HMC677LP5RTR [ADI]
HMC677LP5RTR;
| 型号： | HMC677LP5RTR |
| 厂家： | 
ADI |
| 描述： | HMC677LP5RTR 信息通信管理 接口集成电路 |
| 文件： | 总8页 (文件大小：212K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
HMC677LP5 / 677LP5E
v02.0309
6-Bit SERIAL/PARALLEL SWITCH
DRIVER/CONTROLLER
Typical Applications
Features
The HMC677LP5(E) is ideal for:
Accepts Serial or Parallel Data
Compatible with TTL and CMOS Logic
Complementary Outputs
6-Bit Control Word
• Microwave and Millimeterwave Control Circuits
• Test and Measurement Equipment
• Complex Multi-Function Assemblies
• Military and Space Subsystems
Power-up State Selection
Low Power Consumption
Fast Clock Rate
8
• Transmit/Receive Module Controllers
Functional Diagram
General Description
The HMC677LP5(E) is a multi-function BiCMOS
control interface IC which is ideal for driving the
gates of FET and pHEMT based MMIC control
devices. This unique IC can be used to simplify the
control of microwave and millimeterwave transmit/
receive modules, military subsystems, and multithrow/
multiport test and measurement equipment. The
HMC677LP5(E) accepts serial or parallel data, and
can drive up to 6 complementary sets of outputs.
The HMC677LP5(E) also provides additional
functionality such as a power-up state selection,
adjustable output voltage levels, and a latched paral-
lel control mode which allows multiple control devices
to share a common data bus. The HMC677LP5(E)
is ideal for controlling digital phase shifters, digital
attenuators, digital variable gain amplifiers, and
switching matrices embedded in complex microwave
and millimeterwave assemblies.
Electrical Specifications, TA = +25° C, Vdd1 = Vdd2 = +5V, Vee = -5V, Voph = 0V
Parameter
Min
Typ
Max
Units
V
Input High Voltage, Vih
2
-
-
-
-
-
-
-
-
-
Low Voltage, Vil
-
0.8
V
Output High Voltage, Voh (Ioh = 1 mA, Vee = -4.5V)
Output Low Votlage, Vol (Iol = 2 mA, Vee = -4.5V)
Maximum Input Leakage Current, Iin
Propagation Delay, tplh
Voph - 0.1
-
V
-
-
-
-
-
Vee + 0.1
V
1
μA
nS
Mbps
ns
80
Maximum Serial Bit Rate
10
Maximum I/O Update Rate
100
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
8 - 2
HMC677LP5 / 677LP5E
v02.0309
6-Bit SERIAL/PARALLEL SWITCH
DRIVER/CONTROLLER
Operating Ranges
Function
Parameter
Min.
4.5
-5.5
0
Typ.
5.0
-5.0
-
Max
5.5
-4.5
2.2
7.7
11
Units
V
Vdd
Vee
Positive DC Supply Voltage
Negative DC Supply Voltage
DC Output Supply
V
Voph [1]
Voph - Vee
Vdd - Vee
Ta
V
Negative Supply Voltage Range
Positive to Negative Supply Range
Operating Ambient Temperature
DC Output Current - High
4.5
9
-
V
10
25
-
V
-40
1
85
-
C
8
loh [2]
mA
mA
lol [2]
DC Output Current - Low
2
-
-
[1] Voph can be used from 0V to 2.2V. Higher voltages can be used to increase low frequency performance of GaAs switches.
[2] Ioh and Iol are measured at 0.1V variation from Voph and Vee.
DC Characteristics
Function
Parameter
Conditions
Min.
Typ.
Max
Units
V
Vih
Input High Voltage
High Input Voltage
Low Input Voltage
2.0
-
-
-
-
-
-
-
Vil
Input Low Voltage
-
0.8
V
Voh
Vol
Output High Voltage
Output Low Voltage
Input Leakage Current
Quiescent Supply Current
Ioh = 1 mA
Vee = -4.5V
Vee = -4.5V
Voph - 0.1
-
Vee +0.1
1
V
Iol = 2 mA
Vin = Vdd or GND
Vdd = Max
-
-
-
V
lin
Vdd = Max
μA
mA
Idd
Vin = Vdd or GND
1.5
Additional Supply
Current Per TTL Input Pin
^ Idd
Vdd = Max
Vin = 2V
-
-
50
μA
Worst Case AC Characteristics at Voph = 2.2V (Vdd = 4.5V, Vee = -4.5V)
Function
Parameter
-40 °C
+25 °C
+85 °C
Units
Tplh
Rising Propagation Delay
30
30
30
ns
ns
ns
ns
nS
pF
pF
Tphl
Falling Propagation Delay
30
30
30
Ttlh
Output Rising Transition Time
Output Falling Transition Time
Delay Skew
30
40
40
Tthl
15
20
20
Tskew
Cpdd[1]
Cpde[1]
50
50
50
Power Dissipation Capacitance of Vdd
Power Dissipation Capacitance of Vee
100
400
100
400
100
400
Worst Case AC Characteristics at Voph = 0V (Vdd = 4.5V, Vee = -4.5V)
Function
Parameter
-40 °C
+25 °C
+85 °C
Units
ns
Tplh
Rising Propagation Delay
80
80
80
Tphl
Falling Propagation Delay
80
80
80
ns
Ttlh
Output Rising Transition Time
Output Falling Transition Time
Delay Skew
100
50
100
50
100
50
ns
Tthl
ns
Tskew
Cpdd[1]
Cpde[1]
50
50
50
nS
pF
pF
Power Dissipation Capacitance of Vdd
Power Dissipation Capacitance of Vee
100
400
100
400
100
400
1] Total Power Dissipation is calculated by the following formula: PD = Vdd2 f Cpdd + (Voph - Vee)2 f Cpde, where f = frequency in Hz
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
8 - 3
HMC677LP5 / 677LP5E
v02.0309
6-Bit SERIAL/PARALLEL SWITCH
DRIVER/CONTROLLER
Serial Control Interface
The HMC677LP5(E) contains a 3-wire SPI compatible digital interface (DATA, CLK, LE). It is activated when P/S
is kept high. The 6-bit serial word must be loaded MSB first. The positive-edge sensitive CLK and LE requires
clean transitions. Standard logic families work well. When LE is high, 6-bit data in the serial input register is transferred
to the outputs. When LE is high CLK is masked to prevent data transition during output loading.
When P/S is low, 3-wire SPI interface inputs (DATA, CLK, LE) are disabled and the serial input register is loaded
asynchronously with parallel digital inputs (I0-I5). When LE is high, 6-bit parallel data is transferred.
8
For all modes of operations, the outputs will stay constant while LE is kept low.
Parameter
Typ.
Timing Diagram (Latched Parallel Mode)
Min. serial period, tSCK
Control set-up time, tCS
Control hold-time, tCH
LE setup-time, tLN
100 ns
20 ns
20 ns
10 ns
10 ns
530 ns
Min. LE pulse width, tLEW
Min LE pulse spacing, tLES
Serial clock hold-time from LE, tCKN 10 ns
Parallel Mode
(Direct Parallel Mode & Latched Parallel Mode)
Note: The parallel mode is enabled when P/S is set to low.
Direct Parallel Mode - Outputs are changed by the Control Voltage Inputs directly. The LE (Latch Enable) must be at
a logic high to control in this manner.
Latched Parallel Mode - Outputs are selected using the Control Voltage Inputs and set while the LE is in the Low
state. This will not change state while LE is Low. Once all Control Voltage Inputs are at the desired states the LE is
pulsed. See timing diagram above for reference.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
8 - 4
HMC677LP5 / 677LP5E
v02.0309
6-Bit SERIAL/PARALLEL SWITCH
DRIVER/CONTROLLER
Power-On Sequence
Power-Up States
The Power-up (PUP) states work in both serial and
parallel modes, provided that LE is held low. The
circuit latches in the state of the I5-I0 pins 200 ms after
power-up. The state of I5-I0 pins should be held firmly
high or low for at least 250 ms following power-up. The
PUP state is locked out after the first LE pulse, until
Vdd drops below 4.5V.
The ideal power-up sequence is: GND, Vdd, Vee,
Voph, digital inputs. The relative order of the digital
inputs are not important as long as they are powered
after Vdd / Vee / Voph / GND.
8
Absolute Maximum Ratings
Truth Table
Digital Inputs
Input
Outputs
(I0-I5, Shift Clock, Latch Enable,
P/S, PUP and Data Inputs)
-1.5V to (Vdd +1.5V) V
Ix
Bx
BxB
Voph
Vee
Low
High
Vee
Bias Voltage (Vdd)
Bias Voltage (Vee)
Bias Voltage (Voph)
Channel Temperature
5.6 V
Voph
-5.6 V
2.3 V
125 °C
Continuous Pdiss (T = 85 °C)
325 mW
(derate 8.2 mW/°C above 85 °C) [1]
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Thermal Resistance
(Channel to ground paddle)
123 °C/W
Storage Temperature
Operating Temperature
-65 to +150 °C
-40 to +85 °C
PUP Truth Table
Output States
B3 B2
LE
PUP2
PUP1
B5
0
B4
0
B1
0
B0
0
0
0
0
0
1
0
0
1
1
X
0
1
0
1
X
0
0
0
1
0
0
1
0
0
1
0
0
1
0
0
0
1
1
1
1
Set by the inputs
For the Inputs (LE, PUP1, PUP2), Logic “0” = 0V and Logic “1” = Vdd
For the outputs, Logic “0” is Bx = Vee, BxB = Voph, and Logic “1” is Bx = Voph, BxB = Vee
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
8 - 5
HMC677LP5 / 677LP5E
v02.0309
6-Bit SERIAL/PARALLEL SWITCH
DRIVER/CONTROLLER
Outline Drawing
8
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS].
3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE.
4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE.
5. ALL GROUND LEADS MUST BE SOLDERED TO PCB GROUND.
6. CLASSIFIED AS MOISTURE SENSITIVITY LEVEL (MSL) 1.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
MSL1 [1]
Package Marking [3]
H677
XXXX
HMC677LP5
Low Stress Injection Molded Plastic
Sn/Pb Solder
H677
XXXX
MSL1 [2]
HMC677LP5E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
8 - 6
HMC677LP5 / 677LP5E
v02.0309
6-Bit SERIAL/PARALLEL SWITCH
DRIVER/CONTROLLER
Pin Descriptions
Pin Number
Function
Description
Supply Voltage
Interface Schematic
1, 29
2 - 7
9
Vdd1, Vdd2
I0 - I5
P/S
10
CLK
See Truth Table, Control Voltage Table
and Timing Diagram
11
SERIN
LE
8
12
31, 32
PUP2, PUP1
No connection necessary. These pins may
be connected to DC ground.
8, 13, 14
N/C
15, 17, 19,
21, 23, 25
B0 - B5
Complementary Outputs
16, 18, 20,
22, 24, 26
B0B - B5B
Vee
27
28
Negative Supply.
VOPH
User selectable output high voltage 0 to +2.2V
30
SEROUT
Serial input data delayed by six clock cycles.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
8 - 7
HMC677LP5 / 677LP5E
v02.0309
6-Bit SERIAL/PARALLEL SWITCH
DRIVER/CONTROLLER
Application & Evaluation PCB Schematic
8
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
8 - 8
HMC677LP5 / 677LP5E
v02.0309
6-Bit SERIAL/PARALLEL SWITCH
DRIVER/CONTROLLER
Evaluation PCB
8
List of Materials for Evaluation PCB 119681 [1][3]
The evaluation circuit board shown is available from
Item
Description
Hittite upon request.
C1, C3, C5
C2, C4, C6
J1 - J4
1000 pF Capacitor, 0402 Pkg.
0.1 μF Capacitor, 0402 Pkg.
Multi Pin DC Connector
R1 - R12
U1
39kΩ Resistor, 0402 Pkg.
HMC677LP5(E) 6-Bit Digital Level Shifter
119679 Evaluation PCB
[2]
PCB
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: FR4
[3] Please refer to part’s pin description and functional diagram for
pin out assignments on evaluation board.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
8 - 9
相关型号：
HMC679LC3CTR
T Flip-Flop, 679 Series, 1-Func, Positive Edge Triggered, 1-Bit, Complementary Output, CQCC16, 3 X 3 MM, ROHS COMPLIANT, CERAMIC, SMT-16
HITTITE
©2020 ICPDF网 联系我们和版权申明