ADXL202JE [ADI]
Low-Cost +-2 g Dual-Axis Accelerometer with Duty Cycle Output; 低成本+ -2克双轴加速度计与占空比输出
| 型号： | ADXL202JE |
| 厂家： | 
ADI |
| 描述： | Low-Cost +-2 g Dual-Axis Accelerometer with Duty Cycle Output |
| 文件： | 总12页 (文件大小：153K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Low-Cost ꢀ2 g Dual-Axis Accelerometer
a
with Duty Cycle Output
ADXL202E*
FEATURES
FUNCTIONAL BLOCK DIAGRAM
2-Axis Acceleration Sensor on a Single IC Chip
5 mm ꢃ 5 mm ꢃ 2 mm Ultrasmall Chip Scale Package
2 mg Resolution at 60 Hz
3V TO 5.25V
C
X
V
X
FILT
SELF-TEST
DD
Low-Power < 0.6 mA
Direct Interface to Low-Cost Microcontrollers via
Duty Cycle Output
BW Adjustment with a Single Capacitor
3 V to 5.25 V Single Supply Operation
1000 g Shock Survival
R
32kꢂ
X SENSOR
FILT
X
OUT
C
O
U
N
T
E
R
DEMOD
ANALOG
TO
DUTY
CYCLE
(ADC)
C
DC
OSCILLATOR
ꢁP
ADXL202E
DEMOD
R
32kꢂ
Y
FILT
OUT
APPLICATIONS
Y SENSOR
COM
Y
T2
R
FILT
2-Axis Tilt Sensing with Faster Response than
Electrolytic, Mercury, or Thermal Sensors
Computer Peripherals
C
Y
SET
Information Appliances
Alarms and Motion Detectors
Disk Drives
T2
T1
A(g) = (T1/T2 – 0.5)/12.5%
0g = 50% DUTY CYCLE
Vehicle Security
T2 = R
/125Mꢂ
SET
GENERAL DESCRIPTION
The typical noise floor is 200 g√Hz, allowing signals below
2 mg (at 60 Hz bandwidth) to be resolved.
The ADXL202E is a low-cost, low-power, complete 2-axis acceler-
ometer with a digital output, all on a single monolithic IC. It is an
improved version of the ADXL202AQC/JQC. The ADXL202E
will measure accelerations with a full-scale range of Ϯ2 g. The
ADXL202E can measure both dynamic acceleration (e.g., vibra-
tion) and static acceleration (e.g., gravity).
The bandwidth of the accelerometer is set with capacitors CX and
CY at the XFILT and YFILT pins. An analog output can be recon-
structed by filtering the duty cycle output.
The ADXL202E is available in 5 mm ϫ 5 mm ϫ 2 mm 8-lead
hermetic LCC package.
The outputs are analog voltage or digital signals whose duty cycles
(ratio of pulsewidth to period) are proportional to acceleration.
The duty cycle outputs can be directly measured by a micro-
processor counter, without an A/D converter or glue logic. The
duty cycle period is adjustable from 0.5 ms to 10 ms via a single
resistor (RSET).
*Patents Pending
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
Fax: 781/326-8703
World Wide Web Site: http://www.analog.com
© Analog Devices, Inc., 2000
(TA = TMIN to TMAX, TA = 25ꢄC for J Grade only, VDD = 5 V, RSET = 125 kꢂ,
Acceleration = 0 g, unless otherwise noted.)
ADXL202E–SPECIFICATIONS
TPC1
Graph Min
ADXL202JE
Typ
ADXL202AE
Typ
Parameter
Conditions
Max
Min
Max
Unit
SENSOR INPUT
Measurement Range2
Nonlinearity
Each Axis
2
2
g
Best Fit Straight Line
X Sensor to Y Sensor
0.2
1
0.01
2
0.2
1
0.01
2
% of FS
Degrees
Degrees
%
Alignment Error3
Alignment Error
Cross-Axis Sensitivity4
X
X
SENSITIVITY
Each Axis
Duty Cycle per g
Duty Cycle per g
Sensitivity XFILT, YFILT
Sensitivity XFILT, YFILT
Temperature Drift5
T1/T2, VDD = 5 V
T1/T2, VDD = 3 V
VDD = 5 V
VDD = 3 V
Delta from 25ЊC
X
X
X
X
X
10.5
9.0
265
140
12.5
11
312
167
0.5
14.5
13.0
360
195
10
12.5
11
312
167
0.5
15
%/g
%/g
mV/g
mV/g
%
8.5
250
140
13.5
375
200
ZERO g BIAS LEVEL
0 g Duty Cycle
0 g Duty Cycle
0 g Voltage XFILT, YFILT
0 g Voltage XFILT, YFILT
0 g Duty Cycle vs. Supply
0 g Offset vs. Temperature5
Each Axis
T1/T2, VDD = 5 V
T1/T2, VDD = 3 V
VDD = 5 V
X
X
X
X
X
X
34
31
2.1
1.2
50
50
2.5
1.5
1.0
2.0
66
69
2.9
1.8
4.0
30
31
2.0
1.2
50
50
2.5
1.5
1.0
2.0
70
69
3.0
1.8
4.0
%
%
V
V
%/V
mg/ЊC
VDD = 3 V
Delta from 25ЊC
@ 25ЊC
NOISE PERFORMANCE
Noise Density
X
200
200
1000
µg√Hz rms
FREQUENCY RESPONSE
3 dB Bandwidth
Sensor Resonant Frequency
At Pins XFILT, YFILT
6
10
6
10
kHz
kHz
FILTER
RFILT Tolerance
Minimum Capacitance
32 kΩ Nominal
15
10
15
10
%
pF
At Pins XFILT, YFILT
1000
0.7
1000
0.7
SELF-TEST
Duty Cycle Change
Self-Test “0” to “1”
%
DUTY CYCLE OUTPUT STAGE
FSET
Output High Voltage
Output Low Voltage
T2 Drift vs. Temperature
Rise/Fall Time
RSET = 125 kΩ
I = 25 µA
I = 25 µA
1.3
1.3
kHz
V
mV
ppm/ЊC
ns
VS – 200 mV
VS – 200 mV
200
200
50
200
50
200
POWER SUPPLY
Operating Voltage Range
Quiescent Supply Current
Turn-On Time
3
5.25
1.0
3.0
5.25
1.0
V
mA
ms
0.6
0.6
CFILT in µF
160 ϫ CFILT + 0.3
160 ϫ CFILT + 0.3
TEMPERATURE RANGE
Specified Performance AE
Operating Range
–40
–40
+85
+85
ЊC
ЊC
0
70
NOTES
1Typical Performance Characteristics.
2Guaranteed by measurement of initial offset and sensitivity.
3Alignment error is specified as the angle between the true and indicated axis of sensitivity (see TPC 15).
4Cross-axis sensitivity is the algebraic sum of the alignment and the inherent sensitivity errors.
5Defined as the output change from ambient to maximum temperature or ambient to minimum temperature.
Specifications subject to change without notice.
–2–
REV. A
ADXL202E
PIN CONFIGURATION
ABSOLUTE MAXIMUM RATINGS*
Acceleration (Any Axis, Unpowered for 0.5 ms) . . . . . . 1000 g
Acceleration (Any Axis, Powered for 0.5 ms) . . . . . . . . . . 500 g
+VS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +6.0 V
Output Short Circuit Duration, (Any Pin to Common)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Indefinite
Operating Temperature . . . . . . . . . . . . . . . . –55ЊC to +125ЊC
Storage Temperature . . . . . . . . . . . . . . . . . . –65ЊC to +150ЊC
V
DD
8
1
2
3
7
6
5
ST
X
Y
FILT
T2
FILT
OUT
X
COM
4
Y
OUT
*Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicate in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
BOTTOM VIEW
PIN FUNCTION DESCRIPTIONS
Drops onto hard surfaces can cause shocks of greater than 1000 g
and exceed the absolute maximum rating of the device. Care
should be exercised in handling to avoid damage.
Pin
No.
Mnemonic
Description
1
2
3
4
5
6
7
8
ST
T2
Self-Test
Connect RSET to Set T2 Period
Common
Y-Channel Duty Cycle Output
X-Channel Duty Cycle Output
Y-Channel Filter Pin
X-Channel Filter Pin
3 V to 5.25 V
Package Characteristics
Package
COM
YOUT
XOUT
YFILT
XFILT
VDD
Weight
ꢅJA
ꢅJC
Device
8-Lead LCC
120°C/W
tbd°C/W
<1.0 grams
ORDERING GUIDE
Specified Temperature
No.
of Axes
Package
Description
Package
Option
Model
Voltage
Range
ADXL202JE
ADXL202AE
2
2
3 V to 5 V
3 V to 5 V
0 to 70ЊC
–40ЊC to +85ЊC
8-Lead LCC
8-Lead LCC
E-8
E-8
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the ADXL202E features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
–3–
REV. A
ADXL202E–Typical Performance Characteristics*
VDD = 3 V
VDD = 5 V
16
14
12
10
8
18
16
14
12
10
8
6
6
4
4
2
2
0
0
1.28 1.32 1.36 1.41 1.45 1.49 1.53 1.58 1.62 1.66
VOLTS
2.05 2.14 2.23 2.31 2.40 2.48 2.57 2.65 2.74 2.82
VOLTS
TPC 1. X-Axis Zero g Bias Distribution at XFILT, VDD = 3 V
TPC 4. X-Axis Zero g Bias Distribution at XFILT, VDD = 5 V
25
20
15
10
5
16
14
12
10
8
6
4
2
0
0
2.05 2.14 2.23 2.31 2.40 2.48 2.57 2.65 2.74 2.82
1.25
1.31
1.36
1.42
1.48
1.53
1.59
1.65
VOLTS
VOLTS
TPC 2. Y-Axis Zero g Bias Distribution at YFILT, VDD = 3 V
TPC 5. Y-Axis Zero g Bias Distribution at YFILT, VDD = 5 V
25
20
15
10
5
25
20
15
10
5
0
0
0.148 0.155 0.162 0.169 0.176 0.182 0.189
0.26
0.28
0.29
0.30
0.32
0.33
0.34
0.142
V/g
V/g
TPC 6. X-Axis Sensitivity Distribution at XFILT, VDD = 5 V
TPC 3. X-Axis Sensitivity Distribution at XFILT, VDD = 3 V
*Data taken from 4500 parts over 3 lots minimum.
–4–
REV. A
ADXL202E
VDD = 3 V
VDD = 5 V
25
20
15
10
5
25
20
15
10
5
0
0
0.26
0.27
0.29
0.30
0.31
V/g
0.33
0.34
0.35
0.142 0.148 0.155 0.162 0.169 0.176 0.182 0.189
V/g
TPC 10. Y-Axis Sensitivity Distribution at YFILT, VDD = 5 V
TPC 7. Y-Axis Sensitivity Distribution at YFILT, VDD = 3 V
25
20
15
10
5
30
25
20
15
10
5
0
0
10.3
10.8
11.3
11.8
12.3
12.8
13.3
13.8
9.50
9.90
10.4
10.8
11.3
11.8
12.2
12.7
PERCENT DUTY CYCLE/g
PERCENT DUTY CYCLE/g
TPC 8. X-Axis Sensitivity at XOUT, VDD = 3 V
TPC 11. X-Axis Sensitivity at XOUT, VDD = 5 V
20
18
16
14
12
10
8
25
20
15
10
5
6
4
2
0
0
9.50
9.90
10.4
10.8
11.3
11.8
12.2
12.7
10.6
11.0
11.6
12.0
12.6
13.0
13.6
14.0
PERCENT DUTY CYCLE/g
PERCENT DUTY CYCLE/g
TPC 12. Y-Axis Sensitivity at YOUT, VDD = 5 V
TPC 9. Y-Axis Sensitivity at YOUT, VDD = 3 V
–5–
REV. A
ADXL202E
35
30
25
20
15
10
5
25
20
15
10
5
0
0
230 250 270 290 310 330 350 370 390 410
150
170
190
210
230
250
270
290
310
NOISE DENSITY – ꢁg Hz rms
NOISE DENSITY – ꢁg Hz rms
TPC 13. Noise Density Distribution, VDD = 3 V
TPC 16. Noise Density Distribution, VDD = 5 V
0.7
0.6
40
35
30
25
20
15
10
5
V
V
= 5 VDC
S
0.5
0.4
0.3
0.2
0.1
0
= 3.5 VDC
S
0
–40
–20
0
20
40
60
80
100
–3
–2
–1
0
1
2
3
TEMPERATURE – ꢄC
PERCENT – %
TPC 14. Typical Supply Current vs. Temperature
TPC 17. Cross-Axis Sensitivity Distribution
20
18
16
14
12
10
8
V
DD
3
2
1
0
C
= 0.01ꢁF
X
FILT
OUT
6
4
2
0
0
0.4
0.8
1.2
1.4
TIME – ms
DEGREES OF MISALIGNMENT
TPC 15. Rotational Die Alignment
TPC 18. Typical Turn-On Time
–6–
REV. A
ADXL202E
25
20
15
10
5
40
35
30
25
20
15
10
5
0
0
–0.73
–0.12
0.50
1.11
1.73
2.35
–2.08
–1.44
–0.80
–0.17
0.47
1.11
mg/ꢄC
mg/ꢄC
TPC 19. X-Axis Zero g Drift Due to Temperature
TPC 22. Y-Axis Zero g Drift Due to Temperature
Distribution, –40°C to +85°C
Distribution, –40°C to +85°C
20
18
16
14
12
10
8
40
30
20
10
0
6
4
2
0
–0.046 –0.038 –0.029 –0.021 –0.013 –0.004
PERCENT/
0.004
–0.046 –0.038 –0.029 –0.021 –0.013 –0.004
PERCENT/
0.004
ꢄ
C
ꢄ
C
TPC 20. X-Axis Sensitivity Drift at XFILT Due to
TPC 23. Y-Axis Sensitivity Drift at YFILT Due to
Temperature Distribution, –40°C to +85°C
Temperature Distribution, –40°C to +85°C
400
300
200
100
0
400
300
200
100
0
–100
–200
–300
–400
–100
–200
–300
–50
–25
0
25
50
75
100
–50
–25
0
25
50
75
100
TEMPERATURE – ꢄC
TEMPERATURE – ꢄC
TPC 21. Typical X-Axis Zero g vs. Output for 16 Parts
TPC 24. Typical Y-Axis Zero g vs. Output for 16 Parts
–7–
REV. A
ADXL202E
1.06
1.04
1.02
1.00
0.98
0.96
0.94
–45
–30
–15
0
15
30
45
60
75
90
TEMPERATURE – ꢄC
TPC 25. Normalized DCM Period (T2) vs. Temperature
DEFINITIONS
nominally 50% duty cycle. The acceleration signal can be deter-
T1
T2
Length of the “on” portion of the cycle.
Length of the total cycle.
mined by measuring the length of the T1 and T2 pulses with
a counter/timer or with a polling loop using a low cost micro-
controller.
Duty Cycle Ratio of the “on” time (T1) of the cycle to the total
cycle (T2). Defined as T1/T2 for the ADXL202E/
ADXL210.
Pulsewidth Time period of the “on” pulse. Defined as T1 for
the ADXL202E/ADXL210.
An analog output voltage can be obtained either by buffering the
signal from the XFILT and YFILT pin, or by passing the duty cycle
signal through an RC filter to reconstruct the dc value.
The ADXL202E will operate with supply voltages as low as 3.0 V
or as high as 5.25 V.
THEORY OF OPERATION
T2
The ADXL202E is a complete, dual-axis acceleration measurement
system on a single monolithic IC. It contains a polysilicon surface-
micromachined sensor and signal conditioning circuitry to imple-
ment an open loop acceleration measurement architecture. For
each axis, an output circuit converts the analog signal to a duty
cycle modulated (DCM) digital signal that can be decoded with
a counter/timer port on a microprocessor. The ADXL202E is
capable of measuring both positive and negative accelerations to
at least 2 g. The accelerometer can measure static acceleration
forces such as gravity, allowing it to be used as a tilt sensor.
T1
A(g) = (T1/T2 – 0.5)/12.5%
0g = 50% DUTY CYCLE
T2(s) = R
SET
(ꢂ)/125Mꢂ
Figure 1. Typical Output Duty Cycle
APPLICATIONS
POWER SUPPLY DECOUPLING
For most applications a single 0.1 µF capacitor, CDC, will
adequately decouple the accelerometer from signal and noise
on the power supply. However, in some cases, especially where
digital devices such as microcontrollers share the same power
supply, digital noise on the supply may cause interference on
the ADXL202E output. This may be observed as a slowly
undulating fluctuation of voltage at XFILT and YFILT. If additional
decoupling is needed, a 100 Ω (or smaller) resistor or ferrite
beads, may be inserted in the supply line of the ADXL202E.
The sensor is a surface micromachined polysilicon structure
built on top of the silicon wafer. Polysilicon springs suspend
the structure over the surface of the wafer and provide a resistance
against acceleration forces. Deflection of the structure is measured
using a differential capacitor that consists of independent fixed
plates and central plates attached to the moving mass. The fixed
plates are driven by 180° out of phase square waves. An accelera-
tion will deflect the beam and unbalance the differential capacitor,
resulting in an output square wave whose amplitude is propor-
tional to acceleration. Phase sensitive demodulation techniques are
then used to rectify the signal and determine the direction of
the acceleration.
FERRITE BEAD
100ꢂ
V
V
X
OUT
DD
DD
C
DC
ADXL202E
The output of the demodulator drives a duty cycle modulator
(DCM) stage through a 32 kΩ resistor. At this point a pin is
available on each channel to allow the user to set the signal band-
width of the device by adding a capacitor. This filtering improves
measurement resolution and helps prevent aliasing.
COM
ST
Y
X
Y
OUT
FILT
FILT
X
FILT
T2
After being low-pass filtered, the analog signal is converted to a
duty cycle modulated signal by the DCM stage. A single resistor
sets the period for a complete cycle (T2), which can be set between
0.5 ms and 10 ms (see Figure 12). A 0 g acceleration produces a
R
SET
Y
FILT
Figure 2.
–8–
REV. A
ADXL202E
DESIGN PROCEDURE FOR THE ADXL202E
Setting the Bandwidth Using CX and CY
The ADXL202E has provisions for bandlimiting the XFILT and
FILT pins. Capacitors must be added at these pins to implement
low-pass filtering for antialiasing and noise reduction. The equa-
tion for the 3 dB bandwidth is:
The design procedure for using the ADXL202E with a duty cycle
output involves selecting a duty cycle period and a filter capacitor.
A proper design will take into account the application requirements
for bandwidth, signal resolution and acquisition time, as discussed
in the following sections.
Y
1
F–3 dB
=
Decoupling Capacitor CDC
A 0.1 µF capacitor is recommended from VDD to COM for power
supply decoupling.
2 π (32 kΩ)× C(x, y)
(
)
5µF
F–3dB
=
ST
or, more simply,
C(X,Y )
The ST pin controls the self-test feature. When this pin is set to
VDD, an electrostatic force is exerted on the beam of the accelerom-
eter. The resulting movement of the beam allows the user to test if
the accelerometer is functional. The typical change in output will
be 10% at the duty cycle outputs (corresponding to 800 mg).
This pin may be left open circuit or connected to common in
normal use.
The tolerance of the internal resistor (RFILT), can vary typically as
much as 15% of its nominal value of 32 kΩ; so the bandwidth
will vary accordingly. A minimum capacitance of 1000 pF for
C(X, Y) is required in all cases.
Table I. Filter Capacitor Selection, CX and CY
Capacitor
Duty Cycle Decoding
The ADXL202E’s digital output is a duty cycle modulator.
Acceleration is proportional to the ratio T1/T2. The nominal
output of the ADXL202E is:
Bandwidth
Value
10 Hz
50 Hz
100 Hz
200 Hz
500 Hz
5 kHz
0.47 µF
0.10 µF
0.05 µF
0.027 µF
0.01 µF
0.001 µF
0 g = 50% Duty Cycle
Scale factor is 12.5% Duty Cycle Change per g
These nominal values are affected by the initial tolerance of the
device including zero g offset error and sensitivity error.
T2 does not have to be measured for every measurement cycle.
It need only be updated to account for changes due to tempera-
ture, (a relatively slow process). Since the T2 time period is shared
by both X and Y channels, it is necessary only to measure it on
one channel of the ADXL202E. Decoding algorithms for various
microcontrollers have been developed. Consult the appropriate
Application Note.
Setting the DCM Period with RSET
The period of the DCM output is set for both channels by a single
resistor from RSET to ground. The equation for the period is:
R
SET (Ω)
T2 =
125 MΩ
A 125 kΩ resistor will set the duty cycle repetition rate to approxi-
mately 1 kHz, or 1 ms. The device is designed to operate at duty
cycle periods between 0.5 ms and 10 ms.
3V TO 5.25V
C
X
V
X
FILT
SELF-TEST
X
DD
Table II. Resistor Values to Set T2
R
32kꢂ
X SENSOR
FILT
OUT
C
O
U
N
T
E
R
DEMOD
ANALOG
T2
RSET
TO
C
DC
OSCILLATOR
ꢁP
DUTY
CYCLE
(ADC)
ADXL202E
1 ms
2 ms
5 ms
10 ms
125 kΩ
250 kΩ
625 kΩ
1.25 MΩ
DEMOD
R
Y
FILT
OUT
Y SENSOR
COM
32kꢂ
Y
T2
R
FILT
C
Y
SET
Note that the RSET should always be included, even if only an
analog output is desired. Use an RSET value between 500 kΩ
and 2 MΩ when taking the output from XFILT or YFILT. The RSET
resistor should be place close to the T2 Pin to minimize parasitic
capacitance at this node.
T2
T1
A(g) = (T1/T2 – 0.5)/12.5%
0g = 50% DUTY CYCLE
Selecting the Right Accelerometer
T2 = R
/125Mꢂ
SET
For most tilt sensing applications the ADXL202E is the most
appropriate accelerometer. Its higher sensitivity (12.5%/g) allows
the user to use a lower speed counter for PWM decoding while
maintaining high resolution. The ADXL210 should be used in
applications where accelerations of greater than 2 g are expected.
Figure 3. Block Diagram
–9–
REV. A
ADXL202E
MICROCOMPUTER INTERFACES
With the single pole roll-off characteristic, the typical noise of
the ADXL202E is determined by the following equation:
The ADXL202E is specifically designed to work with low-cost
microcontrollers. Specific code sets, reference designs, and applica-
tion notes are available from the factory. This section will outline a
general design procedure and discuss the various trade-offs that
need to be considered.
Noise rms = 200 µg/ Hz × BW ×1.6
(
)
(
)
(
)
At 100 Hz the noise will be:
The designer should have some idea of the required performance
of the system in terms of:
Noise rms = 200 µg/ Hz
×
100 × 1.6 = 2.53 mg
(
)
(
)
(
)
Resolution: the smallest signal change that needs to be detected.
Bandwidth: the highest frequency that needs to be detected.
Acquisition Time: the time that will be available to acquire the signal
Often the peak value of the noise is desired. Peak-to-peak noise
can only be estimated by statistical methods. Table III is useful
for estimating the probabilities of exceeding various peak values,
given the rms value.
on each axis.
These requirements will help to determine the accelerometer band-
width, the speed of the microcontroller clock and the length of
the T2 period.
Table III. Estimation of Peak-to-Peak Noise
% of Time that Noise
When selecting a microcontroller it is helpful to have a counter
timer port available. The microcontroller should have provisions
for software calibration. While the ADXL202E is a highly accurate
accelerometer, it has a wide tolerance for initial offset. The easi-
est way to null this offset is with a calibration factor saved on the
microcontroller or by a user calibration for zero g. In the case
where the offset is calibrated during manufacture, there are several
options, including external EEPROM and microcontrollers with
“one-time programmable” features.
Nominal Peak-to-Peak Will Exceed Nominal
Value
Peak-to-Peak Value
2.0 × rms
4.0 × rms
6.0 × rms
8.0 × rms
32%
4.6%
0.27%
0.006%
The peak-to-peak noise value will give the best estimate of the
uncertainty in a single measurement.
Table IV gives typical noise output of the ADXL202E for various
DESIGN TRADE-OFFS FOR SELECTING FILTER
CHARACTERISTICS: THE NOISE/BW TRADE-OFF
The accelerometer bandwidth selected will determine the measure-
ment resolution (smallest detectable acceleration). Filtering can be
used to lower the noise floor and improve the resolution of the
accelerometer. Resolution is dependent on both the analog filter
bandwidth at XFILT and YFILT and on the speed of the micro-
controller counter.
C
X and CY values.
Table IV. Filter Capacitor Selection, CX and CY
Peak-to-Peak Noise
Estimate 95%
rms Noise Probability (rms ꢃ 4)
Bandwidth CX, CY
The analog output of the ADXL202E has a typical bandwidth
of 5 kHz, while the duty cycle modulators’ bandwidth is 500 Hz.
The user must filter the signal at this point to limit aliasing
errors. To minimize DCM errors the analog bandwidth should be
less than 1/10 the DCM frequency. Analog bandwidth may be
increased to up to 1/2 the DCM frequency in many applications.
This will result in greater dynamic error generated at the DCM.
10 Hz
50 Hz
100 Hz
200 Hz
500 Hz
0.47 µF
0.10 µF
0.05 µF
0.8 mg
1.8 mg
2.5 mg
3.2 mg
7.2 mg
10.1 mg
14.3 mg
22.6 mg
0.027 µF 3.6 mg
0.01 µF 5.7 mg
CHOOSING T2 AND COUNTER FREQUENCY: DESIGN
TRADE-OFFS
The noise level is one determinant of accelerometer resolution.
The second relates to the measurement resolution of the counter
when decoding the duty cycle output.
The analog bandwidth may be further decreased to reduce noise
and improve resolution. The ADXL202E noise has the character-
istics of white Gaussian noise that contributes equally at all
frequencies and is described in terms of µg per root Hz; i.e., the
noise is proportional to the square root of the bandwidth of the
accelerometer. It is recommended that the user limit bandwidth to
the lowest frequency needed by the application, to maximize the
resolution and dynamic range of the accelerometer.
The ADXL202E’s duty cycle converter has a resolution of
approximately 14 bits; better resolution than the accelerometer
itself. The actual resolution of the acceleration signal is, how-
ever, limited by the time resolution of the counting devices used
to decode the duty cycle. The faster the counter clock, the higher
the resolution of the duty cycle and the shorter the T2 period
can be for a given resolution. The following table shows some of
the trade-offs. It is important to note that this is the resolution
due to the microprocessors’ counter. It is probable that the
accelerometer’s noise floor may set the lower limit on the resolu-
tion, as discussed in the previous section.
–10–
REV. A
ADXL202E
Table V. Trade-Offs Between Microcontroller Counter Rate,
T2 Period, and Resolution of Duty Cycle Modulator
A DUAL AXIS TILT SENSOR: CONVERTING
ACCELERATION TO TILT
When the accelerometer is oriented so both its X and Y axes are
parallel to the earth’s surface it can be used as a two axis tilt sensor
with a roll and a pitch axis. Once the output signal from the
accelerometer has been converted to an acceleration that varies
between –1 g and +1 g, the output tilt in degrees is calculated as
follows:
Counter-
ADXL202E Clock
Counts
per T2 Counts Resolution
Cycle
RSET Sample
T2 (ms) (kꢂ) Rate
Rate
(MHz)
per g
(mg)
1.0
124 1000
124 1000
124 1000
625 200
625 200
625 200
1250 100
1250 100
1250 100
2.0
1.0
0.5
2.0
1.0
0.5
2.0
1.0
0.5
2000
1000
500
10000
5000
2500
20000
10000
5000
250
125
4.0
8.0
16.0
0.8
1.6
3.2
0.4
0.8
1.6
1.0
1.0
Pitch = ASIN (Ax/1 g)
Roll = ASIN (Ay/1 g)
62.5
1250
625
312.5
2500
1250
625
5.0
5.0
5.0
Be sure to account for overranges. It is possible for the acceler-
ometers to output a signal greater than 1 g due to vibration,
shock or other accelerations.
10.0
10.0
10.0
MEASURING 360ꢄ OF TILT
It is possible to measure a full 360° of orientation through gravity
by using two accelerometers oriented perpendicular to one another
(see Figure 5). When one sensor is reading a maximum change
in output per degree, the other is at its minimum.
STRATEGIES FOR USING THE DUTY CYCLE OUTPUT
WITH MICROCONTROLLERS
Application notes outlining various strategies for using the duty
cycle output with low cost microcontrollers are available from
the factory.
X
USING THE ADXL202E AS A DUAL-AXIS TILT SENSOR
One of the most popular applications of the ADXL202E is tilt
measurement. An accelerometer uses the force of gravity as an
input vector to determine orientation of an object in space.
360ꢄ OF TILT
1g
Y
An accelerometer is most sensitive to tilt when its sensitive axis
is perpendicular to the force of gravity, i.e., parallel to the earth’s
surface. At this orientation its sensitivity to changes in tilt is high-
est. When the accelerometer is oriented on axis to gravity, i.e.,
near its +1 g or –1 g reading, the change in output acceleration
per degree of tilt is negligible. When the accelerometer is perpen-
dicular to gravity, its output will change nearly 17.5 mg per degree
of tilt, but at 45° degrees it is changing only at 12.2 mg per
degree and resolution declines. The following table illustrates
the changes in the X and Y axes as the device is tilted 90°
through gravity.
Figure 5. Using a Two-Axis Accelerometer to Measure
360° of Tilt
USING THE ANALOG OUTPUT
The ADXL202E was specifically designed for use with its digital
outputs, but has provisions to provide analog outputs as well.
Duty Cycle Filtering
An analog output can be reconstructed by filtering the duty cycle
output. This technique requires only passive components. The
duty cycle period (T2) should be set to <1 ms. An RC filter with a
3 dB point at least a factor of >10 less than the duty cycle fre-
quency is connected to the duty cycle output. The filter resistor
should be no less than 100 kΩ to prevent loading of the output
stage. The analog output signal will be ratiometric to the supply
voltage. The advantage of this method is an output scale factor of
approximately double the analog output. Its disadvantage is that
X
+90
ꢄ
0
ꢄ
1g
Y
–90
ꢄ
BOTTOM VIEW
X Output
ꢆ per
Y Output (g)
the frequency response will be lower than when using the XFILT
YFILT output.
,
X Axis
ꢆ per
Orientation
to Horizon (
Degree of
Tilt (mg)
Degree of
Tilt (mg)
ꢄ)
X Output (g)
Y Output (g)
XFILT, YFILT Output
–90
–75
–60
–45
–30
–15
0
15
30
45
60
–1.000
–0.966
–0.866
–0.707
–0.500
–0.259
0.000
0.259
0.500
0.707
0.866
–0.2
4.4
8.6
0.000
0.259
0.500
0.707
0.866
0.966
1.000
0.966
0.866
0.707
0.500
0.259
0.000
17.5
16.9
15.2
12.4
8.9
The second method is to use the analog output present at the
XFILT and YFILT pin. Unfortunately, these pins have a 32 kΩ
output impedance and are not designed to drive a load directly.
An op amp follower may be required to buffer this pin. The
advantage of this method is that the full 5 kHz bandwidth of the
accelerometer is available to the user. A capacitor still must be
added at this point for filtering. The duty cycle converter should
be kept running by using RSET <10 MΩ. Note that the acceler-
ometer offset and sensitivity are ratiometric to the supply voltage.
The offset and sensitivity are nominally:
12.2
15.0
16.8
17.5
16.9
15.2
12.4
8.9
4.7
0.2
–4.4
–8.6
–12.2
–15.0
–16.8
–17.5
75
90
0.966
1.000
4.7
0.2
Figure 4. How the X and Y Axes Respond to Changes
in Tilt
0 g Offset = VDD/2
ADXL202E Sensitivity = (60 mV × VS)/g
–11–
REV. A
ADXL202E
USING THE ADXL202E IN VERY LOW POWER
APPLICATIONS
An application note outlining low power strategies for the
ADXL202E is available. Some key points are presented here.
It is possible to reduce the ADXL202E’s average current from
0.6 mA to less than 20 µA by using the following techniques:
CALIBRATING THE ADXL202E/ADXL210
The initial value of the offset and scale factor for the ADXL202E
will require calibration for applications such as tilt measurement.
The ADXL202E architecture has been designed so that these
calibrations take place in the software of the microcontroller used
to decode the duty cycle signal. Calibration factors can be stored in
EEPROM or determined at turn-on and saved in dynamic
memory.
1. Power Cycle the accelerometer.
2. Run the accelerometer at a Lower Voltage, (Down to 3 V).
For low g applications, the force of gravity is the most stable,
accurate and convenient acceleration reference available. A reading
of the 0 g point can be determined by orientating the device par-
allel to the earth’s surface and then reading the output.
Power Cycling with an External A/D
Depending on the value of the XFILT capacitor, the ADXL202E
is capable of turning on and giving a good reading in 1.6 ms. Most
microcontroller based A/Ds can acquire a reading in another 25 µs.
Thus it is possible to turn on the ADXL202E and take a reading
in <2 ms. If we assume that a 20 Hz sample rate is sufficient,
the total current required to take 20 samples is 2 ms × 20 samples/s
× 0.6 mA = 24 µA average current. Running the part at 3 V will
reduce the supply current from 0.6 mA to 0.4 mA, bringing the
average current down to 16 µA.
A more accurate calibration method is to make measurements at
+1 g and –1 g. The sensitivity can be determined by the two
measurements.
To calibrate, the accelerometer’s measurement axis is pointed
directly at the earth. The 1 g reading is saved and the sensor is
turned 180° to measure –1 g. Using the two readings, the sensi-
tivity is:
The A/D should read the analog output of the ADXL202E at
the XFILT and YFILT pins. A buffer amplifier is recommended, and
may be required in any case to amplify the analog output to give
enough resolution with an 8-bit to 10-bit converter.
Let A = Accelerometer output with axis oriented to +1 g
Let B = Accelerometer output with axis oriented to –1 g then:
Sensitivity = [A – B]/2 g
Power Cycling When Using the Digital Output
For example, if the +1 g reading (A) is 55% duty cycle and the
–1 g reading (B) is 32% duty cycle, then:
An alternative is to run the microcontroller at a higher clock rate
and put it into shutdown between readings, allowing the use of the
digital output. In this approach the ADXL202E should be set at
its fastest sample rate (T2 = 0.5 ms), with a 500 Hz filter at XFILT
and YFILT. The concept is to acquire a reading as quickly as pos-
sible and then shut down the ADXL202E and the microcontroller
until the next sample is needed.
Sensitivity = [55% – 32%]/2 g = 11.5%/g
These equations apply whether the output is analog or duty cycle.
Application notes outlining algorithms for calculating accelera-
tion from duty cycle and automated calibration routines are
available from the factory.
In either of the above approaches, the ADXL202E can be turned
on and off directly using a digital port pin on the microcontroller to
power the accelerometer without additional components.
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
8-Terminal Ceramic Leadless Chip Carrier
(E-8)
0.050 (1.27)
7
0.070 (1.78)
0.197 (5.00)
SQ
ꢇ
0.015 (0.38)
1
0.075
0.099
(2.50)
(1.91)
0.177
(4.50)
SQ
0.050 (1.27)
TOP VIEW
0.050 (1.27)
0.025
0.099
(2.50)
(0.64)
3
5
R0.008
(0.20)
ꢇ
0.015 (0.38)
R0.028 (0.70)
0.008
(0.20)
BOTTOM VIEW
CONTROLLING DIMENSIONS ARE IN MILLIMETERS
–12–
REV. A
相关型号：
ADXL203WCEZB-REEL
Precision 1.7g, -1.7g, 5g, -5g, 18g, -18g Single-/ Dual-Axis iMEMS Accelerometer
ADI
©2020 ICPDF网 联系我们和版权申明