EVAL-AD1990EB [ADI]
Audio Switching Amplifier; 音频开关放大器
| 型号： | EVAL-AD1990EB |
| 厂家： | 
ADI |
| 描述： | Audio Switching Amplifier |
| 文件： | 总16页 (文件大小：405K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Audio Switching Amplifier
AD1990
FEATURES
GENERAL DESCRIPTION
Integrated stereo modulator and power stage
<0.002% THD + N
101 dB dynamic range (A-weighted)
2 × 5 W output power (4 Ω, <0.01% THD + N)
RDS-ON < 0.3 Ω (per transistor)
PSRR > 65 dB
On-off-mute pop noise suppression
EMI optimized modulator
Short-circuit protection
The AD1990 is a 2-channel, bridge tied load (BTL), switching
audio power amplifier with integrated Σ-Δ modulator. The
modulator accepts a single-ended, analog input signal and
converts it to a switching waveform to drive speakers directly. A
digital, microprocessor-compatible interface provides control of
reset, mute, and PGA gain, as well as feedback signals for thermal
and overcurrent error conditions. The output stage can operate
over a power supply voltages range of 8 V to 12 V. The analog
modulator and digital logic operate from a 5 V supply.
Overtemperature protection
Low cost DMOS process
APPLICATIONS
Advanced televisions
Compact multimedia systems
Minicomponents
FUNCTIONAL BLOCK DIAGRAM
FEEDBACK
NETWORK
PGA1
PGA0
AV
DV
DD
PV
DD
DD
AD1990
A1
A2
OUTL+
AINL
Σ-Δ
MODULATOR
PGA
B1
B2
LEVEL
SHIFTER
AND
DEAD TIME
CONTROL
OUTL–
OUTR+
H-BRIDGE
AINR
Σ-Δ
MODULATOR
PGA
C1
C2
CLKI
MODE CONTROL
LOGIC AND
OSCILLATOR
POP/CLICK
CLKO
SUPPRESSION
D1
D2
REF_FILT
OUTR–
VOLTAGE
REFERENCE
AGND
PGND
FEEDBACK
NETWORK
Figure 1.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2006 Analog Devices, Inc. All rights reserved.
AD1990
TABLE OF CONTENTS
Features .............................................................................................. 1
Overview ..................................................................................... 11
Σ-Δ Modulator............................................................................ 11
Applications....................................................................................... 1
General Description......................................................................... 1
Functional Block Diagram .............................................................. 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Absolute Maximum Ratings............................................................ 5
ESD Caution.................................................................................. 5
Pin Configuration and Function Descriptions............................. 6
Typical Performance Characteristics ............................................. 8
Theory of Operation ...................................................................... 11
MUTE
RESET
..................................................................... 11
and
Gain Structure............................................................................. 11
Power Stage ................................................................................. 13
Clocking....................................................................................... 13
Protection Circuits and Error Reporting ................................ 14
Application Circuits ....................................................................... 15
Outline Dimensions....................................................................... 16
Ordering Guide .......................................................................... 16
REVISION HISTORY
4/06—Revision 0: Initial Version
Rev. 0 | Page 2 of 16
AD1990
SPECIFICATIONS
Test conditions, unless otherwise specified.
Table 1.
Parameter
Ratings
SUPPLY VOLTAGES
AVDD
5 V
DVDD
5 V
PVDD
12 V
AMBIENT TEMPERATURE
LOAD IMPEDANCE
CLOCK FREQUENCY
PGA GAIN
25°C
6 Ω
12.288 MHz
0 dB
MEASUREMENT BANDWIDTH
20 Hz to 20 kHz
Table 2.
Parameter
Min
Typ
Max
Unit
Test Conditions/Comments
RDS-ON
Per High-Side Transistor
Per Low-Side Transistor
MAXIMUM CURRENT THROUGH OUTx
THERMAL WARNING ACTIVE
THERMAL SHUTDOWN ACTIVE
RESTORE TEMPERATURE AFTER THERMAL SHUTDOWN
260
210
5
355
265
mΩ
mΩ
A
T = 25°C
T = 25°C
Peak
135
150
120
°C
Die temperature
Die temperature
Die temperature
°C
°C
Table 3. Performance Specifications
Parameter
Typ
Unit Test Conditions/Comments
TOTAL HARMONIC DISTORTION AND NOISE (THD + N)
0.003
0.006
0.01
0.02
102
%
%
%
%
PGA = 0 dB, PO = 1 W, 1 kHz
PGA = 6 dB, PO = 1 W, 1 kHz
PGA = 12 dB, PO = 1 W, 1 kHz
PGA = 18 dB, PO = 1 W, 1 kHz
SIGNAL-TO-NOISE RATIO (SNR)
dB
dB
dB
1 kHz, A-weighted, 0 dB referred to 1% THD + N output
1 kHz, A-weighted, −60 dB referred to 1% THD + N output
PGA = 0 dB, PO = 5 W, 1 kHz
DYNAMIC RANGE (DNR)
102
CROSSTALK (LEFT-TO-RIGHT OR RIGHT-TO-LEFT)
−100
Table 4. DC Specifications
Parameter
Typ
20
Unit
kΩ
Test Conditions/Comments
AINL, AINR input pins
INPUT IMPEDANCE
OUTPUT DC OFFSET
±±
mV
Independent of PGA setting
Rev. 0 | Page 3 of 16
AD1990
Table 5. Power Supplies
Parameter
Min
±.5
±.5
6.5
Typ
5.0
Max
5.5
5.5
15
Unit
Test Conditions/Comments
ANALOG SUPPLY, AVDD
V
V
V
DIGITAL SUPPLY, DVDD
5.0
POWER TRANSISTOR SUPPLY, PVDD
8 to 12
RESET/POWER-DOWN CURRENT
RESET held low
AVDD
DVDD
PVDD
0.6
7.5
19
1
11
±0
μA
μA
μA
5 V
5 V
12 V
QUIESCENT CURRENT
Inputs grounded, nonoverlap = minimum
AVDD
DVDD
PVDD
20
5.5
30
mA
mA
mA
5 V
5 V
12 V
OPERATING CURRENT
VIN = 1 V rms, RL = 6 Ω, PO = 1 W
AVDD
DVDD
PVDD
20
5.5
218
27
7
260
mA
mA
mA
5 V
5 V
12 V
Table 6. Digital I/O
Parameter
Min
Typ
Max
Unit
V
Test Conditions/Comments
INPUT LOGIC HIGH
2.0
INPUT LOGIC LOW
0.8
V
OUTPUT LOGIC HIGH
OUTPUT LOGIC LOW
LEAKAGE CURRENT ON DIGITAL OUTPUTS
2.±
V
@ ± mA
@ ± mA
0.±
10
V
μA
Table 7. Digital Timing
Parameter
Typ
Unit
μs
Test Conditions/Comments
tMD
tUD
10
Delay after MUTE is asserted until output stops switching
Delay after MUTE is deasserted until output starts switching
3±
μs
tMD
tUD
MUTE
OUTx
Figure 2. Mute and Unmute Delay Timing
Rev. 0 | Page ± of 16
AD1990
ABSOLUTE MAXIMUM RATINGS
Table 8.
Parameter
AVDD, DVDD to AGND, DGND
PVDDx to PGNDx1
AGND to DGND to PGNDx
AVDD, to DVDD
Operating Temperature Range
Storage Temperature Range
Maximum Junction Temperature
Thermal Resistance
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rating
−0.3 V to +6.5 V
−0.3 V to +22.5 V
−0.3 V to +0.3 V
−0.5 V to +0.5 V
–±0°C to +85°C
–65°C to +150°C
150°C
θJA
19.2°C/W
0.9°C/W
9.7°C/W
θJC (at the Exposed Pad Surface)
θJB (on JEDEC Standard PCB)
1 Including any induced voltage due to inductive load.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as ±000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 5 of 16
AD1990
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
PIN 1
INDICATOR
PGND1
PGND1
PGND1
OUTL+
OUTL+
OUTL+
PVDD1
PVDD1
PVDD1
PVDD1 10
OUTL– 11
OUTL– 12
OUTL– 13
PGND1 14
PGND1 15
PGND1 16
1
2
3
4
5
6
7
8
9
48 PGND2
47 PGND2
46 PGND2
45 OUTR+
44 OUTR+
43 OUTR+
42 PVDD2
41 PVDD2
40 PVDD2
39 PVDD2
38 OUTR–
37 OUTR–
36 OUTR–
35 PGND2
34 PGND2
33 PGND2
AD1990
TOP VIEW
(Not to Scale)
NC = NO CONNECT
Figure 3. Pin Configuration
Table 9. Pin Function Descriptions
Pin No.
1, 2, 3, 6±
±, 5, 6
7, 8, 9, 10
11, 12, 13
1±, 15, 16
17
Mnemonic
PGND1
OUTL+
PVDD1
OUTL−
PGND1
ERR2
In/Out
Description
Negative Power Supply. Used for the A2 and B2 high power transistors.
Output of Transistor Pair A1 and A2.
Positive Power Supply. Used for the A1 and B1 high power transistors.
Output of Transistor Pair B1 and B2.
Negative Power Supply. Used for the A2 and B2 high power transistors.
Active Low Thermal Shutdown Error Output.
Active Low Thermal Warning Error Output.
Active Low Overcurrent Error Output.
O
O
O
O
O
I/O
I
18
ERR1
19
ERR0
20
21
22
23, 26
2±, 25
27
28
29
DCTRL2
DCTRL1
DCTRL0
DGND
DVDD
CLKI
Nonoverlap Time Setting MSB.
Nonoverlap Time Setting.
Nonoverlap Time Setting LSB.
Negative Power Supply for Low Power Digital Circuitry.
Positive Power Supply for Low Power Digital Circuitry.
Clock Input for 256 × fS Audio Modulator Clock.
Inverted Version of CLKI for Use with an External XTAL Oscillator.
Active Low Mute Input.
I
I
O
I
CLKO
MUTE
30
RESET
PGA1
I
Active Low Reset Input.
31
I
PGA Gain Control MSB.
32
PGA0
I
PGA Gain Control LSB.
33, 3±, 35
36, 37, 38
39, ±0, ±1, ±2
±3, ±±, ±5
±6, ±7, ±8, ±9
50
PGND2
OUTR−
PVDD2
OUTR+
PGND2
NFR+
Negative Power Supply for High Power Transistors C2 and D2.
Output of Transistor Pair D1 and D2.
Positive Power Supply for High Power Transistors C1 and D1.
Output of Transistor Pair C1 and C2.
Negative Power Supply for High Power Transistors C2 and D2.
Right Channel Negative Feedback—Noninverting Input.
Right Channel Negative Feedback—Inverting Input.
O
O
I
I
51
NFR−
Rev. 0 | Page 6 of 16
AD1990
Pin No.
Mnemonic
NC
AINR
REF_FILT
AGND
AVDD
MOD_FILT
AINL
In/Out
Description
52, 5±, 59, 61
No Connection—Should Be Left Floating.
Analog Input for Right Channel.
Filter Pin for Band Gap Reference—Should Be Bypassed to AGND.
Negative Power Supply for Low Power Analog Circuitry.
Positive Power Supply for Low Power Analog Circuitry.
Modulator Filter Pin—Used to Set Time Constant of Modulator Order Reduction Circuit.
Analog Input for Left Channel.
Left Channel Negative Feedback—Inverting Input.
53
55
56
57
58
60
62
63
6±
I
O
O
O
I
NFL−
NFL+
PGND1
I
Left Channel Negative Feedback—Noninverting Input.
Negative Power Supply. Used for the A2 and B2 high power transistors.
Rev. 0 | Page 7 of 16
AD1990
TYPICAL PERFORMANCE CHARACTERISTICS
0
0
–20
–20
–40
–40
–60
–60
–80
–80
–100
–120
–140
–160
–100
–120
–140
–160
0
2
4
6
8
10
12
14
16
18
20
0
2
4
6
8
10
12
14
16
18
20
FREQUENCY (kHz)
FREQUENCY (kHz)
Figure 4. 1 W Output Power into 4 Ω Load
Figure 7. −60 dBFS Output Power into 4 Ω Load
0
–20
0
–20
–40
–40
–60
–60
–80
–80
–100
–120
–140
–160
–100
–120
–140
–160
0
2
4
6
8
10
12
14
16
18
20
0
2
4
6
8
10
12
14
16
18
20
FREQUENCY (kHz)
FREQUENCY (kHz)
Figure 5. 1 W Output Power into 6 Ω Load
Figure 8. −60 dBFS Output Power into 6 Ω Load
0
–20
0
–20
–40
–40
–60
–60
–80
–80
–100
–120
–140
–160
–100
–120
–140
–160
0
2
4
6
8
10
12
14
16
18
20
0
2
4
6
8
10
12
14
16
18
20
FREQUENCY (kHz)
FREQUENCY (kHz)
Figure 6. 1 W Output Power into 8 Ω Load
Figure 9. −60 dBFS Output Power into 8 Ω Load
Rev. 0 | Page 8 of 16
AD1990
20
0
1
0.1
–40
–50
–60
–70
–80
–90
–100
–20
–40
–60
–80
–100
–120
–140
0.01
0.001
0.0001
–110
–120
100
1k
10k
100
1k
10k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 10. IMD for 19 kHz/20 kHz Twin-Tone Stimulus with
500 mW Power in Each Tone
Figure 13. THD vs. Frequency, 1 W Output Power into 4 Ω Load, PVDD = 12 V
40
1
–40
–50
–60
–70
–80
–90
–100
PGA GAIN = 18dB
PGA GAIN = 12dB
35
30
25
20
15
10
5
0.1
PGA GAIN = 6dB
PGA GAIN = 0dB
0.01
0.001
0.0001
–110
–120
0
100
1k
10k
100
1k
10k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 11. Amplifier Gain vs. Frequency, 6 Ω Load, PVDD = 12 V
Figure 14. THD vs. Frequency, 1 W Output Power into 6 Ω Load, PVDD = 12 V
0
–20
–40
–60
1
–40
–50
–60
–70
–80
–90
–100
0.1
0.01
L CHANNEL IDLE,
–80
–100
–120
R CHANNEL DRIVEN
0.001
0.0001
–110
–120
L CHANNEL DRIVEN,
R CHANNEL IDLE
100
1k
FREQUENCY (Hz)
10k
100
1k
10k
FREQUENCY (Hz)
Figure 12. Channel Separation vs. Frequency, Driven Channel Has
1 W Output Power into 6 Ω Load
Figure 15. THD vs. Frequency, 1 W Output Power into 8 Ω Load, PVDD = 12 V
Rev. 0 | Page 9 of 16
AD1990
100
0
10
9
8
7
6
5
4
3
2
1
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
10
THD = 10%
1
0.1
0.01
THD = 1%
THD + N
THD
0.001
0.1
1
10
8.0
8.5
9.0
9.5
10.0
10.5
11.0
11.5
12.0
OUTPUT POWER (W)
PVDD VOLTAGE (V)
Figure 19. Maximum Output Power vs. PVDD, 4 Ω Load
Figure 16. THD and THD + N vs. Output Power, 1 kHz Sine, 4 Ω Load, PVDD = 12 V
10
9
8
7
6
5
4
3
2
1
0
100
10
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
1
THD = 10%
THD = 1%
0.1
THD + N
0.01
0.001
THD
8.0
8.5
9.0
9.5
10.0
10.5
11.0
11.5
12.0
0.1
1
10
PVDD VOLTAGE (V)
OUTPUT POWER (W)
Figure 20. Maximum Output Power vs. PVDD, 6 Ω Load
Figure 17. THD and THD + N vs. Output Power, 1 kHz Sine, 6 Ω Load, PVDD = 12 V
10
9
8
7
6
5
4
3
2
1
0
100
10
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
1
0.1
THD = 10%
THD + N
0.01
0.001
THD = 1%
THD
8.0
8.5
9.0
9.5
10.0
10.5
11.0
11.5
12.0
0.1
1
10
PVDD VOLTAGE (V)
OUTPUT POWER (W)
Figure 21. Maximum Output Power vs. PVDD, 8 Ω Load
Figure 18. THD and THD + N vs. Output Power, 1 kHz Sine, 8 Ω Load, PVDD = 12 V
Rev. 0 | Page 10 of 16
AD1990
THEORY OF OPERATION
OVERVIEW
MUTE AND RESET
The AD1990 is a 2-channel, high performance, switching, audio
power amplifier. Each of the two Σ-Δ modulators converts a
single-ended analog input into a 2-level pulse stream that
controls the differential, full H-bridge, power output stage. The
combination of an Σ-Δ modulator and a switching power stage
provides an inherently linear and efficient means of amplifying
the entire range of audio frequencies. The AD1990 also offers
warning and protection circuits for overcurrent and over-
temperature conditions, as well as silent turn-on and turn-off
transitions.
RESET
When power is applied and the
pin remains asserted,
the AD1990 is in its lowest power consumption mode. The
analog modulator is not running, and the power stage is tri-
RESET
stated. On deasserting the
pin, the modulator begins a
start-up sequence that includes initialization of the modulator,
the protection circuits, and other functions.
Once the start-up sequence is complete, the amplifier is in a
state in which the modulator is running, but the output stage is
is deasserted, the output is started
using a soft-start sequence that avoids any audible pop or click
noise in the output signal.
MUTE
not driven. When
Σ-Δ MODULATOR
The AD1990 is a switching type, also known as a Class-D, audio
power amplifier. This class of amplifiers maximizes efficiency
by only using its power output devices in full-on or full-off
states. While most Class-D amplifiers use some variation of
pulse-width modulation (PWM), the AD1990 uses Σ-Δ
modulation to determine the switching pattern of the output
devices. This provides a number of important benefits. Σ-Δ
modulators do not produce a sharp peak with many harmonics
in the AM frequency band as pulse-width modulators (PWM)
often do. In addition, the 1-bit quantizer produces excellent
linearity across the full amplitude range.
MUTE
The output power transistors do not switch while
remains asserted. Unlike the analog mute circuits found on
some amplifiers that can be limited in their attenuation by the
control logic or crosstalk, the mute attenuation on the AD1990
is greater than its dynamic range. The noise floor of the output
MUTE
signal also drops while in
are not switching.
because the output transistors
Power-Up Sequencing
Careful power-up is necessary when using the AD1990 to
ensure correct operation and to avoid possible latch-up issues.
Σ-Δ modulators require feedback to generate an error signal
with respect to the input. The feedback voltages for the AD1990
modulators come from the outputs of the power devices and
before the passive low-pass filters (see Figure 23). This compensates
for nonlinear behavior in the power stage, such as nonoverlap
time, mismatched rise and fall times, and propagation delays. It
also reduces sensitivity to both dc and transient changes of the
power supply voltage.
RESET
MUTE
The AD1990 should be powered up with
held low until all the power supplies have stabilized. Once the
RESET
and
supplies have stabilized, bring the AD1990 out of
RESET
by
bringing
high.
MUTE
Begin the soft unmute sequence by bringing
high at
rising edge. The amplifier produces
RESET
least 1 sec after the
audio using a shorter start-up sequence (as shown in Table 7),
but the amplifier can produce an audible pop or click noise as
the output starts switching. This is because the ac coupling
capacitors at the analog input have a long time constant. If
is deasserted substantially less than 1 sec after deasserting
, then these capacitors may not have charged to a steady
state. They need ample time to settle at a bias voltage of VREF
the reference voltage for the single-ended inputs, or the
amplifier starts with a slight dc offset.
Σ-Δ modulators operate in discrete time. As with all time-
quantized systems, the Nyquist frequency is equal to half of
the sampling frequency and input signals above that point
aliases back into the base band. The AD1990 sampling frequency
(master clock) is equal to half the frequency of the input clock,
approximately 6 MHz, so images only alias for input frequencies
above approximately 3 MHz. This is far enough above the audio
band that bandwidth and aliasing are not a problem in real
applications.
MUTE
RESET
,
GAIN STRUCTURE
Analog Input Levels
The modulator has a noise shaping effect, and SNR is increased
in the audio band by shifting the quantization noise upward in
frequency. For a nominal input clock frequency of 12.288 MHz,
the noise floor rises sharply above 20 kHz. The actual clock
frequency used in an application circuit can deviate from this
rate by as much as 10ꢀ, and the corner frequency of the noise
scales proportionately. The frequency at which the quantization
noise dominates the output determines the amplifier’s practical
bandwidth.
The AD1990 has single-ended inputs for the left and right
channels. The analog input section uses an internal amplifier to
bias the input signal to the reference level, VREF, which is nominally
equal to AVDD/2. A dc-blocking capacitor, as shown in Figure 22,
prevents this bias voltage from affecting the signal source. In
combination with the nominal 20 kΩ input impedance, the value
of this capacitor should be large enough to produce a flat
frequency response at the lowest input frequency of interest.
Rev. 0 | Page 11 of 16
AD1990
Note that the amplifier is capable of dc-coupled operation if the
circuit includes some means to account for this bias voltage.
This fixed total resistance to ground eliminates the last free
variable and gives the following equations for the resistors:
21810
R2 = R4 =
PVDD
+
AINL/
AINR
0V
R1 = R3 = 6000 − R2
Note that the gain previously mentioned applies to each side of
the differential output pair. Therefore, the total forward gain for
the modulator and output stage is twice that value. Recommended
resistor values for some common supply voltages are shown
in Table 10.
Figure 22. AC-Coupled Input Signal
Setting the Modulator Gain
The AD1990 modulator uses a combination of the input signal
and feedback from the power output stage to calculate its two-
state output pattern. The feedback input nodes are part of the
internal analog circuit that operates from the AVDD (nominal
5 V) power supply. Because the voltage measured at the power
outputs is nominally between 0 V and PVDD, and thus beyond
the 0 V to AVDD range, a voltage divider is required to scale the
feedback to an appropriate level.
Table 10. Recommended Feedback Resistor Values
Voltage
Differential
PVDD (V) R1 (kΩ) R2 (kΩ) Divider Gain System Gain
8
10
12
3.27
3.82
±.18
2.73
2.18
1.82
2.2
2.8
3.3
±.± (13.8 dB)
5.6 (17.6 dB)
6.6 (20.8 dB)
Resistor voltage dividers should sense the voltage on each side
of the differential output and provide these feedback signals to
the modulator, as shown in Figure 23.
Programmable Gain Amplifier (PGA)
The Σ-Δ modulator itself requires a fixed gain for a given value
of PVDD to maintain optimal stability. This gain can be appropriate,
but many applications require more gain to account for low
source signal levels. The AD1990 includes a programmable gain
amplifier (PGA) to boost the overall amplifier gain. The total
gain for the amplifier is the product of the modulator gain and
the PGA gain. PGA1 (Pin 31) and PGA0 (Pin 32) select one of
four PGA gain values, as shown in Table 11.
PV
PV
DD
DD
EXTERNAL COMPONENTS
D1
D2
D3
D4
L
R
L
L
OUTx+
OUTx–
C
C
R1
R2
R3
R4
PGND
NFx+
PGND
NFx–
Table 11. PGA Gain Settings
PGA1
PGA0
PGA Gain
1 (0 dB)
2 (6 dB)
± (12 dB)
8 (18 dB)
0
0
1
1
0
1
0
1
Figure 23. H-Bridge Configuration
The resistor values should satisfy the following equation to
maintain modulator stability.
PVDD
3.635
R1+ R2 R3 + R4
Gain =
=
=
R2
R4
The AD1990 incorporates a single-ended-to-differential
converter for each channel in the analog front-end section.
The PGA is also part of this analog front-end, and it affects the
analog input signal before it enters the Σ-Δ modulator. The
PGA1 and PGA0 pins are continuously monitored and allow
the gain to be changed at any time.
Selecting a gain that meets this criterion ensures that the
modulator remains in a stable operating condition.
The ratio of the resistances sets the gain rather than the absolute
values. However, the dividers provide a path from the high
voltage supply to ground; therefore, the values should be large
enough to produce negligible loss due to quiescent current.
The chip contains a calibration circuit to minimize voltage
offsets at the speaker, which helps to minimize clicks and pops
when muting or unmuting. Optimal performance is achieved
for the offset calibration circuit when the feedback divider resistors
sum to 6 kΩ, that is, (R1 + R2) = 6 kΩ, and (R3 + R4) = 6 kΩ.
Rev. 0 | Page 12 of 16
AD1990
Table 12. Nonoverlap Time Settings
POWER STAGE
The H-Bridge
DCTRL2
DCTRL1
DCTRL0
Nonoverlap Time (ns)1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
62
±9
37
2±
15
13.5
12
9
The output stage of the AD1990 includes four integrated
MOSFET devices arranged in a full H-bridge, as shown in
Figure 23. The P-Type, high-side transistor of one leg and the
N-Type, low-side transistor of the opposite leg switch on and off
as a pair producing a total voltage swing across the load of
−PVDD to +PVDD. The drive is floating and differential, and it is
important that neither output terminal be shorted to ground.
The power supply for the output stage of the AD1990, PVDD,
should be in the 8 V to 20 V range and should be capable of
supplying enough current to drive the load. Connect the power
supply across the PVDD and PGND pins. The feedback pins,
NFR+, NFR−, NFL+, and NFL−, supply negative feedback to the
modulator as described in the Setting the Modulator Gain section.
1 Values are typical and are not production tested.
HIGH-SIDE
GATE DRIVE
LOW-SIDE
GATE DRIVE
tNOL
tNOL
For reactive loads, the impedance can only be below the
recommended threshold over a small portion of the amplifier’s
bandwidth. In these cases, the amplifier can enter overcurrent
shutdown in response to even small input signals in those
frequency bands. When designing a system, use the minimum
load impedance over the entire range of amplified frequencies
when calculating current output rather than the average or
nominal load impedance ratings often cited by loudspeaker
driver manufacturers.
Figure 24. Half-Bridge Nonoverlap Delay Timing
The shortest setting (DCTRL[2:0] = 111) or the second shortest
setting (DCTRL[2:0] = 111) is recommended for most applications.
These two settings allow a small trade-off between efficiency
and distortion. Longer nonoverlap times generally increase
distortion while providing little or no decrease in shoot-
through current.
CLOCKING
Output Transistor Nonoverlap Time
The AD1990 Σ-Δ modulator requires an external clock source
with a nominal frequency of 12.288 MHz. This clock can come
from a crystal or from an existing clock signal in the application
circuit. The discrete time portions of the modulator run internally
at 6.144 MHz, corresponding to 128 × fS, where fS = 48 kHz.
The AD1990 allows the user to select from one of eight different
nonoverlap times, as shown in Figure 24. Nonoverlap time
prevents or minimizes the period during which both the high-
side and low-side devices are on simultaneously due to propagation
delays and nonzero rise and fall times. If both the upper and
lower portions of a half-bridge conduct simultaneously, there is a
path directly from the power supply to ground and an induced
current flow known as shoot-through. However, introducing
this delay increases distortion by pushing the switching pattern
further from an ideal two-state waveform. Selecting the
nonoverlap delay requires a compromise between distortion
and efficiency. The logic levels on the three delay control pins,
DCTRL2, DCTRL1, and DCTRL0, set the nonoverlap time
according to Table 12. The state of DCTRL[2:0] is read on the
As mentioned in the Σ-Δ Modulator section, the modulator has
a noise-shaping effect such that SNR is increased within the
audio band by shifting modulator quantization noise upward in
frequency. For an external clock frequency of 12.288 MHz, the
modulator’s noise-shaping works in a manner that results in a
flat noise floor at the amplifier output for frequencies 20 kHz
and below. Above 20 kHz, the amplifier noise rises due to the
spectral shaping of the modulator quantization noise. At very
high frequencies, the noise floor levels off and decreases due to
poles in the modulator noise-transfer function and in the
external LC filter.
RESET
RESET
rising edge of
is logic high.
and should not be changed while
The clock frequency does not have to be exactly equal to
12.288 kHz and can vary by up to 10ꢀ. For other rates, the
noise corner scales linearly with frequency. When the modulator
runs at a rate lower than nominal, the average power stage
switching frequency decreases, the efficiency increases slightly,
and the noise floor begins to rise at a slightly lower frequency.
Likewise, a faster clock gives slightly increased bandwidth and
slightly lower efficiency.
Rev. 0 | Page 13 of 16
AD1990
Using a Crystal Oscillator
Clocking Multiple Amplifiers in Parallel
The AD1990 can use a crystal connected to the CLKI and
CLKO pins as a master clock source, as shown in Figure 25. The
CLKI and CLKO pins connect to an internal inverter to create a
full resonator. The typical values shown work in many applications,
but the crystal manufacturer should provide the exact type and
value of the capacitors and the resistor.
If there are multiple AD199x family amplifiers connected to the
same PVDD supply, use the same clock source (or synchronous
derivatives) for each amplifier as previously described. Avoid
clocking amplifiers from similar but asynchronous clocks if
they use the same power supply because this can result in beat
frequencies.
22pF
XTAL
22pF
PROTECTION CIRCUITS AND ERROR REPORTING
Thermal Protection
47Ω
The AD1990 features thermal protection. When the die
temperature exceeds approximately 135°C, the thermal warning
ERR1
error output (
approximately 150°C, the thermal shutdown error output
ERR2
) is asserted. If the die temperature exceeds
Figure 25. Crystal Connection
(
) is asserted. If this occurs, the part shuts down to
prevent damage to the part. When the die temperature drops
below approximately 120°C, the part returns to normal
operation automatically and negates both error outputs.
Using an External Clock Source
If a clock signal of the appropriate frequency already exists in
the application circuit, connect it directly to CLKI and leave
CLKO floating. The logic levels of the square wave should be
compatible with those defined in Specifications section.
Overcurrent Protection
The AD1990 features over current or short-circuit protection. If
the current through any power transistors exceeds approximately
4 A, the part enters a mute state and the overcurrent error
Large amounts of jitter on the clock input degrade performance.
Whenever possible, avoid passing the clock signal through
programmable logic and other circuits with unknown or variable
propagation delay. In general, clock signals suitable for audio ADCs
or DACs are also appropriate for use with the AD1990.
ERR0
output (
) is asserted. This is a latched error and does not
clear automatically. Restore normal operation and clear the
RESET
error condition by either asserting and then negating
MUTE
or
by asserting and then negating
.
Rev. 0 | Page 1± of 16
AD1990
APPLICATION CIRCUITS
DV
PV
DD
DD
+
+
0.1µF
0.1µF
47µF
1000µF
PV
AV
DD
DD
+
+
0.1µF
10µF
10µF
0.1µF
47µF
AINL
AINR
1000µF
+
+
L
OUTL+
NFL+
C
R1
R2
R2
R1
NFL–
REF_FILT
+
4.7µF
0.1µF
OUTL–
L
L
C
C
AD1990
PGA0
OUTR+
NFR+
PGA1
R1
DCTRL2
DCTRL1
DCTRL0
MUTE
DIGITAL
INPUTS
R2
R2
R1
NFR–
RESET
ERR2
THERMAL SHUTDOWN
THERMAL WARNING
OVERCURRENT
OUTR–
L
ERR1
C
ERR0
R1 = 4.2kΩ
R2 = 1.8kΩ
L = 18µH
CLKI
C = 1µF
LOAD = 6Ω
CLKO
Figure 26. Typical Application Circuit
Rev. 0 | Page 15 of 16
AD1990
OUTLINE DIMENSIONS
0.30
0.25
0.18
9.00
BSC SQ
0.60 MAX
0.60 MAX
PIN 1
INDICATOR
64
49
1
48
PIN 1
INDICATOR
7.25
7.10 SQ
6.95
8.75
BSC SQ
TOP
VIEW
EXPOSED PAD
(BOTTOM VIEW)
0.45
0.40
0.35
33
16
17
32
0.25 MIN
7.50
REF
0.80 MAX
0.65 TYP
1.00
0.85
0.80
12° MAX
0.05 MAX
0.02 NOM
SEATING
PLANE
0.50 BSC
0.20 REF
COMPLIANT TO JEDEC STANDARDS MO-220-VMMD-4
Figure 27. 64-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
9 mm × 9 mm Body, Very Thin Quad
(CP-64-3)
Dimensions shown in millimeters
ORDERING GUIDE
Model
Temperature Range
Package Description
Package Option
CP-6±-3
CP-6±-3
AD1990ACPZ1
AD1990ACPZRL1
−±0°C to +85°C
−±0°C to +85°C
AD1990ACPZRL71 −±0°C to +85°C
6±-Lead Lead Frame Chip Scale Package (LFCSP_VQ)
6±-Lead Lead Frame Chip Scale Package (LFCSP_VQ), 13”Tape and Reel
6±-Lead Lead Frame Chip Scale Package (LFCSP_VQ), 7”Tape and Reel
Evaluation Board
CP-6±-3
EVAL-AD1990EB
1 Z = Pb-free part.
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05380-0-4/06(0)
Rev. 0 | Page 16 of 16
相关型号：
©2020 ICPDF网 联系我们和版权申明