, V = ±2.7V
DD SS
+85°C
V
, V = ±3V
DD SS
+25°C
60
V
, V = ±5.5V
DD SS
V
, V = ±4.5V
DD SS
–40°C
40
V
, V = ±5V
DD SS
20
V
V
= 5V
= 0V
DD
SS
0
–5.5
–3.5
–1.5
0.5
2.5
4.5
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
V
, V (V)
S
V
, V (V)
S
D
D
Figure 4. On Resistance vs. VD (VS) for Dual Supply
Figure 7. On Resistance vs. VD (VS) for Different Temperatures (Single Supply)
250
200
150
100
50
300
T
= 25°C
A
V
= 2.7V
DD
+85°C
250
200
150
100
50
+125°C
V
= 3V
DD
V
= 3.3V
DD
+25°C
V
= 4.5V
DD
V
= 5V
DD
–40°C
V
= 5.5V
DD
V
V
= 3V
= 0V
DD
SS
V
= 12V
4
V
= 10V
8
DD
DD
0
0
0
2
6
10
12
0
0.5
1.0
1.5
, V (V)
2.0
2.5
3.0
V
, V (V)
S
D
V
D
S
Figure 5. On Resistance vs. VD (VS) for Single Supply
Figure 8. On Resistance vs. VD (VS) for Different Temperatures (Single Supply)
100
90
80
70
60
50
40
30
20
10
0
1.5
V
V
V
V
= 5V
= –5V
= ±4V
= ±4V
DD
SS
1.0
0.5
D
S
I
(OFF)
+125°C
S
+85°C
+25°C
0
I
(OFF)
D
–0.5
–1.0
–1.5
–2.0
–2.5
–40°C
I , I (ON)
S
D
V
V
= +5V
= –5V
DD
SS
–5
–4
–3
–2
–1
0
1
2
3
4
5
0
20
40
60
80
100
120
V
, V (V)
S
D
TEMPERATURE (°C)
Figure 9. Leakage Current vs. Temperature (Dual Supply)
Figure 6. On Resistance vs. VD (VS) for Different Temperatures (Dual Supply)
Rev. D | Page 12 of 20
Data Sheet
ADG658/ADG659
350
300
250
200
150
100
50
1.5
V
V
V
V
= +5V
= 0V
V
= 0V
DD
SS
SS
1.0
0.5
V
= 3V
= ±4V
DD
D
S
±
I
(OFF)
S
=
1V
0
I
(OFF)
V
= 5V
D
DD
–0.5
–1.0
–1.5
–2.0
–2.5
tON
I
, I (ON)
D
S
V
= 3V
DD
V
V
V
V
= +3V
= 0V
DD
SS
= ±2.4V
D
S
±
tOFF
V
= 5V
=
1V
DD
0
–40
0
20
40
60
80
100
120
–20
0
20
40
60
80
100
120
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 10. Leakage Current vs. Temperature (Single Supply)
Figure 13. tON/tOFF Times vs. Temperature (Single Supply)
14
0
TA = 25°C
–1
–2
12
10
8
–3
–4
–5
–6
6
–7
–8
4
–9
–10
–11
–12
–13
–14
–15
2
V
V
= +5V
= –5V
DD
SS
0
V
V
= +5V
= –5V
= 25°C
DD
SS
V
V
= +5V
= 0V
DD
SS
–2
T
A
–4
–5
100k
1M
10M
100M
–4
–3
–2
–1
0
1
2
3
4
5
FREQUENCY (Hz)
V
(V)
S
Figure 11. Charge Injection vs. Source Voltage
Figure 14. ON Response vs. Frequency (ADG658)
140
120
100
80
0
V
V
= +5V
= –5V
DD
SS
–2
–4
–6
tON
–8
–10
–12
–14
–16
–18
–20
–22
–24
60
tOFF
40
V
V
= +5V
= –5V
DD
20
SS
T
= 25°C
A
0
–40
–20
0
20
40
60
80
100
120
100k
1M
10M
100M
TEMPERATURE (°C)
FREQUENCY (Hz)
Figure 12. tON/tOFF Times vs. Temperature (Dual Supply)
Figure 15. ON Response vs. Frequency (ADG659)
Rev. D | Page 13 of 20
ADG658/ADG659
Data Sheet
0
10000
1000
100
10
V
= 0V
SS
V
V
= +5V
= –5V
= 25°C
DD
SS
–20
–40
T
A
V
= 12V
DD
V
= 5V
DD
–60
1
–80
V
= 3V
DD
0.1
–100
–120
0.01
100k
1M
10M
100M
0
2
4
6
V(EN) (V)
8
10
12
FREQUENCY (Hz)
Figure 19. VDD Current vs. Logic Level
Figure 16. OFF Isolation vs. Frequency
3.0
0
–10
V
V
= –5V
= +5V
DD
SS
T
= 25°C
A
–20
2.5
2.0
1.5
1.0
0.5
0
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
–130
0
2
4
6
8
10
12
100k
1M
10M
100M
V
(V)
FREQUENCY (Hz)
DD
Figure 17. Crosstalk vs. Frequency
Figure 20. Logic Threshold Voltage vs. Supply Voltage
100
10
600Ω
IN AND OUT
V
V
= +5V
= –5V
= 25°C
DD
SS
T
A
1
0.1
0.01
20
50
100
200
500
1k
2k
5k
10k
20k
FREQUENCY (Hz)
Figure 18. THD + Noise
Rev. D | Page 14 of 20
Data Sheet
ADG658/ADG659
TERMINOLOGY
VD (VS)
CD, CS (ON)
Analog Voltage on Terminals D, S.
ON Switch Capacitance. Measured with reference to ground.
RON
CIN
Ohmic Resistance between D and S.
Digital Input Capacitance.
∆RON
tON
On Resistance Match between Any Two Channels, i.e., RONmax
− RONmin.
Delay between Applying the Digital Control Input and the
Output Switching ON. See Figure 27.
RFLAT(ON)
tOFF
Flatness is defined as the difference between the maximum and
minimum value of ON Resistance as measured over the
specified analog signal range.
Delay between Applying the Digital Control Input and the
Output Switching OFF.
tBBM
IS (OFF)
ON Time. Measured between 80% points of both switches when
switching from one address state to another.
Source Leakage Current with the Switch OFF.
ID (OFF)
Charge Injection
Drain Leakage Current with the Switch OFF.
Measure of the Glitch Impulse Transferred from the Digital
Input to the Analog Output during Switching.
ID, IS (ON)
Channel Leakage Current with the Switch ON.
Off Isolation
Measure of Unwanted Signal Coupling through an OFF Switch.
VINL
Maximum Input Voltage for Logic 0.
Crosstalk
Measure of Unwanted Signal Coupled through from One
Channel to Another as a Result of Parasitic Capacitance.
VINH
Minimum Input Voltage for Logic 1.
Bandwidth
I
INL (IINH)
The Frequency at which the Output is Attenuated by 3 dB.
Input Current of the Digital Input.
On Response
The Frequency Response of the ON Switch.
CS (OFF)
OFF Switch Source Capacitance. Measured with reference to
ground.
Insertion Loss
The Loss Due to the ON Resistance of the Switch.
CD (OFF)
OFF Switch Drain Capacitance. Measured with reference to
ground.
Rev. D | Page 15 of 20
ADG658/ADG659
TEST CIRCUITS
Data Sheet
I
DS
V
V
SS
DD
V1
V
V
SS
DD
S1
S2
S8
D
I
(OFF)
A
S
D
D
V
S
V
O
EN
V
S
GND
LOGIC 1
R
= V /I
1
ON
DS
Figure 21. ON Resistance
Figure 23. ID (OFF)
V
V
V
DD
SS
V
V
SS
DD
V
DD
SS
V
V
SS
DD
I
(OFF)
A
S
S1
S2
S8
I
(ON)
A
S1
S8
D
D
D
V
S
V
D
EN
LOGIC 1
EN
V
V
D
S
GND
GND
Figure 24. ID (ON)
Figure 22. IS (OFF)
V
V
SS
DD
3V
0V
ADDRESS
DRIVE (V
V
V
SS
DD
50%
50%
)
IN
A2
V
S1
S1
V
A1
A0
IN
50Ω
S2–S7
V
S8
S8
V
ADG658*
GND
S1
S8
90%
V
D
OUT
EN
R
L
300Ω
C
35pF
V
L
OUT
90%
V
* SIMILAR CONNECTION FOR ADG659
tTRANSITION
tTRANSITION
Figure 25. Switching Time of Multiplexer, tTRANSITION
V
V
V
V
DD
SS
3V
ADDRESS
DD
SS
DRIVE (V
)
IN
A2
V
S1
S
V
A1
A0
IN
50Ω
0V
S2–S7
S8
ADG658*
GND
V
D
OUT
EN
80%
80%
R
C
V
OUT
L
L
300Ω
35pF
tBBM
* SIMILAR CONNECTION FOR ADG659
Figure 26. Break-Before-Make Delay, tBBM
Rev. D | Page 16 of 20
Data Sheet
ADG658/ADG659
V
V
SS
DD
3V
0V
ENABLE
DRIVE (V
V
V
SS
DD
50%
50%
)
IN
A2
A1
A0
V
S1
S
S2–S8
tOFF (EN)
ADG658*
GND
V
O
0.9V
0.9V
O
O
V
D
OUT
EN
C
35pF
R
300Ω
OUTPUT
L
L
V
IN
50Ω
0V
tON (EN)
* SIMILAR CONNECTION FOR ADG659
EN
( ), tOFF
EN
( )
Figure 27. Enable Delay, tON
V
V
SS
DD
A2 V
V
SS
DD
3V
A1
A0
S
LOGIC INPUT
ADG658*
(V
)
IN
R
S
D
0V
V
OUT
C
1nF
V
S
L
EN
V
GND
IN
V
∆V
OUT
OUT
Q
= C × ∆V
L OUT
INJ
* SIMILAR CONNECTION FOR ADG659
Figure 28. Charge Injection
V
V
V
V
V
DD
SS
DD
SS
0.1µF
0.1µF
0.1µF
0.1µF
NETWORK
ANALYZER
V
V
SS
V
DD
DD
SS
A2
A1
A0
A2
A1
A0
50Ω
50Ω
S
S
50Ω
V
V
S
S
D
D
V
V
OUT
OUT
LOGIC 1
EN
EN
R
R
L
L
50Ω
50Ω
GND
GND
V
OUT
V
WITH SWITCH
OFF ISOLATION = 20 LOG
OUT
V
INSERTION LOSS = 20 LOG
S
V
WITHOUT SWITCH
OUT
Figure 30. Bandwidth
Figure 29. Off Isolation
Rev. D | Page 17 of 20
ADG658/ADG659
Data Sheet
V
V
V
V
DD
SS
0.1µF
0.1µF
DD
SS
A1
A0
NETWORK
ANALYZER
EN
ADG659
GND
NETWORK
ANALYZER
50Ω
DA
DB
S1A
V
OUT
S1B
DB
R
L
50Ω
50Ω
V
S
DA
V
OUT
CHANNEL-TO-CHANNEL CROSSTALK = 20 LOG
V
S
Figure 31. Channel-to-Channel Crosstalk
Rev. D | Page 18 of 20
Data Sheet
ADG658/ADG659
OUTLINE DIMENSIONS
5.10
5.00
4.90
16
9
8
4.50
4.40
4.30
6.40
BSC
1
PIN 1
1.20
MAX
0.15
0.05
0.20
0.09
0.75
0.60
0.45
8°
0°
0.30
0.19
0.65
BSC
SEATING
PLANE
COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-153-AB
Figure 32. 16-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-16)
Dimensions shown in millimeters
DETAIL A
(JEDEC 95)
4.10
4.00 SQ
3.90
0.35
0.30
0.25
PIN 1
INDICATOR
PIN 1
INDIC ATOR AREA OPTIONS
(SEE DETAIL A)
13
16
0.65
BSC
1
12
2.25
2.10 SQ
1.95
EXPOSED
PAD
9
4
8
5
0.70
0.60
0.50
0.25 MIN
TOP VIEW
BOTTOM VIEW
0.80
0.75
0.70
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
0.05 MAX
0.02 NOM
COPLANARITY
SECTION OF THIS DATA SHEET.
0.08
SEATING
PLANE
0.203 REF
COMPLIANT TO JEDEC STANDARDS MO-220-WGGC.
Figure 33. 16-Lead Lead Frame Chip Scale Package [LFCSP]
4 mm × 4 mm Body and 0.75 mm Package Height
(CP-16-23)
Dimensions shown in millimeters
Rev. D | Page 19 of 20
ADG658/ADG659
Data Sheet
0.197 (5.00)
0.193 (4.90)
0.189 (4.80)
16
1
9
8
0.158 (4.01)
0.154 (3.91)
0.150 (3.81)
0.244 (6.20)
0.236 (5.99)
0.228 (5.79)
0.010 (0.25)
0.006 (0.15)
0.020 (0.51)
0.010 (0.25)
0.069 (1.75)
0.053 (1.35)
0.065 (1.65)
0.049 (1.25)
0.010 (0.25)
0.004 (0.10)
0.041 (1.04)
REF
SEATING
PLANE
8°
0°
0.025 (0.64)
BSC
0.050 (1.27)
0.016 (0.41)
COPLANARITY
0.004 (0.10)
0.012 (0.30)
0.008 (0.20)
COMPLIANT TO JEDEC STANDARDS MO-137-AB
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 34. 16-Lead Shrink Small Outline Package [QSOP]
(RQ-16)
Dimensions shown in inches and (millimeters)
ORDERING GUIDE
Model1, 2
Temperature Range
−40°C to +125°C
Package Description
Package Option
RU-16
ADG658YRU
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Lead Frame Chip Scale Package [LFCSP]
16-Lead Lead Frame Chip Scale Package [LFCSP]
16-Lead Shrink Small Outline Package [QSOP]
16-Lead Shrink Small Outline Package [QSOP]
16-Lead Shrink Small Outline Package [QSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Lead Frame Chip Scale Package [LFCSP]
16-Lead Lead Frame Chip Scale Package [LFCSP]
16-Lead Shrink Small Outline Package [QSOP]
ADG658YRU-REEL7
ADG658YRUZ
ADG658YRUZ-REEL7
ADG658YCPZ
ADG658YCPZ-REEL7
ADG658YRQ
ADG658YRQZ
ADG658YRQZ-REEL7
ADW54003-0
ADW54003-0RL7
ADG659YRU
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +85°C
−40°C to +85°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +85°C
−40°C to +85°C
−40°C to +125°C
RU-16
RU-16
RU-16
CP-16-23
CP-16-23
RQ-16
RQ-16
RQ-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
CP-16-23
CP-16-23
RQ-16
ADG659YRUZ
ADG659YRUZ-REEL7
ADG659WYRUZ-REEL7
ADG659YCPZ
ADG659YCPZ-REEL7
ADG659YRQZ
1 Z = RoHS Compliant Part.
2 W = Qualified for Automotive Applications.
AUTOMOTIVE PRODUCTS
The ADW54003 models are available with controlled manufacturing to support the quality and reliability requirements of automotive
applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers
should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in
automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to
obtain the specific Automotive Reliability reports for these models.
©2004–2016 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D03273-0-11/16(D)
Rev. D | Page 20 of 20
相关型号:
ADG659YRUZ-REEL7
4-CHANNEL, DIFFERENTIAL MULTIPLEXER, PDSO16, ROHS COMPLIANT, MO-153AB, TSSOP-16
ROCHESTER
©2020 ICPDF网 联系我们和版权申明