CN-0313 [ADI]
EMC Compliant RS-485 Transceiver Protection Circuits; EMC兼容RS- 485收发器保护电路
| 型号： | CN-0313 |
| 厂家： | 
ADI |
| 描述： | EMC Compliant RS-485 Transceiver Protection Circuits |
| 文件： | 总5页 (文件大小：271K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Circuit Note
CN-0313
Devices Connected/Referenced
Circuits from the Lab™ reference circuits are engineered and
tested for quick and easy system integration to help solve today’s
analog, mixed-signal, and RF design challenges. For more
information and/or support, visit www.analog.com/CN0313.
15 kV ESD-Protected, 3.3 V,12 Mbps,
EIA RS-485 Transceiver
ADM3485E
EMC Compliant RS-485 Transceiver Protection Circuits
using the ADM3485E transceiver. Each solution was tested and
EVALUATION AND DESIGN SUPPORT
characterized to ensure that the dynamic interaction between
the transceiver and the protection circuit components functions
correctly together to protect against the electrostatic discharge
(ESD), electrical fast transients (EFT), and surge immunity
specified in IEC 61000-4-2, IEC 61000-4-4, and IEC 61000-4-5,
respectively. The circuits offer proven protection for RS-485
interfaces using the ADM3485E to the ESD, EFT, and surge
levels often encountered in harsh environments.
Circuit Evaluation Boards
CN-0313 Circuit Evaluation Board (EVAL-CN0313-SDPZ)
Design and Integration Files
Schematics, Layout Files, Bill of Materials
CIRCUIT FUNCTION AND BENEFITS
The circuits shown in Figure 1 demonstrate proven and tested
electromagnetic compatibility (EMC) compliant solutions for
three protection levels for popular RS-485 communication ports
V
V
CC
CC
ADM3485E
ADM3485E
TBU
TBU-CA065-200-WH
B
A
B
A
RO
RE
RO
RE
120Ω
120Ω
DI
DI
TISP
TISP4240M3BJR-S
DE
DE
TVS
CDS0T23-SM712
TVS
CDS0T23-SM712
PROTECTION SCHEME 1. TVS
PROTECTION SCHEME 2. TVS/TBU/TISP
V
CC
ADM3485E
TBU
TBU-CA065-200-WH
B
A
RO
RE
120Ω
GDT
2038-15-SM-RPLF
DI
DE
TVS
CDS0T23-SM712
PROTECTION SCHEME 3. TVS/TBU/GDT
Figure 1. Three EMC Compliant ADM3485E Protection Circuits (Simplified Schematic, All Connections Not Shown)
Rev. 0
Circuits from the Lab™ circuits from Analog Devices have been designed and built by Analog Devices
engineers. Standard engineering practices have been employed in the design and construction of
each circuit, andtheir function andperformance have been tested and verifiedin a lab environment at
room temperature. However, you are solely responsible for testing the circuit and determining its
suitability and applicability for your use and application. Accordingly, in noevent shall Analog Devices
be liable for direct, indirect, special, incidental, consequential or punitive damages due to any cause
whatsoever connectedtothe use ofanyCircuitsfromtheLabcircuits. (Continuedon last page)
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2013 Analog Devices, Inc. All rights reserved.
CN-0313
Circuit Note
Table 1. Protection Levels Offered by Each of the Three
Protection Circuits in Figure 1
CIRCUIT DESCRIPTION
The RS-485 bus standard is one of the most widely used physical
layer bus designs in industrial and instrumentation applications.
RS-485 offers differential data transmission between multiple
systems often over very long distances. Applications for RS-485
include process control networks; industrial automation; remote
terminals; building automation, such as heating, ventilation, air
conditioning (HVAC) and security systems; motor control; and
motion control.
Protection Scheme ESD
EFT (kV) Surge (kV)
1. TVS
8 kV contact,
15 kV air discharge
8 kV contact,
15 kV air discharge
2
2
2
1
4
6
2. TVS/TBU/TISP
3. TVS/TBU/GDT
8 kV contact,
15 kV air discharge
Figure 2 shows a photo of the EVAL-CN0313-SDPZ board. There
are three ADM3485E devices on the board, one for each
protection scheme. Each protection scheme provides ESD and
EFT protection as described and increasing levels of surge
protection.
In these real systems, lightning strikes, power source fluctuations,
inductive switching, and electrostatic discharge can cause
damage to communications ports by generating large transient
voltages. Designers must ensure that equipment does not just
work in ideal conditions, but it must also work in real-world
conditions. To ensure that these designs can work in electrically
harsh environments, EMC regulations must be met.
A complete design support package for the EVAL-CN0313-
SDPZ board including schematics, layout files, and bill of
materials can be found at www.analog.com/CN0313-
DesignSupport.
Many EMC problems are not simple or obvious and must be
considered at the start of the product development cycle. Proper
solutions and protection circuits must be part of the total design
effort and not left to the last minute. The protection circuits
must incorporate the input and output structure of the specific
transceiver manufacturer as part of the design.
The IEC 61000 specifications define the set of EMC immunity
requirements. Within this set of specifications, designers must
be concerned with the following three types of high voltage
transients for data communication lines:
•
•
•
IEC 61000-4-2 electrostatic discharge (ESD)
IEC 61000-4-4 electrical fast transients (EFT)
IEC 61000-4-5 surge immunity
ESD and EFT have similar rise times, pulse widths, and energy
levels. The surge transient has longer rise times and pulse widths; as
a result, the surge transient energy can be three to four orders of
magnitude larger than the energy in an ESD or EFT transient.
Due to the similarities between ESD and EFT transients, the
design of the circuit protection can be similar. However, due to
the high energy associated with surge transients, they must be
dealt with differently.
Each solution protects data ports to ESD voltages of 8 kV
contact and 15 kV air discharge, and EFT voltages of 2 kV. The
different solutions provide an increased level of surge
protection up to 6 kV. Protection levels for the circuits are
summarized in Table 1.
Figure 2. EVAL-CN0313-SDPZ Board
Rev. 0 | Page 2 of 5
Circuit Note
CN-0313
The ADM3485E is a 3.3 V, low power data transceiver suitable
for half-duplex communication on multipoint transmission lines.
It has a data rate up to 12 Mbps with a common-mode range on
the bus pins (A and B) of −7 V to +12 V. Data transmits on the
DI pin, and it is received on the RO pin. Both the driver and
receiver outputs can be enabled or disabled, that is, put into a
high impedance state, by changing the logic levels on the DE
In the first protection circuit, shown in Figure 1 as TVS, it uses one
component, the Bourns CDSOT23-SM712. This is the transient
voltage suppressor (TVS) array shown on the EVAL-CN0313-
SDPZ. It consists of two bidirectional TVS diodes optimized to
protect RS-485 systems with minimal overstress while allowing
the full range of the RS-485 signal and common-mode excursions.
The TVS has high impedance to ground in normal operating
conditions. When an overvoltage occurs, the TVS enters into
avalanche breakdown mode and clamps the pin voltage to a safe
predetermined level. It then diverts the transient current away
from the ADM3485E to ground.
RE
and
pins, respectively.
Power and ground are connected via a screw-wire connector (VCC
and GND). This connector supplies all three ADM3485E devices.
RE
Logic inputs DE and
are set using LK1 to LK6. For each
This protection scheme offers up to 8 kV contact and15 kV air
discharge ESD, 2 kV EFT, and 1 kV surge protection.
ADM3485E, LK2, LK4, and LK6 relate to DE and LK1, LK3, and
RE
LK5 relate to . For each link, Position A connects the logic pin
As described in the CDSOT23-SM712 data sheet, the part is
designed specifically for RS-485 devices. The next two protection
schemes add to the CDSOT23-SM712 to provide higher levels
of circuit protection against surge.
to VCC, Position B connects the logic pin to GND, and Position C
connects the logic pin to the four terminal, side screw-wire
connector. The input DI and output RO pins are connected
directly to the four terminal screw connector.
In the second scheme, shown in Figure 1 as TVS/TBU/TISP,
the CDSOT23-SM712 TVS provides secondary protection, and
Bourns TISP4240M3BJR-S provides the primary protection. The
TISP4240M3BJR-S is a totally integrated surge protector (TISP).
The TISP is a solid-state thyristor. When its predetermined voltage
is exceeded, the TISP provides a low impedance path to ground,
diverting a majority of the transient energy away from the
ADM3485E.
The EVAL-CN0313-SDPZ is also compatible with the Analog
Devices, Inc., ezLINX™ board (EZLINX-IIIDE-EBZ) and the
system development platform (EVAL-SDP-CB1Z). Connector J8
links the UART and GPIO interfaces on the SDP or the ezLINX
board to the logic I/O of the ADM3485E devices. The I/O
connections and jumper configurations are shown in Table 2.
Table 2. ezLINX and SDP I/O Connections and Jumper
Configurations
Bourns TBU-CA065-200-WH transient blocking unit (TBU) is
a nonlinear overcurrent protection device between the primary
and secondary protection devices that ensures coordination
occurs. The TBU is an overcurrent blocking device that becomes
an open circuit at a predefined current. In blocking mode, TBU
has very high impedance to block transient energy. This protection
scheme offers up to 8 kV contact and15 kV air discharge ESD,
2 kV EFT, and 4 kV surge protection.
ADM3485E
I/O Pin
SDP/ezLINX Connector Selection
TVS
RO
RE
UART_RX
GPIO_0
LK7 (A)
LK1 (C)
LK2 (C)
LK8 (A)
LK7 (B)
LK3 (C)
LK4 (C)
LK8 (B)
LK7 (C)
LK5 (C)
LK6 (C)
LK8 (C)
DE
DI
GPIO_3
UART_TX
UART_RX
GPIO_1
TVS/TBU/TISP RO
RE
DE
DI
GPIO_4
The third protection scheme, shown in Figure 1 as TVS/TBU/
GDT, operates in a similar fashion to Protection Scheme 2. In
this scheme, a gas discharge tube (GDT) is used instead of the
TISP. The GDT protects to higher overvoltages and overcurrents
than the TISP described in the previous protection scheme.
A GDT is a gas discharge plasma device that provides a low
impedance path to ground to protect against over voltage
transients. The selected GDT is the Bourns 2038-15-SM-RPLF.
UART_TX
UART_RX
GPIO_2
TVS/TBU/GDT RO
RE
DE
DI
GPIO_5
UART_TX
The ADM3485E transmitter and receiver share the same differential
bus pins (A and B). The protection circuitry is used to protect
these bus pins.
This third protection scheme offers up to 8 kV contact and
15 kV air discharge ESD, 2 kV EFT, and 6 kV surge protection.
The ADM3485E has a 120 Ω termination attached to the bus pins.
Rev. 0 | Page 3 of 5
CN-0313
Circuit Note
For IEC 61000-4-4 EFT testing, a capacitive coupling clamp is
used to couple the EFT bursts onto the cable connected to the
bus lines. The coupling capacitance of the clamp depends on the
cable diameter, material of the cables, and cable shielding.
CIRCUIT EVALUATION AND TEST
Apply 3.3 V to VCC to power the EVAL-CN0313-SDPZ board.
The voltage can be checked on the VCC test points near each
ADM3485E. The transmit and receive paths can be tested by
connecting one of the ADM3485E circuits as shown in Figure 3.
A signal or pattern generator can be connected to DI. The outputs
of the driver can be monitored on the A and B test points, and the
output of the receiver can be monitored on the RO test point.
Jumper configurations are also shown in Figure 3. This test
setup can apply to any of the three circuits.
IEC 61000-4-5 surge testing implies the use of a coupling/
decoupling network (CDN) to couple the surge transient into
the bus pins. According to the specification, this must be done
using two 80 Ω resistors for a two port test. Figure 4 shows the
test setup for surge testing. Connect the CDN to the A and B
terminals, and the common of the surge generator to the
ground connection of the four terminal screw connector.
V
CC
SIGNAL
GENERATOR
ADM3485E
CDN
B
A
RO
RE
80Ω
PROTECTION
COMPONENTS
3.3V
POWER
SUPPLY
OSCILLOSCOPE
120Ω
80Ω
DI
DE
A
B
C
RO
RE
DE
DI
B
A
Figure 4. IEC 61000-4-5 Surge CDN to ADM3485E Setup
A
B
C
All protection circuits described were characterized in the lab
with the ADM3485E and verified by an external independent
EMC compliance test house.
Figure 3. Transmit and Receive Test Setup
For further information on the ezLINX iCoupler® isolated interface
development environment, go to
http://wiki.analog.com/resources/eval/ezlinx.
According to IEC 61000-4-2, ESD testing implies using two
coupling methods, contact discharge and air gap discharge.
Contact discharge implies the discharge gun is placed in direct
connection with the port being tested. With air discharge, the
charged electrode of the discharge gun is moved toward the
port under test until a discharge occurs developing an arc across
the air gap. Apply discharges to the screw terminal connector of
each bus line.
Information on other important EMC issues can be found at
http://www.analog.com/rs485emc.
Rev. 0 | Page 4 of 5
Circuit Note
CN-0313
Data Sheets and Evaluation Boards
ADM3485E Data Sheet
LEARN MORE
CN-0313 Design Support Package:
http://www.analog.com/CN0313-DesignSupport
System Development Platform (EVAL-SDP-CB1Z)
ezLINX™ iCoupler® Isolated Interface Development
Environment, ezLINX Board Quick Start Guide
ezLINX™ iCoupler® Isolated Interface Development
Environment (EZLINX-IIIDE-EBZ)
Certified EMC Compliant RS-485 Interface Design Tool
UG-400 User Guide, ezLINX™ iCoupler® Isolated Interface
Development Environment, Analog Devices.
Marais, Hein. Application Note AN-960. RS-485/RS-422 Circuit
Implementation Guide. Analog Devices, Inc.
CDSOT23-SM712—Surface Mount TVS Diode Data Sheet,
Bourns
Electromagnetic Compatibility (EMC) Part 4-2: Testing and
Measurement Techniques–Electrostatic Discharge Immunity
Test (IEC 61000-4-2)
TISP4xxxM3BJ Overvoltage Protector Series (TISP4240M3BJR-S)
Data Sheet, Bourns
Electromagnetic Compatibility (EMC) Part 4-4: Testing and
Measurement Techniques–Electrical Fast Transient/Burst
Immunity Test (IEC 61000-4-4)
TBU-CA Series—TBU® High Speed Protectors (TBU-CA065-
200-WH) Data Sheet, Bourns
2038 Series Miniature Symmetrical Three Electrode Surface
Mount Gas Discharge Tube (2038-15-SM-RPLF) Data Sheet,
Bourns
Electromagnetic Compatibility (EMC) Part 4-5: Testing and
Measurement Techniques–Surge Immunity Test (IEC 61000-4-5)
REVISION HISTORY
2/13—Revision 0: Initial Version
(Continued from first page) Circuits from the Lab circuits are intended only for use with Analog Devices products and are the intellectual property of Analog Devices or its licensors. While you
may use the Circuits from the Lab circuits in the design of your product, no other license is granted by implication or otherwise under any patents or other intellectual property by
application or use of the Circuits from the Lab circuits. Information furnished by Analog Devices is believed to be accurate and reliable. However, Circuits from the Lab circuits are supplied
"as is" and without warranties of any kind, express, implied, or statutory including, but not limited to, any implied warranty of merchantability, noninfringement or fitness for a particular
purpose and no responsibility is assumed by Analog Devices for their use, nor for any infringements of patents or other rights of third parties that may result from their use. Analog Devices
reserves the right to change any Circuits from the Lab circuits at any time without notice but is under no obligation to do so.
©2013 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
CN11250-0-2/13(0)
Rev. 0 | Page 5 of 5
相关型号：
©2020 ICPDF网 联系我们和版权申明