EVAL-AD7723CB [ADI]
16-Bit, 1.2 MSPS CMOS, Sigma-Delta ADC; 16位, 1.2 MSPS CMOS , Σ-Δ ADC型号: | EVAL-AD7723CB |
厂家: | ADI |
描述: | 16-Bit, 1.2 MSPS CMOS, Sigma-Delta ADC |
文件: | 总32页 (文件大小:751K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
16-Bit, 1.2 MSPS CMOS,
Sigma-Delta ADC
AD7723
FEATURES
FUNCTIONAL BLOCK DIAGRAM
16-bit Σ-∆ ADC
REF2
REF1
2.5V
REFERENCE
AV
DD
AD7723
1.2 MSPS output word rate
32×/16× oversampling ratio
Low-pass and band-pass digital filter
Linear phase
AGND
VIN(+)
VIN(–)
FIR
FILTER
DV
DD
DGND
MODULATOR
On-chip 2.5 V voltage reference
Standby mode
Flexible parallel or serial interface
Crystal oscillator
XTAL_OFF
XTAL
CLKIN
UNI
HALF_PWR
STBY
XTAL
CLOCK
MODE 1
DGND/DB15
DGND/DB14
MODE 2
SCR/DB13
SLDR/DB12
SLP/DB11
TSI/DB10
FSO/DB9
SYNC
Single 5 V supply
DV /CS
DD
CONTROL
LOGIC
CFMT/RD
DGND/DRDY
DGND/DB0
GENERAL DESCRIPTION
The AD7723 is a complete 16-bit, sigma-delta ADC. The part
operates from a 5 V supply. The analog input is continuously
sampled, eliminating the need for an external sample-and-hold.
The modulator output is processed by a finite impulse response
(FIR) digital filter. The on-chip filtering combined with a high
oversampling ratio reduces the external antialias requirements
to first order in most cases. The digital filter frequency response
can be programmed to be either low-pass or band-pass.
DGND/ DGND/ DGND/ DOE/ SFMT/ FSI/ SCO/ SDO/
DB1
DB2 DB3 DB4 DB5 DB6 DB7 DB8
Figure 1.
The part provides an on-chip 2.5 V reference. Alternatively, an
external reference can be used.
A power-down mode reduces the idle power consumption
to 200 µW.
The AD7723 provides 16-bit performance for input bandwidths
up to 460 kHz at an output word rate up to 1.2 MHz. The
sample rate, filter corner frequencies, and output word rate are
set by the crystal oscillator or external clock frequency.
The AD7723 is available in a 44-lead MQFP package and is
specified over the industrial temperature range from
–40°C to +85°C.
Data can be read from the device in either serial or parallel
format. A stereo mode allows data from two devices to share a
single serial data line. All interface modes offer easy, high speed
connections to modern digital signal processors.
Two input modes are provided, allowing both unipolar and
bipolar input ranges.
Rev. C
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2005 Analog Devices, Inc. All rights reserved.
AD7723
TABLE OF CONTENTS
Specifications..................................................................................... 3
Timing Specifications....................................................................... 6
Absolute Maximum Ratings.......................................................... 10
ESD Caution................................................................................ 10
Pin Configuration And Function Descriptions.......................... 11
Terminology .................................................................................... 14
Typical Performance Characteristics ........................................... 15
Circuit Description......................................................................... 18
Applying the AD7723 .................................................................... 20
Analog Input Range ................................................................... 20
Analog Input ............................................................................... 20
Driving the Analog Inputs ........................................................ 20
Applying the Reference.............................................................. 21
Clock Generation ....................................................................... 22
System Synchronization ................................................................ 23
Data Interfacing.............................................................................. 24
Parallel Interface......................................................................... 24
Serial Interface ................................................................................ 25
Two-Channel Multiplexed Operation ..................................... 25
Serial Interface to DSPs ................................................................. 27
AD7723 to ADSP-21xx Interface ............................................. 27
AD7723 to SHARC Interface.................................................... 27
AD7723 to DSP56002 Interface ............................................... 27
AD7723 to TMS320C5x Interface............................................ 27
Grounding and Layout .................................................................. 28
Outline Dimensions....................................................................... 29
Ordering Guide .......................................................................... 29
REVISION HISTORY
5/05—Rev. B to Rev. C
9/02—Data Sheet changed from Rev. 0 to Rev. A
Changes to Format .............................................................Universal
Changes to Figure 6.......................................................................... 8
Changes to System Synchronization............................................ 23
Updated Outline Dimensions....................................................... 29
Changes to the Ordering Guide.................................................... 29
New TPCs 1 and 2 Added ............................................................. 13
Edits to Figures 17 and 18 ............................................................. 18
Outline Dimensions Updated....................................................... 23
10/03—Rev. A to Rev. B
Changes to Ordering Guide ............................................................ 8
Outline Dimensions Updated....................................................... 23
Rev. C | Page 2 of 32
AD7723
SPECIFICATIONS1
AVDD = DVDD = 5 V 5ꢀ; AGND = AGND1 = AGND2 = DGND = 0 V; fCLKIN = 19.2 MHz; REF2 = 2.5 V; TA = TMIN to TMAX, unless
otherwise noted.
Table 1.
B Version
Parameter
DYNAMIC SPECIFICATIONS2, 3
Test Conditions/Comments
HALF_PWR = 0 to 1
Min
Typ
Max
Unit
fCLKIN = 10 MHz when HALF_PWR = 1
Decimate by 32
Bipolar Mode
Signal to Noise
Full Power
2.5 V reference
3 V reference
87
88.5
86.5
90
91
89
−96
dB
dB
dB
dB
dB
dB
Half Power
Total Harmonic Distortion4
Spurious-Free Dynamic Range4
−90
−92
−90
2.5 V reference
3 V reference
Unipolar Mode
Signal to Noise
Total Harmonic Distortion4
Spurious-Free Dynamic Range4
Band-Pass Filter Mode
Bipolar Mode
87
−89
−90
dB
dB
dB
Signal to Noise
76
79
dB
Decimate by 16
Bipolar Mode
Signal to Noise
Measurement bandwidth = 0.383 × FO
2.5 V reference
82
83
78
86
87
81.5
dB
dB
dB
dB
dB
dB
dB
3 V reference
Measurement bandwidth = 0.5 × FO
2.5 V reference
3 V reference
2.5 V reference
Signal to Noise
Total Harmonic Distortion4
Spurious-Free Dynamic Range4
−88
−86
−90
−88
3 V reference
Unipolar Mode
Signal to Noise
Signal to Noise
Measurement bandwidth = 0.383 × FO
Measurement bandwidth = 0.5 × FO
84
81
−89
dB
dB
dB
Total Harmonic Distortion4
DIGITAL FILTER RESPONSE
Low-Pass Decimate by 32
0 kHz to fCLKIN/83.5
fCLKIN/66.9
0.001
dB
dB
dB
dB
−3
−6
fCLKIN/64
fCLKIN/51.9 to fCLKIN/2
Group Delay
−90
1293/2 fCLKIN
1293/fCLKIN
Settling Time
Rev. C | Page 3 of 32
AD7723
B Version
Typ
Parameter
Test Conditions/Comments
Min
Max
0.001
Unit
Low-Pass Decimate by 16
0 kHz to fCLKIN/41.75
fCLKIN/33.45
fCLKIN/32
fCLKIN/25.95 to fCLKIN/2
Group Delay
dB
dB
dB
dB
−3
−6
−90
541/2 fCLKIN
541/fCLKIN
Settling Time
Band-Pass Decimate by 32
fCLKIN/51.90 to fCLKIN/41.75
fCLKIN/62.95, fCLKIN/33.34
fCLKIN/64, fCLKIN/32
0 kHz to fCLKIN/83.5, fCLKIN/25.95 to fCLKIN/2
Group Delay
0.001
dB
dB
dB
dB
−3
−6
−90
1293/2 fCLKIN
1293/fCLKIN
Settling Time
Output Data Rate, FO
Decimate by 32
Decimate by 166
fCLKIN/32
fCLKIN/16
ANALOG INPUTS
Full-Scale Input Span
Bipolar Mode
Unipolar Mode
Absolute Input Voltage
Input Sampling Capacitance
Input Sampling Rage, fCLKIN
CLOCK
VIN(+) − VIN(−)
VIN(+) − VIN(−)
4/5 × VREF2
8/5 × VREF2
AVDD
V
V
V
pF
MHz
0
AGND
2
3
19.2
55
CLKIN Duty Ratio
45
%
REFERENCE
REF1 Output Resistance
Using Internal Reference
REF2 Output Voltage
REF2 Output Voltage Drift
Using External Reference
REF2 Input Impedance
REF2 External Voltage Range
STATIC PERFORMANCE
Resolution
Differential Nonlinearity
Integral Nonlinearity
DC CMRR
Offset Error
Gain Error5
kΩ
2.39
2.54
60
2.69
V
ppm/°C
REF1 = AGND
4
2.5
kΩ
V
1.2
16
3.15
1
Bits
LSB
LSB
dB
mV
% FSR
Guaranteed monotonic
0.5
2
80
20
0.5
LOGIC INPUTS (EXCLUDING CLKIN)
VINH, Input High Voltage
VINL, Input High Voltage
CLOCK INPUT (CLKIN)
VINH, Input High Voltage
VINL, Input High Voltage
ALL LOGIC INPUTS
IIN, Input Current
2.0
3.8
V
V
0.8
0.4
V
V
VIN = 0 V to DVDD
10
10
µA
pF
CIN, Input Capacitance
Rev. C | Page 4 of 32
AD7723
B Version
Parameter
Test Conditions/Comments
Min
Typ
Max
Unit
LOGIC OUPUTS
VOH, Output High Voltage
VOL, Output Low Voltage
POWER SUPPLIES
AVDD
|IOUT| = 200 µA
|IOUT| = 1.6 mA
4.0
V
V
0.4
4.75
4.75
5.25
60
33
5.25
35
20
V
IAVDD
HALF_PWR = Logic Low
HALF_PWR = Logic High
50
25
mA
mA
V
mA
mA
µW
DVDD
IDVDD
HALF_PWR = Logic Low
HALF_PWR = Logic High
Standby Mode
25
15
Power Consumption6
200
1 Operating temperature range is −40°C to +85°C (B: Version).
2 Typical values for SNR apply for parts soldered directly to the PCB ground plane.
3 Dynamic specifications apply for input signal frequencies from dc to 0.0240 × fCLKIN in decimate by 16 mode and from dc to 0.0120 × fCLKIN in decimate by 32 mode.
4 When using the internal reference, THD and SFDR specifications apply only to input signals above 10 kHz with a 10 µF decoupling capacitor between REF2 and
AGND2. At frequencies below 10 kHz, THD degrades to 84 dB and SFDR degrades to 86 dB.
5 Gain error excludes reference error.
6 CLKIN and digital inputs static and equal to 0 or DVDD
.
Rev. C | Page 5 of 32
AD7723
TIMING SPECIFICATIONS
AVDD = DVDD = 5 V 5ꢀ; AGND = AGND1 = DGND = 0 V; fCLKIN = 19.2 MHz; CL = 50 pF; SFMT = logic low or high, CFMT = logic low
or high; TA = TMIN to TMAX, unless otherwise noted.
Table 2.
Parameter
Symbol
fCLK
t1
t2
t3
Min
Typ
Max
Unit
MHz
µs
CLKIN Frequency
CLKIN Period (tCLK – 1/fCLK
CLKIN Low Pulse Width
CLKIN High Pulse Width
CLKIN Rise Time
1
19.2
1
0.55 × t1
0.55 × t1
)
0.052
0.45 × t1
0.45 × t1
5
5
0
0
t4
t5
ns
ns
CLKIN Fall Time
FSI Setup Time
FSI Hold Time
FSI High Time1
CLKIN to SCO Delay
SCO Period2, SCR = 1
SCO Period2, SCR = 0
SCO Transition to FSO High Delay
SCO Transition to FSO Low Delay
SCO Transition to SDO Valid Delay
SCO Transition from FSI3
t6
t7
t8
t9
5
5
1
40
ns
ns
tCLK
ns
tCLK
tCLK
ns
25
2
1
0
0
5
60
5
t10
t10
t11
t12
t13
t14
t15
t16
t17
t18
t19
t20
t21
t22
t23
t24
t25
t26
t27
t28
5
5
ns
ns
12
tCLK + t2
20
SDO Enable Delay Time
SDO Disable Delay Time
ns
ns
5
20
2
DRDY
2
tCLK
tCLK
ns
High Time
Conversion Time2 (Refer to Table 3 and Table 4)
16/32
DRDY
35
20
50
35
CLKIN to
Transition
CLKIN to DATA Valid
ns
ns
CS RD
0
/
Setup Time to CLKIN
Hold Time to CLKIN
CS RD
/
20
ns
Data Access Time
Bus Relinquish Time
20
20
35
35
ns
ns
SYNC Input Pulse Width
SYNC Low Time before CLKIN Rising
1
0
tCLK
ns
ns
DRDY
DRDY
25
35
High Delay after Rising SYNC
Low Delay after SYNC Low
2049
tCLK
1 FSO pulses are gated by the release of FSI (going low).
2 Guaranteed by design.
3 Frame sync is initiated on the falling edge of CLKIN.
I
OL
1.6mA
TO
OUTPUT
PIN
1.6V
C
L
50pF
I
OH
200µA
Figure 2. Load Circuit for Timing Specifications
Rev. C | Page 6 of 32
AD7723
t5
t4
t2
2.3V
CLKIN
FSI
0.8V
t3
t1
t7
t6
t8
t9
SCO
t9
t10
Figure 3. Serial Mode Timing for Clock Input, Frame Sync Input, and Serial Clock Output
32 CLKIN CYCLES
CLKIN
t8
FSI
(SFMT = 1)
t14
SCO
(CFMT = 0)
t11
FSO
(SFMT = 0)
t11
t12
FSO
(SFMT = 1)
t13
D15
D14
D13
D2
D1
D0
D15
D14
SDO
Figure 4. Serial Mode 1: Timing for Frame Sync Input, Frame Sync Output, Serial Clock Output, and Serial Data Output (See Table 3 for Control Inputs, TSI = DOE)
32 CLKIN CYCLES
CLKIN
t8
FSI
t14
SCO
(CFMT = 0)
t11
t12
FSO
t13
SDO
D2
D1
D0
D15
D14
D13
D12
D11
D5
D3
D2
D1
D0
D15
D14
D4
Figure 5. Serial Mode 2: Timing for Frame Sync Input, Frame Sync Output, Serial Clock Output, and Serial Data Output (See Table 3 for Control Inputs, TSI = DOE)
Rev. C | Page 7 of 32
AD7723
32 CLKIN CYCLES
CLKIN
FSI
t8
t14
SCO
(CFMT = 0)
t12
t11
16 CLKIN CYCLES
16 CLKIN CYCLES
FSO
t13
D15
D3
D14
D0
D15
D1
D0
SDO
D2
D1
D13
D3
D2
D15
D14
D13
D3
D2
D1
D0
Figure 6. Serial Mode 3: Timing for Frame Sync Input, Frame Sync Output, Serial Clock Output, and Serial Data Output (See Table 3 for Control Inputs, TSI = DOE)
Table 3. Serial Interface (MODE1 = 0, MODE2 = 0)
Control Inputs
Serial Mode Decimation Ratio (SLDR) Digital Filter Mode (SLP) SCO Frequency (SCR) Output Data Rate SLDR SLP SCR
1
1
2
2
3
32
32
32
32
16
Low Pass
Band Pass
Low Pass
Band Pass
Low Pass
fCLKIN
fCLKIN
fCLKIN/2
fCLKIN/2
fCLKIN
fCLKIN/32
fCLKIN/32
fCLKIN/32
fCLKIN/32
fCLKIN/16
1
1
1
1
0
1
0
1
0
1
0
0
1
1
0
Table 4. Parallel Interface
Control Inputs
Digital Filter Mode
Band Pass
Low Pass
Decimation Ratio
Output Data Rate
fCLKIN/32
fCLKIN/32
MODE1
MODE2
32
32
16
0
1
1
1
0
1
Low Pass
fCLKIN/16
DOE
t16
t15
SDO
Figure 7. Serial Mode Timing for Data Output Enable and Serial Data Output
Rev. C | Page 8 of 32
AD7723
t18
CLKIN
DRDY
t19
t19
t17
t20
WORD N
DB0–DB15
WORD N – 1
WORD N + 1
CS
RD
Tied Logic Low
Figure 8. Parallel Mode Read Timing, and
CLKIN
DRDY
t18
t19
t19
t
22
RD/CS
t21
t22
t21
t24
DB0–DB15
VALID DATA
t23
CS RD
=
Figure 9. Parallel Mode Read Timing,
t28
CLKIN
t26
SYNC
DRDY
t25
t27
Figure 10. SYNC Timing
Rev. C | Page 9 of 32
AD7723
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 5.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Parameter
Rating
DVDD to DGND
−0.3 V to +7 V
AVDD, AVDD1 to AGND
AVDD, AVDD1 to DVDD
AGND, AGND1 to DGND
Digital Inputs to DGND
Digital Outputs to DGND
VIN (+), VIN(−) to AGND
REF1 to AGND
−0.3 V to +7 V
−1 V to +1 V
−0.3 V to +0.3 V
−0.3 V to DVDD + 0.3 V
−0.3 V to DVDD + 0.3 V
−0.3 V to AVDD + 0.3 V
−0.3 V to AVDD + 0.3 V
−0.3 V to AVDD + 0.3 V
−40°C to +85°C
−65°C to +150°C
150°C
REF2 to AGND
Operating Temperature Range
Storage Temperature Range
Junction Temperature
θJA Thermal Impedance
Lead Temperature, Soldering
Vapor Phase (60 sec)
Infrared (15 sec)
95°C/W
215°C
220°C
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate
on the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. C | Page 10 of 32
AD7723
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
44 43 42 41 40 39 38 37 36 35 34
1
33
32
31
DGND/DB2
SCR/DB13
PIN 1
IDENTIFIER
2
3
DGND/DB1
DGND/DB0
DGND/DB14
DGND/DB15
4
30
29
28
27
26
25
24
CFMT/RD
DGND/DRDY
DGND
DV /CS
DD
5
SYNC
DGND
STBY
AD7723
6
TOP VIEW
(Not to Scale)
7
MODE2
8
AV
DD
MODE1
AGND1
AGND1
9
AGND
UNI
10
11
23 REF2
AV
DD1
12 13 14 15 16 17 18 19 20 21 22
Figure 11. 44-Lead MQFP
Table 6. Pin Function Descriptions
Pin No.
Mnemonic
Description
6, 28
DGND
Ground Reference for Digital Circuitry.
8, 7
MODE1/MODE2 Mode Control Inputs. The MODE1 and MODE2 pins choose either parallel or serial data interface operation
and select the operating mode for the digital filter in parallel mode. See Table 3 and Table 4.
9, 10
11
AGND1
AVDD1
Digital Logic Power Supply Ground for the Analog Modulator.
Digital Logic Power Supply Voltage for the Analog Modulator.
12
CLKIN
Clock Input. An external clock source can be applied directly to this pin with XTAL_OFF tied high.
Alternatively, a parallel resonant fundamental frequency crystal, in parallel with a 1 MΩ resistor, can
be connected betweenthe XTAL pin and the CLKIN pin with XTAL_OFF tied low. External capacitors
are then required from the CLKIN and XTAL pins to ground. Consult the crystal manufacturer’s
recommendation for the load capacitors.
13
14
XTAL
XTAL_OFF
Input to Crystal Oscillator Amplifier. If an external clock is used, XTAL should be tied to AGND1.
Oscillator Enable Input. A logic high disables the crystal oscillator amplifier to allow use of an external
clock source. Set low when using an external crystal between the CLKIN and XTAL pins.
15
HALF_PWR
When set high, the power dissipation is reduced by approximately one-half, and a maximum CLKIN
frequency of 10 MHz applies.
16, 18, 25 AGND
Power Supply Ground for the Analog Modulator.
Positive Power Supply Voltage for the Analog Modulator.
Negative Terminal of the Differential Analog Input.
Positive Terminal of the Differential Analog Input.
Reference Output. REF1 connects through 3 kΩ to the output of the internal 2.5 V reference and to a buffer
amplifier that drives the Σ-∆ modulator.
17, 26
19
AVDD
VIN(−)
VIN(+)
REF1
20
21
22
23
AGND2
REF2
Power Supply Ground Return to the Reference Circuitry, REF2, of the Analog Modulator.
Reference Input. REF2 connects to the output of an internal buffer amplifier that drives the Σ-∆ modulator.
When REF2 is used as an input, REF1 must be connected to AGND to disable the internal buffer amplifier.
24
27
UNI
Analog Input Range Select Input. The UNI pin selects the analog input range for either bipolar or unipolar
operation. A logic high input selects unipolar operation and a logic low selects bipolar operation.
Standby Logic Input. A logic high sets the AD7723 into the power-down state.
STBY
Rev. C | Page 11 of 32
AD7723
Pin No.
Mnemonic
Description
29
SYNC
Synchronization Logic Input. When using more than one AD7723 operated from a common master clock,
SYNC allows each ADC to simultaneously sample its analog input and update its output register. A rising
edge resets the AD7723 digital filter sequencer counter to 0. When the rising edge of CLKIN senses a logic
low on SYNC, the reset state is released. Because the digital filter and sequencer are completely reset
during this action, SYNC pulses cannot be applied continuously.
39
DVDD
Digital Power Supply Voltage; 5 V 5%.
Table 7. Parallel Mode Pin Function Descriptions
Pin
No.
Mnemonic
DGND/DB2
DGND/DB1
DGND/DB0
CFMT/RD
Description
1
2
3
4
Data Output Bit.
Data Output Bit.
Data Output Bit (LSB).
Read Logic Input. Used in conjunction with CS to read data from the parallel bus. The output data bus is enabled
when the rising edge of CLKIN senses a logic low level on RD if CS is also low. When RD is sensed high, the output
data bits, DB15 to DB0, are high impedance.
5
DGND/DRDY Data Ready Logic Output. A falling edge indicates a new output word is available to be read from the output data
register. DRDY returns high upon completion of a read operation. If a read operation does not occur between output
updates, DRDY pulses high for two CLKIN cycles before the next output update. DRDY also indicates when
conversion results are available after a SYNC sequence.
30
31
32
33
34
35
36
37
38
40
41
42
43
44
DVDD/CS
Chip Select Logic Input.
DGND/DB15 Data Output Bit (MSB).
DGND/DB14 Data Output Bit.
SCR/DB13
SLDR/DB12
SLP/DB11
TSI/DB10
FSO/DB9
SDO/DB8
SCO/DB7
FSI/DB6
Data Output Bit.
Data Output Bit.
Data Output Bit.
Data Output Bit.
Data Output Bit.
Data Output Bit.
Data Output Bit.
Data Output Bit.
Data Output Bit.
Data Output Bit.
Data Output Bit.
SFMT/DB5
DOE/DB4
DGND/DB3
Rev. C | Page 12 of 32
AD7723
Table 8. Serial Mode Pin Function Descriptions
Pin
No.
Mnemonic
DGND/DB2
DGND/DB1
DGND/DB0
CFMT/RD
Description
Tie to DGND.
Tie to DGND.
Tie to DGND.
1
2
3
4
Serial Clock Format Logic Input. The clock format pin selects whether the serial data, SDO, is valid on the rising or
falling edge of the serial clock, SCO. When CFMT is logic low, serial data is valid on the falling edge of the serial clock,
SCO. If CFMT is logic high, SDO is valid on the rising edge of SCO.
5
DGND/DRDY Tie to DGND.
DVDD/CS
Tie to DVDD.
30
31
32
33
DGND/DB15 Tie to DGND.
DGND/DB14 Tie to DGND.
SCR/DB13
Serial Clock Rate Select Input. With SCR set logic low, the serial clock output frequency, SCO, is equal to the CLKIN
frequency. A logic high sets it equal to one-half the CLKIN frequency.
34
SLDR/DB12
Serial Mode Low/High Output Data Rate Select Input. With SLDR set logic high, the low data rate is selected. A logic
low selects the high data rate. The high data rate corresponds to data at the output of the fourth decimation filter
(decimate by 16). The low data rate corresponds to data at the output of the fifth decimation filter (decimate by 32).
35
36
SLP/DB11
TSI/DB10
Serial Mode Low-Pass/Band-Pass Filter Select Input. With SLP set logic high, the low-pass filter response is selected.
A logic low selects band-pass.
Time Slot Logic Input. The logic level on TSI sets the active state of the DOE pin. With TSI set logic high, DOE enables
the SDO output buffer when it is a logic high and vice versa. TSI is used when two AD7723s are connected to the
same serial data bus. When this function is not needed, TSI and DOE should be tied low.
37
38
FSO/DB9
SDO/DB8
Frame Sync Output. FSO indicates the beginning of a word transmission on the SDO pin. Depending on the logic
level of the SFMT pin, the FSO signal is either a positive pulse approximately one SCO period wide or a frame pulse
that is active low for the duration of the 16-data bit transmission.
Serial Data Output. The serial data is shifted out MSB first, synchronous with the SCO. Serial Mode 1 data
transmissions last 32 SCO cycles. After the LSB is output, trailing zeros are output for the remaining 16 SCO cycles.
Serial Modes 2 and 3 data transmissions last 16 SCO cycles.
40
41
SCO/DB7
FSI/DB6
Serial Clock Output.
Frame Synchronization Logic Input. The FSI input is used to synchronize the AD7723 serial output data register to an
external source and to allow more than one AD7723, operated from a common master clock, to simultaneously
sample its analog input and update its output register.
42
43
44
SFMT/DB5
DOE/DB4
Serial Data Format Logic Input. The logic level on the SFMT pin selects the format of the FSO signal for Serial Mode 1.
A logic low makes the FSO output a pulse one SCO cycle wide at the beginning of a serial data transmission. With
SFMT set to a logic high, the FSO signal is a frame pulse that is active low for the duration of the 16-bit transmission.
For Serial Modes 2 and 3, SFMT should be tied high.
Data Output Enable Logic Input. The DOE pin controls the three-state output buffer of the SDO pin. The active state
of DOE is determined by the logic level on the TSI pin. When the DOE logic level equals the level on the TSI pin, the
serial data output, SDO, is active. Otherwise, SDO is high impedance. SDO can be three-state after a serial data
transmission by connecting DOE to FSO. In normal operations, TSI and DOE should be tied low.
DGND/DB3
Tie to DGND.
Rev. C | Page 13 of 32
AD7723
TERMINOLOGY
Signal-to-Noise Ratio (SNR)
Integral Nonlinearity
SNR is the measured signal-to-noise ratio at the output of the
ADC. The signal is the rms magnitude of the fundamental.
Noise is the rms sum of all of the nonfundamental signals up to
half the output data rate (FO/2), excluding dc. The ADC is
evaluated by applying a low noise, low distortion sine wave
signal to the input pins. By generating a fast fourier transform
(FFT) plot, the SNR data can then be obtained from the output
spectrum.
This is the maximum deviation of any code from a straight line
passing through the endpoints of the transfer function. The
endpoints of the transfer function are minus full scale, a point
0.5 LSB below the first code transition (100 . . . 00 to 100 . . . 01
in bipolar mode, 000 . . . 00 to 000 . . . 01 in unipolar mode),
and plus full scale, a point 0.5 LSB above the last code transition
(011 . . . 10 to 011 . . . 11 in bipolar mode, 111 . . . 10 to 111 . . .
11 in unipolar mode). The error is expressed in LSBs.
Total Harmonic Distortion (THD)
Differential Nonlinearity
THD is the ratio of the rms sum of the harmonics to the rms
value of the fundamental. THD is defined as
This is the difference between the measured and the ideal 1 LSB
change between two adjacent codes in the ADC.
2
Common-Mode Rejection Ratio
V22 +V32 +V42 +V5 2 +V6
THD = 20log
The ability of a device to reject the effect of a voltage applied to
both input terminals simultaneously—often through variation
of a ground level—is specified as a common–mode rejection
ratio. CMRR is the ratio of gain for the differential signal to the
gain for the common-mode signal.
V1
where V1 is the rms amplitude of the fundamental, and V2, V3,
V4, V5, and V6 are the rms amplitudes of the second through
sixth harmonics. The THD is also derived from the FFT plot of
the ADC output spectrum.
Unipolar Offset Error
Unipolar offset error is the deviation of the first code transition
(10 . . . 000 to 10 . . . 001) from the ideal differential voltage
(VIN(+) – VIN(–)+ 0.5 LSB) when operating in the unipolar
mode.
Spurious-Free Dynamic Range (SFDR)
Defined as the difference, in dB, between the peak spurious or
harmonic component in the ADC output spectrum (up to FO/2
and excluding dc) and the rms value of the fundamental.
Normally, the value of this specification is determined by the
largest harmonic in the output spectrum of the FFT. For input
signals whose second harmonics occur in the stop-band region
of the digital filter, the spur in the noise floor limits the SFDR.
Bipolar Offset Error
This is the deviation of the midscale transition code (111 . . . 11
to 000 . . . 00) from the ideal differential voltage (VIN(+) –
VIN(–) – 0.5 LSB) when operating in the bipolar mode.
Pass-Band Ripple
The frequency response variation of the AD7723 in the defined
pass-band frequency range.
Gain Error
The first code transition should occur at an analog value ½ LSB
above –full scale. The last transition should occur for an analog
value 1 ½ LSB below the nominal full scale. Gain error is the
deviation of the actual difference between first and last code
transitions and the ideal difference between first and last code
transitions.
Pass-Band Frequency
The frequency up to which the frequency response variation is
within the pass-band ripple specification.
Cutoff Frequency
The frequency below which the AD7723’s frequency response
will not have more than 3 dB of attenuation.
Stop-Band Frequency
The frequency above which the AD7723’s frequency response
will be within its stop-band attenuation.
Stop-Band Attenuation
The AD7723’s frequency response will not have less than 90 dB
of attenuation in the stated frequency band.
Rev. C | Page 14 of 32
AD7723
TYPICAL PERFORMANCE CHARACTERISTICS
AVDD = DVDD = 5 V; TA = 25°C; CLKIN = 19.2 MHz; external 2.5 V reference, unless otherwise noted.
106
104
102
100
98
110
100
90
SIGNAL FREQUENCY = 98kHz
MEASUREMENT BANDWIDTH = 300kHz
SIGNAL FREQUENCY = 98kHz
MEASUREMENT BANDWIDTH = 460kHz
3RD
THD
80
SFDR
96
70
2ND
THD
94
SNR
60
92
SNR
50
90
88
–50
40
–50
–25
0
25
50
75
100
–40
–30
–20
–10
0
TEMPERATURE (°C)
ANALOG INPUT LEVEL (dB)
Figure 15. SNR and THD vs. Temperature (Output Data Rate = 600 kHz)
Figure 12. SNR, THD, and SFDR vs. Analog Input Level Relative to Full Scale
(Output Data Rate = 1.2 MHz)
110
106
SIGNAL FREQUENCY = 98kHz
MEASUREMENT BANDWIDTH = 300kHz
100
104
SFDR
102
100
90
THD
THD
98
80
96
SFDR
INPUT SIGNAL = 10kHz
MEASUREMENT BANDWIDTH = 0.383 × OWR
94
70
SNR
92
90
60
50
40
88
SNR
86
84
–50
–40
–30
–20
0
–10
100
500
1000
1500
2150
ANALOG INPUT LEVEL (dB)
OUTPUT WORD RATE (kHz)
Figure 13. SNR, THD, and SFDR vs. Analog Input Level Relative to Full Scale
(Output Data Rate = 600 kHz)
Figure 16. SNR, THD, and SFDR vs. Sampling Frequency (Decimate by 16)
102
115
SIGNAL FREQUENCY = 98kHz
MEASUREMENT BANDWIDTH = 460kHz
INPUT SIGNAL = 10kHz
MEASUREMENT BANDWIDTH = 0.5 × OWR
100
3RD
110
98
SFDR
2ND
THD
96
94
92
90
88
86
84
105
100
THD
95
SNR
SNR
90
–25
0
25
50
75
100
–50
50
150
300
450
600
750
900
TEMPERATURE (°C)
OUTPUT WORD RATE (kHz)
Figure 14. SNR and THD vs. Temperature (Output Data Rate = 1.2 MHz)
Figure 17. SNR, THD, and SFDR vs. Sampling Frequency (Decimate by 32)
Rev. C | Page 15 of 32
AD7723
R
220Ω
2000
FB
V
(+) = V (–)
IN
IN
8192 SAMPLES TAKEN
R
R
390Ω
SOURCE
IN
1800
1600
1400
1200
1000
800
AIN = ±2V
BIASED
ABOUT
AD8047
A1
50Ω
27Ω
20
VIN(+)
GROUND
R
BALANCE2
R
BALANCE1
220Ω
220Ω
220pF
R
BALANCE2
AD7723
220Ω
R
27Ω
REF1
10kΩ
19
23
VIN(–)
REF2
A2
600
AD8047
R
REF2
20kΩ
220nF
10nF
400
21
REF1
200
0
GAIN = 2 × R /(R + R
)
FB
IN
SOURCE
1µF
R
= R
× (R + R
)/R
SOURCE
)/(2 × R
)
FB
BALANCE1
BALANCE2
IN
SOURCE
FB
R
= R
× (R + R
IN
32700
32702
32704
32706
CODE
32708
32710 32712 32713
REF2
REF1
Figure 21. Differential Nonlinearity (Output Data Rate = 600 kHz)
Figure 18. Histogram of Output Codes with DC Input
(Output Data Rate = 1.2 MHz)
5000
4500
4000
3500
3000
2500
2000
1500
1000
1.0
V
(+) = V (–)
IN
IN
8192 SAMPLES TAKEN
67108864 SAMPLES TAKEN
0.8 DIFFERENTIAL MODE
0.6
0.4
0.2
0
–0.2
–0.4
–0.6
–0.8
–1.0
500
0
0
32703
32704
32705
32706
CODE
32707
32708 32709 32710
16384
32768
CODE
49152
65535
Figure 22. Integral Nonlinearity (Output Data Rate =1.2 MHz)
Figure 19. Histogram of Output Codes with DC Input
(Output Data Rate = 600 kHz)
1.0
1.0
67108864 SAMPLES TAKEN
0.8 DIFFERENTIAL MODE
67108864 SAMPLES TAKEN
DIFFERENTIAL MODE
0.8
0.6
0.6
0.4
0.4
0.2
0.2
0
0
–0.2
–0.4
–0.6
–0.8
–1.0
–0.2
–0.4
–0.6
–0.8
–1.0
0
16384
32768
CODE
49152
65535
0
16384
32768
CODE
49152
65535
Figure 23. Integral Nonlinearity (Output Data Rate = 600 kHz)
Figure 20. Differential Nonlinearity (Output Data Rate = 1.2 MHz)
Rev. C | Page 16 of 32
AD7723
0
225
SNR = –89.91dB
SNR + D = –89.7dB
THD = –101.16dB
SFDR = –102.1dB
2ND HARMONIC = –102.1dB
3RD HARMONIC = –110.3dB
200
175
150
–20
–40
AI (HALF_POWER = 0)
DD
A
= 50kHz
IN
MEASURED BW = 300kHz
–60
125
100
75
–80
AI (HALF_POWER = 1)
DD
–100
DI
DD
–120
–140
–160
50
25
0
0
5
10
15
20
25
150k
100k
FREQUENCY (Hz)
200k
250k
300k
0
50k
CLOCK FREQUENCY (MHz)
Figure 24. Power Consumption vs. CLKIN Frequency
Figure 26. 16 K Point FFT (Output Data Rate = 600 kHz)
0
SNR = –86.19dB
SNR + D = –85.9dB
THD = –96.42dB
SFDR = –99.61dB
2ND HARMONIC = –100.98dB
3RD HARMONIC = –99.61dB
–25
–50
A
= 100kHz
IN
MEASURED BW = 460kHz
–75
–100
–125
–150
300k
400k
500k
600k
0
100k
200k
FREQUENCY (Hz)
Figure 25. 16 K Point FFT (Output Data Rate = 1.2 MHz)
Rev. C | Page 17 of 32
AD7723
CIRCUIT DESCRIPTION
the converter is 16. Data fed to the interface from the output of
the fifth filter results in an output data rate of fCLKIN/32 and a
corresponding OSR for the converter of 32. When an output
data rate (ODR) of fCLKIN/32 is selected, the digital filter
The AD7723 ADC employs a Σ-Δ conversion technique to
convert the analog input into an equivalent digital word. The
modulator samples the input waveform and outputs an
equivalent digital word at the input clock frequency, fCLKIN
.
response can be set to either low-pass or band-pass. The band-
pass response is useful when the input signal is band limited
because the resulting output data rate is half that required to
convert the band when the low-pass operating mode is used. To
illustrate the operation of this mode, consider a band-limited
signal, as shown in Figure 28A. This signal band can be
correctly converted by selecting the (low-pass) ODR = fCLKIN/16
mode, as shown in Figure 28B. Note that the output data rate is a
little over twice the maximum frequency in the frequency band.
Due to the high oversampling rate that spreads the quantization
noise from 0 to fCLKIN/2, the noise energy contained in the band
of interest is reduced (Figure 27A). To further reduce the
quantization noise, a high-order modulator is employed to
shape the noise spectrum so that most of the noise energy is
shifted out of the band of interest (Figure 27B).
The digital filter that follows the modulator removes the large
out-of-band quantization noise (Figure 27C) while also
reducing the data rate from fCLKIN at the input of the filter to
Alternatively, the band-pass mode can be selected, as shown in
Figure 28C. The band-pass filter removes unwanted signals
from dc to just below fCLKIN/64. Rather than outputting data at
fCLKIN/16, the output of the band-pass filter is sampled at
fCLKIN/32. This effectively translates the wanted band to a
maximum frequency of a little less than fCLKIN/64, as shown in
Figure 28D. Halving the output data rate reduces the workload
of any following signal processor and also allows a lower serial
clock rate to be used.
f
CLKIN/32 or fCLKIN/16 at the output of the filter, depending on the
state on the MODE1/MODE2 pins in parallel interface mode or
the SLDR pin in serial interface mode. The AD7723 output data
rate is a little over twice the signal bandwidth, which guarantees
that there is no loss of data in the signal band.
Digital filtering has certain advantages over analog filtering.
First, since digital filtering occurs after the A/D conversion, it
can remove noise injected during the conversion process.
Analog filtering cannot remove noise injected during
conversion. Second, the digital filter combines low pass-band
ripple with a steep roll-off while also maintaining a linear phase
response.
BAND LIMITED SIGNAL
0dB
fCLKIN/16
A
LOW-PASS FILTER RESPONSE
ODR
0dB
SAMPLE
QUANTIZATION NOISE
IMAGE
fCLKIN/2
BAND OF INTEREST
fCLKIN/16
A
LOW-PASS FILTER. OUTPUT DATA RATE = f
/16
CLKIN
B
BAND-PASS FILTER
NOISE SHAPING
RESPONSE
SAMPLE
IMAGE
0dB
fCLKIN/2
BAND OF INTEREST
B
fCLKIN/16
BAND-PASS FILTER
C
DIGITAL FILTER CUTOFF FREQUENCY
FREQUENCY
SAMPLE
TRANSLATED
INPUT SIGNAL
ODR
IMAGE
0dB
fCLKIN/2
BAND OF INTEREST
C
fCLKIN/16
LOW-PASS FILTER. OUTPUT DATA RATE = fCLKIN/32
Figure 27. Sigma-Delta ADC
D
The AD7723 employs four or five finite impulse response (FIR)
filters in series. Each individual filter’s output data rate is half
that of the filter’s input data rate. When data is fed to the
interface from the output of the fourth filter, the output data
rate is fCLKIN/16 and the resulting oversampling ratio (OSR) of
Figure 28. Band-Pass Operation
The frequency response of the three digital filter operating
modes is shown in Figure 29, Figure 30, and Figure 31.
Rev. C | Page 18 of 32
AD7723
Figure 32 shows the frequency response of the digital filter in
both low-pass and band-pass modes. Due to the sampling
nature of the converter, the pass-band response is repeated
about the input sampling frequency, fCLKIN, and at integer
multiples of fCLKIN. Out-of-band noise or signals coincident with
any of the filter images are aliased down to the pass band.
However, due to the AD7723’s high oversampling ratio, these
bands occupy only a small fraction of the spectrum, and most
broadband noise is attenuated by at least 90 dB. In addition, as
shown in Figure 33, with even a low-order filter, there is
significant attenuation at the first image frequency. This
contrasts with a normal Nyquist rate converter where a very
high-order antialias filter is required to allow most of the
bandwidth to be used while ensuring sufficient attenuation at
0dB
–100dB
0
0.5
fCLKIN
1.0
1.0
1.0
multiples of fCLKIN
.
Figure 29. Low-Pass Filter Decimate by 16
0dB
0dB
1
fCLKIN
2fCLKIN
3fCLKIN
Figure 32. Digital Filter Frequency Response
–100dB
OUTPUT
DATA RATE
ANTIALIAS FILTER
RESPONSE
REQUIRED
0dB
ATTENUATION
fCLKIN/32
fCLKIN
Figure 33. Frequency Response of Antialias Filter
0
0.5
fCLKIN
Figure 30. Low-Pass Filter Decimate by 32
0dB
–100dB
0
0.5
fCLKIN
Figure 31. Band-Pass Filter Decimate by 32
Rev. C | Page 19 of 32
AD7723
APPLYING THE AD7723
ANALOG INPUT RANGE
ANALOG INPUT
The AD7723 has differential inputs to provide common-mode
noise rejection. In unipolar mode, the analog input range is 0 to
8/5 × VREF2, while in bipolar mode, the analog input range is
4/5 × VREF2. The output code is twos complement binary in
both modes with 1 LSB = 61 µV. The ideal input/output transfer
characteristics for the two modes are shown in Figure 34. In
both modes, the absolute voltage on each input must remain
within the supply range AGND to AVDD. The bipolar mode
allows either single-ended or complementary input signals.
The analog input of the AD7723 uses a switched capacitor
technique to sample the input signal. For the purpose of driving
the AD7723, an equivalent circuit of the analog inputs is shown
in Figure 36. For each half clock cycle, two highly linear
sampling capacitors are switched to both inputs, converting the
input signal into an equivalent sampled charge. A signal source
driving the analog inputs must be able to source this charge
while also settling to the required accuracy by the end of each
half-clock phase.
011…111
011…110
ΦA
AD7723
500Ω
VIN(+) 20
2pF
ΦB
000…010
000…001
000…000
111…111
111…110
2pF
ΦA
500Ω
VIN(–) 19
AC
GROUND
ΦB
Φ
Φ
Φ
A
Φ
A
CLKIN
B
B
100…001
100…000
Figure 36. Analog Input Equivalent Circuit
–4/5 ×V
REF2
0V
+4/5 × V
REF2
– 1LSB BIPOLAR
(0V)
DRIVING THE ANALOG INPUTS
(+4/5 × V
)
REF2
(+8/5 × V
– 1LSB) UNIPOLAR
REF2
To interface the signal source to the AD7723, at least one op
amp is generally required. Choice of op amp is critical to
achieving the full performance of the AD7723. The op amp not
only has to recover from the transient loads that the ADC
imposes on it, but it must also have good distortion
characteristics and very low input noise. Resistors in the signal
path can also add to the overall thermal noise floor,
necessitating the choice of low value resistors.
Figure 34. Bipolar (Unipolar) Mode Transfer Function
The AD7723 accepts full-scale, in-band signals. However, large
scale out-of-band signals can overload the modulator inputs.
Figure 35 shows the maximum input signal level as a function
of frequency. A minimal single-pole, RC, antialias filter set to
f
CLKIN/24 allows full-scale input signals over the entire frequency
spectrum.
2.2
2.1
2.0
1.9
1.8
1.7
1.6
1.5
Placing an RC filter between the drive source and the ADC
inputs, as shown in Figure 37, has a number of beneficial
effects. Transients on the op amp outputs are significantly
reduced because the external capacitor now supplies the
instantaneous charge required when the sampling capacitors are
switched to the ADC input pins and input circuit noise at the
sample images is now significantly attenuated, resulting in
improved overall SNR. The external resistor serves to isolate the
external capacitor from the ADC output, thus improving op
amp stability while also isolating the op amp output from any
remaining transients on the capacitor. By experimenting with
different filter values, the optimum performance can be
achieved for each application. As a guideline, the RC time
constant (R × C) should be less than a quarter of the clock
period to avoid nonlinear currents from the ADC inputs being
stored on the external capacitor and degrading distortion. This
restriction means that this filter cannot form the main antialias
filter for the ADC.
V
= 2.5V
0.04
REF
1.4
1.3
0
0.02
0.06
0.08
0.10
0.12
0.14
0.5
INPUT SIGNAL FREQUENCY RELATIVE TO fCLKIN
Figure 35. Peak Input Signal Level vs. Signal Frequency
Rev. C | Page 20 of 32
AD7723
R
FB
220Ω
R
R
R
R
390Ω
SOURCE
IN
VIN(+)
VIN(–)
AIN = ±2V
BIASED
ABOUT
AD8047
A1
50Ω
27Ω
20
VIN(+)
C
GROUND
AD7723
220Ω
R
BALANCE1
220Ω
R
BALANCE2
220pF
R
BALANCE2
AD7723
220Ω
Figure 37. Input RC Network
R
27Ω
REF1
10kΩ
19
23
VIN(–)
A2
With the unipolar input mode selected, just one op amp is
required to buffer single-ended input signals. However, driving
the AD7723 with complementary signals and with the bipolar
input range selected has some distinct advantages: even-order
harmonics in both the drive circuits and the AD7723 front end
are attenuated and the peak-to-peak input signal range on both
inputs is halved. Halving the input signal range allows some op
amps to be powered from the same supplies as the AD7723.
Although a complementary driver requires the use of two op
amps per ADC, it may avoid the need to generate additional
supplies just for these op amps.
AD8047
220nF
R
REF2
REF2
20kΩ
10nF
21
REF1
GAIN = 2 × R /(R + R
)
FB
IN
SOURCE
1µF
R
= R
× (R + R
IN
)/(2 × R )
FB
BALANCE1
BALANCE2
SOURCE
× (R + R )/R
IN SOURCE FB
R
= R
REF2
REF1
Figure 39. Single-Ended-to-Differential Input Circuit for Bipolar Mode
Operation (Analog Input Biased About Ground)
APPLYING THE REFERENCE
The reference circuitry used in the AD7723 includes an on-chip
2.5 V band-gap reference and a reference buffer circuit. The
block diagram of the reference circuit is shown in Figure 40.
The internal reference voltage is connected to REF1 through a
3 kΩ resistor and is internally buffered to drive the analog
modulator’s switched cap DAC (REF2). When using the
internal reference, a 1 µF capacitor is required between REF1
and AGND to decouple the band-gap noise. If the internal
reference is required to bias external circuits, use an external
precision op amp to buffer REF1.
Figure 38 and Figure 39 show two such circuits for driving the
AD7723. Figure 38 is intended for use when the input signal is
biased about 2.5 V, while Figure 39 is used when the input signal
is biased about ground. While both circuits convert the input
signal into a complementary signal, the circuit in Figure 39 also
level shifts the signal so that both outputs are biased about 2.5 V.
Suitable op amps include the AD8047, AD8044, AD8041, and
its dual equivalent, the AD8042. The AD8047 has lower input
noise than the AD8041/AD8042 but has to be supplied from a
+7.5 V/−2.5 V supply. The AD8041/AD8042 typically degrades
SNR from 90 dB to 88 dB but can be powered from the same
single 5 V supply as the AD7723.
COMPARATOR
1V
AD7723
REFERENCE
BUFFER
REF1
SWITCHED-CAP
21
DAC REFERENCED
1µF
3kΩ
R
220Ω
FB
2.5V
REFERENCE
R
R
390Ω
SOURCE
IN
AIN = ±2V
BIASED
ABOUT 2.5V
23
REF2
AD8047
A1
50Ω
27Ω
20
VIN(+)
Figure 40. Reference Circuit Block Diagram
220Ω
Where gain error or gain error drift requires the use of an
external reference, the reference buffer in Figure 40 can be
turned off by grounding the REF1 pin and the external
reference can be applied directly to REF2 pin. The AD7723
accepts an external reference voltage between 1.2 V to 3.15 V.
By applying a 3 V rather than a 2.5 V reference, SNR is typically
improved by about 1 dB. Where the output common-mode
range of the amplifier driving the inputs is restricted, the full-
scale input signal span can be reduced by applying a lower than
2.5 V reference. For example, a 1.25 V reference would make
the bipolar input span 1 V but would degrade SNR.
220pF
AD7723
220Ω
27Ω
19
23
VIN(–)
REF2
A2
10kΩ
AD8047
220nF
10nF
21
REF1
1µF
GAIN = 2 × R /(R
+ R )
IN
FB
SOURCE
Figure 38. Single-Ended-to-Differential Input Circuit for Bipolar Mode
Operation (Analog Input Biased About 2.5 V)
Rev. C | Page 21 of 32
AD7723
In all cases, since the REF2 voltage connects to the analog
modulator, a 220 nF and 10 nF capacitor must connect directly
from REF2 to AGND. The external capacitor provides the
charge required for the dynamic load presented at the REF2 pin
(see Figure 41).
AD7723
XTAL CLKIN
1MΩ
Φ
A
Figure 43. Crystal Oscillator Connection
Φ
4pF
B
When an external clock source is being used, the internal
oscillator circuit can be disabled by tying XTAL_OFF high. A
low phase noise clock should be used to generate the ADC
sampling clock because sampling clock jitter effectively
modulates the input signal and raises the noise floor. The
sampling clock generator should be isolated from noisy digital
circuits, grounded, and heavily decoupled to the analog ground
plane.
REF2
23
10nF
220nF
Φ
4pF
Φ
A
B
SWITCHED-CAP
DAC REFERENCED
ꢀ
Φ
Φ
Φ
Φ
B
CLKIN
A
A
B
Figure 41. REF2 Equivalent Input Circuit
The AD780 is ideal to use as an external reference with the
AD7723. Figure 42 shows a suggested connection diagram.
Grounding Pin 8 on the AD780 selects the 3 V output mode.
The sampling clock generator should be referenced to the
analog ground in a split ground system. However, this is not
always possible because of system constraints. In many
applications, the sampling clock must be derived from a higher
frequency multipurpose system clock that is generated on the
digital ground plane. If the clock signal is passed between its
origin on a digital ground plane to the AD7723 on the analog
ground plane, the ground noise between the two planes adds
directly to the clock and produces excess jitter. The jitter can
cause degradation in the signal-to-noise ratio and also produce
unwanted harmonics. This can be remedied somewhat by
transmitting the sampling signal as a differential one, using
either a small RF transformer or a high speed differential driver
and a receiver such as PECL. In either case, the original master
system clock should be generated from a low phase noise crystal
oscillator.
2.5V
5V
O/P
SELECT
REF2
NC
+V
1
2
3
4
8
7
6
5
IN
NC
220nF
AD7723
10nF
1µF
V
TEMP
GND
OUT
22nF
22µF
TRIM
REF1
AD780
NC = NO CONNECT
Figure 42. External Reference Circuit Connection
CLOCK GENERATION
The AD7723 contains an oscillator circuit to allow a crystal or
an external clock signal to generate the master clock for the
ADC. The connection diagram for use with a crystal is shown
in Figure 43. Consult the manufacturer’s recommendation for
the load capacitors. To enable the oscillator circuit on board the
AD7723, XTAL_OFF should be tied low.
Rev. C | Page 22 of 32
AD7723
SYSTEM SYNCHRONIZATION
The SYNC input provides a synchronization function for use in
parallel or serial mode. SYNC allows the user to begin gathering
samples of the analog input from a known point in time.
Following a SYNC, the modulator and filter need time to settle
before data can be read from the AD7723.
goes high
DRDY
following a synchronization and it remains high until valid data
is available at the interface.
This allows a system using multiple AD7723s, operated from a
common master clock, to be synchronized so that each ADC
simultaneously updates its output register.
When operating in any of the serial modes, either SYNC or
frame sync input (FSI) may be used to synchronize multiple
AD7723 devices to a common master clock. The functionality
of FSI is detailed in the Serial Interface section.
In a system using multiple AD7723s, a common signal to their
sync inputs synchronizes their operation. On the rising edge of
SYNC, the digital filter sequencer is reset to 0. The filter is held
in a reset state until a rising edge on CLKIN senses SYNC low.
A SYNC pulse, one CLKIN cycle long, can be applied
synchronous to the falling edge of CLKIN. This way, on the
next rising edge of CLKIN, SYNC is sensed low, the filter is
taken out of its reset state, and multiple parts begin to gather
input samples.
Rev. C | Page 23 of 32
AD7723
DATA INTERFACING
cycles, the rising edge of
is used to latch the conversion
DRDY
data before a new conversion result is loaded into the output
data register. The falling edge of then sends an
The AD7723 offers a choice of serial or parallel data interface
options to meet the requirements of a variety of system
configurations. In parallel mode, multiple AD7723s can easily
be configured to share a common data bus. Serial mode is ideal
when it is required to minimize the number of data interface
lines connected to a host processor. In either case, careful
attention to the system configuration is required to realize the
high dynamic range available with the AD7723. Consult the
recommendations in the Grounding and Layout section. The
following recommendations for parallel interfacing also apply
for the system design when using the serial mode.
DRDY
appropriate interrupt signal for interface control. Alternatively,
if buffers are used instead of latches, the falling edge of
provides the necessary interrupt when a new output word is
available from the AD7723.
DRDY
AD7723
DSP
16
74XX16374
16
D15
DB15
ADDR
DECODE
ADDR
PARALLEL INTERFACE
DRDY
When using the AD7723, place a buffer/latch adjacent to the
converter to isolate the converter’s data lines from any noise
that may be on the data bus. Even though the AD7723 has three
state outputs, use of an isolation latch represents good design
practice.
OE
RD
CS
RD
INTERRUPT
Figure 44. Parallel Interface Connection
Figure 44 shows how the parallel interface of the AD7723 can
be configured to interface with the system data bus of a
microprocessor or a microcontroller, such as the MC68HC16 or
8XC251. With
and
tied permanently low, the data output
CS
RD
bits are always active. When
goes high for two clock
DRDY
Rev. C | Page 24 of 32
AD7723
SERIAL INTERFACE
The AD7723’s serial data interface can operate in three modes,
depending on the application requirements. The timing
diagrams in Figure 4, Figure 5, and Figure 6 show how the
AD7723 may be used to transmit its conversion results. Table 3
shows the control inputs required to select each serial mode and
the digital filter operating mode. The AD7723 operates solely in
the master mode, providing three serial data output pins for
transfer of the conversion results. The serial data clock output,
SCO, serial data output, SDO, and frame sync output, FSO, are
all synchronous with CLKIN. FSO is continuously output at the
conversion rate of the ADC.
In Serial Mode 1, the control input, SFMT, can be used to select
the format for the serial data transmission (see Figure 4). FSO is
either a pulse, approximately one SCO cycle in duration, or a
square wave with a period of 32 SCO cycles. With a logic low
level on SFMT, FSO pulses high for one SCO cycle at the
beginning of a data transmission frame. With a logic high level
on SFMT, FSO goes low at the beginning of a data transmission
frame and returns high after 16 SCO cycles.
Note that in Serial Mode 1, FSI can be used to synchronize the
AD7723 if SFMT is set to a logic high. If SFMT is set low, the
FSI input has no effect on synchronization.
Serial data shifts out of the SDO pin synchronous with SCO.
The FSO is used to frame the output data transmission to an
external device. An output data transmission is either 16 or 32
SCO cycles in duration (see Table 3). Serial data shifts out of the
SDO pin, MSB first, LSB last, for a duration of 16 SCO cycles. In
Serial Mode 1, SDO outputs 0s for the last 16 SCO cycles of the
32-cycle data transmission frame.
In Serial Mode 2 and Serial Mode 3, SFMT should be tied high.
TSI and DOE should be tied low in these modes. The FSO is a
pulse, approximately one SCO cycle in duration, occurring at
the beginning of the serial data transmission.
TWO-CHANNEL MULTIPLEXED OPERATION
Two additional serial interface control pins, DOE and TSI, are
provided to allow the serial data outputs of two AD7723s, to
easily share one serial data line when operating in Serial
Mode 1. Figure 45 shows the connection diagram. Since a serial
data transmission frame lasts 32 SCO cycles, two ADCs can
share a single data line by alternating transmission of their 16-
bit output data onto one SDO pin.
The clock format pin, CFMT, selects the active edge of SCO.
With CFMT tied logic low, the serial interface outputs FSO and
SDO change state on the SCO rising edge and are valid on the
falling edge of SCO. With CFMT set high, FSO and SDO
change state on the falling SCO edge and are valid on the SCO
rising edge.
AD7723
DV
DD
The frame sync input, FSI, can be used if the AD7723
conversion process must be synchronized to an external source.
FSI allows the conversion data presented to the serial interface
to be a filtered and decimated result derived from a known
point in time. A common frame sync signal can be applied to
two or more AD7723s to synchronize them to a common
master clock.
MASTER
SFMT
CFMT
TSI
SDO
SCO
FSO
TO HOST
PROCESSOR
DGND
FSI
DOE
CLKIN
FROM
CONTROL
LOGIC
AD7723
When FSI is applied for the first time, the digital filter
sequencer counter is reset to 0, the AD7723 interrupts the
current data transmission, reloads the output shift register,
resets SCO, and transmits the conversion result. Synchro-
nization starts immediately and the following conversions are
invalid while the digital filter settles. FSI can be applied once
after power-up, or it can be a periodic signal, synchronous to
CLKIN, occurring every 32 CLKIN cycles. Subsequent FSI
inputs applied every 32 CLKIN cycles do not alter the serial
data transmission and do not reset the digital filter sequencer
counter. FSI is an optional signal; if synchronization is not
required, FSI can be tied to a logic low and the AD7723
generates FSO outputs.
SLAVE
DOE
SDO
SCO
FSO
FSI
DV
DD
CLKIN
SFMT
TSI
CFMT
DGND
Figure 45. Serial Mode 1 Connection for Two-Channel Multiplexed Operation
The data output enable pin, DOE, controls the SDO output
buffer. When the logic level on DOE matches the state of the
TSI pin, the SDO output buffer drives the serial data line;
otherwise, the output of the buffer goes high impedance. The
serial format pin, SFMT, is set high to choose the frame sync
output format. The clock format pin, CFMT, is set low so that
serial data is made available on SDO after the rising edge of
SCO and can be latched on the SCO falling edge.
Rev. C | Page 25 of 32
AD7723
The master device is selected by setting TSI to a logic low and
connecting its FSO to DOE. The slave device is selected with its
TSI pin tied high and both its FSI and DOE controlled from the
master’s FSO. Since the FSO of the master controls the DOE
input of both the master and slave, one ADC’s SDO is active
while the other is high impedance (Figure 46). When the master
transmits its conversion result during the first 16 SCO cycles of
a data transmission frame, the low level on DOE sets the slave’s
SDO high impedance. Once the master completes transmitting
its conversion data, its FSO goes high and triggers the slave’s FSI
to begin its data transmission frame.
Since FSO pulses are gated by the release of FSI (going low) and
the FSI of the slave device is held high during its data
transmission, the FSO from the master device must be used for
connection to the host processor.
CLKIN
FSI
t9
SCO
t11
t12
FSO (MASTER)
FSI (SLAVE)
t13
DOE (MASTER AND SLAVE)
t16
t15
SDO (MASTER)
SDO (SLAVE)
D15
t16
D14
D1
D0
t15
D1
D0
D15
D14
Figure 46. Serial Mode 1 Timing for Two-Channel Multiplexed Operation
Rev. C | Page 26 of 32
AD7723
SERIAL INTERFACE TO DSPs
(the DSP begins reading the 16-bit word after the DSP has
In serial mode, the AD7723 can be directly interfaced to several
industry-standard digital signal processors. In all cases, the
AD7723 operates as the master with the DSP operating as the
slave. The AD7723 provides its own serial clock (SCO) to
transmit the digital word on the SDO pin to the DSP. The
AD7723 also generates the frame synchronization signal that
synchronizes the transfer of the 16-bit word from the AD7723
to the DSP. Depending on the serial mode used, SCO has a
frequency equal to CLKIN or equal to CLKIN/2. When SCO
equals 19.2 MHz, the AD7723 can be interfaced to the Analog
Devices ADSP-2106x SHARC DSP. With a 19.2 MHz master
clock and SCO equal to CLKIN/2, the AD7723 can be
interfaced with the ADSP-21xx family of DSPs, the DSP56002,
and the TMS320C5x-57. When the AD7723 is used in the
HALF_PWR Mode, that is, CLKIN is less than 10 MHz, then
the AD7723 can be used with DSPs, such as the
identified the frame sync signal rather than the DSP reading the
word at the same instant as the frame sync signal is identified),
and LRFS = 0 (RFS is active high). The AD7723 can be used in
Mode 1, Mode 2, or Mode 3 when interfaced to the ADSP-
2106x SHARC DSP.
AD7723 TO DSP56002 INTERFACE
Figure 48 shows the AD7723 to DSP56002 interface. To
interface the AD7723 to the DSP56002, the ADC is operated in
Mode 2 when the ADC is operated with a 19.2 MHz clock. The
DSP56002 is configured as follows: SYN = 1 (synchronous
mode), SCD1 = 0 (RFS is an input), GCK = 0 (a continuous
serial clock is used), SCKD = 0 (the serial clock is external),
WL1 = l, WL0 = 0 (transfers is 16 bits wide), FSL1 = 0, and
FSL0 = 1 (the frame sync is active at the beginning of each
transfer). Alternatively, the DSP56002 can be operated in
asynchronous mode (SYN = 0).
TMS320C20/TMS320C25 and the DSP56000/DSP56001.
AD7723 TO ADSP-21xx INTERFACE
In this mode, the serial clock for the receive section is input to
the SCO pin. This is accomplished by setting Bit SCDO to 0
(external Rx clock).
Figure 47 shows the interface between the ADSP-21xx and the
AD7723. The AD7723 is operated in Mode 2 so that SCO =
CLKIN/2. For the ADSP-21xx, the bits in the serial port control
register should be set up as RFSR = 1 (a frame sync is needed
for each transfer), SLEN = 15 (16-bit word lengths), RFSW = 0
(normal framing mode for receive operations), INVRFS = 0
(active high RFS), IRFS = 0 (external RFS), and ISCLK = 0
(external serial clock).
DSP56002
AD7723
SDR
SC1
SCK
SDO
FSO
SCO
Figure 48. AD7723 to DSP56002 Interface
ADSP-21xx
AD7723
DR
RFS
SDO
FSO
SCO
AD7723 TO TMS320C5x INTERFACE
Figure 49 shows the AD7723 to TMS320C5x interface. For the
TMS320C5x, FSR and CLKR are automatically configured as
inputs. The serial port is configured as follows: FO = 0 (16-bit
word transfers) and FSM = 1 (a frame sync occurs for each
transfer).
SCLK
Figure 47. AD7723 to ADSP-21xx Interface
AD7723 TO SHARC INTERFACE
TMS320C5x
The interface between the AD7723 and the ADSP-2106x
SHARC DSP is the same as shown in Figure 47, but the DSP is
configured as follows: SLEN = 15 (16-bit word transfers),
SENDN = 0 (the MSB of the 16-bit word is received by the DSP
first), ICLK = 0 (an external serial clock is used), RFSR = 0 (a
frame sync is required for every word transfer), IRFS = 0 (the
receive frame sync signal is external), CKRE = 0 (the receive
data is latched into the DSP on the falling clock edge), LAFS = 0
AD7723
DR
FSR
SDO
FSO
SCO
CLKR
Figure 49. AD7723 to TMS320C5x Interface
Rev. C | Page 27 of 32
AD7723
GROUNDING AND LAYOUT
The analog and digital power supplies to the AD7723 are
independent and separately pinned out to minimize coupling
between the analog and digital sections within the device. The
AD7723 AGND and DGND pins should be soldered directly to
a ground plane to minimize series inductance. In addition, the
ac path from any supply pin or reference pin (REF1 and REF2)
through its decoupling capacitors to its associated ground must
be made as short as possible (Figure 50). To achieve the best
decoupling, place surface-mount capacitors as close as possible
to the device, ideally right up against the device pins.
Avoid running digital lines under the device as these couple
noise onto the die. The analog ground plane should be allowed
to run under the AD7723 to shield it from noise coupling. The
power supply lines to the AD7723 should use as large a trace as
possible (preferably a plane) to provide a low impedance path
and reduce the effects of glitches on the power supply line.
Avoid crossover of digital and analog signals. Traces on
opposite sides of the board should run at right angles to each
other. This reduces the effects of feedthrough through the
board.
All ground planes must not overlap to avoid capacitive
coupling. The AD7723’s digital and analog ground planes must
be connected at one place by a low inductance path, preferably
right under the device. Typically, this connection is either a
trace on the printed circuit board of 0.5 cm wide when the
ground planes are on the same layer, or 0.5 cm wide minimum
plated through holes when the ground planes are on different
layers. Any external logic connected to the AD7723 should use
a ground plane separate from the AD7723’s digital ground
plane. These two digital ground planes should also be
connected at just one place.
23
22
REF2
10nF
220nF
AGND2
REF1
1µ F
21
11
AV
1
DD
10nF
10
9
AGND1
AGND1
5V
17
18
26
25
AV
DD
10nF
10µ F
100nF
100nF
AGND
AV
DD
10nF
10nF
Separate power supplies for AVDD and DVDD are also highly
desirable. The digital supply pin DVDD should be powered from
a separate analog supply, but if necessary, DVDD may share its
power connection to AVDD, as shown in the connection diagram
in Figure 50. The ferrites are also recommended to filter high
frequency signals from corrupting the analog power supply.
AGND
AD7723 ANALOG
GROUND PLANE
AD7723 DIGITAL
GROUND PLANE
39
DV
DD
10µ F
100nF
10nF
6
DGND
DGND
28
A minimum etch technique is generally best for ground planes
because it gives the best shielding. Noise can be minimized by
paying attention to the system layout and preventing different
signals from interfering with each other. High level analog
signals should be separated from low level analog signals, and
both should be kept away from digital signals. In waveform
sampling and reconstruction systems, the sampling clock
(CLKIN) is as vulnerable to noise as any analog signal. CLKIN
should be isolated from the analog and digital systems. Fast
switching signals like clocks should be shielded with their
associated ground to avoid radiating noise to other sections of
the board, and clock signals should never be routed near the
analog inputs.
Figure 50. Reference and Power Supply Decoupling
Rev. C | Page 28 of 32
AD7723
OUTLINE DIMENSIONS
1.03
0.88
0.73
2.45
MAX
13.90
BSC SQ
33
23
34
22
SEATING
PLANE
10.00
BSC SQ
TOP VIEW
(PINS DOWN)
10°
6°
2°
2.10
2.00
1.95
0.23
0.11
VIEW A
PIN 1
44
12
7°
0°
1
11
0.25 MIN
0.10
COPLANARITY
0.45
0.30
0.80 BSC
LEAD PITCH
VIEW A
LEAD WIDTH
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MO-112-AA-1
Figure 51. 44-Lead Metric Quad Flat Package [MQFP]
(S-44-2)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD7723BS
AD7723BS-REEL
AD7723BSZ1
AD7723BSZ-REEL1
Temperature Package
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
Package Description
Package Outline
44-Lead Metric Quad Flat Package (MQFP)
44-Lead Metric Quad Flat Package (MQFP)
44-Lead Metric Quad Flat Package (MQFP)
44-Lead Metric Quad Flat Package (MQFP)
Evaluation Board
S-44-2
S-44-2
S-44-2
S-44-2
EVAL-AD7723CB
1 Z = Pb-free part.
Rev. C | Page 29 of 32
AD7723
NOTES
Rev. C | Page 30 of 32
AD7723
NOTES
Rev. C | Page 31 of 32
AD7723
NOTES
©2005 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C01186–0–5/05(C)
Rev. C | Page 32 of 32
相关型号:
©2020 ICPDF网 联系我们和版权申明