LT1118CS8-2.5#TR [ADI]
Fixed Positive LDO Regulator, 2.5V, 1.3V Dropout, PDSO8;型号: | LT1118CS8-2.5#TR |
厂家: | ADI |
描述: | Fixed Positive LDO Regulator, 2.5V, 1.3V Dropout, PDSO8 光电二极管 输出元件 调节器 |
文件: | 总8页 (文件大小:246K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LT1118/LT1118-2.5
LT1118-2.85/LT1118-5
Low I , Low Dropout,
Q
800mA, Source and Sink
Regulators Adjustable and
Fixed 2.5V, 2.85V, 5V Output
DESCRIPTION
FEATURES
The LT®1118 family of low dropout regulators has the
unique capability of maintaining output regulation while
sourcingorsinkingloadcurrent. The2.85Voutputvoltage
regulator is ideal for use as a Boulay termination of up
to 27 SCSI data lines. The regulator maintains regulation
while both sourcing and sinking current, enabling the use
of active negation drivers for improved noise immunity on
the data lines. Regulation of output voltage is maintained
for TERMPWR voltages as low as 4.0V. When unloaded,
quiescentsupplycurrentisalow600μA,allowingcontinu-
ous connection to the TERMPWR lines. An ultralow power
shutdown mode is also available on the SO-8 version. In
Shutdown the output is high impedance and supply cur-
rent drops to less than 10μA.
n
Regulates While Sourcing or Sinking Current
n
Provides Termination for up to 27 SCSI Lines
n
600μA Quiescent Current
Ultralow Power Shutdown Mode
n
n
Current Limit and Thermal Shutdown Protection
n
Stable for Any C
≥ 0.22μF
LOAD
n
n
Fast Settling Time
1V Dropout Voltage
APPLICATIONS
n
Active Negation SCSI Terminations
n
n
n
n
Computers
Disk Drives
CD-ROM
Supply Splitter
Current limits in both sourcing and sinking modes, plus
on-chip thermal shutdown make the circuit tolerant of
output fault conditions.
L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation.
All other trademarks are the property of their respective owners.
The LT1118 is available in 3-lead SOT-223 and 8-lead SO
packages.
TYPICAL APPLICATION
Load Transient Response
0.2V
LT1118-2.85 OUT
GND
IN
0V
$V
OUT
–0.2V
1μF
CERAMIC
5V
2.2μF
800mA
I
LOAD
I
LOAD
1118 TA01
0mA
–400mA
1118 TA02
1118fd
1
LT1118/LT1118-2.5/
LT1118-2.85/LT1118-5
(Note 1)
ABSOLUTE MAXIMUM RATINGS
Supply Voltage (V ) ................................................15V
Operating Temperature Range...................... 0°C to 70°C
Storage Temperature Range...................–65°C to 150°C
Lead Temperature (Soldering, 10 sec) .................. 300°C
CC
Input Voltage (Enable).................................–0.2V to 7V
Output Voltage ............................... –0.2V to V + 0.5V
CC
Short-Circuit Duration ..................................... Indefinite
PIN CONFIGURATION
TOP VIEW
TOP VIEW
FRONT VIEW
3
2
1
IN
IN
OUT
GND
IN
1
2
3
4
8
7
6
5
EN
GND
NC
EN
1
2
3
4
8
7
6
5
GND
IN
GND
GND
NC
TAB IS
GND
GND
OUT
OUT
IN
FB
S8 PACKAGE
8-LEAD PLASTIC SO
S8 PACKAGE
8-LEAD PLASTIC SO
ST PACKAGE
3-LEAD PLASTIC SOT-223
T
= 125°C, θ = 15°C/W
T
= 125°C, θ = 15°C/W
JA
T
= 125°C, θ = 15°C/W
JMAX
JC
JMAX
JMAX
JA
ORDER INFORMATION
LEAD FREE FINISH
LT1118CS8#PBF
LT1118CS8-2.5#PBF
LT1118CS8-2.85#PBF
LT1118CS8-5#PBF
LT1118CST-2.5#PBF
LT1118CST-2.85#PBF
LT1118CST-5#PBF
LEAD BASED FINISH
LT1118CS8
TAPE AND REEL
PART MARKING
1118
PACKAGE DESCRIPTION
8-Lead Plastic SO
TEMPERATURE RANGE
0°C to 70°C
LT1118CS8#TRPBF
LT1118CS8-2.5#TRPBF
111825
8-Lead Plastic SO
0°C to 70°C
LT1118CS8-2.85#TRPBF 111828
8-Lead Plastic SO
0°C to 70°C
LT1118CS8-5#TRPBF
LT1118CST-2.5#TRPBF
11185
8-Lead Plastic SO
0°C to 70°C
111825
3-Lead Plastic SOT-223
3-Lead Plastic SOT-223
3-Lead Plastic SOT-223
PACKAGE DESCRIPTION
8-Lead Plastic SO
0°C to 70°C
LT1118CST-2.85#TRPBF 111828
0°C to 70°C
LT1118CST-5#TRPBF
TAPE AND REEL
11185
0°C to 70°C
PART MARKING*
1118
TEMPERATURE RANGE
0°C to 70°C
LT1118CS8#TR
LT1118CS8-2.5
LT1118CS8-2.5#TR
LT1118CS8-2.85#TR
LT1118CS8-5#TR
LT1118CST-2.5#TR
LT1118CST-2.85#TR
LT1118CST-5#TR
111825
111828
11185
8-Lead Plastic SO
0°C to 70°C
LT1118CS8-2.85
LT1118CS8-5
8-Lead Plastic SO
0°C to 70°C
8-Lead Plastic SO
0°C to 70°C
LT1118CST-2.5
111825
111828
11185
3-Lead Plastic SOT-223
3-Lead Plastic SOT-223
3-Lead Plastic SOT-223
0°C to 70°C
LT1118CST-2.85
LT1118CST-5
0°C to 70°C
0°C to 70°C
Consult LTC Marketing for parts specified with wider operating temperature ranges.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
1118fd
2
LT1118/LT1118-2.5
LT1118-2.85/LT1118-5
ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 2)
PARAMETER
Quiescent Current (V )
CONDITIONS
MIN
TYP
0.6
1
MAX
1
UNITS
mA
l
l
V
EN
V
EN
= 5V
= 0V
IN
Quiescent Current in Shutdown (V )
10
μA
IN
l
l
Enable Input Thresholds
Input Low Level
Input High Level
0.4
–1
1.4
1.4
V
V
2
l
l
l
l
l
Enable Input Current
Feedback Voltage
0V ≤ V ≤ 5V
25
μA
EN
No Load (25°C) (LT1118)
All Operating Conditions (Note 3)
1.213
1.200
1.225
1.225
1.237
1.250
V
V
Output Voltage
No Load (25°C) (LT1118-2.5)
All Operating Conditions (Note 3)
2.47
2.45
2.5
2.5
2.53
2.55
V
V
No Load (25°C) (LT1118-2.85)
All Operating Conditions (Note 3)
2.82
2.79
2.85
2.85
2.88
2.91
V
V
No Load (25°C) (LT1118-5)
All Operating Conditions (Note 3)
4.95
4.90
5
5
5.05
5.10
V
V
l
l
l
l
Line Regulation (Note 4)
Load Regulation (Note 4)
I = 0mA, 4.2V ≤ V ≤ 15V (LT1118)
6
6
mV
mV
mV
mV
L
IN
I = 0mA, 4.2V ≤ V ≤ 15V (LT1118-2.5)
L
IN
I = 0mA, 4.75V ≤ V ≤ 15V (LT1118-2.85)
6
L
IN
I = 0mA, 6.5V ≤ V ≤ 15V (LT1118-5)
10
L
IN
l
l
0mA ≤ I ≤ 800mA (LT1118)
6
6
mV
mV
L
–400mA ≤ I ≤ 0mA
L
l
l
0mA ≤ I ≤ 800mA (LT1118-2.5)
12
12
mV
mV
L
–400mA ≤ I ≤ 0mA
L
l
l
0mA ≤ I ≤ 800mA (LT1118-2.85)
12
12
mV
mV
L
–400mA ≤ I ≤ 0mA
L
l
l
0mA ≤ I ≤ 800mA (LT1118-5)
25
25
mV
mV
L
–400mA ≤ I ≤ 0mA
L
Dropout Voltage (Note 5)
I = 100mA
L
0.85
1
1.1
1.3
V
V
L
I = 800mA
FB Pin Bias Current
Minimum Output Voltage
Ripple Rejection
LT1118
LT1118
0.35
1
μA
V
l
2.1
f
= 120Hz, V – V = 2V
OUT
60
80
dB
RIPPLE
IN
V
= 0.5V
P-P
RIPPLE
Load Transient Settling Time,
ΔV = 1%
0mA ≤ I ≤ 800mA, C
= 1μF
LOAD
5
5
μs
μs
L
–400mA ≤ I ≤ 0mA, C
= 1μF
LOAD
L
Output Short-Circuit Current
V
V
= 0V, Sourcing
800
1200
–700
mA
mA
OUT
OUT
= V , Sinking
–400
IN
Thermal Shutdown Junction Temperature
Enable Turn-On Delay
No Load
No Load
170
50
°C
μs
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 3: All operating conditions include the combined effects of load
current, input voltage and temperature over each parameter’s full range.
Note 4: Load and line regulation are tested at a constant junction
temperature by low duty cycle pulse testing.
Note 2: Unless otherwide specified, testing done at V = 5V
Note 5: Dropout voltage is defined as the minimum input to output voltage
measured while sourcing the specified current.
CC
(LT1118-2.5, LT1118-2.85) or V = 7V (LT1118-5). V = V .
CC
EN
CC
Output C
= 1μF, I
= 0.
LOAD
LOAD
1118fd
3
LT1118/LT1118-2.5/
LT1118-2.85/LT1118-5
TYPICAL PERFORMANCE CHARACTERISTICS
Dropout Voltage vs Output Current
Ripple Rejection vs Frequency
Ripple Rejection vs Frequency
80
60
40
20
0
1.4
1.2
1
80
60
40
20
0
800mA
400mA
T
= 75°C
J
T
= 25°C
J
10mA
10mA
0.8
0.6
0.4
0.2
0
T
= 125°C
J
NO LOAD
NO LOAD
SOURCING CURRENT
SINKING CURRENT
100
10
100
1k
10k
100k
10
1k
10k
100k
0
200
400
600
800
FREQUENCY (Hz)
FREQUENCY (Hz)
OUTPUT CURRENT (mA)
1118 G02
1118 G03
1118 G01
Output Impedance vs Frequency
Feedback Current vs Temperature
Ripple Rejection vs Load Current
10
1
450
80
60
40
20
0
C
= C
= 1μF
LOAD
IN
400
350
300
250
200
150
100
50
NO CURRENT
100mA SOURCE
10mA SOURCE
0.1
0.01
0.001
100mA SINK
10mA SINK
0
2
3
4
5
6
–400 –200
0
200
400
600
800
–55 –35 –15
5
25 45 65 85 105 125
10
10
10
FREQUENCY (Hz)
10
10
LOAD CURRENT (mA)
TEMPERATURE (°C)
1118 G04
1118 G06
1118 G05
Input Current
vs Output Sink Current
Ground Pin Current
vs Output Source Current
2000
1750
1500
1250
1000
750
800
700
600
500
400
300
200
100
500
250
0
0
0
200 250
0
50 100 150
300 350 400
400
OUTPUT SOURCING CURRENT (mA)
200
600
800
OUTPUT SINK CURRENT (mA)
1118 G07
1118 G08
1118fd
4
LT1118/LT1118-2.5
LT1118-2.85/LT1118-5
PIN FUNCTIONS
IN: Input Supply Pin. This pin should be decoupled with
a 1μF or larger low ESR capacitor. The two IN pins on the
SO-8 package must be directly connected on the printed
circuit board to prevent voltage drops between the two
inputs. When used as a SCSI active termination, IN con-
nects to term power. When used as a supply splitter, IN is
also the positive supply output.
OUT: Regulated Output Voltage. Output can source or sink
current. Current limit for sourcing and sinking current is
provided to protect the device from fault conditons. The
output must have a low ESR output filter capacitor. C
OUT
≥ 0.22μF to guarantee stability. A 0.1μF ceramic capacitor
may be needed in parallel with C if the ESR of the main
OUT
C
is too high.
OUT
GND: Ground Pin. The multiple GND pins on the SO-8
packageareinternallyconnected,butlowestloadregulation
errors will result if these pins are tightly connected on the
printed circuit board. This will also aid heat dissipation at
high power levels.
FB: Feedback Pin. The feedback pin is used to program
the output voltage of the adjustable S8 part. The output
voltage range that can be achieved is 2.1V to 6.5V. The
output voltage is determined by the selection of feedback
resistors defined by the following formula:
EN: TTL/CMOS Logic Input. A high level allows normal
V
= V (1 + R /R ) + I R
OUT
FB
1
2
FB 1
operation. A low level reduces supply current to zero. This
pin is internally connected to V on 3-lead ST packaged
IN
LT1118 Adjustable
devices.
R
R
1
V
IN
OUT
V
OUT
= V 1 +
+ I
R
FB 1
IN
FB
(
)
2
1μF
1μF
LT1118
GND
R
R
1
2
EN
FB
1118 TA06
OPERATION
Output Capacitor
Worst case transient response of the LT1118 regulators
occursatzerooutputcurrent. Inordertoobtainthefastest
transient settling performance, the regulator output may
be preloaded with a small current. The preload current
reduces the regulator output impedance, reducing output
voltage settling time.
The LT1118 family of voltage regulators require an output
capacitor for stability. The regulators are stable with out-
put capacitors larger than 0.2μF. Load transient response
is very sensitive to output capacitor value and dielectric
choice. Low ESR ceramic capacitors are the best choice
for fast settling to load transients. Output capacitors
between 0.2μF and 1μF give good performance in most
applications. Larger tantalum output capacitors may be
used to reduce load transient amplitudes. Larger capaci-
tors should be paralleled with a 0.1μF ceramic capacitor
to maintain quick settling time performance and to insure
stability of the regulator control loop. Capacitors larger
than 10μF may be safely used with the regulators, but
little transient settling performance improvement results
from their use.
Thermal Considerations
TheLT1118regulatorsarepackagedinplasticSOT-223and
fused lead S8 packages. These small footprint packages
are unable to convectively dissipate the heat generated
when the regulator is operating at high current levels. In
order to control die operating temperatures, the PC board
layout should allow for maximum possible copper area at
the ground pins of the LT1118. The ground pins and the
tab on the SOT-223 package are electrically and thermally
1118fd
5
LT1118/LT1118-2.5/
LT1118-2.85/LT1118-5
OPERATION
connected to the die substrate. Table 1 shows measured
thermalresistancefromjunctiontoambientfortheLT1118
connected to various sized PC board ground planes. The
power dissipated in the LT1118 varies with input voltage
and loading. When the regulator is sourcing current the
power which must be dissipated by the package is:
When the regulator is sinking load current, power dissipa-
tion is nearly independent of V and can be calculated
IN
as:
P = V
• I
D
OUT LOAD
Heat sinking to the IC package must consider the worst
case power dissipation which may occur.
P = (V – V ) • I
LOAD
D
IN
OUT
Table 1. Measured Thermal Resistance from Junction to Ambient
for the LT1118
S8 Package
SOT-223
Free Air
1 Sq Inch Copper
120°C/W
55°C/W
95°C/W
53°C/W
4 Sq Inch Copper
35°C/W
38°C/W
TYPICAL APPLICATIONS
SCSI Active Terminator
110Ω
•
•
•
•
TERMPWR
110Ω
110Ω
110Ω
27 LINES
LT1118-2.85 OUT
GND
IN
•
•
•
•
110Ω
+
5V
2.2μF
1μF
1118 TA03
Power Supply Splitter
V
IN
5V
5V
ANALOG
COMMON
2.5V
LT1118-2.5 OUT
GND
IN
1μF
1μF
1118 TA04
1118fd
6
LT1118/LT1118-2.5
LT1118-2.85/LT1118-5
PACKAGE DESCRIPTION
ST Package
3-Lead Plastic SOT-223
(Reference LTC DWG # 05-08-1630)
.248 – .264
(6.30 – 6.71)
.129 MAX
.114 – .124
(2.90 – 3.15)
.059 MAX
.264 – .287
(6.70 – 7.30)
.248 BSC
.130 – .146
(3.30 – 3.71)
.039 MAX
.059 MAX
.090
BSC
.181 MAX
RECOMMENDED SOLDER PAD LAYOUT
.033 – .041
(0.84 – 1.04)
.0905
(2.30)
BSC
10° – 16°
.010 – .014
10°
MAX
.071
(1.80)
MAX
(0.25 – 0.36)
10° – 16°
.0008 – .0040
(0.0203 – 0.1016)
.024 – .033
(0.60 – 0.84)
.012
(0.31)
MIN
.181
(4.60)
BSC
ST3 (SOT-233) 0502
S8 Package
8-Lead Plastic Small Outline (Narrow 0.150)
(Reference LTC DWG # 05-08-1610)
.189 – .197
(4.801 – 5.004)
NOTE 3
.045 .005
.050 BSC
7
5
8
6
.245
MIN
.160 .005
.150 – .157
(3.810 – 3.988)
NOTE 3
.228 – .244
(5.791 – 6.197)
.030 .005
TYP
1
3
4
2
RECOMMENDED SOLDER PAD LAYOUT
.010 – .020
(0.254 – 0.508)
× 45°
.053 – .069
(1.346 – 1.752)
.004 – .010
(0.101 – 0.254)
.008 – .010
(0.203 – 0.254)
0°– 8° TYP
.016 – .050
(0.406 – 1.270)
.050
(1.270)
BSC
.014 – .019
(0.355 – 0.483)
TYP
NOTE:
INCHES
1. DIMENSIONS IN
(MILLIMETERS)
2. DRAWING NOT TO SCALE
3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
SO8 0303
1118fd
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-
tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
7
LT1118/LT1118-2.5/
LT1118-2.85/LT1118-5
TYPICAL APPLICATION
Variable 2.1V to 6.5V Regulator with DIgital Control
12V
0.1μF
IN
OUT
FB
V
OUT
1μF
0.22μF
R
1
LT1118
GND
V
D
IN
CC
13.3k
R
2
6.19k
V
DAC
μP
V
LTC1257
GND
CLK
LOAD
EN
OUT
R
3
V
REF
6.19k
1118 TA05
R
1
R
1
V
OUT
= 1.225 1 +
– V
DAC
R
|| R
R
2
2
3
)
(
RELATED PARTS
PART NUMBER DESCRIPTION
COMMENTS
V : 4.2V to 30V, V
LT1129
700mA, Micropower, LDO
= 3.8V, V = 0.40V, I = 50μA, I = 16μA;
OUT(MIN) DO Q SD
IN
DD, SOT-223, S8, TO220-5 and TSSOP20 Packages
LT1206
LT1210
LT1763
250mA/60MHz Current Feedback Amplifier High Output Current Drive Capability, Can Sink/Source
1.1A, 35MHz Current Feedback Amplifer
500mA, Low Noise Micropower, LDO
High Output Current Drive Capability, Can Sink/Source
V : 1.8V to 20V, V = 1.22V, V = 0.30V, I = 30μA, I = < 1μA,
IN
OUT(MIN)
DO
Q
SD
Low Noise < 20μV
, S8 Package
RMS
LT1764/
LT1764A
3A, Low Noise, Fast Transient Response,
LDO
V : 2.7V to 20V, V
= 1.21V, V = 0.34V, I = 1mA, I = < 1μA, Low Noise
OUT(MIN) DO Q SD
IN
< 40μV
, “A” Version Stable with Ceramic Capacitors, DD and TO220-5 Packages
RMS
LTC1844
150mA, Very Low Drop-Out LDO
V : 1.6V to 6.5V, V
= 1.25V, V = 0.08V, I = 35μA, I = < 1μA,
IN
OUT(MIN) DO Q SD
Low Noise < 60μV
, ThinSOT™ Package
RMS
LT1962
300mA, Low Noise Micropower, LDO
V : 1.8V to 20V, V
= 1.22V, V = 0.27V, I = 30μA, I = < 1μA,
OUT(MIN) DO Q SD
IN
Low Noise < 20μV
, MS8 Package
RMS
LT1963/
LT1963A
1.5A, Low Noise, Fast Transient Response, V : 2.1V to 20V, V
= 1.21V, V = 0.34V, I = 1mA, I = < 1μA,
OUT(MIN) DO Q SD
IN
LDO
Low Noise < 40μV
, “A” Version Stable with Ceramic Capacitors;
RMS
DD, TO220-5, SOT-223 and S8 Packages
LT3021
LT3024
LT3028
500mA, Low Voltage V , V
= 0.9V, V : 0.9V to 10V, V
= 0.20V, V = 0.16V, I = 120μA, I = 3μA, DFN and
DO Q SD
DO IN(MIN)
IN
OUT(MIN)
OUT(MIN)
OUT(MIN)
LDO
S8 Packages
Dual, 100mA/500mA, Low Noise
Micropower, LDO
V : 1.8V to 20V, V
= 1.22V, V = 0.30V, I = 60μA, I = < 1μA, DFN and
DO Q SD
IN
TSSOP Packages
Dual, 100mA/500mA, Low Noise
Micropower, LDO with Independent Inputs Low Noise < 20μV
V : 1.8V to 20V, V
= 1.22V, V = 0.30V, I = 30μA, I = < 1μA,
DO Q SD
, DFN and TSSOP Packages
IN
RMS
LT3080/
LT3080-1
1.1A Parallelable, Low Noise, Low Dropout 300mV Dropout Voltage (2-Supply Operation), Low Noise: 40μV
, V : 1.2V to 36V, V
:
RMS IN
OUT
Linear Regulator
0V to 35.7V, Current-Based Reference with 1-Resistor V
Set; Directly Parallelable (No Op
OUT
Amp Required), Stable with Ceramic Caps, TO-220, SOT-223, MSOP and 3mm × 3mm DFN
Packages; LT3080-1 Version Has Integrated Internal Ballast Resistor
LT3085
500mA, Parallelable Low Noise Low
Dropout Linear Regulator
275mV Dropout Voltage (2 Supply Operation), Low Noise: 40μV
OUT
, V : 1.2V to 36V,
RMS IN
V
: 0V to 35.7V, Current Reference, MSOP-8 and 2mm × 3mm DFN-6 Packages
ThinSOT is a trademark of Linear Technology Corporation
1118fd
LT 0209 REV D • PRINTED IN USA
LinearTechnology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
8
●
●
© LINEAR TECHNOLOGY CORPORATION 1995
(408) 432-1900 FAX: (408) 434-0507 www.linear.com
相关型号:
LT1118CS8-2.5#TRPBF
LT1118 - Low IQ, Low Dropout, 800mA, Source and Sink Regulators Adjustable and Fixed 2.5V, 2.85V, 5V Output; Package: SO; Pins: 8; Temperature Range: 0°C to 70°C
Linear
LT1118CS8-2.85
Low IQ, Low Dropout, 800mA, Source and Sink Regulators Adjustable and Fixed 2.5V, 2.85V, 5V Output
Linear
LT1118CS8-2.85#TR
LT1118 - Low IQ, Low Dropout, 800mA, Source and Sink Regulators Adjustable and Fixed 2.5V, 2.85V, 5V Output; Package: SO; Pins: 8; Temperature Range: 0°C to 70°C
Linear
LT1118CS8-2.85#TRPBF
LT1118 - Low IQ, Low Dropout, 800mA, Source and Sink Regulators Adjustable and Fixed 2.5V, 2.85V, 5V Output; Package: SO; Pins: 8; Temperature Range: 0°C to 70°C
Linear
LT1118CS8-5
Low IQ, Low Dropout, 800mA, Source and Sink Regulators Adjustable and Fixed 2.5V, 2.85V, 5V Output
Linear
LT1118CS8-5#PBF
LT1118 - Low IQ, Low Dropout, 800mA, Source and Sink Regulators Adjustable and Fixed 2.5V, 2.85V, 5V Output; Package: SO; Pins: 8; Temperature Range: 0°C to 70°C
Linear
LT1118CS8-5#TRPBF
LT1118 - Low IQ, Low Dropout, 800mA, Source and Sink Regulators Adjustable and Fixed 2.5V, 2.85V, 5V Output; Package: SO; Pins: 8; Temperature Range: 0°C to 70°C
Linear
LT1118CST-2.5
Low IQ, Low Dropout, 800mA, Source and Sink Regulators Adjustable and Fixed 2.5V, 2.85V, 5V Output
Linear
LT1118CST-2.5#TR
LT1118 - Low IQ, Low Dropout, 800mA, Source and Sink Regulators Adjustable and Fixed 2.5V, 2.85V, 5V Output; Package: SOT; Pins: 3; Temperature Range: 0°C to 70°C
ADI
©2020 ICPDF网 联系我们和版权申明