AMS2026_05 [ADMOS]
DUAL POWER DISTRIBUTION SWITCH; 双电源分配开关
| 型号： | AMS2026_05 |
| 厂家： | 
ADVANCED MONOLITHIC SYSTEMS |
| 描述： | DUAL POWER DISTRIBUTION SWITCH |
| 文件： | 总5页 (文件大小：53K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Advanced
Monolithic
Systems
AMS2026
DUAL POWER DISTRIBUTION SWITCH
RoHS compliant
FEATURES
• 110mΩ Typ. (5V Input) High Side MOSFET Switch
• Short Circuit Protection
• Overcurrent Protection
• 100µA Maximum On-State Supply Current
• Available Active-High or Active-Low Enable
• Available in Space Saving 8 lead SOIC and 8 lead PDIP
• Thermal Protection
• Enable Input Compatible With 3V and 5V Logic
• Controlled Rise and Fall Times Limit Current
Surges and Minimize EMI
• Undervoltage Lock-Out Guarantees the Switch is
Off At Start-up
APPLICATIONS
• USB Power Management
• Hot Plug-In Power Supplies
• Battery-Charger Circuits
PRODUCT DESCRIPTION
The AMS2026 is a dual power distribution switch intended for applications where heavy capacitive loads and short-circuits are
likely to be encountered. The high-side switch is a 110mΩ N-channel MOSFET. The switch is controlled by a logic enable
input compatible with 3V and 5V logic and is available in active-high or active-low enable. The internal charge pump,
designed to control the power switch rise and fall time to minimize current surges during switching, also provides the gate
drive. Requiring no external components the charge pump allows operation from supplies as low as 3.3V. When an overload
or a short circuit is encountered the AMS2026 limits the output current to a safe level by switching into a constant-current
mode and the overcurrent logic output error flag is set to a low. Continuous heavy overloads and short circuits will increase the
power dissipation in the switch; this will cause the junction temperature to rise. The thermal protection circuit shuts the power
switch off to prevent damage. Once the device has cooled sufficiently, it will turn on automatic. An under voltage lock-out is
provided to insure that the power switch is in the Off state at start-up.
The AMS2026 is offered in the 8 lead SOIC package and the 8 lead PDIP package.
ORDERING INFORMATION
PACKAGE TYPE
PIN CONNECTIONS
8 LEAD SOIC/ 8 LEAD PDIP
OPER. TEMP
RANGE
8 LEAD SOIC
AMS2026S
8 LEAD PDIP
AMS2026P
ENABLE
ERROR
ERROR
ENABLE
1
2
3
4
8
7
6
5
OUTPUT
INPUT
-40°C to 85°C
GROUND
OUTPUT
Top View
Advanced Monolithic Systems, Inc. www.advanced-monolithic.com Phone (925) 443-0722 Fax (925) 443-0723
AMS2026
ABSOLUTE MAXIMUM RATINGS (Note 1)
Input Voltage Range, VI
Output Voltage Range, VO
-0.3V to 7V
-0.3V to VI(IN)
+0.3V
Internal Power Dissipation
Maximum Junction Temperature
(Note 3)
+125°C
Input Voltage Range, VI at /EN
Continuos Output Current, IO
-0.3V to 7V
Internally Limited
Storage Temperature
Lead Temperature (Soldering 25 sec)
-65°C to +150°C
265°C
ELECTRICAL CHARACTERISTICS
Electrical Characteristics for each section at TJ=25°C, VI(IN) = 5.5V, IO =rated current, /EN = 0V unless otherwise specified.
AMS2026
PARAMETER
CONDITIONS
Units
Min.
Max.
(Note 2)
Typ.
Switch On-State Resistance
VI(IN) = 5.5V
VI(IN) = 5.0V
VI(IN) = 4.5V
VI(IN) = 4.0V
/EN = VI
110
140
mΩ
mΩ
mΩ
mΩ
µA
µA
ms
110
110
110
0.01
140
140
140
5
Switch Output Leakage Current
Switch Output Rise Time
Switch Output Fall Time
10
/EN = VI , -40°C ≤ TJ ≤ 85°C
VI(IN) = 5.5V, CL = 1µF
VI(IN) = 2.7V, CL = 1µF
VI(IN) = 5.5V, CL = 1µF
VI(IN) = 2.7V, CL = 1µF
4.0V ≤ VI ≤ 5.5V
4.0
3.8
3.9
3.5
ms
ms
ms
Enable High-Level Input
Voltage
2.4
-1
V
Enable Low-Level Input Voltage
0.6
1
V
4.0V ≤ VI ≤ 5.5V
Enable Input Current
/EN = 0V or /EN = VI
µA
Enable Delay Time, Low-to-
High Output
20
40
ms
ms
CL = 1µF
CL = 1µF
Short Circuit Current
VI(IN) = 5.5V, TJ=25°C
0.66
1.2
1.8
A
OUT Connected to GND, device enable into
short circuit
Supply Current, Low-Level
Output
/EN = VI , TJ=25°C
0.015
73
10
10
µA
µA
µA
µA
V
/EN = VI , -40°C ≤ TJ ≤ 85°C
/EN = 0V, TJ=25°C
Supply Current, High-Level
Output
100
100
/EN = 0V, -40°C ≤ TJ ≤ 85°C
Undervoltage lock-out Low-
Level Input Voltage
2.0
3.0
3.2
Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. For guaranteed performance limits and associated test
conditions, see the Electrical Characteristics tables.
Note 2: To ensure constant junction temperature, low duty cycle pulse testing is used; thermal effects must be taken in consideration separately.
Note 3: The Power Dissipation for the SO-8 package is 725mW at TA = 25 °C. Above TA = 25 °C the Power Dissipation must be derated at 5.8mW/ °C (for TA
= 70 °C PD = 464mW ; for TA = 125 °C PD = 145mW)
RECOMMENDED OPERATING CONDITIONS:
Min
4.0V
0V
0A
-40°C
Max
5.5V
5.5V
0.6A
+125°C
Input Voltage, VI
Input Voltage, VI at /EN
Continuous Output Current, IO
Operating Junction Temp. Range
Advanced Monolithic Systems, Inc. www.advanced-monolithic.com Phone (925) 443-0722 Fax (925) 443-0723
AMS2026
PIN FUNCTIONS
Pin Name
Pin No.
I / O
Description
Enable
Ground
Input
Error Flag ERROR (A/B)
Output OUT(A/B)
/EN (A/B)
GND
IN
1/4
6
7
2/3
6-8
I
I
I
O
O
Enable Input, Logic turns power switch on.
Ground.
Power switch input, also supplies IC’s internal circuitry.
Overcurrent, Over temperature, Logic output.
Power switch output.
BLOCK DIAGRAM
POWER SWITCH
POWER SWITCH
IN
*
*
OUT A
OUT B
CS
CS
1.2V
REFERENCE
CURRENT
LIMIT
GATE
DRIVER
GATE
DRIVER
CURRENT
LIMIT
THERMAL
SENSE
ENABLE A
ERROR A
ENABLE B
ERROR B
ERROR
FLAG
CHARGE
PUMP
CHARGE
PUMP
ERROR
FLAG
UVLO
UVLO
GND
*Current Sense
FUNCTIONAL DESCRIPTION
Power Switch
Error Flag
The power switch is an N-channel MOSFET with a maximum on-
state resistance of 140mΩ (VI(IN) = 5.0V, configured as a high-side
switch.
The error flag output, is an open drain logic output that is active
low when output current exceeds current limit. Until the fault
condition is removed the output will remain active low.
Current Limit
Charge Pump
A sense FET monitors the current supplied to the load. In case of
an overload or short circuit, the current limit circuitry sends a
signal to the driver. The driver will then reduce the gate voltage
and drive the power FET into its linear region, which switches the
output into a constant current mode and holds the current constant
while varying the voltage on the load.
An internal 100kHz charge pump supplies the power to the driver
circuit and provides the required voltage to pull the gate of the
MOSFET above the source. The charge pump requires very little
supply current and operates from input voltages as low as 3.0V.
Gate Driver
The driver controls the gate voltage of the power switch. The
driver incorporates circuitry that controls the rise and fall times of
the output voltage, as a result it limits large current surges and
reduces the associated electromagnetic interference (EMI)
produced. The rise and fall times of the output voltage are
typically in the 2ms to 4ms range instead of the microsecond or
nanosecond range for a standard FET.
Thermal Shutdown
The internal thermal shutdown circuit will shut the power switch
off when the junction temperature rises to approx. 180°C.
Hysteresis is build into the thermal sense circuitry, and after the
junction temperature has dropped about 20°C, the switch turns
back on. Until the fault is removed the switch will continue to
cycle off and on.
Enable
Undervoltage Lock-out
A logic high on the /EN input turns off the power switch and the
bias for the charge pump, driver, and other circuitry to reduce the
supply current to less than 10µA. A logic zero input restore bias to
the drive and control circuits and turns the power on. The enable
input is compatible with both TTL and CMOS logic levels.
An internal voltage sense monitors the input voltage. When the
input voltage is below 3.2V nominal, the switch is turned off by a
control signal. The typical fall time range due to the sense of a
low voltage is 250µs to 750µs.
Advanced Monolithic Systems, Inc. www.advanced-monolithic.com Phone (925) 443-0722 Fax (925) 443-0723
AMS2026
APPLICATION HINTS
Power Supply Considerations
As an initial estimate use the highest operating ambient
temperature of interest and read rON from Figure 1. Power
dissipation is equal to:
A 0.047µF ceramic bypass capacitor close to the device, between
input and ground is recommended. When the output load is heavy
or has large paralleled capacitors, a high value electrolytic capacitor
should be used. To improve the immunity of the device to ESD, use
a 0.1µF ceramic capacitor to bypass the output.
PD = rON x I2
Calculate the junction temperature:
TJ = PD x RθJA + TA
Where RθJA is the thermal resistance and is 172°C/W for the
SOIC package. Compare the calculated junction temperature
with the initial estimate and if they don’t mach within a few
degrees, repeat the calculations using the calculated value as the
new estimate. A few repetitions will be sufficient to give a
reasonable answer.
Current Limit
A sense FET monitors overcurrent conditions. When an overcurrent
condition is detected the device maintains a constant output current
and decreases the voltage accordingly. If the condition is present
long enough to activate the thermal limiting the result is the
shutdown of the device.
Thermal Protection
There are three situation in which overload can occur. In the first
case, the output has been shorted before the device is enabled or
before VI has been applied. The device senses the short and
switches into a constant-current output.
In the second case, the short occurs while the device is enabled.
When this happens, very high currents flow for a short time before
the current-limit circuit can react. After the current-limit circuit has
tripped, the device limits normally.
In the third case, the load has been gradually increased beyond the
recommended operating current. The current will rise until the
current-limit threshold is reached. The AMS2026 is able to deliver
current up to the current-limit threshold without damage. When the
threshold has been reached the device switches into the constant
current mode. When over current condition is detected the error flag
logic output remains low until the condition is removed.
Thermal protection prevents damage to the device when over
load or short circuits conditions are present for extended periods
of time. These conditions force the AMS2026 into the constant
current mode. As a result the voltage across the high-side switch
will increase. Under short-circuit conditions the voltage across
the switch is equal to the input voltage. Continuous short circuits
and heavy over loads increase the power dissipation in the switch
and causes the junction temperature to rise to dangerously high
levels. The protection circuit shuts off the switch when it senses
the high junction temperature. The switch remains off until the
device has cooled about 20°C. The switch continues to cycle off
and on until the fault is removed.
Undervoltage Lock-out
Power Dissipation and Junction Temperature
An undervoltage lock-out is provided to insure that the switch is
in the off state at start-up. When the input voltage falls below
3.0V the switch will be turned off immediately. This will make it
easy for designers of hot plug-in systems that may not be able to
turn the switch off before removing the input power. In such
cases when the device is reinserted, the turn on will have a
controlled rise time to reduce EMI and voltage overshoots.
The thermal resistance of the surface-mount packages such as SOIC
is high compared to that of power packages. The use of the N-
cannel MOSFET which has low on-resistance, makes it possible for
small surface-mount packages to pass large currents. To determine
the power dissipation and junction temperature the first step is to
find rON at the input voltage and operating temperature.
EXTERNAL LOAD A
7
8
5
POWER SUPPLY
4.0V - 5.0V
TYPICAL APPLICATIONS
IN
OUT A
1µF
0.1
µF
0.1
µ
F
10k
10k
2
3
1
4
ERROR A
ERROR B
EN
ERROR FLAG A
ERROR FLAG B
ENABLE A
EXTERNAL LOAD B
OUT B
EN
ENABLE B
GND
0.1µ
F
6
Figure 1
Advanced Monolithic Systems, Inc. www.advanced-monolithic.com Phone (925) 443-0722 Fax (925) 443-0723
AMS2026
PACKAGE DIMENSIONS inches (millimeters) unless otherwise noted.
8 LEAD SOIC PLASTIC PACKAGE (S)
0.189-0.197*
(4.801-5.004)
8
7
6
5
0.228-0.244
(5.791-6.197)
0.150-0.157**
(3.810-3.988)
1
2
3
4
0.010-0.020
(0.254-0.508)
x 45°
0.053-0.069
(1.346-1.752)
0.004-0.010
(0.101-0.254)
0.008-0.010
(0.203-0.254)
0°-8° TYP
0.014-0.019
(0.355-0.483)
0.050
(1.270)
TYP
0.016-0.050
(0.406-1.270)
S (SO-8 ) AMS DRW# 042293
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
8 LEAD PLASTIC DIP PACKAGE (P)
0.400*
(10.160)
MAX
8
7
6
5
0.255±0.015*
(6.477±0.381)
1
2
3
4
0.300-0.325
(7.620-8.255)
0.130±0.005
(3.302±0.127)
0.045-0.065
(1.143-1.651)
0.065
(1.651)
TYP
0.009-0.015
0.125
(3.175)
MIN
(0.229-0.381)
0.005
(0.127)
MIN
0.015
(0.380)
MIN
+0.025
-0.015
+0.635
0.325
0.100±0.010
(2.540±0.254)
0.018±0.003
(0.457±0.076)
(
8.255
)
-0.381
P (8L PDIP ) AMS DRW# 042294
*DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTUSIONS.
MOLD FLASH OR PROTUSIONS SHALL NOT EXCEED 0.010" (0.254mm)
Advanced Monolithic Systems, Inc. www.advanced-monolithic.com Phone (925) 443-0722 Fax (925) 443-0723
相关型号：
©2020 ICPDF网 联系我们和版权申明