ADRV9029BBCZ_技术文档

Integrated, Quad RF Transceiver

with Observation Path

ADRV9029

Data Sheet

functions such as analog-to-digital converters (ADCs), digital-

to-analog converters (DACs), and general-purpose input/

outputs (GPIOs) that provide an array of digital control options

are also integrated.

FEATURES

4 differential transmitters

4 differential receivers

2 observation receivers with 2 inputs each

Center frequency: 75 MHz to 6000 MHz

Fully integrated DPD adaptation engine for power amplifier

linearization

To achieve a high level of RF performance, the transceiver

includes five fully integrated phase-locked loops (PLLs). Two

PLLs provide low noise and low power fractional-N RF

synthesis for the transmitter and receiver signal paths. A third

fully integrated PLL supports an independent local oscillator (LO)

mode for the observation receiver. The fourth PLL generates

the clocks needed for the converters and digital circuits, and a

fifth PLL provides the clock for the serial data interface.

Crest factor reduction engine

Maximum receiver bandwidth: 200 MHz

Maximum transmitter large signal bandwidth: 200 MHz

Maximum transmitter synthesis bandwidth: 450 MHz

Maximum observation receiver bandwidth: 450 MHz

Fully integrated independent fractional-N radio frequency

synthesizers

Fully integrated clock synthesizer

Multichip phase synchronization for all local oscillators and

baseband clocks

A multichip synchronization mechanism synchronizes the

phase of all LOs and baseband clocks between multiple

ADRV9029 chips. All voltage controlled oscillators (VCOs) and

loop filter components are integrated and adjustable through the

digital control interface.

Support for TDD and FDD applications

24.33 Gbps JESD204B/JESD204C digital interface

This device contains a fully integrated, low power digital

predistortion (DPD) adaptation engine for use in power

amplifier linearization. DPD enables use of high efficiency power

amplifiers, reducing the power consumption of base station radios

while also reducing the number of SERDES lanes necessary to

interface with baseband processors.

APPLICATIONS

3G/4G/5G TDD and FDD massive MIMO, macro and small cell

base stations

GENERAL DESCRIPTION

The low power crest factor reduction (CFR) engine of the

ADRV9029 reduces the peak to average ratio (PAR) of the

input signal, enabling higher efficiency transmit line ups while

reducing the processing load on baseband processors.

The ADRV9029 is a highly integrated, radio frequency (RF) agile

transceiver offering four independently controlled transmitters,

dedicated observation receiver inputs for monitoring each

transmitter channel, four independently controlled receivers,

integrated synthesizers, and digital signal processing functions

providing a complete transceiver solution. The device provides

the performance demanded by cellular infrastructure applications,

such as small cell base station radios, macro 3G/4G/5G systems,

and massive multiple in/multiple out (MIMO) base stations.

The serial data interface consists of four serializer lanes and four

deserializer lanes. The interface supports both the JESD204B and

JESD204C standards, operating at data rates up to 24.33 Gbps.

The interface also supports interleaved mode for lower

bandwidths, thus reducing the number of high speed data

interface lanes to one. Both fixed and floating-point data

formats are supported. The floating-point format allows

internal automatic gain control (AGC) to be invisible to the

demodulator device.

The receiver subsystem consists of four independent, wide

bandwidth, direct conversion receivers with wide dynamic

range. The four independent transmitters use a direct conversion

modulator resulting in low noise operation with low power

consumption. The device also includes two wide bandwidth,

time shared, observation path receivers with two inputs each for

monitoring transmitter outputs.

The ADRV9029 is powered directly from 1.0 V, 1.3 V, and

1.8 V regulators and is controlled via a standard serial

peripheral interface (SPI) serial port. Comprehensive power-

down modes are included to minimize power consumption in

normal use. The ADRV9029 is packaged in a 14 mm × 14 mm,

289-ball chip scale ball grid array (CSP_BGA).

The complete transceiver subsystem includes automatic and

manual attenuation control, dc offset correction, quadrature error

correction (QEC), and digital filtering, eliminating the need for

these functions in the digital baseband. Other auxiliary

Rev. 0

Document Feedback

Information furnished by Analog Devices is believed to be accurate and reliable. However, no

responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other

rights of third parties that may result from its use. Specifications subject to change without notice.

No license is granted by implication or otherwise under any patent or patent rights of Analog

Devices. Trademarks and registeredtrademarks are the property of their respective owners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Tel: 781.329.4700

Technical Support

www.analog.com

ADRV9029

Data Sheet

TABLE OF CONTENTS

Features.............................................................................................. 1

3800 MHz Band.......................................................................... 82

4800 MHz Band.......................................................................... 97

5700 MHz Band........................................................................ 112

Theory of Operation .................................................................... 127

General....................................................................................... 127

Transmitter ............................................................................... 127

Receiver ..................................................................................... 127

Observation Receiver............................................................... 127

Clock Input ............................................................................... 127

Synthesizers............................................................................... 128

SPI Interface.............................................................................. 128

GPIO_x Pins ............................................................................. 128

Auxiliary Converters ............................................................... 128

Digital Predistortion (DPD)................................................... 128

Crest Factor Reduction (CFR) ............................................... 131

JTAG Boundary Scan .............................................................. 131

Applications Information ........................................................... 132

Power Supply Sequence........................................................... 132

Data Interface ........................................................................... 132

Outline Dimensions..................................................................... 133

Ordering Guide ........................................................................ 133

Applications ...................................................................................... 1

General Description......................................................................... 1

Revision History ............................................................................... 2

Functional Block Diagram .............................................................. 3

Specifications .................................................................................... 4

Transmitters and Receivers......................................................... 4

Synthesizers, Auxiliary Converters, and Clock References.. 11

Digital Specifications ................................................................. 14

Power Supply Specifications..................................................... 15

Current Consumption............................................................... 16

Digital Interface and Timing Specifications........................... 17

Absolute Maximum Ratings ......................................................... 18

Junction Temperature ............................................................... 18

Reflow Profile.............................................................................. 18

Thermal Resistance.................................................................... 18

ESD Caution................................................................................ 18

Pin Configuration and Function Descriptions .......................... 19

Typical Performance Characteristics........................................... 24

75 MHz Band.............................................................................. 24

800 MHz Band............................................................................ 37

1800 MHz Band.......................................................................... 52

2600 MHz Band.......................................................................... 67

REVISION HISTORY

12/2020—Revision 0: Initial Version

Rev. 0 | Page 2 of 133

Data Sheet

ADRV9029

FUNCTIONAL BLOCK DIAGRAM

RX3, RX4, TX3, TX4, ORX3/ORX4

RX1, RX2, TX1, TX2, ORX1/ORX2

RX3+

RX3–

RX4+

RX4–

RX1+

RX1–

RX2+

RX2–

Rx1

Rx2

DECIMATION,

pFIR,

AGC,

DC-OFFSET,

QEC,

TUNING,

RSSI,

OVERLOAD

ADC

SERDOUTA±

SERDOUTB±

SERDOUTC±

SERDOUTD±

LO 1

LO 2

0°

90°

TX3+

TX3–

TX4+

TX4–

TX1+

TX1–

TX2+

TX2–

Tx1

Tx2

SYNCIN1±

SYNCIN2±

SYNCIN3±

DAC

JESD204B/

JESD204C

SERIAL

pFIR,

LO LEAKAGE,

QEC,

TUNING,

INTERPOLATION

LO 1

LO 2

CFR

DPD

0°

90°

INTERFACE

SERDINA±

SERDINB±

SERDINC±

SERDIND±

ORX3+

ORX3–

ORX4+

ORX4–

ORX2+

ORX2–

ORX1+

ORX1–

ORx1/ORx2

ADC

DECIMATION,

pFIR,

DC-OFFSET,

QEC,

TUNING,

OVERLOAD

SYNCOUT1±

SYNCOUT2±

0°

90°

LO 3

8

1

VDDA_1P8

GPIO_ANA_x

AUXADC_x

GPIO_x

GPIO

AUXILIARY ADC

AUXILIARY DAC

4

2

VDDA_1P3

VDDA_1P0

POWER

MANAGEMENT

3

19

VIF

VDIG_1P0

MICROPROCESSOR

CLOCK GENERATION

AND

SYNCHRONIZATION

DEVCLK±

SYSREF±

LO 3

RF SYNTHESIZER

SPI_CLK

SPI_EN

SPI_DO

SPI_DIO

SPI PORT

LO 1

LO 2

GPINT1

EXT_LO1±

EXT_LO2±

GPINT2

4

RXx_EN

CONTROL

INTERFACE

TXx_EN

4

ORX_CTRL_x

ADRV9029

RESET

TEST_EN

1

VDDA_1P8 REPRESENTS VCONV1_1P8, VCONV2_1P8, VANA1_1P8, VANA2_1P8, VANA3_1P8, VANA4_1P8, AND VJVCO_1P8.

2

VDDA_1P3 REPRESENTS VANA1_1P3, VANA2_1P3, VCONV1_1P3, VCONV2_1P3, VRFVCO1_1P3, VRFVCO2_1P3, VAUXVCO_1P3, VCLKVCO_1P3,

VRFSYN1_1P3, VRFSYN2_1P3, VCLKSYN_1P3, VAUXSYN_1P3, VRXLO_1P3, AND VTXLO_1P3.

3

VDDA_1P0 REPRESENTS VJSYN_1P0, VDES_1P0, VTT_DES, AND VSER_1P0.

Figure 1.

Rev. 0 | Page 3 of 133

ADRV9029

Data Sheet

SPECIFICATIONS

Electrical characteristics at ambient temperature range. Power supplies are as follows: VDDA_1P8 = 1.8 V, VIF = 1.8 V, VDDA_1P3 =

1.3 V, VDDA_1P0 = 1.0 V, and VDIG_1P0 = 1.0 V. VDDA_1P8 represents VCONV1_1P8, VCONV2_1P8, VANA1_1P8, VANA2_1P8,

VANA3_1P8, VANA4_1P8, and VJVCO_1P8. VDDA_1P3 represents VANA1_1P3, VANA2_1P3, VCONV1_1P3, VCONV2_1P3,

VRFVCO1_1P3, VRFVCO2_1P3, VAUXVCO_1P3, VCLKVCO_1P3, VRFSYN1_1P3, VRFSYN2_1P3, VCLKSYN_1P3,

VAUXSYN_1P3, VRXLO_1P3, and VTXLO_1P3. VDDA_1P0 represents VJSYN_1P0, VDES_1P0, VTT_DES, and VSER_1P0. All RF

specifications are based on measurements that include printed circuit board (PCB) and matching circuit losses, unless otherwise noted.

Device configuration profile: Receiver = 200 MHz bandwidth, I/Q rate = 245.76 MHz, transmitter = 200 MHz large signal bandwidth

plus 450 MHz synthesis bandwidth, I/Q rate = 491.52 MHz, observation receiver (OR_X) = 450 MHz bandwidth, I/Q rate = 491.52 MHz,

device clock = 245.76 MHz, unless otherwise noted. Characterization at 75 MHz followed this profile: Receiver = 62.5 MHz bandwidth,

I/Q rate = 76.8 MHz, transmitter = 62.5 MHz large signal bandwidth plus 141 MHz synthesis bandwidth, I/Q rate = 153.6 MHz,

observation receiver = 141 MHz bandwidth, I/Q rate = 153.6 MHz, device clock = 153.6 MHz.

Note: if signals are placed outside of the primary bandwidth, degradation in linearity, image rejection, and flatness may be observed.

TRANSMITTERS AND RECEIVERS

Table 1.

Parameter

Symbol

Min Typ

Max Unit

Test Conditions/Comments

TRANSMITTERS

Tx

Center Frequency

75

6000 MHz

Tx Synthesis Bandwidth

Tx Large Signal Bandwidth

Peak-to-Peak Gain Deviation

450

200

MHz

dB

Zero intermediate frequency (IF) mode

450 MHz bandwidth, includes compensation by

programmable finite impulse response (FIR) filter

Any 20 MHz bandwidth span, includes

compensation by programmable FIR filter (pFIR)

450 MHz bandwidth

0 dBFS, 1 MHz signal input, 50 Ω load, 0 dB

transmitter attenuation

1.0

0.1

1

dB

Deviation from Linear Phase

Maximum Output Power

Degrees

75 MHz

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Power Control Range

Power Control Resolution

Attenuation Accuracy

Integral Nonlinearity (Gain)

7.0

6.7

6.6

6.3

6.4

6.1

6.4

32

dBm

dB

0.05

dB

INL

0.1

dB

Valid over full power control range for any 4 dB

step

Differential Nonlinearity (Gain)

DNL

0.04

dB

Monotonic

Output Power Temperature

Slope

−4.5

mdB/°C

Valid over full power control range

LO Delay Temperature Slope

1.05

ps/°C

Valid over full power control range

20 MHz LTE at −12 dBFS

Adjacent Channel Leakage Power

Ratio (ACLR) Long Term

Evolution (LTE)

75 MHz

−64

−68

−67

−66

−65

dB

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Rev. 0 | Page 4 of 133

Data Sheet

ADRV9029

Parameter

Symbol

Min Typ

−154.5

Max Unit

dBFS/Hz

Test Conditions/Comments

In Band Noise Floor

0 dB attenuation; in band noise falls 1 dB for

each decibel of attenuation for attenuation

settings between 0 dB and 20 dB

Interpolation Images

−76

dBc

Tx to Tx Isolation: All Tx Output

Effects on All Other Tx Outputs

800 MHz

1800MHz

78

77

71

70

65

dB

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Image Rejection

Within 200 MHz Large Signal

Bandwidth

QEC active up to 20 dB of attenuation,

continuous wave tone swept across the large

signal bandwidth

75 MHz

80

76

75

73

65

64

61

dB

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Beyond Large Signal

Bandwidth

Assumes that distortion power density is 25 dB

below desired power density

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

40

38

34

37

50

dB

Ω

5700 MHz

Output Impedance

Z_OUT

Differential—nominal

Maximum Output Load Voltage

Standing Wave Ratio

VSWR

3

Maximum value to ensure adequate calibration

Output Return Loss

10

dB

Output Third-Order Intercept

Point

OIP3

0 dB transmitter attenuation

75 MHz

800 MHz

30

29

28

26.5

29

27

dBm

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Carrier Leakage

With LO leakage correction active, 0 dB

transmitter attenuation, scales decibel for

decibel with attenuation

Carrier Offset from LO

75 MHz LO

800 MHz LO

−84

−83

−84

−83

dBFS/MHz

1800 MHz LO

2600 MHz LO

3800 MHz LO

4800 MHz LO

5700 MHz LO

Rev. 0 | Page 5 of 133

ADRV9029

Data Sheet

Parameter

Symbol

Min Typ

Max Unit

Test Conditions/Comments

Carrier on the LO

−71

dBFS/MHz Measured using an LTE 20 MHz signal

Error Vector Magnitude

EVM

PLL optimized for narrow-band noise, measured

using LTE 20 MHz signal

75 MHz LO

800 MHz LO

1800 MHz LO

2600 MHz LO

3800 MHz LO

4800 MHz LO

5700 MHz LO

0.25

0.38

0.60

0.44

0.53

0.63

0.84

%

50 kHz PLL bandwidth

500 kHz PLL bandwidth

200 kHz PLL bandwidth

400 kHz PLL bandwidth

500 kHz PLL bandwidth

Transmitter Time Division Duplex

Time from SPI_EN Going High

to Change in Tx Attenuation

Time Between Consecutive

Microattenuation Steps

TDD

t_SCH

12

20

ns

t_ACH

A large change in attenuation can be

segmented into a series of smaller attenuation

changes

Attenuation Overshoot During

Transition

Change in Attenuation per

Microstep

0.1

dB

RECEIVERS

Rx

Center Frequency

Gain Range

75

30

6000 MHz

dB

Attenuation Accuracy

Analog Gain Step

0.5

1

0.1

−6.4

1.0

dB

mdB/°C

ps/°C

Attenuator steps from 0 dB to 6 dB

Attenuator steps from 6 dB to 30 dB

Residual Gain Step Error

Gain Temperature Slope

Internal LO Delay Temperature

Slope

Frequency Response

Peak-to-Peak Gain Deviation

1

dB

200 MHz bandwidth, includes compensation by

programmable FIR filter

Any 20 MHz span, includes compensation by

programmable FIR filter

0.2

Rx Bandwidth

Rx Alias Band Rejection

Maximum Useable Input Level

200

MHz

dB

Zero IF mode

Due to digital filters

This continuous wave signal level corresponds

to the input power that produces −2 dBFS at the

digital output with 0 dB channel attenuation

80

P_HIGH

75 MHz

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

−11.7

−12.4

−12.7

−11.9

−11.0

−12.0

−11.1

dBm

Maximum Source VSWR

Input Impedance

Input Port/Return Loss

3

Z_IN

100

10

Ω

dB

Differential

Unmatched differential port return loss

Rev. 0 | Page 6 of 133

Data Sheet

ADRV9029

Parameter

Symbol

Min Typ

Max Unit

Test Conditions/Comments

Noise Figure

NF

0 dB receiver attenuation, measured at single-

ended input, matching circuit included

75 MHz

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

12

11

dB

11.5

11.9

12.8

13.3

14.5

1.5

5700 MHz

Noise Figure Ripple

At band edge

Second-Order Input

IIP2

0 dB attenuation, complex

Intermodulation Intercept Point

75 MHz

70

65

62

58

dBm

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Wideband Third-Order Input

Intermodulation Intercept Point,

Difference Product

IIP3_{WB_DIFF}

Two tones near the band edge, test condition:

P

_HIGH− 9 dB/tone

75 MHz

14

15

17

18

dBm

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Midband Third-Order Input

Intermodulation Intercept Point,

Difference Product

IIP3_{MB_DIFF}

Two tones near the middle of the band; test

condition: P_HIGH− 9 dB/tone

75 MHz

20

18

22

21

22

20

dBm

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Wideband Third-Order Input

Intermodulation Intercept Point,

Sum Product

IIP3_WB

_

Two tones approximately bandwidth ÷ 6 offset

from the LO; test condition: P_HIGH– 9 dB/tone

SUM

75 MHz

15

17

20

23

20

dBm

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Second-Order Harmonic

Distortion

Maximum Input

HD2_MAX

HD2

−72

−75

dBc

P

_HIGHcontinuous wave signal, harmonic

distortion tones falling within 100 MHz of the LO

_HIGH− 3 dB continuous wave signal, harmonic

distortion tones falling within 100 MHz of the LO

Recommended Input

P

Rev. 0 | Page 7 of 133

ADRV9029

Data Sheet

Parameter

Symbol

Min Typ

Max Unit

Test Conditions/Comments

Third-Order Harmonic Distortion

Maximum Input

HD3_MAX

HD3

−66

−72

dBc

P

_HIGHcontinuous wave signal, harmonic

distortion tones falling within 100 MHz of the LO

_HIGH− 3 dB continuous wave signal, harmonic

distortion tones falling within 100 MHz of the LO

Recommended Input

P

Fourth-Order Harmonic Distortion

Maximum Input

HD4_MAX

HD4

−90

dBc

P

_HIGHcontinuous wave signal, harmonic

distortion tones falling within 100 MHz of the LO

_HIGH− 3 dB continous wave signal, harmonic

distortion tones falling within 100 MHz of the LO

Recommended Input

P

Fifth-Order Harmonic Distortion

Maximum Input

HD5_MAX

HD5

−87

−90

75

dBc

dB

P

_HIGHcontinuous wave signal, harmonic distortion

tones falling within 100 MHz of the LO

P_HIGH− 3 dB continuous wave signal, harmonic

Recommended Input

distortion tones falling within 100 MHz of the LO

QEC active, within 200 MHz receiver bandwidth

Image Rejection

Rx to Rx Signal Isolation

75 MHz

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

80

75

70

65

62

60

−95

dB

dBm

Rx Band Spurs Referenced to RF

Input at Maximum Gain

No more than one spur at this level per 10 MHz

of receiver bandwidth; excludes harmonics of

the reference clock

Spurious-Free Dynamic Range

SFDR

81

dBc

P_HIGHcontinuous wave signal anywhere inside

the band 20 MHz, excludes harmonic

distortion products

Rx Input LO Leakage at Maximum

Gain

Leakage decreased decibel for decibel with

attenuation for first 12 decibels

75 MHz

−68

−65

−58

−54

dBm

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Tx to Rx Signal Isolation: All Tx

Output Effects on all Rx Inputs

75 MHz

800 MHz

1800 MHz

2600 MHz

3800 MHz

80

75

65

dB

4800 MHz

5700 MHz

OBSERVATION RECEIVERS

Center Frequency

Gain Range

ORx

75

30

6000 MHz

dB

Attenuation Accuracy

Analog Gain Step

0.5

1

dB

Attenuator steps from 0 dB to 6 dB

Attenuator steps from 6 dB to 30 dB

Rev. 0 | Page 8 of 133

Data Sheet

ADRV9029

Parameter

Symbol

Min Typ

Max Unit

Test Conditions/Comments

Peak-to-Peak Gain Deviation

1

dB

450 MHz RF bandwidth, compensation by

programmable FIR filter

0.1

1

dB

Any 20 MHz bandwidth span, compensation by

programmable FIR filter

450 MHz RF bandwidth

Deviation from Linear Phase

ORx Bandwidth

Degrees

MHz

450

ORx Alias Band Rejection

Maximum Useable Input Level

60

dB

Due to digital filters

P_HIGH

This continuous wave signal level corresponds

to the input power that produces −2 dBFS at the

digital output with 0 dB channel attenuation

75 MHz

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Input Impedance

Input Source VSWR

Input Port Return Loss

Integrated Noise

450 MHz Bandwidth

−11.4

dBm

Ω

−12.7

−11.5

−10.6

−12.0

−11.3

−9.5

Z_IN

100

Differential

3

10

dB

Unmatched differential port return loss

−58.5

−57.5

dBFS

Sample rate at maximum value integrated from

500 kHz to 225 MHz, no input signal

Sample rate at maximum value integrated from

500 kHz to 245.76 MHz, no input signal

491.52 MHz Bandwidth (Nyquist)

Second-Order Input Intermodu-

lation Intercept Point

IIP2

Maximum observation receiver gain; test

condition: P_HIGH− 11 dB/tone

75 MHz

55

53

55

48

45

55

dBm

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Third-Order Input Intermodulation

Intercept Point

IIP3

Maximum observation receiver gain; test

condition: P_HIGH− 11 dB/tone

Narrow Band

IIP3_NB

IM3 product < 130 MHz at baseband; test

condition: P_HIGH− 11 dB/tone, 491.52 MSPS

75 MHz

800 MHz

11

13.6

15

16.5

18

dBm

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Wide Band

18

IIP3_WB

IM3 products > 130 MHz at baseband; test

condition: P_HIGH−11 dB/tone, 491.52 MSPS

800 MHz

7.8

13

11

13

14

dBm

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Rev. 0 | Page 9 of 133

ADRV9029

Data Sheet

Parameter

Symbol

Min Typ

Max Unit

Test Conditions/Comments

Third-Order Intermodulation

Product

IM3

Narrow Band

IM3_NB

IM3 product < 130 MHz at baseband; test

condition: two tones, each at P_HIGH− 11 dB,

491.52 MSPS

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Wide Band

−74

−79

−78.6

−80.4

−79.8

−76

dBc

IM3_WB

IM3 product > 130 MHz at baseband; test

condition: two tones, each at P_HIGH− 11 dB,

491.52 MSPS

800 MHz

−62.4

−70

−67.6

−70.4

−69.8

−66

dBc

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Fifth-Order Intermodulation

Product

IM5

Narrow Band

IM5_NB

IM5 product < 130 MHz at baseband; test

condition: two tones, each at P_HIGH− 11 dB,

491.52 MSPS

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Wide Band

−83

−87

−84

−80

−78

−81

dBc

IM5_WB

IM5 product > 130 MHz at baseband; test

condition:two tones, each at P_HIGH− 11 dB,

491.52 MSPS

800 MHz

−83

−96

−85

−80

−77

−85

dBc

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Seventh-Order Intermodulation

Product

IM7

Narrow Band

IM7_NB

IM7 product < 130 MHz at baseband; test

condition: two tones, each at P_HIGH− 11 dB,

491.52 MSPS

800 MHz

−74

−78

−75

−73

−78

−75

dBc

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Rev. 0 | Page 10 of 133

Data Sheet

ADRV9029

Parameter

Symbol

Min Typ

Max Unit

Test Conditions/Comments

Wide Band

IM7_WB

IM7 product > 130 MHz at baseband; test

condition: two tones, each at P_HIGH− 11 dB,

491.52 MSPS

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

−83

−82

−83

−85

−81

64

dBc

dB

5700 MHz

Spurious-Free Dynamic Range

SFDR

HD2

Nonintermodulation related spurs; does not in-

clude harmonic distortion; input set at P_HIGH− 8 dB

Input set at P_HIGH− 8 dB

In-band harmonic distortion falls within

100 MHz

Out of band harmonic distortion falls within

225 MHz

Second-Order Harmonic Distortion

In Band

−80

−73

dBc

Out of Band

Third-Order Harmonic Distortion

In Band

Out of Band

HD3

Input set at P_HIGH− 8 dB

−70

−65

75

dBc

dB

Harmonic distortion falls within 100 MHz

Harmonic distortion falls within 225 MHz

After online tone calibration, QEC active

Image Rejection

Tx to ORx Signal Isolation: All Tx

Output Effects on all ORx Inputs

75

dB

SYNTHESIZERS, AUXILIARY CONVERTERS, AND CLOCK REFERENCES

Table 2.

Parameter

Symbol

Min Typ

Max Unit

Test Conditions/Comments

LO1 and LO2 SYNTHESIZER

Frequency Step

LO1, LO2

7.3

Hz

1.6 GHz to 3.2 GHz, 245.76 MHz phase

frequency detector (PFD) frequency

Spectral Purity

−80

dBc

Integrated Phase Noise

Integrated from 1 kHz to 100 MHz

Narrow Bandwidth

Optimized

PLL bandwidth optimized to minimize

phase noise at offsets > 200 kHz

800 MHz

0.12

0.27

0.66

0.53

0.91

1.57

°rms

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Wide Bandwidth

Optimized

PLL bandwidth optimized for integrated

phase noise and phase noise at offsets

> 1 MHz and phase noise at offsets > 1 MHz

800 MHz

0.07

0.11

0.17

0.26

0.30

0.42

°rms

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Spot Phase Noise: Narrow

Band

PLL bandwidth optimized to minimize

phase noise at offsets > 200 kHz

800 MHz LO1 and LO2

100 kHz Offset

1 MHz Offset

−115

−141

−162

dBc/Hz

10 MHz Offset

Rev. 0 | Page 11 of 133

ADRV9029

Data Sheet

Parameter

Symbol

Min Typ

Max Unit

dBc/Hz

Test Conditions/Comments

1800 MHz LO1 and LO2

100 kHz Offset

200 kHz Offset

400 kHz Offset

600 kHz Offset

800 kHz Offset

1.2 MHz Offset

1.8 MHz Offset

6 MHz Offset

−107

−115

−123

−128

−131

−136

−140

−151

−156

dBc/Hz

10 MHz Offset

2600 MHz LO1 and LO2

100 kHz Offset

1 MHz Offset

−97

−124

−150

dBc/Hz

10 MHz Offset

3800 MHz LO1 and LO2

100 kHz Offset

1 MHz Offset

−100

−126

−149

dBc/Hz

10 MHz Offset

4800 MHz LO1 and LO2

100 kHz Offset

1 MHz Offset

−94

−120

−145

dBc/Hz

10 MHz Offset

5700 MHz LO1 and LO2

100 kHz Offset

1 MHz Offset

−89

−115

−141

dBc/Hz

10 MHz Offset

Spot Phase Noise: Wideband

PLL bandwidth optimized for integrated

phase noise and phase noise at offsets

> 1 MHz

800 MHz LO1 and LO2

100 kHz Offset

1 MHz Offset

10 MHz Offset

1800 MHz LO1 and LO2

100 kHz Offset

1 MHz Offset

−114

−141

−162

dBc/Hz

−112

−133

−156

dBc/Hz

10 MHz Offset

2600 MHz LO1 and LO2

100 kHz Offset

1 MHz Offset

−112

−120

−149

dBc/Hz

10 MHz Offset

3800 MHz LO

100 kHz Offset

1 MHz Offset

10 MHz Offset

−104

−125

−149

dBc/Hz

4800 MHz LO1 and LO2

100 kHz Offset

1 MHz Offset

−106

−117

−144

dBc/Hz

10 MHz Offset

5700 MHz LO1 and LO2

100 kHz Offset

1 MHz Offset

−104

−112

−140

dBc/Hz

10 MHz Offset

Rev. 0 | Page 12 of 133

Data Sheet

ADRV9029

Parameter

Symbol

Min Typ

Max Unit

Test Conditions/Comments

AUXILIARY SYNTHESIZER

Frequency Step

LO3

1.8

Hz

1.625 GHz to 3.25 GHz, 61.44 MHz PFD

frequency

Spectral Purity

−65

dBc

|f_RFLO− f_AUXLO| > 15 MHz

Integrated Phase Noise

Integrated from 1 kHz to 100 MHz, PLL

bandwidth optimized for integrated phase

noise

800 MHz LO3

1800 MHz LO3

2600 MHz LO3

3800 MHz LO3

4800 MHz LO3

5700 MHz LO3

Spot Phase Noise

800 MHz LO3

0.18

0.22

0.46

0.43

0.70

1.12

°rms

100 kHz Offset

1 MHz Offset

10 MHz Offset

−112

−121

−141

dBc/Hz

1800 MHz LO3

100 kHz Offset

1 MHz Offset

−110

−120

−134

dBc/Hz

10 MHz Offset

2600 MHz LO3

100 kHz Offset

1 MHz Offset

−103

−114

−132

dBc/Hz

10 MHz Offset

3800 MHz LO3

100 kHz Offset

1 MHz Offset

−104

−114

−128

dBc/Hz

10 MHz Offset

4800 MHz LO3

100 kHz Offset

1 MHz Offset

−100

−110

−127

dBc/Hz

10 MHz Offset

5700 MHz LO3

100 kHz Offset

1 MHz Offset

−95

−106

−126

dBc/Hz

10 MHz Offset

LO PHASE SYNCHRONIZATION

Initial Phase Sync Accuracy

CLOCK SYNTHESIZER

4915.2 MHz Sample Clock

Integrated Phase Noise

0.9

ps

0.69

°rms

1 kHz to 10 MHz, PLL bandwidth optimized

for integrated phase noise

Spot Phase Noise

PLL bandwidth optimized for integrated

phase noise

100 kHz Offset

1 MHz Offset

10 MHz Offset

−96

−113

−140

dBc/Hz

3932.16 MHz Sample Clock

Integrated Phase Noise

0.89

°rms

1 kHz to 10 MHz, PLL bandwidth optimized to

minimize phase noise at offsets >200 kHz

Rev. 0 | Page 13 of 133

ADRV9029

Data Sheet

Parameter

Symbol

Min Typ

Max Unit

Test Conditions/Comments

Spot Phase Noise

PLL bandwidth optimized to minimize

phase noise at offsets >200 kHz

100 kHz Offset

1 MHz Offset

10 MHz Offset

−91

−120

−143

dBc/Hz

REFERENCE CLOCK

(DEV_CLK INPUT SIGNAL)

DEV_CLK+,

DEV_CLK−

Frequency Range

Signal Level (Differential)

15

0.2

1000 MHz

1.0 V p-p

AC-coupled, common-mode voltage

internally supplied; for optimal spurious

performance and to meet the specified PLL

performance parameters, use a 1 V p-p input

clock

SYSTEM REFERENCE INPUTS

SYSREF+,

SYSREF−

Logic Compliance

Differential Input Voltage

Input Common-Mode

Voltage

LVDS/LVPECL

400 800

0.675

1800 mV p-p External 100 Ω differential termination

2.0

V

Input Resistance (Differential)

Input Capacitance

(Differential)

18

1

kΩ

pF

AUXILIARY CONVERTERS

ADC

Resolution

10

Bits

Input Voltage

Minimum

Maximum

0.05

0.95

V

AUXDAC_0

Resolution

12

Bits

Output Voltage

Minimum

Maximum

0.2

V

VDDA_1P8 − 0.25

AUXDAC_1 To AUXDAC_7

Resolution

12

Bits

Output Voltage

Minimum

0.1

V

Maximum

Drive Capability

VDDA_1P8 − 0.1

10

V

mA

DIGITAL SPECIFICATIONS

Table 3.

Parameter

Min

Typ

Max

Unit Test Conditions/Comments

DIGITAL SPECIFICATIONS—

SINGLE-ENDED SIGNALS

Applies to the following pins:

GPIO_x, GPINTx, TXx_EN,

RXx_EN, ORX_CTRL_x, TEST_EN,

RESET, SPI_EN, SPI_CLK, SPI_DO,

and SPI_DIO

Logic Inputs

Input Voltage

High Level

Low Level

VIF × 0.65

−0.30

VIF + 0.18

VIF × 0.35

V

Rev. 0 | Page 14 of 133

Data Sheet

ADRV9029

Parameter

Input Current

High Level

Min

Typ

Max

Unit Test Conditions/Comments

−10

+10

μA

Low Level

Logic Outputs

Output Voltage

High Level

VIF − 0.45

V

Low Level

0.45

V

Drive Capability

10

mA

DIGITAL SPECIFICATIONS—DIFFERENTIAL SIGNALS

Applies to the SYNCINx pins

and the SYNCOUTx pins

Logic Inputs

Input Voltage Range

825

1675

+100

mV

Each differential input in the

pair

Input Differential Voltage Threshold

Receiver Differential Input Impedance

−100

mV

Ω

100

Internal termination enabled

Logic Outputs

Output Voltage

High

1375

mV

Low

Differential

Offset

1025

225

1200

DIGITAL SPECIFICATIONS—VDDA_1P8

REFERENCED SIGNALS

Applies to the GPIO_ANA_x pins

Logic Inputs

Input Voltage

High Level

VDDA_1P8 × 0.65

−0.30

VDDA_1P8 + 0.18

VDDA_1P8 × 0.35

V

Low Level

Input Current

High Level

Low Level

−10

+10

μA

Logic Outputs

Output Voltage

High Level

VDDA_1P8 − 0.45

V

Low Level

0.45

V

Drive Capability

10

mA

POWER SUPPLY SPECIFICATIONS

Table 4. Power Supply Voltages

Parameter

Min

Typ

Max

Unit

SUPPLY CHARACTERISTICS

VDDA_1P0 Supply

VDIG Supply

VDDA_1P3 Supply

VDDA_1P8 Supply

VIF Supply

0.95

1.235

1.71

1.0

1.3

1.8

1.05

1.365

1.89

V

Rev. 0 | Page 15 of 133

ADRV9029

Data Sheet

CURRENT CONSUMPTION

In Table 5, Table 6, and Table 7, the first row contains the data for the UC13-NLS profile and subsequent rows provide UC13-NLS

profile details. Note that all current measurements reported in Table 5, Table 6, and Table 7 are obtained at room temperature without a

heat sink.

TDD Operation—Four Receiver Channels Enabled

Maximum gain and typical values.

Table 5.

Supply (A)

Profile Conditions

1.0 V 1.3 V 1.8 V Total Average Power (W) 75% Tx, 25% Rx Average Power (W)

1.181 2.003 0.217 4.19 5.01

USE CASE UC13-NLS (16 BITS)

245.76 MSPS Tx/ORx Data Rate

122.88 MSPS Rx Data Rate

245.76 MHz Device Clock

TDD Operation—Four Transmitter and One Observation Receiver Channels Enabled

Maximum gain, 0 dB attenuation, typical values.

Table 6.

Supply (A)

Profile Conditions

1.0 V 1.3 V 1.8 V Total Average Power (W) 75% Tx, 25% Rx Average Power (W)

1.419 2.084 0.633 5.28 5.01

USE CASE UC13-NLS (16 BITS)

245.76 MSPS Tx/ORx Data Rate

122.88 MSPS Rx Data Rate

245.76 MHz Device Clock

FDD Operation—LO1 and LO2, Four Receiver, Four Transmitter, and One Observation Receiver Channels Enabled

Maximum gain, 0 dB attenuation, typical values.

Table 7.

Supply (A)

Profile Conditions

1.0 V 1.3 V 1.8 V

Total Average Power (W)

USE CASE UC13-NLS (16 BITS)

245.76 MSPS Tx/ORx Data Rate

122.88 MSPS Rx Data Rate

245.76 MHz Device Clock

1.664 2.929 0.762

6.86

Rev. 0 | Page 16 of 133

Data Sheet

ADRV9029

DIGITAL INTERFACE AND TIMING SPECIFICATIONS

Table 8.

Parameter

Symbol Min

Typ Max

Unit

Test Conditions/Comments

SERIAL PERIPHERAL INTERFACE (SPI) TIMING

SPI_CLK Period

SPI_CLK Pulse Width

SPI_EN Setup to First SPI_CLK Rising Edge

Last SPI_CLK Falling Edge to SPI_EN Hold

SPI_DIO Data Input Setup to SPI_CLK

SPI_DIO Data Input Hold to SPI_CLK

SPI_CLK Falling Edge to Output Data Delay

t_CP

t_MP

t_SC

t_HC

t_S

t_H

t_CO

t_HZM

40

10

4

ns

0

4

0

10

t_H

8

t_CO

3- or 4-wire mode

Bus Turnaround Time After Baseband Processor Drives

Last Address Bit

Bus Turnaround Time After ADRV9029 Drives Last

Address Bit

t_HZS

0

t_CO

ns

DIGITAL TIMING

TXx_EN Pulse Width

RXx_EN Pulse Width

ORX_CTRL_x Pulse Width

TXx_EN to Valid Data

RXx_EN to Valid Data

ORX_CTRL_x to Valid Data

JESD204B/JESD204C DATA OUTPUT TIMING

Unit Interval

Data Rate per Channel (No Return to Zero (NRZ))

Rise Time

10

μs

2

3

UI

41.1

3000

17

333

ps

24330.24 Mbps

t_R

t_F

20

ps

20% to 80% in 100 Ω load

AC-coupled

Fall Time

17

Output Common-Mode Voltage

Differential Output Voltage

Short-Circuit Current

Differential Termination Impedance

SYSREF Input Signal Setup Time to DEV_CLK Input

Signal

V_CM

V_DIFF

I_DSHORT

Z_RDIFF

t_S

0

1.8

1050

+100

V

475

−100

80

mV p-p

mA

Ω

100 120

200

ps

SYSREF Input Signal Hold Time to DEV_CLK Input

Signal

t_H

200

ps

JESD204B/C DATA INPUT TIMING

Unit Interval

Data Rate per Channel (NRZ)

Input Common-Mode Voltage

Termination Voltage = 1.0 V

UI

41.1

3000

0.05

720

333

ps

24330.24 Mbps

1.65

1200

V_CM

V_TT

V

mV

AC-coupled

DC-coupled (not

recommended)

Differential Input Voltage

V_TTSource Impedance

Differential Termination Impedance

V_TT

V_DIFF

Z_TT

Z_RDIFF

110

80

1050

30

100 120

mV

Ω

7.5

AC-Coupled

DC-Coupled

0.95

1.05

V

Rev. 0 | Page 17 of 133

ADRV9029

Data Sheet

ABSOLUTE MAXIMUM RATINGS

Table 9.

Table 10. Acceleration Factors for High Temperature Operation

Parameter

Rating

Operating Junction

Temperature (°C)

Acceleration Factor

VDDA_1P8 to VSSA

VDDA_1P3 to VSSA

VDDA_1P0, VDIG_1P0 to VSSD, VSSA

VIF Referenced Logic Inputs and

Outputs to VSSD

JESD204B/JESD204C Logic Outputs to

VSSA

JESD204B/JESD204C Logic Inputs to

VSSA

Input Current to Any Pin Except Supplies

Maximum Input Power into RF Ports

−0.3 V to +2.2 V

−0.2 V to +1.5 V

−0.2 V to +1.2 V

−0.3 V to VIF + 0.3 V

125

120

115

110

105

100

95

3.75

2.44

1.57

1.00

0.63

0.39

0.24

0.14

−0.3 V to VSER_1P0

−0.3 V to VDES_1P0

10 mA

See Table 11 for limits

vs. survival time

260°C

90

Table 11. Maximum Input Power into RF Ports vs. Lifetime

RF Port Input Power,

Continuous Wave

Signal (dBm)

Lifetime

Reflow Temperature

Junction Temperature Range¹

Storage Temperature Range

Gain = −30 dB

Gain = 0 dB

>10 years

20,000 hours

14 hours

110 minutes

60 minutes

−40°C to +110°C

−65°C to +150°C

7

>10 years

>7 years

10

20

23

25

¹The maximum junction temperature for continuous operation is 110°C. See

the Junction Temperature section for more details.

Stresses at or above those listed under Absolute Maximum

Ratings may cause permanent damage to the product. This is a

stress rating only; functional operation of the product at these

or any other conditions above those indicated in the

operational section of this specification is not implied.

Operation beyond the maximum operating conditions for

extended periods may affect product reliability.

REFLOW PROFILE

The ADRV9029 reflow profile is in accordance with the JEDEC

JESD20 criteria for lead-free (Pb-free) devices. The maximum

reflow temperature is 260°C.

THERMAL RESISTANCE

JUNCTION TEMPERATURE

Thermal resistance values specified in Table 12 are calculated

based on JEDEC specifications and should be used in compliance

with JESD51-2. Note that using enhanced heat removal techniques

(PCB, heat sink, airflow, and so forth) improves thermal resistance.

The maximum junction temperature for continuous operation

is 110°C. Although operation up to 125°C is supported,

specification compliance is only guaranteed up to 110°C. To

avoid a reduction in operating lifetime by operating at

temperatures greater than 110°C, the device must operate at a

temperature less than 110°C for a period determined by the

following equation:

Table 12. Thermal Resistance Values

Package Type

θ_JA

θ_JCTOP

θ_JBψ_JC

ψ_JBUnit

3.4 (°C/W)

BC-289-6

14.8

0.03

3.4 0.02

t

_{UNITS < 110}= (AF_{T > 110}− 1)/(1 − AF_{T < 110})

ESD CAUTION

where:

AF is the acceleration factor.

AF_{T > 110}and AF_{T < 110}are acceleration factors obtained from

Table 10.

For example, if the device operates at 125°C for 1 hour,

expected device lifetime is maintained if the device operates at

100°C for 4.5 hours to offset the time operating above 110°C.

Rev. 0 | Page 18 of 133

Data Sheet

ADRV9029

PIN CONFIGURATION AND FUNCTION DESCRIPTIONS

ADRV9029

TOP VIEW

(Not to Scale)

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

VTXLO_

1P3

VRXLO_

1P3

A

B

C

D

E

F

VSSA

TX3+

TX3–

VSSA

TX2+

TX2–

VSSA

VAUXVCO_

1P0

VANA3_

1P8

VANA2_

1P8

RX3–

RX3+

VSSA

NIC

VSSA

RX2+

RX2–

VSSA

VAUXSYN_

1P3

VAUXVCO_

1P3

GPIO_

ANA_7

GPIO_

ANA_6

GPIO_

ANA_1

GPIO_

ANA_0

DEVCLK+ DEVCLK–

SYSREF+ SYSREF–

VSSA

RBIAS

VANA2_

1P3

VANA1_

1P3

VSSA

AUXADC_3 EXT_LO2–

EXT_LO1+ AUXADC_1

EXT_LO1– AUXADC_0

VSSA

ORX3+

VSSA

ORX3–

VSSA

TX3_EN

GPIO_11

GPIO_9

GPIO_3

GPIO_4

TX2_EN

VSSA

ORX1+

VSSA

ORX1–

VSSA

ORX_

CTRL_C

ORX_

CTRL_B

EXT_LO2+

AUXADC_2

VSSA

GPIO_12 GPIO_10

VRFVCO2_

1P3

VRFVCO2_

1P0

VRFVCO1_

1P0

VRFVCO1_

1P3

VDIG_1P0

VSSD

G

H

J

VSSA

ORX4+

VSSA

RX3_EN

GPIO_13

GPIO_5

GPIO_6

GPIO_7

GPIO_8

SPI_EN

RX2_EN

GPIO_0

RX1_EN

GPIO_1

VSSA

ORX2–

VSSA

RX1+

RX1–

VSSA

VCONV2_

1P8

VCONV1_

1P8

RX4–

VSSA

GPIO_17 GPIO_14

VSSA

VCONV2_

1P3

VRFSYN2_

1P3

VRFSYN1_

1P3

VCONV1_

1P3

VDIG_1P0

RX4+

RX4_EN

GPIO_15

VCONV2_

1P0

VCONV1_

1P0

K

L

VSSA

GPIO_18 GPIO_16

VSSD

VSSA

GPIO_

ANA_5

GPIO_

ANA_4

ORX_

CTRL_A

GPIO_

ANA_2

GPIO_

ANA_3

VDIG_1P0

VSSA

ORX4–

SPI_DIO

CTRL_D

ORX2+

VSSA

M

N

P

R

T

VSSA

TX4–

TX4+

VSSA

TX4_EN

GPINT2

SPI_DO

GPINT1

VSSD

VIF

SPI_CLK

RESET

TX1_EN

GPIO_2

VSSA

TX1+

TX1–

VCLKVCO_

1P3

VANA4_

1P8

VANA1_

1P8

SYNCOUT2+ SYNCOUT2–

SYNCIN3+

SYNCIN1+ SYNCIN1–

VCLKVCO_

1P0

VJVCO_

1P8

SYNCIN3– SYNCIN2+ SYNCIN2–

VCLKSYN_

VSSA

TEST_EN

VDES_1P0 VDES_1P0 VTT_DES SYNCOUT1+

VSSA

VJSYN_

1P0

VSER_

1P0

VSER_

1P0

SYNCOUT1–

VSSA

NIC

VSSA

1P3

SERDOUTC+ SERDOUTC–

SERDOUTA+ SERDOUTA–

SERDINA– SERDINA+

SERDINC– SERDINC+

VSSA

SERDOUTD+ SERDOUTD–

SERDOUTB+ SERDOUTB–

SERDINB+ SERDINB–

VSSA

SERDIND+ SERDIND–

U

VSSA

AUXILIARY

ANALOG GROUND

DIGITAL GROUND

ANALOG POWER

DIGITAL POWER

LVDS SERDES CONTROLS

SERDES INPUTS/OUTPUTS

DIFFERENTIAL SYSREF SIGNAL

NOT INTERNALLY CONNECTED

ADC INPUTS

ANALOG

INPUTS/OUTPUTS

DIGITAL

INPUTS/OUTPUTS

ANALOG GPIO

SPI BUS

NOTES

1. NIC = NOT INTERNALLY CONNECTED. THESE PINS MUST REMAIN DISCONNECTED.

Figure 2. Pin Configuration

Rev. 0 | Page 19 of 133

ADRV9029

Data Sheet

Table 13. Pin Function Descriptions

Pin No.

Mnemonic

Type¹Description

A1 to A3, A6, A8, A10 to A12, A15 to A17, B2, B3, B5 to

B10, B12, B13, B15, B16, C2, C7, C10, C14, C16, D1, D2, D4

to D7, D10 to D14, D16, D17, E3, E6, E12, E15, F3 to F6,

F12 to F15, G1, G2, G4, G6, G12, G14, G16, G17, H2, H4 to

H6, H12 to H14, H16, J2, J4, J6, J12, J14, J16, K1, K2, K4 to

K6, K12 to K14, K16, K17, L3, L6, L12, L15, M1 to M6, M12

to M17, N3, N4, P2 to P4, P9, P16, R1, R2, R5, R6, R8, R10,

R12 to R14, R16, R17, T1, T2, T5, T6, T9, T12, T13, T16, T17,

U3, U4, U7 to U11, U14, U15

VSSA

I

Analog Ground.

A4, A5

TX3+, TX3−

O

Differential Output for Transmitter Channel 3. If

unused, do not connect these pins.

A7

A9

A13, A14

VTXLO_1P3

VRXLO_1P3

TX2+, TX2−

I

O

1.3 V Supply Input.

Differential Output for Transmitter Channel 2.

When unused, do not connect.

B1, C1

RX3−, RX3+

I

Differential Input for Receiver Channel 3. If

unused, connect these pins to VSSA.

B4

VANA3_1P8

I

1.8 V Supply Input.

B11

VAUXVCO_1P0

O

1.0 V Internal Supply Node. Bypass Pin B11 with

a 4.7 μF capacitor.

B14

B17, C17

VANA2_1P8

RX2+, RX2−

I

1.8 V Supply Input.

Differential Input for Receiver Channel 2. If

unused, connect these pins to VSSA.

C3, R11

NIC

N/A

I/O

Not Internally Connected. These pins must

remain disconnected.

C4, C5, L1, L2, L17, L16, C12, C13

GPIO_ANA_7 to

GPIO_ANA_0

General-Purpose Inputs and Outputs. The

GPIO_ANA_7 to GPIO_ANA_0 pins are

referenced to 1.8 V and can also function as

auxiliary DAC outputs. If unused, these pins can

be connected to VSSA with a 10 kΩ resistor or

configured as outputs, driven low, and left

disconnected.

C6

VAUXSYN_1P3

DEVCLK+, DEVCLK−

VAUXVCO_1P3

RBIAS

I

1.3 V Supply Input.

Device Clock Differential Input.

1.3 V Supply Input.

Bias Resistor Connection. Pin C15 generates an

internal current based on an external 1%

resistor. Connect a 4.99 kΩ resistor between

Pin C15 and analog ground (VSSA).

C8, C9

C11

C15

D3

D8, D9

VANA2_1P3

SYSREF+, SYSREF−

I

1.3 V Supply Input.

LVDS System Reference Clock Inputs for the

SERDES Interface. Connect a 100 Ω termination

between these pins.

D15

E1

VANA1_1P3

AUXADC_3

I

1.3 V Supply Input.

Auxiliary ADC 3 Input. If Pin E1 is unused, do

not connect.

E2, F2

EXT_LO2−,

EXT_LO2+

I/O

Differential External LO Input/Output 2. If used

for the external LO input, the input frequency

must be 2× the desired carrier frequency. Do

not connect if unused. External LO functionality

not supported currently.

E4, E5

E7

ORX3+, ORX3−

TX3_EN

I

Differential Input for Observation Receiver

Channel 3. Connect to VSSA if unused.

Enable Input for Transmitter Channel 3.

Connect to VSSA if unused.

Rev. 0 | Page 20 of 133

Data Sheet

ADRV9029

Pin No.

Mnemonic

Type¹Description

H11, K11, N11, E10, F10, G10, H10, J10, K10, E9, F9, E8, F8, GPIO_0 to GPIO_18

G8, H8, J8, K8, H7, K7

I/O

General-Purpose Digital Inputs and Outputs.

See Figure 2 to match the ball location to the

GPIO_x signal name. If unused, these pins can

be connected to VSSA with a 10 kΩ resistor or

configured as outputs, driven low, and left

disconnected.

E11

TX2_EN

I

Enable Input for Transmitter Channel 2.

Connect to VSSA if unused.

E13, E14

E16, F16

ORX1+, ORX1−

I

Differential Input for Observation Receiver

Channel 1. Connect to VSSA if unused.

EXT_LO1+,

EXT_LO1−

I/O

Differential External LO Input/Output 1. If used

for the external LO input, the input frequency

must be 2× the desired carrier frequency. Do

not connect if unused. External LO functionality

not currently supported.

E17

AUXADC_1

AUXADC_2

I

Auxiliary ADC 1 Input. Do not connect if

unused.

Auxiliary ADC 2 Input. Do not connect if

unused.

Determine Active Observation Receiver Path.

Connect to VSSA directly or with a pull-down

resistor if unused.

F1

F7, F11, L7, L11

ORX_CTRL_C,

ORX_CTRL_B,

ORX_CTRL_D,

ORX_CTRL_A

F17

AUXADC_0

I

Auxiliary ADC 0 Input. Do not connect if

unused.

G3

G5

VRFVCO2_1P3

VRFVCO2_1P0

I

O

1.3 V Supply Input.

1.0 V Internal Supply Node. Bypass this pin with

a 4.7 μF capacitor.

G7

RX3_EN

I

Enable Input for Receiver Channel 3. Connect

to VSSA if unused.

G9, J9, L9

G11

VDIG_1P0

RX2_EN

I

1.0 V Digital Supply Input.

Enable Input for Receiver Channel 2. Connect

to VSSA if unused.

G13

VRFVCO1_1P0

O

1.0 V Internal Supply Node. Bypass this pin with

a 4.7 μF capacitor.

G15

H1, J1

VRFVCO1_1P3

RX4−, RX4+

I

1.3 V Supply Input.

Differential Input for Receiver Channel 4. If

unused, connect to VSSA.

H3

H9, K9, M9

H15

VCONV2_1P8

VSSD

VCONV1_1P8

RX1+, RX1−

I

1.8 V Supply Input.

Digital Ground.

1.8 V Supply Input.

Differential Input for Receiver Channel 1. If

unused, connect to VSSA.

H17, J17

J3

J5

J7

VCONV2_1P3

VRFSYN2_1P3

RX4_EN

I

1.3 V Supply Input.

Enable Input for Receiver Channel 4. If unused,

connect to VSSA.

J11

RX1_EN

I

Enable Input for Receiver Channel 1. If unused,

connect to VSSA.

J13

J15

K3

VRFSYN1_1P3

VCONV1_1P3

VCONV2_1P0

I

O

1.3 V Supply Input.

1.0 V Internal Supply Node. Bypass this pin with

a 4.7 μF capacitor.

K15

VCONV1_1P0

O

I

1.0 V Internal Supply Node. Bypass this pin with

a 4.7 μF capacitor.

Differential Input for Observation Receiver

Channel 4. If unused, connect to VSSA.

L4, L5

ORX4+, ORX4−

Rev. 0 | Page 21 of 133

ADRV9029

Data Sheet

Pin No.

Mnemonic

Type¹Description

L8

SPI_DIO

I/O

Serial Data Input. SPI_DIO is the serial data

input in 4-wire mode or input/output in 3-wire

mode.

L10

SPI_EN

I

Serial Data Bus Chip Select. Active low.

L13, L14

ORX2+, ORX2−

Differential Input for Observation Receiver

Channel 2. If unused, connect to VSSA.

M7

TX4_EN

I

Enable Input for Transmitter Channel 4.

If unused, connect to VSSA.

M8

M10

M11

SPI_DO

SPI_CLK

TX1_EN

O

I

Serial Data Output.

Serial Data Bus Clock Input.

Enable Input for Transmitter Channel 1.

If unused, connect to VSSA.

N1, P1

TX4−, TX4+

O

Differential Output for Transmitter Channel 4. If

unused, do not connect.

N2

N5

N6, P6

VANA4_1P8

VCLKVCO_1P3

SYNCIN3+,

SYNCIN3−

I

1.8 V Supply Input.

1.3 V Supply Input.

LVDS Sync Signal Input 3. If unused, connect to

VSSA.

N7

N8

GPINT2

O

General-Purpose Interrupt Output 2. If unused,

do not connect.

General-Purpose Interrupt Output 1. If unused,

do not connect.

GPINT1

N9

N10

VIF

RESET

I

1.8 V Interface Supply Input.

Active Low Chip Reset.

N12, N13

SYNCIN1+,

SYNCIN1−

LVDS Sync Signal Input 1. If unused, connect to

VSSA.

N14, N15

SYNCOUT2+,

SYNCOUT2−

O

LVDS Sync Signal Output 2. If unused, do not

connect.

N16

N17, P17

VANA1_1P8

TX1+, TX1−

I

O

1.8 V Supply Input.

Differential Output for Transmitter Channel 1.

Do not connect if unused.

P5

VCLKVCO_1P0

O

I

1.0 V Internal Supply Node. Bypass this pin with

a 4.7 μF capacitor.

LVDS Sync Signal Input 2. If unused, connect to

VSSA.

Test Input for JTAG Boundary Scan. Pull high to

enable boundary scan. If unused, tie to VSSA.

P7, P8

P10

SYNCIN2+,

SYNCIN2−

TEST_EN

I

P11

P12, P13

P14

VJVCO_1P8

VDES_1P0

VTT_DES

I

1.8 V Supply Input.

1.0 V Analog Supply Input.

P15, R15

SYNCOUT1+,

SYNCOUT1−

O

LVDS Sync Signal Output 1. If unused, do not

connect.

R3, R4

R7

R9

VSER_1P0

VCLKSYN_1P3

VJSYN_1P0

I

1.0 V Analog Supply Input.

1.3 V Supply Input.

1.0 V Analog Supply Input.

T3, T4

SERDOUTC+,

SERDOUTC−

O

SERDES Differential Output C. If unused, do not

connect.

T7, T8

SERDOUTA+,

SERDOUTA−

SERDINA−,

SERDINA+

SERDINC−,

SERDINC+

SERDOUTD+,

SERDOUTD-

O

I

SERDES Differential Output A. If unused, do not

connect.

SERDES Differential Input A. If unused, do not

connect.

SERDES Differential Input C. If unused, do not

connect.

SERDES Differential Output D. If unused, do not

connect.

T10, T11

T14, T15

U1, U2

U5, U6

I

O

SERDOUTB+,

SERDOUTB−

SERDES Differential Output B. If unused, do not

connect.

Rev. 0 | Page 22 of 133

Data Sheet

ADRV9029

Pin No.

Mnemonic

Type¹Description

U12, U13

SERDINB+,

SERDINB−

I

SERDES Differential Input B. If unused, do not

connect.

U16, U17

SERDIND+,

SERDIND−

I

SERDES Differential Input D. If unused, do not

connect.

¹I is input, O is output, I/O is input/output, and N/A is not applicable.

Rev. 0 | Page 23 of 133

ADRV9029

Data Sheet

TYPICAL PERFORMANCE CHARACTERISTICS

Device configuration profile: receiver = 62.5 MHz bandwidth, I/Q rate = 76.8 MHz, transmitter = 62.5 MHz large signal bandwidth plus

141 MHz synthesis bandwidth, I/Q rate = 153.6 MHz, observation receiver (OR_X) = 141 MHz bandwidth, I/Q rate = 153.6 MHz, device

clock = 153.6 MHz, unless otherwise noted.

75 MHZ BAND

The temperature settings refer to the die temperature. All LO frequencies set to 75 MHz, unless otherwise noted.

–100

–110

–120

–130

–140

–150

–160

–170

–180

10

9

8

7

6

5

4

3

2

1

0

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C

+25°C

+110°C

0

5

10

15

20

50

150

250

350

450

550

650

TRANSMITTER ATTENUATION (dB)

TRANSMITTER LO FREQUENCY (MHz)

Figure 6. Transmitter Noise vs. Transmitter Attenuation, 10 MHz Offset

Figure 3. Transmitter Continuous Wave Output Power vs. Transmitter LO

Frequency, 10 MHz Offset, 0 dB Attenuation

1.0

0

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

SIGNAL

0.8

0.6

NOISE FLOOR

–10

–20

–30

–40

–50

–60

–70

–80

–90

–100

0.4

0.2

0

–0.2

–0.4

–0.6

–0.8

–1.0

0

5

10 15 20 25 30 35 40 45 50 55 60 65 70

BASEBAND OFFSET FREQUENCY (MHz)

25

125 225 325 425 525 625 725 825 925 1025

FREQUENCY (MHz)

Figure 7. Transmitter Pass Band Flatness vs. Baseband Offset Frequency

Figure 4. Transmitter Output Power Spectrum, Tx1, 5 MHz LTE,

10 MHz Offset, −10 dBFS RMS, 1 MHz Resolution Bandwidth, T_J= 25°C

–40

–40°C

+25°C

+110°C

–50

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–45

–50

–60

–55

–60

–65

–70

–75

–80

–70

–80

–90

–100

0

5

10

15

20

–30

–20

–10

0

10

20

30

TRANSMITTER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 8. Adjacent Channel Power Level vs. Transmitter Attenuation, 21 MHz

Baseband Offset, 5 MHz LTE,

Figure 5. Transmitter Image Rejection Across Large Signal Bandwidth vs.

Baseband Offset Frequency

Peak to Average Ratio (PAR) = 12 dB

Rev. 0 | Page 24 of 133

Data Sheet

ADRV9029

–40

0.05

0.04

0.03

0.02

0.01

0

–40°C

+25°C

+110°C

–40°C

+25°C

+110°C

–45

–50

–55

–60

–65

–70

–75

–0.01

–0.02

–0.03

–0.04

–0.05

–80

0

5

10

15

20

0

4

8

12

16

20

24

28

32

TRANSMITTER ATTENUATION (dB)

Figure 9. Adjacent Channel Power Level vs. Transmitter Attenuation,

44 MHz Baseband Offset, 5 MHz LTE, PAR = 12 dB

Figure 12. Transmitter Attenuator Step Error vs. Transmitter Attenuation,

10 MHz Offset

–60

–45

–40°C, LOWER HD2

–40°C, UPPER HD2

+25°C, LOWER HD2

+25°C, UPPER HD2

+110°C, LOWER HD2

+110°C, UPPER HD2

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–46

–47

–48

–49

–50

–51

–52

–53

–70

–80

–90

–100

–110

–120

0

2

4

6

8

10

12

14

16

18

20

0

2

4

6

8

10

12

14

16

18

20

TRANSMITTER ATTENUATOR SETTING (dB)

Figure 10. Transmitter Second-Order Harmonic Distortion (HD2) vs.

Transmitter Attenuation, 10 MHz Offset

Figure 13. Transmitter Error Vector Magnitude vs. Transmitter Attenuation, 5

MHz LTE Signal Centered at LO Frequency, Sample Rate = 153.6 MSPS, Loop

Filter Bandwidth = 50 kHz, Loop Filter Phase Margin = 40°

45

–60

–40°C, LOWER HD3

–40°C, UPPER HD3

+25°C, LOWER HD3

+25°C, UPPER HD3

+110°C, LOWER HD3

+110°C, UPPER HD3

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

40

35

30

25

20

15

10

5

–70

–80

–90

–100

–110

–120

0

–5

–10

0

2

4

6

8

10

12

14

16

18

20

0

4

8

12

16

20

24

28

32

TRANSMITTER ATTENUATOR SETTING (dB)

TRANSMITTER ATTENUATION (dB)

Figure 11. Transmitter Third-Order Harmonic Distortion (HD3) vs.

Transmitter Attenuation, 10 MHz Offset

Figure 14. Transmitter OIP3, 2f1 − f2 vs. Transmitter Attenuation, 15 dB

Digital Back Off per Tone, f1 = 45.5 MHz, f2 = 50.5 MHz

Rev. 0 | Page 25 of 133

ADRV9029

Data Sheet

45

40

35

30

25

20

15

10

5

100

95

90

85

80

75

70

65

60

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

0

–5

–10

0

4

8

12

16

20

24

28

32

50

60

70

80

90

100

TRANSMITTER ATTENUATION (dB)

TRANSMITTER LO FREQUENCY (MHz)

Figure 15. Transmitter OIP3, 2f2 − f1 vs. Transmitter Attenuation, 15 dB

Figure 18. Transmitter LO Leakage vs. Transmitter LO Frequency

Digital Back Off per Tone, f1 = 45.5 MHz, f2 = 50.5 MHz

50

120

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

Tx1 TO Tx2

Tx2 TO Tx1

Tx3 TO Tx1

Tx4 TO Tx1

Tx1 TO Tx3

Tx2 TO Tx3

Tx3 TO Tx2

Tx4 TO Tx2

Tx1 TO Tx4

Tx2 TO Tx4

Tx3 TO Tx4

Tx4 TO Tx3

45

40

35

30

25

20

15

10

5

110

100

90

80

70

60

0

50

75

175

275

375

475

575

675

15

25

35

45

55

65

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

TRANSMITTER LO FREQUENCY (MHz)

Figure 16. Transmitter OIP3, 2f1 − f2 vs. f1 Baseband Offset Tone Frequency,

Figure 19. Transmitter to Transmitter Isolation vs. Transmitter LO Frequency

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

50

130

120

110

100

90

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

45

40

35

30

25

20

15

10

5

80

70

Tx1 TO Rx1

Tx2 TO Rx1

Tx3 TO Rx1

Tx4 TO Rx1

Tx1 TO Rx2

Tx2 TO Rx2

Tx3 TO Rx2

Tx4 TO Rx2

Tx1 TO Rx3

Tx2 TO Rx3

Tx3 TO Rx3

Tx4 TO Rx3

Tx1 TO Rx4

Tx2 TO Rx4

Tx3 TO Rx4

Tx4 TO Rx4

60

0

50

15

25

35

45

55

65

75

175

275

375

475

575

675

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 17. Transmitter OIP3, 2f2 − f1 vs. f1 Baseband Oﬀset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

Figure 20. Transmitter to Receiver Isolation vs. Receiver LO Frequency

Rev. 0 | Page 26 of 133

Data Sheet

ADRV9029

130

120

110

100

90

25

20

15

10

5

–40°C

+25°C

+110°C

80

70

Tx1 TO ORx1

Tx1 TO ORx2

Tx2 TO ORx2

Tx3 TO ORx2

Tx4 TO ORx2

Tx1 TO ORx3

Tx2 TO ORx3

Tx3 TO ORx3

Tx4 TO ORx3

Tx1 TO ORx4

Tx2 TO ORx4

Tx3 TO ORx4

Tx4 TO ORx4

Tx2 TO ORx1

Tx3 TO ORx1

Tx4 TO ORx1

60

50

0

–25 –20 –15 –20

–5

0

5

10

15

20

25

75

175

275

375

475

575

675

TRANSMITTER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 21. Transmitter to Observation Receiver Isolation vs. Transmitter

Figure 24. Receiver Integrated Noise Figure vs. Baseband Offset Frequency,

62.5 MHz Bandwidth, Sample Rate = 76.8 MSPS, Integrated in 200 kHz Steps

LO Frequency

120

–40

–40°C

+25°C

+110°C

110

100

90

–50

–60

–70

80

–80

70

Rx1 TO Rx2

Rx2 TO Rx1

Rx3 TO Rx1

Rx4 TO Rx1

Rx1 TO Rx3

Rx2 TO Rx3

Rx3 TO Rx2

Rx4 TO Rx2

Rx1 TO Rx4

Rx2 TO Rx4

Rx3 TO Rx4

Rx4 TO Rx3

–90

60

50

–100

75

175

275

375

475

575

675

75

125

175

225

275

325

375

425

475

525

RECEIVER LO FREQUENCY (MHz)

Figure 22. Receiver to Receiver Isolation vs. Receiver LO Frequency

Figure 25. Receiver LO Leakage vs. Receiver LO Frequency,

Attenuation = 0 dB, Sample Rate = 76.8 MSPS

20

15

10

5

50

45

40

35

30

25

20

15

0

–5

–10

–15

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

10

5

0

5

10

15

20

25

0

5

10

15

20

RECEIVER ATTENUATION (dB)

Figure 26. Receiver Gain vs. Receiver Attenuation, 20 MHz Offset, 62.5 MHz

Bandwidth, Sample Rate = 76.8 MSPS

Figure 23. Receiver Integrated Noise Figure vs. Receiver Attenuation,

62.5 MHz Bandwidth, Sample Rate =76.8 MSPS,

Integration Bandwidth = 500 kHz to 30 MHz

Rev. 0 | Page 27 of 133

ADRV9029

Data Sheet

0.20

0.15

0.10

0.05

0

–40

–50

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–60

–70

–80

–0.05

–0.10

–0.15

–90

–100

–110

–0.20

0

5

10

15

20

25

30

0

5

10

15

20

25

RECEIVER ATTENUATION (dB)

Figure 27. Receiver Gain Step Error vs. Receiver Attenuation,

10 MHz Offset, −5 dBFS Input Signal

Figure 30. Receiver DC Offset vs. Receiver Attenuation, 10 MHz Offset,

−5 dBFS Input Signal

–40

–50

–60

–70

–80

–90

–100

–40

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C

+25°C

+110°C

–45

–50

–55

–60

–65

–70

–75

–30

–20

–10

0

10

20

30

75

125

175

225

275

325

375

425

475

525

BASEBAND OFFSET FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 28. Receiver Image vs. Baseband Offset Frequency,

Tracking Calibration Active, Sample Rate = 76.8 MSPS

Figure 31. Receiver DC Offset vs. Receiver LO Frequency, 10 MHz Offset,

−5 dBFS Input Signal

–40

–50

–60

–70

–80

–90

–100

–40

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–50

–60

–70

–80

–90

–100

–110

–120

0

5

10

15

20

25

–18

–12

–6

0

6

12

18

RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 29. Receiver Image vs. Receiver Attenuation, 10 MHz Offset, Tracking

Calibration Active, Sample Rate = 76.8 MSPS

Figure 32. Receiver HD2, Left Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

(HD2 Canceller Enabled)

Rev. 0 | Page 28 of 133

Data Sheet

ADRV9029

–40

90

85

80

75

70

65

60

55

50

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–50

–60

–70

–80

–90

–100

–110

–120

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–18

–12

–6

0

6

12

18

79

83

87

91

BASEBAND OFFSET FREQUENCY (MHz)

TONE 2 FREQUENCY (MHz)

Figure 33. Receiver HD2, Right Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz (HD2 Canceller

Enabled)

Figure 36. Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

90

85

80

75

70

65

60

55

50

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–50

–60

–70

–80

–90

–100

–110

–120

79

83

87

91

95

99

103

–12

–9

–6

–3

0

3

6

9

12

TONE 2 FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 37. Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Figure 34. Receiver HD3, Left Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

90

85

80

75

70

65

60

55

50

–40

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1 +110°C, Rx1

+25°C, Rx2 +110°C, Rx2

+25°C, Rx3 +110°C, Rx3

+25°C, Rx4 +110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–50

–60

–70

–80

–90

–100

–110

–120

4

8

12

16

20

24

28

–12

–9

–6

–3

0

3

6

9

12

TWO-TONE FREQUENCY SPACING (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 38. Receiver IIP2, f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Figure 35. Receiver HD3, Right Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

Rev. 0 | Page 29 of 133

ADRV9029

Data Sheet

90

85

80

75

70

65

60

55

35

30

25

20

15

10

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

50

4

8

12

16

20

24

28

4

5

6

7

8

9

10

11

12

TWO-TONE FREQUENCY SPACING (MHz)

Figure 39. Receiver IIP2, f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Figure 42. Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

40

35

30

25

20

15

10

35

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

–40°C, Rx4

+25°C, Rx4

+110°C, Rx4

30

25

20

15

10

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

5

0

79

83

87

91

95

99

103

4

8

12

16

20

24

28

TONE 2 FREQUNCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 40. Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Figure 43. Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

40

35

30

25

20

15

10

5

35

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

30

25

20

15

10

0

79

83

87

91

95

99

103

4

6

8

10

12

TWO-TONE FREQUENCY SPACING (MHz)

TONE 2 FREQUNCY (MHz)

Figure 44. Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Figure 41. Receiver IIP3, 2f2 – f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Rev. 0 | Page 30 of 133

Data Sheet

ADRV9029

35

30

25

20

15

10

5

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

30

25

20

15

10

0

4

8

12

16

20

24

28

–50 –40 –30 –20 –10

0

10

20

30

40

50

TWO-TONE FREQUENCY SPACING (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 45. Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Figure 48. Observation Receiver Integrated Noise Figure vs. Baseband Offset

Frequency, 141 MHz Bandwidth, Sample Rate =153.6 MSPS,

Integrated in 200 kHz Steps

–40

–20

–40°C

+25°C

+110°C

–50

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–23

–26

–29

–32

–35

–38

–41

–44

–47

–50

–60

–70

–80

–90

–100

75

125

175

225

275

325

375

425

475

525

–60

–55

–50

–45

–40

–35

–30

–25

–20

OBSERVATION RECEIVER LO FREQUENCY (MHz)

RECEIVER INPUT POWER (dBm)

Figure 46. Receiver Error Vector Magnitude vs. Receiver Input Power,

20 MHz LTE Signal Centered at LO Frequency, Sample Rate = 153.6 MSPS,

Loop Filter Bandwidth = 50 kHz, Loop Filter Phase Margin = 40°

Figure 49. Observation Receiver LO Leakage vs. Observation Receiver

LO Frequency, Attenuation = 0 dB, Sample Rate = 153.6 MSPS

50

20

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

45

40

35

30

25

20

15

10

5

15

10

5

0

–5

–10

–15

0

5

10

15

20

0

5

10

15

20

25

30

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 47. Observation Receiver (ORx) Integrated Noise Figure vs.

Observation Receiver Attenuation, 141 MHz Bandwidth, Sample Rate = 153.6

MSPS, Integration Bandwidth = 500 kHz to 70.5 MHz

Figure 50. Observation Receiver Gain vs. Observation Receiver Attenuation,

14.1 MHz Offset, 141 MHz Bandwidth, Sample Rate = 153.6 MSPS

Rev. 0 | Page 31 of 133

ADRV9029

Data Sheet

–40

–50

–60

–70

–80

–90

–100

0.20

0.15

0.10

0.05

0

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–0.05

–0.10

–0.15

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–0.20

0

5

10

15

20

25

30

5

10

15

20

25

30

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 51. Observation Receiver Gain Step Error vs. Observation Receiver

Attenuation, 14.1 MHz Offset, −10 dBFS Input Signal

Figure 54. Observation Receiver Image vs. Observation Receiver Attenuation,

14.1 MHz Offset, Tracking Calibration Active, Sample Rate =153.6 MSPS

1.0

–40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C

+25°C

0.8

0.6

+110°C

–50

–60

–70

–80

–90

0.4

0.2

0

–0.2

–0.4

–0.6

–0.8

–1.0

0

5

10 15 20 25 30 35 40 45 50 55 60

BASEBAND OFFSET FREQUENCY (MHz)

0

5

10

15

20

25

30

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 52. Normalized Observation Receiver Flatness vs. Baseband Offset

Frequency, −10 dBFS Input Signal

Figure 55. Observation Receiver DC Offset vs. Observation Receiver

Attenuation, 14.1 MHz Offset, −10 dBFS Input Signal

–40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–50

–60

–50

–60

–70

–80

–90

–80

–100

–110

–120

–90

–100

–70 –60 –50 –40 –30 –20 –10

0

10 20 30 40 50 60 70

–35 –30 –25 –20 –15 –10 –5

0

5

10 15 20 25 30 35

BASEBAND OFFSET FREQUENCY (MHz)

Figure 53. Observation Receiver Image vs. Baseband Offset Frequency,

Tracking Calibration Active, Sample Rate =153.6 MSPS

Figure 56. Observation Receiver HD2, Left Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

Rev. 0 | Page 32 of 133

Data Sheet

ADRV9029

90

85

80

75

70

65

60

55

50

45

40

–40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–50

–60

–70

–80

–90

–100

–110

–120

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–35 –30 –25 –20 –15 –10 –5

0

5

10 15 20 25 30 35

79

83

87

91

95

99

103

107

111

TONE 2 FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 57. Observation Receiver HD2, Right Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

Figure 60. Observation Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

–40

90

85

80

75

70

65

60

55

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–50

–60

–70

–80

–90

–100

–110

–120

50

45

40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–20

–15

–10

–5

0

5

10

15

20

79 83 87 91 95 99 103 107 111 115 119 123 127 131

TONE 2 FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 58. Observation Receiver HD3, Left Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

Figure 61. Observation Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

90

80

70

60

–40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–50

–60

–70

–80

–90

–100

–110

–120

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

50

40

4

8

12 16 20 24 28 32 36 40 44 48 52 56

TWO-TONE FREQUENCY SPACING (MHz)

–20

–15

–10

–5

0

5

10

15

20

BASEBAND OFFSET FREQUENCY (MHz)

Figure 59. Observation Receiver HD3, Right Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

Figure 62. Observation Receiver IIP2, f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −13 dBFS, f2 = 2 MHz

Rev. 0 | Page 33 of 133

ADRV9029

Data Sheet

90

80

70

60

40

36

32

28

24

20

16

12

8

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

50

40

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

4

0

4

8

12 16 20 24 28 32 36 40 44 48 52 56

TWO-TONE FREQUENCY SPACING (MHz)

79

83

87

91

95

TONE 2 FREQUENCY (MHz)

Figure 63. Observation Receiver IIP2, f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −13 dBFS, f2 = 2 MHz

Figure 66. Observation Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

120

110

100

90

40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

36

32

28

24

20

16

12

8

80

70

60

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

50

40

4

0

5

10

15

20

25

30

79

83

87

91

95

OBSERVATION RECEIVER ATTENUATION (dB)

TONE 2 FREQUENCY

Figure 64. Observation Receiver IIP2, f1 + f2 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 45 MHz, f2 = 2 MHz

Figure 67. Observation Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

120

110

100

90

40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

36

32

28

24

20

16

12

8

80

70

60

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

50

40

4

0

5

10

15

20

25

30

79 83 87 91 95 99 103 107 111 115 119 123 127 131

TONE 2 FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 65. Observation Receiver IIP2, f1 − f2 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 45 MHz, f2 = 2 MHz

Figure 68. Observation Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Rev. 0 | Page 34 of 133

Data Sheet

ADRV9029

40

30

25

20

15

10

5

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

36

32

28

24

20

16

12

8

4

0

79 83 87 91 95 99 103 107 111 115 119 123 127 131

TONE 2 FREQUENCY (MHz)

4

8

12

16

20

TWO-TONE FREQUENCY SPACING (MHz)

Figure 69. Observation Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 71. Observation Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency Spacing,

Both Tones at −13 dBFS, f2 = 2 MHz

30

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

25

20

15

10

5

25

20

15

10

5

0

4

8

12

16

20

4

8

12

16

20

24

28

32

TWO-TONE FREQUENCY SPACING (MHz)

Figure 70. Observation Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

Figure 72. Observation Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −13 dBFS, f2 = 2 MHz

Rev. 0 | Page 35 of 133

ADRV9029

Data Sheet

30

40

35

30

25

20

15

10

5

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

25

20

15

10

5

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

0

5

10

15

20

4

8

12

16

20

24

28

32

OBSERVATION RECEIVER ATTENUATION (dB)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 75. Observation Receiver IIP3, 2f2 − f1 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 45 MHz, f2 = 2 MHz

Figure 73. Observation Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency Spacing,

Both Tones at −13 dBFS, f2 = 2 MHz

40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

35

30

25

20

15

10

5

0

5

10

15

20

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 74. Observation Receiver IIP3, 2f2 + f1 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 45 MHz, f2 = 2 MHz

Rev. 0 | Page 36 of 133

Data Sheet

ADRV9029

800 MHz BAND

The temperature settings refer to the die temperature. All LO frequencies set to 800 MHz, unless otherwise noted.

10

9

8

7

6

5

4

3

2

1

0

–100

–110

–120

–130

–140

–150

–160

–170

–180

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+110°C

+25°C

–40°C

800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800

0

5

10

15

20

TRANSMITTER LO FREQUENCY (MHz)

TRANSMITTER ATTENUATION (dB)

Figure 76. Transmitter Continuous Wave Output Power vs. Transmitter LO

Frequency, 10 MHz Offset, 0 dB Attenuation

Figure 79. Transmitter Noise vs. Transmitter Attenuation, 10 MHz Offset

1.0

0

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

SIGNAL

NOISE FLOOR

–10

–20

0.8

0.6

0.4

0.2

0

–30

–40

–50

–60

–70

–80

–90

–100

–0.2

–0.4

–225 –175 –125 –75

–25

25

75

125

175

225

BASEBAND OFFSET FREQUENCY (MHz)

FREQUENCY (MHz)

Figure 77. Transmitter Output Power Spectrum, Tx1, 5 MHz LTE,

10 MHz Offset, −10 dBFS RMS, 1 MHz Resolution Bandwidth, T_J= 25°C

Figure 80. Transmitter Pass Band Flatness vs. Baseband Offset Frequency

–40

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+110°C

+25°C

–40°C

–45

–50

–55

–60

–65

–70

–75

–80

–50

–60

–70

–80

–90

–100

–100 –80 –60 –40 –20

0

20

40

60

80

100

0

5

10

15

20

BASEBAND OFFSET FREQUENCY (MHz)

TRANSMITTER ATTENUATION (dB)

Figure 78. Transmitter Image Rejection Across Large Signal Bandwidth vs.

Baseband Offset Frequency

Figure 81. Adjacent Channel Power Level vs. Transmitter Attenuation,

−10 MHz Baseband Offset, 20 MHz LTE,

Peak to Average Ratio (PAR) = 12 dB

Rev. 0 | Page 37 of 133

ADRV9029

Data Sheet

–40

–45

–50

–55

–60

–65

–70

–75

0.05

0.04

0.03

0.02

0.01

0

+110°C

+25°C

–40°C

+110°C

+25°C

–40°C

–0.01

–0.02

–0.03

–0.04

–0.05

–80

0

5

10

15

20

0

4

8

12

16

20

24

28

32

TRANSMITTER ATTENUATION (dB)

Figure 82. Adjacent Channel Power Level vs. Transmitter Attenuation,

90 MHz Baseband Offset, 20 MHz LTE, PAR = 12 dB

Figure 85. Transmitter Attenuator Step Error vs. Transmitter Attenuation,

10 MHz Offset

–60

–42

+110°C, LOWER HD2

+25°C, LOWER HD2

–40°C, LOWER HD2

+110°C, UPPER HD2

+25°C, UPPER HD2

–40°C, UPPER HD2

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–70

–80

–44

–46

–48

–50

–52

–90

–100

–110

–120

0

2

4

6

8

10

12

14

16

18

20

0

5

10

15

20

TRANSMITTER ATTENUATION (dB)

Figure 83. Transmitter Second-Order Harmonic Distortion (HD2) vs.

Transmitter Attenuation, 10 MHz Offset

Figure 86. Transmitter Error Vector Magnitude vs. Transmitter Attenuation,

20 MHz LTE Signal Centered at LO Frequency, Sample Rate = 491.52 MSPS, Loop

Filter Bandwidth = 50 kHz, Loop Filter Phase Margin = 85°

–60

45

40

35

30

25

20

15

10

5

+110°C, LOWER HD3

+25°C, LOWER HD3

–40°C, LOWER HD3

+110°C, UPPER HD3

+25°C, UPPER HD3

–40°C, UPPER HD3

–70

–80

–90

–100

–110

–120

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

0

–5

0

2

4

6

8

10

12

14

16

18

20

–10

0

4

8

12

16

20

24

28

32

TRANSMITTER ATTENUATION (dB)

Figure 84. Transmitter Third-Order Harmonic Distortion (HD3) vs.

Transmitter Attenuation, 10 MHz Offset

Figure 87. Transmitter OIP3, 2f1 − f2 vs. Transmitter Attenuation, 15 dB

Digital Back Off per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

Rev. 0 | Page 38 of 133

Data Sheet

ADRV9029

45

40

35

30

25

20

15

10

5

50

45

40

35

30

25

20

15

10

5

–40°C, Tx1

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

0

–5

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

–10

0

10

0

4

8

12

16

20

24

28

32

30

50

70

90

110

130

150

170

190

TRANSMITTER ATTENUATION (dB)

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 91. Transmitter OIP3, 2f1 + f2 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

Figure 88. Transmitter OIP3, 2f2 − f1 vs. Transmitter Attenuation, 15 dB

Digital Back Off per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

50

45

40

35

30

25

20

15

50

45

40

35

30

25

20

15

10

5

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

10

5

0

10

0

10

30

50

70

90

110

130

150

170

190

30

50

70

90

110

130

150

170

190

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 89. Transmitter OIP3, 2f1 − f2 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

Figure 92. Transmitter OIP3, 2f2 + f1 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

50

45

40

35

30

25

20

15

100

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

95

90

85

80

75

70

65

60

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

10

5

0

10

30

50

70

90

110

130

150

170

190

800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

TRANSMITTER LO FREQUENCY(MHz)

Figure 90. Transmitter OIP3, 2f2 − f1 vs. f1 Baseband Oﬀset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

Figure 93. Transmitter LO Leakage vs. Transmitter LO Frequency

Rev. 0 | Page 39 of 133

ADRV9029

Data Sheet

120

110

100

90

120

110

100

90

Tx1 TO Tx2

Tx2 TO Tx1

Tx3 TO Tx1

Tx4 TO Tx1

Tx1 TO Tx3

Tx2 TO Tx3

Tx3 TO Tx2

Tx4 TO Tx2

Tx1 TO Tx4

Tx2 TO Tx4

Tx3 TO Tx4

Tx4 TO Tx3

80

70

Rx1 TO Rx2

Rx2 TO Rx1

Rx3 TO Rx1

Rx4 TO Rx1

Rx1 TO Rx3

Rx2 TO Rx3

Rx3 TO Rx2

Rx4 TO Rx2

Rx1 TO Rx4

Rx2 TO Rx4

Rx3 TO Rx4

Rx4 TO Rx3

60

50

700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800

RECEIVER LO FREQUENCY (MHz)

TRANSMITTER LO FREQUENCY (MHz)

Figure 97. Receiver to Receiver Isolation vs. Receiver LO Frequency

Figure 94. Transmitter to Transmitter Isolation vs. Transmitter LO Frequency

50

130

120

110

100

90

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

45

40

35

30

25

20

15

10

0

80

70

Tx1 TO Rx1

Tx2 TO Rx1

Tx3 TO Rx1

Tx4 TO Rx1

Tx1 TO Rx2

Tx2 TO Rx2

Tx3 TO Rx2

Tx4 TO Rx2

Tx1 TO Rx3

Tx2 TO Rx3

Tx3 TO Rx3

Tx4 TO Rx3

Tx1 TO Rx4

Tx2 TO Rx4

Tx3 TO Rx4

Tx4 TO Rx4

60

50

0

5

10

15

20

700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800

RECEIVER ATTENUATION (dB)

RECEIVER LO FREQUENCY (MHz)

Figure 98. Receiver Integrated Noise Figure vs. Receiver Attenuation,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS,

Integration Bandwidth = 500 kHz to 100 MHz

Figure 95. Transmitter to Receiver Isolation vs. Receiver LO Frequency

130

120

110

100

90

20

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

18

16

14

12

10

8

80

Tx1 TO ORx1

Tx2 TO ORx1

Tx3 TO ORx1

Tx4 TO ORx1

Tx1 TO ORx3

Tx2 TO ORx3

Tx3 TO ORx3

Tx4 TO ORx3

Tx1 TO ORx2

Tx2 TO ORx2

Tx3 TO ORx2

Tx4 TO ORx2

Tx1 TO ORx4

Tx2 TO ORx4

Tx3 TO ORx4

Tx4 TO ORx4

70

60

50

6

700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800

800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800

TRANSMITTER LO FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 96. Transmitter to Observation Receiver Isolation vs. Transmitter

LO Frequency

Figure 99. Receiver Integrated Noise Figure vs. Receiver LO Frequency, 200 MHz

Bandwidth, Sample Rate = 245.76 MSPS,

Integration Bandwidth = 500 kHz to 100 MHz

Rev. 0 | Page 40 of 133

Data Sheet

ADRV9029

25

20

15

10

5

20

19

18

17

16

15

+110°C

+25°C

–40°C

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0

–100 –80 –60 –40 –20

0

20

40

60

80

100

800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800

BASEBAND OFFSET FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 100. Receiver Integrated Noise Figure vs. Baseband Offset Frequency,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS, Integrated in 200 kHz Steps

Figure 103. Receiver Gain vs. Receiver LO Frequency, 200 MHz Bandwidth,

Sample Rate = 245.76 MSPS

–40

0.20

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+110°C

+25°C

–40°C

0.15

0.10

0.05

0

–50

–60

–70

–80

–90

–0.05

–0.10

–0.15

–0.20

–100

800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800

0

5

10

15

20

25

30

RECEIVER LO FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 101. Receiver LO Leakage vs. Receiver LO Frequency,

Attenuation = 0 dB, Sample Rate = 245.76 MSPS

Figure 104. Receiver Gain Step Error vs. Receiver Attenuation,

20 MHz Offset, −5 dBFS Input Signal

20

15

10

5

0.5

+110°C

+25°C

–40°C

0.4

0.3

0.2

0.1

0

–0.1

–0.2

–0.3

–0.4

–0.5

–5

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–10

–15

0

5

10

15

20

25

–100 –80 –60 –40 –20

0

20

40

60

80

100

RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 102. Receiver Gain vs. Receiver Attenuation, 20 MHz Offset, 200 MHz

Bandwidth, Sample Rate = 245.76 MSPS

Figure 105. Normalized Receiver Flatness vs. Baseband Offset Frequency,

−5 dBFS Input Signal

Rev. 0 | Page 41 of 133

ADRV9029

Data Sheet

–40

–50

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–50

–60

–70

–80

–90

–100

–110

–100 –80 –60 –40 –20

0

20

40

60

80

100

800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800

RECEIVER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 106. Receiver Image vs. Baseband Offset Frequency,

Tracking Calibration Active, Sample Rate = 245.76 MSPS

Figure 109. Receiver DC Offset vs. Receiver LO Frequency, 20 MHz Offset,

−5 dBFS Input Signal

–40

–50

–60

–70

–80

–90

–100

–40

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–50

–60

–70

–80

–90

–100

–110

–120

0

5

10

15

20

25

–60

–40

–20

0

20

40

60

RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 107. Receiver Image vs. Receiver Attenuation, 20 MHz Offset, Tracking

Calibration Active, Sample Rate = 245.76 MSPS

Figure 110. Receiver HD2, Left Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

(HD2 Canceller Enabled)

–40

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–50

–60

–50

–60

–70

–80

–90

–100

–110

–100

–110

–120

–

0

5

10

15

20

25

–60

–40

–20

0

20

40

60

RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 108. Receiver DC Offset vs. Receiver Attenuation, 20 MHz Offset,

−5 dBFS Input Signal

Figure 111. Receiver HD2, Right Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz (HD2 Canceller

Enabled)

Rev. 0 | Page 42 of 133

Data Sheet

ADRV9029

–40

90

85

80

75

70

65

60

55

50

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–50

–60

–70

–80

–90

–100

–110

–120

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40

–30

–20

–10

0

10

20

30

40

805

815

825

835

845

855

865

875

885

895

BASEBAND OFFSET FREQUENCY (MHz)

TONE 2 FREQUENCY (MHz)

Figure 112. Receiver HD3, Left Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

Figure 115. Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

–40

90

85

80

75

70

65

60

55

50

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–50

–60

–70

–80

–90

–100

–110

–120

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40

–30

–20

–10

0

10

20

30

40

10

20

30

40

50

60

70

80

90

BASEBAND OFFSET FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 113. Receiver HD3, Right Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

Figure 116. Receiver IIP2, f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

90

85

80

75

70

65

60

90

85

80

75

70

65

60

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

55

50

55

50

805

815

825

TONE 2 FREQUENCY (MHz)

835

845

10

20

30

40

50

60

70

80

90

TWO-TONE FREQUENCY SPACING (MHz)

Figure 114. Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Figure 117. Receiver IIP2, f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Rev. 0 | Page 43 of 133

ADRV9029

Data Sheet

100

40

35

30

25

20

15

10

5

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

95

90

85

80

75

70

65

60

0

5

10

15

20

805

810

815

TONE 2 FREQUENCY (MHz)

820

825

RECEIVER ATTENUATION (dB)

Figure 118. Receiver IIP2, f1 + f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

Figure 121. Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

100

95

90

85

80

75

70

65

60

40

35

30

25

20

15

10

5

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0

805

0

5

10

15

20

815

825

835

845

855

865

875

885

RECEIVER ATTENUATION (dB)

TONE 2 FREQUENCY (MHz)

Figure 119. Receiver IIP2, f1 − f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

Figure 122. Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

40

35

30

25

20

15

10

5

40

35

30

25

20

15

10

5

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0

805

0

805

810

815

TONE 2 FREQUENCY (MHz)

820

825

815

825

835

845

855

865

875

885

895

TONE 2 FREQUENCY (MHz)

Figure 120. Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Figure 123. Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Rev. 0 | Page 44 of 133

Data Sheet

ADRV9029

35

30

25

20

15

10

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

30

25

20

15

10

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

10

15

20

25

30

35

40

10

20

30

40

50

60

70

80

90

TWO-TONE FREQUENCY SPACING (MHz)

Figure 124. Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Figure 127. Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

35

–20

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–23

–26

–29

–32

–35

–38

–41

–44

–47

–50

30

25

20

15

10

20

30

40

50

60

70

80

90

–60 –55 –50 –45 –40 –35 –30 –25 –20 –15 –10 –5

0

TWO-TONE FREQUENCY SPACING (MHz)

RECEIVER INPUT POWER (dBm)

Figure 125. Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Figure 128. Receiver Error Vector Magnitude vs. Receiver Input Power,

20 MHz LTE Signal Centered at LO Frequency, Sample Rate = 245.76 MSPS,

Loop Filter Bandwidth = 50 kHz, Loop Filter Phase Margin = 85°

35

–80

–90

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

30

25

20

15

10

–100

–110

–120

–130

–140

–150

–160

–170

10

15

20

25

30

35

40

100

1k

10k

100k

1M

10M

TWO-TONE FREQUENCY SPACING (MHz)

FREQUENCY OFFSET (Hz)

Figure 126. Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Figure 129. LO Phase Noise vs. Frequency Offset, Loop Bandwidth = 50 kHz,

Phase Margin = 85°

Rev. 0 | Page 45 of 133

ADRV9029

Data Sheet

40

35

30

25

20

15

10

5

–80

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–90

–100

–110

–120

–130

–140

–150

–160

–170

100

1k

10k

100k

1M

10M

–250

–150

–50

50

150

250

FREQUENCY OFFSET (Hz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 130. LO Phase Noise vs. Frequency Offset, Loop Bandwidth = 100 kHz,

Phase Margin = 60°

Figure 133. Observation Receiver Integrated Noise Figure vs. Baseband Offset

Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS,

Integrated in 200 kHz Steps

50

–40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+110°C

+25°C

–40°C

45

40

35

30

25

20

15

10

5

–50

–60

–70

–80

–90

0

–100

0

5

10

15

20

800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800

OBSERVATION RECEIVER ATTENUATION (dB)

OBSERVATION RECEIVER LO FREQUENCY (MHz)

Figure 131. Observation Receiver (ORx) Integrated Noise Figure vs.

Observation Receiver Attenuation, 450 MHz Bandwidth, Sample Rate =

491.52 MSPS, Integration Bandwidth = 500 kHz to 245.76 MHz

Figure 134. Observation Receiver LO Leakage vs. Observation Receiver

LO Frequency, Attenuation = 0 dB, Sample Rate = 491.52 MSPS

24

20

15

10

5

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

22

20

18

16

14

12

10

0

–5

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–10

–15

800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800

0

5

10

15

20

25

30

OBSERVATION RECEIVER LO FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 132. Observation Receiver Integrated Noise Figure vs. Observation

Receiver LO Frequency, Attenuation = 0 dB, Sample Rate = 491.52 MSPS,

Integration Bandwidth = 500 kHz to 245.76 MHz

Figure 135. Observation Receiver Gain vs. Observation Receiver Attenuation,

45 MHz Offset, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Rev. 0 | Page 46 of 133

Data Sheet

ADRV9029

20

19

18

17

–40

–50

–60

–70

–80

–90

–100

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

16

15

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800

–225 –175 –125 –75

–25

25

75

125

175

225

OBSERVATION RECEIVER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 136. Observation Receiver Gain vs. Observation Receiver LO

Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Figure 139. Observation Receiver Image vs. Baseband Offset Frequency,

Tracking Calibration Active, Sample Rate = 491.52 MSPS

–40

0.20

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

0.15

0.10

–50

–60

0.05

–70

0.00

–0.05

–0.10

–0.15

–0.20

–80

–90

–100

0

5

10

15

20

25

30

0

5

10

15

20

25

30

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 140. Observation Receiver Image vs. Observation Receiver Attenuation,

45 MHz Offset, Tracking Calibration Active, Sample Rate = 491.52 MSPS

Figure 137. Observation Receiver Gain Step Error vs. Observation Receiver

Attenuation, 45 MHz Offset, −10 dBFS Input Signal

–40

0.7

0.5

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–50

–60

0.3

0.1

–70

–0.1

–0.3

–80

–90

–0.5

+110°C

+25°C

–40°C

–100

–0.7

0

5

10

15

20

25

30

–220 –180 –140 –100 –60 –20 20

60 100 140 180 220

OBSERVATION RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 141. Observation Receiver DC Offset vs. Observation Receiver

Attenuation, 45 MHz Offset, −10 dBFS Input Signal

Figure 138. Normalized Observation Receiver Flatness vs. Baseband Offset

Frequency, −10 dBFS Input Signal

Rev. 0 | Page 47 of 133

ADRV9029

Data Sheet

–40

–50

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

–45

–50

–55

–60

–65

–70

–75

–80

–85

–90

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–60

–70

–80

–90

–100

–110

–120

800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800

–67.5

–45.0

–22.5

0

22.5

45.0

67.5

OBSERVATION RECEIVER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 142. Observation Receiver DC Offset vs. Observation Receiver

LO Frequency, Attenuation = 0 dB, Sample Rate = 491.52 MSPS

Figure 145. Observation Receiver HD3, Left Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

–40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–50

–60

–50

–60

–70

–80

–90

–100

–110

–120

–100

–110

–120

–112.5

–67.5

–22.5

22.5

67.5

112.5

–67.5

–45.0

–22.5

0

22.5

45.0

67.5

BASEBAND OFFSET FREQUENCY (MHz)

Figure 143. Observation Receiver HD2, Left Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

Figure 146. Observation Receiver HD3, Right Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

–40

90

85

80

75

70

65

60

55

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–50

–60

–70

–80

–90

–100

–110

–120

50

45

40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–112.5

–67.5

–22.5

22.5

67.5

112.5

805 815 825 835 845 855 865 875 885 895 905

BASEBAND OFFSET FREQUENCY (MHz)

TONE 2 FREQUENCY (MHz)

Figure 144. Observation Receiver HD2, Right Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

Figure 147. Observation Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Rev. 0 | Page 48 of 133

Data Sheet

ADRV9029

90

85

80

75

70

65

60

55

100

90

80

70

60

50

40

50

45

40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

805

835

865

895

925

955

985

1015

0

5

10

15

20

25

30

TONE 2 FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 148. Observation Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 151. Observation Receiver IIP2, f1 + f2 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 102 MHz, f2 = 2 MHz

90

80

70

60

50

100

90

80

70

60

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

50

40

10

40

70

100

130

160

190

220

0

5

10

15

20

25

30

TWO-TONE FREQUENCY SPACING (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 149. Observation Receiver IIP2, f1 + f2 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

Figure 152. Observation Receiver IIP2, f1 − f2 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 102 MHz, f2 = 2 MHz

90

80

70

60

40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

36

32

28

24

20

16

12

8

50

40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

4

0

10

40

70

100

130

160

190

220

805

815

825

835

845

855

865

TWO-TONE FREQUENCY SPACING (MHz)

TONE 2 FREQUENCY

Figure 150. Observation Receiver IIP2, f1 − f2 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

Figure 153. Observation Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Rev. 0 | Page 49 of 133

ADRV9029

Data Sheet

40

30

25

20

15

10

5

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

36

32

28

24

20

16

12

8

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

4

0

805

0

10

815

825

835

845

855

865

20

30

40

50

60

70

80

90

100

TWO-TONE FREQUENCY SPACING (MHz)

TONE 2 FREQUENCY

Figure 154. Observation Receiver IIP3, 2f2 + f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 157. Observation Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

40

30

25

20

15

10

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

36

32

28

24

20

16

12

8

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

5

0

4

0

805

835

865

895

925

955

985

1015

10

30

50

70

90

110 130 150 170 190 210

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 155. Observation Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 158. Observation Receiver IIP3, 2f2 + F1 vs. Two-Tone Frequency Spacing,

Both Tones at −13 dBFS, f2 = 2 MHz

40

30

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

36

32

28

24

20

16

12

8

25

20

15

10

5

4

0

805

0

10

835

865

895

925

955

985

1015

30

50

70

90

110

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING, f2 = 2MHz (MHz)

Figure 156. Observation Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 159. Observation Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −13 dBFS, f2 = 2 MHz

Rev. 0 | Page 50 of 133

Data Sheet

ADRV9029

30

25

20

15

10

5

40

35

30

25

20

15

10

5

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

0

10

0

40

70

100

130

160

190

220

0

5

10

15

20

TWO-TONE FREQUENCY SPACING (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 160. Observation Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency Spacing,

Both Tones at −13 dBFS, f2 = 2 MHz

Figure 162. Observation Receiver IIP3, 2f2 − f1 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 122 MHz, f2 = 2 MHz

40

35

30

25

20

15

10

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

5

0

5

10

15

20

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 161. Observation Receiver IIP3, 2f2 + f1 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 122 MHz, f2 = 2 MHz

Rev. 0 | Page 51 of 133

ADRV9029

Data Sheet

1800 MHz BAND

The temperature settings refer to the die temperature. All LO frequencies set to 1800 MHz, unless otherwise noted.

10

9

8

7

6

5

4

3

2

1

0

–100

–110

–120

–130

–140

–150

–160

–170

–180

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+110°C

+25°C

–40°C

1500

1600

1700

1800

1900

2000

0

5

10

15

20

TRANSMITTER LO FREQUENCY (MHz)

TRANSMITTER ATTENUATION (dB)

Figure 166. Transmitter Noise vs. Transmitter Attenuation, 10 MHz Offset

Figure 163. Transmitter Continuous Wave (CW) Output Power vs.

Transmitter LO Frequency, 10 MHz Offset, 0 dB Attenuation

1.0

0

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

SIGNAL

NOISE FLOOR

0.8

0.6

0.4

0.2

0

–10

–20

–30

–40

–50

–60

–70

–80

–90

–100

–0.2

–0.4

–225 –175 –125 –75

–25

25

75

125

175

225

1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300

BASEBAND OFFSET FREQUENCY (MHz)

FREQUENCY (MHz)

Figure 164. Transmitter Output Power Spectrum, TX1, 5 MHz LTE,

10 MHz Offset, −10 dBFS RMS, 1 MHz Resolution Bandwidth, T_J= 25°C

Figure 167. Transmitter Pass Band Flatness vs. Baseband Offset Frequency

–40

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–45

–50

–55

–60

–65

–70

–75

–80

–50

–60

–70

–80

–90

–100

–100 –80 –60 –40 –20

0

20

40

60

80

100

0

5

10

15

20

BASEBAND OFFSET FREQUENCY (MHz)

TRANSMITTER ATTENUATION (dB)

Figure 165. Transmitter Image Rejection Across Large Signal Bandwidth vs.

Baseband Offset Frequency

Figure 168. Adjacent Channel Power Level vs. Transmitter Attenuation,

−10 MHz Baseband Offset, 20 MHz LTE, PAR = 12 dB

Rev. 0 | Page 52 of 133

Data Sheet

ADRV9029

–40

–45

–50

–55

–60

–65

–70

–75

0.05

0.04

0.03

0.02

0.01

0

+110°C

+25°C

–40°C

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–0.01

–0.02

–0.03

–0.04

–0.05

–80

0

5

10

15

20

0

4

8

12

16

20

24

28

32

TRANSMITTER ATTENUATION (dB)

Figure 172. Transmitter Attenuator Step Error vs. Transmitter Attenuation,

10 MHz Offset

Figure 169. Adjacent Channel Power Level vs. Transmitter Attenuation,

90 MHz Baseband Offset, 20 MHz LTE, PAR = 12 dB

–60

–40

+110°C, LOWER HD2

+25°C, LOWER HD2

–40°C, LOWER HD2

+110°C, UPPER HD2

+25°C, UPPER HD2

–40°C, UPPER HD2

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–70

–80

–42

–44

–46

–48

–50

–90

–100

–110

–120

0

2

4

6

8

10

12

14

16

18

20

0

5

10

15

20

TRANSMITTER ATTENUATION (dB)

Figure 173. Transmitter Error Vector Magnitude vs. Transmitter Attenuation,

20 MHz LTE Signal Centered at LO Frequency, Sample Rate = 491.52 MSPS, Loop

Filter Bandwidth = 500 kHz, Loop Filter Phase Margin = 60°

Figure 170. Transmitter Second Harmonic Distortion (HD2) vs. Transmitter

Attenuation, 10 MHz Offset

45

–60

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+110°C, LOWER HD3

+25°C, LOWER HD3

–40°C, LOWER HD3

+110°C, UPPER HD3

+25°C, UPPER HD3

–40°C, UPPER HD3

40

35

30

25

20

15

10

5

–70

–80

–90

–100

–110

–120

0

–5

–10

0

4

8

12

16

20

24

28

32

0

2

4

6

8

10

12

14

16

18

20

TRANSMITTER ATTENUATION SETTING (dB)

TRANSMITTER ATTENUATION (dB)

Figure 174. Transmitter OIP3, 2f1 − f2 vs. Transmitter Attenuation, 15 dB

Digital Back Off per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

Figure 171. Transmitter Third Harmonic Distortion (HD3) vs. Transmitter

Attenuation, 10 MHz Offset

Rev. 0 | Page 53 of 133

ADRV9029

Data Sheet

45

40

35

30

25

20

15

10

5

50

45

40

35

30

25

20

15

10

5

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, Tx1

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

0

–5

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

–10

0

10

0

4

8

12

16

20

24

28

32

30

50

70

90

110

130

150

170

190

TRANSMITTER ATTENUATION SETTING (dB)

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 175. Transmitter OIP3, 2f2 − f1 vs. Transmitter Attenuation, 15 dB

Digital Back Off per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

Figure 178. Transmitter OIP3, 2f1 + f2 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

50

45

40

35

30

25

20

15

50

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

45

40

35

30

25

20

15

10

5

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

10

5

0

10

0

10

30

50

70

90

110

130

150

170

190

30

50

70

90

110

130

150

170

190

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 176. Transmitter OIP3, 2f1 − f2 vs. f1 Baseband Oﬀset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

Figure 179. Transmitter OIP3, 2f2 + f1 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

50

45

40

35

30

25

20

15

100

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

95

90

85

80

75

70

65

60

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

10

5

0

10

30

50

70

90

110

130

150

170

190

1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

TRANSMITTER LO FREQUENCY(MHz)

Figure 177. Transmitter OIP3, 2f2 − f1 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

Figure 180. Transmitter LO Leakage vs. Transmitter LO Frequency

Rev. 0 | Page 54 of 133

Data Sheet

ADRV9029

120

110

100

90

120

110

100

90

Tx1 TO Tx2

Tx2 TO Tx1

Tx3 TO Tx1

Tx4 TO Tx1

Tx1 TO Tx3

Tx2 TO Tx3

Tx3 TO Tx2

Tx4 TO Tx2

Tx1 TO Tx4

Tx2 TO Tx4

Tx3 TO Tx4

Tx4 TO Tx3

80

70

Rx1 TO Rx2

Rx2 TO Rx1

Rx3 TO Rx1

Rx4 TO Rx1

Rx1 TO Rx3

Rx2 TO Rx3

Rx3 TO Rx2

Rx4 TO Rx2

Rx1 TO Rx4

Rx2 TO Rx4

Rx3 TO Rx4

Rx4 TO Rx3

60

50

1600

50

1600

1700

1800

1900

2000

1700

1800

1900

2000

RECEIVER LO FREQUENCY (MHz)

TRANSMITTER LO FREQUENCY (MHz)

Figure 181. Transmitter to Transmitter Isolation vs.

Transmitter LO Frequency

Figure 184. Receiver to Receiver Isolation vs. Receiver LO Frequency

130

120

110

100

90

50

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

45

40

35

30

25

20

15

10

5

80

70

Tx1 TO Rx1

Tx2 TO Rx1

Tx3 TO Rx1

Tx4 TO Rx1

Tx1 TO Rx2

Tx2 TO Rx2

Tx3 TO Rx2

Tx4 TO Rx2

Tx1 TO Rx3

Tx2 TO RX3

Tx3 TO Rx3

Tx4 TO Rx3

Tx1 TO Rx4

Tx2 TO Rx4

Tx3 TO Rx4

Tx4 TO Rx4

60

50

1600

0

1700

1800

1900

2000

0

5

10

15

20

RECEIVER LO FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 182. Transmitter to Receiver Isolation vs. Receiver LO Frequency

Figure 185. Receiver Integrated Noise Figure vs. Receiver Attenuation,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS,

Integration Bandwidth = 500 kHz to 100 MHz

130

120

110

100

90

20

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

18

16

14

12

10

8

80

Tx1 TO ORx1

Tx2 TO ORx1

Tx3 TO ORx1

Tx4 TO ORx1

Tx1 TO ORx3

Tx2 TO ORx3

Tx3 TO ORx3

Tx4 TO ORx3

Tx1 TO ORx2

Tx2 TO ORx2

Tx3 TO ORx2

Tx4 TO ORx2

Tx1 TO ORx4

Tx2 TO ORx4

Tx3 TO ORx4

Tx4 TO ORx4

70

60

50

6

1600

1700

1800

1900

2000

1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300

TRANSMITTER LO FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 183. Transmitter to Observation Receiver Isolation vs. Transmitter

LO Frequency

Figure 186. Receiver Integrated Noise Figure vs. Receiver LO Frequency,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS,

Integration Bandwidth = 500 kHz to 100 MHz

Rev. 0 | Page 55 of 133

ADRV9029

Data Sheet

25

20

19

18

17

16

15

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

20

15

10

5

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0

–100 –80 –60 –40 –20

0

20

40

60

80

100

1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300

BASEBAND OFFSET FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 187. Receiver Integrated Noise Figure vs. Baseband Offset Frequency,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS,

Integrated in 200 kHz Steps

Figure 190. Receiver Gain vs. Receiver LO Frequency, 200 MHz Bandwidth,

Sample Rate = 245.76 MSPS

–40

0.20

+110°C

+25°C

–40°C

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0.15

0.10

–50

–60

–70

0.05

0.00

–0.05

–0.10

–0.15

–0.20

–80

–90

–100

1500

1600

1700

1800

1900

2000

0

5

10

15

20

25

30

RECEIVER LO FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 188. Receiver LO Leakage vs. Receiver LO Frequency,

Attenuation = 0 dB, Sample Rate = 245.76 MSPS

Figure 191. Receiver Gain Step Error vs. Receiver Attenuation,

20 MHz Offset, −5 dBFS Input Signal

20

15

10

5

0.5

+110°C

+25°C

–40°C

0.4

0.3

0.2

0.1

0.0

0

–0.1

–0.2

–0.3

–0.4

–0.5

–5

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–10

–15

0

5

10

15

20

25

30

–100 –80 –60 –40 –20

0

20

40

60

80

100

RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 192. Normalized Receiver Flatness vs. Baseband Offset Frequency,

−5 dBFS Input Signal

Figure 189. Receiver Gain vs. Receiver Attenuation, 20 MHz Offset, 200 MHz

Bandwidth, Sample Rate = 245.76 MSPS

Rev. 0 | Page 56 of 133

Data Sheet

ADRV9029

–40

–50

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–50

–60

–70

–80

–90

–100

–110

–100

–100 –80 –60 –40 –20

0

20

40

60

80

100

1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300

BASEBAND OFFSET FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 193. Receiver Image vs. Baseband Offset Frequency,

Tracking Calibration Active, Sample Rate = 245.76 MSPS

Figure 196. Receiver DC Offset vs. Receiver LO Frequency, 20 MHz Offset,

−5 dBFS Input Signal

–40

–50

–60

–70

–80

–90

–100

–40

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–50

–60

–70

–80

–90

–100

–110

–120

0

5

10

15

20

25

30

–60

–40

–20

0

20

40

60

RECEIVER ATTENUATION (dB)

RECEIVER OFFSET FREQUENCY (MHz)

Figure 194. Receiver Image vs. Receiver Attenuation, 20 MHz Offset, Tracking

Calibration Active, Sample Rate = 245.76 MSPS

Figure 197. Receiver HD2, Left Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

(HD2 Canceller Not Enabled)

–40

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–50

–60

–50

–60

–70

–80

–90

–100

–110

–120

–100

–110

0

5

10

15

20

25

–60

–40

–20

0

20

40

60

RECEIVER ATTENUATION (dB)

RECEIVER OFFSET FREQUENCY (MHz)

Figure 195. Receiver DC Offset vs. Receiver Attenuation, 20 MHz Offset,

−5 dBFS Input Signal

Figure 198. Receiver HD2, Right Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

(HD2 Canceller Not Enabled)

Rev. 0 | Page 57 of 133

ADRV9029

Data Sheet

–40

90

85

80

75

70

65

60

55

50

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–50

–60

–70

–80

–90

–100

–110

–120

–40

–30

–20

–10

0

10

20

30

40

1805 1815 1825 1835 1845 1855 1865 1875 1885 1895

BASEBAND OFFSET FREQUENCY (MHz)

TONE 2 FREQUENCY (MHz)

Figure 199. Receiver HD3, Left Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

Figure 202. Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

–40

90

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–50

–60

85

80

75

70

65

60

55

50

–70

–80

–90

–100

–110

–120

–40

–30

–20

–10

0

10

20

30

40

10

20

30

40

50

60

70

80

90

BASEBAND OFFSET FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 200. Receiver HD3, Right Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

Figure 203. Receiver IIP2, f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

90

80

75

70

65

60

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

85

80

75

70

65

60

55

50

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

55

50

1805

1815

1825

1835

1845

10

20

30

40

50

60

70

80

90

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 201. Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Figure 204. Receiver IIP2, f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Rev. 0 | Page 58 of 133

Data Sheet

ADRV9029

110

40

35

30

25

20

15

10

5

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

100

90

80

70

60

0

1805

0

5

10

15

20

25

30

1810

1815

1820

1825

RECEIVER ATTENUATION (dB)

TONE 2 FREQUENCY (MHz)

Figure 205. Receiver IIP2, f1 + f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

Figure 208. Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

110

100

90

40

35

30

25

20

15

10

5

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

80

70

60

0

5

10

15

20

25

30

1805 1815 1825 1835 1845 1855 1865 1875 1885 1895

RECEIVER ATTENUATION (dB)

TONE 2 FREQUENCY (MHz)

Figure 206. Receiver IIP2, f1 − f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

Figure 209. Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

40

35

30

25

20

15

10

5

40

35

30

25

20

15

10

5

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0

1805

0

1810

1815

1820

1825

1805 1815 1825 1835 1845 1855 1865 1875 1885 1895

TONE 2 FREQUENCY (MHz)

Figure 207. Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Figure 210. Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Rev. 0 | Page 59 of 133

ADRV9029

Data Sheet

35

30

25

20

15

10

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, RX2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

30

25

20

15

10

15

20

25

30

35

40

10

20

30

40

50

60

70

80

90

TWO-TONE FREQUENCY SPACING (MHz)

Figure 211. Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Figure 214. Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

35

–20

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, RX2

+110°C, Rx3

+110°C, Rx4

–23

–26

–29

–32

–35

–38

–41

–44

–47

–50

30

25

20

15

10

20

30

40

50

60

70

80

90

–60 –55 –50 –45 –40 –35 –30 –25 –20 –15 –10 –5

0

TWO-TONE FREQUENCY SPACING (MHz)

RECEIVER INPUT POWER (dBm)

Figure 212. Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Figure 215. Receiver Error Vector Magnitude vs. Receiver Input Power,

20 MHz LTE Signal Centered at LO Frequency, Sample Rate = 245.76 MSPS, Loop

Filter Bandwidth = 500 kHz, Loop Filter Phase Margin = 60°

35

–80

–90

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

30

25

20

15

10

–100

–110

–120

–130

–140

–150

–160

–170

10

15

20

25

30

35

40

100

1k

10k

100k

1M

10M

TWO-TONE FREQUENCY SPACING (MHz)

FREQUENCY OFFSET (Hz)

Figure 213. Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Figure 216. LO Phase Noise vs. Frequency Offset, Loop Bandwidth = 50 kHz,

Phase Margin = 85°

Rev. 0 | Page 60 of 133

Data Sheet

ADRV9029

–80

35

30

25

20

15

10

5

–90

–100

–110

–120

–130

–140

–150

–160

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–170

100

0

–250

1k

10k

100k

1M

10M

–150

–50

50

150

250

FREQUENCY OFFSET (Hz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 217. LO Phase Noise vs. Frequency Offset, Loop Bandwidth = 200 kHz,

Phase Margin = 60°

Figure 220. Observation Receiver Integrated Noise Figure vs. Baseband Offset

Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS,

Integrated in 200 kHz Steps

50

–40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+110°C

+25°C

–40°C

45

40

35

30

25

20

15

10

5

–50

–60

–70

–80

–90

0

–100

1500

0

5

10

15

20

1600

1700

1800

1900

2000

OBSERVATION RECEIVER ATTENUATION (dB)

OBSERVATION RECEIVER LO FREQUENCY (MHz)

Figure 218. Observation Receiver Integrated Noise Figure vs. Observation

Receiver Attenuation, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS,

Integration Bandwidth = 500 kHz to 245.76 MHz

Figure 221. Observation Receiver LO Leakage vs. Observation Receiver

LO Frequency, Attenuation = 0 dB, Sample Rate = 491.52 MSPS

24

20

15

10

5

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

22

20

18

16

14

12

10

0

–5

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–10

–15

1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300

0

5

10

15

20

25

30

OBSERVATION RECEIVER LO FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 219. Observation Receiver Integrated Noise Figure vs. Observation

Receiver LO Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS,

Integration Bandwidth = 500 kHz to 245.76 MHz

Figure 222. Observation Receiver Gain vs. Observation Receiver Attenuation, 45

MHz Offset, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Rev. 0 | Page 61 of 133

ADRV9029

Data Sheet

20

19

18

17

16

–40

–50

–60

–70

–80

–90

–100

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

15

1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300

–225 –175 –125 –75

–25

25

75

125

175

225

OBSERVATION RECEIVER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 223. Observation Receiver Gain vs. Observation Receiver LO

Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Figure 226. Observation Receiver Image vs. Baseband Offset Frequency,

Tracking Calibration Active, Sample Rate = 491.52 MSPS

0.20

–40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

0.15

0.10

0.05

0

–50

–60

–70

–0.05

–0.10

–0.15

–0.20

–80

–90

–100

0

5

10

15

20

25

30

0

5

10

15

20

25

30

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 224. Observation Receiver Gain Step Error vs. Observation Receiver

Attenuation, 45 MHz Offset, −10 dBFS Input Signal

Figure 227. Observation Receiver Image vs. Observation Receiver Attenuation,

45 MHz Offset, Tracking Calibration Active,

Sample Rate = 491.52 MSPS

0.5

–40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+110°C

0.4

0.3

+25°C

–40°C

–47

–54

–61

–68

–75

–82

–89

–96

–103

–110

0.2

0.1

0

–0.1

–0.2

–0.3

–0.4

–0.5

–220 –180 –140 –100 –60 –20 20

60 100 140 180 220

0

5

10

15

20

25

30

BASEBAND OFFSET FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 225. Normalized Observation Receiver Flatness vs. Baseband Offset

Frequency, −10 dBFS Input Signal

Figure 228. Observation Receiver DC Offset vs. Observation Receiver

Attenuation, 45 MHz Offset, −10 dBFS Input Signal

Rev. 0 | Page 62 of 133

Data Sheet

ADRV9029

–40

–50

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–45

–50

–55

–60

–65

–70

–75

–80

–85

–90

–60

–70

–80

–90

–100

–110

–120

1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300

–60

–40

–20

0

20

40

60

OBSERVATION RECEIVER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 229. Observation Receiver DC Offset vs. Observation Receiver

LO Frequency, Attenuation = 0 dB, Sample Rate = 491.52 MSPS

Figure 232. Observation Receiver HD3, Left Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

–40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–50

–60

–50

–60

–70

–80

–90

–100

–110

–120

–100

–110

–120

–100 –80 –60 –40 –20

0

20

40

60

80

100

–60

–40

–20

0

20

40

60

BASEBAND OFFSET FREQUENCY (MHz)

Figure 233. Observation Receiver HD3, Right Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

Figure 230. Observation Receiver HD2, Left Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

90

–40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

85

80

75

70

65

60

55

50

–50

–60

–70

–80

–90

–100

–110

–120

1805 1815 1825 1835 1845 1855 1865 1875 1885 1895 1905

–100 –80 –60 –40 –20

0

20

40

60

80

100

TONE 2 FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 234. Observation Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 231. Observation Receiver HD2, Right Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

Rev. 0 | Page 63 of 133

ADRV9029

Data Sheet

90

110

100

90

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

80

70

60

50

40

80

70

60

50

40

1805

1835

1865

1895

1925

1955

1985

2015

0

5

10

15

20

25

30

TONE 2 FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 235. Observation Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 238. Observation Receiver IIP2, f1 + f2 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 102 MHz, f2 = 2 MHz

90

110

100

90

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

80

70

60

50

40

80

70

60

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

50

40

10

40

70

100

130

160

190

220

0

5

10

15

20

25

30

TWO-TONE FREQUENCY SPACING (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 236. Observation Receiver IIP2, f1 + f2 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

Figure 239. Observation Receiver IIP2, f1 − f2 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 102 MHz, f2 = 2 MHz

80

75

70

65

60

55

50

40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

35

30

25

20

15

10

5

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

45

40

0

10

40

70

100

130

160

190

220

1805

1815

1825

1835

1845

1855

1865

TWO-TONE FREQUENCY SPACING (MHz)

TONE 2 FREQUENCY (MHz)

Figure 237. Observation Receiver IIP2, f1 − f2 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

Figure 240. Observation Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Rev. 0 | Page 64 of 133

Data Sheet

ADRV9029

40

30

25

20

15

10

5

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

35

30

25

20

15

10

5

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

0

1805

0

10

1815

1825

1835

1845

1855

1865

20

30

40

50

60

70

80

90

100

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 241. Observation Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 244. Observation Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

40

30

25

20

15

10

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

35

30

25

20

15

10

5

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

5

0

1805

1835

1865

1895

1925

1955

1985

2015

10

30

50

70

90

110 130 150 170 190 210

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 242. Observation Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 245. Observation Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency Spacing,

Both Tones at −13 dBFS, f2 = 2 MHz

40

30

25

20

15

10

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

36

32

28

24

20

16

12

8

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

5

0

4

0

1805

1835

1865

1895

1925

1955

1985

2015

10

20

30

40

50

60

70

80

90

100

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 243. Observation Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 246. Observation Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −13 dBFS, f2 = 2 MHz

Rev. 0 | Page 65 of 133

ADRV9029

Data Sheet

30

25

20

15

10

60

50

40

30

20

10

0

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

5

0

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

10

40

70

100

130

160

190

220

0

5

10

15

20

25

30

TWO-TONE FREQUENCY SPACING (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 247. Observation Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency Spacing,

Both Tones at −13 dBFS, f2 = 2 MHz

Figure 249. Observation Receiver IIP3, 2f2 − f1 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 122 MHz, f2 = 2 MHz

60

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

50

40

30

20

10

0

5

10

15

20

25

30

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 248. Observation Receiver IIP3, 2f2 + f1 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 122 MHz, f2 = 2 MHz

Rev. 0 | Page 66 of 133

Data Sheet

ADRV9029

2600 MHz BAND

The temperature settings refer to the die temperature. All LO frequencies set to 2600 MHz, unless otherwise noted.

10

9

8

7

6

5

4

3

2

1

0

–100

–110

–120

–130

–140

–150

–160

–170

–180

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+110°C

+25°C

–40°C

1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800

0

5

10

15

20

TRANSMITTER LO FREQUENCY (MHz)

TRANSMITTER ATTENUATION (dB)

Figure 250. Transmitter Continuous Wave Output Power vs. Transmitter LO

Frequency, 10 MHz Offset, 0 dB Attenuation

Figure 253. Transmitter Noise vs. Transmitter Attenuation, 10 MHz Offset

0

1.0

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

SIGNAL

NOISE FLOOR

–10

0.8

0.6

0.4

0.2

0

–20

–30

–40

–50

–60

–70

–80

–90

–0.2

–0.4

–100

2100 2200 2300 2400 2500 2600 2700 2800 2900 3000 3100

–225 –175 –125 –75

–25

25

75

125

175

225

FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 251. Transmitter Output Power Spectrum, Tx1, 5 MHz LTE,

10 MHz Offset, −10 dBFS RMS, 1 MHz Resolution Bandwidth, T_J= 25°C

Figure 254. Transmitter Pass Band Flatness vs. Baseband Offset Frequency

–40

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+110°C

+25°C

–40°C

–45

–50

–55

–60

–65

–70

–75

–80

–50

–60

–70

–80

–90

–100

–100 –80 –60 –40 –20

0

20

40

60

80

100

0

5

10

15

20

BASBAND OFFSET FREQUENCY (MHz)

TRANSMITTER ATTENUATION (dB)

Figure 252. Transmitter Image Rejection Across Large Signal Bandwidth vs.

Baseband Offset Frequency

Figure 255. Adjacent Channel Power Level vs. Transmitter Attenuation,

−10 MHz Baseband Offset, 20 MHz LTE, PAR = 12 dB

Rev. 0 | Page 67 of 133

ADRV9029

Data Sheet

–40

–45

–50

–55

–60

–65

–70

–75

0.05

0.04

0.03

0.02

0.01

0

+110°C

+25°C

–40°C

–0.01

–0.02

–0.03

–0.04

–0.05

+110°C

+25°C

–40°C

–80

0

5

10

15

20

0

4

8

12

16

20

24

28

32

TRANSMITTER ATTENUATION (dB)

Figure 256. Adjacent Channel Power Level vs. Transmitter Attenuation,

90 MHz Baseband Offset, 20 MHz LTE, PAR = 12 dB

Figure 259. Transmitter Attenuator Step Error vs. Transmitter Attenuation,

10 MHz Offset

–60

–40

+110°C, UPPER HD2

+110°C, LOWER HD2

+25°C, UPPER HD2

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

–70

+25°C, LOWER HD2

–42

–44

–46

–48

–50

–40°C, UPPER HD2

–40°C, LOWER HD2

–80

–90

–100

–110

–120

0

2

4

6

8

10

12

14

16

18

20

0

5

10

15

20

TRANSMITTER ATTENUATION (dB)

Figure 257. Transmitter Second Harmonic Distortion (HD2) vs. Transmitter

Attenuation, 10 MHz Offset

Figure 260. Transmitter Error Vector Magnitude vs. Transmitter Attenuation,

20 MHz LTE Signal Centered at LO Frequency, Sample Rate = 491.52 MSPS, Loop

Filter Bandwidth = 500 kHz, Loop Filter Phase Margin = 60°

–60

45

+110°C, LOWER HD3

+25°C, LOWER HD3

–40°C, LOWER HD3

+110°C, UPPER HD3

+25°C, UPPER HD3

–40°C, UPPER HD3

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

40

35

30

25

20

15

10

5

–70

–80

–90

–100

–110

–120

0

–5

–10

0

4

8

12

16

20

24

28

32

0

2

4

6

8

10

12

14

16

18

20

TRANSMITTER ATTENUATION SETTING (dB)

TRANSMITTER ATTENUATION (dB)

Figure 261. Transmitter OIP3, 2f1 − f2 vs. Transmitter Attenuation, 15 dB

Digital Back Off per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

Figure 258. Transmitter Third Harmonic Distortion (HD3) vs. Transmitter

Attenuation, 10 MHz Offset

Rev. 0 | Page 68 of 133

Data Sheet

ADRV9029

45

40

35

30

25

20

15

10

5

50

45

40

35

30

25

20

15

10

5

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

0

–5

–10

0

4

8

12

16

20

24

28

32

10

30

50

70

90

110

130

150

170

190

TRANSMITTER ATTENUATION SETTING (dB)

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 262. Transmitter OIP3, 2f2 − f1 vs. Transmitter Attenuation, 15 dB

Digital Back Off per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

Figure 265. Transmitter OIP3, 2f1 + f2 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

50

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

45

40

35

30

25

20

15

10

5

45

40

35

30

25

20

15

10

5

0

10

0

10

30

50

70

90

110

130

150

170

190

30

50

70

90

110

130

150

170

190

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 263. Transmitter OIP3, 2f1 − f2 vs. f1 Baseband Oﬀset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

Figure 266. Transmitter OIP3, 2f2 + f1 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

50

100

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

45

40

35

30

25

20

15

10

5

95

90

85

80

75

70

65

60

0

10

30

50

70

90

110

130

150

170

190

1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

TRANSMITTER LO FREQUENCY (MHz)

Figure 267. Transmitter LO Leakage vs. Transmitter LO Frequency

Figure 264. Transmitter OIP3, 2f2 − f1 vs. f1 Baseband Oﬀset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

Rev. 0 | Page 69 of 133

ADRV9029

Data Sheet

120

110

100

90

120

110

100

90

80

70

Tx1 TO Tx2

Tx2 TO Tx1

Tx3 TO Tx1

Tx4 TO Tx1

Tx1 TO Tx3

Tx2 TO Tx3

Tx3 TO Tx2

Tx4 TO Tx2

Tx1 TO Tx4

Tx2 TO Tx4

Tx3 TO Tx4

Tx4 TO Tx3

Rx1 TO Rx2

Rx2 TO Rx1

Rx3 TO Rx1

Rx4 TO Rx1

Rx1 TO Rx3

Rx2 TO Rx3

Rx3 TO Rx2

Rx4 TO Rx2

Rx1 TO Rx4

Rx2 TO Rx4

Rx3 TO Rx4

Rx4 TO Rx3

60

50

1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800

TRANSMITTER LO FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 268. Transmitter to Transmitter Isolation vs.

Transmitter LO Frequency

Figure 271. Receiver to Receiver Isolation vs. Receiver LO Frequency

130

120

110

100

90

50

Tx1 TO Rx1

Tx2 TO Rx1

Tx3 TO Rx1

Tx4 TO Rx1

Tx1 TO Rx2

Tx2 TO Rx2

Tx3 TO Rx2

Tx4 TO Rx2

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

45

40

35

30

25

20

15

10

5

80

70

Tx1 TO Rx3

Tx2 TO Rx3

Tx3 TO Rx3

Tx4 TO Rx3

Tx1 TO Rx4

Tx2 TO Rx4

Tx3 TO Rx4

Tx4 TO Rx4

60

50

0

1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800

0

5

10

15

20

RECEIVER LO FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 269. Transmitter to Receiver Isolation vs. Receiver LO Frequency

Figure 272. Receiver Integrated Noise Figure vs. Receiver Attenuation,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS,

Integration Bandwidth = 500 kHz to 100 MHz

130

20

Tx1 TO ORx1

Tx2 TO ORx1

Tx3 TO ORx1

Tx4 TO ORx1

Tx1 TO ORx2

Tx2 TO ORx2

Tx3 TO ORx2

Tx4 TO ORx2

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

120

110

100

90

18

16

14

12

10

8

80

70

Tx1 TO ORx3

Tx1 TO ORx4

Tx2 TO ORx4

Tx3 TO ORx4

Tx4 TO ORx4

Tx2 TO ORx3

Tx3 TO ORx3

Tx4 TO ORx3

60

50

6

1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800

TRANSMITTER LO FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 273. Receiver Integrated Noise Figure vs. Receiver LO Frequency, 200

MHz Bandwidth, Sample Rate = 245.76 MSPS,

Figure 270. Transmitter to Observation Receiver Isolation vs. Transmitter

LO Frequency

Integration Bandwidth = 500 kHz to 100 MHz

Rev. 0 | Page 70 of 133

Data Sheet

ADRV9029

25

20

15

10

5

20

19

18

17

16

15

+110°C

+25°C

–40°C

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

0

–100 –80 –60 –40 –20

0

20

40

60

80

100

1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800

BASEBAND OFFSET FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 274. Receiver Integrated Noise Figure vs. Baseband Offset Frequency,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS, Integrated in 200 kHz Steps

Figure 277. Receiver Gain vs. Receiver LO Frequency, 200 MHz Bandwidth,

Sample Rate = 245.76 MSPS

–40

–50

–60

–70

0.20

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

0.15

0.10

0.05

0

–0.05

–0.10

–0.15

–0.20

–80

+110°C

+25°C

–40°C

–90

–100

1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800

0

5

10

15

20

25

30

RECEIVER LO FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 275. Receiver LO Leakage vs. Receiver LO Frequency,

Attenuation = 0 dB, Sample Rate = 245.76 MSPS

Figure 278. Receiver Gain Step Error vs. Receiver Attenuation,

20 MHz Offset, −5 dBFS Input Signal

20

15

10

5

0.5

0.4

0.3

0.2

0.1

0

–0.1

–0.2

–0.3

–0.4

–0.5

+110°C

+25°C

–40°C

–5

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–10

–15

0

5

10

15

20

25

30

–100 –80 –60 –40 –20

0

20

40

60

80

100

RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 276. Receiver Gain vs. Receiver Attenuation, 20 MHz Offset, 200 MHz

Bandwidth, Sample Rate = 245.76 MSPS

Figure 279. Normalized Receiver Flatness vs. Baseband Offset Frequency,

−5 dBFS Input Signal

Rev. 0 | Page 71 of 133

ADRV9029

Data Sheet

–40

–50

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–50

–60

–70

–80

–90

–100

–110

–100

–100 –80 –60 –40 –20

0

20

40

60

80

100

1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800

BASEBAND OFFSET FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 280. Receiver Image vs. Baseband Offset Frequency,

Tracking Calibration Active, Sample Rate = 245.76 MSPS

Figure 283. Receiver DC Offset vs. Receiver LO Frequency, 20 MHz Offset,

−5 dBFS Input Signal

–40

–50

–60

–70

–80

–90

–100

–40

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–50

–60

–70

–80

–90

–100

–110

–120

0

5

10

15

20

25

30

–60

–40

–20

0

20

40

60

RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 284. Receiver HD2, Left Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

(HD2 Canceller Not Enabled)

Figure 281. Receiver Image vs. Receiver Attenuation, 20 MHz Offset, Tracking

Calibration Active, Sample Rate = 245.76 MSPS

–40

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–50

–60

–50

–60

–70

–80

–90

–100

–110

–120

–100

–110

–60

–40

–20

0

20

40

60

0

5

10

15

20

25

BASEBAND OFFSET FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 285. Receiver HD2, Right Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

(HD2 Canceller Not Enabled)

Figure 282. Receiver DC Offset vs. Receiver Attenuation, 20 MHz Offset,

−5 dBFS Input Signal

Rev. 0 | Page 72 of 133

Data Sheet

ADRV9029

–40

90

85

80

75

70

65

60

55

50

+110°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–50

–60

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–70

–80

–90

–100

–110

–120

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–40

–30

–20

–10

0

10

20

30

40

2605 2615 2625 2635 2645 2655 2665 2675 2685 2695

BASEBAND OFFSET FREQUENCY (MHz)

TONE 2 FREQUENCY (MHz)

Figure 286. Receiver HD3, Left Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

Figure 289. Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

–40

90

85

80

75

70

65

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–50

–60

–70

–80

–90

–100

–110

–120

60

55

50

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–40

–30

–20

–10

0

10

20

30

40

10

20

30

40

50

60

70

80

90

BASEBAND OFFSET FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 290. Receiver IIP2, f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Figure 287. Receiver HD3, Right Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

80

75

70

65

60

90

85

80

75

70

65

60

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

55

50

55

50

10

20

30

40

50

60

70

80

90

2605

2615

2625

2635

2645

TWO-TONE FREQUENCY SPACING (MHz)

TONE 2 FREQUENCY (MHz)

Figure 291. Receiver IIP2, f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Figure 288. Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Rev. 0 | Page 73 of 133

ADRV9029

Data Sheet

110

40

35

30

25

20

15

10

5

+110°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

105

100

95

90

85

80

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

75

70

0

2605

0

5

10

15

20

25

30

2610

2615

2620

2625

RECEIVER ATTENUATION (dB)

TONE 2 FREQUENCY (MHz)

Figure 295. Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Figure 292. Receiver IIP2, f1 + f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

40

35

30

25

20

15

10

5

100

95

90

85

80

75

70

65

60

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

0

2605 2615 2625 2635 2645 2655 2665 2675 2685 2695

0

5

10

15

20

25

30

TONE 2 FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 296. Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Figure 293. Receiver IIP2, f1 − f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

40

35

30

25

20

15

10

5

35

30

25

20

15

10

5

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

0

2605 2615 2625 2635 2645 2655 2665 2675 2685 2695

2605

2610

2615

2620

2625

TONE 2 FREQUENCY (MHz)

Figure 297. Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Figure 294. Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Rev. 0 | Page 74 of 133

Data Sheet

ADRV9029

35

30

25

20

35

30

25

20

15

10

+110°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

15

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

10

15

20

25

30

35

40

10

20

30

40

50

60

70

80

90

TWO-TONE FREQUENCY SPACING (MHz)

Figure 298. Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Figure 301. Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

35

30

25

20

–20

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–23

–26

–29

–32

–35

–38

–41

–44

–47

–50

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

15

10

20

30

40

50

60

70

80

90

–60 –55 –50 –45 –40 –35 –30 –25 –20 –15 –10 –5

0

TWO-TONE FREQUENCY SPACING (MHz)

RECEIVER INPUT POWER (dBm)

Figure 299. Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Figure 302. Receiver Error Vector Magnitude vs. Receiver Input Power,

20 MHz LTE Signal Centered at LO Frequency, Sample Rate = 245.76 MSPS,

Loop Filter Bandwidth = 500 kHz,

Loop Filter Phase Margin = 60°

35

30

25

20

–80

–90

–100

–110

–120

–130

–140

–150

–160

–170

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

15

10

15

20

25

30

35

40

100

1k

10k

100k

1M

10M

TWO-TONE FREQUENCY SPACING (MHz)

FREQUENCY OFFSET (Hz)

Figure 300. Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Figure 303. LO Phase Noise vs. Frequency Offset, Loop Bandwidth = 75 kHz,

Phase Margin = 85°

Rev. 0 | Page 75 of 133

ADRV9029

Data Sheet

–80

35

30

25

20

15

10

5

–90

–100

–110

–120

–130

–140

–150

–160

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–170

100

0

–250

1k

10k

100k

1M

10M

–150

–50

50

150

250

FREQUENCY OFFSET (Hz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 304. LO Phase Noise vs. Frequency Offset, Loop Bandwidth = 500 kHz,

Phase Margin = 60°

Figure 307. Observation Receiver Integrated Noise Figure vs. Baseband Offset

Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS,

Integrated in 200 kHz Steps

50

45

40

35

30

25

20

15

–40

–50

–60

–70

–80

+110°C

+25°C

–40°C

–90

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

10

5

0

–100

0

5

10

15

20

1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800

OBSERVATION RECEIVER ATTENUATION (dB)

OBSERVATION RECEIVER LO FREQUENCY (MHz)

Figure 305. Observation Receiver Integrated Noise Figure vs. Observation

Receiver Attenuation, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS,

Integration Bandwidth = 500 kHz to 245.76 MHz

Figure 308. Observation Receiver LO Leakage vs. Observation Receiver

LO Frequency, Attenuation = 0 dB, Sample Rate = 491.52 MSPS

24

20

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

22

20

18

16

14

12

10

15

10

5

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

0

–5

–10

–15

1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800

0

5

10

15

20

25

30

OBSERVATION RECEIVER LO FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 306. Observation Receiver Integrated Noise Figure vs. Observation

Receiver LO Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS,

Integration Bandwidth = 500 kHz to 245.76 MHz

Figure 309. Observation Receiver Gain vs. Observation Receiver Attenuation, 45

MHz Offset, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Rev. 0 | Page 76 of 133

Data Sheet

ADRV9029

20

–40

–50

–60

–70

–80

–90

–100

+110°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

19

18

17

16

15

1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800

–225 –175 –125 –75

–25

25

75

125

175

225

OBSERVATION RECEIVER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 310. Observation Receiver Gain vs. Observation Receiver LO

Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Figure 313. Observation Receiver Image vs. Baseband Offset Frequency,

Tracking Calibration Active, Sample Rate = 491.52 MSPS

0.20

–40

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

0.15

0.10

0.05

0

–50

–60

–70

–0.05

–0.10

–0.15

–0.20

–80

–90

–100

0

5

10

15

20

25

30

0

5

10

15

20

25

30

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 311. Observation Receiver Gain Step Error vs. Observation Receiver

Attenuation, 45 MHz Offset, −10 dBFS Input Signal

Figure 314. Observation Receiver Image vs. Observation Receiver Attenuation,

45 MHz Offset, Tracking Calibration Active,

Sample Rate = 491.52 MSPS

0.5

0.4

0.3

0.2

0.1

0

–40

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–47

–54

–61

–68

–75

–82

–89

–96

–103

–110

–0.1

–0.2

–0.3

–0.4

–0.5

+110°C

+25°C

–40°C

–220 –180 –140 –100 –60 –20 20

60 100 140 180 220

0

5

10

15

20

25

30

BASEBAND OFFSET FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 312. Normalized Observation Receiver Flatness vs. Baseband Offset

Frequency, −10 dBFS Input Signal

Figure 315. Observation Receiver DC Offset vs. Observation Receiver

Attenuation, 45MHz Offset, −10 dBFS Input Signal

Rev. 0 | Page 77 of 133

ADRV9029

Data Sheet

–40

–50

+110°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–45

–50

–55

–60

–65

–70

–75

–80

–85

–90

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–60

–70

–80

–90

–100

–110

–120

1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800

–60

–40

–20

0

20

40

60

OBSERVATION RECEIVER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 316. Observation Receiver DC Offset vs. Observation Receiver

LO Frequency, Attenuation = 0 dB, Sample Rate = 491.52 MSPS

Figure 319. Observation Receiver HD3, Left Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

–40

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–50

–60

–50

–60

–70

–80

–90

–100

–110

–120

–100

–110

–120

–100 –80 –60 –40 –20

0

20

40

60

80

100

–60

–40

–20

0

20

40

60

BASEBAND OFFSET FREQUENCY (MHz)

5

Figure 317. Observation Receiver HD2, Left Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

Figure 320. Observation Receiver HD3, Right Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

–40

90

85

80

75

70

65

60

55

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–50

–60

–70

–80

–90

–100

–110

–120

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

50

45

40

–100 –80 –60 –40 –20

0

20

40

60

80

100

2605 2615 2625 2635 2645 2655 2665 2675 2685 2695 2705

BASEBAND OFFSET FREQUENCY (MHz)

TONE 2 FREQUENCY (MHz)

Figure 318. Observation Receiver HD2, Right Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

Figure 321. Observation Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Rev. 0 | Page 78 of 133

Data Sheet

ADRV9029

90

80

70

60

110

100

90

80

70

60

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

+110°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

50

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

50

40

2605

40

2635

2665

2695

2725

2755

2785

2815

0

5

10

15

20

25

30

TONE 2 FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 322. Observation Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 325. Observation Receiver IIP2, f1 + f2 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 102 MHz, f2 = 2 MHz

90

80

70

60

110

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

100

90

80

70

60

50

40

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

50

40

10

40

70

100

130

160

190

220

0

5

10

15

20

25

30

TWO-TONE FREQUENCY SPACING (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 323. Observation Receiver IIP2, f1 + f2 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

Figure 326. Observation Receiver IIP2, f1 − f2 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 102 MHz, f2 = 2 MHz

80

75

70

65

60

55

50

40

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

35

30

25

20

15

10

5

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

45

40

0

10

40

70

100

130

160

190

220

2605

2615

2625

2635

2645

2655

2665

TWO-TONE FREQUENCY SPACING (MHz)

TONE 2 FREQUENCY (MHz)

Figure 324. Observation Receiver IIP2, f1 − f2 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

Figure 327. Observation Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Rev. 0 | Page 79 of 133

ADRV9029

Data Sheet

40

35

30

25

20

15

10

5

30

25

20

15

10

5

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

0

2605

0

10

2615

2625

2635

2645

2655

2665

20

30

40

50

60

70

80

90

100

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 328. Observation Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 331. Observation Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

40

30

25

20

15

10

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

35

30

25

20

15

10

5

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

5

0

2605

2635

2665

2695

2725

2755

2785

2815

10

30

50

70

90

110 130 150 170 190 210

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 329. Observation Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 332. Observation Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency Spacing,

Both Tones at −13 dBFS, f2 = 2 MHz

40

30

25

20

15

10

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

36

32

28

24

20

16

12

8

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

5

0

4

0

2605

2635

2665

2695

2725

2755

2785

2815

10

20

30

40

50

60

70

80

90

100

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 330. Observation Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 333. Observation Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −13 dBFS, f2 = 2 MHz

Rev. 0 | Page 80 of 133

Data Sheet

ADRV9029

30

25

20

15

10

5

60

50

40

30

20

10

0

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

0

10

40

70

100

130

160

190

220

0

5

10

15

20

25

30

TWO-TONE FREQUENCY SPACING (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 334. Observation Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency Spacing,

Both Tones at −13 dBFS, f2 = 2 MHz

Figure 336. Observation Receiver IIP3, 2f2 − f1 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 122 MHz, f2 = 2 MHz

60

50

40

30

20

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

10

0

5

10

15

20

25

30

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 335. Observation Receiver IIP3, 2f2 + f1 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 122 MHz, f2 = 2 MHz

Rev. 0 | Page 81 of 133

ADRV9029

Data Sheet

3800 MHZ BAND

The temperature settings refer to the die temperature. All LO frequencies set to 3800 MHz, unless otherwise noted.

10

9

8

7

6

5

4

3

2

1

0

–100

–110

–120

–130

–140

–150

–160

–170

–180

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+110°C

+25°C

–40°C

3300 3400 3500 3600 3700 3800 3900 4000 4100 4200 4300

0

5

10

15

20

TRANSMITTER LO FREQUENCY (MHz)

TRANSMITTER ATTENUATION (dB)

Figure 337. Transmitter Continuous Wave Output Power vs. Transmitter LO

Frequency, 10 MHz Offset, 0 dB Attenuation

Figure 340. Transmitter Noise vs. Transmitter Attenuation,

10 MHz Offset Frequency

1.0

0.8

0.6

0.4

0.2

0

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

SIGNAL

NOISE FLOOR

–10

–20

–30

–40

–50

–60

–70

–80

–90

–0.2

–0.4

–100

–225 –175 –125 –75

–25

25

75

125

175

225

3300 3400 3500 3600 3700 3800 3900 4000 4100 4200 4300

BASEBAND OFFSET FREQUENCY (MHz)

FREQUENCY (MHz)

Figure 341. Transmitter Pass Band Flatness vs. Baseband Offset Frequency

Figure 338. Transmitter Output Power Spectrum, Tx1, 5 MHz LTE,

10 MHz Offset, −10 dBFS RMS, 1 MHz Resolution Bandwidth, T_J= 25°C (Step

at 3600 MHz Due to Spectrum Analyzer)

–40

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–45

–50

–55

–60

–65

–70

–75

–80

–50

–60

–70

–80

–90

–100

0

5

10

15

20

–100 –80 –60 –40 –20

0

20

40

60

80

100

TRANSMITTER ATTENUATION (dB)

BASBAND OFFSET FREQUENCY (MHz)

Figure 342. Adjacent Channel Power Level vs. Transmitter Attenuation,

−10 MHz Baseband Oﬀset, 20 MHz LTE, PAR = 12 dB

Figure 339. Transmitter Image Rejection Across Large Signal Bandwidth vs.

Baseband Offset Frequency

Rev. 0 | Page 82 of 133

Data Sheet

ADRV9029

–40

0.05

0.04

0.03

0.02

0.01

0

–40°C, Tx1

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

–45

–50

–55

–60

–65

–70

–75

–80

–0.01

–0.02

–0.03

–0.04

–0.05

+110°C

+25°C

–40°C

0

5

10

15

20

0

4

8

12

16

20

24

28

32

TRANSMITTER ATTENUATION (dB)

Figure 343. Adjacent Channel Power Level vs. Transmitter Attenuation,

90 MHz Baseband Offset, 20 MHz LTE, PAR = 12 dB

Figure 346. Transmitter Attenuator Step Error vs. Transmitter Attenuation,

10 MHz Offset

–60

–38

+110°C, LOWER HD2

+25°C, LOWER HD2

–40°C, LOWER HD2

+110°C, UPPER HD2

+25°C, UPPER HD2

–40°C, UPPER HD2

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–39

–40

–41

–42

–43

–44

–45

–46

–47

–48

–70

–80

–90

–100

–110

–120

0

2

4

6

8

10

12

14

16

18

20

0

2

4

6

8

10

12

14

16

18

20

TRANSMITTER ATTENUATION (dB)

Figure 344. Transmitter Second Harmonic Distortion (HD2) vs. Transmitter

Attenuation, 10 MHz Offset

Figure 347. Transmitter Error Vector Magnitude vs. Transmitter Attenuation, 20

MHz LTE Signal Centered at LO Frequency, Sample Rate = 491.52 MSPS, Loop

Filter Bandwidth = 200 kHz, Loop Filter Phase Margin = 60°

–60

45

+110°C, LOWER HD3

+25°C, LOWER HD3

–40°C, LOWER HD3

+110°C, UPPER HD3

+25°C, UPPER HD3

–40°C, UPPER HD3

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

40

35

30

25

20

15

10

5

–70

–80

–90

–100

–110

–120

0

–5

–10

0

2

4

6

8

10

12

14

16

18

20

0

4

8

12

16

20

24

28

32

TRANSMITTER ATTENUATION (dB)

TRANSMITTER ATTENUATION SETTING (dB)

Figure 345. Transmitter Third Harmonic Distortion (HD3) vs. Transmitter

Attenuation, 10 MHz Offset

Figure 348. Transmitter OIP3, 2f1 − f2 vs. Transmitter Attenuation,

15 dB Digital Back Off per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

Rev. 0 | Page 83 of 133

ADRV9029

Data Sheet

45

40

35

30

25

20

15

10

5

50

45

40

35

30

25

20

15

10

5

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, Tx1

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

0

–5

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

–10

0

10

0

4

8

12

16

20

24

28

32

30

50

70

90

110

130

150

170

190

TRANSMITTER ATTENUATION SETTING (dB)

F1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 349. Transmitter OIP3, 2f2 − f1 vs. Transmitter Attenuation,

15 dB Digital Back Off per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

Figure 352. Transmitter OIP3, 2f1 + f2 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

50

45

40

35

30

25

20

15

10

50

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

45

40

35

30

25

20

15

10

5

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

5

0

10

0

10

30

50

70

90

110

130

150

170

190

30

50

70

90

110

130

150

170

190

F1 BASEBAND OFFSET TONE FREQUENCY (MHz)

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 350. Transmitter OIP3, 2f1 − f2 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

Figure 353. Transmitter OIP3, 2f2 + f1 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

50

45

40

35

30

25

20

15

100

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

95

90

85

80

75

70

65

60

10

5

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

0

10

30

50

70

90

110

130

150

170

190

3300 3400 3500 3600 3700 3800 3900 4000 4100 4200 4300

F1 BASEBAND OFFSET TONE FREQUENCY (MHz)

TRANSMITTER LO FREQUENCY (MHz)

Figure 351. Transmitter OIP3, 2f2 − f1 vs. f1 Baseband Oﬀset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

Figure 354. Transmitter LO Leakage vs. Transmitter LO Frequency

Rev. 0 | Page 84 of 133

Data Sheet

ADRV9029

120

110

100

90

120

110

100

90

Tx1 TO Tx2

Tx2 TO Tx1

Tx3 TO Tx1

Tx4 TO Tx1

Tx1 TO Tx3

Tx2 TO Tx3

Tx3 TO Tx2

Tx4 TO Tx2

Tx1 TO Tx4

Tx2 TO Tx4

Tx3 TO Tx4

Tx4 TO Tx3

Rx1 TO Rx2

Rx2 TO Rx1

Rx3 TO Rx1

Rx4 TO Rx1

Rx1 TO Rx3

Rx2 TO Rx3

Rx3 TO Rx2

Rx4 TO Rx2

Rx1 TO Rx4

Rx2 TO Rx4

Rx3 TO Rx4

Rx4 TO Rx3

80

70

60

50

3300 3400 3500 3600 3700 3800 3900 4000 4100 4200 4300

TRANSMITTER LO FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 355. Transmitter to Transmitter Isolation vs. Transmitter

LO Frequency

Figure 358. Receiver to Receiver Isolation vs. Receiver LO Frequency

120

110

100

90

50

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

45

40

35

30

25

20

15

10

5

80

70

Tx1 TO Rx1

Tx2 TO Rx1

Tx3 TO Rx1

Tx4 TO Rx1

Tx1 TO Rx2

Tx2 TO Rx2

Tx3 TO Rx2

Tx4 TO Rx2

Tx1 TO Rx3

Tx2 TO Rx3

Tx3 TO Rx3

Tx4 TO Rx3

Tx1 TO Rx4

Tx2 TO Rx4

Tx3 TO Rx4

Tx4 TO Rx4

60

50

0

3300 3400 3500 3600 3700 3800 3900 4000 4100 4200 4300

0

5

10

15

20

RECEIVER LO FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 356. Transmitter to Receiver Isolation vs. Receiver LO Frequency

Figure 359. Receiver Integrated Noise Figure vs. Receiver Attenuation,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS,

Integration Bandwidth = 500 kHz to 100 MHz

130

120

110

100

90

20

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

18

16

14

12

10

8

80

70

Tx1 TO Rx1

Tx2 TO Rx1

Tx3 TO Rx1

Tx4 TO Rx1

Tx1 TO Rx2

Tx2 TO Rx2

Tx3 TO Rx2

Tx4 TO Rx2

Tx1 TO Rx3

Tx2 TO Rx3

Tx3 TO Rx3

Tx4 TO Rx3

Tx1 TO Rx4

Tx2 TO Rx4

Tx3 TO Rx4

Tx4 TO Rx4

60

50

6

3300 3400 3500 3600 3700 3800 3900 4000 4100 4200 4300

TRANSMITTER LO FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 357. Transmitter to Observation Receiver Isolation vs. Transmitter LO

Frequency

Figure 360. Receiver Integrated Noise Figure vs. Receiver LO Frequency,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS,

Integration Bandwidth = 500 kHz to 100 MHz

Rev. 0 | Page 85 of 133

ADRV9029

Data Sheet

25

20

19

18

17

16

15

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

20

15

10

5

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0

–100 –80 –60 –40 –20

0

20

40

60

80

100

3300 3400 3500 3600 3700 3800 3900 4000 4100 4200 4300

BASEBAND OFFSET FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 361. Receiver Integrated Noise Figure vs. Baseband Offset Frequency,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS, Integrated in 200 kHz Steps

Figure 364. Receiver Gain vs. Receiver LO Frequency, 200 MHz Bandwidth,

Sample Rate = 245.76 MSPS

–40

–50

–60

–70

0.20

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0.15

0.10

0.05

0

–0.05

–0.10

–0.15

–0.20

–80

+110°C

+25°C

–40°C

–90

–100

3300 3400 3500 3600 3700 3800 3900 4000 4100 4200 4300

0

5

10

15

20

25

30

RECEIVER LO FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 362. Receiver LO Leakage vs. Receiver LO Frequency, Attenuation =

0 dB, Sample Rate = 245.76 MSPS

Figure 365. Receiver Gain Step Error vs. Receiver Attenuation,

20 MHz Offset, −5 dBFS Input Signal

20

15

10

5

0.5

0.4

0.3

0.2

0.1

0

–0.1

–0.2

–0.3

–0.4

–0.5

+110°C

+25°C

–40°C

–5

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–10

–15

0

5

10

15

20

25

30

–100 –80 –60 –40 –20

0

20

40

60

80

100

RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 363. Receiver Gain vs. Receiver Attenuation, 20 MHz Offset, 200 MHz

Bandwidth, Sample Rate = 245.76 MSPS

Figure 366. Normalized Receiver Flatness vs. Baseband Offset Frequency,

−5 dBFS Input Signal

Rev. 0 | Page 86 of 133

Data Sheet

ADRV9029

–40

–50

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–50

–60

–70

–80

–90

–100

–110

–100

–100 –80 –60 –40 –20

0

20

40

60

80

100

3000

3500

4000

4500

5000

5500

6000

BASEBAND OFFSET FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 367. Receiver Image vs. Baseband Offset Frequency, Tracking

Calibration Active, Sample Rate = 245.76 MSPS

Figure 370. Receiver DC Offset vs. Receiver LO Frequency,

Attenuation = 0 dB, Sample Rate = 245.76 MSPS

–40

–50

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–50

–60

–70

–80

–90

–80

–100

–110

–120

–90

–100

0

5

10

15

20

25

30

–60

–40

–20

0

20

40

60

RECEIVER ATTENUATION (dB)

RECEIVER OFFSET FREQUENCY (MHz)

Figure 368. Receiver Image vs. Receiver Attenuation, 20 MHz Offset, Tracking

Calibration Active, Sample Rate = 245.76 MSPS

Figure 371. Receiver HD2, Left Side vs. Baseband Offset Frequency, −5 dBFS

Input Signal, Distortion Tone Measured Left of 0 Hz (HD2 Canceller Not

Enabled)

–40

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–50

–60

–50

–60

–70

–80

–90

–100

–110

–120

–100

–110

0

5

10

15

20

25

–60

–40

–20

0

20

40

60

RECEIVER ATTENUATION (dB)

RECEIVER OFFSET FREQUENCY (MHz)

Figure 369. Receiver DC Offset vs. Receiver Attenuation, 20 MHz Offset,

−5 dBFS Input Signal, Sample Rate = 245.76 MSPS

Figure 372. Receiver HD2, Right Side vs. Baseband Offset Frequency, −5 dBFS

Input Signal, Distortion Tone Measured Right of 0 Hz (HD2 Canceller Not

Enabled)

Rev. 0 | Page 87 of 133

ADRV9029

Data Sheet

–40

90

85

80

75

70

65

60

55

50

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–50

–60

–70

–80

–90

–100

–110

–120

–40

–30

–20

–10

0

10

20

30

40

3805 3815 3825 3835 3845 3855 3865 3875 3885 3895

RECEIVER OFFSET FREQUENCY (MHz)

TONE 2 FREQUENCY (MHz)

Figure 373. Receiver HD3, Left Side vs. Baseband Offset Frequency, −5 dBFS

Input Signal, Distortion Tone Measured Left of 0 Hz

Figure 376. Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

–40

90

85

80

75

70

65

60

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–50

–60

–70

–80

–90

–100

–110

–120

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

55

50

–40

–30

–20

–10

0

10

20

30

40

10

20

30

40

50

60

70

80

90

RECEIVER OFFSET FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 374. Receiver HD3, Right Side vs. Baseband Offset Frequency, −5 dBFS

Input Signal, Distortion Tone Measured Right of 0 Hz

Figure 377. Receiver IIP2, f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

90

80

75

70

65

60

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

85

80

75

70

65

60

55

50

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

55

50

3805

3815

3825

3835

3845

10

20

30

40

50

60

70

80

90

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 375. Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Figure 378. Receiver IIP2, f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Rev. 0 | Page 88 of 133

Data Sheet

ADRV9029

100

40

36

32

28

24

20

16

12

8

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

95

90

85

80

75

70

65

60

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

4

0

5

10

15

20

25

30

3805

3810

3815

3820

3825

RECEIVER ATTENUATION (dB)

TONE 2 FREQUENCY (MHz)

Figure 379. Receiver IIP2, f1 + f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

Figure 382. Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

110

105

100

95

40

35

30

25

20

15

10

5

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

90

85

80

75

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

70

65

0

60

3805 3815 3825 3835 3845 3855 3865 3875 3885 3895

0

5

10

15

20

25

30

TONE 2 FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 383. Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Figure 380. Receiver IIP2, f1 − f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

40

35

30

25

20

15

10

5

40

35

30

25

20

15

10

5

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0

3805

3805 3815 3825 3835 3845 3855 3865 3875 3885 3895

3810

3815

3820

3825

TONE 2 FREQUENCY (MHz)

Figure 384. Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Figure 381. Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Rev. 0 | Page 89 of 133

ADRV9029

Data Sheet

35

30

25

20

15

35

30

25

20

15

10

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0

10

15

20

25

30

35

40

10

20

30

40

50

60

70

80

90

TWO-TONE FREQUENCY SPACING (MHz)

Figure 388. Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Figure 385. Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

–20

35

30

25

20

15

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–23

–26

–29

–32

–35

–38

–41

–44

–47

–50

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

10

20

30

40

50

60

70

80

90

–60 –55 –50 –45 –40 –35 –30 –25 –20 –15 –10 –5

0

TWO-TONE FREQUENCY SPACING (MHz)

RECEIVER INPUT POWER (dBm)

Figure 386. Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Figure 389. Receiver Error Vector Magnitude vs. Receiver Input Power, 20 MHz

LTE Signal Centered at LO Frequency, Sample Rate = 245.76 MSPS, Loop Filter

Bandwidth = 200 kHz, Loop Filter Phase Margin = 60°

35

–80

–90

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

30

25

20

15

10

–100

–110

–120

–130

–140

–150

–160

–170

10

15

20

25

30

35

40

100

1k

10k

100k

1M

10M

TWO-TONE FREQUENCY SPACING (MHz)

FREQUENCY OFFSET (Hz)

Figure 387. Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Figure 390. LO Phase Noise vs. Frequency Offset,

Loop Bandwidth = 75 kHz, Phase Margin = 85°

Rev. 0 | Page 90 of 133

Data Sheet

ADRV9029

–80

40

35

30

25

20

15

10

5

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–90

–100

–110

–120

–130

–140

–150

–160

–170

100

1k

10k

100k

1M

10M

–250

–150

–50

50

150

250

FREQUENCY OFFSET (Hz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 391. LO Phase Noise vs. Frequency Offset,

Loop Bandwidth = 200 kHz, Phase Margin = 60°

Figure 394. Observation Receiver Integrated Noise Figure vs. Baseband Offset

Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS, Integrated in

200 kHz Steps

50

45

40

35

30

25

20

15

10

5

–40

–50

–60

–70

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–80

+110°C

+25°C

–40°C

–90

0

–100

0

5

10

15

20

3300 3400 3500 3600 3700 3800 3900 4000 4100 4200 4300

OBSERVATION RECEIVER ATTENUATION (dB)

OBSERVATION RECEIVER LO FREQUENCY (MHz)

Figure 392. Observation Receiver Integrated Noise Figure vs. Observation

Receiver Attenuation, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS,

Integration Bandwidth = 500 kHz to 245.76 MHz

Figure 395. Observation Receiver LO Leakage vs. Observation Receiver

LO Frequency, Attenuation = 0 dB, Sample Rate = 491.52 MSPS

28

20

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

26

24

22

20

18

16

14

15

10

5

0

–5

–10

–15

3300 3400 3500 3600 3700 3800 3900 4000 4100 4200 4300

0

5

10

15

20

25

30

OBSERVATION RECEIVER LO FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 393. Observation Receiver Integrated Noise Figure vs. Observation

Receiver LO Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS,

Integration Bandwidth = 500 kHz to 245.76 MHz

Figure 396. Observation Receiver Gain vs. Observation Receiver Attenuation,

45 MHz Offset, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Rev. 0 | Page 91 of 133

ADRV9029

Data Sheet

20

19

18

17

16

15

14

13

–40

–50

–60

–70

–80

–90

–100

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

12

11

10

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

3300 3400 3500 3600 3700 3800 3900 4000 4100 4200 4300

–225 –175 –125 –75

–25

25

75

125

175

225

OBSERVATION RECEIVER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 397. Observation Receiver Gain vs. Observation Receiver

LO Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Figure 400. Observation Receiver Image vs. Baseband Offset Frequency,

Tracking Calibration Active, Sample Rate = 491.52 MSPS

0.20

–40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

0.15

0.10

0.05

0

–50

–60

–70

–0.05

–0.10

–0.15

–0.20

–80

–90

–100

0

5

10

15

20

25

30

0

5

10

15

20

25

30

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 398. Observation Receiver Gain Step Error vs. Observation Receiver

Attenuation, 45 MHz Offset, −10 dBFS Input Signal

Figure 401. Observation Receiver Image vs. Observation Receiver Attenuation,

45 MHz Offset, Tracking Calibration Active,

Sample Rate = 491.52 MSPS

0.5

0.4

0.3

0.2

0.1

0

–40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–47

–54

–61

–68

–75

–82

–89

–96

–103

–110

–0.1

–0.2

–0.3

–0.4

–0.5

+110°C

+25°C

–40°C

–220 –180 –140 –100 –60 –20 20

60 100 140 180 220

0

5

10

15

20

25

30

BASEBAND OFFSET FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 399. Normalized Observation Receiver Flatness vs. Baseband Offset

Frequency, −10 dBFS Input Signal

Figure 402. Observation Receiver DC Offset vs. Observation Receiver

Attenuation, Sample Rate = 491.52 MSPS

Rev. 0 | Page 92 of 133

Data Sheet

ADRV9029

–40

–50

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–45

–50

–55

–60

–65

–70

–75

–80

–85

–90

–60

–70

–80

–90

–100

–110

–120

3300 3400 3500 3600 3700 3800 3900 4000 4100 4200 4300

–60

–40

–20

0

20

40

60

OBSERVATION RECEIVER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 403. Observation Receiver DC Offset vs. Observation Receiver

LO Frequency, Attenuation = 0 dB, Sample Rate = 491.52 MSPS

Figure 406. Observation Receiver HD3, Left Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

–40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–50

–60

–50

–60

–70

–80

–90

–100

–110

–120

–100

–110

–120

–100 –80 –60 –40 –20

0

20

40

60

80

100

–60

–40

–20

0

20

40

60

OBSERVATION RECEIVER OFFSET FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 404. Observation Receiver HD2, Left Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

Figure 407. Observation Receiver HD3, Right Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

–40

90

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

85

80

75

70

65

60

55

50

45

40

–50

–60

–70

–80

–90

–100

–110

–120

–100 –80 –60 –40 –20

0

20

40

60

80

100

3805 3815 3825 3835 3845 3855 3865 3875 3885 3895 3905

OBSERVATION RECEIVER OFFSET FREQUENCY (MHz)

TONE 2 FREQUENCY (MHz)

Figure 405. Observation Receiver HD2, Right Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone

Measured Right of 0 Hz

Figure 408. Observation Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Rev. 0 | Page 93 of 133

ADRV9029

Data Sheet

90

85

80

75

70

65

60

55

50

100

90

80

70

60

50

40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

45

40

3805

3835

3865

3895

3925

3955

3985

4015

0

5

10

15

20

25

30

TONE 2 FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 409. Observation Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 412. Observation Receiver IIP2, f1 + f2 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 102 MHz, f2 = 2 MHz

90

100

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

90

80

70

60

50

40

80

70

60

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

50

40

10

40

70

100

130

160

190

220

0

5

10

15

20

25

30

TWO-TONE FREQUENCY SPACING (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 410. Observation Receiver IIP2, f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −13 dBFS, f2 = 2 MHz

Figure 413. Observation Receiver IIP2, f1 − f2 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 102 MHz, f2 = 2 MHz

80

75

70

65

60

55

50

40

35

30

25

20

15

10

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

45

40

5

0

10

40

70

100

130

160

190

220

3805

3815

3825

3835

3845

3855

3865

TWO-TONE FREQUENCY SPACING (MHz)

TONE 2 FREQUENCY (MHz)

Figure 411. Observation Receiver IIP2, f1 − f2 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

Figure 414. Observation Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Rev. 0 | Page 94 of 133

Data Sheet

ADRV9029

40

35

30

25

20

15

10

30

25

20

15

10

5

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

5

0

3805

0

10

3815

3825

3835

3845

3855

3865

20

30

40

50

60

70

80

90

100

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 415. Observation Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 418. Observation Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

40

35

30

25

20

15

10

30

25

20

15

10

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

5

0

5

0

3805

3835

3865

3995

3925

3955

3985

4015

10

30

50

70

90

110 130 150 170 190 210

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 416. Observation Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 419. Observation Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

40

35

30

25

20

15

10

40

30

20

10

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

5

0

3805

0

10

3835

3865

3995

3925

3955

3985

4015

30

50

70

90

110

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 417. Observation Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 420. Observation Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

Rev. 0 | Page 95 of 133

ADRV9029

Data Sheet

40

60

50

40

30

20

10

0

30

20

10

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

0

10

40

70

100

130

160

190

220

0

5

10

15

20

25

30

TWO-TONE FREQUENCY SPACING (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 421. Observation Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

Figure 423. Observation Receiver IIP3, 2f2 − f1 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 122 MHz, f2 = 2 MHz

60

50

40

30

20

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

10

0

5

10

15

20

25

30

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 422. Observation Receiver IIP3, 2f2 + f1 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 122 MHz, f2 = 2 MHz

Rev. 0 | Page 96 of 133

Data Sheet

ADRV9029

4800 MHZ BAND

The temperature settings refer to the die temperature. All LO frequencies set to 4800 MHz, unless otherwise noted.

10

9

8

7

6

5

4

3

2

1

0

–100

–110

–120

–130

–140

–150

–160

–170

–180

+110°C

+25°C

–40°C

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

4300 4400 4500 4600 4700 4800 4900 5000 5100 5200 5300

0

5

10

15

20

TRANSMITTER LO FREQUENCY (MHz)

TRANSMITTER ATTENUATION (dB)

Figure 424. Transmitter CW Output Power vs. Transmitter LO Frequency,

10 MHz Offset, 0 dB Attenuation

Figure 427. Transmitter Noise vs. Transmitter Attenuation,

10 MHz Offset Frequency

–10

1.0

0.8

0.6

0.4

0.2

0

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

SIGNAL

NOISE FLOOR

–20

–30

–40

–50

–60

–70

–80

–90

–0.2

–100

–0.4

4300 4400 4500 4600 4700 4800 4900 5000 5100 5200 5300

–225 –175 –125 –75

–25

25

125

175

225

75

TRANSMITTER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 425. Transmitter Output Power Spectrum, Tx1, 5 MHz LTE,

10 MHz Offset, −10 dBFS RMS, 1 MHz Resolution Bandwidth, T_J= 25°C

Figure 428. Transmitter Pass Band Flatness vs. Baseband Offset Frequency

–40

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–45

–50

–55

–60

–65

–70

–50

–60

–70

–80

–90

–75

–80

–100

–100 –80 –60 –40 –20

0

20

40

60

80

100

0

5

10

15

20

BASEBAND OFFSET FREQUENCY (MHz)

TRANSMITTER ATTENUATION (dB)

Figure 426. Transmitter Image Rejection Across Large Signal Bandwidth vs.

Baseband Offset Frequency

Figure 429. Adjacent Channel Power Level vs. Transmitter Attenuation,

−10 MHz Baseband Oﬀset, 20 MHz LTE, PAR = 12 dB

Rev. 0 | Page 97 of 133

ADRV9029

Data Sheet

0.05

0.04

0.03

0.02

0.01

0

–40

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+110°C

+25°C

–40°C

–45

–50

–55

–60

–65

–70

–0.01

–0.02

–0.03

–0.04

–0.05

–75

–80

0

4

8

12

16

20

24

28

32

5

10

15

20

TRANSMITTER ATTENUATION (dB)

Figure 430. Adjacent Channel Power Level vs. Transmitter Attenuation,

90 MHz Baseband Offset, 20 MHz LTE, PAR = 12 dB

Figure 433. Transmitter Attenuator Step Error vs. Transmitter Attenuation,

10 MHz Offset

–60

–38

+110°C, LOWER HD2

+25°C, LOWER HD2

–40°C, LOWER HD2

+110°C, UPPER HD2

+25°C, UPPER HD2

–40°C, UPPER HD2

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–39

–40

–41

–42

–43

–44

–45

–46

–47

–48

–70

–80

–90

–100

–110

–120

0

2

4

6

8

10

12

14

16

18

20

0

2

4

6

8

10

12

14

16

18

20

TRANSMITTER ATTENUATION (dB)

Figure 431. Transmitter Second Harmonic Distortion (HD2) vs. Transmitter

Attenuation, 10 MHz Offset

Figure 434. Transmitter Error Vector Magnitude vs. Transmitter Attenuation,

20 MHz LTE Signal Centered at LO Frequency, Sample Rate = 491.52 MSPS, Loop

Filter Bandwidth = 400 kHz, Loop Filter Phase Margin = 60°

45

–60

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+110°C, LOWER HD3

+25°C, LOWER HD3

–40°C, LOWER HD3

+110°C, UPPER HD3

+25°C, UPPER HD3

–40°C, UPPER HD3

40

35

30

25

20

15

10

5

–70

–80

–90

–100

0

–110

–120

–5

–10

0

4

8

12

16

20

24

28

32

0

2

4

6

8

10

12

14

16

18

20

TRANSMITTER ATTENUATION (dB)

TRANSMITTER ATTENUATION SETTING (dB)

Figure 432. Transmitter Third Harmonic Distortion (HD3) vs. Transmitter

Attenuation, 10 MHz Offset

Figure 435. Transmitter OIP3, 2f1 − f2 vs. Transmitter Attenuation,

15 dB Digital Back Off per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

Rev. 0 | Page 98 of 133

Data Sheet

ADRV9029

45

40

35

30

25

20

15

10

5

50

45

40

35

30

25

20

15

10

5

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

0

–5

–10

0

4

8

12

16

20

24

28

32

10

30

50

70

90

110

130

150

170

190

TRANSMITTER ATTENUATION SETTING (dB)

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 436. Transmitter OIP3, 2f2 − f1 vs. Transmitter Attenuation,

15 dB Digital Back Off per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

Figure 439. Transmitter OIP3, 2f1 + f2 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

50

45

40

35

30

25

20

15

10

50

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

45

40

35

30

25

20

15

10

5

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

5

0

10

30

50

70

90

110

130

150

170

190

10

30

50

70

90

110

130

150

170

190

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 437. Transmitter OIP3, 2f1 − f2 vs. f1 Baseband Oﬀset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

Figure 440. Transmitter OIP3, 2f2 + f1 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

50

45

40

35

30

25

20

15

100

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

95

90

85

80

75

70

65

60

10

5

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

0

10

30

50

70

90

110

130

150

170

190

4300 4400 4500 4600 4700 4800 4900 5000 5100 5200 5300

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

TRANSMITTER LO FREQUENCY (MHz)

Figure 438. Transmitter OIP3, 2f2 − f1 vs. f1 Baseband Oﬀset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

Figure 441. Transmitter LO Leakage vs. Transmitter LO Frequency

Rev. 0 | Page 99 of 133

ADRV9029

Data Sheet

120

110

100

90

120

110

100

90

Tx1 TO Tx2

Tx2 TO Tx1

Tx3 TO Tx1

Tx4 TO Tx1

Tx1 TO Tx3

Tx2 TO Tx3

Tx3 TO Tx2

Tx4 TO Tx2

Tx1 TO Tx4

Tx2 TO Tx4

Tx3 TO Tx4

Tx4 TO Tx3

Rx1 TO Rx2

Rx2 TO Rx1

Rx3 TO Rx1

Rx4 TO Rx1

Rx1 TO Rx3

Rx2 TO Rx3

Rx3 TO Rx2

Rx4 TO Rx2

Rx1 TO Rx4

Rx2 TO Rx4

Rx3 TO Rx4

Rx4 TO Rx3

80

70

60

50

4300 4400 4500 4600 4700 4800 4900 5000 5100 5200 5300

TRANSMITTER LO FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 442. Transmitter to Transmitter Isolation vs. Transmitter

LO Frequency

Figure 445. Receiver to Receiver Isolation vs. Receiver LO Frequency

50

120

110

100

90

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

45

40

35

30

25

20

15

10

5

80

70

Tx1 TO Rx1

Tx2 TO Rx1

Tx3 TO Rx1

Tx4 TO Rx1

Tx1 TO Rx2

Tx2 TO Rx2

Tx3 TO Rx2

Tx4 TO Rx2

Tx1 TO Rx3

Tx2 TO Rx3

Tx3 TO Rx3

Tx4 TO Rx3

Tx1 TO Rx4

Tx2 TO Rx4

Tx3 TO Rx4

Tx4 TO Rx4

60

50

0

5

10

15

20

4300 4400 4500 4600 4700 4800 4900 5000 5100 5200 5300

RECEIVER LO FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 443. Transmitter to Receiver Isolation vs. Receiver LO Frequency

Figure 446. Receiver Integrated Noise Figure vs. Receiver Attenuation,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS,

Integration Bandwidth = 500 kHz to 100 MHz

20

130

120

110

100

90

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

18

16

14

12

10

80

70

Tx1 TO ORx1

Tx2 TO ORx1

Tx3 TO ORx1

Tx4 TO ORx1

Tx1 TO ORx2

Tx2 TO ORx2

Tx3 TO ORx2

Tx4 TO ORx2

Tx1 TO ORx3

Tx2 TO ORx3

Tx3 TO ORx3

Tx4 TO ORx3

Tx1 TO ORx4

Tx2 TO ORx4

Tx3 TO ORx4

Tx4 TO ORx4

8

60

50

6

4300 4400 4500 4600 4700 4800 4900 5000 5100 5200 5300

TRANSMITTER LO FREQUENCY (MHz)

4300 4400 4500 4600 4700 4800 4900 5000 5100 5200 5300

RECEIVER LO FREQUENCY (MHz)

Figure 444. Transmitter to Observation Receiver Isolation vs. Transmitter LO

Frequency

Figure 447. Receiver Integrated Noise Figure vs. Receiver LO Frequency,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS,

Integration Bandwidth = 500 kHz to 100 MHz

Rev. 0 | Page 100 of 133

Data Sheet

ADRV9029

25

20

15

10

5

20

19

18

17

16

15

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0

–100 –80 –60 –40 –20

0

20

40

60

80

100

4300 4400 4500 4600 4700 4800 4900 5000 5100 5200 5300

BASEBAND OFFSET FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 448. Receiver Integrated Noise Figure vs. Baseband Offset Frequency,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS, Integrated in 200 kHz

Steps

Figure 451. Receiver Gain vs. Receiver LO Frequency, 200 MHz Bandwidth,

Sample Rate = 245.76 MSPS

–40

0.20

+110°C

+25°C

–40°C

–50

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0.15

0.10

0.05

0

–60

–70

–80

–90

–0.05

–0.10

–0.15

–0.20

–100

0

5

10

15

20

25

30

4300 4400 4500 4600 4700 4800 4900 5000 5100 5200 5300

RECEIVER LO FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 449. Receiver LO Leakage vs. Receiver LO Frequency,

Attenuation = 0 dB, Sample Rate = 245.76 MSPS

Figure 452. Receiver Gain Step Error vs. Receiver Attenuation,

20 MHz Offset, −5 dBFS Input Signal

20

0.5

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C

+25°C

+110°C

0.4

0.3

15

10

5

0.2

0.1

0

–0.1

–0.2

–0.3

–0.4

–0.5

–5

–10

–15

0

5

10

15

20

25

30

–100 –80 –60 –40 –20

0

20

40

60

80

100

RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 450. Receiver Gain vs. Receiver Attenuation, 20 MHz Offset, 200 MHz

Bandwidth, Sample Rate = 245.76 MSPS

Figure 453. Normalized Receiver Flatness vs. Baseband Offset Frequency,

−5 dBFS Input Signal

Rev. 0 | Page 101 of 133

ADRV9029

Data Sheet

–40

–50

–60

–70

–80

–90

–100

–40

–50

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–60

–70

–80

–90

–100

–110

–100 –80 –60 –40 –20

0

20

40

60

80

100

3800 3900 4000 4100 4200 4300 4400 4500 4600 4700 4800

BASEBAND OFFSET FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 454. Receiver Image vs. Baseband Offset Frequency, Tracking

Calibration Active, Sample Rate = 245.76 MSPS

Figure 457. Receiver DC Offset vs. Receiver LO Frequency,

Attenuation = 0 dB, Sample Rate = 245.76 MSPS

–40

–50

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–50

–60

–70

–80

–90

–80

–100

–110

–120

–90

–100

0

5

10

15

20

25

30

–60

–40

–20

0

20

40

60

RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 455. Receiver Image vs. Receiver Attenuation, 20 MHz Offset, Tracking

Calibration Active, Sample Rate = 245.76 MSPS

Figure 458. Receiver HD2, Left Side vs. Baseband Offset Frequency, −5 dBFS

Input Signal, Distortion Tone Measured Left of 0 Hz (HD2 Canceller Not

Enabled)

–40

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–50

–60

–50

–60

–70

–80

–90

–100

–110

–120

–100

–110

0

5

10

15

20

25

–60

–40

–20

0

20

40

60

RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 456. Receiver DC Offset vs. Receiver Attenuation, 20 MHz Offset,

−5 dBFS Input Signal, Sample Rate = 245.76 MSPS

Figure 459. Receiver HD2, Right Side vs. Baseband Offset Frequency, −5 dBFS

Input Signal, Distortion Tone Measured Right of 0 Hz (HD2 Canceller Not

Enabled)

Rev. 0 | Page 102 of 133

Data Sheet

ADRV9029

90

85

80

75

70

65

60

55

50

–40

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–50

–60

–70

–80

–90

–100

–110

–120

–40

–30

–20

–10

0

10

20

30

40

4805 4815 4825 4835 4845 4855 4865 4875 4885 4895

BASEBAND OFFSET FREQUENCY (MHz)

TONE 2 FREQUENCY (MHz)

Figure 460. Receiver HD3, Left Side vs. Baseband Offset Frequency, −5 dBFS

Input Signal, Distortion Tone Measured Left of 0 Hz

Figure 463. Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

90

85

80

75

70

65

60

55

50

–40

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–50

–60

–70

–80

–90

–100

–110

–120

10

20

30

40

50

60

70

80

90

–40

–30

–20

–10

0

10

20

30

40

BASEBAND OFFSET FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 461. Receiver HD3, Right Side vs. Baseband Offset Frequency, −5 dBFS

Input Signal, Distortion Tone Measured Right of 0 Hz

Figure 464. Receiver IIP2, f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

90

80

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

85

80

75

70

65

60

55

50

75

70

65

60

55

50

10

20

30

40

50

60

70

80

90

4805

4815

4825

4835

4845

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 462. Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Figure 465. Receiver IIP2, f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Rev. 0 | Page 103 of 133

ADRV9029

Data Sheet

100

95

90

85

80

75

70

65

60

55

40

35

30

25

20

15

10

5

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

50

0

5

10

15

20

25

30

4805

4810

4815

4820

4825

RECEIVER ATTENUATION (dB)

TONE 2 FREQUENCY (MHz)

Figure 466. Receiver IIP2, f1 + f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

Figure 469. Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

100

95

90

85

80

75

70

65

60

55

50

40

35

30

25

20

15

10

5

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0

5

10

15

20

25

30

4805

4815

4825

4835

4845

4855

4865

4875

4885

RECEIVER ATTENUATION (dB)

TONE 2 FREQUENCY (MHz)

Figure 467. Receiver IIP2, f1 − f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

Figure 470. Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

40

35

30

25

20

15

10

5

40

35

30

25

20

15

10

5

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0

4805

4810

4815

4820

4825

4805 4815 4825 4835 4845 4855 4865 4875 4885 4895

TONE 2 FREQUENCY (MHz)

Figure 468. Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Figure 471. Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Rev. 0 | Page 104 of 133

Data Sheet

ADRV9029

35

30

25

20

15

10

35

30

25

20

15

10

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

10

15

20

25

30

35

40

10

20

30

40

50

60

70

80

90

TWO-TONE FREQUENCY SPACING (MHz)

Figure 472. Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Figure 475. Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

35

30

25

20

–20

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–23

–26

–29

–32

–35

–38

–41

–44

–47

–50

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

15

10

20

30

40

50

60

70

80

90

–60 –55 –50 –45 –40 –35 –30 –25 –20 –15 –10 –5

0

TWO-TONE FREQUENCY SPACING (MHz)

RECEIVER INPUT POWER (dBm)

Figure 473. Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Figure 476. Receiver Error Vector Magnitude vs. Receiver Input Power, 20 MHz

LTE Signal Centered at LO Frequency, Sample Rate = 245.76 MSPS, Loop Filter

Bandwidth = 400 kHz, Loop Filter Phase Margin = 60°

35

30

25

20

–80

–90

–100

–110

–120

–130

–140

–150

–160

–170

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

15

10

15

20

25

30

35

40

100

1k

10k

100k

1M

10M

TWO-TONE FREQUENCY SPACING (MHz)

FREQUENCY OFFSET (Hz)

Figure 474. Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Figure 477. LO Phase Noise vs. Frequency Offset,

Loop Bandwidth = 75 kHz, Phase Margin = 85°

Rev. 0 | Page 105 of 133

ADRV9029

Data Sheet

40

35

30

25

20

15

10

5

–80

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–90

–100

–110

–120

–130

–140

–150

–160

–170

100

–250

–150

–50

50

150

250

1k

10k

100k

1M

10M

BASEBAND OFFSET FREQUENCY (MHz)

FREQUENCY OFFSET (Hz)

Figure 481. Observation Receiver Integrated Noise Figure vs. Baseband Offset

Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS, Integrated in

200 kHz Steps

Figure 478. LO Phase Noise vs. Frequency Offset, Loop Bandwidth = 400 kHz,

Phase Margin = 60°

–40

50

45

40

35

30

25

20

15

+110°C

+25°C

–40°C

–50

–60

–70

–80

–90

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

10

5

–100

0

4300 4400 4500 4600 4700 4800 4900 5000 5100 5200 5300

10

5

10

15

20

OBSERVATION RECEIVER LO FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 482. Observation Receiver LO Leakage vs. Observation Receiver

LO Frequency, Attenuation = 0 dB, Sample Rate = 491.52 MSPS

Figure 479. Observation Receiver Integrated Noise Figure vs. Observation

Receiver Attenuation, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS,

Integration Bandwidth = 500 kHz to 245.76 MHz

20

28

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

15

10

26

24

22

20

18

16

14

5

0

–5

–10

–15

–20

0

5

10

15

20

25

30

4300 4400 4500 4600 4700 4800 4900 5000 5100 5200 5300

OBSERVATION RECEIVER ATTENUATION (dB)

OBSERVATION RECEIVER LO FREQUENCY (MHz)

Figure 483. Observation Receiver Gain vs. Observation Receiver Attenuation,

45 MHz Offset, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Figure 480. Observation Receiver Integrated Noise Figure vs. Observation

Receiver LO Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS,

Integration Bandwidth = 500 kHz to 245.76 MHz

Rev. 0 | Page 106 of 133

Data Sheet

ADRV9029

20

–40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

19

18

17

–50

–60

16

15

14

–70

–80

13

12

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–90

11

10

–100

–225 –175 –125 –75

–25

25

75

125

175

225

4300 4400 4500 4600 4700 4800 4900 5000 5100 5200 5300

OBSERVATION RECEIVER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 484. Observation Receiver Gain vs. Observation Receiver

LO Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Figure 487. Observation Receiver Image vs. Baseband Offset Frequency,

Tracking Calibration Active, Sample Rate = 491.52 MSPS

–40

0.20

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

0.15

0.10

0.05

0

–50

–60

–70

–0.05

–0.10

–80

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–90

–0.15

–0.20

–100

0

5

10

15

20

25

30

0

5

10

15

20

25

30

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 488. Observation Receiver Image vs. Observation Receiver Attenuation,

45 MHz Offset, Tracking Calibration Active,

Figure 485. Observation Receiver Gain Step Error vs. Observation Receiver

Attenuation, 45 MHz Offset, −10 dBFS Input Signal

Sample Rate = 491.52 MSPS

–40

0.5

+110°C

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C

0.4

–47

–54

–61

–68

–75

–82

–40°C

0.3

0.2

0.1

0

–0.1

–0.2

–0.3

–89

–96

T

= +110°C

= +25°C

= –40°C

A

–103

–110

–0.4

–0.5

–220 –180 –140 –100 –60 –20 20

60 100 140 180 220

0

5

10

15

20

25

30

OBSERVATION RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 489. Observation Receiver DC Offset vs. Observation Receiver

Attenuation, Sample Rate = 491.52 MSPS

Figure 486. Normalized Observation Receiver Flatness vs. Baseband Offset

Frequency, −10 dBFS Input Signal

Rev. 0 | Page 107 of 133

ADRV9029

Data Sheet

–40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–45

–50

–55

–60

–65

–70

–50

–60

–70

–80

–90

–75

–80

–85

–90

–100

–110

–120

–60

–40

–20

0

20

40

60

4300 4400 4500 4600 4700 4800 4900 5000 5100 5200 5300

OBSERVATION RECEIVER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 490. Observation Receiver DC Offset vs. Observation Receiver

LO Frequency, Attenuation = 0 dB, Sample Rate = 491.52 MSPS

Figure 493. Observation Receiver HD3, Left Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

–40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–50

–60

–70

–85

–90

–50

–60

–70

–80

–90

–100

–110

–120

–100

–110

–120

–100 –80

–40 –20

0

20

40

60

80

100

–60

–40

–20

0

20

40

60

–60

BASEBAND OFFSET FREQUENCY (MHz)

Figure 491. Observation Receiver HD2, Left Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

Figure 494. Observation Receiver HD3, Right Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

90

–40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

85

–50

–60

–70

–85

–90

80

75

70

65

60

55

50

–100

–110

–120

45

40

–100 –80 –60 –40 –20

0

20

40

60

80

100

4805 4815 4825 4835 4845 4855 4865 4875 4885 4895 4905

BASEBAND OFFSET FREQUENCY (MHz)

TONE 2 FREQUENCY (MHz)

Figure 492. Observation Receiver HD2, Right Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

Figure 495. Observation Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Rev. 0 | Page 108 of 133

Data Sheet

ADRV9029

90

100

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

85

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

90

80

70

60

50

40

80

75

70

65

60

55

50

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

45

40

4805

4835

4865

4895

4925

4955

4985

5015

0

5

10

15

20

25

30

TONE 2 FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 496. Observation Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 499. Observation Receiver IIP2, f1 + f2 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 102 MHz, f2 = 2 MHz

100

90

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

90

80

70

60

80

70

60

50

40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

50

40

10

40

70

100

130

160

190

220

0

5

10

15

20

25

30

OBSERVATION RECEIVER ATTENUATION (dB)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 500. Observation Receiver IIP2, f1 − f2 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 102 MHz, f2 = 2 MHz

Figure 497. Observation Receiver IIP2, f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −13 dBFS, f2 = 2 MHz

40

80

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

35

30

75

70

65

60

55

50

45

40

25

20

15

10

5

0

4805

4815

4825

4835

4845

4855

4865

10

40

70

100

130

160

190

220

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 501. Observation Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 498. Observation Receiver IIP2, f1 − f2 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

Rev. 0 | Page 109 of 133

ADRV9029

Data Sheet

40

30

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

35

30

25

20

15

25

20

15

10

5

10

5

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

0

4805

4815

4825

4835

4845

4855

4865

10

20

30

40

50

60

70

80

90

100

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 502. Observation Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 505. Observation Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

40

35

30

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

35

30

25

20

15

25

20

15

10

5

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

5

0

4805

4835

4865

4895

4925

4955

4985

5015

10

30

50

70

90

110 130 150 170 190 210

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 503. Observation Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 506. Observation Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

40

30

25

20

15

10

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

35

30

25

20

15

10

5

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

5

0

4805

4835

4865

4895

4925

4955

4985

5015

10

30

50

70

90

110

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 504. Observation Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 507. Observation Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

Rev. 0 | Page 110 of 133

Data Sheet

ADRV9029

40

35

30

60

50

40

30

20

10

0

25

20

15

10

5

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

0

5

10

15

20

25

30

10

40

70

100

130

160

190

220

OBSERVATION RECEIVER ATTENUATION (dB)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 510. Observation Receiver IIP3, 2f2 − f1 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 122 MHz, f2 = 2 MHz

Figure 508. Observation Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

60

50

40

30

20

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

10

0

5

10

15

20

25

30

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 509. Observation Receiver IIP3, 2f2 + f1 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 122 MHz, f2 = 2 MHz

Rev. 0 | Page 111 of 133

ADRV9029

Data Sheet

5700 MHZ BAND

The temperature settings refer to the die temperature. All LO frequencies set to 5700 MHz, unless otherwise noted.

10

–100

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

9

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–110

–120

–130

–140

–150

–160

8

7

6

5

4

3

2

+110°C

+25°C

–40°C

–170

–180

1

0

5300

5400

5500

5600

5700

5800

5900

6000

0

5

10

15

20

TRANSMITTER LO FREQUENCY (MHz)

TRANSMITTER ATTENUATION (dB)

Figure 511. Transmitter Continuous Wave Output Power vs. Transmitter LO

Frequency, 10 MHz Offset, 0 dB Attenuation

Figure 514. Transmitter Noise vs. Transmitter Attenuation,

10 MHz Offset Frequency

0

1.0

MEASURED Tx

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

SPECTRUM

ANALYZER NOISE

FLOOR

–10

0.8

0.6

0.4

0.2

0

–20

–30

–40

–50

–60

–70

–80

–0.2

–0.4

–0.6

–90

–100

5300

5400

5500

5600

5700

5800

5900

6000

–225 –175 –125 –75

–25

25

75

125

175

225

FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 512. Transmitter Output Power Spectrum, Tx1, 5 MHz LTE,

10 MHz Offset, −10 dBFS RMS, 1 MHz Resolution Bandwidth, T_J= 25°C

Figure 515. Transmitter Pass Band Flatness vs. Baseband Offset Frequency

–40

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–45

–50

–55

–60

–65

–70

–50

–60

–70

–80

–90

–75

–80

–100

–100 –80 –60 –40 –20

0

20

40

60

80

100

0

5

10

15

20

BASEBAND OFFSET FREQUENCY (MHz)

TRANSMITTER ATTENUATION (dB)

Figure 513. Transmitter Image Rejection Across Large Signal Bandwidth vs.

Baseband Offset Frequency

Figure 516. Adjacent Channel Power Level vs. Transmitter Attenuation,

−10 MHz Baseband Oﬀset, 20 MHz LTE, PAR = 12 dB

Rev. 0 | Page 112 of 133

Data Sheet

ADRV9029

–40

0.05

0.04

0.03

0.02

0.01

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–45

–50

–55

–60

–65

–70

0

–0.01

–0.02

–0.03

–75

–0.04

–0.05

–80

0

5

10

15

20

0

4

8

12

16

20

24

28

32

TRANSMITTER ATTENUATION (dB)

Figure 520. Transmitter Attenuator Step Error vs. Transmitter Attenuation,

10 MHz Offset

Figure 517. Adjacent Channel Power Level vs. Transmitter Attenuation,

90 MHz Baseband Offset, 20 MHz LTE, PAR = 12 dB

–60

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+110°C, LOWER HD2

+25°C, LOWER HD2

–40°C, LOWER HD2

+110°C, UPPER HD2

+25°C, UPPER HD2

–40°C, UPPER HD2

–70

–80

–90

–100

–110

–120

0

2

4

6

8

10

12

14

16

18

20

0

2

4

6

8

10

12

14

16

18

20

TRANSMITTER ATTENUATION (dB)

Figure 518. Transmitter Second Harmonic Distortion (HD2) vs. Transmitter

Attenuation, 10 MHz Offset

Figure 521. Transmitter Error Vector Magnitude vs. Transmitter Attenuation,

20 MHz LTE Signal Centered at LO Frequency, Sample Rate = 491.52 MSPS, Loop

Filter Bandwidth = 400 kHz, Loop Filter Phase Margin = 60°

–60

45

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+110°C, LOWER HD3

+25°C, LOWER HD3

–40°C, LOWER HD3

+110°C, UPPER HD3

+25°C, UPPER HD3

–40°C, UPPER HD3

40

35

30

–70

–80

–90

25

20

15

10

5

–100

0

–110

–120

–5

–10

0

2

4

6

8

10

12

14

16

18

20

0

4

8

12

16

20

24

28

32

TRANSMITTER ATTENUATION (dB)

Figure 519. Transmitter Third Harmonic Distortion (HD3) vs. Transmitter

Attenuation, 10 MHz Offset

Figure 522. Transmitter OIP3, 2f1 − f2 vs. Transmitter Attenuation,

15 dB Digital Back Off per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

Rev. 0 | Page 113 of 133

ADRV9029

Data Sheet

45

40

35

30

50

45

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

40

35

30

25

20

25

20

15

10

5

15

10

0

5

0

–5

–10

0

4

8

12

16

20

24

28

32

10

30

50

70

90

110

130

150

170

190

TRANSMITTER ATTENUATION (dB)

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 523. Transmitter OIP3, 2f2 − f1 vs. Transmitter Attenuation,

15 dB Digital Back Off per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

Figure 526. Transmitter OIP3, 2f1 + f2 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

50

45

50

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

45

40

35

30

40

35

30

25

20

25

20

15

10

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

5

0

5

0

10

30

50

70

90

110

130

150

170

190

10

30

50

70

90

110

130

150

170

190

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 524. Transmitter OIP3, 2f1 − f2 vs. f1 Baseband Oﬀset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

Figure 527. Transmitter OIP3, 2f2 + f1 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

50

45

100

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

95

90

40

35

30

85

80

75

70

25

20

15

10

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

65

60

5

0

10

30

50

70

90

110

130

150

170

190

5300

5400

5500

5600

5700

5800

5900

6000

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

TRANSMITTER LO FREQUENCY(MHz)

Figure 525. Transmitter OIP3, 2f2 − f1 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Back Off per Tone

Figure 528. Transmitter LO Leakage vs. Transmitter LO Frequency

Rev. 0 | Page 114 of 133

Data Sheet

ADRV9029

120

110

100

90

120

110

100

90

Tx1 TO Tx2

Tx2 TO Tx1

Tx3 TO Tx1

Tx4 TO Tx1

Tx1 TO Tx3

Tx2 TO Tx3

Tx3 TO Tx2

Tx4 TO Tx2

Tx1 TO Tx4

Tx2 TO Tx4

Tx3 TO Tx4

Tx4 TO Tx3

Rx1 TO Rx2

Rx2 TO Rx1

Rx3 TO Rx1

Rx4 TO Rx1

Rx1 TO Rx3

Rx2 TO Rx3

Rx3 TO Rx2

Rx4 TO Rx2

Rx1 TO Rx4

Rx2 TO Rx4

Rx3 TO Rx4

Rx4 TO Rx3

80

70

60

50

80

70

60

50

5300

5400

5500

5600

5700

5800

5900

6000

5300

5400

5500

5600

5700

5800

5900

6000

TRANSMITTER LO FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 529. Transmitter to Transmitter Isolation vs. Transmitter

LO Frequency

Figure 532. Receiver to Receiver Isolation vs. Receiver LO Frequency

120

50

45

Tx1 TO Rx1

Tx2 TO Rx1

Tx3 TO Rx1

Tx4 TO Rx1

Tx1 TO Rx2

Tx2 TO Rx2

Tx3 TO Rx2

Tx4 TO Rx2

Tx1 TO Rx3

Tx2 TO Rx3

Tx3 TO Rx3

Tx4 TO Rx3

Tx1 TO Rx4

Tx2 TO Rx4

Tx3 TO Rx4

Tx4 TO Rx4

110

100

90

40

35

30

25

20

80

70

60

50

15

10

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

5

0

5300

5400

5500

5600

5700

5800

5900

6000

0

5

10

15

20

RECEIVER LO FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 530. Transmitter to Receiver Isolation vs. Receiver LO Frequency

Figure 533. Receiver Integrated Noise Figure vs. Receiver Attenuation,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS,

Integration Bandwidth = 500 kHz to 100 MHz

130

20

18

16

14

Tx1 TO ORx1

Tx2 TO ORx1

Tx3 TO ORx1

Tx4 TO ORx1

Tx1 TO ORx2

Tx2 TO ORx2

Tx3 TO ORx2

Tx4 TO ORx2

Tx1 TO ORx3

Tx2 TO ORx3

Tx3 TO ORx3

Tx4 TO ORx3

Tx1 TO ORx4

Tx2 TO ORx4

Tx3 TO ORx4

Tx4 TO ORx4

120

110

100

90

12

10

80

70

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

8

60

50

6

5300

5400

5500

5600

5700

5800

5900

6000

5300

5400

5500

5600

5700

5800

5900

6000

TRANSMITTER LO FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHZ)

Figure 531. Transmitter to Observation Receiver Isolation vs. Transmitter LO

Frequency

Figure 534. Receiver Integrated Noise Figure vs. Receiver LO Frequency,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS, Integration Bandwidth =

500 kHz to 100 MHz

Rev. 0 | Page 115 of 133

ADRV9029

Data Sheet

25

20

15

10

20

19

18

17

16

15

14

13

12

5

0

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

11

10

–100 –80 –60 –40 –20

0

20

40

60

80

100

5300

5400

5500

5600

5700

5800

5900

6000

BASEBAND OFFSET FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 535. Receiver Integrated Noise Figure vs. Baseband Offset Frequency,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS, Integrated in 200 kHz

Steps

Figure 538. Receiver Gain vs. Receiver LO Frequency, 200 MHz Bandwidth,

Sample Rate = 245.76 MSPS

–40

–50

–60

–70

–80

–90

0.20

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0.15

0.10

0.05

0

–0.05

–0.10

–0.15

–0.20

T

= +110°C

= +25°C

= –40°C

A

–100

5300

5400

5500

5600

5700

5800

5900

6000

0

5

10

15

20

25

30

RECEIVER LO FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 536. Receiver LO Leakage vs. Receiver LO Frequency,

Attenuation = 0 dB, Sample Rate = 245.76 MSPS

Figure 539. Receiver Gain Step Error vs. Receiver Attenuation,

20 MHz Offset, −5 dBFS Input Signal

20

0.5

0.4

0.3

0.2

0.1

0.0

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

15

10

5

0

–0.1

–5

–10

–15

–0.2

–0.3

–0.4

–0.5

+110°C

+25°C

–40°C

0

5

10

15

20

25

30

–100 –80 –60 –40 –20

0

20

40

60

80

100

RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 537. Receiver Gain vs. Receiver Attenuation, 20 MHz Offset, 200 MHz

Bandwidth, Sample Rate = 245.76 MSPS

Figure 540. Normalized Receiver Flatness vs. Baseband Offset Frequency,

−5 dBFS Input Signal

Rev. 0 | Page 116 of 133

Data Sheet

ADRV9029

–40

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–50

–60

–50

–60

–70

–80

–90

–100

–110

–100

–100 –80 –60 –40 –20

0

20

40

60

80

100

5300

5400

5500

5600

5700

5800

5900

6000

BASEBAND OFFSET FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHZ)

Figure 541. Receiver Image vs. Baseband Offset Frequency, Tracking

Calibration Active, Sample Rate = 245.76 MSPS

Figure 544. Receiver DC Offset vs. Receiver LO Frequency,

Attenuation = 0 dB, Sample Rate = 245.76 MSPS

–40

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–50

–60

–50

–60

–70

–80

–90

–100

–110

–120

–90

–100

0

5

10

15

20

25

30

–60

–40

–20

0

20

40

60

RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 542. Receiver Image vs. Receiver Attenuation, 20 MHz Offset, Tracking

Calibration Active, Sample Rate = 245.76 MSPS

Figure 545. Receiver HD2, Left Side vs. Baseband Offset Frequency, −5 dBFS

Input Signal, Distortion Tone Measured Left of 0 Hz (HD2 Canceller Not

Enabled)

–40

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–50

–60

–50

–60

–70

–80

–70

–80

–90

–100

–110

–100

–110

–120

0

5

10

15

20

25

–60

–40

–20

0

20

40

60

RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 543. Receiver DC Offset vs. Receiver Attenuation, 20 MHz Offset,

−5 dBFS Input Signal, Sample Rate = 245.76 MSPS

Figure 546. Receiver HD2, Right Side vs. Baseband Offset Frequency, −5 dBFS

Input Signal, Distortion Tone Measured Right of 0 Hz (HD2 Canceller Not

Enabled)

Rev. 0 | Page 117 of 133

ADRV9029

Data Sheet

–40

90

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–50

–60

85

80

75

70

65

60

55

50

–70

–80

–90

–100

–110

–120

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40

–30

–20

–10

0

10

20

30

40

5705 5715 5725 5735 5745 5755 5765 5775 5785 5795

BASEBAND OFFSET FREQUENCY (MHz)

TONE 2 FREQUENCY (MHz)

Figure 547. Receiver HD3, Left Side vs. Baseband Offset Frequency, −5 dBFS

Input Signal, Distortion Tone Measured Left of 0 Hz

Figure 550. Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

–40

90

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–50

–60

85

80

75

70

65

60

55

50

–70

–80

–90

–100

–110

–120

–40

–30

–20

–10

0

10

20

30

40

10

20

30

40

50

60

70

80

90

BASEBAND OFFSET FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 548. Receiver HD3, Right Side vs. Baseband Offset Frequency, −5 dBFS

Input Signal, Distortion Tone Measured Right of 0 Hz

Figure 551. Receiver IIP2, f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

90

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

85

80

75

70

65

60

55

50

85

80

75

70

65

60

55

50

5705

5715

5725

5735

5745

10

20

30

40

50

60

70

80

90

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 549. Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Figure 552. Receiver IIP2, f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Rev. 0 | Page 118 of 133

Data Sheet

ADRV9029

100

40

95

90

85

80

35

30

25

20

15

10

5

75

70

65

60

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

55

50

0

5

10

15

20

25

30

5705

5710

5715

5720

5725

RECEIVER ATTENUATION (dB)

TONE 2 FREQUENCY (MHz)

Figure 553. Receiver IIP2, f1 + f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

Figure 556. Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

100

40

95

90

85

80

35

30

25

20

15

10

5

75

70

65

60

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

55

50

0

5

10

15

20

25

30

5705

5715 5725

5735

5745 5755

5765

5775

5785

RECEIVER ATTENUATION (dB)

TONE 2 FREQUENCY (MHz)

Figure 554. Receiver IIP2, f1 − f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

Figure 557. Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

40

35

30

25

20

15

10

5

35

30

25

20

15

10

5

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0

5705

5710

5715

5720

5725

5705 5715 5725 5735 5745 5755 5765 5775 5785 5795

TONE 2 FREQUENCY (MHz)

Figure 555. Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Figure 558. Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, f1 = f2 + 2 MHz

Rev. 0 | Page 119 of 133

ADRV9029

Data Sheet

35

30

25

20

15

30

25

20

15

10

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

10

20

30

40

50

60

70

80

90

15

20

25

30

35

40

TWO-TONE FREQUENCY SPACING (MHz)

Figure 562. Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Figure 559. Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

–20

35

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–23

–26

–29

–32

–35

30

25

20

–38

–41

–44

–47

–50

15

10

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–60 –55 –50 –45 –40 –35 –30 –25 –20 –15 –10

5

0

10

20

30

40

50

60

70

80

90

RECEIVER INPUT POWER (dBm)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 563. Receiver Error Vector Magnitude vs. Receiver Input Power, 20 MHz

LTE Signal Centered at LO Frequency, Sample Rate = 245.76 MSPS, Loop Filter

Bandwidth = 400 kHz, Loop Filter Phase Margin = 60°

Figure 560. Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

–80

–90

35

30

25

20

–100

–110

–120

–130

15

10

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–140

–150

100

1k

10k

100k

1M

10M

10

15

20

25

30

35

40

FREQUENCY OFFSET (Hz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 564. LO Phase Noise vs. Frequency Offset, Loop Bandwidth = 75 kHz,

Phase Margin = 85°

Figure 561. Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, f2 = 2 MHz

Rev. 0 | Page 120 of 133

Data Sheet

ADRV9029

40

35

30

–80

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–90

–100

25

20

15

10

5

–110

–120

–130

–140

–150

–250

–150

–50

50

150

250

100

1k

10k

100k

1M

10M

BASEBAND OFFSET FREQUENCY (MHz)

FREQUENCY OFFSET (Hz)

Figure 568. Observation Receiver Integrated Noise Figure vs. Baseband Offset

Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS, Integrated in

200 kHz Steps

Figure 565. LO Phase Noise vs. Frequency Offset, Loop Bandwidth = 500 kHz,

Phase Margin = 60°

–40

50

45

–50

–60

–70

–80

–90

40

35

30

25

20

15

10

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

T

= +110°C

= +25°C

= –40°C

A

5

0

–100

5300

5400

5500

5600

5700

5800

5900

6000

0

5

10

15

20

OBSERVATION RECEIVER LO FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 569. Observation Receiver LO Leakage vs. Observation Receiver

LO Frequency, Attenuation = 0 dB, Sample Rate = 491.52 MSPS

Figure 566. Observation Receiver Integrated Noise Figure vs. Observation

Receiver Attenuation, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS,

Integration Bandwidth = 500 kHz to 245.76 MHz

20

28

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

15

10

5

26

24

22

20

18

16

14

0

–5

–10

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–15

–20

5300

5400

5500

5600

5700

5800

5900

6000

0

5

10

15

20

25

30

OBSERVATION RECEIVER LO FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 567. Observation Receiver Integrated Noise Figure vs. Observation

Receiver LO Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS,

Integration Bandwidth = 500 kHz to 245.76 MHz

Figure 570. Observation Receiver Gain vs. Observation Receiver Attenuation,

45 MHz Offset, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Rev. 0 | Page 121 of 133

ADRV9029

Data Sheet

20

–40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

19

18

17

–50

–60

16

15

14

–70

–80

13

12

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–90

11

10

–100

5300

5400

5500

5600

5700

5800

5900

6000

–225 –175 –125 –75

–25

25

75

125

175

225

OBSERVATION RECEIVER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 571. Observation Receiver Gain vs. Observation Receiver

LO Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Figure 574. Observation Receiver Image vs. Baseband Offset Frequency,

Tracking Calibration Active, Sample Rate = 491.52 MSPS

0.20

–40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

0.15

0.10

0.05

0

–50

–60

–70

–0.05

–0.10

–0.15

–0.20

–80

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–90

–100

0

5

10

15

20

25

30

0

5

10

15

20

25

30

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 572. Observation Receiver Gain Step Error vs. Observation Receiver

Attenuation, 45 MHz Offset, −10 dBFS Input Signal

Figure 575. Observation Receiver Image vs. Observation Receiver

Attenuation, 20 MHz Offset, Tracking Calibration Active,

Sample Rate = 491.52 MSPS

0.5

0.4

0.3

0.2

0.1

0

–40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–47

–54

–61

–68

–75

–82

–0.1

–0.2

–89

–96

–0.3

+110°C

+25°C

–40°C

–0.4

–103

–110

–0.5

–220 –180 –140 –100 –60 –20 20

60 100 140 180 220

0

5

10

15

20

25

30

BASEBAND OFFSET FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 573. Normalized Observation Receiver Flatness vs. Baseband Offset

Frequency, −10 dBFS Input Signal

Figure 576. Observation Receiver DC Offset vs. Observation Receiver

Attenuation, Sample Rate = 491.52 MSPS

Rev. 0 | Page 122 of 133

Data Sheet

ADRV9029

–40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–45

–50

–55

–60

–65

–70

–50

–60

–70

–80

–90

–75

–80

–85

–90

–100

–110

–120

5300

5400

5500

5600

5700

5800

5900

6000

–60

–40

–20

0

20

40

60

OBSERVATION RECEIVER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 577. Observation Receiver DC Offset vs. Observation Receiver

LO Frequency, Attenuation = 0 dB, Sample Rate = 491.52 MSPS

Figure 580. Observation Receiver HD3, Left Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

–40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–50

–60

–70

–85

–90

–50

–60

–70

–80

–90

–100

–110

–120

–100

–110

–120

–100 –80 –60 –40 –20

0

20

40

60

80

100

–60

–40

–20

0

20

40

60

BASEBAND OFFSET FREQUENCY (MHz)

Figure 578. Observation Receiver HD2, Left Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

Figure 581. Observation Receiver HD3, Right Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

–40

90

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–50

–60

–70

–85

–90

85

80

75

70

65

60

55

50

–100

–110

–120

45

40

–100 –80 –60 –40 –20

0

20

40

60

80

100

5705 5715 5725 5735

5755 5765 5775 5785 5795 5805

5745

BASEBAND OFFSET FREQUENCY (MHz)

TONE 2 FREQUENCY (MHz)

Figure 579. Observation Receiver HD2, Right Side vs. Baseband Offset

Frequency, −10 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

Figure 582. Observation Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Rev. 0 | Page 123 of 133

ADRV9029

Data Sheet

90

85

100

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

90

80

70

60

50

40

80

75

70

65

60

55

50

45

40

5705

5735

5765

5795

5825

5855

5885

5915

0

5

10

15

20

25

30

TONE 2 FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 583. Observation Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 586. Observation Receiver IIP2, f1 + f2 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 102 MHz, f2 = 2 MHz

90

100

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

85

90

80

70

60

80

75

70

65

60

55

50

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

50

40

45

40

10

40

70

100

130

160

190

220

0

5

10

15

20

25

30

TWO-TONE FREQUENCY SPACING (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 584. Observation Receiver IIP2, f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −13 dBFS, f2 = 2 MHz

Figure 587. Observation Receiver IIP2, f1 − f2 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 102 MHz, f2 = 2 MHz

80

40

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

75

70

65

60

55

50

35

30

25

20

15

10

5

45

40

0

5705

10

40

70

100

130

160

190

220

5715

5725

5735

5745

5755

5765

TWO-TONE FREQUENCY SPACING (MHz)

TONE 2 FREQUENCY (MHz)

Figure 585. Observation Receiver IIP2, f1 − f2 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

Figure 588. Observation Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Rev. 0 | Page 124 of 133

Data Sheet

ADRV9029

40

30

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

35

30

25

20

15

25

20

15

10

5

10

5

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

0

5705

0

10

5715

5725

5735

5745

5755

5765

20

30

40

50

60

70

80

90

100

TONE 2 FREQUENCY (MHz)

TWO TONE FREQUENCY SPACING (MHz)

Figure 589. Observation Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 592. Observation Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

40

35

30

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

35

30

25

20

15

25

20

15

10

5

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

5

0

5705

5735

5765

5795

5825

5855

5885

5915

10

30

50

70

90

110 130 150 170 190 210

TONE 2 FREQUENCY (MHz)

TWO TONE FREQUENCY SPACING (MHz)

Figure 590. Observation Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 593. Observation Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

40

30

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

35

30

25

20

25

20

15

10

5

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

5

0

5705

5735

5765

5795

5825

5855

5885

5915

10

30

50

70

90

110

TONE 2 FREQUENCY (MHz)

TWO TONE FREQUENCY SPACING (MHz)

Figure 591. Observation Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −13 dBFS, f1 = f2 + 2 MHz

Figure 594. Observation Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

Rev. 0 | Page 125 of 133

ADRV9029

Data Sheet

40

35

30

60

50

40

30

20

10

0

25

20

15

10

5

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

0

10

30

50

70

90

110 130 150 170 190 210

0

5

10

15

20

25

30

TWO-TONE FREQUENCY SPACING (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 595. Observation Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency

Spacing, Both Tones at −13 dBFS, f2 = 2 MHz

Figure 597. Observation Receiver IIP3, 2f2 − f1 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 122 MHz, f2 = 2 MHz

60

50

40

30

20

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

10

0

5

10

15

20

25

30

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 596. Observation Receiver IIP3, 2f2 + f1 vs. Observation Receiver

Attenuation, Both Tones at −13 dBFS, f1 = 122 MHz, f2 = 2 MHz

Rev. 0 | Page 126 of 133

Data Sheet

ADRV9029

THEORY OF OPERATION

Two gain control options are available, as follows:

GENERAL

The ADRV9029 is a highly integrated RF transceiver capable of

configuration for a wide range of applications. The device

integrates all the RF, mixed-signal, and digital blocks necessary

to provide all transmitter, traffic receiver, and observation

receiver functions in a single device. Programmability allows

the device to be adapted for use in many 3G/4G/5G cellular

standards in frequency division duplex (FDD) and time

division duplex (TDD) modes.



Users can implement their own gain control algorithms

using their baseband processor to manage manual gain

control mode

Users can use the on-chip automatic gain control (AGC)

system.



Performance is optimized by mapping each gain control setting

to specific attenuation levels at each adjustable gain block in the

receive signal path. Additionally, each channel contains inde-

pendent receive signal strength indication (RSSI) measurement

capability, dc offset tracking, and all the circuitry necessary for

self calibration.

Four observation receiver channels monitor the transmitter

outputs and provide tracking correction of dc offset,

quadrature error, and transmitter LO leakage to maintain a high

performance level under varying temperatures and input signal

conditions. Firmware supplied with the device implements all

initialization and calibration with no user interaction. Additionally,

the device includes test modes allowing system designers to

debug designs during prototyping and to optimize radio

configurations.

The receivers include analog-to-digital converters (ADCs) and

adjustable sample rates that produce data streams from the

received signals. The signals can be conditioned further by a

series of decimation filters and a programmable FIR filter with

additional decimation settings. The sample rate of each digital

filter block is adjustable by changing decimation factors to

produce the desired output data rate. All receiver outputs are

connected to the SERDES block, where the data is formatted

and serialized for transmission to the baseband processor.

The ADRV9029 contains four high speed serial interface

(SERDES) links for the transmit chain and four high speed

links shared by the receiver and observation receiver chains

(JESD204B Subclass 1 compliant and supports JESD204C).

OBSERVATION RECEIVER

TRANSMITTER

The ADRV9029 provides four independent observation

receiver inputs. These inputs are similar in implementation to the

standard receiver channels in terms of the mixers, ADCs, and

filtering blocks. The main difference is that these receivers

operate with an observation bandwidth up to 450 MHz,

allowing the receivers to receive all the transmitter channel

information needed for implementing digital correction

algorithms.

The ADRV9029 transmitter section consists of four identical

and independently controlled channels that provide all the

digital processing, mixed-signal, and RF blocks necessary to

implement a direct conversion system while sharing a common

frequency synthesizer. The digital data from the SERDES lanes

pass through a digital processing block that includes a series of

programmable half-band filters, interpolation stages, and FIR

filters, including a programmable FIR filter with variable

interpolation rates and up to 80 taps. The output of this digital

chain is connected to the digital-to-analog converter (DAC).

The DAC sample rate is adjustable up to 2.5 GHz. The in-phase

(I) and quadrature (Q) channels are identical in each transmitter

signal chain.

Each input is used as the feedback monitor channel for a

corresponding transmitter channel. Table 14 shows the possible

combinations of transmitter and observation channels.

Table 14. Possible Transmitter-Observation Channel

Combinations

Transmitter Channel

Observation Channel

ORX1 or ORX2

ORX3 or ORX4

After conversion to baseband analog signals, the I and Q signals are

filtered to remove sampling artifacts and fed to the upconversion

mixers. Each transmit chain provides a wide attenuation

adjustment range with fine granularity to help designers

optimize signal-to-noise ratio (SNR).

TX1

TX2

TX3

TX4

RECEIVER

CLOCK INPUT

The ADRV9029 provides four independent receiver channels.

Each channel contains all the blocks necessary to receive RF

signals and convert these signals to digital data usable by a

baseband processor. Each receiver can be configured as a direct

conversion system that supports up to a bandwidth of 200 MHz.

Each channel contains a programmable attenuator stage, followed

by matched I and Q mixers that downconvert received signals to

baseband for digitization.

The ADRV9029 requires a differential clock connected to the

DEVCLK pins. The frequency of the clock input must be

between 15 MHz and 1000 MHz and must have low phase

noise because this signal generates the RF LO and internal

sampling clocks.

Rev. 0 | Page 127 of 133

ADRV9029

Data Sheet

eight bits are read from the ADRV9029, either on the SPI_DO

pin in 4-wire mode or on the SPI_DIO pin in 3-wire mode.

SYNTHESIZERS

The ADRV9029 contains four fractional-N PLLs to generate

the RF LO for the signal paths and all internal clock sources.

This group of PLLs includes two RF PLLs for transmit and

receive LO generation, an auxiliary PLL that can be used by the

observation receivers, and a clock PLL. Each PLL is

independently controlled with no need for external

components to set frequencies.

GPIO_X PINS

The ADRV9029 provides 19 general-purpose input/output

signals (GPIOs) referenced to VIF that can be configured for

numerous functions. When configured as outputs, certain pins

can provide real-time signal information to the baseband

processor, allowing the baseband processor to determine

receiver performance. A pointer register selects what

information is output to these pins.

RF Synthesizers

The two RF synthesizers use fractional-N PLLs to generate RF LOs

for multiple receiver and transmitter channels. The fractional-

N PLL incorporates a four-core internal voltage controlled

oscillator (VCO) and loop filter, capable of generating low

phase noise signals with no external components required. An

internal LO multiplexer (mux) enables each PLL to supply LOs

to any or all receivers and transmitters (for example, LO1 to all

transmitters, LO2 to all receivers), resulting in maximum

flexibility when configuring the device for TDD operation. The

LOs on multiple devices can be phase synchronized to support

active antenna systems and beam forming applications.

Signals used for manual gain mode, calibration flags, state

machine status, and various receiver parameters are among

the outputs that can be monitored on the GPIO pins.

Additionally, certain GPIO pins can be configured as inputs and

used for various functions, such as setting the receiver gain in

real time.

AUXILIARY CONVERTERS

GPIO_ANA_x/AUXDAC_x

The ADRV9029 contains eight analog GPIOs (the GPIO_ANA_x

pins) that are multiplexed with eight identical auxiliary DACs

(AUXDAC_x). The analog GPIO ports can be used to control

other analog devices or receive control inputs referenced to the

VDDA_1P8 supply. The auxiliary DACs are 12-bit converters

capable of supplying up to 10 mA. These outputs are typically

used to supply bias current or variable control voltages for

other related components with analog control inputs.

Auxiliary Synthesizer

The auxiliary synthesizer uses a single core VCO fractional-N

PLL to generate the signals necessary to calibrate the device.

The output of this block uses a separate mux system to route

LOs for calibrating different functions during initialization.

The auxiliary synthesizer can also be used to generate LO

signals for the observation receivers or as an offset LO used in

the receiver signal chains.

AUXADC_x

The ADRV9029 contains two auxiliary ADCs with four total

input pins (AUXADC_x). These auxiliary ADCs provide 10-bit

monotonic outputs with an input voltage range of 0.05 V to

0.95 V. When enabled, each auxiliary ADC is free running. An

application programming interface (API) command latches the

ADC output value to a register. The ADRV9029 also contains

an ADC that supports a built-in diode-based temperature sensor.

Clock Synthesizer

The ADRV9029 contains a single core VCO fractional-N PLL

synthesizer that generates all baseband related clock signals and

SERDES clocks. This fractional-N PLL is programmed based on

the data rate and sample rate requirements of the system, which

typically require the system to operate in integer mode.

For JESD204B configurations with Np = 12 and JESD204C

configurations, a dedicated PLL included in the SERDES block

generates the SERDES clocks.

DIGITAL PREDISTORTION (DPD)

The ADRV9029 provides a fully integrated DPD system that

linearizes the output of the transmitter power amplifier by

altering the digital waveform to compensate for nonlinearities

in the power amplifier response. Both the DPD actuator and

coefficient calculation engine are integrated within the device.

This system uses an ORx channel to monitor the output of the

power amplifier and calculates the appropriate predistortion

that must be inserted into the transmitter datapath to linearize

the output. The integrated DPD capability allows the system to

drive the power amplifier closer to saturation, enabling a higher

efficiency power amplifier while maintaining linearity. The DPD is

optimized for power amplifiers with rms output powers in the

250 mW to 10 W range. The DPD engine is highly configurable

and can operate over a range of clock rates, which allows the

DPD system to scale so this system can support different carrier

configurations within the transmitter bandwidth. The additional

SPI INTERFACE

The ADRV9029 uses a SPI to communicate with the baseband

processor. This interface can be configured as a 4-wire interface

with dedicated receive and transmit ports, or the interface can

be configured as a 3-wire interface with a bidirectional data

communications port. This bus allows the baseband processor

to set all device control parameters using a simple address data

serial bus protocol.

Write commands follow a 24-bit format. The first bit sets the

bus direction of the bus transfer. The next 15 bits set the

address where data is written. The final eight bits are the data

being transferred to the specific register address.

Read commands follow a similar format with the exception that

the first 16 bits are transferred on the SPI_DIO pin, and the final

Rev. 0 | Page 128 of 133

Data Sheet

ADRV9029

0

–10

–20

–30

–40

–50

–60

–70

power consumed by the DPD block when enabled ranges from

20 mW per channel (minimum bandwidth) to 325 mW per

channel (maximum bandwidth).

NO DPD

DPD

DPD Improvement Example: 2600 MHz

DPD performance enhancement is shown in Figure 598 for a

20 MHz LTE signal and in Figure 599 for a 100 MHz 5G NR

signal. A Band 41 Skyworks SKY66398-11 high efficiency

power amplifier was used for both the 20 MHz LTE signal and

the 100 MHz 5G NR signal to demonstrate the adjacent

channel level reduction (ACLR) improvement for a particular

device.

Table 15 and Table 16 show the details of the ACLR

improvement achieved for these two scenarios when DPD is

activated. Note that the magnitude of improvement in ACLR is

heavily dependent on the power amplifier used and generally

degrades as signal bandwidth increases.

2350 2400 2450 2500 2550 2600 2650 2700 2750 2800 2850

FREQUENCY (MHz)

Figure 599. Transmitter Output Spectrum for Normal Operation (Red) and

with DPD Activated (Blue) for a 100 MHz, 5G NR100 Waveform, 28 dBm,

LO = 2600 MHz, and R_BW= 100 kHz

DPD Improvement Example: 3500 MHz

20

NO DPD

Performance enhancement is shown in Figure 600 for a 20 MHz

LTE signal, in Figure 601 for a 100 MHz 5G NR signal, and

in Figure 602 for a 2×, 100 MHz 5G NR signal. An NXP

AFSC5G35D37 high efficiency power amplifier was used for

the 20 MHz LTE signal, the 100 MHz 5G NR signal, and the 2×,

100 MHz 5G NR signal to demonstrate the ACLR improvement

for a particular device.

DPD

10

0

–10

–20

–30

–40

–50

Table 15, Table 16, and Table 17 show the details of ACLR

improvement achieved for these two scenarios when DPD is

activated. Note that the magnitude of improvement in ACLR is

heavily dependent on the power amplifier used and generally

degrades as signal bandwidth increases.

–60

10

3450 3460 3470 3480 3490 3500 3510 3520 3530 3540 3550

NO DPD

DPD

FREQUENCY (MHz)

0

Figure 600. Transmitter Output Spectrum for Normal Operation (Red) and

with DPD Activated (Blue) for a 20 MHz LTE Signal, 37 dBm, LO = 3500 MHz,

and R_BW= 100 kHz

–10

–20

–30

–40

–50

–60

20

NO DPD

DPD

10

0

–10

–20

–30

–40

–50

–70

2550 2560 2570 2580 2590 2600 2610 2620 2630 2640 2650

FREQUENCY (MHz)

Figure 598. Transmitter Output Spectrum for Normal Operation (Red) and

with DPD Activated (Blue) for a 20 MHz LTE Signal, 28 dBm, LO = 2600 MHz,

and Resolution Bandwidth (R_BW) = 100 kHz

–60

3250 3000 3350 3400 3450 3500 3550 3600 3650 3700 3750

FREQUENCY (MHz)

Figure 601. Transmitter Output Spectrum for Normal Operation (Red) and

with DPD Activated (Blue) for a 100 MHz, 5G NR100 Waveform, 37 dBm,

LO = 3500 MHz, and R_BW= 100 kHz

Rev. 0 | Page 129 of 133

ADRV9029

Data Sheet

20

NO DPD

DPD

10

0

–10

–20

–30

–40

–50

–60

3200 3250 3300 3350 3400 3450 3500 3550 3600 3650 3700 3750 3800

FREQUENCY (MHz)

Figure 602. Transmitter Output Spectrum for Normal Operation (Red) and

with DPD Activated (Blue) for a 2×, 100 MHz, 5G NR200 Waveform, 37 dBm,

LO = 3500 MHz, and R_BW= 100 kHz

Table 15. 20 MHz LTE Waveform ACLR Comparison With and Without DPD

20 MHz Offset (dBc)

40 MHz Offset (dBc)

Mode¹

Lower

Upper

Lower

Upper

2600 MHz

Normal Operation

DPD Activated

3500 MHz

−38.6

−60.3

−43.5

−60.5

−54.4

−63.2

−58.0

−64.3

Normal Operation

DPD Activated

−31.9

−60.7

−31.0

−59.8

−45.9

−62.6

−45.5

−62.0

¹Waveform is LTE evolved universal terrestrial radio access (E-UTRA) Test Model 3.1 (E-TM 3.1) at 8 dB PAR, with CFR active, 18.015 MHz occupied bandwidth, 28 dBm

output at LO = 2600 MHz, and 37 dBm output at LO = 3500 MHz.

Table 16. 100 MHz 5G NR Waveform ACLR Comparison With and Without DPD

100 MHz Offset (dBc)

200 MHz Offset (dBc)

Upper

Mode¹

Lower

Upper

Lower

2600 MHz

Normal Operation

DPD Activated

3500 MHz

−31.9

−49.5

−42.0

−51.0

−46.5

−52.4

−52.8

−54.5

Normal Operation

DPD Activated

−30.8

−50.9

−28.3

−50.7

−43.9

−52.8

−43.5

−53.1

¹Waveform is NR-FR1-TM3.1 64 QAM (mu = 1:30 kHz subcarrier spacing) at 8 dB PAR with CFR active, 98.28 MHz occupied bandwidth, 28 dBm output at LO = 2600 MHz,

and 37 dBm output at LO = 3500 MHz.

Table 17. 2 × 100 MHz 5G NR Waveform ACLR Comparison With and Without DPD

200 MHz Offset (dBc)

Mode¹

Lower

Upper

3500 MHz

Normal Operation

DPD Activated

−27.5

−49.0

−25.3

−48.3

¹Waveform is two adjacent NR-FR1-TM3.1 64 QAM (mu = 1:30 kHz subcarrier spacing) at 8 dB PAR with CFR active, 196.56 MHz occupied bandwidth, and 37 dBm

output.

Rev. 0 | Page 130 of 133

Data Sheet

ADRV9029

Table 18. Dual Function Boundary Scan Test Pins

Mnemonic JTAG Mnemonic Description

CREST FACTOR REDUCTION (CFR)

The ADRV9029 includes a low power CFR feature that enables

power amplifiers to operate more efficiently. When nonconstant

envelope modulation schemes are used, the signal can have a high

PAR. The CFR algorithm reduces the PAR, enabling the power

amplifier to operate more efficiently while minimizing the impact

to signal quality parameters such as EVM and out of band

emission levels. System designers can configure the CFR algorithm

to ensure these performance parameters are within the system

specification limits.

GPIO_14

GPIO_15

GPIO_16

GPIO_17

GPIO_18

TRST

TDO

TDI

TMS

TCK

Test access port reset

Test data output

Test data input

Test access port mode select

Test clock

Table 19. JTAG Modes

Test Pin Level

GPIO_2 to GPIO_0

XXX¹

000

Description

0

1

Normal operation

JTAG BOUNDARY SCAN

JTAG mode with

differential JESD204B

sync signals

The ADRV9029 provides support for a JTAG boundary scan.

There are five dual function pins associated with the JTAG

interface. These pins, listed in Table 18, are used to access the

on-chip test access port. To enable the JTAG functionality, set

the GPIO_0 pin through the GPIO_2 pin according to Table 19,

depending on how the desired JESD204B sync signals are

configured in the software (differential or single-ended mode).

Pull the TEST_EN pin high to the VIF supply to enable the JTAG

mode.

1

011

JTAG mode with single-

ended JESD204B sync

signals

¹X means any combination.

Rev. 0 | Page 131 of 133

ADRV9029

Data Sheet

APPLICATIONS INFORMATION

If a power-down sequence is followed, to avoid any back

POWER SUPPLY SEQUENCE

biasing of the digital control lines, remove the VDIG_1P0

supply last. If no sequencing is used, it is recommended to

power down all supplies simultaneously.

The ADRV9029 requires a specific power-up sequence to avoid

undesired power-up currents. In the optimal power-up sequence,

the VDIG_1P0 supply is activated first. When VDIG_1P0

powers VDDA_1P0, then all 1.0 V supplies can be powered on

at the same time.

DATA INTERFACE

The digital data interface for the ADRV9029 implements

JEDEC Standard JESD204B Subclass 1 and JESD204C. The

serial interface operates at speeds of up to 24,330.24 Mbps. Table

20, Table 21, and Table 22 list example parameters for various

JESD interface settings. Other output rates, bandwidth, and

number of lanes are also supported for each of the interface

rates reported in Table 20, Table 21, and Table 22.

If VDIG_1P0 is isolated, all VDDA_1P8, VDDA_1P3, and

VDDA_1P0 supplies must be powered up after VDIG_1P0 is

activated. The VIF supply can be powered up at any time.

It is also recommended prior to configuration to toggle the

RESET

signal after power has stabilized.

Table 20. Example Receiver Interface Rates with Four Channels Active (M = 8)

Output

Rate

(MSPS)

JESD204B

Lane Rate

F Parameter (Mbps)

JESD204B

Number of

Lanes

JESD204C

Lane Rate

F Parameter (Mbps)

JESD204C

Number of

Lanes

Bandwidth

(MHz)

JESD Np

Parameter

JESD204B

JESD204C

40

60

61.44

76.8

16

12

16

8

4

9830.4

12288

9830.4

7372.8

9830.4

7372.8

14745.6

1

2

4

2

16

8

4

8110.08

10137.6

8110.08

12165.12

8110.08

12165.12

24330.24

1

2

4

2

1

100

150

200

122.88

184.32

245.76

3

6

12

Table 21. Transmitter Interface Rates with Four Channels Active (M = 8)

Primary

Signal

Bandwidth Bandwidth Rate

Total

Input

JESD204B JESD204B

Lane Rate Number

JESD204C JESD204C

Lane Rate Number

JESD Np

JESD204B

JESD204C

(MHz)

(MSPS) Parameter F Parameter (Mbps)

of Lanes

F Parameter (Mbps)

of Lanes

50

75

100

200

113

150

225

122.88

184.32

245.76

491.52

16

12

8

4

3

9830.4

7372.8

9830.4

7372.8

14745.6

2

4

8

4

6

8

8110.08

12165.12

8110.08

12165.12

24330.24

2

4

2

450

Table 22. Observation Path Interface Rates with 1 Channel Active (M = 2)

Total

Bandwidth

(MHz)

Output

Rate

(MSPS)

JESD204B

Lane Rate

F Parameter (Mbps)

JESD204B

Number of

Lanes

JESD204C

Lane Rate

F Parameter (Mbps)

JESD204C

Number of

Lanes

JESD Np

Parameter

JESD204B

JESD204C

150

225

250

300

450

184.32

245.76

307.2

368.64

491.52

16

12

16

12

4

3

4

2

3

7372.8

9830.4

7372.8

12288

7372.8

9830.4

14745.6

1

2

1

4

3

4

2

4

6082.56

8110.08

6082.56

10137.6

12165.12

8110.08

12165.12

1

2

1

Rev. 0 | Page 132 of 133

Data Sheet

ADRV9029

OUTLINE DIMENSIONS

14.10

14.00 SQ

13.90

A1 BALL

CORNER

A1 BALL

CORNER

8.87 REF

16 14 12 10

17 15 13 11

8

6

4

2

9

7

5

3

1

Solder Mask

Dam

A

C

E

B

D

F

BALL A1

INDICATOR

G

12.80 REF

SQ

H

8.708 REF

J

K

M

P

T

L

0.80

BSC

N

R

U

TOP VIEW

11.07 SQ

0.675

0.600

0.525

BOTTOM VIEW

DETAIL A

1.43

1.34

1.25

1.07

1.00

0.93

DETAIL A

0.39

0.34

0.29

0.60 BSC

SEATING

PLANE

0.50

0.45

0.40

COPLANARITY

0.12

BALL DIAMETER

COMPLIANT TO JEDEC STANDARDS MO-275-JJAB-1

Figure 603. 289-Ball Chip Scale Package Ball Grid Array [CSP_BGA]

(BC-289-6)

Dimensions shown in millimeters

ORDERING GUIDE

Model^{1, 2}

Temperature Range³Package Description

Package Option

BC-289-6

ADRV9029BBCZ

ADRV9029BBCZ-REEL

ADRV9029-HB/PCBZ

ADRV9029-MB/PCBZ

ADRV9029-LB/PCBZ

ADS9-V2EBZ

−40°C to +110°C

289-Ball Chip Scale Package Ball Grid Array [CSP_BGA]

High Band Evaluation Board for 2.8 GHz to 6 GHz

Mid Band Evaluation Board for 650 MHz to 2.8 GHz

Low Band Evaluation Board for 50 MHz to 1.0 GHz

ADS9-V2 Motherboard

¹Z = RoHS Compliant Part.

²The ADS9-V2EBZ motherboard (ordered separately) must be used with the ADRV9029-HB/PCBZ, ADRV9029-MB/PCBZ, or ADRV9020-LB/PCBZ evaluation board.

³See the Junction Temperature section.

registered trademarks are the property of their respective owners.

D25607-12/20(0)

Rev. 0 | Page 133 of 133


型号：	ADRV9029BBCZ
厂家：	ADI
描述：	Integrated, Quad RF Transceiver with Observation Path
文件：	总133页 (文件大小：2761K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

ADRV9029BBCZ [ADI]

相关型号：

ADRV9029BBCZ-REEL

ADRZ01ARZ

ADRZ02ARZ

ADRZ02BRZ

ADRZ03ARZ

ADRZ03BRZ

ADRZ293ERZ

ADRZ421ARZ

ADRZ421BRZ

ADRZ423ARZ

ADRZ423BRZ

ADRZ431ARZ