OP421HP [ADI]
IC QUAD OP-AMP, 6000 uV OFFSET-MAX, 1.9 MHz BAND WIDTH, PDIP14, PLASTIC, DIP-14, Operational Amplifier;
| 型号： | OP421HP |
| 厂家： | 
ADI |
| 描述： | IC QUAD OP-AMP, 6000 uV OFFSET-MAX, 1.9 MHz BAND WIDTH, PDIP14, PLASTIC, DIP-14, Operational Amplifier 放大器 光电二极管 |
| 文件： | 总10页 (文件大小：81K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
APPROVED
A
B
C
00-11-27
04-08-06
11-03-08
R. MONNIN
R. MONNIN
C. SAFFLE
Update boilerplate to meet current requirements. –rrp
Replaced reference to MIL-STD-973 with reference to MIL-PRF-38535. -gt
Update drawing to reflect current requirements. -rrp
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
REV
C
1
C
2
C
3
C
4
C
5
C
6
C
7
C
8
C
9
SHEET
PREPARED BY
JOSEPH A. KERBY
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.dscc.dla.mil
STANDARD
MICROCIRCUIT
DRAWING
CHECKED BY
RAY MONNIN
APPROVED BY
MICHAEL A. FRYE
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
MICROCIRCUIT, LINEAR, LOW POWER
OPERATIONAL AMPLIFIER, MONOLITHIC
SILICON
DRAWING APPROVAL DATE
89-03-09
REVISION LEVEL
C
SIZE
A
CAGE CODE
AMSC N/A
5962-88559
67268
SHEET
1 OF 9
DSCC FORM 2233
APR 97
5962-E238-11
1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
5962-88559
01
C
A
Drawing number
Device type
(see 1.2.1)
Case outline
(see 1.2.2)
Lead finish
(see 1.2.3)
1.2.1 Device type(s). The device type(s) identify the circuit function as follows:
Device type
Generic number
Circuit function
01
02
OP421B
OP421C
Quad low-power operational amplifier
Quad low-power operational amplifier
1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
C
Descriptive designator
Terminals
8
Package style
Dual-in-line
GDIP1-T14 or CDIP2-T14
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
1.3 Absolute maximum ratings.
Supply voltage:
V+ .............................................................................................. +18 V
V- ............................................................................................... -18 V
Differential input voltage ................................................................ +30 V or -30 V
Input voltage (VIN) ......................................................................... Supply voltage
Internal power dissipation (PD) ...................................................... 500 mW 1/
Storage temperature range ........................................................... -65°C to +150°C
Lead temperature (soldering, 60 seconds) .................................... +300°C
Junction temperature (TJ) .............................................................. +150°C
Thermal resistance, junction-to-case (θJC) .................................... See MIL-STD-1835
1.4 Recommended operating conditions.
Ambient operating temperature range (TA) .................................... -55°C to +125°C
1/ Derate above TA = +100°C, 10 mW/°C.
SIZE
STANDARD
5962-88559
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
SHEET
COLUMBUS, OHIO 43218-3990
C
2
DSCC FORM 2234
APR 97
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883
-
Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-
JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-
PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying
activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan
may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.
These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-
PRF-38535 is required to identify when the QML flow option is used.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535, appendix A and herein.
3.2.1 Case outline. The case outline shall be in accordance with 1.2.2 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN
listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD
PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device.
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
SIZE
STANDARD
5962-88559
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
C
SHEET
COLUMBUS, OHIO 43218-3990
3
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics.
Conditions
Test
Symbol
VIO
Group A
subgroups
Device
types
Limits
Units
-55°C ≤ TA ≤ +125°C
V+ = 15 V, V- = -15 V
unless otherwise specified
V+ = +2.5 V to +15 V,
V- = -2.5 V to -15 V
Min
Max
Input offset
voltage
1
2, 3
1
01
02
mV
±2.5
±3.5
±4.0
±5.5
2, 3
Input offset
current
IIO
V+ = +2.5 V to +15 V,
V- = -2.5 V to -15 V
1
2, 3
1
01
02
nA
nA
V
±5.0
±8.0
±10.0
±15.0
2, 3
Input bias
current
IB
V+ = +2.5 V to +15 V,
V- = -2.5 V to -15 V
1
2, 3
1
01
02
±50
±70
±80
±125
2, 3
Input voltage
range 1/
IVR
CMRR
V+ = 5 V, V- = 0 V
1
2, 3
1
All
0
0
+3.5
+3.2
+13.5
+13.2
V+ = 15 V, V- = -15 V
-15.0
-15.0
2, 3
Common
mode rejection
V+ = +5 V, V- = 0 V,
0 V ≤ VCM ≤ +3.5 V
V+ = +5 V, V- = 0 V,
0 V ≤ VCM ≤ +3.2 V
V+ = +5 V, V- = 0 V,
0 V ≤ VCM ≤ +3.5 V
V+ = +5 V, V- = 0 V,
0 V ≤ VCM ≤ +3.2 V
-15 V ≤ VCM ≤ +13.5 V,
V+ = 15 V, V- = -15 V
4
01
02
83
78
80
74
dB
5, 6
4
5, 6
4
5, 6
4
5, 6
4
5, 6
4
5, 6
01
02
01
02
83
78
80
74
Power supply
rejection ratio
PSRR
V+ = 2.5 V, V- = -2.5 V,
V+ = 15 V, V- = -15 V,
V+ = 5 V, V- = 0 V,
30
50
50
80
µV/V
V- to V+ = 5 V to 30 V
See footnotes at end of table.
SIZE
STANDARD
5962-88559
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
C
SHEET
COLUMBUS, OHIO 43218-3990
4
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics – Continued.
Conditions
Test
Symbol
ISY
Group A
subgroups
Device
types
Limits
Units
-55°C ≤ TA ≤ +125°C
V+ = 15 V, V- = -15 V
unless otherwise specified
V+ = 2.5 V, V- = -2.5 V,
no load
Min
Max
Supply current
(four amplifiers)
1
2, 3
1
2, 3
1
2, 3
1
2, 3
4
01
02
01
02
01
1.0
mA
1.5
1.5
2.0
1.8
2.5
2.3
3.2
V+ = 15 V, V- = -15 V,
no load
Large-signal
voltage gain
AVO
200
V/mV
VO = ±10 V,
RL = 10 kΩ
VO = ±10 V,
RL = 20 kΩ
VO = ±10 V,
RL = 10 kΩ
VO = ±10 V,
RL = 20 kΩ
5, 6
4
100
100
50
02
5, 6
Output voltage
swing
VO
V+ = 5 V,
V- = 0 V
4
4
5, 6
5, 6
4
4
5, 6
5, 6
01
02
01
02
01
02
01
02
0.7
0.8
0.8
0.9
+4.0
+3.9
+3.9
+3.8
+14
+13.9
+13.8
+13.7
V
RL = 5 kΩ
RL = 10 kΩ
RL = 10 kΩ
RL = 20 kΩ
V+ = 15 V,
V- = -15 V
-14
-13.9
-13.8
-13.7
Slew rate 2/
SR
CS
7
7
All
All
0.25
100
TA = +25°C
TA = +25°C
V/µs
Channel
separation 2/
dB
Input noise
voltage density
2/
En
7
7
All
All
40
30
fO = 10 Hz, TA = +25°C
fO = 100 Hz, TA = +25°C
nV/ Hz
Input noise
current density
2/
In
0.6
0.4
fO = 10 Hz, TA = +25°C
fO = 100 Hz, TA = +25°C
pA/ Hz
µV/°C
Average input
offset voltage
drift
TCVIO
2, 3
01
02
-10
-15
10
15
1/ IVR is guaranteed by CMRR test.
2/ Guaranteed if not tested.
SIZE
STANDARD
5962-88559
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
C
SHEET
COLUMBUS, OHIO 43218-3990
5
DSCC FORM 2234
APR 97
Device types
Case outline
01 and 02
C
Terminal number
Terminal symbol
OUT 1
-IN 1
1
2
3
+IN 1
4
V+
5
+IN 2
6
-IN 2
7
8
9
OUT 2
OUT 3
-IN 3
10
11
12
13
14
+IN 3
V-
+IN 4
-IN 4
OUT 4
FIGURE 1. Terminal connections.
SIZE
STANDARD
5962-88559
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
C
SHEET
COLUMBUS, OHIO 43218-3990
6
DSCC FORM 2234
APR 97
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and
Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturer's product meets the
requirements of MIL-PRF-38535, appendix A and the requirements herein.
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
with each lot of microcircuits delivered to this drawing.
3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for any change that
affects this drawing.
3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritime 's agent, and the acquiring activity retain the
option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made
available onshore at the option of the reviewer.
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535,
appendix A.
4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices
prior to quality conformance inspection. The following additional criteria shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify
the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method
1015 of MIL-STD-883.
(2) TA = +125°C, minimum.
b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-
883 including groups A, B, C, and D inspections. The following additional criteria shall apply.
4.3.1 Group A inspection.
a. Tests shall be as specified in table II herein.
b. Subgroups 8, 9, 10, and 11 in table I, method 5005 of MIL-STD-883 shall be omitted.
SIZE
STANDARD
5962-88559
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
C
SHEET
COLUMBUS, OHIO 43218-3990
7
DSCC FORM 2234
APR 97
TABLE II. Electrical test requirements.
MIL-STD-883 test requirements
Subgroups
(in accordance with
MIL-STD-883, method 5005,
table I)
1, 4
Interim electrical parameters
(method 5004)
Final electrical test parameters
(method 5004)
1*, 2, 3, 4, 5, 6
1, 2, 3, 4, 5, 6, 7
1
Group A test requirements
(method 5005)
Groups C and D end-point
electrical parameters
(method 5005)
* PDA applies to subgroup 1.
4.3.2 Groups C and D inspections.
a. End-point electrical parameters shall be as specified in table II herein.
b. Steady-state life test conditions, method 1005 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision
level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
method 1005 of MIL-STD-883.
(2) TA = +125°C, minimum.
(3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-
prepared specification or drawing.
SIZE
STANDARD
5962-88559
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
C
SHEET
COLUMBUS, OHIO 43218-3990
8
DSCC FORM 2234
APR 97
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for
the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.
6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires
configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this
list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics
devices (FSC 5962) should contact DLA Land and Maritime -VA, telephone (614) 692-0544.
6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime -VA, Columbus, Ohio 43218-
3990, or telephone (614) 692-0540.
6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MIL-
HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by
DLA Land and Maritime -VA.
SIZE
STANDARD
5962-88559
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
C
SHEET
COLUMBUS, OHIO 43218-3990
9
DSCC FORM 2234
APR 97
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 11-03-08
Approved sources of supply for SMD 5962-88559 are listed below for immediate acquisition information only and
shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DLA Land and Maritime -VA. This information
bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DLA Land and Maritime
maintains an online database of all current sources of supply at http://www.dscc.dla.mil/Programs/Smcr/.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
Vendor
similar
PIN 2/
number
5962-8855901CA
5962-8855902CA
3/
3/
OP421BY
OP421CY
1/ The lead finish shown for each PIN representing
a hermetic package is the most readily available
from the manufacturer listed for that part. If the
desired lead finish is not listed contact the vendor
to determine its availability.
2/ Caution. Do not use this number for item
acquisition. Items acquired to this number may not
satisfy the performance requirements of this drawing.
3/ Not available from an approved source of supply.
The last known source is listed below.
Vendor CAGE
number
Vendor name
and address
24355
Analog Devices
RT 1 Industrial Park
PO Box 9106
Norwood, MA 02062
Point of contact: 7910 Triad Center Drive
Greensboro, NC 27409-9605
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.
相关型号：
OP421HS
IC QUAD OP-AMP, 6000 uV OFFSET-MAX, 1.9 MHz BAND WIDTH, PDSO16, SOL-16, Operational Amplifier
ADI
OP421HSR
IC QUAD OP-AMP, 7500 uV OFFSET-MAX, 1.9 MHz BAND WIDTH, PDSO14, SOL-14, Operational Amplifier
ADI
OP421N
IC QUAD OP-AMP, 2500 uV OFFSET-MAX, 1.9 MHz BAND WIDTH, UUC14, 2.36 X 2.21 MM, DIE-14, Operational Amplifier
ADI
OP42AJ/883
IC OP-AMP, 2000 uV OFFSET-MAX, 10 MHz BAND WIDTH, MBCY8, TO-99, 8 PIN, Operational Amplifier
ADI
OP42AJ/883C
IC OP-AMP, 2000 uV OFFSET-MAX, 10 MHz BAND WIDTH, MBCY8, TO-99, 8 PIN, Operational Amplifier
ADI
©2020 ICPDF网 联系我们和版权申明