ADUM4154ARIZ [ADI]
5 kV, 7-Channel, SPIsolator Multiple Slave, Digital Isolator for SPI;型号: | ADUM4154ARIZ |
厂家: | ADI |
描述: | 5 kV, 7-Channel, SPIsolator Multiple Slave, Digital Isolator for SPI 光电二极管 接口集成电路 |
文件: | 总23页 (文件大小:397K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
5 kV, 7-Channel, SPIsolator
Multiple Slave, Digital Isolator for SPI
Data Sheet
ADuM4154
FEATURES
FUNCTIONAL BLOCK DIAGRAM
Supports up to 17 MHz SPI clock speed
4 high speed, low propagation delay, SPI signal isolation
channels
V
1
2
20
19
V
DD1
DD2
GND
ADuM4154
ENCODE
GND
1
2
DECODE
DECODE
ENCODE
DECODE
MCLK
MO
3
18 SCLK
ENCODE
Supports up to 4 slave devices
SI
4
17
16
15
14
13
12
11
20-lead SOIC_IC package with 8.3 mm creepage
High temperature operation: 125°C
High common-mode transient immunity: >25 kV/µs
Safety and regulatory approvals
DECODE
SO
MI
5
ENCODE
MSS
SSA0
SSA1
NIC
SS0
SS1
SS2
SS3
GND
6
7
MUX
UL recognition per UL 1577
CONTROL
BLOCK
8
5000 V rms for 1 minute SOIC long package
CSA Component Acceptance Notice 5A
VDE certificate of conformity
9
CONTROL
BLOCK
GND
1
10
2
DIN V VDE V 0884-10 (VDE V 0884-10):2006-12
Figure 1.
V
IORM = 849 V peak
APPLICATIONS
Industrial programmable logic controllers (PLCs)
Sensor isolation
GENERAL DESCRIPTION
The ADuM41541 is an SPIsolator™ digital isolator optimized for
a serial peripheral interface (SPI) that includes support for up to
four slave devices. Based on the Analog Devices, Inc., iCoupler®
chip scale transformer technology, the low propagation delay and
Table 1. Related Products
Product
Description
ADuM3150
3.75 kV, high speed, clock delayed
SPIsolator
3.75 kV, multichannel SPIsolator
SS
jitter in the CLK, MO/SI, MI/SO, and SPI bus signals support
ADuM3151/ADuM3152/
ADuM3153
SPI clock rates of up to 17 MHz.
ADuM3154
ADuM4150
3.75 kV, multiple slave SPIsolator
5 kV, high speed, clock delayed
SPIsolator
The ADuM4154 isolator also provides a slave select multiplexing
system that allows up to four slave devices to be serviced from
one isolator. When a target slave is selected, the slave select
signal propagates to the desired output with low propagation
delay, allowing tight timing control. The isolated SSx is addressed
through a 250 kbps low speed, 2-channel address bus, allowing
the target slave device to be changed in as little as 2.5 µs.
ADuM4151/ADuM4152/
ADuM4153
5 kV, multichannel SPIsolator
1 Protected by U.S. Patents 5,952,849; 6,262,600; 6,873,065; and 7075329. Other patents are pending.
Rev. B
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rightsof third parties that may result fromits use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks andregisteredtrademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2014–2017 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADUM4154* PRODUCT PAGE QUICK LINKS
Last Content Update: 07/22/2017
COMPARABLE PARTS
View a parametric search of comparable parts.
DESIGN RESOURCES
• ADUM4154 Material Declaration
• PCN-PDN Information
EVALUATION KITS
• ADUM3154/ADUM4154 Evaluation Board
• Quality And Reliability
• Symbols and Footprints
DOCUMENTATION
Data Sheet
DISCUSSIONS
View all ADUM4154 EngineerZone Discussions.
• ADuM4154: 5 kV, 7-Channel, SPIsolator Multiple Slave,
Digital Isolator for SPI Data Sheet
SAMPLE AND BUY
Visit the product page to see pricing options.
TOOLS AND SIMULATIONS
• ADuM3154/ADuM4154 IBIS Model
TECHNICAL SUPPORT
Submit a technical question or find your regional support
number.
DOCUMENT FEEDBACK
Submit feedback for this data sheet.
This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not
trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified.
ADuM4154
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Absolute Maximum Ratings ......................................................... 13
ESD Caution................................................................................ 13
Pin Configuration and Function Descriptions........................... 14
Typical Performance Characteristics ........................................... 16
Applications Information .............................................................. 17
Introduction................................................................................ 17
Printed Circuit Board (PCB) Layout ....................................... 19
Propagation Delay Related Parameters ................................... 19
DC Correctness and Magnetic Field Immunity..................... 19
Power Consumption .................................................................. 20
Insulation Lifetime..................................................................... 20
Outline Dimensions....................................................................... 22
Ordering Guide .......................................................................... 22
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description......................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Electrical Characteristics—5 V Operation................................ 3
Electrical Characteristics—3.3 V Operation ............................ 5
Electrical Characteristics—Mixed 5 V/3.3 V Operation ........ 7
Electrical Characteristics—Mixed 3.3 V/5 V Operation ........ 9
Package Characteristics ............................................................. 10
Regulatory Information............................................................. 11
Insulation and Safety Related Specifications .......................... 11
DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 Insulation
Characteristics ............................................................................ 12
Recommended Operating Conditions .................................... 12
REVISION HISTORY
7/2017—Rev. A to Rev. B
Changes to Logic High Parameter; Table 5 ................................... 6
Changes to Logic High Parameter; Table 7 ................................... 8
Changes to Logic High Parameter; Table 9 ................................. 10
3/2015—Rev. 0 to Rev. A
Changes to Features Section and Table 1 ...................................... 1
Changes to Supply Current Parameter, Table 3 ............................ 4
Changes to Supply Current Parameter, Table 5 ............................ 6
Changes to Supply Current Parameter, Table 7 ............................ 8
Changes to Supply Current Parameter, Table 9 .......................... 10
Changes to Table 11........................................................................ 11
Changes to Table 13........................................................................ 12
Changes to High Speed Channels Section .................................. 17
10/2014—Revision 0: Initial Version
Rev. B | Page 2 of 22
ADuM4154
Data Sheet
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS—5 V OPERATION
All typical specifications are at TA = 25°C and VDD1 = VDD2 = 5 V. Minimum and maximum specifications apply over the entire recommended
operation range: 4.5 V ≤ VDD1 ≤ 5.5 V, 4.5 V ≤ VDD2 ≤ 5.5 V, and −40°C ≤ TA ≤ +125°C, unless otherwise noted. Switching specifications
are tested with CL = 15 pF and CMOS signal levels, unless otherwise noted.
Table 2. Switching Specifications
A Grade
B Grade
Parameter
Symbol
Min Typ Max
Min
Typ Max
Unit
Test Conditions/Comments
MCLK, MO, SO
SPI Clock Rate
SPIMCLK
DRFAST
tPHL, tPLH
PW
1
2
25
17
34
14
MHz
Mbps
ns
Data Rate Fast (MO, SO)
Propagation Delay
Pulse Width
Within PWD limit
50% input to 50% output
Within PWD limit
12
100
12.5
ns
Pulse Width Distortion
Codirectional Channel Matching1
Jitter, High Speed
MSS
PWD
tPSKCD
JHS
2
2
2
2
ns
ns
ns
|tPLH − tPHL|
1
1
Data Rate Fast
Propagation Delay
Pulse Width
Pulse Width Distortion
Setup Time2
DRFAST
tPHL, tPLH
PW
PWD
MSSSETUP
JHS
2
26
34
26
Mbps
ns
ns
ns
ns
Within PWD limit
50% input to 50% output
Within PWD limit
21
1
21
100
1.5
12.5
10
3
3
|tPLH − tPHL|
Jitter, High Speed
SSA0, SSA1
1
ns
Data Rate Slow
Propagation Delay
Pulse Width
DRSLOW
tPHL, tPLH
PW
250
2.6
250
2.6
kbps
µs
µs
Within PWD limit
50% input to 50% output
Within PWD limit
0.1
4
0.1
4
Jitter, Low Speed
SSAx3 Minimum Input Skew4
JLS
tSSAx SKEW
2.5
2.5
µs
ns
3
40
40
1 Codirectional channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on the same side of the isolation barrier.
2
MSS
MSS
The
signal is glitch filtered in both speed grades, whereas the other fast signals are not glitch filtered in the B grade. To guarantee that
reaches the output
MSS
ahead of another fast signal, set up
prior to the competing signal by different times depending on speed grade.
3 SSAx = SSA0 or SSA1.
4 An internal asynchronous clock, not available to users, samples the low speed signals. If edge sequence in codirectional channels is critical to the end application, the
leading pulse must be at least 1 tSSAx SKEW ahead of a later pulse to guarantee the correct order or simultaneous arrival at the output.
Rev. B | Page 3 of 22
ADuM4154
Data Sheet
Table 3. For All Models1, 2, 3
Parameter
Symbol Min
Typ
Max
Unit
Test Conditions/Comments
SUPPLY CURRENT
A Grade and B Grade
IDD1
IDD2
IDD1
IDD2
4.8
6.5
10
8.5
13
18
19
mA
mA
mA
mA
CL = 0 pF, DRFAST = 1 MHz,
DRSLOW = 0 MHz
CL = 0 pF, DRFAST = 1 MHz,
DRSLOW = 0 MHz
CL = 0 pF, DRFAST = 17 MHz,
DRSLOW = 0 MHz
CL = 0 pF, DRFAST = 17 MHz,
DRSLOW = 0 MHz
B Grade
13.5
DC SPECIFICATIONS
MCLK, MSS, MO, SO, SSA0, SSA1
Input Threshold
Logic High
Logic Low
VIH
VIL
0.7 × VDDx
V
V
0.3 × VDDx
Input Hysteresis
VIHYST
II
500
+0.01 +1
mV
µA
Input Current per Channel
SCLK, MI, SI, SS0, SS1, SS2, SS3
Output Voltages
−1
0 V ≤ VINPUT ≤ VDDx
Logic High
VOH
VDDx − 0.1 5.0
VDDx − 0.4 4.8
V
V
V
V
V
IOUTPUT = −20 µA, VINPUT = VIH
IOUTPUT = −4 mA, VINPUT = VIH
IOUTPUT = 20 µA, VINPUT = VIL
IOUTPUT = 4 mA, VINPUT = VIL
Logic Low
VOL
0.0
0.2
0.1
0.4
2.6
VDD1, VDD2 Undervoltage Lockout
Supply Current per High Speed Channels
Dynamic Input
UVLO
IDDI(D)
IDDO(D)
0.080
0.046
mA/Mbps
mA/Mbps
Dynamic Output
Supply Current for All Low Speed Channels
Quiescent Input
Quiescent Output
IDD1(Q)
IDD2(Q)
4.2
6.1
mA
mA
AC SPECIFICATIONS
Output Rise/Fall Time
Common-Mode Transient Immunity4
tR/tF
|CM|
2.5
35
ns
kV/µs
10% to 90%
VINPUT = VDDx, VCM = 1000 V,
25
transient magnitude = 800 V
1 VDDx = VDD1 or VDD2
.
2
MSS
, MO, SO, SSA0, or SSA1 pins.
VINPUT is the input voltage of any of the MCLK,
3 IOUTPUT is the output current of any of the SCLK, MI, SI, SS0, SS1, SS2, or SS3 pins.
4 |CM| is the maximum common-mode voltage slew rate that can be sustained while maintaining output voltages within the VOH and VOL limits. The common-mode
voltage slew rates apply to both rising and falling common-mode voltage edges.
Rev. B | Page 4 of 22
Data Sheet
ADuM4154
ELECTRICAL CHARACTERISTICS—3.3 V OPERATION
All typical specifications are at TA = 25°C and VDD1 = VDD2 = 3.3 V. Minimum and maximum specifications apply over the entire
recommended operation range: 3.0 V ≤ VDD1 ≤ 3.6 V, 3.0 V ≤ VDD2 ≤ 3.6 V, and −40°C ≤ TA ≤ +125°C, unless otherwise noted.
Switching specifications are tested with CL = 15 pF and CMOS signal levels, unless otherwise noted.
Table 4. Switching Specifications
A Grade
B Grade
Parameter
Symbol Min Typ Max Min Typ Max Unit
Test Conditions/Comments
MCLK, MO, SO
SPI Clock Rate
SPIMCLK
DRFAST
tPHL, tPLH
PW
PWD
tPSKCD
JHS
1
2
30
12.5 MHz
Data Rate Fast (MO, SO)
Propagation Delay
Pulse Width
Pulse Width Distortion
Codirectional Channel Matching1
Jitter, High Speed
MSS
34
21
Mbps Within PWD limit
ns
ns
ns
ns
ns
50% input to 50% output
Within PWD limit
|tPLH − tPHL|
100
100
12.5
3
3
2
2
1
1
1
1
Data Rate Fast
Propagation Delay
Pulse Width
Pulse Width Distortion
Setup Time2
DRFAST
tPHL, tPLH
PW
PWD
MSSSETUP 1.5
JHS
2
34
34
34
Mbps Within PWD limit
ns
ns
ns
ns
ns
50% input to 50% output
Within PWD limit
|tPLH − tPHL
12.5
10
3
3
|
Jitter, High Speed
SSA0, SSA1
Data Rate Slow
Propagation Delay
Pulse Width
DRSLOW
tPHL, tPLH
PW
250
2.6
250
2.6
kbps
µs
µs
Within PWD limit
50% input to 50% output
Within PWD limit
0.1
4
0.1
4
Jitter, Low Speed
SSAx3 Minimum Input Skew4
JLS
tSSAx SKEW
2.5
2.5
µs
ns
3
40
40
1 Codirectional channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on the same side of the
isolation barrier.
2
MSS
MSS
reaches the
The
signal is glitch filtered in both speed grades, whereas the other fast signals are not glitch filtered in the B grade. To guarantee that
MSS
output ahead of another fast signal, set up
prior to the competing signal by different times depending on speed grade.
3 SSAx = SSA0 or SSA1.
4 An internal asynchronous clock, not available to users, samples the low speed signals. If edge sequence in codirectional channels is critical to the end
application, the leading pulse must be at least 1 tSSAx SKEW ahead of a later pulse to guarantee the correct order or simultaneous arrival at the output.
Rev. B | Page 5 of 22
ADuM4154
Data Sheet
Table 5. For All Models1, 2, 3
Parameter
Symbol Min
Typ
Max
Unit
Test Conditions/Comments
SUPPLY CURRENT
A Grade and B Grade
IDD1
IDD2
IDD1
IDD2
3.4
5
6.5
9
mA
mA
mA
mA
CL = 0 pF, DRFAST = 1 MHz,
DRSLOW = 0 MHz
CL = 0 pF, DRFAST = 1 MHz,
DRSLOW = 0 MHz
CL = 0 pF, DRFAST = 17 MHz,
DRSLOW = 0 MHz
CL = 0 pF, DRFAST = 17 MHz,
DRSLOW = 0 MHz
B Grade
11.7
10
15
14
DC SPECIFICATIONS
MCLK, MSS, MO, SO, SSA0, SSA1
Input Threshold
Logic High
Logic Low
VIH
VIL
0.7 × VDDx
V
V
0.3 × VDDx
Input Hysteresis
VIHYST
II
500
+0.01 +1
mV
µA
Input Current per Channel
SCLK, MI, SI, SS0, SS1, SS2, SS3
Output Voltages
−1
0 V ≤ VINPUT ≤ VDDx
Logic High
VOH
VDDx − 0.1 3.3
VDDx − 0.4 3.1
V
V
V
V
V
IOUTPUT = −20 µA, VINPUT = VIH
IOUTPUT = −4 mA, VINPUT = VIH
IOUTPUT = 20 µA, VINPUT = VIL
IOUTPUT = 4 mA, VINPUT = VIL
Logic Low
VOL
0.0
0.2
2.6
0.1
0.4
VDD1, VDD2 Undervoltage Lockout
Supply Current per High Speed Channel
Dynamic Input
UVLO
IDDI(D)
IDDO(D)
0.078
0.026
mA/Mbps
mA/Mbps
Dynamic Output
Supply Current for All Low Speed Channels
Quiescent Input
Quiescent Output
IDD1(Q)
IDD2(Q)
2.9
4.7
mA
mA
AC SPECIFICATIONS
Output Rise/Fall Time
Common-Mode Transient Immunity4
tR/tF
|CM|
2.5
35
ns
kV/µs
10% to 90%
VINPUT = VDDx, VCM = 1000 V,
25
transient magnitude = 800 V
1 VDDx = VDD1 or VDD2
.
2
MSS
, MO, SO, SSA0, or SSA1 pins.
VINPUT is the input voltage of any of the MCLK,
3 IOUTPUT is the output current of any of the SCLK, MI, SI, SS0 SS1, SS2, or SS3 pins.
4 |CM| is the maximum common-mode voltage slew rate that can be sustained while maintaining output voltages within the VOH and VOL limits. The common-mode
voltage slew rates apply to both rising and falling common-mode voltage edges.
Rev. B | Page 6 of 22
Data Sheet
ADuM4154
ELECTRICAL CHARACTERISTICS—MIXED 5 V/3.3 V OPERATION
All typical specifications are at TA = 25°C and VDD1 = 5 V, V DD2 = 3.3 V. Minimum and maximum specifications apply over the entire
recommended operation range: 4.5 V ≤ VDD1 ≤ 5.5 V, 3.0 V ≤ VDD2 ≤ 3.6 V, and −40°C ≤ TA ≤ +125°C, unless otherwise noted. Switching
specifications are tested with CL = 15 pF and CMOS signal levels, unless otherwise noted.
Table 6. Switching Specifications
A Grade
B Grade
Parameter
Symbol
Min Typ Max Min Typ Max Unit
Test Conditions/Comments
MCLK, MO, SO
SPI Clock Rate
SPIMCLK
DRFAST
tPHL, tPLH
PW
PWD
tPSKCD
JHS
1
2
27
15.6
34
17
MHz
Mbps Within PWD limit
Data Rate Fast (MO, SO)
Propagation Delay
Pulse Width
Pulse Width Distortion
Codirectional Channel Matching1
Jitter, High Speed
MSS
ns
ns
ns
ns
ns
50% input to 50% output
Within PWD limit
|tPLH − tPHL
25
12.5
2
2
2
2
|
1
1
1
1
Data Rate Fast
Propagation Delay
Pulse Width
Pulse Width Distortion
Setup Time2
DRFAST
tPHL, tPLH
PW
PWD
MSSSETUP
JHS
2
30
34
30
Mbps Within PWD limit
ns
ns
ns
ns
ns
50% input to 50% output
Within PWD limit
|tPLH − tPHL
25
12.5
10
2
2
|
1.5
Jitter, High Speed
SSA0, SSA1
Data Rate Slow
Propagation Delay
Pulse Width
DRSLOW
tPHL, tPLH
PW
250
2.6
250
2.6
kbps
µs
µs
Within PWD limit
50% input to 50% output
Within PWD limit
0.1
4
0.1
4
Jitter, Low Speed
SSAx3 Minimum Input Skew4
JLS
tSSAx SKEW
2.5
2.5
µs
ns
|tPLH − tPHL|
3
40
40
1 Codirectional channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on the same side of the isolation
barrier.
2
MSS
MSS
reaches the output
The
signal is glitch filtered in both speed grades, whereas the other fast signals are not glitch filtered in the B grade. To guarantee that
MSS
ahead of another fast signal, set up
prior to the competing signal by different times depending on speed grade.
3 SSAx = SSA0 or SSA1.
4 An internal asynchronous clock, not available to users, samples the low speed signals. If edge sequence in codirectional channels is critical to the end application, the
leading pulse must be at least 1 tSSAx SKEW ahead of a later pulse to guarantee the correct order or simultaneous arrival at the output.
Rev. B | Page 7 of 22
ADuM4154
Data Sheet
Table 7. For All Models1, 2, 3
Parameter
Symbol Min
Typ
Max
Unit
Test Conditions/Comments
SUPPLY CURRENT
A Grade and B Grade
IDD1
IDD2
IDD1
IDD2
4.8
5
8.5
9
mA
mA
mA
mA
CL = 0 pF, DRFAST = 1 MHz,
DRSLOW = 0 MHz
CL = 0 pF, DRFAST = 1 MHz,
DRSLOW = 0 MHz
CL = 0 pF, DRFAST = 17 MHz,
DRSLOW = 0 MHz
CL = 0 pF, DRFAST = 17 MHz,
DRSLOW = 0 MHz
B Grade
10
10
18
14
DC SPECIFICATIONS
MCLK, MSS, MO, SO, SSA0, SSA1
Input Threshold
Logic High
Logic Low
Input Hysteresis
Input Current per Channel
SCLK, MI, SI, SS0, SS1, SS2, SS3
Output Voltages
VIH
VIL
VIHYST
II
0.7 × VDDx
V
V
mV
µA
0.3 × VDDx
+1
500
+0.01
−1
0 V ≤ VINPUT ≤ VDDX
Logic High
VOH
VDDx − 0.1 VDDx
VDDx − 0.4 VDDx – 2.0
V
V
V
V
V
IOUTPUT = −20 µA, VINPUT = VIH
IOUTPUT = −4 mA, VINPUT = VIH
IOUTPUT = 20 µA, VINPUT = VIL
IOUTPUT = 4 mA, VINPUT = VIL
Logic Low
VOL
0.0
0.2
2.6
0.1
0.4
VDD1, VDD2 Undervoltage Lockout
Supply Current for All Low Speed Channels
Quiescent Input
UVLO
IDD1(Q)
IDD2(Q)
4.2
4.7
mA
mA
Quiescent Output
AC SPECIFICATIONS
Output Rise/Fall Time
Common-Mode Transient Immunity4
tR/tF
|CM|
2.5
35
ns
10% to 90%
25
kV/µs VINPUT = VDDx, VCM = 1000 V,
transient magnitude = 800 V
1 VDDx = VDD1 or VDD2
.
2
MSS
, MO, SO, SSA0, or SSA1 pins.
VINPUT is the input voltage of any of the MCLK,
3 IOUTPUT is the output current of any of the SCLK, MI, SI, SS0, SS1, SS2, or SS3 pins.
4 |CM| is the maximum common-mode voltage slew rate that can be sustained while maintaining output voltages within the VOH and VOL limits. The common-mode
voltage slew rates apply to both rising and falling common-mode voltage edges.
Rev. B | Page 8 of 22
Data Sheet
ADuM4154
ELECTRICAL CHARACTERISTICS—MIXED 3.3 V/5 V OPERATION
All typical specifications are at TA = 25°C and VDD1 = 3.3 V, V DD2 = 5 V. Minimum and maximum specifications apply over the entire
recommended operation range: 3.0 V ≤ VDD1 ≤ 3.6 V, 4.5 V ≤ VDD2 ≤ 5.5 V, and −40°C ≤ TA ≤ +125°C, unless otherwise noted. Switching
specifications are tested with CL = 15 pF and CMOS signal levels, unless otherwise noted.
Table 8. Switching Specifications
A Grade
B Grade
Parameter
Symbol
Min Typ Max Min Typ Max Unit
Test Conditions/Comments
MCLK, MO, SO
SPI Clock Rate
SPIMCLK
DRFAST
tPHL, tPLH
PW
PWD
tPSKCD
JHS
1
2
28
15.6
34
17
MHz
Mbps Within PWD limit
Data Rate Fast (MO, SO)
Propagation Delay
Pulse Width
Pulse Width Distortion
Codirectional Channel Matching1
Jitter, High Speed
MSS
ns
ns
ns
ns
ns
50% input to 50% output
Within PWD limit
|tPLH − tPHL
100
12.5
2
2
2
2
|
1
1
1
Jitter
1
ns
Data Rate Fast
Propagation Delay
Pulse Width
Pulse Width Distortion
Setup Time2
DRFAST
tPHL, tPLH
PW
PWD
MSSSETUP
JHS
2
28
34
28
Mbps Within PWD limit
21
ns
ns
ns
ns
ns
50% input to 50% output
Within PWD limit
|tPLH − tPHL
100
1.5
12.5
10
2
2
|
Jitter, High Speed
SSA0, SSA1
1
1
Data Rate Slow
Propagation Delay
Pulse Width
DRSLOW
tPHL, tPLH
PW
250
2.6
250
2.6
kbps
µs
µs
Within PWD limit
50% input to 50% output
Within PWD limit
0.1
4
0.1
4
Jitter, Low Speed
SSAx3 Minimum Input Skew4
JLS
tSSAx SKEW
2.5
2.5
µs
ns
|tPLH − tPHL|
3
40
40
1 Codirectional channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on the same side of the isolation
barrier.
2
MSS
MSS
reaches the output
The
signal is glitch filtered in both speed grades, whereas the other fast signals are not glitch filtered in the B grade. To guarantee that
MSS
ahead of another fast signal, set up
prior to the competing signal by different times depending on speed grade.
3 SSAx = SSA0 or SSA1.
4 An internal asynchronous clock, not available to users, samples the low speed signals. If edge sequence in codirectional channels is critical to the end application, the
leading pulse must be at least 1 tSSAx SKEW ahead of a later pulse to guarantee the correct order or simultaneous arrival at the output.
Rev. B | Page 9 of 22
ADuM4154
Data Sheet
Table 9. For All Models1, 2, 3
Parameter
Symbol Min
Typ
Max
Unit
Test Conditions/Comments
SUPPLY CURRENT
A Grade and B Grade
IDD
3.4
6.5
13
15
19
mA
mA
mA
mA
CL = 0 pF, DRFAST = 1 MHz,
DRSLOW = 0 MHz
CL = 0 pF, DRFAST = 1 MHz,
DRSLOW = 0 MHz
CL = 0 pF, DRFAST = 17 MHz,
DRSLOW = 0 MHz
CL = 0 pF, DRFAST = 17 MHz,
DRSLOW = 0 MHz
IDD2
IDD
6.5
B Grade
11.7
13.5
IDD2
DC SPECIFICATIONS
MCLK, MSS, MO, SO, SSA0, SSA1
Input Threshold
Logic High
Logic Low
Input Hysteresis
Input Current per Channel
SCLK, MI, SI, SS0, SS1, SS2, SS3
Output Voltages
VIH
VIL
VIHYST
II
0.7 × VDDx
V
V
mV
µA
0.3 × VDDx
+1
500
+0.01
−1
0 V ≤ VINPUT ≤ VDDx
Logic High
VOH
VDDx − 0.1 VDDx
VDDx − 0.4 VDDx – 2.0
V
V
V
V
V
IOUTPUT = −20 µA, VINPUT = VIH
IOUTPUT = −4 mA, VINPUT = VIH
IOUTPUT = 20 µA, VINPUT = VIL
IOUTPUT = 4 mA, VINPUT = VIL
Logic Low
VOL
0.0
0.2
2.6
0.1
0.4
VDD1, VDD2 Undervoltage Lockout
Supply Current for All Low Speed Channels
Quiescent Input
UVLO
IDD1Q)
IDD2(Q)
2.9
6.1
mA
mA
Quiescent Output
AC SPECIFICATIONS
Output Rise/Fall Time
Common-Mode Transient Immunity4
tR/tF
|CM|
2.5
35
ns
10% to 90%
25
kV/µs VINPUT = VDDx, VCM = 1000 V,
transient magnitude = 800 V
1 VDDx = VDD1 or VDD2
.
2
MSS
, MO, SO, SSA0, or SSA1 pins.
VINPUT is the input voltage of any of the MCLK,
3 IOUTPUT is the output current of any of the SCLK, MI, SI, SS0, SS1, SS2, or SS3 pins.
4 |CM| is the maximum common-mode voltage slew rate that can be sustained whereas maintaining output voltages within the VOH and VOL limits. The common-mode
voltage slew rates apply to both rising and falling common-mode voltage edges.
PACKAGE CHARACTERISTICS
Table 10.
Parameter
Symbol Min Typ Max Unit Test Conditions/Comments
Resistance (Input to Output)1
Capacitance (Input to Output)1
Input Capacitance2
RI-O
CI-O
CI
1012
1.0
4.0
46
Ω
pF
pF
f = 1 MHz
IC Junction to Ambient Thermal Resistance θJA
°C/W Thermocouple located at center of package underside
1 The device is considered a 2-terminal device: Pin 1 through Pin 10 are shorted together, and Pin 11 through Pin 20 are shorted together.
2 Input capacitance is from any input data pin to ground.
Rev. B | Page 10 of 22
Data Sheet
ADuM4154
REGULATORY INFORMATION
The ADuM4154 is approved and pending approval by the organizations listed in Table 11. See Table 16 and the Insulation Lifetime
section for recommended maximum working voltages for specific cross isolation waveforms and insulation levels.
Table 11.
UL
CSA
VDE
Recognized Under UL 1577
Approved under CSA Component Acceptance
Notice #5A
Certified according to DIN V VDE V 0884-10
(VDE V 0884-10):2006-122
Component Recognition Program1
5000 V rms Single Protection
Basic insulation per CSA 60950-1-07+A1+A2 and
IEC 60950-12nd Ed+A1+A2., 800 V rms (1131 V
peak) maximum working voltage3
Reinforced insulation, 849 V peak
CSA 60950-1-07+A1+A2 and IEC 60950-1 2nd
Ed.+A1+A2, 400 V rms (565 V peak) maximum
working voltage
Reinforced insulation (2MOPP) per IEC 60601-1
Ed.3.1, 250 V rms (353 V peak) maximum working
File E214100
File 205078
File 2471900-4880-0001
1 In accordance with UL 1577, each ADuM4154 is proof tested by applying an insulation test voltage ≥ 6000 V rms for 1 second (current leakage detection limit = 5 µA).
2 In accordance with DIN V VDE V 0884-10, each ADuM4154 is proof tested by applying an insulation test voltage ≥ 1590 V peak for 1 second (partial discharge
detection limit = 5 pC). The asterisk (*) marked on the component designates DIN V VDE V 0884-10 approval.
3 Use at working voltages above 400 VAC RMS shortens lifetime of the isolator significantly. See Table 16 for recommended maximum working voltages under ac and dc conditions.
INSULATION AND SAFETY RELATED SPECIFICATIONS
Table 12.
Parameter
Symbol Value Unit
Test Conditions/Comments
Rated Dielectric Insulation Voltage
Minimum External Air Gap (Clearance)
5000
8.3
V rms
1 minute duration
L(I01)
L(I02)
mm min Measured from input terminals to output terminals,
shortest distance through air
mm min Measured from input terminals to output terminals,
shortest distance path along body
Minimum External Tracking (Creepage)
Minimum Internal Gap (Internal Clearance)
8.3
0.017 mm min Distance through insulation
Tracking Resistance (Comparative Tracking Index) CTI
Material Group
>400
II
V
DIN IEC 112/VDE 0303 Part 1
Material group (DIN VDE 0110, 1/89, Table 1)
Rev. B | Page 11 of 22
ADuM4154
Data Sheet
DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 INSULATION CHARACTERISTICS
This isolator is suitable for reinforced electrical isolation only within the safety limit data. Maintenance of the safety data is ensured by
protective circuits. The asterisk (*) marked on packages denotes DIN V VDE V 0884-10 approval.
Table 13.
Description
Test Conditions/Comments
Symbol Characteristic Unit
Installation Classification per DIN VDE 0110
For Rated Mains Voltage ≤ 150 V rms
For Rated Mains Voltage ≤ 300 V rms
For Rated Mains Voltage ≤ 400 V rms
Climatic Classification
Pollution Degree per DIN VDE 0110, Table 1
Maximum Working Insulation Voltage
Input-to-Output Test Voltage, Method b1
I to IV
I to III
I to II
40/105/21
2
VIORM
Vpd(m)
849
1592
V peak
V peak
VIORM × 1.875 = Vpd(m), 100% production test,
t
ini = tm = 1 sec, partial discharge < 5 pC
Input-to-Output Test Voltage, Method a
After Environmental Tests Subgroup 1
VIORM × 1.5 = Vpd(m), tini = 60 sec, tm = 10 sec,
partial discharge < 5 pC
VIORM × 1.2 = Vpd(m), tini = 60 sec, tm = 10 sec,
partial discharge < 5 pC
Vpd(m)
Vpd(m)
1274
1019
V peak
V peak
After Input and/or Safety Test Subgroup 2
and Subgroup 3
Highest Allowable Overvoltage
Surge Isolation Voltage
VIOTM
VIOSM
6000
6250
V peak
V peak
VIOSM(TEST) = 10 kV, 1.2 µs rise time, 50 µs,
50% fall time
Safety Limiting Values
Maximum value allowed in the event of a failure
(see Figure 2)
Case Temperature
Safety Total Dissipated Power
Insulation Resistance at TS
TS
PS
RS
135
2.4
>109
°C
W
Ω
VIO = 500 V
3.0
2.5
2.0
1.5
1.0
0.5
0
RECOMMENDED OPERATING CONDITIONS
Table 14.
Parameter
Symbol
Value
−40°C to +125°C
Operating Temperature Range
Supply Voltage Range1
Input Signal Rise and Fall Times
TA
VDD1, VDD2 3.0 V to 5.5 V
1.0 ms
1 See the DC Correctness and Magnetic Field Immunity section for information
on the immunity to the external magnetic fields.
0
50
100
150
AMBIENT TEMPERATURE (°C)
Figure 2. Thermal Derating Curve, Dependence of Safety Limiting Values
with Case Temperature per DIN V VDE V 0884-10
Rev. B | Page 12 of 22
Data Sheet
ADuM4154
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 16. Maximum Continuous Working Voltage1
Parameter
Max
Constraint
Table 15.
Parameter
60 Hz AC Voltage
400 V rms
20-year lifetime at 0.1%
failure rate, zero average
voltage
Limited by the creepage
of the package,
Rating
Storage Temperature (TST) Range
Ambient Operating Temperature
(TA) Range
Supply Voltages (VDD1, VDD2
Input Voltages (MCLK, MSS, MO, SO,
SSA0, SSA1)
Output Voltages (SCLK, MI, SI, SS0
SS1, SS2, SS3)
Average Output Current per Pin1
Common-Mode Transients2
−65°C to +150°C
−40°C to +125°C
DC Voltage
1173 V peak
)
−0.5 V to +7.0 V
−0.5 V to VDDx + 0.5 V
Pollution Degree 2,
Material Group II2, 3
1 See the Insulation Lifetime section for details.
−0.5 V to VDDx + 0.5 V
2 Other pollution degree and material group requirements yield a different limit.
3 Some system level standards allow components to use the printed wiring
board (PWB) creepage values. The supported dc voltage may be higher for
those standards.
−10 mA to +10 mA
−100 kV/µs to +100 kV/µs
1 See Figure 2 for maximum safety rated current values across temperature.
2 Refers to common-mode transients across the insulation barrier. Common-
mode transients exceeding the absolute maximum ratings may cause
latch-up or permanent damage.
ESD CAUTION
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
Rev. B | Page 13 of 22
ADuM4154
Data Sheet
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
V
1
2
3
4
5
6
7
8
9
V
DD2
20
19
18
17
16
15
DD1
GND
GND
2
1
MCLK
MO
SCLK
SI
ADuM4154
TOP VIEW
(Not to Scale)
MI
SO
MSS
SSA0
SSA1
NIC
SS0
14 SS1
13
12
11
SS2
SS3
GND
GND 10
1
2
NOTES
1. NIC = NOT INTERNALLY CONNECTED. THIS PIN
IS NOT INTERNALLY CONNECTED AND SERVES
NO FUNCTION IN THE ADuM4154.
Figure 3. Pin Configuration
Table 17. Pin Function Descriptions
Pin No. Mnemonic Direction Description
1
2, 10
3
4
5
6
VDD1
GND1
MCLK
MO
MI
MSS
Power
Return
Input
Input
Output
Input
Input Power Supply for Isolator Side 1. A bypass capacitor from VDD1 to GND1 to local ground is required.
Ground 1. Ground reference for Isolator Side 1.
SPI Clock from the Master Controller.
SPI Data from the Master to the Slave MO/SI Line.
SPI Data from the Slave to the Master MI/SO Line.
Slave Select from the Master. This signal uses an active low logic. The slave select pin can require as
much as a 10 ns setup time from the next clock or data edge depending on the speed grade.
7
8
9
SSA0
SSA1
NIC
GND2
SS3
SS2
SS1
SS0
SO
Input
Input
Multiplexer Selection Input, Low Order Bit.
Multiplexer Selection Input, High Order Bit.
Not Internally Connected. This pin is not internally connected and serves no function in the ADuM4154.
Ground 2. Ground reference for Isolator Side 2.
Routed Slave Select Signal 3. High-Z when SS3 is not selected.
Routed Slave Select Signal 2. High-Z when SS2 is not selected.
Routed Slave Select Signal 1. High-Z when SS1 is not selected.
Routed Slave Select Signal 0. High-Z when SS0 is not selected.
SPI Data from the Slave to the Master MI/SO Line.
11, 19
12
13
14
15
16
17
18
20
Return
Output
Output
Output
Output
Input
Output
Output
Power
SI
SCLK
VDD2
SPI Data from the Master to the Slave MO/SI Line.
SPI Clock from the Master Controller.
Input Power Supply for Isolator Side 2. A bypass capacitor from VDD2 to GND2 to local ground is required.
Rev. B | Page 14 of 22
Data Sheet
ADuM4154
Table 18. Multiplexer Select Truth Table1
Master Mux Inputs
Slave Mux Outputs
MSS
SSA0
SSA1
SS0
1
0
Z
Z
Z
Z
Z
Z
SS1
Z
Z
1
0
Z
Z
Z
Z
SS2
Z
Z
Z
Z
1
0
Z
Z
SS3
Z
Z
Z
Z
Z
Z
1
0
1
0
1
0
1
0
1
0
0
0
1
1
0
0
1
1
0
0
0
0
1
1
1
1
1 Z = high impedance.
Table 19. Power Off Default State Truth Table (Positive Logic)1, 2
Master Side
Slave Side
Power State
VDD1
Unpowered3
Powered
Powered
Powered
Output
Inputs
Power State
Input
Outputs
MI
Z
Z
1
0
MCLK
MO
X
X
1
0
VDD2
SO
X
X
1
0
SCLK
SI
Z
Z
1
X
X
1
0
Powered
Unpowered3
Powered
Powered
Z
Z
1
0
0
1 Z = high impedance.
2 X = irrelevant.
3 Outputs on an unpowered side are high impedance within one diode drop of ground.
Rev. B | Page 15 of 22
ADuM4154
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
7
6
5
5.0V
5.0V
3.3V
4
3
2
1
0
3.3V
0
20
40
DATA RATE (Mbps)
60
80
0
20
40
DATA RATE (Mbps)
60
80
Figure 4. Typical Dynamic Supply Current per Input Channel vs. Data Rate for
5.0 V and 3.3 V Operation
Figure 7. Typical Dynamic Supply Current per Output Channel vs. Data Rate
for 5.0 V and 3.3 V Operation
30
25
25
20
5.0V
20
5.0V
15
3.3V
3.3V
15
10
5
10
5
0
0
0
20
40
60
80
0
20
40
60
80
DATA RATE (Mbps)
DATA RATE (Mbps)
Figure 5. Typical IDD1 Supply Current vs. Data Rate for
5.0 V and 3.3 V Operation
Figure 8. Typical IDD2 Supply Current vs. Data Rate for
5.0 V and 3.3 V Operation
16
14
12
10
8
25
20
15
10
5
3.3V
5.0V
3.3V
5.0V
6
4
2
0
–40
0
–40
10
60
110
10
60
110
AMBIENT TEMPERATURE (°C)
AMBIENT TEMPERATURE (°C)
Figure 6. Typical Propagation Delay vs. Ambient Temperature for High Speed
Channels Without Glitch Filter (See the High Speed Channels Section)
Figure 9. Typical Propagation Delay vs. Ambient Temperature for High Speed
Channels with Glitch Filter (See the High Speed Channels Section)
Rev. B | Page 16 of 22
Data Sheet
ADuM4154
APPLICATIONS INFORMATION
(slave select bar) is typically an active low signal. can have
SS
SS
INTRODUCTION
many different functions in SPI and SPI like busses. Many of
these functions are edge triggered; therefore, the path contains a
SS
glitch filter in both the A grade and the B grade. The glitch filter
prevents short pulses from propagating to the output or causing
The ADuM4154 was created to optimize isolation of the SPI for
speed and to provide additional low speed channels for control
and status monitoring functions. The isolator is based on
differential signaling iCoupler technology for enhanced speed
and noise immunity.
MSS
other errors in operation. The
signal requires a 10 ns setup
time in the B grade devices prior to the first active clock edge to
allow the added propagation time of the glitch filter.
High Speed Channels
The ADuM4154 has four high speed channels. The first three
channels, CLK, MI/SO, and MO/SI (the slash indicates the
connection of the particular input and output channel across
the isolator), are optimized for either low propagation delay in
the B grade, or high noise immunity in the A grade. The
difference between the grades is the addition of a glitch filter to
these three channels in the A grade version, which increases the
propagation delay. The B grade version, with a maximum
propagation delay of 14 ns, supports a maximum clock rate of
17 MHz in standard 4-wire SPI. However, because the glitch
filter is not present in the B grade version, ensure that spurious
glitches of less than 10 ns are not present.
Slave Select Multiplexer
The ADuM4154 can control up to four independent slave
devices. Figure 10 shows how this can be done using general-
purpose isolators. An isolation channel is required for each
slave select; therefore, seven high speed channels are required to
transfer bidirectional data to four slaves.
MASTER
ISOLATOR
CLK
SLAVE 0
SLAVE 1
SLAVE 2
SLAVE 3
CLK
MOSI
MISO
MOSI
MISO
Glitches of less than 10 ns in the B grade devices can cause the
second edge of the glitch to be missed. This pulse condition is
then seen as a spurious data transition on the output that is
corrected by a refresh or the next valid data edge. It is recommended
to use the A grade devices in noisy environments.
SS0
SS0
CLK
SS1
SS2
SS3
MOSI
MISO
SS1
The relationship between the SPI signal paths and the pin
mnemonics of the ADuM4154 and data directions is detailed in
Table 20.
CLK
Table 20. Pin Mnemonics Correspondence to SPI Signal Path
Names
MOSI
MISO
SPI Signal
Path
Master
Side 1
Data
Direction
Slave
Side 2
SS2
CLK
MCLK
MO
MI
SCLK
SI
SO
→
→
←
→
CLK
MO/SI
MI/SO
SS
MOSI
MISO
MSS
SSx
SS3
The datapaths are SPI mode agnostic. The CLK and MO/SI SPI
datapaths are optimized for propagation delay and channel to
channel matching. The MI/SO SPI datapath is optimized for
propagation delay. The device does not synchronize to the clock
channel; therefore, there are no constraints on the clock polarity
or the timing with respect to the data line. To allow
Figure 10. Multiple Slave Control with Standard Isolators
compatibility with nonstandard SPI interfaces, the MI pin is
always active, and does not tristate when the slave select is not
asserted. This precludes tying several MI lines together without
adding a trisate buffer or multiplexor.
Rev. B | Page 17 of 22
ADuM4154
Data Sheet
Figure 11 shows how the ADuM4154 can control up to four
Figure 12 illustrates the behavior of the SSA0 and SSA1
MSS
MSS
slaves by routing the
input to one of four outputs on the
channels. This diagram assumes that
SS1, SS2, and SS3 are pulled up.
is low and that SS0,
slave side of the isolator, which eliminates three isolation
channels compared to the standard solution.
SAMPLE CLOCK
MASTER
ADuM4154
SCLK
SI
MCLK
CLK
SLAVE 0
SLAVE 1
SLAVE 2
SLAVE 3
CLK
SSA0
SSA1
A
B
MO
MI
MOSI
MISO
MOSI
MISO
SO
A
C
MSS
MSS
SS
SS0
SS1
SS2
SS3
SSA0
SSA1
CLK
MOSI
MISO
SS
ADDRESS0
ADDRESS1
SS0
MUX
C
SS1
SS2
A
SS3
B
CLK
MOSI
MISO
OUTPUT CLOCK
Figure 12. Mux Select Timing
SS
The following details the mux select timing shown in Figure 12:
CLK
•
Point A: The mux select lines must be switched
simultaneously to within the tSSAx SKEW time. Failure to do
this may allow sampling the inputs between the edges and
selecting an incorrect mux output. Point A on SS1 is a
metastable state on the output mux resulting from wide
spacing between SSA0 and SSA1.
MOSI
MISO
SS
Figure 11. Multiple Slave Control
•
•
Point B: For mux select lines to be processed predictably, a
state of SSA0 and SSA1 must be stable for longer than 4 µs
before switching the mux to another output. This
guarantees that at least two samples are taken of the inputs
before the mux output is changed.
Point C: This point in Figure 12 shows a clean transfer
between SS3 being active and SS0 being active. The mux
was designed to eliminate any short duration metastable
states between any two selected outputs.
The multiplexer select lines are low speed channels implemented as
part of the dc correctness scheme in the ADuM4154. The dc
value of all high and low speed inputs on a given side of the
device are sampled simultaneously, packetized, and shifted
across an isolation coil. The high speed channels are compared
for dc accuracy, and the low speed mux select lines, SSA0 and
SSA1, are transferred to the mux control block. The dc
correctness data for the high speed channels is handled
internally with no visibility off chip.
This data is regulated by a free running internal clock. Because data
is sampled at discrete times based on this clock, the propagation
delay for mux select lines is between 0.1 µs and 2.6 µs, depending
on where the input data edge changes with respect to the internal
sample clock. After an address propagation delay time of up to
MSS
2.6 µs, the multiplexer routes the
signals to the desired output.
The outputs that are not selected are set to high-Z, and the
application pulls them to the desired idle state.
Rev. B | Page 18 of 22
Data Sheet
ADuM4154
PRINTED CIRCUIT BOARD (PCB) LAYOUT
DC CORRECTNESS AND MAGNETIC FIELD
IMMUNITY
The ADuM4154 digital isolator requires no external interface
circuitry for the logic interfaces. Power supply bypassing is
strongly recommended at both the VDD1 and VDD2 supply pins
(see Figure 13). The capacitor value must be between 0.01 µF
and 0.1 µF. The total lead length between both ends of the
capacitor and the input power supply pin must not exceed
20 mm.
Positive and negative logic transitions at the isolator input cause
narrow (~1 ns) pulses to be sent via the transformer to the
decoder. The decoder is bistable and is, therefore, either set or
reset by the pulses indicating input logic transitions. In the
absence of logic transitions at the input for more than ~1.2 µs, a
periodic set of refresh pulses indicative of the correct input state
are sent via the low speed channel to ensure dc correctness at
the output.
BYPASS < 10mm
V
V
DD2
DD1
GND
2
GND
If the low speed decoder receives no pulses for more than about
5 µs, the input side is assumed to be unpowered or nonfunctional,
in which case, the isolator output is forced to a high-Z state by
the watchdog timer circuit.
1
SCLK
SI
MCLK
MO
ADuM4154
TOP VIEW
(Not to Scale)
SO
MI
MSS
SSA0
SS0
SS1
SS2
SS3
The limitation on the magnetic field immunity of the device is
set by the condition in which induced voltage in the transformer
receiving coil is sufficiently large to either falsely set or reset the
decoder. The following analysis defines such conditions. The
ADuM4154 is examined in a 3 V operating condition because it
represents the most susceptible mode of operation for this
product.
SSA1
NIC
GND
2
GND
1
Figure 13. Recommended PCB Layout
In applications involving high common-mode transients, it is
important to minimize board coupling across the isolation barrier.
Furthermore, design the PCB layout so that any coupling that
does occur affects all pins equally on a given component side.
Failure to ensure this may cause voltage differentials between
pins that exceed the absolute maximum ratings of the device,
thereby leading to latch-up or permanent damage.
The pulses at the transformer output have an amplitude greater
than 1.5 V. The decoder has a sensing threshold of about 1.0 V;
thereby establishing a 0.5 V margin in which induced voltages
can be tolerated. The voltage induced across the receiving coil is
given by
PROPAGATION DELAY RELATED PARAMETERS
2
V = (−dβ/dt)Σπrn ; n = 1, 2, …, N
Propagation delay is a parameter that describes the time it takes
a logic signal to propagate through a component. The input to
output propagation delay time for a high to low transition may
differ from the propagation delay time of a low to high
transition.
where:
β is the magnetic flux density.
rn is the radius of the nth turn in the receiving coil.
N is the number of turns in the receiving coil.
Given the geometry of the receiving coil in the ADuM4154 and
an imposed requirement that the induced voltage be, at most,
50% of the 0.5 V margin at the decoder, a maximum allowable
magnetic field is calculated, as shown in Figure 15.
100
INPUT
50%
tPLH
tPHL
OUTPUT
50%
Figure 14. Propagation Delay Parameters
10
1
Pulse width distortion is the maximum difference between
these two propagation delay values and an indication of how
accurately the timing of the input signal is preserved.
Channel to channel matching refers to the maximum amount
the propagation delay differs between channels within a single
ADuM4154 component.
0.1
0.01
0.001
1k
100M
10k
100k
1M
10M
MAGNETIC FIELD FREQUENCY (Hz)
Figure 15. Maximum Allowable External Magnetic Flux Density
Rev. B | Page 19 of 22
ADuM4154
Data Sheet
For example, at a magnetic field frequency of 1 MHz, the
maximum allowable magnetic field of 0.5 kgauss induces a
voltage of 0.25 V at the receiving coil. This voltage is about 50%
of the sensing threshold and does not cause a faulty output
transition. If such an event occurs, with the worst-case polarity,
during a transmitted pulse, the interference reduces the received
pulse from >1.0 V to 0.75 V. This voltage is still well above the
0.5 V sensing threshold of the decoder.
These quiescent currents add to the high speed current as is
shown in the following equations for the total current for each
side of the isolator. Dynamic currents are taken from Table 3
and Table 5 for the respective voltages.
For Side 1, the supply current is given by
I
DD1 = IDDI(D) × (fMCLK + fMO + fMSS) + fMI ×
(IDDO(D) + ((0.5 × 10−3) × CL(MI) × VDD1)) + IDD1(Q)
For Side 2, the supply current is given by
The preceding magnetic flux density values correspond to
specific current magnitudes at given distances away from the
ADuM4154 transformers. Figure 16 expresses these allowable
current magnitudes as a function of frequency for selected
distances. The ADuM4154 is insensitive to external fields. Only
extremely large, high frequency currents very close to the
component are potentially a concern. For the 1 MHz example
noted, placing a 1.2 kA current 5 mm away from the
ADuM4154 affects component operation.
I
DD2 = IDDI(D) × fSO
SCLK × (IDDO(D) +((0.5 × 10−3) × CL(SCLK) × VDD2)) +
fSI × (IDDO(D) +((0.5 × 10−3) × CL(SI) × VDD2)) +
SSx × (IDDO(D) +((0.5 × 10−3) × CL(SSx) × VDD2)) + IDD2(Q)
where:
DDI(D), IDDO(D) are the input and output dynamic supply currents
+
f
f
I
per channel (mA/Mbps).
fx is the logic signal data rate for the specified channel (Mbps).
1000
I
DD1(Q), IDD2(Q) are the specified Side 1 and Side 2 quiescent
supply currents (mA).
L(x) is the load capacitance of the specified output (pF).
DDx is the supply voltage of the side being evaluated (V).
DISTANCE = 1m
100
C
V
10
Figure 4 and Figure 7 show the typical supply current per
channel as a function of data rate for an input and unloaded
output. Figure 5 and Figure 8 show the total IDD1 and IDD2 supply
currents as a function of data rate for ADuM4154 channel
configurations with all high speed channels running at the same
speed and the low speed channels at idle.
DISTANCE = 100mm
1
DISTANCE = 5mm
0.1
INSULATION LIFETIME
0.01
1k
10k
100k
1M
10M
100M
All insulation structures eventually break down when subjected
to voltage stress over a sufficiently long period. The rate of
insulation degradation is dependent on the characteristics of the
voltage waveform applied across the insulation, as well as the
materials and material interfaces.
MAGNETIC FIELD FREQUENCY (Hz)
Figure 16. Maximum Allowable Current for
Various Current to ADuM4154 Spacings
At combinations of a strong magnetic field and high frequency,
any loops formed by the PCB traces may induce sufficiently
large error voltages to trigger the thresholds of succeeding
circuitry. Take care to avoid PCB structures that form loops.
Two types of insulation degradation are of primary interest:
breakdown along surfaces exposed to the air and insulation
wear out. Surface breakdown is the phenomenon of surface
tracking and the primary determinant of surface creepage
requirements in system level standards. Insulation wear out is
the phenomenon where charge injection or displacement
currents inside the insulation material cause long-term
insulation degradation.
POWER CONSUMPTION
The supply current at a given channel of the ADuM4154
isolator is a function of the supply voltage, the data rate of the
channel, the output load of the channel, and whether it is a high
or low speed channel.
The low speed channels draw a constant quiescent current
caused by the internal ping-pong datapath. The operating
frequency is low enough that the capacitive losses caused by
the recommended capacitive load are negligible compared to
the quiescent current. The explicit calculation for the data rate
is eliminated for simplicity, and the quiescent current for each
side of the isolator due to the low speed channels can be found
in Table 3, Table 5, Table 7, and Table 9 for the particular operating
voltages.
Rev. B | Page 20 of 22
Data Sheet
ADuM4154
Surface Tracking
Calculation and Use of Parameters Example
Surface tracking is addressed in electrical safety standards by
setting a minimum surface creepage based on the working
voltage, the environmental conditions, and the properties of the
insulation material. Safety agencies perform characterization
testing on the surface insulation of components that allow the
components to be categorized in different material groups.
Lower material group ratings are more resistant to surface
tracking and, therefore, can provide adequate lifetime with
smaller creepage. The minimum creepage for a given working
voltage and material group is in each system level standard and
is based on the total rms voltage across the isolation, pollution
degree, and material group. The material group and creepage
for the ADuM4154 isolator are detailed in Table 12.
The following is an example that frequently arises in power
conversion applications. Assume that the line voltage on one
side of the isolation is 240 VAC RMS, and a 400 VDC bus voltage is
present on the other side of the isolation barrier. The isolator
material is polyimide. To establish the critical voltages in
determining the creepage clearance and lifetime of a device,
see Figure 17 and the following equations.
V
AC RMS
V
V
V
DC
PEAK
RMS
Insulation Wear Out
The lifetime of insulation caused by wear out is determined by
its thickness, the material properties, and the voltage stress
applied. It is important to verify that the product lifetime is
adequate at the application working voltage. The working
voltage supported by an isolator for wear out may not be the
same as the working voltage supported for tracking. It is the
working voltage applicable to tracking that is specified in most
standards.
TIME
Figure 17. Critical Voltage Example
The working voltage across the barrier from Equation 1 is
VRMS = VAC RMS2 +VDC
2
Testing and modeling have shown that the primary driver of
long-term degradation is displacement current in the polyimide
insulation causing incremental damage. The stress on the
insulation can be broken down into two broad categories, such
as dc stress, which causes very little wear out because there is no
displacement current, and an ac component time varying
voltage stress, which causes wear out.
VRMS = 2402 + 4002
VRMS = 466 V
The 466 V rms working voltage is used together with the
material group and pollution degree when looking up the
creepage required by a system standard.
To determine if the lifetime is adequate, obtain the time varying
portion of the working voltage. The ac rms voltage can be obtained
from Equation 2.
The ratings in certification documents are usually based on
60 Hz sinusoidal stress, because this reflects isolation from line
voltage. However, many practical applications have
combinations of 60 Hz ac and dc across the barrier, as shown in
Equation 1. Because only the ac portion of the stress causes
wear out, the equation can be rearranged to solve for the ac rms
voltage, as shown in Equation 2. For insulation wear out with
the polyimide materials used in this product, the ac rms voltage
determines the product lifetime.
2
VAC RMS = VRMS2 −VDC
VAC RMS
=
4662 − 4002
VAC RMS = 240 V
In this case, the VAC RMS is simply the line voltage of 240 VRMS
This calculation is more relevant when the waveform is not
sinusoidal. The value is compared to the limits for the working
voltage listed in Table 16 for the expected lifetime, less than a
60 Hz sine wave, and it is well within the limit for a 50-year
service life.
.
2
VRMS = VAC RMS2 +VDC
(1)
or
2
VAC RMS = VRMS2 −VDC
(2)
Note that the dc working voltage limit in Table 16 is set by the
creepage of the package as specified in IEC 60664-1. This value
may differ for specific system level standards.
where:
V
V
V
RMS is the total rms working voltage.
AC RMS is the time varying portion of the working voltage.
DC is the dc offset of the working voltage.
Rev. B | Page 21 of 22
ADuM4154
Data Sheet
OUTLINE DIMENSIONS
15.54
15.40
15.27
20
11
10
7.59
7.50
7.39
10.54
10.30
10.06
1
PIN 1
INDICATOR
TOP VIEW
SIDE VIEW
0.76
0.25
45°
0.25 BSC
2.64
2.50
2.36
2.44
2.24
GAGE
0.33
0.23
PLANE
END VIEW
0.25
0.10
SEATING
PLANE
8°
0°
1.27 BSC
COPLANARITY
0.48
0.36
0.89
0.65
0.41
0.10
COMPLIANT TO JEDEC STANDARDS MS-013-AD
Figure 18. 20-Lead Standard Small Outline Package, with Increased Creepage [SOIC_IC]
Wide Body
(RI-20-1)
Dimension shown in millimeters
ORDERING GUIDE
No. of
No. of
Inputs,
Maximum Maximum
Data Rate Propagation
Isolation
Rating
Inputs,
Temperature
Range
Package
Description
Package
Option
Model1, 2
VDD1 Side VDD2 Side (MHz)
Delay, 5 V (ns) (V rms)
ADuM4154ARIZ
ADuM4154ARIZ-RL
5
5
1
1
1
1
25
25
5000
−40°C to +125°C 20-Lead SOIC_IC RI-20-1
−40°C to +125°C 20-Lead SOIC_IC, RI-20-1
13” Tape and Reel
5000
ADuM4154BRIZ
5
5
1
1
17
17
14
14
−40°C to +125°C 20-Lead SOIC_IC RI-20-1
5000
5000
ADuM4154BRIZ-RL
−40°C to +125°C 20-Lead SOIC_IC, RI-20-1
13”Tape and Reel
EVAL-ADuM3154Z
Evaluation Board
1 Z = RoHS Compliant Part.
2 The EVAL-ADuM3154Z uses a functionally equivalent device for evaluation. The pad layout on the EVAL-ADuM3154Z evaluation board does not support the 20-lead
SOIC_IC package.
©2014–2017 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D12366-0-7/17(B)
Rev. B | Page 22 of 22
相关型号:
©2020 ICPDF网 联系我们和版权申明