SSM2167-1RMZ-REEL [ADI]
Low Voltage Microphone Preamplifier with Variable Compression and Noige Gating; 低电压麦克风前置放大器，可变压缩和Noige门控
| 型号： | SSM2167-1RMZ-REEL |
| 厂家： | 
ADI |
| 描述： | Low Voltage Microphone Preamplifier with Variable Compression and Noige Gating |
| 文件： | 总12页 (文件大小：267K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Low Voltage Microphone Preamplifier with
Variable Compression and Noise Gating
SSM2167
PIN CONFIGURATION
FEATURES
Complete microphone conditioner in a 10-lead package
Single 3 V operation
Low shutdown current < 2 μA
Adjustable noise gate threshold
Adjustable compression ratio
GND
1
2
3
4
5
10
V
DD
VCA
9
OUTPUT
IN
SSM2167
TOP VIEW
(Not to Scale)
SHUTDOWN
8
COMPRESSION RATIO
GATE THRS
AVG CAP
BUF
7
OUT
INPUT
6
Figure 1. 10-Lead MSOP (RM Suffix)
Automatic limiting feature prevents ADC overload
Low noise and distortion: 0.2% THD + N
20 kHz bandwidth
LIMITING
THRESHOLD
LIMITING
REGION
(ROTATION POINT)
APPLICATIONS
Desktop, portable, or palmtop computers
Telephone conferencing
Communication headsets
Two-way communications
Surveillance systems
COMPRESSION
REGION
DOWNWARD
EXPANSION
THRESHOLD
(NOISE GATE)
VCA GAIN
1
r
Karaoke and DJ mixers
DOWNWARD
EXPANSION
REGION
GENERAL DESCRIPTION
1
The SSM2167 is a complete and flexible solution for conditioning
microphone inputs in personal electronics and computer audio
systems. It is also excellent for improving vocal clarity in com-
munications and public address systems. A low noise voltage
controlled amplifier (VCA) provides a gain that is dynamically
adjusted by a control loop to maintain a set compression charac-
teristic. The compression ratio is set by a single resistor and can
be varied from 1:1 to over 10:1 relative to the fixed rotation
point. Signals above the rotation point are limited to prevent
overload and to eliminate popping. A downward expander (noise
gate) prevents amplification of background noise or hum. This
results in optimized signal levels prior to digitization, thereby
eliminating the need for additional gain or attenuation in the
digital domain. The flexibility of setting the compression ratio
and the time constant of the level detector, coupled with two
values of rotation point, make the SSM2167 easy to integrate in
a wide variety of microphone conditioning applications.
1
V
V
RP
DE
INPUT (dB)
Figure 2. General Input/Output Characteristics
The device is available in a 10-lead MSOP package, and is
guaranteed for operation over the extended industrial
temperature range of −40°C to +85°C.
Rev. C
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2001–2007 Analog Devices, Inc. All rights reserved.
SSM2167
TABLE OF CONTENTS
Features .............................................................................................. 1
Signal Path......................................................................................8
Level Detector................................................................................9
Control Circuitry...........................................................................9
Setting the Compression Ratio....................................................9
Applications....................................................................................... 1
General Description......................................................................... 1
Pin Configuration............................................................................. 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Absolute Maximum Ratings............................................................ 4
Thermal Resistance ...................................................................... 4
ESD Caution.................................................................................. 4
Typical Performance Characteristics ............................................. 5
Applications Information ................................................................ 8
Theory of Operation .................................................................... 8
Setting the Noise Gate Threshold
(Downward Expansion) ............................................................ 10
Rotation Point (Limiting).......................................................... 10
Shutdown Feature....................................................................... 10
PCB Layout Considerations...................................................... 10
Outline Dimensions....................................................................... 11
Ordering Guide .......................................................................... 11
REVISION HISTORY
3/02—Rev. 0 to Rev. A
11/07—Rev. B to Rev. C
Edits to Specifications.......................................................................2
Edits to Figure 2 and Figure 3..........................................................6
Updated Format..................................................................Universal
Changes to PSRR .............................................................................. 3
Updated Outline Dimensions....................................................... 11
Changes to Ordering Guide .......................................................... 11
7/01—Revision 0: Initial Version
9/03—Rev. A to Rev. B
Deleted SSM2167-2 Model................................................Universal
Changes to Ordering Guide ............................................................ 3
Edits to Figure 2 and Figure 3......................................................... 6
Updated Outline Dimensions......................................................... 9
Rev. C | Page 2 of 12
SSM2167
SPECIFICATIONS
VS = 3.0 V, f = 1 kHz, RL = 100 kΩ, RCOMP = 0 Ω, TA = 25°C, VIN = 100 mV rms, RGATE = 2 kΩ, unless otherwise noted.
Table 1.
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
AUDIO SIGNAL PATH
Voltage Noise Density
Noise
Total Harmonic Distortion + Noise
Input Impedance
Output Impedance
Load Drive
en
10:1 compression
20 kHz bandwidth, VIN = GND
VIN = 100 mV rms
20
nV/√Hz
dBV
%
kΩ
Ω
kΩ
nF
mV rms
mV rms
MHz
−70
0.2
100
145
5
THD + N
ZIN
ZOUT
Minimum resistive load
Maximum capacitive load
0.4% THD + N
0.4% THD + N
1:1 compression, VCA G = 18 dB
2
Input Voltage Range
Output Voltage Range
Gain Bandwidth Product
CONTROL SECTION
VCA Dynamic Gain Range
VCA Fixed Gain
600
700
1
40
18
dB
dB
Compression Ratio, Minimum
Compression Ratio, Maximum
Rotation Point
1:1
10:1
63
See Table 4 for RCOMP
Maximum threshold
mV rms
dBV
Noise Gate Range
−40
POWER SUPPLY
Supply Voltage
Supply Current
DC Output Voltage
Power Supply Rejection Ratio
SHUTDOWN
VSY
ISY
2.5
5.5
5
V
mA
V
2.3
1.4
45
PSRR
ISY
VSY = 2.5 V to 6 V
Pin 3 = GND
dB
Supply Current
2
8
μA
Rev. C | Page 3 of 12
SSM2167
ABSOLUTE MAXIMUM RATINGS
Table 2.
THERMAL RESISTANCE
θJA is specified for worst-case conditions, that is, θJA is specified
for device soldered in 4-layer circuit board for surface-mount
packages.
Parameter
Rating
6 V
6 V
Supply Voltage
Input Voltage
Operating Temperature Range
Junction Temperature
Lead Temperature (Soldering, 10 sec)
883 (Human Body) Model
−40°C to +85°C
150°C
300°C
Table 3.
Package Type
θJA
θJC
Unit
10-Lead MSOP (RM)
180
35
°C/W
500 V
ESD CAUTION
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. C | Page 4 of 12
SSM2167
TYPICAL PERFORMANCE CHARACTERISTICS
100
1
T
= 25°C
A
V+ = 3V
R
= 100kΩ
LOAD
COMPRESSION RATIO 2:1
ROTATION POINT = 63mV rms
10
0.1
T
= 25°C
A
V+ = 3V
V
FREQUENCY = 1kHz
IN
R
= 100kΩ
LOAD
COMPRESSION RATIO 1:1
ROTATION POINT = 63mV rms
NOISE GATE SETTING = 1.4V rms
1
0.01
0
500
1000
1500
2000
2500
3000
3500
0.01
0.1
1
R
(Ω)
INPUT VOLTAGE (V rms)
GATE
Figure 6. THD + N vs. Input
Figure 3. Noise Gate vs. RGATE
0
–10
–20
–30
–40
–50
–60
–70
–80
1
T
= 25°C
COMPRESSION RATIO 10:1
A
V+ = 3V
V
= 24.5mV rms
IN
COMPRESSION RATIO 1:1
ROTATION POINT = 63mV rms
NOISE GATE SETTING = 1.4V rms
COMPRESSION RATIO 5:1
COMPRESSION RATIO 2:1
COMPRESSION RATIO 1:1
0.1
T
= 25°C
A
V+ = 3V
= 100kΩ
R
LOAD
ROTATION POINT = 63mV rms
NOISE GATE SETTING = 1.4V rms
0.01
–80
–70
–60
–50
–40
–30
–20
–10
20
100
1k
10k
30k
INPUT (dBV)
FREQUENCY (Hz)
Figure 7. Output vs. Input Characteristics
Figure 4. THD + N vs. Frequency
–10
–20
–30
–40
–50
–60
–70
–80
35
30
25
20
15
10
5
V+ = 3V + 0.1
R
R
= 5kΩ
= 0V
GATE
COMP
0
–5
–10
–15
V
R
= 2mV rms
IN
= 175kΩ
COMP
ROTATION POINT = 63mV rms
NOISE GATE SETTING = 1.4V rms
10
100
1k
10k
100k
1k
10k
100k
1M
10M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 8. PSRR vs. Frequency
Figure 5. GBW Curves vs. VCA Gain
Rev. C | Page 5 of 12
SSM2167
T
= 25°C
T = 25°C
A
A
C
= 10µF
C
= 10µF
SYS
SYSTEM GAIN = 19dB
= 100kΩ
SYS
SYSTEM GAIN = 8dB
R = 100kΩ
LOAD
R
LOAD
COMPRESSION RATIO 1:1
COMPRESSION RATIO 1:1
TIME (10µs/DIV)
TIME (10µs/DIV)
Figure 9. Small Signal Transient Response
Figure 11. Small Signal Transient Response
T
C
= 25°C
= 10µF
T
C
= 25°C
= 10µF
A
A
SYS
SYSTEM GAIN = 8.6dB
= 100kΩ
SYS
SYSTEM GAIN = 2.6dB
= 100kΩ
R
R
LOAD
LOAD
COMPRESSION RATIO 1:1
COMPRESSION RATIO 1:1
TIME (10µs/DIV)
TIME (10µs/DIV)
Figure 10. Large Signal Transient Response
Figure 12. Large Signal Transient Response
Rev. C | Page 6 of 12
SSM2167
–6dBV
–6dBV
–66dBV
–85dBV
–66dBV
–85dBV
TIME (1s/DIV)
TIME (500ms/DIV)
Figure 13. RMS Level Detector Performance with CAVG = 22 μF
Figure 15. RMS Level Detector Performance with CAVG = 2.2 μF
–6dBV
–66dBV
–85dBV
TIME (500ms/DIV)
Figure 14. RMS Level Detector Performance with CAVG = 2.2 μF
Rev. C | Page 7 of 12
SSM2167
APPLICATIONS INFORMATION
The SSM2167 is a complete microphone signal conditioning
system on a single integrated circuit. Designed primarily for
voice-band applications, this integrated circuit provides ampli-
fication, limiting, variable compression, and noise gate. User
adjustable compression ratio, noise gate threshold, and two
different fixed gains optimize circuit operation for a variety of
applications. The SSM2167 also features a low power shutdown
mode for battery-powered applications.
The breakpoint between the compression region and the limiting
region is referred to as the limiting threshold or the rotation point.
The term, rotation point, derives from the observation that the
straight line in the compression region rotates about this point on
the input/output characteristic as the compression ratio is changed.
The gain of the system with an input signal level of VRP is the fixed
gain, 18 dBV for the SSM2167, regardless of the compression ratio.
Input signals below VDE are downward expanded; that is, a −1 dB
change in the input signal level causes approximately a −3 dB
change in the output level. As a result, the gain of the system is
small for very small input signal levels, even though it may be
quite large for small input signals above VDE. The external resistor
at Pin 7, RGATE, is used to set the downward expansion
threshold (VDE).
V
DD
+
10µF
10
1
2
4
3
9
OUTPUT
100kΩ
10µF
V
GND
DD
SSM2167
10µF
R
GATE
Finally, the SSM2167 provides an active low, CMOS-compatible
digital power-down feature that reduces device supply current
to typically less than 2 μA.
7
8
V
DD
R
COMP
500kΩ
SHUTDOWN
INPUT
SIGNAL PATH
5
6
+
Figure 17 illustrates the block diagram of the SSM2167. The
audio input signal is processed by the input buffer and then by
the VCA. The input buffer presents an input impedance of
approximately 100 kΩ to the source. A dc voltage of approximately
1.5 V is present at INPUT (Pin 5) of the SSM2167, requiring the
use of a blocking capacitor (C1) for ground-referenced sources.
A 0.1 μF capacitor is a good choice for most audio applications.
The input buffer is a unity-gain stable amplifier that can drive
the low impedance input of the VCA and an internal rms detector.
10µF
0.1µF
GND
Figure 16. Typical Application Circuit
C2
10µF
V
DD
BUF
VCA
OUT
IN
1kΩ
1kΩ
The VCA is a low distortion, variable gain amplifier whose gain
is set by the side-chain control circuitry. An external blocking
capacitor (C2) must be used between the buffer output and the
VCA input. The 1 kΩ impedance between amplifiers determines
the value of this capacitor, which is typically between 4.7 μF and
10 μF. An aluminum electrolytic capacitor is an economical choice.
The VCA amplifies the input signal current flowing through C2
and converts this current to a voltage at the output pin (Pin 9) of
the SSM2167. The net gain from input to output can be as high
as 40 dB, depending on the gain set by the control circuitry.
INPUT
+1
VCA
OUTPUT
C1
0.1µF
BUFFER
NOISE GATE AND
COMPRESSION
SETTINGS
LEVEL
DETECTOR
CONTROL
C
AVG
C3
V
+
DD
R
R
C
G
10µF
SHUTDOWN GND
Figure 17. Functional Block Diagram
The output impedance of the SSM2167 is typically less than
145 Ω, and the external load on Pin 9 should be >5 kΩ. The
nominal output dc voltage of the device is approximately 1.4 V;
therefore, a blocking capacitor for grounded loads must be used.
THEORY OF OPERATION
The typical transfer characteristic for the SSM2167 is shown in
Figure 2 where the output level in dB is plotted as a function of
the input level in dB. The dotted line indicates the transfer char-
acteristic for a unity-gain amplifier. For input signals in the range
of VDE (downward expansion) to VRP (rotation point), an “r” dB
change in the input level causes a 1 dB change in the output level.
Here, r is defined as the compression ratio. The compression ratio
may be varied from 1:1 (no compression) to 10:1 via a single
resistor, RCOMP. Input signals above VRP are compressed with a
fixed compression ratio of approximately 10:1. This region of
operation is the limiting region. Varying the compression ratio has
no effect on the limiting region.
The bandwidth of the SSM2167 is quite wide at all gain settings.
The upper 3 dB point is over 1 MHz at gains as high as 30 dB.
The GBW plots are shown in Figure 5. The lower 3 dB cutoff
frequency of the SSM2167 is set by the input impedance of the
VCA (1 kΩ) and C2. Whereas the noise of the input buffer is
fixed, the input-referred noise of the VCA is a function of gain.
The VCA input noise is designed to be at a minimum when the
gain is at a maximum, thereby maximizing the usable dynamic
range of the part.
Rev. C | Page 8 of 12
SSM2167
LEVEL DETECTOR
15:1
5:1
The SSM2167 incorporates a full-wave rectifier and a true rms
level detector circuit whose averaging time constant is set by an
external capacitor (CAVG) connected to the AVG CAP (Pin 6).
For optimal low frequency operation of the level detector down
to 10 Hz, the value of the capacitor should be 2.2 μF. Some experi-
mentation with larger values for CAVG may be necessary to reduce
the effects of excessive low frequency ambient background noise.
The value of the averaging capacitor affects sound quality: too
small a value for this capacitor may cause a pumping effect for
some signals, whereas too large a value can result in slow response
times to signal dynamics. Electrolytic capacitors are recommended
here for lowest cost and should be in the range of 2 μF to 22 μF.
VCA GAIN
2:1
1:1
1
1
V
V
RP
DE
INPUT (dB)
The rms detector filter time constant is approximately given by
10 × CAVG milliseconds where CAVG is in μF. This time constant
controls both the steady state averaging in the rms detector as
well as the release time for compression; that is, the time it takes
for the system gain to increase due to a decrease in input signal.
The attack time, the time it takes for the gain to be reduced
because of a sudden increase in input level, is controlled mainly
by internal circuitry that speeds up the attack for large level
changes. In most cases, this limits overload time to less than 1 ms.
Figure 18. Effect of Varying the Compression Ratio
SETTING THE COMPRESSION RATIO
Changing the scaling of the control signal fed to the VCA causes
a change in the circuit compression ratio, r. This effect is shown
in Figure 18. Connecting a resistor (RCOMP) between Pin 8 and
V
DD sets the compression ratio. Lowering RCOMP gives smaller
compression ratios as indicated in Table 4. AGC performance is
achieved with compression ratios between 2:1 and 10:1, and is
dependent on the application. Shorting RCOMP disables the AGC
function, setting the compression equal to 1:1. If using a compres-
sion resistor, using a value greater than 5 kΩ is recommended.
If lower than 5 kΩ is used, the device may interpret this as a
short, 0 Ω.
The performance of the rms level detector is illustrated in
Figure 14 for a CAVG of 2.2 μF and Figure 13 for a CAVG of 22 μF.
In Figure 13, Figure 14, and Figure 15, the input signal to the
SSM2167 (not shown) is a series of tone bursts in six successive
10 dB steps. The tone bursts range from −66 dBV (0.5 mV rms)
to −6 dBV (0.5 V rms). As illustrated in these figures, the attack
time of the rms level detector is dependent only on CAVG, but the
release times are linear ramps whose decay times are dependent
on both CAVG and the input signal step size. The rate of release is
approximately 240 dB/s for a CAVG of 2.2 μF, and 12 dB/s for a
Table 4. Setting Compression Ratio
Compression Ratio
Value of RCOMP
0 Ω (short to V+)
15 kΩ
1:1
2:1
3:1
5:1
10:1
35 kΩ
75 kΩ
175 kΩ
CAVG of 22 μF.
CONTROL CIRCUITRY
The output of the rms level detector is a signal proportional to
the log of the true rms value of the buffer output with an added
dc offset. The control circuitry subtracts a dc voltage from this
signal, scales it, and sends the result to the VCA to control the
gain. The gain control of the VCA is logarithmic—a linear change
in control signal causes a dB change in gain. It is this control
law that allows linear processing of the log rms signal to provide
the flat compression characteristic on the input/output charac-
teristic shown in Figure 2.
Rev. C | Page 9 of 12
SSM2167
ROTATION POINT (LIMITING)
SETTING THE NOISE GATE THRESHOLD
(DOWNWARD EXPANSION)
Input signals above a particular level, the rotation point, are
attenuated (limited) by internal circuitry. This feature allows the
SSM2167 to limit the maximum output, preventing clipping of
the following stage, such as a codec or ADC. The rotation point
for SSM2167 is set internally to −24 dBV (63 mV rms).
The noise gate threshold is a programmable point using an external
resistor (RGATE) that is connected between Pin 7 (GATE THRS)
and VDD. The downward expansion threshold may be set between
−40 dBV and −55 dBV, as shown in Table 5. The downward
expansion threshold is inversely proportional to the value of this
resistance: setting this resistance to 0 Ω sets the threshold at
approximately 10 mV rms (−40 dBV), whereas a 5 kΩ resistance
sets the threshold at approximately 1 mV rms (−55 dBV). This
relationship is illustrated in Figure 19. It is not recommended to
use more than 5 kΩ for the RGATE resistor because the noise floor
of the SSM2167 prevents the noise gate from being lowered
further without causing problems.
SHUTDOWN FEATURE
The supply current of the SSM2167 can be reduced to under
10 μA by applying an active low, 0 V CMOS-compatible input
SHUTDOWN
to the
pin (Pin 3) of the SSM2167. In this state,
the input and output circuitry of the SSM2167 assumes a high
impedance state; as such, the potentials at the input pin and the
output pin are determined by the external circuitry connected
to the SSM2167. The SSM2167 takes approximately 200 ms to
settle from a shutdown to power-on command. For power-on to
shutdown, the SSM2167 requires more time, typically less than
1 sec. Cycling the power supply to the SSM2167 can result in
quicker settling times: the off-to-on settling time of the SSM2167 is
less than 200 ms, whereas the on-to-off settling time is less than
1 ms. The SSM2167 shutdown current is related to both temper-
ature and voltage.
Table 5. Setting Noise Gate Threshold
Noise Gate (dBV)
Value of RGATE
0 Ω (short to V+)
1 kΩ
2 kΩ
5 kΩ
−40
−48
−54
−55
PCB LAYOUT CONSIDERATIONS
Because the SSM2167 is capable of wide bandwidth operation
and can be configured for as much as 60 dB of gain, special care
must be exercised in the layout of the PCB that contains the IC
and its associated components. The following applications hints
should be considered for the PCB.
r:1
VCA GAIN
The layout should minimize possible capacitive feedback from
the output of the SSM2167 back to its input. Do not run input
and output traces adjacent to each other.
1
A single-point (star) ground implementation is recommended
in addition to maintaining short lead lengths and PCB runs. In
applications where an analog ground and a digital ground are
available, the SSM2167 and its surrounding circuitry should be
connected to the analog ground of the system. As a result of
these recommendations, wire-wrap board connections and
grounding implementations are to be explicitly avoided.
1
V
V
RP
DE2
V
V
INPUT (dB)
DE1
DE3
Figure 19. Effects of Varying the Downward
Expansion (Noise Gate) Threshold
Rev. C | Page 10 of 12
SSM2167
OUTLINE DIMENSIONS
3.10
3.00
2.90
6
10
5.15
4.90
4.65
3.10
3.00
2.90
1
5
PIN 1
0.50 BSC
0.95
0.85
0.75
1.10 MAX
0.80
0.60
0.40
8°
0°
0.15
0.05
0.33
0.17
SEATING
PLANE
0.23
0.08
COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-187-BA
Figure 20. 10-Lead Mini Small Outline Package [MSOP]
(RM-10)
Dimensions shown in millimeters
ORDERING GUIDE
Model
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
10-Lead MSOP
Package Option
Branding
SSM2167-1RM-REEL
SSM2167-1RM-R2
SSM2167-1RMZ-REEL1
SSM2167-1RMZ-R21
SSM2167-EVAL
RM-10
RM-10
RM-10
RM-10
B11
B11
B11#
B11#
Evaluation Board
1 Z = RoHS Compliant Part, # denotes RoHS compliant product may be top or bottom marked.
Rev. C | Page 11 of 12
SSM2167
NOTES
©2001–2007 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D02628-0-11/07(C)
Rev. C | Page 12 of 12
相关型号：
SSM2210SZ
TRANSISTOR 20 mA, 40 V, 2 CHANNEL, NPN, Si, SMALL SIGNAL TRANSISTOR, MS-012AA, PLASTIC, SOIC-8, BIP General Purpose Small Signal
ADI
SSM2210SZ-REEL
TRANSISTOR 20 mA, 40 V, 2 CHANNEL, NPN, Si, SMALL SIGNAL TRANSISTOR, MS-012AA, PLASTIC, SOIC-8, BIP General Purpose Small Signal
ADI
©2020 ICPDF网 联系我们和版权申明