ADM1177-1ARMZ-R7 [ADI]
Hot Swap Controller and Digital Power Monitor with Soft-Start Pin; 热插拔控制器和数字电源监控器与软启动引脚
| 型号： | ADM1177-1ARMZ-R7 |
| 厂家： | 
ADI |
| 描述： | Hot Swap Controller and Digital Power Monitor with Soft-Start Pin |
| 文件： | 总16页 (文件大小：204K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Hot Swap Controller and
Digital Power Monitor with Soft-Start Pin
Preliminary Technical Data
ADM1177
FEATURES
FUNCTIONAL BLOCK DIAGRAM
Allows Safe Board Insertion and Removal from a Live
Backplane
ADM1177
Controls Supply Voltages from 3.15 V to 14V
Precision Current Sense Amplifier
Precision Voltage Input
12-Bit ADC for Current and Voltage Readback
Charge Pumped Gate Drive for External N-FET Switch
Adjustable Analog Current Limit with Circuit Breaker
Fast Response Limits Peak Fault Current
Automatic Retry or Latch-Off On Current Fault
Programmable hot swap timing via TIMER pin
Mux
V
I
VCC
0
1
SDA
SCL
ADR
12-Bit
ADC
+
A
-
I2C
SENSE
Current Sense
Amplifier
FET Drive
Controller
GATE
+
ON
-
1.3V
Soft-start pin for reference adjustment and programming of
initial current ramp rate
UV Comparator
Active-high ON pin
SS
TIMER
GND
I2C Fast Mode compliant interface (400 KHz max)
10-lead MSOP package
Figure 1.
APPLICATIONS DIAGRAM
RSENSE
APPLICATIONS
N-Channel FET
3.15V - 14V
Power Monitoring/Power Budgeting
Central office Equipment
SENSE
VCC
Telecommunication and Datacommunication Equipment
PC/Servers
CONTROLLER
GATE
ADM1177
SDA
SCL
SDA
SCL
ON
SS
GENERAL DESCRIPTION
P=VI
The ADM1177 is an integrated hot-swap controller which offers
digital current and voltage monitoring via an on-chip 12-bit
ADC, communicated through an I2C interface.
TIMER
ADR
GND
An internal current sense amplifier senses voltage across the
sense resistor in the power path via the VCC and SENSE pins.
Figure 2.
A Soft-start (SS) pin is also included. This gives the user control
over the reference on the current sense amplifier. An internal
current source will charge a capacitor on this pin at startup,
allowing the user set the profile of the initial current ramp. A
voltage can also be driven on this pin to alter the reference.
The ADM1177 limits the current through this resistor by
controlling the gate voltage of an external N-channel FET in the
power path, via the GATE pin. The sense voltage (and hence the
inrush current) is kept below a preset maximum.
A 12-bit ADC can measure the current seen in the sense
resistor, and also the supply voltage on the VCC pin.
The ADM1177 protects the external FET by limiting the time
that it spends with the maximum current running in it. This
current limit period is set by the choice of capacitor attached to
the TIMER pin. Additionally, the device provides protection
from overcurrent events at times after the hot-swap event is
complete. In the case of a short-circuit event the current in the
sense resistor will exceed an overcurrent trip threshold, and the
FET will be switched off immediately by pulling down the
GATE pin.
An industry standard I2C interface allows a controller to read
current and voltage data from the ADC. Measurements can be
initiated by an I2C command. Alternatively the ADC can run
continuously and the user can read the latest conversion data
whenever it is required. Up to 4 unique I2C addresses can be
created by the way the ADR pin is connected.
The ADM1177 is packaged in a 10-lead MSOP package.
Rev. PrD May 2006
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
© 2006 Analog Devices, Inc. All rights reserved.
ADM1177
Preliminary Technical Data
TABLE OF CONTENTS
REVISION HISTORY
May 06—Revision PrD: Preliminary Version
Rev. PrD | Page 2 of 16
Preliminary Technical Data
ADM1177
ADM1177—SPECIFICATIONS
VVCC = 3.15V to 14V, TA = −40°C to +85°C, Typical Values at TA = +25°C unless otherwise noted.
Table 1.
Parameter
Min
Typ
Max
Units
Conditions
VVCC Rising
ON rising
VCC Pin
Operating Voltage Range, VVCC
Supply Current, ICC
Undervoltage Lockout, VUVLO
Undervoltage Lockout Hysteresis, VUVLOHYST
ON Pin
3.15
14
3
V
mA
V
1.6
2.8
25
mV
Input Current, IINON
−100
0
+100
nA
V
mV
µs
Trip Threshold, VONTH
Trip Threshold Hysteresis, VONHYST
Glitch Filter Time
1.3
80
3
SS Pin
Pullup Current, IISSPU
Current Setting Gain, GAINSS
10
10
µA
V/V
VSS = 0V to 1V
VSS / VCB. Valid until VSS = 1V, then consider
the gain as 10.
Soft-start Completion Voltage, SSHIGHV
Pullup Current, IISSPUD
1.3
100
V
µA
SS continues to pull up beyond 1V
Under Fault
SENSE Pin
Input Leakage, ISENSE
Overcurrent Fault Timing Threshold, VOCTIM
−1
85
+1
µA
mV
VSENSE = VVCC
VOCTRIM = (VVCC − VSENSE), Fault timing starts
on the TIMER pin
Overcurrent Limit Threshold, VLIM
90
100
110
115
mV
mV
VLIM = (VVCC − VSENSE), Closed loop regulation
to a current limit
VOCFAST = (VVCC − VSENSE), Gate pulldown
current turned on
Fast Overcurrent Trip Threshold, VOCFAST
GATE Pin
Drive Voltage, VGATE
Drive Voltage, VGATE
Drive Voltage, VGATE
Pullup Current
Pulldown Current
Pulldown Current
5
6
5
10
7
8
7
12
2
10
12
10
14
V
V
V
µA
mA
mA
VGATE − VVCC, VVCC = 3.15 V
VGATE − VVCC, VVCC = 5 V
VGATE − VVCC, VVCC = 13.2 V
VGATE = 0 V
VGATE = 3 V, VVCC > UVLO
VGATE = 3 V, VVCC < UVLO
25
TIMER Pin
Pull-Up Current (Power On Reset), ITIMERUPPOR
Pull-Up Current (Fault Mode), ITIMERUPFAULT
Pull-Down Current (Retry Mode), ITIMERDNRETRY
−4
−48
−5
−60
2
−6
−72
2.5
µA
µA
µA
Initial Cycle, VTIMER = 1 V
During Current Fault, VTIMER = 1 V
After current fault and during a cool-down
period on a retry device, VTIMER = 1 V
Pull-Down Current, ITIMERDN
Trip Threshold High, VTIMERH
Trip Threshold Low, VTIMERL
ADR Pin
100
1.3
0.2
µA
V
V
Normal Operation, VTIMER = 1 V
TIMER rising
TIMER falling
1.235
0.18
1.365
0.22
Set address to 00, VADRLOWV
Set address to 01, RADRLOWZ
0
135
0.8
165
V
kΩ
Low state
Resistor to ground state, load pin with
specified resistance for 01 decode
150
Set address to 10, IADRHIGHZ
−1
2
+1
µA
Open state, maximum load allowed on
ADR pin for 10 decode
High state
VADR = 2.0 V to 5.5 V
VADR = 0 V to 0.8 V
Set address to 11, VADRHIGHV
Input current for 11 decode, IADRLOW
Input current for 00 decode, IADRHIGH
5.5
5
V
µA
µA
3
−22
−40
Rev. PrD | Page 3 of 16
ADM1177
Preliminary Technical Data
Parameter
MONITORING ACCURACY1
Min
Typ
Max
Units
Conditions
Current Sense Absolute Accuracy
TBD
−2.3
TBD
−2.5
TBD
−2.8
−3.5
TBD
+2.2
TBD
+2.5
TBD
+2.8
+3.5
%
%
%
%
%
%
%
VSENSE = 75 mV
VSENSE = 75 mV, @ 0°C to +70°C
VSENSE = 50mV
VSENSE = 50 mV, @ 0°C to +70°C
VSENSE = 25mV
VSENSE = 25mV, @ 0°C to +70°C
VSENSE = 12.5 mV, @ 25°C
Current Sense Accuracy, TC
VSENSE for ADC full-scale
Voltage Sense Accuracy
0.01
105
0
%/°C
mV
%
%
V
−1.5
−1.5
+1.5
+1.5
VVCC = 3.0 V to 5.5V(VRANGE = 1)
VVCC = 10.8 V to 13.2V(VRANGE = 0)
VRANGE = 1
0
VCC for ADC full-scale, low range
VCC for ADC full-scale, high range
6.656
26.6282
V
VRANGE = 0
I2C Timing3
Low level input voltage, VIL
High level input voltage, VIH
Low level output voltage on SDA, VOL
Output fall time on SDA from VIHMIN to VILMAX
Maximum width of spikes suppressed by input
filtering on SDA and SCL pins
0.99
V
V
V
ns
ns
2.31
0.4
250
250
IOL = 3mA
20+0.1CB
50
CB = bus capacitance from SDA to GND
Input current, II, on SDA/SCL when not driving out −10
a logic low
Input capacitance on SDA/SCL
SCL clock frequency, fSCL
+10
400
µA
5
pF
kHz
ns
ns
ns
ns
ns
ns
LOW period of the SCL clock
600
HIGH period of the SCL clock
1300
600
100
Setup time for a repeated START condition, tSU;STA
SDA output data hold time, tHD;DAT
Set-up time for a stop condition, tSU;STO
600
Bus free time between a STOP and a START
condition, tBUF
1300
Capacitive load for each bus line
400
pF
1 Monitoring accuracy is a measure of the error in a code that is read back for a particular voltage/current. This is a combination of amplifier error, reference error and
ADC error.
2The maximum operating voltage is limited to VVCC =14 V which corresponds to an ADC code of 871.
3The following conditions apply to all timing specifications: VBUS =3.3V, TA =25°C. All timings refer to VIHMIN and VILMAX
.
Rev. PrD | Page 4 of 16
Preliminary Technical Data
ADM1177
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
Rating
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only. Functional operation of the device at these or any
other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute
maximum rating conditions may affect device reliability.
Ambient temperature = 25°C, unless otherwise noted.
VCC Pin
SENSE Pin
TIMER Pin
ON Pin
SS Pin
GATE Pin
SDA, SCL Pins
ADR Pin
Power Dissipation
Storage Temperature
20 V
20 V
−0.3 V to +6 V
−0.3 V to +20 V
TBD
30 V
−0.3 V to +6 V
−0.3 V to +6 V
TBD
−65°C to +125°C
Operating Temperature Range −40°C to +85°C
Lead Temperature Range
(Soldering 10 sec)
Junction Temperature
300°C
150°C
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the
human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. PrD | Page 5 of 16
ADM1177
Preliminary Technical Data
PIN CONFIGURATIONS
10
9
1
2
Vcc
GATE
ADM1177
TOP VIEW
SS
SENSE
ON
8
ADR
3
7
6
4
5
SDA
SCL
GND
(NOT TO SCALE)
TIMER
Figure 3. Pin Configurations
PIN FUNCTIONAL DESCRIPTIONS
Table 3.
Pin No. Name
Description
1
VCC
Positive supply input pin. The operating supply voltage range is between 3.15 V to 14 V. An undervoltage
lockout (UVLO) circuit resets the ADM1177 when a low supply voltage is detected.
2
SENSE
Current sense input pin. A sense resistor between the VCC and SENSE pins sets the analog current limit. The
hotswap operation of the ADM1177 controls the external FET gate to maintain the (VVCC-VSENSE) voltage at 100
mV or below.
3
ON
Undervoltage input pin. Active high pin. An internal ON comparator has a trip threshold of 1.3 V and the
output of this comparator is used as an enable for the hotswap operation. With an external resistor divider
from VCC to GND, this pin can be used to enable the hotswap operation one a specific voltage on VCC, giving
an undervoltage function.
4
5
GND
TIMER
Chip Ground Pin
Timer pin. An external capacitor CTIMER sets a 270 ms/µF initial timing cycle delay and a 21.7 ms/µF fault
delay. The GATE pin turns off whenever the TIMER pin is pulled beyond the upper threshold. An overvoltage
detection with an external zener can be used to force this pin high.
6
7
8
SCL
SDA
ADR
I2C Clock Pin. Open-drain output requires an external resistive pull-up.
I2C Data I/O Pin. Open-drain output requires an external resistive pull-up.
I2C Address Pin. This pin can be tied low, tied high, left floating or tied low through a resistor to set four
different I2C addresses.
9
SS
Soft-Start Pin. This pin controls the reference on the current sense amplifier. A 10 µA current source charges
this pin at startup. A capacitor on this pin will then set the slope of the initial current ramp. This pin can also
be driven to a voltage to alter the reference directly, thereby adjusting the current limit level.
10
GATE
GATE Output Pin. This pin is the high side gate drive of an external N-channel FET. This pin is driven by the FET
drive controller which utilises a charge pump to provide a 12 µA pull-up current to charge the FET gate pin.
The FET drive controller regulates to a maximum load current (100 mV through the sense resistor) by
modulating the GATE pin.
Rev. PrD | Page 6 of 16
Preliminary Technical Data
ADM1177
OVERVIEW OF THE HOTSWAP FUNCTION
using the TIMER pin to time a cool-down period in between
hotswap attempts. The current and voltage threshold
combinations on the TIMER pin set the retry duty cycle to
3.8%.
When circuit boards are inserted into a live backplane,
discharged supply bypass capacitors would draw large transient
currents from the backplane power bus as they charge. Such
transient currents can cause permanent damage to connector
pins, and dips on the backplane supply which could reset other
boards in the system. The ADM1177 is designed to turn a
circuit board’s supply voltage on and off in a controlled manner,
allowing the circuit board to be safely inserted into or removed
from a live backplane. The ADM1177 can reside either on the
backplane or on the circuit board itself.
The ADM1177 is designed to operate over a range of supplies
from 3.15 V to 14 V.
UNDERVOLTAGE LOCKOUT
An internal undervoltage lockout (UVLO) circuit resets the
ADM1177 if the VCCsupply is too low for normal operation.
The UVLO has a low-to-high threshold of 2.8 V, with 25 mV
hysteresis. Above 2.8 V supply voltage, the ADM1177 will start
the initial timing cycle.
The ADM1177 controls the “inrush” current to a fixed
maximum level by modulating the gate of an external N-
channel FET placed between the live supply rail and the load.
This “hotswap” function protects the card connectors and the
FET itself from damage and also limits any problems which
could be caused by the high current loads on the live supply rail.
ON FUNCTION
The ADM1177-1 has an active-high ON pin. The ON pin is the
input to a comparator which has a low-to-high threshold of 1.3
V, an 80 mV hysteresis and a glitch filter of 3 μs. A low input on
the ON pin turns off the hotswap operation by pulling the
GATE pin to ground, turning off the external FET. The TIMER
pin is also reset by turning on a pull-down current on this pin.
A low-to-high transition on the ON pin starts the hotswap
operation. A 10 kΩ pull-up resistor connecting the ON pin to
the supply is recommended.
The ADM1177 holds the GATE pin down (and thus the FET is
held off) until a number of conditions are met. An undervoltage
lockout circuit ensures that the device is being provided with an
adequate input supply voltage. Once this has been successfully
detected, the device goes through an initial timing cycle to
provide a delay before it will attempt to hotswap. This delay
ensures that the board is fully seated in the backplane before the
board is powered up.
Alternatively, an external resistor divider at the ON pin can be
used to program an undervoltage lockout value higher than the
internal UVLO circuit, thereby setting a voltage level at the
VCC supply where the hotswap operation is to start. An RC
filter can be added at the ON pin to increase the delay time at
card insertion if the initial timing cycle delay is insufficient.
Once the initial timing cycle is complete, the hotswap function
is switched on under control of the ON pin. When asserted high
the hotswap operation starts.
The ADM1177 charges up the gate of the FET to turn on the
load. It will continue to charge up the GATE pin until the linear
current limit (set to 100 mV/RSENSE) is reached. For some
combinations of low load capacitance and high current limit,
this limit may not be reached before the load is fully charged up.
If current limit is reached, the ADM1177 will regulate the
GATE pin to keep the current at this limit. For currents above
the overcurrent fault timing threshold, nominally 100 mV/
RSENSE, the current fault is timed by sourcing a current out to the
TIMER pin. If the load becomes fully charged before the fault
current limit time is reached (when the TIMER pin reaches
1.3 V), the current will drop below the overcurrent fault timing
threshold, the ADM1177 will then charge the GATE pin higher
to fully enhance the FET for lowest RON, and the TIMER pin
will be pulled down again.
SOFT START (SS PIN)
The SS pin is used to determine the inrush current profile.
A capacitor should be attached to this pin. Whenever the FET
is requested to turn on, the SS pin is held at ground until the
SENSE pin reaches a few mV. A current source is then turned
on, which linearly ramps the capacitor up to 1.3V. The
reference voltage for the GATE linear control amplifier is
derived from the soft start voltage, such that the inrush linear
current limit is defined as ILIMIT = VSS / (20 x RSENSE). A voltage
can also be driven onto the SS pin to clamp the reference at a
different level.
If the fault current limit time is reached before the load drops
below the current limit, a fault has been detected, and the
hotswap operation is aborted by pulling down on the GATE pin
to turn off the FET. The ADM1177-2 latches off at this point
and will only attempt to hotswap again when the ON pin is de-
asserted then asserted again. The ADM1177-1 will retry the
hotswap operation indefinitely, keeping the FET in SOA by
Rev. PrD | Page 7 of 16
ADM1177
Preliminary Technical Data
threshold, VOCFAST, is exceeded, the 2 mA GATE pull-down is
turned on immediately. This pulls the GATE voltage down
quickly to enable the ADM1177 to limit the length of the
current spike that gets through, and also to bring the current
through the sense resistor back into linear regulation as quickly
as possible. This protects the backplane supply from sustained
overcurrent conditions, which may otherwise have caused
problems with the backplane supply level dropping too low.
TIMER FUNCTION
The TIMER pin handles several timing functions with an
external capacitor, CTIMER. There are two comparator thresholds:
VTIMERH (0.2 V) and VTIMERL (1.3 V). The four timing current
sources are a 5 µA and a 60 µA pull-up, and a 2 µA and a
100 µA pull-down. The 100 µA is a non-ideal current source
approximating a 7 kΩ resistor below 0.4 V.
These current and voltage levels, together with the value of
CTIMER that the user chooses, determine the initial timing cycle
time, the fault current limit time, and the hotswap retry duty
cycle.
CALCULATING CURRENT LIMITS AND FAULT
CURRENT LIMIT TIME
The nominal linear current limit is determined by a sense
resistor connected between the VCC and SENSE pins as given
by the equation below:
GATE AND TIMER FUNCTIONS DURING A
HOTSWAP
ILIMIT(NOM) = VLIM(NOM)/RSENSE = 100 mV/RSENSE
The minimum linear fault current is given by Equation 2:
ILIMIT(MIN) = VLIM(MIN)/RSENSE(MAX) = 90 mV/RSENSE(MAX)
The maximum linear fault current is given by Equation 3:
ILIMIT(MAX) = VLIM(MAX)/RSENSE(MIN) = 110 mV/RSENSE(MIN)
(1)
(2)
(3)
During hot insertion of a board onto a live supply rail at VCC,
the abrupt application of supply voltage charges the external
FET drain/gate capacitance, which could cause an unwanted
gate voltage spike. An internal circuit holds GATE low before
the internal circuitry wakes up. This reduces the FET current
surges substantially at insertion. The GATE pin is also held low
during the initial timing cycle, and until the ON pin has been
taken high to start the hotswap operation.
The power rating of the sense resistor should be rated at the
maximum linear fault current level.
During hotswap operation the GATE pin is first pulled up by a
12 μA current source. If the current through the sense resistor
reaches the overcurrent fault timing threshold, Voctim, then a
pull-up current of 60 µA on the TIMER pin is turned on, and
this pin starts charging up. At a slightly higher voltage in the
sense resistor, the error amplifier servos the GATE pin to
maintain a constant current to the load by controlling the
The minimum overcurrent fault timing threshold current is
given by
IOCTIM(MIN) = VOCTIM(MIN)/RSENSE(MAX) = 85 mV/RSENSE(MAX)
(4)
The maximum fast overcurrent trip threshold current is given
by
voltage across the sense resistor to the linear current limit, VLIM
.
A normal hotswap will complete when the board supply
capacitors near full charge and the current through the sense
resistor drops, to eventually reach the level of the board load
current. As soon as the current drops below the overcurrent
fault timing threshold, the current into the TIMER pin will
switch from being a 60 μA pull-up to a 100 μA pull-down. The
ADM1177 will then drive the GATE voltage as high as it can to
fully enhance the FET and reduce RON losses to a minimum.
IOCFAST(MAX) = VOCFAST(MAX)/RSENSE(MIN) = 115 mV/RSENSE(MIN)(5)
The fault current limit time is the time that a device will spend
timing an overcurrent fault, and is given by
t
FAULT ~= 21.7 × CTIMER ms/μF
(6)
INITIAL TIMING CYCLE
When VCC is first connected to the backplane supply, there is
an internal supply (time-point (1) in Figure 4) in the ADM1177
which needs to charge up. A very short time later (significantly
less than 1 ms) the internal supply will be fully up and, since the
undervoltage lockout voltage has been exceeded at VCC, the
device will come out of reset. During this first short reset period
the GATE pin is held down with a 25 mA pulldown current,
and the TIMER pin is pulled down with a 100 μA current sink.
A hotswap will fail if the load current fails to drop below the
overcurrent fault timing threshold, VOCTIM, before the TIMER
pin has charged up to 1.3 V. In this case the GATE pin is then
pulled down with a 2 mA current sink. The GATE pull-down
will stay on until a hotswap retry starts, which can be forced by
de-asserting then re-asserting the ON pin, or the device will
retry automatically after a cool-down period, on the ADM1177-
1.
The ADM1177 then goes through an initial timing cycle. At
point (2) the TIMER pin is pulled high with 5 µA. At time point
(3), the TIMER reaches the VTIMERL threshold and the first
portion of the initial cycle ends. The 100 µA current source
then pulls down the TIMER pin until it reaches 0.2 V at time
The ADM1177 also features a method of protection from
sudden load current surges, such as a low impedance fault,
when the current seen across the sense resistor may go well
beyond the linear current limit. If the fast overcurrent trip
Rev. PrD | Page 8 of 16
Preliminary Technical Data
ADM1177
(1)
(2)
(3)(4)
(5)(6)
(7)
point (4). The initial cycle delay (time point 2 to time point 4) is
related to CTIMER by equation:
V
VCC
t
INITIAL ~= 270 × CTIMER ms/μF
(7)
When the initial timing cycle terminates, the device is ready to
start a hotswap operation (assuming ON pin is asserted). In the
example shown in Figure 4, the ON pin was asserted at the
same time as VCC was applied, so the hotswap operation starts
immediately after time-point (4). At this point the FET gate is
charged up with a 12 μA current source. At timepoint (5) the
threshold voltage of the FET is reached and the load current
begins to flow. The FET is controlled to keep the sense voltage
at 100 mV (this corresponds to a maximum load current level
defined by the value of RSENSE). At timepoint (6) VGATE and VOUT
have reached their full potential and the load current has settled
to its nominal level. Figure 5 illustrates the situation where the
ON pin is asserted after VVCC is applied.
V
ON
V
TIMER
V
GATE
V
SENSE
V
OUT
(1)
(2)
(3)(4)(5)
(6)
INITIAL TIMING
CYCLE
V
VCC
Figure 5. Start-up (ON asserts after power is applied)
HOTSWAP RETRY CYCLE ON ADM1177-1
V
ON
With the ADM1177-1 the device will turn off the FET after an
overcurrent fault, and will then use the TIMER pin to time a
delay before automatically retrying to hotswap.
V
TIMER
As with all ADM1177 devices, on overcurrent fault is timed by
charging the TIMER cap with a 60 μA pull-up current, and
when the TIMER pin reaches 1.3 V the fault current limit time
has been reached and the GATE pin is pulled down. On the
ADM1177-1, the TIMER pin is then pulled down with a 2 μA
current sink. When the TIMER pin reaches 0.2 V, it will
automatically restart the hotswap operation.
V
GATE
V
SENSE
V
OUT
The cool down period is related to CTIMER by equation:
INITIAL TIMING
CYCLE
Figure 4. Start-up (ON asserts as power is applied)
t
COOL ~ = 550 × CTIMER ms/μF
(8)
(9)
The retry duty cycle is thus given by
tFAULT/(tCOOL + tFAULT ) × 100% = 3.8%
Rev. PrD | Page 9 of 16
ADM1177
Preliminary Technical Data
high. This indicates that a data stream will follow. All slave
peripherals connected to the serial bus respond to the
START condition, and shift in the next 8 bits, consisting
of a 7-bit slave address (MSB first) plus a R/W bit, which
determines the direction of the data transfer, i.e. whether
data will be written to or read from the slave device (0 =
write, 1 = read).
VOLTAGE AND CURRENT READBACK
In addition to providing hot swap functionality, the ADM1177
also contains the components to allow voltage and current
readback over an I2C bus. The voltage output of the current
sense amplifier and the voltage on the VCC pin are fed into a
12-bit ADC via a multiplexer. The device can be instructed to
convert voltage and/or current at any time during operation via
an I2C command. When all conversions are complete the
voltage and/or current values can be read out to 12-bit
accuracy in two or three bytes.
The peripheral whose address corresponds to the
transmitted address responds by pulling the data line low
during the low period before the ninth clock pulse, known
as the acknowledge bit, and holding it low during the high
period of this clock pulse. All other devices on the bus
now remain idle while the selected device waits for data to
be read from or written to it. If the R/W bit is a 0, the
master will write to the slave device. If the R/W bit is a 1,
the master will read from the slave device.
SERIAL BUS INTERFACE
Control of the ADM1177 is carried out via the Inter-IC Bus
(I2C). This interface is compatible with fastmode I2C (400 kHz
max). The ADM1177 is connected to this bus as a slave device,
under the control of a master device.
2.
Data is sent over the serial bus in sequences of nine clock
pulses, eight bits of data followed by an acknowledge bit
from the slave device. Data transitions on the data line
must occur during the low period of the clock signal and
remain stable during the high period, as a low to high
transition when the clock is high may be interpreted as a
STOP signal.
IDENTIFYING THE ADM1177 ON THE I2C BUS
The ADM1177 has a 7-bit serial bus slave address. When the
device is powered up, it will do so with a default serial bus
address. The five MSBs of the address are set to 10110, the two
LSBs are determined by the state of the ADR pin. There are four
different configurations available on the ADR pin which
correspond to four different I2C addresses for the two LSBs.
These are explained in Table 4 below. This scheme allows four
ADM1177 devices to operation on a single I2C bus.
If the operation is a write operation, the first data byte
after the slave address is a command byte. This tells the
slave device what to expect next. It may be an instruction
such as telling the slave device to expect a block write, or
it may simply be a register address that tells the slave
where subsequent data is to be written.
Table 4. Setting I2C Addresses via the ADR Pin
ADR Configuration
Address
Since data can flow in only one direction as defined by the
R/W bit, it is not possible to send a command to a slave
device during a read operation. Before doing a read
operation, it may first be necessary to do a write operation
to tell the slave what sort of read operation to expect
and/or the address from which data is to be read.
Low state
0xB0
0xB2
0xB4
0xB6
Resistor to GND
Floating (unconnected)
High state
GENERAL I2C TIMING
3.
When all data bytes have been read or written, stop
conditions are established. In WRITE mode, the master
will pull the data line high during the 10th clock pulse to
assert a STOP condition. In READ mode, the master
device will release the SDA line during the low period
before the ninth clock pulse, but the slave device will not
pull it low. This is known as No Acknowledge. The master
will then take the data line low during the low period
before the 10th clock pulse, then high during the 10th clock
pulse to assert a STOP condition.
Figure 6 and Figure 7 show timing diagrams for general read
and write operations using the I2C. The I2C specification defines
specific conditions for different types of read and write
operation, which are discussed later. The general I2C protocol
operates as follows:
1.
The master initiates data transfer by establishing a START
condition, defined as a high to low transition on the serial
data line SDA while the serial clock line SCL remains
Rev. PrD | Page 10 of 16
Preliminary Technical Data
ADM1177
9
9
1
1
SCL
0
0
A1
A0
R/W
D7
D6
D5
1
D4
D3
D2
D1
D0
1
1
1
SDA
ACK. BY
SLAVE
ACK. BY
SLAVE
START BY MASTER
FRAME 2
FRAME 1
SLAVE ADDRESS
COMMAND CODE
1
9
9
SCL
(CONTINUED)
SDA
(CONTINUED)
D7
D6
D5
D4
D3
D2
D1
D0
D7
D6
D5
D4
D3
D2
D1
D0
STOP
BY
MASTER
ACK. BY
SLAVE
ACK. BY
SLAVE
FRAME N
DATA BYTE
FRAME 3
DATA BYTE
Figure 6. General I2C Write Timing Diagram
1
9
1
9
SCL
SDA
D6
D5
1
D4
D3
D2
D1
D0
0
0
A1
A0 R/W
D7
1
1
1
ACK. BY
SLAVE
ACK. BY
MASTER
START BY MASTER
FRAME 1
SLAVE ADDRESS
FRAME 2
DATA BYTE
1
9
9
SCL
(CONTINUED)
SDA
(CONTINUED)
D7
D6
D5
D4
D3
D2
D1
D0
D7
D6
D5
D4
D3
D2
D1
D0
STOP
BY
MASTER
ACK. BY
MASTER
NO ACK.
FRAME 3
DATA BYTE
FRAME N
DATA BYTE
Figure 7. General I2C Read Timing Diagram
tHD;STA
tLOW
tR
tF
SCL
tHIGH
tSU;STA
tSU;STO
tHD;STA
tSU;DAT
tHD;DAT
SDA
tBUF
S
P
P
S
Figure 8. Serial Bus Timing Diagram
Rev. PrD | Page 11 of 16
ADM1177
Preliminary Technical Data
WRITE COMMAND BYTE
WRITE AND READ OPERATIONS
The I2C specification defines several protocols for different
types of read and write operations. The ones used in the
ADM1177 are discussed below. The following abbreviations are
used in the diagrams:
In this operation the master device sends a command byte to
the slave device, as follows:
1. The master device asserts a start condition on SDA.
Table 5. I2C abbreviations
S
2. The master sends the 7-bit slave address followed by the
write bit (low).
START
P
R
STOP
READ
3. The addressed slave device asserts ACK on SDA.
W
A
N
WRITE
ACKNOWLEDGE
NO ACKNOWLEDGE
4. The master sends the command byte. The command byte
is identified by an MSB =0. (An MSB =1 indicates an
Extended Register Write. See next section.)
QUICK COMMAND
5. The slave asserts ACK on SDA.
This operation allows the master check if the slave is present on
the bus. This entails the following:
6. The master asserts a STOP condition on SDA to end the
transaction.
1. The master device asserts a start condition on SDA.
1
2
4
3
5
6
SLAVE
ADDRESS
COMMAND
BYTE
2. The master sends the 7-bit slave address followed by
the write bit (low).
S
W A
A
P
Figure 10. Command Byte Write
3. The addressed slave device asserts ACK on SDA.
The seven LSBs of the command byte are used to configure and
control the ADM1177. Details of the function of each bit are
provided in Table 6.
1
2
3
SLAVE
ADDRESS
S
W A
Figure 9. Quick Command
Table 6. Command Byte Operations
Bit Default Name
Function
C0
0
V_CONT
Set to convert voltage continuously. If readback is attempted before the first conversion is complete, the
ADM1177 will ACK and return all zeros in the returned data.
C1
C2
0
0
V_ONCE
I_CONT
Set to convert voltage once. Self-clears. I2C will NACK an attempted read until ADC conversion is complete.
Set to convert voltage continuously. If readback is attempted before the first conversion is complete, the
ADM1177 will ACK and return all zeros in the returned data.
Set to convert current once. Self-clears. I2C will NACK an attempted read until ADC conversion is complete.
Selects different internal attenuation resistor networks for voltage readback. A “0” in C4 selects a 14:1 voltage
divider. A “1”in C4 selects a 7:2 voltage divider. With an ADC full-scale of 1.902 V, the voltage at the VCC pin
for an ADC full-scale result is 26.63 V for VRANGE = 0 and 6.66 V for VRANGE = 1.
C3
C4
0
0
I_ONCE
VRANGE
C5
C6
0
0
N/A
Unused
STATUS_RD Status Read. When this bit is set the data byte read back from the ADM1177 will be the STATUS byte. This
contains the status of the device alerts. See Table14 for full details of the status byte.
Rev. PrD | Page 12 of 16
Preliminary Technical Data
ADM1177
WRITE EXTENDED BYTE
In this operation the master device writes to one of the three
extended registers of the slave device, as follows:
8. The master asserts a STOP condition on SDA to end the
transaction.
1
2
6
5
7 8
3
4
1. The master device asserts a start condition on SDA.
SLAVE
ADDRESS
REGISTER
ADDRESS
REGISTER
DATA
S
R A
A
N P
2. The master sends the 7-bit slave address followed by the
write bit (low).
Figure 11. Command Byte Write
3. The addressed slave device asserts ACK on SDA.
4. The master sends the register address byte. The MSB of
this byte is set to 1 to indicate an extended register write.
The two LSBs indicate which of the three extended
registers will be written to (see Table 7). All other bits
should be set to 0.
Table 8, Table 9, and give details of each extended register.
Table 7. Extended Register Addresses
A6 A5 A4 A3 A2 A1 A0 Extended Register
5. The slave asserts ACK on SDA.
6. The master sends the command byte. The command byte
is identified by an MSB = 0. (An MSB = 1 indicates an
Extended Register Write. See next section.)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
0
1
ALERT_EN
ALERT_TH
CONTROL
7. The slave asserts ACK on SDA.
Table 8. ALERT_EN Register Operations
Bit Default Name
Function
0
1
2
3
4
0
0
1
0
0
EN_ADC_OC1
EN_ADC_OC4
EN_HS_ALERT
Enabled if a single ADC conversion on the I channel has exceeded the threshold set in the ALERT_TH
register
Enabled if four consecutive ADC conversions on the I channel have exceeded the threshold set in the
ALERT_TH register
Enabled if the hotswap has either latched off, or entered a cool down cycle, because of an overcurrent
event
EN_OFF_ALERT Enable an ALERT if the HS operation is turned off by a transition which de-asserts the ON pin, or by an
operation which writes the SWOFF bit high.
CLEAR
Clears the ON_ALERT, HS_ALERT and ADC_ALERT status bits in the STATUS register. These may
immediately reset if the source of the alert has not been cleared, or disabled with the other bits in this
register. This bit self-clears to 0 after the STATUS register bits have been cleared.
Table 9. ALERT_TH Register Operations
Bit Default Function
7:0 FF
The ALERT_TH register sets the current level at which an alert will occur. Defaults to ADC full-scale. ALERT_TH 8-bit number
corresponds to the top 8-bits of the current channel data.
Table 10. CONTROL Register Operations
Bit
Default
Name
Function
0
0
SWOFF
Force hotswap off. Equivalent to de-asserting the ON pin.
Rev. PrD | Page 13 of 16
ADM1177
Preliminary Technical Data
READ VOLTAGE AND/OR CURRENT DATA BYTES
The ADM1177 can be set up to provide information in three
different ways (see Write Command Byte section above).
Depending on how the device is configured the following data
can be read out of the device after a conversion (or
conversions):
6.
The master receives the second data byte.
7.
The master asserts ACK on SDA.
8.
The master receives the third data byte.
The master asserts NO ACK on SDA.
9.
1.
Voltage and Current Readback.
10.
The master asserts a STOP condition on SDA and the
transaction ends.
The ADM1177 will digitize both voltage and current. Three
bytes will be read out of the device in the following format:
For the cases where the master is reading voltage only or
current only, only two data bytes will be read and events 7 and 8
above will not be required.
Table 11.
Byte Contents B7
B6
B5 B4 B3 B2 B1 B0
1
2
3
Voltage
MSBs
Current
MSBs
Voltage
LSBs
V11 V10 V9 V8 V7 V6 V5 V4
1
2
8
9 10
N P
3
4
5
6
7
I11
V3
I10
V2
I9
I8
I7
I6
I2
I5
I1
I4
I0
SLAVE
ADDRESS
S
R A
DATA 1 A DATA 2 A
DATA 3
V1 V0 I3
Figure 12. Three Byte Read fromADM1177
1
2
6
5
7 8
3
4
2.
Voltage Readback.
SLAVE
ADDRESS
REGISTER
ADDRESS
REGISTER
DATA
S
R A
A
N P
The ADM1177 will digitize voltage only. Two bytes will be read
out of the device in the following format:
Figure 13. Two Byte Read fromADM1177
Table 12.
Byte Contents
B7 B6 B5 B4 B3 B2 B1 B0
Voltage MSBs V11 V10 V9 V8 V7 V6 V5 V4
Voltage LSBs V3 V2 V1 V0
Read Status Register
1
2
A single register of status data can also be read from the
ADM1177.
0
0
0
0
1.
2.
The master device asserts a START condition on SDA.
3.
Current Readback.
The master sends the 7-bit slave address followed by
the read bit (high).
The ADM1177 will digitize current only. Two bytes will be read
out of the device in the following format:
3.
4.
5.
The addressed slave device asserts ACK on SDA.
The master receives the status byte.
Table 13.
Byte Contents
1
2
B7 B6 B5 B4 B3 B2 B1 B0
Current MSBs I11 I10 I9 I8 I7 I6
Current LSBs I3 I2 I1 I0
I5
0
I4
0
The master asserts ACK on SDA.
0
0
1
2
3
4
5
The following series of events occur when the master receives
three bytes (voltage and current data) from the slave device:
SLAVE
ADDRESS
S
R A
DATA 1 A
1.
2.
The master device asserts a START condition on SDA.
Figure 14. Status Read fromADM1177
The master sends the 7-bit slave address followed by
the read bit (high).
Table 14 shows the ADM1177 status registers in detail. Note
that bits 1, 3 and 5 are cleared by writing to bit 4 of the
ALERT_EN register (CLEAR).
3.
4.
5.
The addressed slave device asserts ACK on SDA.
The master receives the first data byte.
The master asserts ACK on SDA.
Rev. PrD | Page 14 of 16
Preliminary Technical Data
ADM1177
Table 14. Status Byte Operations
Bit Name
Function
0
1
ADC_OC
An ADC based overcurrent comparison has been detected on the last 3 conversions
ADC_ALERT An ADC based overcurrent trip has happened, which has caused the ALERT. Cleared by writing to bit 4 of the
ALERT_EN register.
2
HS_OC
The hotswap is off due to an analog overcurrent event. On parts which latch off, this will be the same as the HS_ALERT
status bit (if EN_HS_ALERT=1). On the retry parts this will indicate the current state—a 0 could indicate that the data
was read during a period when the device is retrying, or that it has successfully hotswapped by retrying after at least
one overcurrent timeout.
3
4
HS_ALERT
The hotswapper has failed since the last time this was reset. Cleared by writing to bit 4 of the ALERT_EN register.
OFF_STATUS The state of the ON pin. Set to 1 if the input pin is de-asserted. Can also be set to 1 by writing to the SWOFF bit of the
CONTROL register.
5
OFF_ALERT
An alert has been caused either by the ON pin or the SWOFF bit. Cleared by writing to bit 4 of the ALERT_EN register.
KELVIN SENSE RESISTOR CONNECTION
When using a low-value sense resistor for high current
measurement the problem of parasitic series resistance can
arise. The lead resistance can be a substantial fraction of the
rated resistance making the total resistance a function of lead
length. This problem can be avoided by using a Kelvin sense
connection. This type of connection separates the current path
through the resistor and the voltage drop across the resistor.
Figure 15 below shows the correct way to connect the sense
resistor between the VCC and SENSE pins of the ADM1177.
SENSE RESISTOR
CURRENT
FLOW FROM
SUPPLY
CURRENT
FLOW TO
LOAD
KELVIN SENSE TRACES
V
CC
SENSE
ADM1177
Figure 15. Kelvin Sense Connections
Rev. PrD | Page 15 of 16
ADM1177
Preliminary Technical Data
OUTLINE DIMENSIONS
0.122 (3.10)
0.114 (2.90)
10
6
5
0.199 (5.05)
0.187 (4.75)
0.122 (3.10)
0.114 (2.90)
1
PIN
1
0.0197 (0.50)
BSC
0.120 (3.05)
0.120 (3.05)
0.112 (2.85)
0.112 (2.85)
0.037 (0.94)
0.031 (0.78)
0.043 (1.10)
MAX
6o
0o
SEATING
PLANE
0.006 (0.15) 0.012 (0.30)
0.002 (0.05) 0.006 (0.15)
0.028 (0.70)
0.016 (0.40)
0.009 (0.23)
0.005 (0.13)
Figure 16. 10-Lead MSOP Package
(RM-10)
Dimensions shown in millimeters
ORDERING GUIDE
Model
Hotswap Retry Option
Brand Temperature Range
Package Description
Package Outline
RM-10
RM-10
ADM1177-1ARMZ-R7
ADM1177-2ARMZ-R7
1 Z = Pb-free part.
Automatic Retry Version
Latched Off Version
M5Y
M5Z
−40°C to +85°C
−40°C to +85°C
MSOP-10
MSOP-10
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
PR06047-0-5/06(PrD)
Rev. PrD | Page 16 of 16
相关型号：
©2020 ICPDF网 联系我们和版权申明