ADUC814ARU [ADI]
MicroConverter, Small Package 12-Bit ADC with Embedded Flash MCU; 微转换器,小型封装的12位ADC,带有嵌入式闪存微控制器型号: | ADUC814ARU |
厂家: | ADI |
描述: | MicroConverter, Small Package 12-Bit ADC with Embedded Flash MCU |
文件: | 总72页 (文件大小:834K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MicroConverter®, Small Package
12-Bit ADC with Embedded Flash MCU
ADuC814
FUNCTIONAL BLOCK DIAGRAM
FEATURES
ANALOG I/O
ADuC814
6-channel 247 kSPS ADC
12-bit resolution
AIN0
DAC0
DAC1
DAC0
DAC1
BUF
BUF
ADC
CONTROL
LOGIC
DAC
CONTROL
LOGIC
12-BIT
ADC
AIN
MUX
T/H
AIN5
ADC high speed data capture mode
Programmable reference via on-chip DAC for low
level inputs, ADC performance specified to VREF = 1 V
Dual voltage output DACs
12-bit resolution, 15 µs settling time
Memory
8 kbytes on-chip Flash/EE program memory
640 bytes on-chip Flash/EE data memory
Flash/EE, 100 year retention, 100 kcycle endurance
3 levels of Flash/EE program memory security
In-circuit serial downlaod (no external hardware)
256 bytes on-chip data RAM
TEMP
MONITOR
8051-BASED MCU WITH ADDITIONAL
PERIPHERALS
POWER-
ON
RESET
INTERNAL
BAND GAP
V
8 KBYTES FLASH/EE PROGRAM MEMORY
640 BYTES FLASH/EE DATA MEMORY
256 BYTES USER RAM
REF
PROG.
CLOCK
DIVIDER
3 × 16-BIT
TIMER/COUNTERS
1 × WAKE-UP/RTC
TIMER
ON-CHIP MONITORS
POWER SUPPLY
MONITOR
V
BUF
REF
WATCHDOG TIMER
OSC
AND
PLL
C
REF
10 × DIGITAL
UART AND SPI
SERIAL I/O
I/O PINS
XTAL1 XTAL2
Figure 1.
8051 based core
8051 compatible instruction set
32 kHz external crystal,
on-chip programmable PLL (16.78 MHz max)
Three 16-bit timer/counters
11 programmable I/O lines
GENERAL DESCRIPTION
The ADuC814 is a fully integrated 247 kSPS, 12-bit data acquisi-
tion system incorporating a high performance multichannel
ADC, an 8-bit MCU, and program/data Flash/EE memory on a
single chip.
This low power device operates from a 32 kHz crystal with an
on-chip PLL generating a high frequency clock of 16.78 MHz.
This clock is, in turn, routed through a programmable clock
divider from which the MCU core clock operating frequency is
generated.
11 interrupt sources, 2 priority levels
Power
Specified for 3 V and 5 V operation
Normal: 3 mA @ 3 V (core CLK = 2.1 MHz)
Power-down: 15 µA (32 kHz oscillator running)
On-chip peripherals
Power-on reset circuit (no need for external POR device)
Temperature monitor ( 1.5ꢀC accuracy)
Precision voltage reference
The microcontroller core is an 8052 and is compatible with an
8051 instruction. 8 kBytes of nonvolatile Flash/EE program
memory are provided on-chip. 640 bytes of nonvolatile Flash/EE
data memory and 256 bytes RAM are also integrated on-chip.
Time interval counter (wake-up/RTC timer)
UART serial I/O
The ADuC814 also incorporates additional analog functionality
with dual 12-bit DACs, a power supply monitor, and a band gap
reference. On-chip digital peripherals include a watchdog timer,
time interval counter, three timer/counters, and two serial I/O
ports (SPI and UART).
SPI®/I2C® compatible serial I/O
Watchdog timer (WDT), power supply monitor (PSM)
Package and temperature range
28-lead TSSOP 4.4 mm × 9.7 mm package
Fully specified for −40ꢀC to +125ꢀC operation
On-chip factory firmware supports in-circuit serial download
and debug modes (via UART), as well as single-pin emulation
mode via the DLOAD pin. The ADuC814 is supported by a
QuickStart™ Development System.
APPLICATIONS
Optical networking—laser power control
Base station systems—power amplifier bias control
Precision instruments, smart sensors
The part operates from a single 3 V or 5 V supply over the
extended temperature range −40°C to +125°C. When operating
from 3 V supplies, the power dissipation for the part is below
10 mW. The ADuC814 is housed in a 28-lead TSSOP package.
Battery-powered systems, precision system monitors
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.326.8703
www.analog.com
© 2003 Analog Devices, Inc. All rights reserved.
ADuC814
TABLE OF CONTENTS
Specifications..................................................................................... 4
Absolute Maximum Ratings............................................................ 9
ESD Caution.................................................................................. 9
Pin Configuration and Function Description ............................ 10
Terminology .................................................................................... 12
ADC Specifications .................................................................... 12
DAC Specifications..................................................................... 12
Typical Performance Curves......................................................... 13
ADuC814 Architecture, Main Features ....................................... 16
Memory Organization ............................................................... 17
Overview of MCU-Related SFRs.............................................. 18
Accumulator SFR ................................................................... 18
B SFR........................................................................................ 18
Stack Pointer SFR ................................................................... 18
Data Pointer ............................................................................ 18
Program Status Word SFR..................................................... 18
Power Control SFR................................................................. 19
Special Function Registers ........................................................ 20
ADC Circuit Information.............................................................. 21
General Overview....................................................................... 21
ADC Transfer Function............................................................. 21
ADC Data Output Format .................................................... 21
SFR Interface to ADC Block ..................................................... 22
ADCCON1 (ADC Control SFR 1) .......................................... 22
ADCCON2 (ADC Control SFR 2) .......................................... 23
ADCCON3 (ADC Control SFR 3) .......................................... 24
Driving the ADC............................................................................. 25
Voltage Reference Connections................................................ 26
Configuring the ADC ................................................................ 26
Initiating ADC Conversions ..................................................... 27
ADC High Speed Data Capture Mode .................................... 27
ADC Offset and Gain Calibration Overview ......................... 28
ADC Offset and Gain Calibration Coefficients..................... 28
Calibrating the ADC.................................................................. 29
Initiating Calibration in Code .................................................. 29
Nonvolitile Flash/EE Memory...................................................... 30
Flash/EE Memory Overview .................................................... 30
Flash/EE Memory and the ADuC814...................................... 30
ADuC814 Flash/EE Memory Reliability................................. 30
Using Flash/EE Program Memory........................................... 31
Serial Downloading (In-Circuit Programming)................ 31
Parallel Programming............................................................ 31
Flash/EE Program Memory Security....................................... 31
Lock Mode .............................................................................. 31
Secure Mode ........................................................................... 31
Serial Safe Mode..................................................................... 31
Using Flash/EE Data Memory.................................................. 32
ECON—Flash/EE Memory Control SFR ........................... 32
Flash/EE Memory Timing ........................................................ 33
Using the Flash/EE Memory Interface................................ 33
Programming a Byte.............................................................. 33
User Interface to Other On-Chip ADuC814 Peripherals.......... 34
DACs............................................................................................ 34
Using the DACs...................................................................... 35
On-Chip PLL .............................................................................. 37
Time Interval Counter (TIC).................................................... 38
Watchdog Timer......................................................................... 41
Power Supply Monitor............................................................... 42
ADuC814 Configuration Register (CFG814) ........................ 43
Serial Peripheral Interface..................................................... 43
External Clock ........................................................................ 43
Rev. A | Page 2 of 72
ADuC814
Serial Peripheral Interface..........................................................44
MISO (Master In, Slave Out Data I/O Pin).........................44
MOSI (Master Out, Slave In Pin)..........................................44
SCLOCK (Serial Clock I/O Pin)...........................................44
SBUF.........................................................................................53
Mode 0: 8-Bit Shift Register Mode .......................................54
Mode 1: 8-Bit UART, Variable Baud Rate ............................54
Mode 2: 9-Bit UART with Fixed Baud Rate ........................55
Mode 3: 9-Bit UART with Variable Baud Rate....................55
UART Serial Port Baud Rate Generation ............................55
Timer 2 Generated Baud Rates .............................................56
Interrupt System..........................................................................57
Interrupt Priority ....................................................................59
Interrupt Vectors.....................................................................59
ADuC814 Hardware Design Considerations..............................60
Clock Oscillator...........................................................................60
Power Supplies.............................................................................60
Power Consumption...................................................................60
Power-Saving Modes..............................................................61
Power-On Reset ......................................................................61
Grounding and Board Layout Recommendations.............61
Other Hardware Considerations...............................................62
In-Circuit Serial Download Access ......................................62
Embedded Serial Port Debugger ..........................................62
Single-Pin Emulation Mode..................................................63
Timing Specifications .....................................................................64
Outline Dimensions........................................................................70
Ordering Guide ...........................................................................71
SS
(Slave Select Input Pin) .....................................................44
Using the SPI Interface...........................................................45
SPI Interface—Master Mode .................................................45
SPI Interface—Slave Mode ....................................................45
I2C Compatible Interface............................................................46
8051 Compatible On-Chip Peripherals....................................47
Parallel I/O Ports 1 and 3.......................................................47
Additional Digital Outputs Pins ...........................................47
Timers/Counters .........................................................................48
Timer/Counter 0 and 1 Data Registers................................49
Timer/Counter 0 and 1 Operating Modes...............................50
Mode 0 (13-Bit Timer/Counter)...........................................50
Mode 1 (16-Bit Timer/Counter)...........................................50
Mode 2 (8-Bit Timer/Counter with Autoreload)................50
Mode 3 (Two 8-Bit Timer/Counters)...................................50
Timer/Counter 2 Data Registers...........................................51
Timer/Counter 2 Operating Modes .........................................52
16-Bit Autoreload Mode.........................................................52
16-Bit Capture Mode..............................................................52
UART Serial Interface.................................................................53
REVISION HISTORY
12/03 – Data Sheet Changed from REV. 0 to REV. A
Added detailed description of product ........................... Universal
Changes to Specifications.................................................................4
Updated Outline Dimensions........................................................70
Changes to Ordering Guide...........................................................71
Rev. A | Page 3 of 72
ADuC814
SPECIFICATIONS
Table 1. AVDD = DVDD = 2.7 V to 3.3 V or 4.5 V to 5.5 V, VREF = 2.5 V internal reference, XTAL1/XTAL2 = 32.768 kHz crystal. All
specifications TMIN to TMAX, unless otherwise specified1
Parameter
VDD = 5 V
VDD = 3 V
Unit
Test Conditions
ADC CHANNEL SPECIFICATIONS
A GRADE
DC ACCURACY2,3
Resolution
Integral Nonlinearity
fSAMPLE = 147 kHz
12
2
1
2.5
4
2
12
2
1
2.5
4
2
Bits
LSB max
LSB typ
LSB typ
LSB max
LSB typ
LSB typ
2.5 V internal reference
1.0 V external reference
2.5 V internal reference
Differential Nonlinearity
5
5
1.0 V external reference
CALIBRATED ENDPOINT ERRORS4, 5
Offset Error
Offset Error Match
Gain Error
5
1
5
1
5
1
5
1
LSB max
LSB typ
LSB max
LSB typ
Gain Error Match
DYNAMIC PERFORMANCE6
fIN = 10 kHz sine wave
fSAMPLE = 147 kHz
Signal to Noise Ratio (SNR)7
Total Harmonic Distortion (THD)
Peak Harmonic or Spurious Noise
Channel-to-Channel Crosstalk8
B GRADE
62.5
–65
–65
–80
62.5
–65
–65
–80
dB typ
dB typ
dB typ
dB typ
DC ACCURACY2, 3
fSAMPLE = 147 kHz
Resolution
12
12
Bits
Integral Nonlinearity
1
0.3
1.5
0.9
0.25
+1.5/–0.9
1
1
LSB max
LSB typ
LSB max
LSB max
LSB typ
LSB max
LSB typ
2.5 V internal reference
0.3
1.5
0.9
0.25
1.5/–0.9
1
1.0 V external reference11
2.5 V internal reference
Differential Nonlinearity
1.0 V external reference11
ADC input is a dc voltage
Code Distribution
CALIBRATED ENDPOINT ERRORS4, 5
Offset Error
Offset Error Match
Gain Error
2
1
2
1
3
1
3
1
LSB max
LSB typ
LSB max
LSB typ
Gain Error Match
DYNAMIC PERFORMANCE6
fIN = 10 kHz sine wave
fSAMPLE = 147 kHz
Signal to Noise Ratio (SNR)7
Total Harmonic Distortion (THD)
Peak Harmonic or Spurious Noise
Channel-to-Channel Crosstalk8
ANALOG INPUT
71
71
dB typ
dB typ
dB typ
dB typ
–85
–85
–80
–85
–85
–80
Input Voltage Ranges
0 to VREF
0 to VREF
V
Leakage Current
Input Capacitance
1
32
1
32
µA max
pF typ
Rev. A | Page 4 of 72
ADuC814
Parameter
VDD = 5 V
VDD = 3 V
Unit
Test Conditions
TEMPERATURE MONITOR9
Voltage Output at 25ºC
Voltage TC
650
–2
3
650
–2
3
mV typ
mV/ºC typ
ºC typ
Accuracy
2.5 V internal reference
2.5 V external reference
Accuracy
1.5
1.5
ºC typ
DAC CHANNEL SPECIFICATIONS
DC ACCURACY10
Resolution
Relative Accuracy
Differential Nonlinearity11
DAC Load to AGND RL = 10 kΩ, CL = 100 pF
12
+3
–1
1/2
50
1
12
+3
–1
1/2
50
1
Bits
LSB typ
LSB max
LSB typ
mV max
% max
% typ
Guaranteed montonic
Offset Error
Gain Error
VREF range
VREF range
AVDD range
1
1
Gain Error Mismatch
ANALOG OUTPUTS
Voltage Range_0
Voltage Range_1
Output Impedance
ISINK
0.5
0.5
% typ
Of full scale on DAC1
0 to VREF
0 to VDD
0.5
Volts
Volts
Ω typ
µA typ
DAC VREF = 2.5 V
DAC VREF = VDD
0.5
50
50
DAC AC Specifications
Voltage Output Settling Time
15
10
15
10
µs typ
Full-scale settling time to within ½ LSB of final
value
1 LSB change at major carry
Digital-to-Analog Glitch Energy
REFERENCE INPUT/OUTPUT
REFERENCE OUTPUT
nVs typ
Output Voltage (VREF
Accuracy
Power Supply Rejection
Reference Tempco
Internal VREF Power-On Time12
EXTERNAL REFERENCE INPUT13
)
2.5
2.5
47
100
80
2.5
2.5
57
100
80
V
% max
dB typ
ppm/ºC typ
ms typ
Of VREF measured at the CREF pin
Internal band gap reference deselected via
ADCCON2.6
14
Voltage Range (VREF
)
1.0
VDD
20
1.0
VDD
20
V min
V max
kΩ typ
µA max
Input Impedance
Input Leakage
10
10
POWER SUPPLY MONITOR (PSM)
VDD Trip Point Selection Range
2.63
2.93
3.08
4.63
3.5
2.63
2.93
3.08
V
V
V
V
Four trip points selectable in this range
programmed via TP1–0 in PSMCON
VDD Power Supply Trip Point Accuracy
WATCH DOG TIMER (WDT)14
Timeout Period
3.5
% max
0
2000
0
2000
ms min
ms max
Nine time-out periods selectable in this range
programmed via PRE3–0 in WDCON
LOGIC INPUTS
INPUT VOLTAGES14
All Inputs except SCLOCK, RESET, and
XTAL1
VINL, Input Low Voltage
VINH, Input High Voltage
0.8
2.0
0.4
2.0
V max
V min
Rev. A | Page 5 of 72
ADuC814
Parameter
VDD = 5 V
VDD = 3 V
Unit
Test Conditions
SCLOCK and RESET Only14
(Schmitt-Triggered Inputs)
VT+
1.3
3.0
0.8
1.4
0.3
0.85
0.95
2.5
0.4
1.1
0.3
V min
V max
V min
V max
V min
V max
VT–
VT+ – VT–
0.85
INPUT CURRENTS
P1.2–P1.7, DLOAD
SCLOCK15
10
–10
–40
10
10
20
105
10
1
10
–3
–15
10
10
10
35
10
1
µA max
µA min
µA max
µA max
µA max
µA min
µA max
µA max
µA typ
µA min
µA max
µA typ
µA min
µA max
µA typ
pF typ
VIN = 0 V or VDD
VIN = 0 V, internal pull-up
VIN = 0 V, internal pull-up
VIN = VDD
RESET
VIN = 0 V
VIN = 5 V, 3 V internal pull-down
VIN = 5 V, 3 V internal pull-down
VIN = 5 V, 3 V
P1.0, P1.1, Port 315
SS
(includes MISO, MOSI/SDATA and
)
–180
–660
–360
–20
–75
–38
5
–70
–200
–100
–5
–25
–12
5
VIN = 2 V, VDD = 5 V, 3 V
VIN = 450 mV, VDD = 5 V, 3 V
All digital inputs
INPUT CAPACITANCE
CRYSTAL OSCILLATOR
(XTAL1 AND XTAL2)
Logic Inputs, XTAL1 Only
VINL, Input Low Voltage
VINH, Input High Voltage
XTAL1 Input Capacitance
XTAL2 Output Capacitance
DIGITAL OUTPUTS
0.8
3.5
18
0.4
2.5
18
V typ
V typ
pF typ
pF typ
18
18
Output High Voltage (VOH)
Output Low Voltage (VOL)
Port 1.0 and Port 1.1
Port 1.0 and Port 1.1
SCLOCK, MISO/MOSI
All Other Outputs
2.4
2.4
V min
ISOURCE = 80 mA
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
V max
V max
V max
V max
ISINK = 10 mA, TMAX = 85°C
ISINK = 10 mA, TMAX = 125°C
ISINK = 4 mA
ISINK = 1.6 mA
MCU CORE CLOCK
MCU Clock Rate
131.1
16.78
131.1
16.78
kHz min
Clock rate generated via on-chip PLL,
programmable via CD2-0 in PLLCON
MHz max
START UP TIME
At Power-On
From Idle Mode
500
100
500
100
ms typ
µs typ
From Power-Down Mode
Oscillator Running
OSC_PD = 0 in PLLCON SFR
INT0
100
100
100
3
100
100
100
3
µs typ
µs typ
µs typ
ms typ
Wake-Up with
Interrupt
Wake-Up with SPI/I2C Interrupt
Wake-Up with TIC Interrupt
Wake-Up with External RESET
Rev. A | Page 6 of 72
ADuC814
Parameter
Oscillator Powered Down16
INT0
Wake-Up with SPI/I2C Interrupt
Wake-Up with External RESET
After External RESET in Normal Mode
After WDT Reset in Normal Mode
VDD = 5 V
VDD = 3 V
Unit
Test Conditions
OSC_PD = 1 in PLLCON SFR
150
150
150
3
400
400
400
3
ms typ
ms typ
ms typ
ms typ
ms typ
Wake-Up with
Interrupt
3
3
Controlled via WDCON SFR
FLASH/EE MEMORY RELIABILITY
CHARACTERISTICS17
Endurance18
Data Retention19
100,000
100
100,000
100
Cycles min
Years min
POWER REQUIREMENTS20, 21
Power Supply Voltages
AVDD/DVDD – AGND
2.7
3.3
V min
V max
V min
V max
AVDD/DVDD = 3 V nom
AVDD/DVDD = 5 V nom
4.5
5.5
Power Supply Currents, Normal Mode
DVDD Current14
5
4
2.5
2
1.7
10
8
1.7
1.5
1.2
1.7
mA max
mA typ
mA max
mA max
mA typ
mA max
mA max
mA typ
mA max
Core CLK = 2.097 MHz
(CD bits in PLLCON = 3)
AVDD Current14
DVDD Current
1.7
20
16
1.7
3.5
2.8
1.7
Core CLK = 16.78MHz (max)
(CD bits in PLLCON = 0)
AVDD Current
DVDD Current14
Core CLK = 131.2 kHz (min)
(CD bits in PLLCON = 7)
AVDD Current
Power Supply Currents, Idle Mode
DVDD Current14
1.7
1.5
0.15
6
1.2
1
0.15
3
2.5
0.15
1
0.7
0.15
mA max
mA typ
mA max
mA max
mA typ
mA max
mA max
mA typ
mA max
Core CLK = 2.097 MHz
(CD Bits in PLLCON = 3)
AVDD Current14
DVDD Current14
Core CLK = 16.78 MHz (max)
(CD bits in PLLCON = 0)
4
AVDD Current14
DVDD Current14
0.15
1.25
1.1
0.15
Core CLK = 131 kHz (min)
(CD bits in PLLCON = 7)
AVDD Current14
Power Supply Currents, Power-Down
Mode
Core CLK = 2.097 MHz or 16.78 MHz (CD bits in
PLLCON = 3 or 0)
Oscillator on
DVDD Current14
20
14
1
15
10
1
µA max
µA typ
µA typ
µA max
µA typ
µA typ
40
1
AVDD Current
DVDD Current
Oscillator off
20
1
AVDD Current
Typical Additional Power Supply
Currents
Core CLK = 2.097 MHz, (CD bits in PLLCON = 3)
AVDD = DVDD = 5 V
PSM Peripheral
ADC
DAC
50
1.5
150
µA typ
mA typ
µA typ
Rev. A | Page 7 of 72
ADuC814
1Temperature range –40ºC to +125ºC.
2ADC linearity is guaranteed when operating in nonpipelined mode, i.e., ADC conversion followed sequentially by a read of the ADC result. ADC linearity is also
guaranteed during normal MicroConverter core operation.
3ADC LSB size = VREF /212, i.e., for internal VREF = 2.5 V, 1 LSB = 610 µV, and for external VREF = 1 V, 1 LSB = 244 µV.
4Offset and gain error and offset and gain error match are measured after factory calibration.
5Based on external ADC system components the user may need to execute a system calibration to remove additional external channel errors
and achieve these specifications.
6Measured with coherent sampling system using external 16.77 MHz clock via P3.5 (Pin 22).
7SNR calculation includes distortion and noise components.
8Channel-to-channel crosstalk is measured on adjacent channels.
9The temperature monitor gives a measure of the die temperature directly; air temperature can be inferred from this result.
10DAC linearity is calculated using a reduced code range of 48 to 4095, 0 V to VREF range; a reduced code range of 48 to 3950, 0 V to VDD range. DAC output load = 10 kΩ
and 100 pF.
11DAC differential nonlinearity specified on 0 V to VREF and 0 to VDD ranges.
12Measured with VREF and CREF pins decoupled with 0.1 µF capacitors to ground. Power-up time for the internal reference is determined by the value of the decoupling
capacitor chosen for both the VREF and CREF pins.
13When using an external reference device, the internal band gap reference input can be bypassed by setting the ADCCON1.6 bit. In this mode, the VREF and CREF pins
need to be shorted together for correct operation.
14These numbers are not production tested but are guaranteed by design and/or characterization data on production release.
15Pins configured in I2C compatible mode or SPI mode; pins configured as digital inputs during this test.
16These typical specifications assume no loading on the XTAL2 pin. Any additional loading on the XTAL2 pin increases the power-on times.
17Flash/EE memory reliability characteristics apply to both the Flash/EE program memory and the Flash/EE data memory.
18Endurance is qualified to 100 kcycles as per JEDEC Std. 22, Method A117 and measured at –40ºC, +25°C, and +125°C; typical endurance at +25°C is 700 kcycles.
19Retention lifetime equivalent at junction temperature (TJ) = 55°C as per JEDEC Std. 22, Method A117. Retention lifetime based on an activation energy of 0.6 eV
derates with junction temperature as shown in Figure 33 in the Flash/EE memory description section.
20Power supply current consumption is measured in normal, idle, and power-down modes under the following conditions:
Normal Mode: Reset and all digital I/O pins = open circuit, core Clk changed via CD bits in PLLCON, core executing internal software loop.
Idle Mode: Reset and all digital I/O pins = open circuit, core Clk changed via CD bits in PLLCON, PCON.0 = 1, core execution suspended in idle mode.
Power-Down Mode: Reset and all P1.2–P1.7 pins = 0.4 V; all other digital I/O pins are open circuit, Core Clk changed via CD bits in PLLCON, PCON.1 = 1,
Core execution suspended in power-down mode, OSC turned on or off via OSC_PD bit (PLLCON.7) in PLLCON SFR.
21DVDD power supply current increases typically by 3 mA (3 V operation) and 10 mA (5 V operation) during a Flash/EE memory program or erase cycle.
Rev. A | Page 8 of 72
ADuC814
ABSOLUTE MAXIMUM RATINGS
Table 2. Temperature = 25°C, unless otherwise noted
Parameter
Rating
AVDD to AGND
DVDD to AGND
AVDD to DVDD
AGND to DGND1
–0.3 V to +7 V
–0.3 V to +7 V
–0.3 V to +0.3 V
–0.3 V to +0.3 V
–0.3 V to AVDD + 0.3 V
–0.3 V to AVDD + 0.3 V
30 mA
Analog Input Voltage to AGND2
Reference Input Voltage to AGND
Analog Input Current (Indefinite)
Reference Input Current (Indefinite)
Digital Input Voltage to DGND
Digital Output Voltage to DGND
Operating Temperature Range
Storage Temperature Range
Junction Temperature
θJA Thermal Impedance
Lead Temperature, Soldering
Vapor Phase (60 sec)
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
30 mA
–0.3 V to DVDD + 0.3 V
–0.3 V to DVDD + 0.3 V
−40°C to +125°C
−65°C to +150°C
150°C
97.9°C/W
215°C
220°C
Infrared (15 sec)
1 AGND and DGND are shorted internally on the ADuC814.
2 Applies to Pins P1.2 to P1.7 operating in analog or digital input mode.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. A | Page 9 of 72
ADuC814
PIN CONFIGURATION AND FUNCTION DESCRIPTION
DGND
1
2
3
4
5
6
7
8
9
28 DV
DD
DLOAD
27 XTAL2
P3.0/RxD
26 XTAL1
P3.1/TxD
25 SCLOCK
P3.2/INT0
24 P3.7/SDATA/MOSI
23 P3.6/MISO
P3.3/INT1
ADuC814
P3.4/T0/CONVST
P1.0/T2
22 P3.5/T1/SS/EXTCLK
21 P1.7/ADC5/DAC1
20 P1.6/ADC4/DAC0
19 P1.5/ADC3
TOP VIEW
(Not to Scale)
P1.1/T2EX
RESET 10
P1.2/ADC0 11
P1.3/ADC1 12
18 P1.4/ADC2
17
16
C
REF
REF
AV
13
V
DD
AGND 14
15 AGND
Figure 2. Pin Configuration
Table 3. Pin Descriptions
Pin No. Mnemonic
Type
Function
1
2
DGND
DLOAD
S
I
Digital Ground. Ground reference point for the digital circuitry.
Debug/Serial Download Mode. Enables when pulled high through a resistor on power-on or RESET. In
this mode, DLOAD may also be used as an external emulation I/O pin, therefore the voltage level at
this pin must not be changed during this mode of operation because it may cause an emulation
interrupt that halts code execution. User code is executed when this pin is pulled low on power-on or
RESET.
3–7
P3.0 – P3.4
I/O
Bidirectional Port Pins with Internal Pull-Up Resistors. Port 3 pins that have 1s written to them are
pulled high by the internal pull-up resistors, and in that state they can be used as inputs. As inputs,
with Port 3 pins being pulled low externally, they source current because of the internal pull-up
resistors. When driving a 0-to-1 output transition, a strong pull-up is active during S1 of the
instruction cycle. Port 3 pins also have various secondary functions which are described next.
3
4
5
P3.0/RxD
P3.1/TxD
I/O
I/O
I/O
Receiver Data Input (asynchronous) or Data Input/Output (synchronous) in Serial (UART) Mode.
Transmitter Data Output (asynchronous) or Clock Output (synchronous) in Serial (UART) Mode.
Interrupt 0, programmable edge or level-triggered interrupt input, which can be programmed to one
of two priority levels. This pin can also be used as agate control input to Timer 0.
INT0
P3.2/
6
INT1
I/O
I/O
I/O
Interrupt 1, programmable edge or level-triggered interrupt input, which can be programmed to one
of two priority levels. This pin can also be used as agate control input to Timer 1.
Timer/Counter 0 Input and External Trigger Input for ADC Conversion Start.
P3.3/
7
P3.4/T0/
CONVST
8–9
P1.0–P1.1
Bidirectional Port Pins with Internal Pull-Up Resistors. Port 1 pins that have 1s written to them are
pulled high by the internal pull-up resistors, and in that state they can be used as inputs. As inputs
,with Port 1 pins being pulled low externally, they source current because of the internal pull-up
resistors When driving a 0-to-1 output transition a strong pull-up is active during S1 of the instruction
cycle. Port 1 pins also have various secondary functions which are described as follows.
8
P1.0/T2
I/O
Timer 2 Digital Input. Input to Timer/Counter 2. When enabled, Counter 2 is incremented in response
to a 1 to 0 transition of the T2 input.
9
10
P1.1/T2EX
RESET
I/O
I
Digital Input. Capture/Reload trigger for Counter 2.
Reset Input. A high level on this pin while the oscillator is running resets the device. There is an
internal weak pull-down and a Schmitt-trigger input stage on this pin.
11–12
P1.2–P1.3
I
Port 1.2 to P1.3. These pins have no digital output drivers, i.e., they can only function as digital inputs,
for which 0 must be written to the port bit. These port pins also have the following analog functionality:
11
12
13
P1.2/ADC0
P1.3/ADC1
AVDD
I
I
S
ADC Input Channel 0. Selected via ADCCON2 SFR.
ADC Input Channel 1. Selected via ADCCON2 SFR.
Analog Positive Supply Voltage, 3 V or 5 V.
14–15
16
AGND
VREF
G
I/O
Analog Ground. Ground reference point for the analog circuitry.
Reference Input/Output. This pin is connected to the internal reference through a switch and is the
reference source for the analog to digital converter. The nominal internal reference voltage is 2.5 V
and this appears at the pin. This pin can be used to connect an external reference to the analog to
digital converter by setting ADCCON1.6 to 1. Connect 0.1 µF between this pin and AGND.
Rev. A | Page 10 of 72
ADuC814
Pin No. Mnemonic
Type
Function
17
18–21
CREF
P1.4–P1.7
I
I
Decoupling Input for On-Chip Reference. Connect 0.1 µF between this pin and AGND.
Port 1.4 to P1.7. These pins have no digital output drivers, i.e., they can only function as digital inputs,
for which 0 must be written to the port bit. These port pins also have the following analog functionality:
18
19
20
P1.4/ADC2
P1.5/ADC3
P1.6/ADC4/
DAC0
I
I
ADC Input Channel 2. Selected via ADCCON2 SFR.
ADC Input Channel 2. Selected via ADCCON2 SFR.
ADC Input Channel 4. Selected via ADCCON2 SFR. The voltage DAC Channel 0 can also be configured
to appear on P1.6.
I/O
21
P1.7/
ADC5/DAC1
P3.5–P3.7
I/O
I/O
ADC Input Channel 5, selected via ADCCON2 SFR. The voltage DAC Channel 1 can also be configured
to appear on P1.7.
22–24
Bidirectional Port Pins with Internal Pull-Up Resistors. Port 3 pins that have 1s written to them are
pulled high by the internal pull-up resistors, and in that state they can be used as inputs. As inputs
,with Port 3 pins being pulled low externally, they source current because of the internal pull-up
resistors. When driving a 0-to-1 output transition a strong pull-up is active during S1 of the instruction
cycle. Port 3 pins also have various secondary functions which are described as follows.
22
22
P3.5/T1
I/O Timer/Counter 1 Input. P3.5–P3.7 pins also have SPI interface functions. To enable these functions,
Bit 0 of the CFG814 SFR must be set to 1.
This pin also functions as the Slave Select input for the SPI interface when the device is operated in
slave mode. P3.5 can also function as an input for an external clock. This clock effectively bypasses the
PLL. This function is enabled by setting Bit 1 of the CFG814 SFR.
SS
P3.5/
/EXTCLK
I/O
23
24
P3.6/MISO
P3.7/SDATA/
MOSI
I/O
I/O
SPI Master Input/Slave Output Data Input/Output Pin.
SPI Master Output/Slave Input Data Input/Output Pin.
25
26
27
28
SCLOCK
XTAL1
XTAL2
DVDD
I/O
I
O
S
Serial Clock Pin for SPI Serial Interface Clock.
Input to the Crystal Oscillator Inverter.
Output from the Crystal Oscillator Inverter.
Analog Positive Supply Voltage, 3 V or 5 V.
I = Input, O = Output, S = Supply, G - Ground.
The following notes apply to the entire data sheet:
•
•
•
In bit designation tables, set implies a Logic 1 state, and cleared implies a Logic 0 state, unless otherwise stated.
Set and cleared also imply that the bit is set or cleared by the ADuC814 hardware, unless otherwise stated.
User software should not write to reserved or unimplemented bits as they may be used in future products.
Rev. A | Page 11 of 72
ADuC814
TERMINOLOGY
ADC SPECIFICATIONS
Integral Nonlinearity
DAC SPECIFICATIONS
Relative Accuracy
This is the maximum deviation of any code from a straight line
passing through the endpoints of the ADC transfer function.
The endpoints of the transfer function are zero scale, a
point1/2 LSB below the first code transition and full scale, a
point 1/2 LSB above the last code transition.
Relative accuracy or endpoint linearity is a measure of the
maximum deviation from a straight line passing through the
endpoints of the DAC transfer function. It is measured after
adjusting for zero-scale error and full-scale error.
Voltage Output Settling Time
Differential Nonlinearity
This is the amount of time it takes for the output to settle to a
specified level for a full-scale input change.
This is the difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Digital-to-Analog Glitch Impulse
Offset Error
This is the amount of charge injected into the analog output
when the inputs change state. It is specified as the area of the
glitch in nV-sec.
This is the deviation of the first code transition (0000 … 000) to
(0000 … 001) from the ideal, i.e., +1/2 LSB.
Full-Scale Error
This is the deviation of the last code transition from the ideal
AIN voltage (full-scale error has been adjusted out).
Signal-to-(Noise + Distortion) Ratio
This is the measured ratio of signal-to-(noise + distortion) at
the output of the ADC. The signal is the rms amplitude of the
fundamental. Noise is the rms sum of all nonfundamental
signals up to half the sampling frequency (fS/2), excluding dc.
The ratio is dependent upon the number of quantization levels
in the digitization process; the more levels, the smaller the
quantization noise. The theoretical signal-to-(noise + distortion)
ratio for an ideal N-bit converter with a sine wave input is given
by
Signal-to =- (Noise + Distortion) = (6.02N + 1.76)
Thus, for a 12-bit converter, this is 74 dB.
Total Harmonic Distortion (THD)
Total harmonic distortion is the ratio of the rms sum of the
harmonics to the fundamental.
Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to fS/2 and including dc) to the rms value of the
fundamental. Normally, the value of this specification is
determined by the largest harmonic in the spectrum, but for
ADCs where the harmonics are buried in the noise floor, it is
the noise peak.
Rev. A | Page 12 of 72
ADuC814
TYPICAL PERFORMANCE CURVES
The typical performance plots presented in this section
illustrate typical performance of the ADuC814 under various
operating conditions. Note that all typical plots in this section
were generated using the ADuC814BRU, i.e., the B-grade part.
Figure 5 and Figure 6 show the variation in worst-case positive
(WCP) INL and worst-case negative (WCN) INL versus
external reference input voltage.
1.2
0.6
AV /DV = 5V
DD DD
1.0
fS = 152kHz
Figure 3 and Figure 4 show typical ADC integral nonlinearity
(INL) errors from ADC Code 0 to Code 4095 at 5 V and 3 V
supplies, respectively. The ADC is using its internal reference
(2.5 V) and operating at a sampling rate of 152 kHz. The typical
worst-case errors in both plots are just less than 0.3 LSBs.
0.4
0.8
0.6
0.2
0
WCP INL
0.4
0.2
0.4
AV /DV = 5V
DD DD
fS = 152kHz
0
–0.2
–0.4
0.3
0.2
0.1
WCN INL
–0.2
–0.4
–0.6
–0.6
0.5
1.0
1.5
2.0
2.5
5.0
0
EXTERNAL REFERENCE (V)
–0.1
Figure 5. Typical Worst-Case INL Error vs. VREF, VDD = 5 V
–0.2
0.8
0.6
0.8
–0.3
–0.4
AV /DV = 3V
DD DD
fS = 152kHz
0.6
0
511
1023 1535
2047 2559
3071
3583 4095
0.4
WCP INL
0.4
ADC CODES
0.2
0.2
Figure 3. Typical INL Error, VDD = 5 V
0
0
0.4
0.3
0.2
0.1
–0.2
–0.4
–0.6
–0.8
–0.2
–0.4
–0.6
–0.8
AV /DV = 3V
DD DD
fS = 152kHz
WCN INL
0.5
1.0
1.5
2.0
2.5
3.0
EXTERNAL REFERENCE (V)
0
–0.1
Figure 6. Typical Worst-Case INL Error vs. VREF, VDD = 3 V
–0.2
Figure 7 and Figure 8 show typical ADC differential nonlinearity
(DNL) errors from ADC Code 0 to Code 4095 at 5 V and 3 V
supplies, respectively. The ADC is using its internal reference
(2.5 V) and operating at a sampling rate of 152 kHz. The typical
worst-case errors in both plots are just less than 0.2 LSBs.
–0.3
–0.4
0
511
1023 1535
2047 2559
3071
3583 4095
ADC CODES
Figure 4. Typical INL Error, VDD = 3 V
Rev. A | Page 13 of 72
ADuC814
0.30
0.25
0.20
0.15
0.10
0.05
0
0.7
0.7
0.5
AV /DV = 3V
DD DD
fS = 152kHz
0.5
WCP DNL
0.3
0.3
0.1
0.1
–0.1
–0.3
–0.5
–0.7
–0.1
–0.3
–0.5
–0.7
WCN DNL
–0.50
–0.10
–0.15
–0.20
AV /DV = 5V
DD DD
fS = 152kHz
0.5
1.0
1.5
2.0
2.5
3.0
–0.25
0
511
1023 1535
2047 2559
3071
3583 4095
EXTERNAL REFERENCE (V)
ADC CODES
Figure 10. Typical Worst-Case DNL Error vs. VREF, VDD = 3 V
Figure 7. Typical DNL Error, VDD = 5 V
Figure 11 shows a histogram plot of 10,000 ADC conversion
results on a dc input with VDD = 5 V. The plot illustrates an
excellent code distribution pointing to the low noise
performance of the on-chip precision ADC.
0.30
0.25
0.20
0.15
0.10
0.05
0
AV /DV = 3V
DD DD
fS = 152kHz
10000
8000
6000
4000
2000
0
–0.50
–0.10
–0.15
–0.20
–0.25
0
511
1023 1535
2047 2559
3071
3583 4095
ADC CODES
817
818
819
CODE
820
821
Figure 8. Typical DNL Error, VDD = 3 V
Figure 9 and Figure 10 show the variation in worst-case positive
(WCP) DNL and worst-case negative (WCN) DNL versus
external reference input voltage.
Figure 11. Code Histogram plot, VDD = 5 V
Figure 12 shows a histogram plot of 10,000 ADC conversion
results on a dc input for VDD = 3 V. The plot again illustrates a
very tight code distribution of 1 LSB with the majority of codes
appearing in one output bin.
0.6
0.4
0.2
0.6
AV
fS = 152kHz
/DV
= 5V
DD
DD
0.4
10000
9000
8000
7000
6000
5000
4000
3000
2000
1000
0
WCP DNL
0.2
0
0
–0.2
–0.4
–0.6
–0.2
–0.4
–0.6
WCN DNL
0.5
1.0
1.5
2.0
2.5
5.0
EXTERNAL REFERENCE (V)
Figure 9. Typical Worst-Case DNL Error vs. VREF, VDD = 5 V
817
818
819
820
821
CODE
Figure 12. Code Histogram Plot, VDD = 3 V
Rev. A | Page 14 of 72
ADuC814
Figure 13 and Figure 14 show typical FFT plots for the ADuC814.
These plots were generated using an external clock input via
P3.5 to achieve coherent sampling. The ADC is using its internal
reference (2.5 V) sampling a full-scale, 10 kHz sine wave test
tone input at a sampling rate of 149.79 kHz. The resultant FFTs
shown at 5 V and 3 V supplies illustrate an excellent 100 dB
noise floor, a 71 dB signal-to-noise ratio (SNR), and a THD
greater than −80 dB.
Figure 15 and Figure 16 show typical dynamic performance
versus external reference voltages. Again excellent ac performance
can be observed in both plots with some roll-off being observed
as VREF falls below 1 V.
–70
80
AV /DV = 5V
DD DD
fS = 152kHz
–75
75
SNR
–80
–85
–90
70
20
AV /DV = 5V
DD DD
f
= 149.79kHz
0
–20
S
f
= 9.910kHz
65
60
55
50
IN
THD
SNR = 71.3dB
THD = –88.0dB
ENOB = 11.6
–40
–60
–95
–80
–100
–100
–120
–140
–160
0.5
1.0
1.5
2.0
2.5
5.0
EXTERNAL REFERENCE (V)
Figure 15. Typical Dynamic Performance vs. VREF, VDD = 5 V
0
10
20
30
40
50
60
70
80
75
70
65
60
55
50
–70
–75
–80
–85
–90
–95
–100
FREQUENCY (kHz)
AV /DV = 3V
DD DD
fS = 152kHz
Figure 13. ADuC814 Dynamic Performance at VDD = 5 V
SNR
20
0
AV /DV = 3V
DD DD
f
f
SNR = 71.3dB
THD = –88.0dB
ENOB = 11.6
THD
= 149.79kHz
= 9.910kHz
S
IN
–20
–40
–60
–80
–100
–120
–140
–160
0.5
1.0
1.5
2.0
2.5
3.0
EXTERNAL REFERENCE (V)
Figure 16. Typical Dynamic Performance vs. VREF, VDD = 3 V
0
10
20
30
40
50
60
70
FREQUENCY (kHz)
Figure 14. ADuC814 Dynamic Performance at VDD = 3 V
Rev. A | Page 15 of 72
ADuC814
ADuC814 ARCHITECTURE, MAIN FEATURES
reference. On-chip digital peripherals include a watchdog timer,
time interval counter, three timer/counters, and three serial I/O
ports (SPI, UART, I2C).
The ADuC814 is a fully integrated 247 kSPS 12-bit data
acquisition system incorporating a high performance multi-
channel ADC, an 8-bit MCU, and program/data Flash/EE
memory on a single chip.
On-chip factory firmware supports in-circuit serial download
and debug modes (via UART), as well as single-pin emulation
mode via the DLOAD pin. A detailed functional block diagram
of the ADuC814 is shown in Figure 17.
This low power device operates from a 32 kHz crystal with an
on-chip PLL generating a high frequency clock of 16.78 MHz.
This clock is, in turn, routed through a programmable clock
divider from which the MCU core clock operating frequency is
generated.
The ADuC814 is supported by a QuickStart Development
System. This is a full-featured, low cost system, consisting of
PC-based (Windows compatible) hardware and software
development tools.
The microcontroller core is an 8052, and therefore 8051,
instruction set compatible. The microcontroller core machine
cycle consists of 12 core clock periods of the selected core
operating frequency. Eight kbytes of nonvolatile Flash/EE
program memory are provided on-chip. 640 bytes of nonvolatile
Flash/EE data memory and 256 bytes RAM are also integrated
on-chip.
The part operates from a single 3 V or 5 V supply. When
operating from 3 V supplies, the power dissipation for the part
is below 10 mW. The ADuC814 is housed in a 28-lead TSSOP
package and is specified for operation over an extended
temperature range −40°C to +125°C.
The ADuC814 also incorporates additional analog functionality
with dual 12-bit DACs, a power supply monitor, and a band gap
ADuC814
ADC0 11
DAC0
DAC1
DAC0
DAC1
BUF
BUF
ADC
CONTROL
AND
CAL
LOGIC
DAC
CONTROL
LOGIC
12-BIT
ADC
AIN
MUX
T/H
21
ADC5
TEMP MONITOR
DAC0
DAC1
T0
T1
256 × 8
USER RAM
640 × 8
16-BIT
COUNTER
TIMERS
DATA
V
REF
AGND
FLASH/EE
T2
8052
WATCHDOG
TIMER
BAND GAP
REFERENCE
8k × 8
PROGRAM
FLASH/EE
T2EX
MCU
CORE
POWER SUPPLY
MONITOR
TIME
INTERVAL
COUNTER
INT0
INT1
D0
V
16
17
BUF
REF
DOWNLOADER
DEBUGGER
PROG.
CLOCK
DIVIDER
C
REF
D1
SPI SERIAL
INTERFACE
ASYNCHRONOUS
SERIAL PORT
(UART)
OSC
AND
PLL
POR
Figure 17. ADuC814 Block Diagram
Rev. A | Page 16 of 72
ADuC814
MEMORY ORGANIZATION
DATA MEMORY SPACE
READ/WRITE
The ADuC814 does not have Port 0 and Port 2 pins and
therefore does not support external program or data memory
interfaces. The device executes code from the internal 8-kByte
Flash/EE program memory. This internal code space can be
programmed via the UART serial port interface while the device
is in-circuit. The program memory space of the ADuC814 is
shown in Figure 18.
9FH
(PAGE 159)
640 BYTES
FLASH/EE DATA
MEMORY
ACCESSED
INDIRECTLY
VIA SFR
CONTROL REGISTERS
00H
(PAGE 0)
PROGRAM MEMORY SPACE
READ-ONLY
INTERNAL
DATA MEMORY
SPACE
1FFFH
FFH
FFH
SPECIAL
FUNCTION
REGISTERS
ACCESSIBLE
BY DIRECT
ADDRESSING
ONLY
ACCESSIBLE
BY
INDIRECT
ADDRESSING
ONLY
UPPER
128
INTERNAL
8 kBYTE
FLASH/EE
PROGRAM
MEMORY
80H
7FH
80H
ACCESSIBLE
BY
DIRECT
AND INDIRECT
ADDRESSING
LOWER
128
00H
0000H
Figure 19. Data Memory Map
Figure 18. Program Memory Map
The lower 128 bytes of internal data memory are mapped as
shown in Figure 20. The lowest 32 bytes are grouped into four
banks of eight registers addressed as R0 to R7. The next 16 bytes
(128 bits), locations 20H to 2FH above the register banks, form
a block of directly addressable bit locations at bit addresses 00H
through 7FH. The stack can be located anywhere in the internal
memory address space, and the stack depth can be expanded up
to 256 bytes.
The data memory address space consists of internal memory
only. The internal memory space is divided into four physically
separate and distinct blocks, namely the lower 128 bytes of
RAM, the upper 128 bytes of RAM, the 128 bytes of special
function register (SFR) area, and a 640-byte Flash/EE data
memory. While the upper 128 bytes of RAM and the SFR area
share the same address locations, they are accessed through
different addressing modes.
7FH
The lower 128 bytes of data memory can be accessed through
direct or indirect addressing, the upper 128 bytes of RAM can
be accessed through indirect addressing, and the SFR area is
accessed through direct addressing.
GENERAL-PURPOSE
AREA
30H
2FH
BIT-ADDRESSABLE
BANKS
SELECTED
VIA
BIT ADDRESSES
Also, as shown in Figure 19, an additional 640 bytes of Flash/EE
data memory are available to the user and can be accessed
indirectly via a group of control registers mapped into the SFR
area. Access to the Flash/EE data memory is discussed in detail
later as part of the Flash/EE Memory section.
20H
18H
10H
BITS IN PSW
1FH
17H
0FH
07H
11
10
01
00
FOUR BANKS OF EIGHT
REGISTERS
R0 R7
08H
00H
RESET VALUE OF
STACK POINTER
Figure 20. Lower 128 Bytes of Internal Data Memory
RESET initializes the stack pointer to location 07H and incre-
ments it once to start from location 08H, which is also the first
register (R0) of Register Bank 1. If more than one register bank
is being used, the stack pointer should be initialized to an area
of RAM not used for data storage.
Rev. A | Page 17 of 72
ADuC814
The SFR space is mapped to the upper 128 bytes of internal
data memory space and is accessed by direct addressing only. It
provides an interface between the CPU and all on-chip periph-
erals. A block diagram showing the programming model of the
ADuC814 via the SFR area is shown in Figure 21. A complete
SFR map is shown in Figure 22.
OVERVIEW OF MCU-RELATED SFRS
Accumulator SFR
ACC is the accumulator register and is used for math operations
including addition, subtraction, integer multiplication and
division, and Boolean bit manipulations. The mnemonics for
accumulator-specific instructions refer to the accumulator as A.
B SFR
640-BYTE
ELECTRICALLY
8-kBYTE
The B register is used with the ACC for multiplication and
division operations. For other instructions it can be treated as a
general-purpose scratchpad register.
REPROGRAMMABLE
ELECTRICALLY
NONVOLATILE
REPROGRAMMABLE
FLASH/EE DATA
NONVOLATILE
MEMORY
FLASH/EE PROGRAM
MEMORY
Stack Pointer SFR
6-CHANNEL
12-BIT SAR ADC
The SP register is the stack pointer and is used to hold an internal
RAM address called the top of the stack. The SP register is
incremented before data is stored during PUSH and CALL
executions. While the stack may reside anywhere in on-chip
RAM, the SP register is initialized to 07H after a reset. This
causes the stack to begin at location 08H.
128-BYTE
SPECIAL
FUNCTION
REGISTER
AREA
8051
COMPATIBLE
CORE
OTHER ON-CHIP
PERIPHERALS
TEMPERATURE
MONITOR
DUAL 12-BIT DAC
SERIAL I/O
WDT
256 BYTES
RAM
Data Pointer
PSM
TIC
PLL
The data pointer is made up of two 8-bit registers, named DPH
(high byte) and DPL (low byte). These registers provide memory
addresses for internal code access. The pointer may be manipu-
lated as a 16-bit register (DPTR = DPH, DPL), or as two inde-
pendent 8-bit registers (DPH, DPL).
Figure 21. Programming Model
Program Status Word SFR
The program status word (PSW) register is the program status word that contains several bits reflecting the current status of the CPU as
detailed in Table 4.
SFR Address
Power-On Default
Bit Addressable
D0H
00H
Yes
CY
AC
F0
RS1
RS0
OV
F1
P
Table 4. PSW SFR Bit Designations
Bit No.
Name
Description
7
6
5
4
3
CY
AC
F0
RS1
RS0
Carry Flag.
Auxiliary Carry Flag.
General-Purpose Flag.
Register Bank Select Bits.
RS1
RS0
Selected Bank
0
0
1
1
0
1
0
1
0
1
2
3
2
1
0
OV
F1
P
Overflow Flag.
General-Purpose Flag.
Parity Bit.
Rev. A | Page 18 of 72
ADuC814
Power Control SFR
The power control (PCON) register contains bits for power-saving options and general-purpose status flags as shown in Table 5.
SFR Address
Power-On Default
Bit Addressable
87H
00H
No
SMOD
SERIPD
INT0PD
---
GF1
GF0
PD
IDL
Table 5. PCON SFR Bit Designations
Bit No.
Name
SMOD
SERIPD
INT0PD
RSVD
GF1
GF0
PD
IDL
Description
7
6
5
4
3
2
1
0
Double UART Baud Rate.
SPI Power-Down Interrupt Enable.
INT0 Power-Down Interrupt Enable.
Reserved.
General-Purpose Flag Bit.
General-Purpose Flag Bit.
Power-Down Mode Enable.
Idle Mode Enable.
Rev. A | Page 19 of 72
ADuC814
SPECIAL FUNCTION REGISTERS
Unoccupied locations in the SFR address space are not
implemented, i.e., no register exists at this location. If an
unoccupied location is read, an unspecified value is returned.
SFR locations reserved for future use are shaded (RESERVED)
and should not be accessed by the user software.
All registers, except the program counter and the four general-
purpose register banks, reside in the SFR area. The SFR registers
include control, configuration, and data registers that provide an
interface between the CPU and all on-chip peripherals.
Figure 22 shows a full SFR memory map and SFR contents on
RESET; NOT USED indicates unoccupied SFR locations.
SPICON1
DAC0L
DAC0H
DAC1L
DAC1H DACCON
RESERVED RESERVED
ISPI
FFH
WCOL SPE
SPIM CPOL CPHA SPR1 SPR05
BITS
0
0
0
0
FEH
0
FDH
0
0
0
0
FCH
F4H
ECH
E4H
0
0
0
0
FBH
0
FAH
F2H
EAH
E2H
1
0
0
0
0
0
0
F9H
F1H
E9H
E1H
0
0
0
0
0
0
F8H
F0H
E8H
E0H
0
0
0
0
0
0
F8H
04H F9H 00H FAH 00H FBH 00H FCH 00H FDH 04H
ADCOFSL ADCOFSH ADCGAINL ADCGAINH ADCCON3
00H F1H 00H F2H 20H F3H 00H F4H 00H F5H 00H
B1
SPIDAT
RESERVED
BITS
BITS
F7H
F6H
0
F5H
F3H
0
F0H
F7H 00H
DCON1
ADCCON1
D0
D1
EFH
D1EN
D0EN
EBH
RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED
EEH
0
EDH
0
EFH 00H
E8H
00H
ACC1
RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED
BITS
BITS
BITS
BITS
BITS
BITS
BITS
BITS
E7H
E6H
0
E5H
E3H
0
0
0
E0H
00H
ADCCON21 ADCDATAL ADCDATAH
PSMCON
DFH DEH
PLLCON
D7H 53H
ADCI ADCSPI CCONV SCONV CS3
DFH
CS2
DAH
CS1
D9H
CS0
D8H
RESERVED RESERVED RESERVED RESERVED
0
0
0
DEH
0
DDH
0
DCH
0
DBH
D8H
00H D9H 00H DAH 00H
PSW1
CY
D7H
AC
F0
RS1
D4H
RS0
D3H
OV
D2H
FI
D1H
P
D0H
RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED
D6H
0
D5H
0
0
D0H
00H
T2CON1
RCAP2L RCAP2H
TL2
TH2
TF2
CFH
EXF2 RCLK TCLK EXEN2 TR2
CNT2 CAP2
C9H
RESERVED
RESERVED RESERVED
CEH
0
CDH
0
CCH
0
CBH
0
CAH
0
C8H
0
C8H
00H
CAH 00H CBH 00H CCH 00H CDH 00H
CHIPID
WDCON1
C0H 10H
IP1
EDARL
PRE3 PRE2 PRE1 PRE0 WDIR WDS
WD WDWR
RESERVED
ECON
RESERVED NOT USED
RESERVED
RESERVED
C7H
0
C6H
0
C5H
0
C4H
1
C3H
0
C2H
0
C1H
0
C0H
0
C6H 00H
C2H 0XH
ETIM1
ETIM2
EDATA1 EDATA2 EDATA3 EDATA4
PSI
BFH
PADC
PT2
PS
PT1
PX1
PT0
PX0
0
BEH
0
BDH
0
BCH
0
BBH
0
BAH
0
B9H
0
B8H
0
BAH 00H
B8H
00H B9H 00H
BBH 00H BCH 00H BDH 00H BEH 00H BFH 00H
P31
RD
B7H
WR
T1
T0
INT1
INT0
TxD
RxD
RESERVED RESERVED RESERVED
NOT USED
RESERVED RESERVED RESERVED
1
0
B6H
1
B5H
1
0
B4H
1
0
B3H
1
0
B2H
1
B1H
1
0
B0H
1
0
B0H
FFH
IE1
IEIP2
EA
AFH
EADC
ET2
ES
ACH
ET1
ABH
EX1
AAH
ET0
A9H
EX0
A8H
RESERVED RESERVED
RESERVED RESERVED
RESERVED RESERVED
AEH
0
ADH
0
A8H 00H A9H A0H
HOUR
INTVAL
MIN
SEC
TIMECON HTHSEC
NOT USED
NOT USED
A6H
A1H
A5H 00H
00H
00H A2H
00H A3H 00H A4H 00H
SCON1
SBUF
I2CDAT
I2CADD
CFG814
SM0
9FH
SM1
9EH
SM2
9DH
REN
9CH
TB8
9BH
RB8
9AH
TI
99H
RI
98H
NOT USED NOT USED NOT USED
BITS
BITS
BITS
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
0
0
0
1
0
98H 00H 99H 00H 9AH 00H 9BH 55H
P11,2
9CH
04H
T2EX
91H
T2
90H
NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED
97H
96H
95H
94H
93H
92H
1
0
90H FFH
TCON1
TMOD
TL0
TL1
TH0
TH1
TF1
8FH
TR1
8EH
TF0
8DH
TR0
8CH
IE1
8BH
IT1
8AH
IE0
89H
IT0
88H
RESERVED RESERVED
PCON
88H 00H 89H 00H 8AH 00H 8BH 00H 8CH 00H 8DH 00H
SP
DPL
DPH
RESERVED RESERVED RESERVED
NOT USED
81H 07H 82H 00H 83H 00H
87H 00H
SFR MAP KEY:
THESE BITS ARE CONTAINED IN THIS BYTE.
MNEMONIC
TCON
IT0
88H
MNEMONIC
SFR ADDRESS
IE0
89H
0
0
DEFAULT VALUE
88H 00H
DEFAULT VALUE
SFR ADDRESS
Figure 22. Special Function Register Locations and Reset Values
Note the following about SFRs:
•
•
•
•
SFRs whose address ends in 0H or 8H are bit addressable.
Only P1.0 and P1.1 can operate as digital I/O pins. P1.2–P1.7 can be configured as analog inputs (ADC inputs) or as digital inputs.
The CHIPID SFR contains the silicon revision ID byte and may change for future silicon revisions.
These registers are reconfigured at power-on with factory calculated calibration coefficients that can be overwritten by user code. See
the calibration options in ADCCON3 SFR.
SS
•
When the SPIM bit in the SPICON SFR is cleared, the SPR0 bit reflects the level on the pin (Pin 22).
Rev. A | Page 20 of 72
ADuC814
ADC CIRCUIT INFORMATION
GENERAL OVERVIEW
ADC TRANSFER FUNCTION
The ADC block incorporates a 4.05 msec, 6-channel, 12-bit
resolution, single-supply ADC. This block provides the user
with a multichannel multiplexer, track-and-hold amplifier, on-
chip reference, offset calibration features and ADC. All compo-
nents in this block are easily configured via a 3-register SFR
interface.
The analog input range for the ADC is 0 V to VREF. For this
range, the designed code transitions occur midway between
successive integer LSB values, i.e., 1/2 LSB, 3/2 LSBs, 5/2 LSBs . . .
FS –3/2 LSBs. The output coding is straight binary with 1 LSB =
FS/4096 or 2.5 V/4096 = 0.61 mV when VREF = 2.5 V. The ideal
input/output transfer characteristic for the 0 V to VREF range is
shown in Figure 23.
The ADC consists of a conventional successive-approximation
converter based around a capacitor DAC. The converter accepts
an analog input range of 0 V to VREF. A precision, factory cali-
brated 2.5 V reference is provided on-chip. An external reference
may also be used via the external VREF pin. This external refer-
OUTPUT
CODE
111...111
111...110
111...101
111...100
ence can be in the range 1.0 V to AVDD
.
FS
1LSB =
4096
Single or continuous conversion modes can be initiated in
software. In hardware, a convert signal can be applied to an
external pin (CONVST), or alternatively Timer 2 can be config-
ured to generate a repetitive trigger for ADC conversions.
000...011
000...010
000...001
000...000
The ADuC814 has a high speed ADC to SPI interface data
capture logic implemented on-chip. Once configured, this logic
transfers the ADC data to the SPI interface without the need for
CPU intervention.
0V 1LSB
+FS
VOLTAGE INPUT
Figure 23. ADuC814 ADC Transfer Function
The ADC has six external input channels. Two of the ADC
channels are multiplexed with the DAC outputs, ADC4 with
DAC0, and ADC5 with DAC1. When the DAC outputs are in
use, any ADC conversion on these channels represents the DAC
output voltage. Due care must be taken to ensure that no
external signal is trying to drive these ADC/DAC channels
while the DAC outputs are enabled.
ADC Data Output Format
Once configured via the ADCCON1–3 SFRs, the ADC converts
the analog input and provides an ADC 12-bit result word in the
ADCDATAH/L SFRs. The ADCDATAL SFR contains the
bottom 8 bits of the 12-bit result. The bottom nibble of the
ADCDATAH SFR contains the top 4 bits of the result, while the
top nibble contains the channel ID of the ADC channel which
has been converted on. This ID corresponds to the channel
selection bits CD3–CD0 in the ADCCON2 SFR. The format of
the ADC 12-bit result word is shown in Figure 24.
In addition to the six external channels of the ADC, five internal
signals are also routed through the front end multiplexer. These
signals include a temperature monitor, DAC0, DAC1, VREF, and
AGND. The temperature monitor is a voltage output from an
on-chip band gap reference, which is proportional to absolute
temperature. These internal channels can be selected similarly
to the external channels via CS3–CS0 bits in the ADCCON2 SFR.
ADCDATAH SFR
CH–ID
TOP 4 BITS
HIGH 4 BITS OF
ADC RESULT WORD
ADCDATAL SFR
The ADuC814 is shipped with factory programmed offset and
gain calibration coefficients that are automatically downloaded
to the ADC on a power-on or RESET event, ensuring optimum
ADC performance. The ADC core contains automatic endpoint
self-calibration and system calibration options that allow the
user to overwrite the factory programmed coefficients if desired
and tailor the ADC transfer function to the system in which it is
being used.
LOW 8 BITS OF THE
ADC RESULT WORD
Figure 24. ADC Result Format
Rev. A | Page 21 of 72
ADuC814
SFR INTERFACE TO ADC BLOCK
The ADC operation is fully controlled via three SFRs: ADCCON1, ADCCON2, and ADCCON3. These three registers control the mode
of operation.
ADCCON1 (ADC CONTROL SFR 1)
The ADCCON1 register controls conversion and acquisition times, hardware conversion modes, and power-down modes as detailed
below.
SFR Address
SFR Power-on Default
Bit Addressable
EFH
00H
No
MODE
EXT_REF
CK1
CK0
AQ1
AQ0
T2C
EXC
Table 6. ADCCON1 SFR Bit Designations
Bit No.
Name
Description
7
MODE
Mode Bit.
This bit selects the operating mode of the ADC.
Set to 1 by the user to power on the ADC.
Set to 0 by the user to power down the ADC.
External Reference Select Bit.
6
EXT_REF
This bit selects which reference the ADC uses when performing a conversion.
Set to 1 by the user to switch in an external reference.
Set to 0 by the user to switch in the on-chip band gap reference.
ADC Clock Divide Bits.
CK1 and CK0 combine to select the divide ratio for the PLL master clock used to generate the ADC clock. To ensure
correct ADC operation, the divider ratio must be chosen to reduce the ADC clock to 4.5 MHz and below. The
divider ratio is selected as follows:
5
4
CK1
CK0
CK1
0
CK0
0
PLL Divider
8
0
1
4
1
1
0
1
16
32
3
2
AQ1
AQ0
The ADC Acquisition Time Select Bits.
AQ1 and AQ0 combine to select the number of ADC clocks required for the input track-and-hold amplifier to
acquire the input signal. The acquisition time is selected as follows:
AQ1
AQ0
No. ADC Clks
0
0
1
1
0
1
0
1
1
2
3
4
1
0
T2C
EXC
The Timer2 Conversion Bit.
T2C is set to enable the Timer2 overflow bit to be used as the ADC convert start trigger input.
The External Trigger Enable Bit.
EXC is set to allow the external CONVST pin be used as the active low convert start trigger input. When enabled, a
rising edge on this input pin trigger a conversion. This pin should remain low for a minimum pulse width of
100 nsec at the required sample rate.
Rev. A | Page 22 of 72
ADuC814
ADCCON2 (ADC CONTROL SFR 2)
The ADCCON2 (byte addressable) register controls ADC channel selection and conversion modes as detailed below.
SFR Address
SFR Power-On Default
Bit Addressable
D8H
00H
Yes
ADCI
ADCSPI
CCONV
SCOVC
CS3
CS2
CS1
CS0
Table 7. ADCCON2 SFR Bit Designations
Bit No.
Name
Description
7
ADCI
ADC Interrupt Bit.
ADCI is set at the end of a single ADC conversion cycle. If the ADC interrupt is enabled, the ADCI bit is cleared when
user code vectors to the ADC interrupt routine. Otherwise the ADCI bit should be cleared by the user code.
6
5
ADCSPI
CCONV
ADCSPI Mode Enable Bit.
ADCSPI is set to enable the ADC conversion results to be transferred directly to the SPI data buffer (SPIDAT) without
intervention from the CPU.
Continuous Conversion Bit.
CCONV is set to initiate the ADC into a continuous mode of conversion. In this mode the ADC starts converting
based on the timing and channel configuration already set up in the ADCCON SFRs. The ADC automatically starts
another conversion once a previous conversion cycle has completed. When operating in this mode from 3 V
supplies, the ADC should be configured for ADC clock divide of 16 using CK1 and CK0 bits in ADCCON1, and ADC
acquisition time should be set to four ADC clocks using AQ1, AQ0 bits in ADCCON1 SFR.
4
SCONV
Single Conversion Bit.
SCONV is set to initiate a single conversion cycle. The SCONV bit is automatically reset to 0 on completion of the
single conversion cycle. When operating in this mode from 3 V supplies, the maximum ADC sampling rate should
not exceed 147 kSPS.
3
2
1
0
CS3
CS2
CS1
CS0
Channel Selection Bits.
CS3–CS0 allow the user to program the ADC channel selection under software control. Once a conversion is
initiated, the channel converted is pointed to by these channel selection bits.
The Channel Select bits operate as follows:
CS3
0
0
0
0
0
0
0
0
CS2
0
0
0
0
1
1
1
1
CS1
0
0
1
1
0
0
1
1
CS0
0
1
0
1
0
1
0
1
CHANNEL
0
1
2
3
4
5
X
X
Not a vaild selection. No ADC channel selected.
Not a valid selection. No ADC channel selected.
1
0
0
0
Temperature Sensor
1
1
1
1
0
0
0
1
0
1
1
0
1
0
1
0
DAC0
DAC1
AGND
VREF
Rev. A | Page 23 of 72
ADuC814
ADCCON3 (ADC CONTROL SFR 3)
The ADCCON3 register controls the operation of various calibration modes as well as giving an indication of ADC busy status.
SFR Address
SFR Power-On Default
F5H
00H
BUSY
GNCLD
AVGS1
AVGS0
OFCLD
MODCAL
TYPECAL
SCAL
Table 8. ADCCON3 SFR Bit Designations
Bit No.
Name
Description
7
BUSY
ADC Busy Status Bit.
BUSY is a read-only status bit that is set during a valid ADC conversion or calibration cycle.
Busy is automatically cleared by the core at the end of a conversion or calibration cycle.
Gain Calibration Disable Bit.
6
GNCLD
This bit enables/disables the gain calibration coefficients from affecting the ADC results.
Set to 0 to enable gain calibration coefficient
Set to 1 to disable gain calibration coefficient.
5
4
AVGS1
AVGS0
Number of Averages Selection Bits.
This bit selects the number of ADC readings averaged for each bit decision during a calibration cycle.
AVGS1 AVGS0 Number of Averages
0
0
1
1
0
1
0
1
15
1
31
63
3
OFCLD
Offset Calibration Disable Bit.
This bit enables/disables the offset calibration coefficients from affecting the ADC results.
Set to 0 to enable offset calibration coefficient.
Set to 1 to disable the offset calibration coefficient
Calibration Mode Select Bit.
This bit should be set to 1 for all calibration cycles.
Calibration Type Select Bit.
2
1
MODCAL
TYPECAL
This bit selects between offset (zero-scale) and gain (full-scale) calibration.
Set to 0 for offset calibration.
Set to 1 for gain calibration.
0
SCAL
Start Calibration Cycle Bit.
When set, this bit starts the selected calibration cycle.
It is automatically cleared when the calibration cycle is completed.
Rev. A | Page 24 of 72
ADuC814
DRIVING THE ADC
The ADC incorporates a successive approximation architecture
(SAR) involving a charge-sampled input stage. Each ADC con-
version is divided into two distinct phases as defined by the
position of the switches in Figure 25. During the sampling
phase (with SW1 and SW2 in the track position), a charge
proportional to the voltage on the analog input is developed
across the input sampling capacitor. During the conversion
phase (with both switches in the hold position), the capacitor
DAC is adjusted via internal SAR logic until the voltage on
Node A is zero, indicating that the sampled charge on the input
capacitor is balanced out by the charge being output by the
capacitor DAC. The digital value finally contained in the SAR is
then latched out as the result of the ADC conversion. Control of
the SAR, and timing of acquisition and sampling modes, is han-
dled automatically by built-in ADC control logic. Acquisition and
conversion times are also fully configurable under user control.
ADuC814
10Ω
AIN0
0.1µF
Figure 26. Buffering Analog Inputs
At first glance the circuit in Figure 26 may look like a simple
anti-aliasing filter, it actually serves no such purpose. Though
the R/C does help to reject some incoming high frequency noise,
its primary function is to ensure that the transient demands of
the ADC input stage are met. It does so by providing a capacitive
bank from which the 32 pF sampling capacitor can draw its
charge. Since the 0.1 µF capacitor in Figure 26 is more than
3000 times the size of the 32 pF sampling capacitor, its voltage
does not change by more than one count of the 12-bit transfer
function when the 32 pF charge from a previous channel is
dumped onto it. A larger capacitor can be used if desired, but
care needs to be taken if choosing a larger resistor (see Table 9).
ADuC814
V
REF
AGND
DAC1
INTERNAL
CHANNELS
DAC0
TEMPERATURE MONITOR
AIN5
AIN0
The Schottky diodes in Figure 26 may be necessary to limit the
voltage applied to the analog input pin as per the Absolute
Maximum Ratings. They are not necessary if the op amp is
powered from the same supply as the ADuC814 because, in that
case, the op amp is unable to generate voltages above VDD or
below ground. An op amp of some kind is necessary unless the
signal source is very low impedance to begin with. DC leakage
currents at the ADuC814 analog inputs can cause measurable
dc errors with external source impedances as little as 100 Ω or
so. To ensure accurate ADC operation, keep the total source
impedance at each analog input less than 61 Ω. Table 9 illustrates
examples of how source impedance can affect dc accuracy.
200Ω
CAPACITOR
DAC
TRACK
HOLD
COMPARATOR
32pF
200Ω
TRACK
HOLD
AGND
Figure 25. Internal ADC Structure
Note that whenever a new input channel is selected, a residual
charge from the 32 pF sampling capacitor places a transient on
the newly selected input. The signal source must be capable of
recovering from this transient before the sampling switches
click into hold mode. Delays can be inserted in software
(between channel selection and conversion request) to account
for input stage settling, but a hardware solution alleviates this
burden from the software design task and ultimately results in a
cleaner system implementation.
Table 9. Source Impedance Errors
Source
Impedance
Error from 1 µA
Leakage Current
Error from 10 µA
Leakage Current
61 Ω
610 Ω
61 µV = 0.1 LSB
610 µV = 1 LSB
610 µV = 1 LSB
6.1 mV = 10 LSB
Although Figure 26 shows the op amp operating at a gain of 1,
you can configure it for any gain needed. Also, you can just as
easily use an instrumentation amplifier in its place to condition
differential signals. Use any modern amplifier that is capable of
delivering the signal (0 V to VREF) with minimal saturation.
Some single-supply, rail-to-rail op-amps that are useful for this
purpose include, but are certainly not limited to, the ones given
in Table 10. Check the Analog Devices literature (CD ROM data
book, etc.) for details on these and other op amps and
instrumentation amps.
One hardware solution is to choose a very fast settling op amp
to drive each analog input. Such an op amp would need to fully
settle from a small signal transient in less than 300 ns in order
to guarantee adequate settling under all software configurations.
A better solution, recommended for use with any amplifier, is
shown in Figure 26.
Rev. A | Page 25 of 72
ADuC814
Table 10. Some Single-Supply Op Amps
If an external voltage reference is preferred, it should be con-
nected to the VREF and CREF pins as shown in Figure 28. Bit 6 of
the ADCCON1 SFR must be set to 1 to switch in the external
reference voltage. To ensure accurate ADC operation, the
voltage applied to VREF must be between 1.0 V and AVDD. In
situations where analog input signals are proportional to the
power supply (such as some strain gage applications) it can be
Op Amp Model
Characteristics
OP281/OP481
Micropower
OP191/OP291/OP491
OP196/OP296/OP496
OP183/OP283
OP162/OP262/OP462
AD820/OP822/OP824
AD823
I/O good up to VDD, low cost
I/O to VDD, micropower, low cost
High gain-bandwidth product
High GBP, micropackage
FET input, low cost
desirable to connect the VREF pin directly to AVDD
.
FET input, high GBP
ADuC814
V
DD
Keep in mind that the ADC’s transfer function is 0 V to VREF
,
EXTERNAL
VOLTAGE
REFERENCE
2.5V
BAND GAP
REFERENCE
and any signal range lost to amplifier saturation near ground
impacts dynamic range. Though the op amps in Table 10 are
capable of delivering output signals very closely approaching
ground, no amplifier can deliver signals all the way to ground
when powered by a single supply. Therefore, if a negative supply
is available, one could consider using it to power the front end
amplifiers. If you do, however, be sure to include the Schottky
diodes shown in Figure 26 (or at least the lower of the two
diodes) to protect the analog input from undervoltage conditions.
BUFFER
0 = INTERNAL
TO ADC
REFERENCE
INPUT
V
REF
1 = EXTERNAL
ADCCON1.6
0.1µF
C
REF
0.1µF
Figure 28. Using an External Voltage Reference
VOLTAGE REFERENCE CONNECTIONS
Operation of the ADC with a reference voltage below 1.0 V,
however, may incur loss of accuracy eventually resulting in
missing codes or non-monotonicity. For that reason, do not use
a reference voltage less than 1.0 V.
The on-chip 2.5 V band gap voltage reference can be used as the
reference source for the ADC and DACs. To ensure the accuracy
of the voltage reference, decouple the VREF and the CREF pin to
ground with 0.1 µF capacitors as shown in Figure 27.
CONFIGURING THE ADC
ADuC814
In configuring the ADC a number of parameters need to be set
up. These parameters can be configured using the three SFRs:
ADCCON1, ADCCON2, and ADCCON3, which are detailed in
the following sections.
2.5V
BAND GAP
REFERENCE
The ADCCLK determines the speed at which the ADC logic
runs while performing an ADC conversion. All ADC timing
parameters are calculated from the ADCCLK frequency. On the
ADuC814, the ADCCLK is derived from the maximum core
frequency (FCORE), 16.777216 MHz. The ADCCLK frequency is
selected via ADCCON1 Bits 5 and 4, which provide four core
clock divide ratios of 8, 4, 16, and 32, generating ADCCLK
values of 2 MHz, 4 MHz, 1 MHz, and 500 kHz, respectively.
BUFFER
TO ADC
REFERENCE
INPUT
V
REF
0.1µF
C
REF
0.1µF
BUFFER
Figure 27. Decoupling VREF and CREF
The acquisition time (TACQ) is the number of ADCCLKs that
the ADC input circuitry uses to sample the input signal. In most
cases, an acquisition time of one ADCCLK provides more than
adequate time for the ADuC814 to acquire its signal before
switching the internal track-and-hold amplifier into hold mode.
The only exception is a high source impedance analog input,
but this should be buffered first anyway because high source
impedances can cause significant dc errors (see Table 6).
ADCCON1 Bits 3 and 2 are used to select acquisition times of
1, 2, 3, and 4 ADCCLKs.
If the internal voltage reference is to be used as a reference for
external circuitry, the CREF output should be used. However, a
buffer must be used in this case to ensure that no current is
drawn from the CREF pin itself. The voltage on the CREF pin is
that of an internal node within the buffer block, and its voltage
is critical to ADC and DAC accuracy. As outlined in the
Reference Input/Output section of the Specifications table, the
internal band gap reference takes typically 80 msecs to power
on and settle to its final value. To ensure accurate ADC operation,
one should wait for the ADC to settle after power-on.
Rev. A | Page 26 of 72
ADuC814
Both the ADCCLK frequency and the acquisition time are used
in determining the ADC conversion time. Two other parameters
are also used in this calculation. To convert the acquired signal
into its corresponding digital output word takes 15 ADCCLK
periods (TCONV). When a conversion is initiated, the start of
conversion signal is synchronized to the ADCCLK. This synchro-
nization (TSYNC) can take from 0.5 to 1.5 ADCCLKs to occur.
The total ADC conversion time TADC is calculated using the
following formula:
results must be read from the ADCDATA SFRs before the next
conversion is completed to avoid loss of data. Continuous mode
can be stopped by clearing the CCONV bit.
An external signal can also be used to initiate ADC conversions.
Setting Bit 0 in ADCCON1 enables the logic to allow an
CONVST
external start-of-conversion signal on Pin 7 (
). This
active low pulse should be at least 100 ns wide. The rising edge
of this signal initiates the conversion.
Timer 2 can also be used to initiate conversions. Setting Bit 1
of ADCCON1 enables the Timer 2 overflow signal to start a
conversion. For Timer 2 configuration information, see the
Timers/Counters section.
T
ADC = TSYNC + TACQ + TCONV
Assuming TSYNC = 1, TACQ = 1 and FCORE/ADCCLK divider of 4.
The total conversion time is calculated by
TADC = (1 + 1 + 15) × (1 / 4194304)
CONVST
For both external
and Timer 2 overflow, the conver-
sion rate must be equal to or greater than the conversion time
(TADC) to avoid incorrect ADC results.
TADC = 4.05 µs
These settings allow a maximum conversion speed or sampling
rate of 246.7 kHz.
When initiating conversions, the user must ensure that only one
of the trigger modes is active at any one time. Initiating conver-
sions with more than one of the trigger modes active results in
erratic ADC behavior.
When converting on the temperature monitor channel, the
conversion time is not controlled via the ADCCON registers. It
is controlled in hardware and sets the ADCCLK to FCORE /32
and uses four acquisition clocks, giving a total ADC conversion
time of
ADC HIGH SPEED DATA CAPTURE MODE
The on-chip ADC has been designed to run at a maximum
conversion speed of 4.05 µs (247 kHz sampling rate). When
converting at this rate, the ADuC814 MCU has 4.05 µs to read
the ADC result and store it in memory for further post
processing; otherwise the next ADC sample could be lost. The
time to complete a conversion and store the ADC results
without errors is known as the throughput rate. In an interrupt
driven routine, the MCU also has to jump to the ADC interrupt
service routine, which decreases the throughput rate of the
ADuC814. In applications where the ADuC814 standard
operating mode throughput is not fast enough, an ADC high
speed data capture (HSDC) mode is provided.
TADC = (1 + 4 + 15) × (1 / 524288) = 38.14 µs
Increasing the conversion time on the temperature monitor
channel improves the accuracy of the reading. To further
improve the accuracy, an external reference with low tempera-
ture drift should also be used.
INITIATING ADC CONVERSIONS
After the ADC has been turned on and configured, there are
four methods of initiating ADC conversions.
Single conversions can be initiated in software by setting the
SCONV bit in the ADCCON2 register via user code. This
causes the ADC to perform a single conversion and puts the
result into the ADCDATAH/L SFRs. The SCONV bit is cleared
as soon as the ADCDATA SFRs have been updated.
In HSDC mode, ADC results are transferred to the SPI logic
without intervention from the ADuC814 core logic. In applica-
tions where the ADC throughput is slow, the HSDC logic operates
in non-pipelined mode (Figure 29). In this mode, there is
adequate time for the ADC conversion and the ADC-to-SPI
data transfer to complete before the next start of conversion. As
the ADC throughput increases, the HSDC logic begins to operate
in pipelined mode as shown in Figure 30.
Continuous conversion mode can be initiated by setting the
CCONV bit in ADCCON2 via user code. This performs back-
to-back conversions at the configured rate (246.7 kHz for the
settings detailed previously). In continuous mode, the ADC
CONVST
BUSY
SCLOCK
MOSI
ADCDATAH
ADCDATAL
Figure 29. High Speed Data Capture Logic Timing (Non-Pipelined Mode)
Rev. A | Page 27 of 72
ADuC814
CONVST
BUSY
SCLOCK
MOSI
ADCDATAH
ADCDATAL
ADCDATAH
ADCDATAL
ADCDATAH
ADCDATAL
Figure 30. High Speed Data Capture Logic Timing (Pipelined Mode)
In this mode, the ADC to SPI data transfer occurs during the
next ADC conversion. To avoid loss of an ADC result, the user
must ensure that the ADC to SPI transfer rate is complete
before the current ADC conversion ends.
As part of internal factory final test routines, the ADuC814 is
calibrated to its offset and gain specifications. The offset and
gain coefficients obtained from this factory calibration are
stored in non-volatile Flash/EE memory. These are downloaded
from the Flash/EE memory to offset and gain calibration
registers automatically on a power-up or a reset event.
To enable HSDC mode, Bit 6 in ADCCON2 (ADCSPI) must be
set and to enable the ADuC814 to capture a contiguous sample
stream at full ADC update rates (247 kHz).
In many applications these factory-generated calibration
coefficients suffice. However, the ADuC814 ADC offset and
gain accuracy may vary from system to system due to board
layout, grounding, clock speed, or system configuration, and so
on. To get the best ADC accuracy in your system, an ADC
calibration should be performed.
To configure the ADuC814 in HSDC mode:
1. The ADC must be put into one of its conversion modes.
2. The SPI interface must be configured. (The SPI configura-
tion is detailed in the Serial Peripheral Interface section).
Two main advantages are derived from ensuring the ADC
calibration registers are initialized correctly. First, the internal
errors in the ADC can be reduced significantly to give superior
dc performance; and second, system offset and gain errors can
be removed. This allows the user to remove reference errors
(whether an internal or external reference) and to use the full
dynamic range of the ADC by adjusting the analog input range
of the part for a specific system.
3. Enable HSDC by setting the ADCSPI bit in the ADCCON2
SFR.
4. Apply trigger signal to the ADC to perform conversions.
Once configured and enabled, the ADC results are transferred
from the ADCDATAH/L SFRs to the SPIDAT register. Figure 31
shows the HSDC logic configuration once the mode is enabled.
The ADC result is transmitted most significant bit first. In this
case, the channel ID is transmitted first, followed by the 12-bit
ADC result. When this mode is enabled, normal SPI and Port 3
operation is disabled; however, the core is free to continue code
execution, including general housekeeping and communication
tasks. This mode is disabled by clearing the ADCSPI bit.
ADC OFFSET AND GAIN CALIBRATION
COEFFICIENTS
The ADuC814 has two ADC calibration coefficients, one for
offset calibration and one for gain calibration. Both the offset
and gain calibration coefficients are 14-bit words, and each is
stored in two registers located in the special function register
(SFR) area. The offset calibration coefficient is divided into
ADCOFSH (6 bits) and ADCOFSL (8 bits), and the gain cali-
bration coefficient is divided into ADCGAINH (6 bits) and
ADCGAINL (8 bits).
8
8
0
16
ADC
EDC
8
SPIDAT
8
8
SPI LOGIC
DATA
REGISTER
1
8
END OF
0
1
The offset calibration coefficient compensates for dc offset
errors in both the ADC and the input signal. Increasing the
offset coefficient compensates for positive offset, and effectively
pushes down the ADC transfer function. Decreasing the offset
coefficient compensates for negative offset, and effectively pushes
up the ADC transfer function. The maximum offset that can be
compensated is typically 3.5ꢀ of VREF, which equates to typi-
cally 87.5 mV with a 2.5 V reference.
CONVERSION
SIGNAL
ADC TO SPI CONTROL LOGIC
Figure 31. High Speed Data Capture Logic
ADC OFFSET AND GAIN CALIBRATION OVERVIEW
Similarly, the gain calibration coefficient compensates for dc
gain errors in both the ADC and the input signal. Increasing the
gain coefficient compensates for a smaller analog input signal
range and scales up the ADC transfer function, effectively
increasing the slope of the transfer function. Decreasing the
The ADC block incorporates calibration hardware and
associated SFRs, which ensures optimum offset and gain
performance from the ADC at all times.
Rev. A | Page 28 of 72
ADuC814
gain coefficient compensates for a larger analog input signal
range and scales down the ADC transfer function, effectively
decreasing the slope of the transfer function. The maximum
analog input signal range for which the gain coefficient can
compensate is 1.035 × VREF, and the minimum input range is
0.965 × VREF, which equates to typically 3.5ꢀ of the reference
voltage.
To perform device offset calibration:
MOV ADCCON2,#0BH
MOV ADCCON3,#25H
;select internal AGND
;select offset calibration,
;31 averages per bit,
;offset calibration
To perform device gain calibration:
CALIBRATING THE ADC
MOV ADCCON2,#0CH
ADCCON3,#27H
;select internal VREF MOV
The ADuC814 has two hardware calibration modes, device
calibration and system calibration, that can be easily initiated by
the user software. The ADCCON3 SFR is used to calibrate the
ADC. See Table 8.
;select offset calibration,
;31 averages per bit,
;offset calibration
Device calibration is so called because the relevant signals used
for the calibration are available internally to the ADC. This
calibration method can be used to compensate for significant
changes in operating conditions, such as core frequency, analog
input range, reference voltage and supply voltages. In this
calibration mode, offset calibration uses internal AGND
selected via the ADCCON2 register bits CS3–CS0 (1011), and
gain calibration uses internal VREF selected by CS3–CS0 (1100).
Offset calibration should be executed first, followed by gain
calibration.
To perform system offset calibration:
Connect system AGND to an ADC input (Channel 0 in this case).
MOV ADCCON2,#00H
MOV ADCCON3,#25H
;select external AGND
;select offset calibration,
;31 averages per bit
To perform system gain calibration:
Connect system VREF to an ADC input (Channel 1 in this case).
System calibration is so called because the AGND and VREF
required for calibration must be the system AGND and VREF
signals. These must be supplied in turn, externally, to the ADC
inputs. This calibration method can be used to compensate for
both internal and external system errors. To perform system
calibration using an external reference, tie system ground and
reference to any two of the six selectable inputs. Enable external
reference mode (ADCCON1.6). Select the channel connected to
AGND via CS3–CS0 and perform system offset calibration.
Select the channel connected to VREF via CS3–CS0 and perform
system gain calibration.
MOV ADCCON2,#01H
ADCCON3,#27H
;select external VREF MOV
;select offset calibration,
;31 averages / bit (NUMAV),
;offset calibration
The calibration cycle time TCAL is calculated by
CAL = 14 × ADCCLK × NUMAV × (16 + TACQ
T
)
For an ADCCLK/FCORE, divide ratio of 4, a TACQ = 1 ADCCLK,
NUMAV = 31, the calibration cycle time is
INITIATING CALIBRATION IN CODE
T
CAL = 14 × (1 / 4194304) × 31 × (16 + 1)
When calibrating the ADC, ADCCON1 should be set to the
configuration in which the ADC is used. The ADCCON3
register can then be used to configure and execute the offset
and gain calibration required in sequence.
TCAL = 1.76 mS
In a calibration cycle, the ADC busy flag (Bit 7), instead of
framing an individual ADC conversion as in normal mode, goes
high at the start of calibration and returns to zero only at the
end of the calibration cycle. It can therefore be monitored in
code to indicate when the calibration cycle is completed. The
following code can be used to monitor the BUSY signal during
a calibration cycle.
Configure the ADC as required. In this case, ADCCLK = /4,
acquisition time is set to 1 clock (TACQ), and ADC is enabled.
MOV ADCCON1,#0D0H
;ADC on, ADCCLK set to
;divide by 4, 1 acquisition
;clock (Tacq)
WAIT:
MOV A, ADCCON3
JB ACC.7, WAIT
;move ADCCON3 to A
;If bit 7 is set jump to
WAIT
;else continue
Rev. A | Page 29 of 72
ADuC814
NONVOLITILE FLASH/EE MEMORY
Endurance quantifies the ability of the Flash/EE memory to be
cycled through many program, read, and erase cycles. In real
terms, a single endurance cycle is composed of four
independent, sequential events:
FLASH/EE MEMORY OVERVIEW
The ADuC814 incorporates Flash/EE memory technology on-
chip to provide the user with nonvolatile, in-circuit reprogram-
mable code and data memory space.
1. Initial page erase sequence
2. Read/verify sequence
Flash/EE memory takes the flexible in-circuit reprogrammable
features of EEPROM and combines them with the space efficient/
density features of EPROM (see Figure 32).
3. Byte program sequence
4. Second read/verify sequence
Because Flash/EE technology is based on a single transistor cell
architecture, a Flash memory array such as EPROM can be
implemented to achieve the space efficiencies or memory
densities required by a given design.
In reliability qualification, every byte in both the program and
data Flash/EE memory is cycled from 00H to FFH until a first
fail is recorded signifying the endurance limit of the on-chip
Flash/EE memory.
Like EEPROM, flash memory can be programmed in-system at
a byte level, although it must first be erased; the erase being
performed in page blocks. Thus, flash memory is often and
more correctly referred to as Flash/EE memory.
As indicated in the Specifications tables, the ADuC814 Flash/EE
memory endurance qualification has been carried out in accor-
dance with JEDEC Specification A117 over the industrial
temperature range of –40°C to +125°C. The results allow the
specification of a minimum endurance figure over supply and a
temperature of 100,000 cycles, with an endurance figure of
700,000 cycles being typical of operation at 25°C.
EPROM
EEPROM
TECHNOLOGY
TECHNOLOGY
SPACE EFFICIENT/
DENSITY
IN-CIRCUIT
REPROGRAMMABLE
FLASH/EE MEMORY
TECHNOLOGY
Retention quantifies the ability of the Flash/EE memory to
retain its programmed data over time. Again, the ADuC814 has
been qualified in accordance with the formal JEDEC Retention
Lifetime Specification (A117) at a specific junction temperature
(TJ = 55°C). As part of this qualification procedure, the Flash/EE
memory is cycled to its specified endurance limit described
above, before data retention is characterized. This means that
the Flash/EE memory is guaranteed to retain its data for its full
specified retention lifetime every time the Flash/EE memory is
reprogrammed. It should be noted that retention lifetime, based
on an activation energy of 0.6 eV, derates with TJ as shown in
Figure 33.
Figure 32. Flash/EE Memory Development
Incorporated in the ADuC814, Flash/EE memory technology
allows the user to update program code space in-circuit without
the need to replace one-time programmable (OTP) devices at
remote operating nodes.
FLASH/EE MEMORY AND THE ADUC814
The ADuC814 provides two arrays of Flash/EE memory for
user applications. There are 8 kbytes of Flash/EE program space
provided on-chip to facilitate code execution, therefore removing
the requirement for an external discrete ROM device. The pro-
gram memory can be programmed using conventional third-
party memory programmers. This array can also be programmed
in-circuit, using the serial download mode provided.
300
250
200
ADI SPECIFICATION
100 YEARS MIN.
A 640-byte Flash/EE data memory space is also provided on-
chip. This may be used as a general-purpose nonvolatile
scratchpad area. User access to this area is via a group of six
SFRs. This space can be programmed at a byte level, although it
must first be erased in 4-byte pages.
AT T = 55°C
J
150
100
50
0
ADUC814 FLASH/EE MEMORY RELIABILITY
The Flash/EE program and data memory arrays on the
ADuC814 are fully qualified for two key Flash/EE memory
characteristics: Flash/EE memory cycling endurance and
Flash/EE memory data retention.
40
50
60
70
80
90
100
110
T
JUNCTION TEMPERATURE (°C)
J
Figure 33. Flash/EE Memory Data Retention
Rev. A | Page 30 of 72
ADuC814
5V
USING FLASH/EE PROGRAM MEMORY
V
DD
DATA
P3
The Flash/EE program memory array can be programmed in
one of two modes: serial downloading and parallel
programming.
GND
ADuC814
P1.1–P1.4
COMMAND
TIMING
GND
DLOAD
RESET
P1.0
Serial Downloading (In-Circuit Programming)
P1.5–P1.7
V
DD
As part of its factory boot code, the ADuC814 facilitates code
download via the standard UART serial port. Serial download
mode is automatically entered on power-up or during a
hardware RESET operation if the external DLOAD pin is pulled
high through an external resistor, as shown in Figure 34. Once
in this mode, the user can download code to the program
memory array while the device is sited in its target application
hardware. A PC serial download executable is provided as part
of the ADuC814 QuickStart development system. The Serial
Download protocol is detailed in a MicroConverter Applications
Note uC004 available from the ADI MicroConverter website at
www.analog.com/microconverter.
ENABLE
Figure 35. Flash/EE Memory Parallel Programming
FLASH/EE PROGRAM MEMORY SECURITY
The ADuC814 facilitates three modes of Flash/EE program
memory security, which are described in the following sections.
These modes can be independently activated, restricting access
to the internal code space. These security modes can be enabled
as part of the user interface available on all ADuC814 serial or
parallel programming tools referenced on the MicroConverter
website at www.analog.com/microconverter.
Lock Mode
This mode locks code in memory, disabling parallel program-
ming of the program memory, although reading the memory in
parallel mode is still allowed. This mode is deactivated by
initiating a CODE-ERASE command in serial download or
parallel programming modes.
Secure Mode
This mode locks code in memory, disabling parallel program-
ming (program and VERIFY/READ commands). This mode is
deactivated by initiating a CODE-ERASE command in serial
download or parallel programming modes.
PULL DLOAD HIGH VIA
DVDD
1kΩ
1kΩ RESISTOR DURING
RESET TO CONFIGURE
THE ADuC814 FOR
ADuC814
Serial Safe Mode
DLOAD
SERIAL DOWNLOAD MODE
This mode disables serial download capability on the device. If
serial safe mode is activated and an attempt is made to reset the
part into serial download mode, i.e., RESET asserted and de-
asserted with DLOAD high, the part interprets the serial
download reset as a normal reset only. It therefore does not
enter serial download mode but only executes a normal reset
sequence. Serial safe mode can be disabled only by initiating a
CODE-ERASE command in parallel programming mode.
Figure 34. Flash/EE Memory Serial Download Mode Programming
Parallel Programming
The parallel programming mode is fully compatible with
conventional third-party Flash or EEPROM device program-
mers. A block diagram of the external pin configuration
required to support parallel programming is shown in Figure 35.
The high voltage (12 V) supply required for Flash/EE
programming is generated using on-chip charge pumps to
supply the high voltage program lines.
Rev. A | Page 31 of 72
ADuC814
A block diagram of the SFR interface to the Flash/EE data
memory array is shown in Figure 37.
USING FLASH/EE DATA MEMORY
The user Flash/EE data memory array consists of 640 bytes that
are configured into 160 (00H to 9FH) 4-byte pages as shown in
Figure 36.
FUNCTION:
FUNCTION:
HOLDS THE 8-BIT PAGE
ADDRESS POINTER
HOLDS THE 4-BYTE
PAGE DATA
9FH
BYTE 1 BYTE 2 BYTE 3 BYTE 4
9FH
BYTE 1 BYTE 2 BYTE 3 BYTE 4
EADRL
EDATA1 (BYTE 1)
EDATA2 (BYTE 2)
EDATA3 (BYTE 3)
EDATA4 (BYTE 4)
00H
BYTE 1 BYTE 2 BYTE 3 BYTE 4
00H
BYTE 1 BYTE 2 BYTE 3 BYTE 4
Figure 36. Flash/EE Data Memory Configuration
ECON COMMAND
INTERPRETER LOGIC
As with other ADuC814 user-peripheral circuits, the interface
to this memory space is via a group of registers mapped in the
SFR space. EADRL is used to hold the 8-bit address of the page
to be accessed. A group of four data registers (EDATA1–4) is
used to hold 4-byte page data just accessed. Finally, ECON is an
8-bit control register that may be written with one of five
Flash/EE memory access commands to trigger various read,
write, erase, and verify functions. These registers can be
summarized as follows:
FUNCTION:
INTERPRETS THE FLASH
COMMAND WORD
FUNCTION:
ECON
RECEIVES COMMAND DATA
Figure 37. Flash/EE Data Memory Control and Configuration
ECON—Flash/EE Memory Control SFR
This SFR acts as a command interpreter and may be written
with one of five command modes to enable various read,
program, and erase cycles as detailed in Table 11.
ECON
SFR Address B9H
Function
Default
Controls access to 640 bytes Flash/EE data space.
00H
EADRL
SFR Address C6H
Function
Holds the Flash/EE data page address.
(640 bytes = > 160 page addresses)
00H
Default
EDATA1–4
SFR Address BCH to BFH, respectively
Function
Holds Flash/EE data memory page write or page
read data bytes.
Default
EDATA1–4 > 00H
Table 11. ECON–Flash/EE Memory Control Register Command Modes
Command
Byte
01H
02H
Command Mode
READ
PROGRAM
Description
Results in 4 bytes being read into EDATA1–4 from memory page address contained in EADRL.
Results in 4 bytes (EDATA1–4) being written to memory page address in EADRL. This write command
assumes the designated write page has been erased.
03H
04H
Reserved
VERIFY
For internal use. 03H should not be written to the ECON SFR.
Allows the user to verify if data in EDATA1–4 is contained in page address designated by EADRL. A
subsequent read of the ECON SFR results in a zero being read if the verification is valid, a nonzero
value is read to indicate an invalid verification.
05H
06H
07H to FFH
ERASE
ERASE-ALL
Reserved
Results in an erase of the 4-byte page designated in EADRL.
Results in an erase of the full Flash/EE aata memory, 160-page (640 bytes) array.
For future use.
Rev. A | Page 32 of 72
ADuC814
FLASH/EE MEMORY TIMING
shipped from the factory pre-erased, i.e., byte locations set to
The typical program/erase times for the Flash/EE data memory
are
FFH, it is nonetheless good programming practice to include an
ERASE-ALL routine as part of any configuration/setup code
running on the ADuC814. An ERASE-ALL command consists
of writing 06H to the ECON SFR, which initiates an erasure of
all 640 byte locations in the Flash/EE array. This command
coded in 8051 assembly appears as
Erase Full Array (640 bytes)
Erase Single Page (4 bytes)
Program Page (4 bytes)
Read Page (4 bytes)
2 ms
2 ms
250 µs
Within single instruction cycle
MOV ECON, #06H
; Erase all Command
; 2 ms Duration
Programming a Byte
Using the Flash/EE Memory Interface
In general terms, a byte in the Flash/EE array can be programmed
only if it has been erased previously. To be more specific, a byte
can only be programmed if it already holds the value FFH.
Because of the Flash/EE architecture, this erasure must happen
at a page level; therefore, a minimum of four bytes (1 page) are
erased when an ERASE command is initiated.
As with all Flash/EE memory architectures, the array can be
programmed in-system at a byte level, although it must be
erased first, the erasure being performed in page blocks (4-byte
pages in this case).
A typical access to the Flash/EE data array involves setting up
the page address to be accessed in the EADRL SFR, configuring
the EDATA1–4 with data to be programmed to the array (the
EDATA SFRs are not written to for read accesses), and finally,
writing the ECON command word, which initiates one of the
modes shown Table 11.
A more specific example of the program-byte process is shown
below. In this example the user writes F3H into the second byte
on Page 03H of the Flash/EE data memory space while
preserving the other three bytes already in this page. Because
the user is required to modify only one of the page bytes, the
full page must be first read so that this page can then be erased
without the existing data being lost. This example, coded in
8051 assembly, appears as
Note that a given mode of operation is initiated as soon as the
command word is written to the ECON SFR. The core micro-
controller operation on the ADuC814 is idled until the
requested program/read or erase mode is completed. In
practice, this means that even though the Flash/EE memory
mode of operation is typically initiated with a two-machine
cycle MOV instruction (to write to the ECON SFR), the next
instruction cannot be executed until the Flash/EE operation is
complete (250 µs or 2 ms later). This means that the core does
not respond to interrupt requests until the Flash/EE operation is
complete, though the core peripheral functions like counter/
timers continue to count and time as configured throughout
this period. Although the 640-byte user Flash/EE array is
MOV EADRL,#03H
; Set Page Address
; Pointer
MOV ECON,#01H
MOV EDATA2,#0F3H
MOV ECON,#05H
MOV ECON,#02H
; Read Page
; Write New Byte
; Erase Page
; Write Page
; Program Flash/EE)
Rev. A | Page 33 of 72
ADuC814
USER INTERFACE TO OTHER ON-CHIP ADuC814 PERIPHERALS
(SFR) register, DACCON. Each DAC has two data registers,
This section gives a brief overview of the various peripherals
also available on-chip. A summary of the SFRs used to control
and configure these peripherals is also given.
DACxH/L. The DAC0 and DAC1 outputs share pins with ADC
inputs ADC4 and ADC5, respectively. When both DACs are on,
the number of analog inputs is reduced to four. Note that in
12-bit mode, the DAC voltage output is updated as soon as the
DACL data SFR has been written; therefore, the DAC data
registers should be updated as DACH first, followed by DACL.
DACS
The ADuC814 incorporates two 12-bit, voltage output DACs
on-chip. Each DAC has a rail-to-rail voltage output buffer capa-
ble of driving 10 kΩ/100 pF. They have two selectable ranges,
0 V to VREF (an external or the internal band gap 2.5 V
reference) and 0 V to AVDD, and can operate in 12-bit or 8-bit
modes. DAC operation is controlled by a single special function
When using the DACs on the VREF range it is necessary to power
up the ADC to enable the reference to the DAC section.
See Note 1.
DACCON
DAC Control Register
SFR Address
Power-On Default
Bit Addressable
FDH
04H
No
MODE
RNG1
RNG0
CLR1
CLR0
SYNC
PD1
PD0
Table 12. DACCON SFR Bit Designations
Bit No.
Name
Description
7
MODE
Mode Select Bit. Selects either 12-bit or 8-bit mode for both DACs.
Set to 1 by the user to enable 8-bit mode (DACxL is the active data register).
Set to 0 by the user to enable 12-bit mode.
6
5
4
3
2
RNG1
RNG0
CLR1
CLR0
SYNC
DAC1 Output Voltage Range Select Bit.
Set to 1 by the user to configure DAC1 range of 0 V to AVDD.
Set to 0 by the user to configure DAC1 range of 0 V to 2.5 V (VREF range) 1.
DAC0 Output Voltage Range Select Bit.
Set to 1 by he user to configure DAC0 range of 0 V to AVDD.
Set to 0 by the user to configure DAC0 range of 0 V to 2.5 V (VREF range) 1.
DAC1 Clear Bit.
Set to 1 by the user to enable normal DAC1 operation.
Set to 0 by the user to force DAC1 output voltage to 0 V.
DAC0 Clear Bit.
Set to 1 by the user to enable normal DAC0 operation.
Set to 0 by the user to force DAC0 output voltage to 0 V.
DAC0/1 Update Synchronization Bit.
Set to 1 by the user to enable asynchronous update mode. The DAC outputs update as soon as the DACxL SFRs are
written.
Set to 0 by the user to enable synchronous update mode. The user can simultaneously update both DACs by first
updating the DACxH/L SFRs while SYNC is 0. Both DACs then update simultaneously when the SYNC bit is set to 1.
1
0
PD1
PD0
DAC1 Power-Down Bit.
Set to 1 by the user to power up DAC1.
Set to 0 by the user to power down DAC1.
DAC0 Power-Down Bit.
Set to 1 by the user to power up DAC0.
Set to 0 by the user to power down DAC0.
1For correct DAC operation on the 2.5 V to VREF range, the ADC must be powered on.
Rev. A | Page 34 of 72
ADuC814
DACxH/L
Function
SFR Address
DAC0 and DAC1 Data Registers
DAC Data Registers, written by the user to update the DAC outputs.
DAC0L (DAC0 data low byte) –> F9H DAC0H (DAC0 data high byte) –> FAH;
DAC1L (DAC1 data low byte) –> FBH DAC1H (DAC1 data high byte) –> FCH
00H –> Both DAC0 and DAC1 data registers.
Power-On Default
Bit Addressable
No –> Both DAC0 and DAC1 data registers.
The 12-bit DAC data should be written into DACxH/L right-justified such that DACL contains the lower eight bits, and the lower nibble
of DACH contains the upper four bits.
Using the DACs
nonlinearity would be similar, but the upper portion of the
The on-chip DAC architecture consists of a resistor string DAC
transfer function would follow the ideal line right to the end
followed by an output buffer amplifier, the functional equivalent
(VREF in this case, not VDD), showing no signs of upper endpoint
linearity error.
of which is illustrated in Figure 38. Features of this architecture
include inherent guaranteed monotonicity and excellent differ-
ential linearity.
V
DD
V
–50mV
DD
ADuC814
AV
V
–100mV
DD
DD
V
R
R
R
REF
OUTPUT
BUFFER
DAC0
HIGH Z
DISABLE
100mV
(FROM MCU)
50mV
0mV
R
R
FFFH
000H
Figure 39. Endpoint Nonlinearities Due to Amplifier Saturation
The endpoint nonlinearities conceptually illustrated in Figure 39
get worse as a function of output loading. Most ADuC814
specifications assume a 10 kΩ resistive load to ground at the
DAC output. As the output is forced to source or sink more
current, the nonlinear regions at the top or bottom (respectively)
of Figure 39 become larger. With larger current demands, this
can significantly limit output voltage swing. Figure 40 and
Figure 41 illustrate this behavior. Note that the upper trace in
each of these figures is valid only for an output range selection
of 0 V-to-AVDD. In 0 V-to-VREF mode, DAC loading does not
cause high-side voltage drops as long as the reference voltage
remains below the upper trace in the corresponding figure. For
example, if AVDD = 3 V and VREF = 2.5 V, the high-side voltage is
not affected by loads less than 5 mA. But around 7 mA, the
upper curve in Figure 41 drops below 2.5 V (VREF), indicating
Figure 38. Resistor String DAC Functional Equivalent
As illustrated in Figure 38, the reference source for each DAC is
user selectable in software. It can be either AVDD or VREF. In
0 V-to-AVDD mode, the DAC output transfer function spans
from 0 V to the voltage at the AVDD pin. In 0 V-to-VREF mode,
the DAC output transfer function spans from 0 V to the internal
VREF, or if an external reference is applied, the voltage at the VREF
pin. The DAC output buffer features a true rail-to-rail output
stage implementation. This means that, unloaded, each output is
capable of swinging to within less than 100 mV of both AVDD
and ground. Moreover, the DAC’s linearity specification (when
driving a 10 kΩ resistive load to ground) is guaranteed through
the full transfer function except Codes 0 to 48, and, in 0 V-to-
AVDD mode only, Codes 3945 to 4095. Linearity degradation
near ground and VDD is caused by saturation of the output
buffer, and a general representation of its effects (neglecting
offset and gain error) is illustrated in Figure 39. The dotted line
in Figure 39 indicates the ideal transfer function, and the solid
line represents what the transfer function might look like with
endpoint nonlinearities due to saturation of the output buffer.
Note that Figure 39 represents a transfer function in 0 V-to-VDD
mode only. In 0 V-to-VREF mode (with VREF < VDD), the lower
that at these higher currents the output cannot reach VREF
.
Rev. A | Page 35 of 72
ADuC814
5
For larger loads, the current drive capability may not be sufficient.
To increase the source and sink current capability of the DACs,
an external buffer should be added, as shown in Figure 42.
DAC LOADED WITH 0FFFH
4
3
2
1
DAC0
ADuC814
DAC1
DAC LOADED WITH 0000H
10
Figure 42. Buffering the DAC Outputs
0
0
5
15
SOURCE/SINK CURRENT (mA)
The DAC output buffer also features a high impedance disable
function. In the chip’s default power-on state, both DACs are
disabled, and their outputs are in a high impedance state (or
three-state) where they remain inactive until enabled in
software. This means that if a zero output is desired during
power-up or power-down transient conditions, then a pull-
down resistor must be added to each DAC output. Assuming
this resistor is in place, the DAC outputs remain at ground
potential whenever the DAC is disabled.
Figure 40. Source and Sink Current Capability with VREF = VDD = 5 V
4
DAC LOADED WITH 0FFFH
3
1
DAC LOADED WITH 0000H
0
0
5
10
15
SOURCE/SINK CURRENT (mA)
Figure 41. Source and Sink Current Capability with VREF = VDD = 3 V
Rev. A | Page 36 of 72
ADuC814
ON-CHIP PLL
The ADuC814 is intended for use with a 32.768 kHz watch
crystal. An on-board PLL locks onto a multiple (512) of this
32.768kHz frequency to provide a stable 16.777216 MHz clock
for the system. The core can operate at this frequency or at
binary submultiples of it to allow power saving in cases where
maximum core performance is not required. The default core
clock is the PLL clock divided by 8 (2CD = 23) or 2.097152 MHz.
The PLL is controlled via the PLLCON special function register.
PLLCON
SFR Address
Power-On Default
Bit Addressable
PLL Control Register
D7H
03H
No
OSC_PD
LOCK
---
---
FINT
CD2
CD1
CD0
Table 13. PLLCON SFR Bit Designations
Bit No.
Name
Description
7
OSC_PD
Oscillator Power-Down Bit.
Set by the user to halt the 32 kHz oscillator in power-down mode.
Cleared by the user to enable the 32 kHz oscillator in power-down mode. This feature allows the oscillator to
continue clocking the TIC even in power-down mode.
6
LOCK
PLL Lock Bit. This is a read-only bit.
Set automatically at power-on to indicate that the PLL loop is correctly tracking the crystal clock. If the external
crystal becomes subsequently disconnected, the PLL rails and the core halts.
Cleared automatically at power-on to indicate that the PLL is not correctly tracking the crystal clock. This may be due
to the absence of a crystal clock or an external crystal at power-on. In this mode, the PLL output is 16.78 MHz 20%.
5
4
3
---
---
FINT
Reserved. Should be written with 0.
Reserved. Should be written with 0.
Fast Interrupt Response Bit.
Set by the user to enable the response to any interrupt to be executed at the fastest core clock frequency, regardless
of the configuration of the CD2–CD0 bits (see below). Once user code has returned from an interrupt, the core
resumes code execution at the core clock selected by the CD2–CD0 bits.
Cleared by the user to disable the fast interrupt response feature.
CPU (Core Clock) Divider Bits.
This number determines the frequency at which the microcontroller core operates.
2
1
0
CD2
CD1
CD0
CD2
0
CD1
0
CD0
0
Core Clock Frequency (MHz)
16.777216
0
0
1
8.388608
0
1
0
4.194304
0
1
1
2.097152 (Default Core Clock Frequency)
1
1
1
1
0
0
1
1
0
1
0
1
1.048576
0.524288
0.262144
0.131072
Rev. A | Page 37 of 72
ADuC814
TIME INTERVAL COUNTER (TIC)
TCEN
32.768kHz EXTERNAL CRYSTAL
A time interval counter is provided on-chip for counting longer
intervals than the standard 8051 compatible timers are capable
of. The TIC is capable of time-out intervals ranging from 1/128th
second to 255 hours. Furthermore, this counter is clocked by the
crystal oscillator rather than by the PLL and thus has the ability
to remain active in power-down mode and to time long power-
down intervals. This has obvious applications for remote battery-
powered sensors where regular, widely spaced readings are
required.
ITS0, 1
8-BIT
PRESCALER
HUNDREDTHS COUNTER
HTHSEC
INTERVAL
TIMEBASE
SELECTION
MUX
TIEN
SECOND COUNTER
SEC
Six SFRs are associated with the time interval counter, TIMECON
being its control register. Depending on the configuration of the
IT0 and IT1 bits in TIMECON, the selected time counter register
overflow clocks the interval counter. When this counter is equal
to the time interval value loaded in the INTVAL SFR, the TII bit
(TIMECON.2) is set and generates an interrupt if enabled. (See
IEIP2 SFR description under the Interrupt System section.) If
the ADuC814 is in power-down mode, again with TIC interrupt
enabled, the TII bit wakes up the device and resumes code execu-
tion by vectoring directly to the TIC interrupt service vector
address at 0053H. The TIC-related SFRs are described in
Table 14. Note that the time based SFRs can be written initially
with the current time; the TIC can then be controlled and
accessed by the user software. In effect, this facilitates the
implementation of a real-time clock. A block diagram of the
TIC is shown in Figure 43.
MINUTE COUNTER
MIN
HOUR COUNTER
HOUR
8-BIT
INTERVAL COUNTER
COMPARE
COUNT = INTVAL
INTERVAL TIMEOUT
TIME INTERVAL COUNTER INTERRUPT
TIMER INTVAL
INTVAL
Figure 43. Time Interval Counter, Simplified Block Diagram
Rev. A | Page 38 of 72
ADuC814
TIMECON
TIC CONTROL REGISTER
SFR Address
Power-On Default
Bit Addressable
A1H
00H
No
---
TFH
ITS1
ITS0
STI
TII
TIEN
TCEN
Table 14. TIMECON SFR Bit Designations
Bit No.
Name
Description
7
6
---
TFH
Reserved.
Twenty-Four Hour Select Bit.
Set by the user to enable the HOUR counter to count from 0 to 23.
Cleared by the user to enable the HOUR counter to count from 0 to 255.
The time interval counter continues to count after a reset when in hours/min/sec mode. If the part is in 24 hour
mode though, this bit is reset and the part now counts in 255 hour mode. The following code segment can be used
to set the TIC back into 24 hour mode after a RESET event.
MOV
RRC
JNC
ORL
A,TIMECON
;Move contents of TIMECON into ACC
A
;Rotate ACC right by 1 place into Carry
NOTSET
;If CARRY bit is ! = 1 jump to NOTSET, else continue with next line
TIMECON,#01000000B
;If CARRY bit = 1 for last line, then logical OR TIMECON with 40H
;continuation of normal code from here
NOTSE:
ITS1
ITS0
Interval Timebase Selection Bits.
Written by the user to determine the interval counter update rate.
4
3
ITS1
0
0
ITS0
0
1
Interval Timebase
1/128 Second
Seconds
1
0
Minutes
1
1
Hours
STI
Single Time Interval Bit.
Set by the user to generate a single interval timeout. If set, a timeout clears the TIEN bit.
Cleared by the user to allow the interval counter to be automatically reloaded and start counting again at each
interval timeout.
2
1
0
TII
TIC Interrupt Bit.
Set when the 8-bit interval counter matches the value in the INTVAL SFR.
Cleared by the user software.
Time Interval Enable Bit.
Set by the user to enable the 8-bit time interval counter.
Cleared by the user to disable and clear the contents of the interval counter.
Time Clock Enable Bit.
TIEN
TCEN
Set by the user to enable the time clock to the time interval counters.
Cleared by the user to disable the clock to the time interval counters and clear the time interval SFRs.
The time registers (HTHSEC, SEC, MIN and HOUR) can be written while TCEN is low.
Rev. A | Page 39 of 72
ADuC814
INTVAL
User Time Interval Select Register
Function
User code writes the required time interval to this register. When the 8-bit interval counter is equal to the time
interval value loaded in the INTVAL SFR, the TII bit (TIMECON.2) is set and generates an interrupt if enabled.
(See the IEIP2 SFR description in the Interrupt System section.)
SFR Address
A6H
Power-On Default
Bit Addressable
Valid Value
00H
No
0 to 255 decimal
HTHSEC
Hundredths Seconds Time Register
Function
This register is incremented in 1/128 second intervals once TCEN in TIMECON is active. The HTHSEC SFR
counts from 0 to 127 before rolling over to increment the SEC time register.
SFR Address
A2H
Power-On Default
Bit Addressable
Valid Value
00H
No
0 to 127 decimal
SEC
Seconds Time Register
Function
This register is incremented in 1-second intervals once TCEN in TIMECON is active. The SEC SFR counts from
0 to 59 before rolling over to increment the MIN time register.
SFR Address
A3H
Power-On Default
Bit Addressable
Valid Value
00H
No
0 to 59 decimal
MIN
Minutes Time Register
Function
This register is incremented in 1-minute intervals once TCEN in TIMECON is active. The MIN SFR counts
from 0 to 59 before rolling over to increment the HOUR time register.
SFR Address
A4H
Power-On Default
Bit Addressable
Valid Value
00H
No
0 to 59 decimal
HOUR
Hours Time Register
Function
This register is incremented in 1-hour intervals once TCEN in TIMECON is active. If the TFH bit (TIMECON.6)
is set to 1 the HOUR SFR counts from 0 to 23 before rolling over to 0. If the TFH bit is set to 0, the HOUR SFR
counts from 0 to 255 before rolling over to 0.
SFR Address
A5H
Power-On Default
Bit Addressable
Valid Value
00H
No
0 to 23 decimal
Rev. A | Page 40 of 72
ADuC814
WATCHDOG TIMER
in WDCON. Full control and status of the watchdog timer
The purpose of the watchdog timer is to generate a device reset
or interrupt within a reasonable amount of time if the ADuC814
enters an erroneous state, possibly due to a programming error,
electrical noise, or RFI. The watchdog function can be disabled
by clearing the WDE (watchdog enable) bit in the watchdog
control (WDCON) SFR. When enabled, the watchdog circuit
generates a system reset or interrupt (WDS) if the user program
fails to set the watchdog (WDE) bit within a predetermined
amount of time (see PRE3–0 bits in WDCON). The watchdog
timer itself is a 16-bit counter that is clocked at 32.768 kHz. The
watchdog timeout interval can be adjusted via the PRE3–0 bits
function can be controlled via the watchdog timer control SFR
(WDCON). The WDCON SFR can be written only by the user
software if the double write sequence (WDWR) described in
Table 15 is initiated on every write access to the WDCON SFR.
WDCON
Watchdog Timer Control Register
SFR Address
Power-On Default
Bit Addressable
C0H
10H
Yes
PRE3
PRE2
PRE1
PRE0
WDIR
WDS
WDE
WDWR
Table 15. WDCON SFR Bit Designation
Bit No.
Name
PRE3
PRE2
PRE1
Description
7
6
5
Watchdog Timer Prescale Bits.
The watchdog timeout period is given by the equation
WD = (2PRE × (29/fPLL))
where fPLL = 32.768 kHz and PRE is defined as follows:
t
4
PRE0
PRE3
PRE2
PRE1
PRE0
Timeout Period (ms)
Action
0
0
0
0
0
0
0
0
1
0
0
0
0
1
1
1
1
0
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
15.6
31.2
62.5
125
250
500
1000
2000
0.0
Reset or Interrupt
Reset or Interrupt
Reset or Interrupt
Reset or Interrupt
Reset or Interrupt
Reset or Interrupt
Reset or Interrupt
Reset or Interrupt
Immediate Reset
PRE3–0 > 1001
Reserved
3
WDIR
Watchdog Interrupt Request.
If this bit is set by the user, the watchdog generates an interrupt response instead of a system reset when the
watchdog timeout period has expired. This interrupt is not disabled by the CLR EA instruction and it is also a fixed,
high-priority interrupt.
If the watchdog is not being used to monitor the system, it can alternatively be used as a timer. The prescaler is used
to set the timeout period in which an interrupt is generated. (See Table 33, Note 1, in the Interrupt System section.)
2
1
WDS
WDE
Watchdog Status Bit.
Set by the watchdog controller to indicate that a watchdog timeout has occurred.
Cleared by writing a 0 or by an external hardware reset. It is not cleared by a watchdog reset.
Watchdog Enable Bit.
Set by the user to enable the watchdog and clear its counters. If this bit is not set by the user within the watchdog
timeout period, the watchdog generates a reset or interrupt, depending on WDIR.
Cleared under the following conditions: User writes 0, Watchdog Reset (WDIR = 0); Hardware Reset; PSM Interrupt.
Watchdog Write Enable Bit.
0
WDWR
To write data into the WDCON SFR involves a double instruction sequence. The WDWR bit must be set and followed
immediately by a write instruction to the WDCON SFR. For example:
CLR EA
SETB WDWR
; disable interrupts while writing to WDT
; allow write to WDCON
MOV WDCON, #72H ; enable WDT for 2.0s timeout
SET B EA
; enable interrupts again (if rqd)
Rev. A | Page 41 of 72
ADuC814
POWER SUPPLY MONITOR
As its name suggests, the power supply monitor, once enabled,
monitors the supply (DVDD) on the ADuC814. It indicates when
any of the supply pins drop below one of four user-selectable
voltage trip points from 2.63 V to 4.63 V. For correct operation
of the power supply monitor function, DVDD must be equal to
or greater than 2.7 V. Monitor function is controlled via the
PSMCON SFR. If enabled via the IEIP2 SFR, the monitor
interrupts the core using the PSMI bit in the PSMCON SFR.
This bit is not cleared until the failing power supply has
returned above the trip point for at least 250 ms. This monitor
function allows the user to save working registers to avoid
possible data loss due to the low supply condition, and also
ensures that normal code execution does not resume until a safe
supply level is well established. The supply monitor is also
protected against spurious glitches triggering the interrupt
circuit.
PSMCON
Power Supply Monitor Control Register
SFR Address
Power-On Default
Bit Addressable
DFH
DEH
No
----
CMPD
PSMI
TPD1
TPD0
----
----
PSMEN
Table 16. PSMCON SFR Bit Designations
Bit No.
Name
Description
7
6
PSMCON.7
CMPD
Reserved.
DVDD Comparator Bit.
This is a read-only bit and directly reflects the state of the DVDD comparator.
Read 1 indicates that the DVDD supply is above its selected trip point.
Read 0 indicates that the DVDD supply is below its selected trip point.
Power Supply Monitor Interrupt Bit.
5
PSMI
This bit is set high by the MicroConverter if CMPD is low, indicating low digital supply. The PSMI bit can be used to
interrupt the processor. Once CMPD returns and remains high, a 250 ms counter is started. When this counter
times out, the PSMI interrupt is cleared. PSMI can also be written by the user; however, if the comparator output is
low, it is not possible for the user to clear PSMI.
4
3
TPD1
TPD0
DVDD Trip Point Selection Bits.
These bits select the DVDD trip-point voltage as follows:
TPD1
TPD0
Selected DVDD Trip Point (V)
0
0
1
1
0
1
0
1
4.63
3.08
2.93
2.63
2
1
0
PSMCON.2
PSMCON.1
PSMEN
Reserved.
Reserved.
Power Supply Monitor Enable Bit.
Set to 1 by the user to enable the power supply monitor circuit.
Cleared to 0 by the user to disable the power supply monitor circuit.
Rev. A | Page 42 of 72
ADuC814
ADuC814 CONFIGURATION REGISTER (CFG814)
External Clock
The ADuC814 is housed in a 28-lead TSSOP package. To
maintain as much functional compatibility with other
The ADuC814 is intended for use with a 32.768 kHz watch
crystal. The on-chip PLL locks onto a multiple of this to provide
a stable 16.777216 MHz clock for the device. On the ADuC814,
P3.5 alternate functions include T1 input and slave select in SPI
master mode. P3.5 also functions as external clock input, EXTCLK,
selected via Bit 1 of the CFG814 SFR. When selected, this
external clock bypasses the PLL and is used as the clock for the
device, therefore allowing the ADuC814 to be synchronized to
the rest of the application system. The maximum input frequency
of this external clock is 16.777216 MHz. If selected, the EXTCLK
signal affects the timing of the majority of peripherals on the
ADuC814 including the ADC, EEPROM controller, watchdog
timer, SPI interface clock, and the MicroConverter core clock.
MicroConverter products, some pins share multiple I/O
functionality. Switching between these functions is controlled
via the ADuC814 configuration SFR, CFG814, located at SFR
address 9CH. A summary of these functions is described and a
detailed bit designation for the CFG814 SFR is given in Table 17.
Serial Peripheral Interface
The SPI interface on the ADuC814 shares the same pins as
digital outputs P3.5, P3.6, and P3.7. The SPE bit in SPICON is
used to select which interface is active at any one time. This is
described in greater detail in the next section. By default, these
pins operate as standard Port 3 pins. Bit 0 of the CFG814 SFR
must be set to 1 to enable the SPI interface on these Port 3 pins.
CFG814
ADuC814 Configuration Register
SFR Address
Power-On Default
Bit Addressable
9CH
04H
No
EXTCLK
SER_EN
Table 17. CFG814 SFR Bit Designations
Bit No.
Name
Description
1
EXTCLK
External Clock Selection Bit.
Set to 1 to enable EXTCLK as MCU core clock.
Cleared to 0 to enable XTAL and PLL as the MCU core clock.
Serial Interface Enable Bit.
0
SER_EN
Set to 1 by the user to enable the SPI interface onto the P3.5, P3.6, and P3.7 pins.
Cleared to 0 by the user to enable standard Port 3 functionality on the P3.5, P3.6, and P3.7 pins.
Rev. A | Page 43 of 72
ADuC814
SERIAL PERIPHERAL INTERFACE
eight SCLOCK periods. The SCLOCK pin is configured as an
output in master mode and as an input in slave mode.
The ADuC814 integrates a complete hardware serial peripheral
interface (SPI) on-chip. SPI is an industry-standard synchronous
serial interface that allows eight bits of data to be synchronously
transmitted and received simultaneously, i.e., full duplex. Note
that the SPI pins MISO and MOSI are multiplexed with digital
outputs P3.6 and P3.7. These pins are controlled via the CFG814.0
bit in the CFG814 SFR (Table 17), which configures the relevant
Port 3 pins for normal operation or serial port operation. When
the relevant Port 3 pins are configured for serial interface operation
via the CFG814 SFR, the SPE bit in the SPICON SFR configures
SPI or I2C operation (see SPE bit description in Table 18). SPI
can be configured for master or slave operation, and typically
consists of four pins described next.
In master mode, the bit rate, polarity, and phase of the clock are
controlled by the CPOL, CPHA, SPR0, and SPR1 bits in the
SPICON SFR (see Table 18). In slave mode, the SPICON register
must be configured with the phase and polarity (CPHA and
CPOL) of the expected input clock. In both master and slave
modes, the data is transmitted on one edge of the SCLOCK
signal and sampled on the other. It is important, therefore, that
the CPHA and CPOL are configured the same for the master
and slave devices.
SS
(Slave Select Input Pin)
SS
The input pin (Pin 22) is used only when the ADuC814 is
configured in slave mode to enable the SPI peripheral. This line
is active low. Data is received or transmitted in slave mode only
MISO (Master In, Slave Out Data I/O Pin)
The MISO pin (Pin 23) is configured as an input line in master
mode and as an output line in slave mode. The MISO line on
the master (data in) should be connected to the MISO line in
the slave device (data out). The data is transferred as byte-wide
(8-bit) serial data, MSB first.
SS
when the pin is low, allowing the ADuC814 to be used in
single master, multislave SPI configurations. If CPHA = 1, then
SS
the input may be permanently pulled low. With CPHA = 0,
SS
the input must be driven low before the first bit in a byte-
MOSI (Master Out, Slave In Pin)
wide transmission or reception and return high again after the
last bit in that byte-wide transmission or reception. In SPI slave
The MOSI pin (Pin 24) is configured as an output line in master
mode and as an input line in slave mode. The MOSI line on the
master (data out) should be connected to the MOSI line in the
slave device (data in). The data is transferred as byte-wide (8-bit)
serial data, MSB first.
SS
mode, the logic level on the external pin can be read via the
SPR0 bit in the SPICON SFR.
The following SFR registers are used to control the SPI interface.
SCLOCK (Serial Clock I/O Pin)
SPICON
SPI Control Register
SFR Address
Power-On Default
Bit Addressable
F8H
04H
Yes
The SCLOCK pin (Pin 25) is used to synchronize the data being
transmitted and received through the MOSI and MISO data
lines. A single data bit is transmitted and received in each
SCLOCK period. Therefore, a byte is transmitted/received after
ISPI
WCOL
SPE
SPM
CPOL
CPHA
SPR1
SPR0
Table 18. SPICON SFR Bit Designations
Bit No.
Name
Description
7
ISPI
SPI Interrupt Bit.
Set by the MicroConverter at the end of each SPI transfer.
Cleared directly by the user code or indirectly by reading the SPIDAT SFR.
Write Collision Error Bit.
Set by the MicroConverter if SPIDAT is written to while an SPI transfer is in progress.
Cleared by the user.
SPI Interface Enable Bit.
Set by the user to enable the SPI interface.
Cleared by the user to enable the I2C interface.
6
5
4
3
WCOL
SPE
SPIM
CPOL1
SPI Master/Slave Mode Select Bit.
Set by the user to enable master mode operation (SCLOCK is an output).
Cleared by the user to enable slave mode operation (SCLOCK is an input).
Clock Polarity Select Bit.
Set by the user if SCLOCK idles high. Cleared by the user if SCLOCK idles low.
Rev. A | Page 44 of 72
ADuC814
Bit No.
Name
CPHA1
Description
2
Clock Phase Select Bit.
Set by the user if the leading SCLOCK edge is to transmit data.
Cleared by the user if the trailing SCLOCK edge is to transmit data.
SPI Bit Rate Select Bits.
1
0
SPR1
SPR0
These bits select the SCLOCK rate (bit rate) in master mode as follows:
SPR1
SPR0
Selected Bit Rate
0
0
1
1
0
1
0
1
f
f
f
CORE/2
CORE/4
CORE/8
fcore/16
In SPI slave mode,where SPIM = 0, the logic level on the external SS pin (Pin 22), can be read via the SPR0 bit.
1The CPOL and CPHA bits should both contain the same values for master and slave devices.
SPIDAT
SPI Data Register
Function
The SPIDAT SFR is written by the user to transmit data over the SPI interface or read by the user code to read
data just received by the SPI interface.
SFR Address
Power-On Default
Bit Addressable
F7H
00H
No
Using the SPI Interface
SPI Interface—Master Mode
Depending on the configuration of the bits in the SPICON SFR
shown in Table 18, the ADuC814 SPI interface transmits or
receives data in a number of possible modes. Figure 44 shows all
possible ADuC814 SPI configurations and the timing relation-
ships and synchronization between the signals involved.
In master mode, the SCLOCK pin is always an output and
generates a burst of eight clocks whenever user code writes to
the SPIDAT register. The SCLOCK bit rate is determined by
SPR0 and SPR1 in SPICON. It should also be noted that the
pin is not used in master mode. If the ADuC814 needs to assert
SS
SCLOCK
(CP0L = 1)
SS
the pin on an external slave device, a port digital output pin
should be used. In master mode, a byte transmission or reception
is initiated by a write to SPIDAT. Eight clock periods are gener-
ated via the SCLOCK pin and the SPIDAT byte being transmitted
via MOSI. With each SCLOCK period, a data bit is also sampled
via MISO. After eight clocks, the byte is completely transmitted,
and the input byte is waiting in the input shift register. The ISPI
flag is set automatically and an interrupt occurs if enabled. The
value in the shift register is latched into SPIDAT.
SCLOCK
(CP0L = 0)
SS
SAMPLE INPUT
?
MSB BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB
DATA OUTPUT
(CPHA = 1)
ISPI FLAG
SPI Interface—Slave Mode
SAMPLE INPUT
DATA OUTPUT
SS
In slave mode, the SCLOCK is an input. The pin must also be
?
MSB BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB
driven low externally during the byte communication. Trans-
mission is also initiated by a write to SPIDAT. In slave mode, a
data bit is transmitted via MISO, and a data bit is received via
MOSI on each input SCLOCK. After eight clocks, the byte is
completely transmitted and the input byte is waiting in the
input shift register. The ISPI flag is set automatically and an
interrupt occurs if enabled. The value in the shift register is
latched into SPIDAT only when the transmission/reception of a
byte is complete. The end of transmission occurs after the
(CPHA = 0)
ISPI FLAG
Figure 44. ADuC814, SPI Timing, All Modes
SS
eighth clock is received, if CPHA = 1, or when returns high if
CPHA = 0.
Rev. A | Page 45 of 72
ADuC814
I2C COMPATIBLE INTERFACE
The ADuC814 supports a 2-wire serial interface mode that is
I2C compatible. The I2C compatible interface shares its pins with
the on-chip SPI interface, and therefore the user can enable only
one interface or the other at any given time (see the SPE bit in
SPICON SFR, Table 18). Application Note uC001 describes the
operation of this interface as implemented, and is available on
the MicroConverter website at www.analog.com/microconverter.
This interface can be configured as a software master or hard-
ware slave, and uses two pins in the interface.
SDATA (Pin 24)
Serial Data I/O
SCLOCK (Pin 25) Serial Clock
Three SFRs are used to control the I2C compatible interface.
I2CCON
SFR Address
Power-On Default
Bit Addressable
I2C Control Register
E8H
00H
Yes
MDO
MDE
MCO
MDI
I2CM
I2CRS
I2CTX
I2CI
Table 19. I2CCON SFR Bit Designations
Bit No.
Name
MDO
Description
I2C Software Master Data Output Bit (Master Mode Only).
7
This data bit is used to implement a master I2C transmitter interface in software. Data written to this bit is output on
the SDATA pin if the data output enable (MDE) bit is set.
I2C Software Master Data Output Enable Bit (Master Mode Only).
Set by the user to enable the SDATA pin as an output (Tx).
Cleared by the user to enable SDATA pin as an input (Rx).
I2C Software Master Clock Output Bit (Master Mode Only).
This data bit is used to implement a master I2C transmitter interface in software. Data written to this bit is output on
the SCLOCK pin.
MDE
MCO
MDI
6
5
4
3
2
1
0
I2C Software Master Data Input Bit (Master Mode Only).
This data bit is used to implement a master I2C receiver interface in software. Data on the SDATA pin is latched into
this bit on SCLOCK if the data output enable (MDE) bit is 0.
I2C Master/Slave Mode Bit.
I2CM
I2CRS
I2CTX
I2CI
Set by the user to enable I2C software master mode.
Cleared by the user to enable I2C hardware slave mode.
I2C Reset Bit (Slave Mode Only).
Set by the user to reset the I2C interface.
Cleared by the user code for normal I2C operation.
I2C Direction Transfer Bit (Slave Mode Only).
Set by the MicroConverter if the interface is transmitting.
Cleared by the MicroConverter if the interface is receiving.
I2C Interrupt Bit (Slave Mode Only).
Set by the MicroConverter after a byte has been transmitted or received.
Cleared automatically when user code reads the I2CDAT SFR (see the I2CDAT SFR description that follows).
I2CADD
Function
I2C Address Register
Holds the I2C peripheral address for the part. It may be overwritten by the user code. Application Note uC001 at
www.analog.com/microconverter describes the format of the 7-bit address in detail.
SFR Address
Power-On Default
Bit Addressable
9BH
55H
No
I2CDAT
Function
I2C Data Register
The I2CDAT SFR is written to by the user code to transmit data over the I2C interface, or it is read by the user
code to read data just received via the I2C interface. Accessing the I2CDAT register automatically clears any
pending I2C interrupts and the I2CI bit in the I2CCON SFR.
SFR Address
Power-On Default
Bit Addressable
9AH
00H
No
Rev. A | Page 46 of 72
ADuC814
8051 COMPATIBLE ON-CHIP PERIPHERALS
pins. By default (power-on) these pins are configured as analog
inputs, that is, 1 written in the corresponding Port 1 register bit.
To configure any of these pins as digital inputs, the user should
write a 0 to these port bits to configure the corresponding pin as
a high impedance digital input.
This section gives a brief overview of the various secondary
peripheral circuits that are available to the user on-chip. These
functions are fully 8051 compatible and are controlled via
standard 8051 SFR bit definitions.
Parallel I/O Ports 1 and 3
Port 3 is a bidirectional port with internal pull-ups directly con-
trolled via the P3 SFR (SFR address = B0H). Port 3 pins that
have 1s written to them are pulled high by the internal pull-ups
and in that state, they can be used as inputs. As inputs, Port 3
pins being pulled externally low sources current because of the
internal pull-ups. Port 3 pins also have various secondary
functions described in Table 21.
The ADuC814 has two input/output ports. In addition to per-
forming general-purpose I/O, some ports are multiplexed with
an alternate function for the peripheral features on the device.
In general, when a peripheral is enabled, that pin may not be
used as a general purpose I/O pin.
Port 1 is an 8-bit port directly controlled via the P1 SFR (SFR
address = 90H). The Port 1 pins are divided into two distinct
pin groupings.
Table 21. Port 3, Alternate Pin Functions
Pin No.
Alternate Function
P3.0
RxD (UART Input Pin)
(or Serial Data I/O in Mode 0)
TxD (UART Output Pin)
(or Serial Clock Output in Mode 0)
INT0 (External Interrupt 0)
INT1 (External Interrupt 1)
T0 (Timer/Counter 0 External Input)
T1 (Timer/Counter 1 External Input)
P1.0 and P1.1 pins on Port 1 are bidirectional digital I/O pins
with internal pull-ups. If P1.0 and P1.1 have 1s written to them
via the P1 SFR, these pins are pulled high by the internal pull-
up resistors. In this state they can also be used as inputs. As
input pins being externally pulled low, they source current
because of the internal pull-ups. With 0s written to them, both
of these pins drive a logic low output voltage (VOL) and are
capable of sinking 10 mA compared to the standard 1.6 mA
sink capability on the other port pins. These pins also have
various secondary functions described in Table 20.
P3.1
P3.2
P3.3
P3.4
P3.5
SS
(Slave Select in SPI Slave Mode)
P3.6
P3.7
MISO (Master in Slave Out in SPI Mode)
MOSI (Master Out Slave In in SPI Mode)
Table 20. Port 1, Alternate Pin Functions
Pin No.
Alternate Function
P1.0
P1.1
T2 (Timer/Counter 2 External Input)
T2EX (Timer/Counter 2 Capture/Reload Trigger)
Additional Digital Outputs Pins
Pins P1.0 and P1.1 can be used to provide high current (10 mA
sink) general-purpose I/O.
The remaining Port 1 pins (P1.2–P1.7) can be configured only
as analog input (ADC), analog output (DAC) or digital input
Rev. A | Page 47 of 72
ADuC814
TIMERS/COUNTERS
following the one in which the transition was detected. Since it
takes two machine cycles (16 core clock periods) to recognize a
1-to-0 transition, the maximum count rate is 1/16 of the core
clock frequency. There are no restrictions on the duty cycle of
the external input signal, but to ensure that a given level is
sampled at least once before it changes, it must be held for a
minimum of one full machine cycle. Remember that the core
clock frequency is programmed via the CD0–CD2 selection bits
in the PLLCON SFR. User configuration and control of all timer
operating modes is achieved via three SFRs: TMOD, TCON,
and T2CON.
The ADuC814 has three 16-bit timer/counters: Timer 0,
Timer 1, and Timer 2. The timer/counter hardware has been
included on-chip to relieve the processor core of the overhead
inherent in implementing timer/counter functionality in
software. Each timer/counter consists of two 8-bit registers,
THx and TLx (x = 0, 1 and 2). All three can be configured to
operate either as timers or event counters.
In timer function, the TLx register is incremented every
machine cycle. Thus one can think of it as counting machine
cycles. Since a machine cycle consists of 12 core clock periods,
the maximum count rate is 1/12 of the core clock frequency.
In counter function, the TLx register is incremented by a 1-to-0
transition at its corresponding external input pin, T0, T1, or T2.
In this function, the external input is sampled during S5P2 of
every machine cycle. When the samples show a high in one
cycle and a low in the next cycle, the count is incremented. The
new count value appears in the register during S3P1 of the cycle
TMOD
Timer/Counter 0 and 1 Mode Register
SFR Address
Power-On Default
Bit Addressable
89H
00H
No
GATE
C/T
M1
M0
GATE
C/T
M1
M0
Table 22. TMOD SFR Bit Designations
Bit Name Description
7
GATE
Timer 1 Gating Control.
Set by software to enable Timer/Counter 1 only while INT1 pin is high and TR1 control bit is set.
Cleared by software to enable Timer 1 whenever TR1 control bit is set.
Timer 1 Timer or Counter Select Bit.
6
C/T
Set by software to select counter operation (input from T1 pin).
Cleared by software to select timer operation (input from internal system clock).
Timer 1 Mode Select Bit 1 (Used with M0 Bit).
5
4
M1
M0
Timer 1 Mode Select Bit 0.
M1 M0
0
0
1
1
0
1
0
1
TH1 operates as an 8-bit timer/counter. TL1 serves as 5-bit prescaler.
16-Bit Timer/Counter. TH1 and TL1 are cascaded; there is no prescaler.
8-Bit Auto-Reload Timer/Counter. TH1 holds a value which is to be reloaded into TL1 each time it overflows.
Timer/Counter 1 Stopped.
3
2
Gate
Timer 0 Gating Control.
Set by software to enable Timer/Counter 0 only while INT0 pin is high and the TR0 control bit is set.
Cleared by software to enable Timer 0 whenever the TR0 control bit is set.
Timer 0 Timer or Counter Select Bit.
T
C/
Set by software to select counter operation (input from T0 pin).
Cleared by software to select timer operation (input from internal system clock).
Timer 0 Mode Select Bit 1.
1
0
M1
M0
Timer 0 Mode Select Bit 0.
M1 M0
0
0
1
1
0
1
0
1
TH0 operates as an 8-bit timer/counter. TL0 serves as 5-bit prescaler.
16-Bit Timer/Counter. TH0 and TL0 are cascaded; there is no prescaler.
8-Bit Autoreload Timer/Counter. TH0 holds a value which is to be reloaded into TL0 each time it overflows.
TL0 is an 8-bit timer/counter controlled by the standard Timer 0 control bits.
Rev. A | Page 48 of 72
ADuC814
TCON
Timer/Counter 0 and 1 Control Register
SFR Address
Power-On Default
Bit Addressable
88H
00H
Yes
TF1
TR1
TF0
TR0
IE11
IT11
IE0
IT01
1
INT0
INT1
interrupt pins.
These bits are not used in the control of Timer/Counter 0 and 1, but are used instead in the control and monitoring of the external
and
Table 23. TCON SFR Bit Designations
Bit No.
Name
Description
7
TF1
Timer 1 Overflow Flag.
Set by hardware on a Timer/Counter 1 overflow.
Cleared by hardware when the program counter (PC) vectors to the interrupt service routine.
Timer 1 Run Control Bit.
Set by the user to turn on Timer/Counter 1.
Cleared by the user to turn off Timer/Counter 1.
Timer 0 Overflow Flag.
Set by hardware on a Timer/Counter 0 overflow.
Cleared by hardware when the PC vectors to the interrupt service routine.
Timer 0 Run Control Bit.
Set by the user to turn on Timer/Counter 0.
Cleared by the user to turn off Timer/Counter 0.
External Interrupt 1 (INT1) Flag.
6
5
4
3
TR1
TF0
TR0
IE1
INT1
, depending on bit IT1
Set by hardware by a falling edge or zero level being applied to external interrupt pin
state.
Cleared by hardware when the when the PC vectors to the interrupt service routine only if the interrupt was
transition-activated. If level-activated, the external requesting source controls the request flag, rather than the on-
chip hardware.
2
1
IT1
IE0
External Interrupt 1 (IE1) Trigger Type.
Set by software to specify edge-sensitive detection, that is, 1-to-0 transition.
Cleared by software to specify level-sensitive detection, that is, zero level.
External Interrupt 0 (INT0) Flag.
Set by hardware by a falling edge or zero level being applied to external interrupt pin INT0, depending on bit IT0
state.
Cleared by hardware when the PC vectors to the interrupt service routine, but only if the interrupt was transition-
activated. If level-activated, the external requesting source controls the request flag, rather than the on-chip
hardware.
0
IT0
External Interrupt 0 (IE0) Trigger Type.
Set by software to specify edge-sensitive detection, that is, 1-to-0 transition.
Cleared by software to specify level-sensitive detection, that is, zero level.
Timer/Counter 0 and 1 Data Registers
Each timer consists of two 8-bit registers. These can be used as independent registers or combined to be a single 16-bit register, depending
on the timer mode configuration.
TH0 and TL0
SFR Address
Timer 0 high byte and low byte.
8CH, 8AH, respectively
TH1 and TL1
SFR Address
Timer 1 high byte and low byte.
8DH, 8BH, respectively
Rev. A | Page 49 of 72
ADuC814
Mode 2 (8-Bit Timer/Counter with Autoreload)
TIMER/COUNTER 0 AND 1 OPERATING MODES
Mode 2 configures the timer register as an 8-bit counter (TL0)
with automatic reload, as shown in Figure 47. Overflow from TL0
not only sets TF0, but also reloads TL0 with the contents of TH0,
which is preset by software. The reload leaves TH0 unchanged.
The following paragraphs describe the operating modes for
Timer/Counters 0 and 1. Unless otherwise noted, it should be
assumed that these modes of operation are the same for both
Timer 0 and Timer 1.
Mode 0 (13-Bit Timer/Counter)
CORE
÷12
CLK*
Mode 0 configures an 8-bit timer/counter with a divide-by-32
prescaler. Figure 45 shows Mode 0 operation.
C/T = 0
INTERRUPT
TL0
TF0
(8 BITS)
C/T = 1
CORE
÷12
CLK*
P3.4/T0
CONTROL
TR0
C/T = 0
INTERRUPT
TL0
TL0
TF0
(5 BITS) (8 BITS)
C/T = 1
RELOAD
TL0
P3.4/T0
GATE
CONTROL
(8 BITS)
P3.2/INT0
TR0
*THE CORE CLOCK IS THE OUTPUT OF THE PLL
GATE
Figure 47. Timer/Counter 0, Mode 2
P3.2/INT0
*THE CORE CLOCK IS THE OUTPUT OF THE PLL
Mode 3 (Two 8-Bit Timer/Counters)
Figure 45. Timer/Counter 0, Mode 0
Mode 3 has different effects on Timer 0 and Timer 1. Timer 1 in
Mode 3 simply holds its count. The effect is the same as setting
TR1 = 0. Timer 0 in Mode 3 establishes TL0 and TH0 as two
separate counters. This configuration is shown in Figure 48. TL0
In this mode, the timer register is configured as a 13-bit register.
As the count rolls over from all 1s to all 0s, it sets the timer
overflow flag TF0. The overflow flag, TF0, can then be used to
request an interrupt. The counted input is enabled to the timer
INT0
uses the Timer 0 control bits: C/T, GATE, TR0,
, and TF0.
INT0
when TR0 = 1 and either Gate = 0 or
= 1.
TH0 is locked into a timer function (counting machine cycles)
and takes over the use of TR1 and TF1 from Timer 1. Thus, TH0
controls the Timer 1 interrupt. Mode 3 is provided for applica-
tions requiring an extra 8-bit timer or counter. When Timer 0 is
in Mode 3, Timer 1 can be turned on and off by switching it out
of, and into, its own Mode 3, or can still be used by the serial
interface as a baud rate generator. In fact, it can be used in any
application not requiring an interrupt from Timer 1 itself.
Setting Gate = 1 allows the timer to be controlled by external
INT0
input
to facilitate pulse width measurements. TR0 is a
control bit in the special function register TCON; Gate is in
TMOD. The 13-bit register consists of all eight bits of TH0 and
the lower five bits of TL0. The upper three bits of TL0 are
indeterminate and should be ignored. Setting the run flag (TR0)
does not clear the registers.
CORE
CLK*
CORE
CLK/12
Mode 1 (16-Bit Timer/Counter)
÷12
Mode 1 is the same as Mode 0, except that the timer register is
running with all 16 bits. Mode 1 is shown in Figure 46.
C/T = 0
C/T = 1
INTERRUPT
TL0
(8 BITS)
TF0
P3.4/T0
CORE
÷12
CLK*
CONTROL
C/T = 0
TR0
INTERRUPT
TL0
TL0
TF0
(8 BITS) (8 BITS)
C/T = 1
GATE
P3.4/T0
P3.2/INT0
CONTROL
TR0
INTERRUPT
TL0
(8 BITS)
CORE
CLK/12
TF1
GATE
P3.2/INT0
TR1
*THE CORE CLOCK IS THE OUTPUT OF THE PLL
*THE CORE CLOCK IS THE OUTPUT OF THE PLL
Figure 46. Timer/Counter 0, Mode 1
Figure 48. Timer/Counter 0, Mode 3
Rev. A | Page 50 of 72
ADuC814
T2CON
Timer/Counter 2 Control Register
SFR Address
Power-On Default
Bit Addressable
C8H
00H
Yes
TF2
EXF2
RCLK
TCLK
EXEN2
TR2
CNT2
CAP2
Table 24. T2CON SFR Bit Designations
Bit No.
Name Description
7
TF2
Timer 2 Overflow Flag.
Set by hardware on a Timer 2 overflow. TF2 is not set when either RCLK or TCLK = 1.
Cleared by the user software.
6
5
4
3
EXF2
RCLK
TCLK
Timer 2 External Flag.
Set by hardware when either a capture or reload is caused by a negative transition on T2EX and EXEN2 = 1.
Cleared by the user software.
Receive Clock Enable.
Set by the user to enable the serial port to use Timer 2 overflow pulses for its receive clock in serial port in Modes 1 and 3.
Cleared by the user to enable Timer 1 overflow to be used for the receive clock.
Transmit Clock Enable Bit.
Set by the user to enable the serial port to use Timer 2 overflow pulses for its transmit clock in serial port Modes 1 and 3.
Cleared by the user to enable Timer 1 overflow to be used for the transmit clock.
EXEN2 Timer 2 External Enable Flag.
Set by the user to enable a capture or reload to occur as a result of a negative transition on T2EX if Timer 2 is not being
used to clock the serial port.
Cleared by the user for Timer 2 to ignore events at T2EX.
Timer 2 Start/Stop Control Bit.
Set by the user to start Timer 2.
Cleared by the user to stop Timer 2.
Timer 2 timer or counter function select bit.
Set by the user to select counter function (input from external T2 pin).
Cleared by the user to select timer function (input from on-chip core clock).
Timer 2 Capture/Reload Select Bit.
2
1
0
TR2
CNT2
CAP2
Set by the user to enable captures on negative transitions at T2EX if EXEN2 = 1.
Cleared by the user to enable autoreloads with Timer 2 overflows or negative transitions at T2EX when EXEN2 = 1.
When either RCLK = 1 or TCLK = 1, this bit is ignored and the timer is forced to autoreload on Timer 2 overflow.
Timer/Counter 2 Data Registers
Timer/Counter 2 also has two pairs of 8-bit data registers associated with it. These are used as both timer data registers and timer
capture/reload registers.
TH2 and TL2
SFR Address
Timer 2, data high byte and low byte.
CDH, CCH, respectively
RCAP2H and RCAP2L
SFR Address
Timer 2, Capture/Reload byte and low byte.
CBH, CAH, respectively
Rev. A | Page 51 of 72
ADuC814
TIMER/COUNTER 2 OPERATING MODES
16-Bit Capture Mode
This section describes the operating modes for Timer/Counter
2. The operating modes are selected by bits in the T2CON SFR
as shown in Table 27.
In the capture mode, there are again two options that are
selected by bit EXEN2 in T2CON. If EXEN2 = 0, then Timer 2
is a 16-bit timer or counter which, upon overflowing, sets bit
TF2, the Timer 2 overflow bit, which can be used to generate an
interrupt. If EXEN2 = 1, then Timer 2 still performs the above,
but a 1-to-0 transition on external input T2EX causes the cur-
rent value in the Timer 2 registers, TL2 and TH2, to be captured
into registers RCAP2L and RCAP2H, respectively. In addition,
the transition at T2EX causes bit EXF2 in T2CON to be set, and
EXF2, like TF2, can generate an interrupt. Capture mode is
illustrated in Figure 50.
Table 25. Mode Selection in T2CON
RCLK (or) TCLK
CAP2
TR2
MODE
0
0
1
X
0
1
X
X
1
1
1
0
16-Bit Autoreload
16-Bit Capture
Baud Rate
OFF
16-Bit Autoreload Mode
In autoreload mode, there are two options that are selected by
bit EXEN2 in T2CON. If EXEN2 = 0, then when Timer 2 rolls
over, it not only sets TF2 but also causes the Timer 2 registers to
be reloaded with the 16-bit value in registers RCAP2L and
RCAP2H, which are preset by software. If EXEN2 = 1, then
Timer 2 still performs the above, but with the added feature that
a 1-to-0 transition at external input T2EX also triggers the
16-bit reload and sets EXF2. The autoreload mode is illustrated
in Figure 49.
The baud rate generator mode is selected by RCLK = 1 and/or
TCLK = 1. In either case, if Timer 2 is being used to generate
the baud rate, the TF2 interrupt flag does not occur. Therefore
Timer 2 interrupts do not occur so they do not have to be
disabled. In this mode, the EXF2 flag, however, can still cause
interrupts; this can be used as a third external interrupt. Baud
rate generation is described as part of the UART Serial Interface
section that follows.
CORE
÷12
CLK*
C/T2 = 0
C/T2 = 1
TL2
TL2
(8 BITS)
(8 BITS)
T2
CONTROL
TR2
PIN
CAPTURE
TRANSITION
DETECTOR
RCAP2L
RCAP2H
TF2
TIMER
INTERRUPT
EXF2
T2EX
PIN
CONTROL
EXEN2
*THE CORE CLOCK IS THE OUTPUT OF THE PLL
Figure 49. Timer/Counter 2, 16-Bit Autoreload Mode
CORE
CLK*
÷12
C/T2 = 0
C/T2 = 1
TL2
(8 BITS)
TL2
(8 BITS)
TF2
T2
CONTROL
TR2
PIN
TIMER
INTERRUPT
CAPTURE
TRANSITION
DETECTOR
RCAP2L
RCAP2H
T2EX
PIN
EXF2
CONTROL
EXEN2
*THE CORE CLOCK IS THE OUTPUT OF THE PLL
Figure 50. Timer/Counter 2, 16-Bit Capture Mode
Rev. A | Page 52 of 72
ADuC814
UART SERIAL INTERFACE
SBUF
The serial port is full duplex, meaning it can transmit and
receive simultaneously. It is also receive-buffered, meaning it
can begin receiving a second byte before a previously received
byte has been read from the receive register. However, if the first
byte still has not been read by the time reception of the second
byte is complete, the first byte is lost. The physical interface to
the serial data network is via Pins RxD (P3.0) and TxD (P3.1),
while the SFR interface to the UART is comprised of the
following registers.
The serial port receive and transmit registers are both accessed
through the SBUF SFR (SFR address = 99H). Writing to SBUF
loads the transmit register and reading SBUF accesses a
physically separate receive register.
SCON
UART Serial Port Control Register
SFR Address
Power-On Default
Bit Addressable
98H
00H
Yes
SM0
SM1
SM2
REN
TB8
RB8
TI
RI
Table 26. SCON SFR Bit Designations
Bit No.
Name Description
7
6
SM0
SM1
UART Serial Mode Select Bits.
These bits select the serial port operating mode as follows:
SM0
SM1
Selected Operating Mode
0
0
1
1
0
1
0
1
Mode 0: Shift Register, fixed baud rate (Core_Clk/2)
Mode 1: 8-bit UART, variable baud rate
Mode 2: 9-bit UART, fixed baud rate (Core_Clk/64) or (Core_Clk/32)
Mode 3: 9-bit UART, variable baud rate
5
SM2
Multiprocessor Communication Enable Bit.
Enables multiprocessor communication in Modes 2 and 3.
In Mode 0, SM2 should be cleared.
In Mode 1, if SM2 is set, RI is not activated if a valid stop bit is not received. If SM2 is cleared, RI is set as soon as the byte
of data is received.
In Mode 2 or 3, if SM2 is set, RI is not activated if the received ninth data bit in RB8 is 0. If SM2 is cleared, RI is set as soon
as the byte of data is received.
4
REN
Serial Port Receive Enable Bit.
Set by the user software to enable serial port reception.
Cleared by the user software to disable serial port reception.
Serial Port Transmit (Bit 9).
The data loaded into TB8 is the ninth data bit that is transmitted in Modes 2 and 3.
Serial port Receiver Bit 9.
The ninth data bit received in Modes 2 and 3 is latched into RB8. For Mode 1, the stop bit is latched into RB8.
Set by hardware at the end of the eighth bit in Mode 0, or at the beginning of the stop bit in Modes 1, 2, and 3.
Cleared by the user software.
3
2
1
0
TB8
RB8
TI
RI
Serial Port Receive Interrupt Flag.
Set by hardware at the end of the eighth bit in Mode 0, or halfway through the stop bit in Modes 1, 2, and 3.
Cleared by user software.
Rev. A | Page 53 of 72
ADuC814
Mode 0: 8-Bit Shift Register Mode
Reception is initiated when a 1-to-0 transition is detected on
RxD. Assuming a valid start bit was detected, character
reception continues. The start bit is skipped and the eight data
bits are clocked into the serial port shift register. When all eight
bits have been clocked in, the following events occur:
Mode 0 is selected by clearing both the SM0 and SM1 bits in the
SFR SCON. Serial data enters and exits through RxD. TxD
outputs the shift clock. Eight data bits are transmitted or
received. Transmission is initiated by any instruction that writes
to SBUF. The data is shifted out of the RxD line. The eight bits
are transmitted with the least-significant bit (LSB) first, as
shown in Figure 52.
•
The eight bits in the receive shift register are latched into
SBUF.
•
The ninth bit (stop bit) is clocked into RB8 in SCON. The
receiver interrupt flag (RI) is set if, and only if, the
following conditions are met at the time the final shift
pulse is generated:
Reception is initiated when the receive enable bit (REN) is 1
and the receive interrupt bit (RI) is 0. When RI is cleared the
data is clocked into the RxD line and the clock pulses are output
from the TxD line.
Mode 1: 8-Bit UART, Variable Baud Rate
o
o
RI = 0
Mode 1 is selected by clearing SM0 and setting SM1. Each data
byte (LSB first) is preceded by a start bit (Bit 0) and followed by
a stop bit (Bit 1). Therefore 10 bits are transmitted on TxD or
received on RxD. The baud rate is set by the Timer 1 or Timer 2
overflow rate, or a combination of the two (one for transmission
and the other for reception).
Either SM2 = 0 or SM2 = 1 and
the received stop bit = 1
If either of these conditions is not met, the received frame
is irretrievably lost, and RI is not set.
STOP BIT
START
BIT
D0
D1
D2
D3
D4
D5
D6
D7
Transmission is initiated by writing to SBUF. The write-to-
SBUF signal also loads a 1 (stop bit) into the ninth bit position
of the transmit shift register. The data is output bit by bit until
the stop bit appears on TxD and the transmit interrupt flag (TI)
is automatically set as shown in Figure 51.
TxD
TI
(SCON. 1)
SET INTERRUPT
I.E., READY FOR MORE DATA
Figure 51. UART Serial Port Transmission, Mode 1
MACHINE
CYCLE 1
MACHINE
CYCLE 2
MACHINE
CYCLE 7
MACHINE
CYCLE 8
S1 S2 S3 S4 S5 S6 S1 S2 S3 S4
S4 S5 S6 S1 S2 S3 S4 S5 S6
CORE
CLK
ALE
RxD
(DATA OUT)
DATA BIT 0
DATA BIT 1
DATA BIT 6
DATA BIT 7
TxD
(SHIFT CLOCK)
Figure 52. UART Serial Port Transmission, Mode 0
Rev. A | Page 54 of 72
ADuC814
Mode 0 Baud Rate Generation
Mode 2: 9-Bit UART with Fixed Baud Rate
Mode 2 is selected by setting SM0 and clearing SM1. In this
mode, the UART operates in 9-bit mode with a fixed baud rate.
The baud rate is fixed at Core_Clk/64 by default, although by
setting the SMOD bit in PCON, the frequency can be doubled
to Core_Clk/32. Eleven bits are transmitted or received, a start
bit (Bit 0), eight data bits, a programmable ninth bit, and a stop
bit (Bit 1). The ninth bit is most often used as a parity bit,
although it can be used for anything, including a ninth data bit
if required.
The baud rate in Mode 0 is fixed:
Mode 0 Baud Rate = (Core Clock Frequency/12)
Mode 2 Baud Rate Generation
The baud rate in Mode 2 depends on the value of the SMOD bit
in the PCON SFR. If SMOD = 0, the baud rate is 1/64 of the
core clock. If SMOD = 1, the baud rate is 1/32 of the core clock:
Mode 2 Baud Rate = (2SMOD/64) × (Core Clock Frequency)
To transmit, the eight data bits must be written into SBUF. The
ninth bit must be written into TB8 in SCON. When
Mode 1 and 3 Baud Rate Generation
transmission is initiated, the eight data bits (from SBUF) are
loaded into the transmit shift register (LSB first). The contents
of TB8 are loaded into the ninth bit position of the transmit
shift register. The transmission starts at the next valid baud rate
clock. The TI flag is set as soon as the stop bit appears on TxD.
The baud rates in Modes 1 and 3 are determined by the over-
flow rate in Timer 1 or Timer 2, or both (one for transmit and
the other for receive).
Timer 1 Generated Baud Rates
Reception for Mode 2 is similar to that of Mode 1. The eight
data bytes are input at RxD (LSB first) and loaded into the
receive shift register. When all eight bits have been clocked in,
the following events occur:
When Timer 1 is used as the baud rate generator, the baud rates
in Modes 1 and 3 are determined by the Timer 1 overflow rate
and the value of SMOD as follows:
Modes 1 and 3 Baud Rate = (2SMOD/32) ×
(Timer 1 Overflow Rate)
•
The eight bits in the receive shift register are latched into
SBUF.
The Timer 1 interrupt should be disabled in this application.
The timer itself can be configured for either timer or counter
operation, and in any of its three running modes. In the most
typical application, it is configured for timer operation, in the
autoreload mode (high nibble of TMOD = 0100 binary). In that
case, the baud rate is given by the formula
•
•
The ninth data bit is latched into RB8 in SCON.
The receiver interrupt flag (RI) is set if, and only if, the
following conditions are met at the time the final shift
pulse is generated:
Modes 1 and 3 Baud Rate = (2SMOD/32) × (Core Clock/
(12 × [256 − TH1]))
o
o
RI = 0
Either SM2 = 0 or
SM2 = 1 and the received stop bit = 1
A very low baud rate can also be achieved with Timer 1 by leav-
ing the Timer 1 interrupt enabled, and configuring the timer to
run as a 16-bit timer (high nibble of TMOD = 0100 binary), and
using the Timer 1 interrupt to do a 16-bit software reload.
Table 27 shows some commonly used baud rates and how they
might be calculated from a core clock frequency of 2.0971 MHz
and 16.78 MHz. Generally speaking, a 5ꢀ error is tolerable
using asynchronous (start/stop) communications.
If either of these conditions is not met, the received frame
is irretrievably lost, and RI is not set.
Mode 3: 9-Bit UART with Variable Baud Rate
Mode 3 is selected by setting both SM0 and SM1. In this mode,
the 8051 UART serial port operates in 9-bit mode with a
variable baud rate determined by either Timer 1 or Timer 2.
The operation of the 9-bit UART is the same as for Mode 2 but
the baud rate can be varied as for Mode 1.
Table 27. Commonly Used Baud Rates, Timer 1
Ideal
Baud
Core
CLK
SMOD
Value
TH1-Reload
Value
Actual
Baud
%
Error
In all four modes, transmission is initiated by any instruction
that uses SBUF as a destination register. Reception is initiated in
Mode 0 by the condition RI = 0 and REN = 1. Reception is
initiated in the other modes by the incoming start bit if REN = 1.
9600
2400
1200
1200
16.78
16.78
16.78
2.10
1
1
1
1
–9 (F7H)
–36 (DCH)
–73 (B7H)
–9 (F7H)
9709
2427
1197
1213
1.14
1.14
0.25
1.14
UART Serial Port Baud Rate Generation
In these descriptions that follow, Core Clock Frequency refers to
the core clock frequency selected via the CD0–CD2 bits in the
PLLCON SFR.
Rev. A | Page 55 of 72
ADuC814
Timer 2 Generated Baud Rates
Baud rates can also be generated using Timer 2. Using Timer 2
is similar to using Timer 1 in that the timer must overflow 16
times before a bit is transmitted/received. Because Timer 2 has a
16-bit autoreload mode, a wide range of baud rates is possible
using Timer 2.
In this case, the baud rate is given by the formula
Modes 1 and 3 Baud Rate = (Core Clk)/
(32 × [65536 – (RCAP2H, RCAP2L)])
Table 28 shows some commonly used baud rates and how they
could be calculated from a core clock frequency of 2.0971 MHz
and 16.7772 MHz.
Modes 1 and 3 Baud Rate = (1/16) × (Timer 2 Overflow Rate)
Therefore, when Timer 2 is used to generate baud rates, the
timer increments every two clock cycles and not every core
machine cycle as before. Therefore, it increments six times faster
than Timer 1, and therefore baud rates six times faster are
possible. Because Timer 2 has 16-bit autoreload capability, very
low baud rates are still possible. Timer 2 is selected as the baud
rate generator by setting the CLK and/or RCLK in T2CON. The
baud rates for transmit and receive can be simultaneously
different. Setting RCLK and/or TCLK puts Timer 2 into its baud
rate generator mode as shown in Figure 53.
Table 28. Commonly Used Baud Rates, Timer 2
Ideal
Baud
Core
CLK
RCAP2H RCAP2L
Actual
Baud
%
Error
Value
Value
19200
9600
2400
1200
9600
2400
1200
16.78
16.78
16.78
16.78
2.10
–1 (FFH)
–1 (FFH)
–1 (FFH)
–2 (FEH)
–1 (FFH)
–1 (FFH)
–1 (FFH)
–27 (E5H)
–55 (C9H)
–218 (26H)
–181 (4BH)
–7 (FBH)
19418
9532
2405
1199
9362
2427
1191
1.14
0.7
0.21
0.02
2.4
2.10
2.10
–27 (ECH)
–55 (D7H)
1.14
0.7
TIMER 1
OVERFLOW
÷2
NOTE: OSCILLATOR FREQUENCY IS DIVIDED BY 2, NOT 12
0
1
SMOD
CONTROL
CORE
CLK*
÷2
TIMER 2
OVERFLOW
C/T2 = 0
C/T2 = 1
1
1
0
0
TL2
(8 BITS)
TL2
(8 BITS)
RCLK
T2
PIN
RX
CLOCK
÷16
TR2
TCLK
÷16
RELOAD
RCAP2H
TX
CLOCK
NOTE: AVAILABILITY OF ADDITIONAL
EXTERNAL INTERRUPT
RCAP2L
T2EX
PIN
TIMER 2
INTERRUPT
EXF 2
CONTROL
EXEN2
TRANSITION
DETECTOR
*THE CORE CLOCK IS THE OUTPUT OF THE PLL
Figure 53. Timer 2, UART Baud Rates
Rev. A | Page 56 of 72
ADuC814
INTERRUPT SYSTEM
The ADuC814 provides a total of twelve interrupt sources with two priority levels. The control and configuration of the interrupt system
is carried out through three interrupt-related SFRs.
IE
Interrupt Enable Register
IP
IEIP2
Interrupt Priority Register
Secondary Interrupt Enable and Priority Register
IE
Interrupt Enable Register
SFR Address
Power-On Default
Bit Addressable
A8H
00H
Yes
EA
EADC
ET2
ES
ET1
EX1
ET0
EX0
Table 29. IE SFR Bit Designations
Bit No.
Name Description
7
EA
Global Interrupt Enable.
Set by the user to enable all interrupt sources.
Cleared by the user to disable all interrupt sources.
ADC Interrupt.
Set by the user to enable the ADC interrupt.
Cleared by the user to disable the ADC interrupt.
Timer 2 Interrupt.
Set by the user to enable the Timer 2 interrupt.
Cleared by the user to disable the Timer 2 interrupt.
UART Serial Port Interrupt.
Set by the user to enable the UART serial port interrupt.
Cleared by the user to disable the UART serial port interrupt.
Timer 1 Interrupt.
Set by the user to enable the Timer 1 interrupt.
Cleared by the user to disable the Timer 1 interrupt.
INT1 Interrupt.
Set by the user to enable the External Interrupt 1.
Cleared by the user to disable the External Interrupt 1.
Timer 0 Interrupt.
Set by the user to enable the Timer 0 interrupt.
Cleared by the user to disable the Timer 0 interrupt.
INT0 Interrupt.
6
5
4
3
2
1
0
EADC
ET2
ES
ET1
EX1
ET0
EX0
Set by the user to enable the External Interrupt 0.
Cleared by the user to disable the External Interrupt 0.
Rev. A | Page 57 of 72
ADuC814
IP
Interrupt Priority Register
SFR Address
Power-On Default
Bit Addressable
B8H
00H
Yes
---
PADC
PT2
PS
PT1
PX1
PT0
PX0
Table 30. IP SFR Bit Designations
Bit No.
Name
Description
7
6
---
PADC
Reserved.
ADC Interrupt Priority.
Written to by user to set interrupt priority level (1 = High; 0 = Low).
Timer 2 Interrupt Priority.
Written to by the user to set interrupt priority level (1 = High; 0 = Low).
UART Serial Port Interrupt Priority.
Written to by the user to set interrupt priority level (1 = High; 0 = Low).
Timer 1 Interrupt Priority.
Written to by the user to set interrupt priority level (1 = High; 0 = Low).
External Interrupt 1 Priority (INT1).
Written to by the user to set interrupt priority level (1 = High; 0 = Low).
Timer 0 Interrupt Priority.
Written to by the user to set interrupt priority level (1 = High; 0 = Low).
External Interrupt 0 Priority (INT0).
5
4
3
2
1
0
PT2
PS
PT1
PX1
PT0
PX0
Written to by the user to set interrupt priority level (1 = High; 0 = Low).
IEIP2
Secondary Interrupt Enable and Priority Register
SFR Address
Power-On Default
Bit Addressable
A9H
A0H
No
---
PT1
PPSM
PSI
---
ETI
EPSM
ESI
Table 31. IEIP2 SFR Bit Designations
Bit No.
Name
Description
7
6
---
PTI
Reserved.
Time Interval Counter Interrupt Priority.
Written to by the user to set TIC interrupt priority (1 = High; 0 = Low).
PSM Interrupt Priority.
Written to by the user to select power supply monitor interrupt priority (1 = High; 0 = Low).
SPI Serial Port Interrupt Priority.
5
4
PPSM
PSI
Written to by the user to select SPI serial port interrupt priority (1 = High; 0 = Low).
Reserved. This bit must be 0.
TIC Interrupt.
3
2
---
ETI
Set by the user to enable the TIC interrupt.
Cleared by the user to disable the TIC interrupt.
Power Supply Monitor Interrupt.
Set by the user to enable the power supply monitor interrupt.
Cleared by the user to disable the power supply monitor interrupt.
SPI Serial Port Interrupt.
1
0
EPSM
ESI
Set by the user to enable the SPI serial port interrupt.
Cleared by the user to disable the SPI serial port interrupt.
Rev. A | Page 58 of 72
ADuC814
Interrupt Priority
Interrupt Vectors
The interrupt enable registers are written by the user to enable
individual interrupt sources, while the interrupt priority
registers allow the user to select one of two priority levels for
each interrupt. An interrupt of a high priority may interrupt the
service routine of a low priority interrupt, and if two interrupts
of different priority occur at the same time, the higher level
interrupt is serviced first. An interrupt cannot be interrupted by
another interrupt of the same priority level. If two interrupts of
the same priority level occur simultaneously, a polling sequence
is observed as shown in Table 32.
When an interrupt occurs, the program counter is pushed onto
the stack, and the corresponding interrupt vector address is
loaded into the program counter. The interrupt vector addresses
are shown in Table 33.
Table 33. Interrupt Vector Addresses
Source
Vector Address
IE0
0003H
TF0
000BH
IE1
0013H
TF1
001BH
Table 32. Priority within an Interrupt Level
RI + TI
0023H
Source
PSMI
WDS
IE0
RDY0/RDY1
TF0
IE1
TF1
ISPI
Priority
Description
TF2 + EXF2
RDY0/RDY1 (ADC)
ISPI
PSMI
002BH
0033H
003BH
0043H
0053H
005BH
1 (Highest)
2
3
4
5
6
7
8
Power Supply Monitor Interrupt
Watchdog Interrupt
External Interrupt 0
ADC Interrupt
Timer/Counter 0 Interrupt
External Interrupt 1
Timer/Counter 1 Interrupt
SPI Interrupt
TII
WDS (WDIR = 1)1
1 The watchdog can be configured to generate an interrupt instead of a reset
when it times out. This is used for logging errors or to examine the internal
status of the microcontroller core to understand, from a software debug point
of view, why a watchdog timeout occurred. The watchdog interrupt is slightly
different from normal interrupts in that its priority level is always set to 1, and
it is not possible to disable the interrupt via the global disable bit (EA) in the IE
SFR. This is done to ensure that the interrupt is always responded to if a
watchdog timeout occurs. The watchdog produces an interrupt only if the
watchdog timeout is greater than zero.
RI + TI
TF2 + EXF2
TII
9
10
Serial Interrupt
Timer/Counter 2 Interrupt
11 (Lowest) Time Interval Counter Interrupt
Rev. A | Page 59 of 72
ADuC814
ADuC814 HARDWARE DESIGN CONSIDERATIONS
DIGITAL SUPPLY
ANALOG SUPPLY
This section outlines some key hardware design considerations
for integrating the ADuC814 into any hardware system.
10µF
10µF
+
–
+
–
ADuC814
CLOCK OSCILLATOR
AV
DD
DV
As described earlier, the core clock frequency for the ADuC814
is generated from an on-chip PLL that locks onto a multiple
(512 times) of 32.768 kHz. The latter is generated from an
internal clock oscillator. To use the internal clock oscillator,
connect a 32.768 kHz parallel resonant crystal between XTAL1
and XTAL2 pins (Pins 26 and 27) as shown in Figure 54.
DD
0.1µF
0.1µF
AGND
DGND
Figure 55. External Dual-Supply Connections
As shown in the typical external crystal connection diagram in
Figure 54, two internal 12 pF capacitors are provided on-chip.
These are connected internally, directly to the XTAL1 and
XTAL2 pins. The total input capacitances at both pins is
detailed in the Specifications table. The value of the total load
capacitance required for the external crystal should be the value
recommended by the crystal manufacturer for use with that
specific crystal. In many cases, because of the on-chip capacitors,
additional external load capacitors are not required.
DIGITAL SUPPLY
1.6Ω
10µF
BEAD
10µF
+
–
AV
DD
DV
DD
0.1µF
0.1µF
ADuC814
AGND
ADuC814
DGND
XTAL1
12pF
Figure 56. External Single-Supply Connections
Notice that in both Figure 55 and Figure 56, a large value
(10 µF) reservoir capacitor sits on DVDD and a separate 10 µF
capacitor sits on AVDD. Also, local small-value (0.1 µF) capacitors
are located at each VDD pin of the chip. As per standard design
practice, be sure to include all of these capacitors, and ensure
that the smaller capacitors are closest to each AVDD pin with
trace lengths as short as possible. Connect the ground terminal
of each of these capacitors directly to the underlying ground
plane. Finally, note that, at all times, the analog and digital ground
pins on the ADuC814 should be referenced to the same system
ground reference point.
TO PLL
XTAL2
12pF
Figure 54. External Parallel Resonant Crystal Connections
As an alternative to providing two separate power supplies,
AVDD can be kept quiet by placing a small series resistor and/or
ferrite bead between it and DVDD, and then decoupling AVDD
separately to ground. An example of this configuration is shown
in Figure 56. With this configuration, other analog circuitry
(such as op amps and voltage reference) can be powered from
the AVDD supply line as well.
POWER CONSUMPTION
POWER SUPPLIES
The CORE values given represent the current drawn by DVDD
,
The ADuC814’s operational power supply voltage range is 2.7 V
to 5.5 V. Although the guaranteed data sheet specifications are
given only for power supplies within 2.7 V to 3.3 V or 4.5 V to
5.5 V, ( 10ꢀ of the nominal level), the chip can function equally
well at any power supply level between 2.7 V and 5.5 V.
while the rest (ADC and DAC) are pulled by the AVDD pin and
can be disabled in software when not in use. The other on-chip
peripherals (such as watchdog timer and power supply monitor)
consume negligible current and are therefore lumped in with
the CORE operating current here. Of course, the user must add
any currents sourced by the parallel and serial I/O pins, and that
sourced by the DAC, in order to determine the total current
needed at the ADuC814’s supply pins. Also, current drawn from
the DVDD supply increases by approximately 5 mA during the
Flash/EE erase and program cycles.
Users should separate analog and digital power supply pins
(AVDD and DVDD) and allow AVDD to be kept relatively free of
noisy digital signals often present on the system DVDD line. In
this mode, the part can also operate with split supplies as long
as the supply voltages are within 0.3 V of each other. A typical
split-supply configuration is show in Figure 55.
Rev. A | Page 60 of 72
ADuC814
Power-Saving Modes
INT0
Interrupt
Setting the idle and power-down mode bits, PCON.0 and
PCON.1, respectively, in the PCON SFR described in Table 5,
allows the chip to be switched from normal mode to idle mode,
and also to full power-down mode.
Power-down mode is terminated and the CPU services the
INT0 interrupt. The RETI at the end of the ISR returns the core
to the instruction following the one that enabled power-down.
The INT0 pin must not be driven low during or within two
machine cycles of the instruction that initiates power-down
mode. Note that the
(INT0PD) in the PCON SFR must first be set to allow this mode
of operation.
In idle mode, the oscillator continues to run, but the core clock
generated from the PLL is halted. The on-chip peripherals con-
tinue to receive the clock and remain functional. The CPU status
is preserved with the stack pointer, program counter, and all
other internal registers maintaining their data during idle mode.
Port pins and DAC output pins also retain their states in this
mode. The chip recovers from idle mode upon receiving any
enabled interrupt, or upon receiving a hardware reset.
INT0
power-down interrupt enable bit
Power-On Reset
An internal POR (power-on-reset) is implemented on the
ADuC814. For DVDD below 2.45 V, the internal POR holds the
ADuC814 in reset. As DVDD rises above 2.45 V, an internal timer
times out for approximately128 ms before the part is released
from reset. The user must ensure that the power supply has
reached a stable 2.7 V minimum level by this time. Likewise on
power-down, the internal POR holds the ADuC814 in reset
until the power supply has dropped below 1 V. Figure 57
illustrates the operation of the internal POR in detail.
In power-down mode, both the PLL and the clock to the core
are stopped. The on-chip oscillator can be halted or can
continue to oscillate depending on the state of the oscillator
power-down bit (OSC_PD) in the PLLCON SFR. The TIC,
being driven directly from the oscillator, can also be enabled
during power-down. All other on-chip peripherals however, are
shut down. Port pins retain their logic levels in this mode, but
the DAC output goes to a high impedance state (three-state).
During full power-down mode, the ADuC814 consumes a total
of 5 µA typically. There are five ways of terminating power-
down mode, as described in the next sections.
2.45V TYP
DV
DD
1.0V
1.0V TYP
128ms TYP
128ms TYP
INTERNAL
CORE RESET
Asserting RESET (Pin 10)
Returns to normal mode and all registers are set to their default
state. Program execution starts at the reset vector once the RESET
pin is de-asserted.
Figure 57. Internal POR Operation
Grounding and Board Layout Recommendations
Cycling Power
As with all high resolution data converters, special attention
must be paid to grounding and PC board layout of ADuC814
based designs in order to achieve optimum performance from
the ADCs and DAC. Although the ADuC814 has separate pins
for analog and digital ground (AGND and DGND), the user
must not tie these to two separate ground planes unless the two
ground planes are connected together very close to the ADuC814,
as illustrated in the simplified example of Figure 58a. In systems
where digital and analog ground planes are connected together
somewhere else (at the system’s power supply for example), they
cannot be connected again near the ADuC814 because a ground
loop would result. In these cases, tie all of the ADuC814’s
AGND and DGND pins to the analog ground plane, as
illustrated in Figure 58b. In systems with only one ground plane,
ensure that the digital and analog components are physically
separated onto separate halves of the board such that digital
return currents do not flow near analog circuitry and vice versa.
The ADuC814 can then be placed between the digital and
analog sections, as illustrated in Figure 58c.
All registers are set to their default state and program execution
starts at the reset vector.
Time Interval Counter (TIC) Interrupt
Power-down mode is terminated and the CPU services the TIC
interrupt. The RETI at the end of the TIC interrupt service
routine returns the core to the instruction following the one
that enabled power-down.
SPI Interrupt
Power-down mode is terminated and the CPU services the SPI
interrupt. The RETI at the end of the ISR returns the core to the
instruction following the one that enabled power-down. Note
that the SPI power-down interrupt enable bit (SERIPD) in the
PCON SFR must first be set to allow this mode of operation.
Rev. A | Page 61 of 72
ADuC814
OTHER HARDWARE CONSIDERATIONS
To facilitate in-circuit programming, in-circuit debug, and
emulation options, users should implement some simple
connection points in their hardware. A typical ADuC814
connection diagram is shown in Figure 59.
PLACE ANALOG
COMPONENTS
HERE
PLACE DIGITAL
COMPONENTS
HERE
a.
AGND
DGND
In-Circuit Serial Download Access
Nearly all ADuC814 designs will want to take advantage of the
in-circuit reprogrammability of the chip. This is accomplished
by a connection from the ADuC814’s UART to a PC, which
requires an external RS-232 chip for level translation. If users
would rather not design an RS-232 chip onto a board, refer to
the Application Note uC006, A 4-Wire UART-to-PC Interface
(available at www.analog.com/microconverter) for a simple
(and zero-cost-per-board) method of gaining in-circuit serial
download access to the ADuC814.
PLACE ANALOG
COMPONENTS
PLACE DIGITAL
COMPONENTS
HERE
b.
HERE
AGND
DGND
In addition to the basic UART connections, users also need a
way to trigger the chip into download mode. This is accom-
plished via a 1 kΩ pull-up resistor that can be jumpered onto
the DLOAD pin. To get the ADuC814 into download mode,
simply connect this jumper and power-cycle the device (or
manually reset the device, if a manual reset button is available),
and it will be ready to receive a new program serially. To enable
the device to enter normal mode (and run the program) when-
ever power is cycled or RESET is toggled, the DLOAD pin must
be pulled low through a 1 kΩ resistor.
PLACE ANALOG
COMPONENTS
HERE
PLACE DIGITAL
COMPONENTS
HERE
c.
GND
Figure 58. System Grounding Schemes
In all of these scenarios, and in more complicated real-life appli-
cations, keep in mind the flow of current from the supplies and
back to ground. Make sure the return paths for all currents are
as close as possible to the paths the currents took to reach their
destinations. For example, do not put power components on the
analog side of Figure 58b with DVDD because that would force
return currents from DVDD to flow through AGND. Also, try to
avoid digital currents flowing under analog circuitry, which
could happen if a noisy digital chip is placed on the left half of
the board in Figure 58c. Whenever possible, avoid large
discontinuities in the ground plane(s) (such as are formed by a
long trace on the same layer), because they force return signals
to travel a longer path. And of course, make all connections to
the ground plane directly, with little or no trace separating the
pin from its via to ground.
Embedded Serial Port Debugger
From a hardware perspective, entry to serial port debug mode is
identical to the serial download entry sequence described in the
preceding section. In fact, both serial download and serial port
debug modes can be thought of as essentially one mode of
operation used in two different ways. Note that the serial port
debugger is fully contained on the ADuC814 device, unlike
ROM monitor type debuggers.
If the user plans to connect fast logic signals (rise/fall time
< 5 ns) to any of the ADuC814’s digital inputs, add a series
resistor to each relevant line to keep rise and fall times longer
than 5 ns at the ADuC814 input pins. A value of 100 Ω or 200 Ω
is usually sufficient to prevent high speed signals from coupling
capacitively into the ADuC814 and affecting the accuracy of
ADC conversions.
Rev. A | Page 62 of 72
ADuC814
DV
DD
1kΩ
2-PIN HEADER FOR
EMULATION ACCESS
(NORMALLY OPEN)
DV
DD
DOWN LOAD/DEBUG
ENABLE JUMPER
(NORMALLY OPEN)
0.1µF
1
2
DGND
DLOAD
RXD
DV
28
27
26
25
24
23
22
21
20
19
18
DD
XTAL2
XTAL1
3
4
TXD
32.766kHz
5
6
ADuC814
7
8
DAC1
DAC0
9
DV
DAC1
DD
ANALOG
INPUT
OUTPUT
RESET
ADC0
DAC0
10
11
10
Ω
OUTPUT
10nF
AV
12
13
14
17
16
15
C
REF
DD
0.1
0.1
µF
AV
DD
V
V
REF
REF
µ
F
OUTPUT
AGND
AGND
DV
DD
ADM202
C1+
1
2
3
4
5
6
7
8
16
V
CC
15
14
13
12
11
10
9
1
V1+
GND
2
3
4
5
C1–
C2+
C2–
T1OUT
R1IN
R1OUT
V–
T1IN
T2IN
T2OUT
R2IN
6
7
8
9
R2OUT
Figure 59. Typical ADuC814 System Connection Diagram
Single-Pin Emulation Mode
2-pin header. To be compatible with the standard connector
that comes with the single-pin emulator available from
Accutron Limited (www.accutron.com), use a
2-pin 0.1-inch pitch friction lock header from Molex
(www.molex.com) such as their part number 22-27-2021. Be
sure to observe the polarity of this header. When the friction
lock tab is at the right, the ground pin should be the lower of
the two pins (when viewed from the top).
Also built into the ADuC814 is a dedicated controller for single-
pin in-circuit emulation (ICE) using standard production
ADuC814 devices. In this mode, emulation access is gained by
connection to a single pin, again the DLOAD pin is used for this
function. As described previously, this pin is either high to
enable entry into serial download and serial debug modes or
low to select normal code execution. To enable single-pin
emulation mode, however, users need to pull the DLOAD pin
high through a 1 kΩ resistor. The emulator then connects to the
Rev. A | Page 63 of 72
ADuC814
TIMING SPECIFICATIONS1,2,3
Table 34. Clock Input (External Clock Driven XTAL1)
AVDD = 2.7 V to 3.3 V or 4.75 V to 5.25 V, DVDD = 2.7 V to 3.3 V or 4.75 V to 5.25 V; all specifications TMIN to TMAX, unless otherwise noted
32.768 kHz External Crystal
Parameter
tCK
tCKL
tCKH
tCKR
Unit
µs
µs
µs
ns
Min
Typ
30.52
15.16
15.16
20
Max
XTAL1 Period
XTAL1 Width Low
XTAL1 Width High
XTAL1 Rise Time
tCKF
XTAL1 Fall Time
20
ns
MHz
µs
1/tCORE
tCORE
tCYC
ADuC814 Core Clock Frequency4
ADuC814 Core Clock Period5
ADuC814 Machine Cycle Time6
0.131
0.72
16.78
91.55
0.476
5.7
µs
1 AC inputs during testing are driven at DVDD – 0.5 V for a Logic 1, and at 0.45 V for a Logic 0. Timing measurements are made at VIH min for a Logic 1, and at VIL max for a
Logic 0 as shown in Figure 61.
2 For timing purposes, a port pin is no longer floating when a 100 mV change from load voltage occurs. A port pin begins to float when a 100 mV change from the
loaded VOH/VOL level occurs as shown in Figure 61.
3 CLOAD for all outputs = 80 pF, unless otherwise noted.
4 ADuC814 internal PLL locks onto a multiple (512 times) the external crystal frequency of 32.768 kHz to provide a stable 16.777216 MHz internal clock for the system.
The core can operate at this frequency or at a binary submultiple called Core_Clk, selected via the PLLCON SFR.
5 This number is measured at the default Core_Clk operating frequency of 2.09 MHz.
6 ADuC814 Machine Cycle Time is nominally defined as 12/Core_CLK.
tCKR
tCKH
tCKL
tCKF
tCK
Figure 60. XTAL1 Input
DV – 0.5V
DD
V
– 0.1V
+ 0.1V
V
V
– 0.1V
LOAD
LOAD
LOAD
LOAD
0.2DV
+ 0.9V
DD
TIMING
REFERENCE
POINT
V
V
LOAD
TEST POINTS
0.2DV – 0.1V
LOAD
DD
V
+ 0.1V
0.45V
Figure 61. Timing Waveform Characteristics
Rev. A | Page 64 of 72
ADuC814
Table 35. UART Timing (Shift Register Mode)
16.78 MHz Core_Clk
Variable Core_Clk
Parameter
Unit
µs
ns
ns
ns
Min
Typ
Max
Min
Typ
Max
tXLXL
Serial Port Clock Cycle Time
Output Data Setup to Clock
Input Data Setup to Clock
Input Data Hold after Clock
Output Data Hold after Clock
715
12 tCORE
–133
+133
tQVXH
tDVXH
tXHDX
tXHQX
463
252
0
10 tCORE
2 tCORE
0
22
2 tCORE
–117
ns
tXLXL
TxD
(OUTPUT CLOCK)
SET RI
OR
tQVXH
SET TI
tXHQX
RxD
LSB
BIT 1
BIT 6
(OUTPUT DATA)
tDVXH
tXHDX
RxD
(INPUT DATA)
LSB
BIT 1
BIT 6
MSB
Figure 62. UART Timing in Shift Register Mode
Rev. A | Page 65 of 72
ADuC814
Table 36. SPI Master Mode Timing (CPHA = 1)
Parameter
Min
Typ
630
630
Max
Unit
ns
ns
ns
ns
ns
ns
ns
ns
tSL
tSH
SCLOCK Low Pulse Width1
SCLOCK High Pulse Width1
Data Output Valid after SCLOCK Edge
Data Input Setup Time before SCLOCK Edge
Data Input Hold Time after SCLOCK Edge
Data Output Fall Time
Data Output Rise Time
SCLOCK Rise Time
SCLOCK Fall Time
tDAV
tDSU
tDHD
tDF
tDR
tSR
50
100
100
10
10
10
10
25
25
25
25
tSF
ns
1 Characterized under the following conditions:
a. Core clock divider bits CD2, CD1, and CD0 in PLLCON SFR set to 0, 1, and 1, respectively, i.e., core clock frequency = 2.09 MHz.
b. SPI bit-rate selection bits SPR1 and SPR0 bits in SPICON SFR set to 0 and 0, respectively.
SCLOCK
(CPOL = 0)
tSH
tSL
tSR
tSF
SCLOCK
(CPOL = 1)
tDAV
tDF
tDR
MOSI
MISO
MSB
BITS 6–1
LSB
BITS 6–1
LSB IN
MSB IN
tDSU tDHD
Figure 63. SPI Master Mode Timing (CPHA = 1)
Rev. A | Page 66 of 72
ADuC814
Table 37. SPI Master Mode Timing (CPHA = 0)
Parameter
Min
Typ
630
630
Max
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tSL
tSH
SCLOCK Low Pulse Width1
SCLOCK High Pulse Width1
tDAV
tDOSU
tDSU
tDHD
tDF
tDR
tSR
tSF
Data Output Valid after SCLOCK Edge
Data Output Setup before SCLOCK Edge
Data Input Setup Time before SCLOCK Edge
Data Input Hold Time after SCLOCK Edge
Data Output Fall Time
Data Output Rise Time
SCLOCK Rise Time
SCLOCK Fall Time
50
150
100
100
10
10
10
10
25
25
25
25
1 Characterized under the following conditions:
a. Core clock divider bits CD2, CD1, and CD0 bits in PLLCON SFR set to 0, 1, and 1, respectively, i.e., core clock frequency = 2.09 MHz.
b. SPI bit-rate selection bits SPR1 and SPR0 bits in SPICON SFR set to 0 and 0, respectively.
SCLOCK
(CPOL = 0)
tSH
tSL
tSR
tSF
SCLOCK
(CPOL = 1)
tDAV
tDF
tDR
tDOSU
MOSI
MISO
MSB
BITS 6–1
LSB
MSB IN
BITS 6–1
LSB IN
tDSU tDHD
Figure 64. SPI Master Mode Timing (CPHA = 0)
Rev. A | Page 67 of 72
ADuC814
Table 38. SPI Slave Mode Timing (CPHA = 1)
Parameter
Min
Typ
Max
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tSS
SS to SCLOCK Edge
0
tSL
tSH
SCLOCK Low Pulse Width
SCLOCK High Pulse Width
Data Output Valid after SCLOCK Edge
Data Input Setup Time before SCLOCK Edge
Data Input Hold Time after SCLOCK Edge
Data Output Fall Time
Data Output Rise Time
SCLOCK Rise Time
SCLOCK Fall Time
SS High after SCLOCK Edge
330
330
tDAV
tDSU
tDHD
tDF
tDR
tSR
50
100
100
10
10
10
10
25
25
25
25
tSF
tSFS
0
SS
tSS
tDF
tSFS
SCLOCK
(CPOL = 0)
tSH
tSL
tSR
tSF
SCLOCK
(CPOL = 1)
tDAV
tDF
tDR
MOSI
MISO
MSB
BITS 6–1
LSB
BITS 6–1
LSB IN
MSB IN
tDSU tDHD
Figure 65. SPI Slave Mode Timing (CPHA = 1)
Rev. A | Page 68 of 72
ADuC814
Table 39. SPI Slave Mode Timing (CPHA = 0)
Parameter
Min
Typ
Max
Unit
tSS
SS to SCLOCK Edge
0
tSL
tSH
tDAV
tDSU
tDHD
tDF
tDR
tSR
tSF
SCLOCK Low Pulse Width
SCLOCK High Pulse Width
Data Output Valid after SCLOCK Edge
Data Input Setup Time before SCLOCK Edge
Data Input Hold Time after SCLOCK Edge
Data Output Fall Time
Data Output Rise Time
SCLOCK Rise Time
SCLOCK Fall Time
SS to SCLOCK Edge
330
330
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
50
100
100
10
10
10
10
25
25
25
25
50
20
tSSR
tDOSS
tSFS
Data Output Valid after SS Edge
SS High after SCLOCK Edge
0
SS
tSS
tSFS
SCLOCK
(CPOL = 0)
tSH
tSL
tSR
tSF
SCLOCK
(CPOL = 1)
tDAV
tDOSU
tDF
tDR
MOSI
MISO
MSB
BITS 6–1
LSB
MSB IN
BITS 6–1
LSB IN
tDSU tDHD
Figure 66. SPI Slave Mode Timing (CPHA = 0)
Rev. A | Page 69 of 72
ADuC814
OUTLINE DIMENSIONS
9.80
9.70
9.60
28
15
4.50
4.40
4.30
6.40 BSC
1
14
PIN 1
0.65
BSC
1.20 MAX
0.15
0.05
8°
0°
0.75
0.60
0.45
0.30
0.19
0.20
0.09
SEATING
PLANE
COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-153AE
Figure 67. 28-Lead Thin Shrink Small Outline Package (TSSOP) (RU-28)
Dimensions shown in mm
Rev. A | Page 70 of 72
ADuC814
ORDERING GUIDE
Model
ADuC814ARU
ADuC814ARU-REEL
ADuC814ARU-REEL7
ADuC814BRU
ADuC814BRU-REEL
ADuC814BRU-REEL7
Temperature Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Package Description
Package Option
Thin Shrink Small Outline (TSSOP)
Thin Shrink Small Outline (TSSOP)
Thin Shrink Small Outline (TSSOP)
Thin Shrink Small Outline (TSSOP)
Thin Shrink Small Outline (TSSOP)
Thin Shrink Small Outline (TSSOP)
RU-28
RU-28
RU-28
RU-28
RU-28
RU-28
QuickStart Development System Model
Description
EVAL-ADUC814QS
Development System for the ADuC814 MicroConverter
QuickStart PLUS Development System
EVAL-ADUC814QSP1
1Only available to order through the web.
Rev. A | Page 71 of 72
ADuC814
NOTES
Purchase of licensed I2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips
I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.
©
2003 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C02748-0-12/03(A)
Rev. A | Page 72 of 72
相关型号:
ADUC814ARU-REEL7
8-BIT, FLASH, 16.78 MHz, MICROCONTROLLER, PDSO28, 4.40 X 9.70 MM, MO-153AE, TSSOP-28
ROCHESTER
ADUC814ARUZ
8-BIT, FLASH, 16.78MHz, MICROCONTROLLER, PDSO28, 4.40 X 9.70 MM, MO-153AE, TSSOP-28
ROCHESTER
ADUC814BRU
8-BIT, FLASH, 16.78 MHz, MICROCONTROLLER, PDSO28, 4.40 X 9.70 MM, MO-153AE, TSSOP-28
ROCHESTER
ADUC814BRUZ
8-BIT, FLASH, 16.78MHz, MICROCONTROLLER, PDSO28, 4.40 X 9.70 MM, MO-153AE, TSSOP-28
ROCHESTER
ADUC814BRUZ-REEL
Precision Analog Microcontroller: 1.3MIPS 8052 MCU + 8kB Flash + 6-Ch 12-Bit ADC + Dual 12-Bit DAC
ADI
©2020 ICPDF网 联系我们和版权申明