AD1585B
更新时间:2024-09-18 02:20:35
品牌:ADI
描述:2.5 V to 5.0 V Micropower, Precision Series Mode Voltage References
AD1585B 概述
2.5 V to 5.0 V Micropower, Precision Series Mode Voltage References 2.5 V至5.0 V微功耗,精密串联模式电压基准
AD1585B 数据手册
通过下载AD1585B数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载2.5 V to 5.0 V Micropower, Precision
Series Mode Voltage References
a
AD1582/AD1583/AD1584/AD1585
FUNCTIONAL BLOCK DIAGRAM
3-Lead SOT-23
FEATURES
Series Reference (2.5 V, 3 V, 4.096 V, 5 V)
Low Quiescent Current: 70 ꢀA max
Current Output Capability: ꢁ5 mA
(RT Suffix)
Wide Supply Range: VIN = VOUT + 200 mV to 12 V
Wideband Noise (10 Hz to 10 kHz): 50 ꢀV rms
Specified Temperature Range: –40ꢂC to +125ꢂC
Compact, Surface-Mount SOT-23 Package
1
2
V
OUT
AD1582/
AD1583/
AD1584/
AD1585
3
V
IN
TOP VIEW
GND
AD158x Products, Three Electrical Grades
Electrical
Grade
Tempco
(ppmꢂC)
Initial Accuracy
AD1582 AD1583/AD1585 AD1584
TARGET APPLICATIONS
1. Portable, battery-powered equipment, e.g., notebook comput-
ers, cellular phones, pagers, PDAs, GPSs, and DMMs.
B
C
A
0.08%
0.16%
0.80%
0.10%
0.20%
1.00%
0.10%
0.20%
0.98%
50
50
100
2. Computer workstations. Suitable for use with a wide range of
video RAMDACs.
GENERAL DESCRIPTION
The AD1582, AD1583, AD1584, and AD1585 are a family of low
cost, low power, low dropout, precision band gap references.
These designs are available as three-terminal (series) devices
and are packaged in the compact SOT-23, 3-lead surface-mount
package. The versatility of these references makes them ideal for
use in battery-powered 3 V or 5 V systems where there may be
wide variations in supply voltage and a need to minimize power
dissipation.
3. Smart industrial transmitters
4. PCMCIA cards
5. Automotive
6. Hard disk drives
7. 3 V/5 V, 8-bit/12-bit data converters
900
800
700
600
The superior accuracy and temperature stability of the AD1582/
AD1583/AD1584/AD1585 is made possible by the precise
matching and thermal tracking of on-chip components. Patented
temperature drift curvature correction design techniques minimize
the nonlinearities in the voltage output temperature characteristic.
*
SHUNT REFERENCE
500
400
These series mode devices (AD1582/AD1583/AD1584/AD1585)
source or sink up to 5 mA of load current and operate efficiently
with only 200 mV of required headroom supply. This family
draws a maximum 70 µA of quiescent current with only a 1.0 µA/V
variation with supply voltage. The advantage of these designs
over conventional shunt devices is extraordinary. Valuable supply
current is no longer wasted through an input series resistor, and
maximum power efficiency is achieved at all input voltage levels.
300
200
100
AD1582 SERIES REFERENCE
0
2.7
5
V
(V)
SUPPLY
*
3.076kꢃ SOURCE RESISTOR
The AD1582, AD1583, AD1584, and AD1585 are available in
three grades, A, B, and C, and are provided in a tiny footprint,
the SOT-23. All grades are specified over the industrial tem-
perature range of –40°C to +125°C.
Figure 1. Supply Current (µA) vs. Supply Voltage (V)
REV. D
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, norforanyinfringementsofpatentsorotherrightsofthirdpartiesthat
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
Fax: 781/326-8703
www.analog.com
© 2004 Analog Devices, Inc. All rights reserved.
AD1582/AD1583/AD1584/AD1585
AD1582–SPECIFICATIONS
(@ TA = TMIN to TMAX, VIN = 5 V, unless otherwise noted.)
AD1582A
Typ
AD1582B
Typ
AD1582C
Typ Max Unit
Parameter
Min
Max Min
Max Min
OUTPUT VOLTAGE (@ 25°C)
VO
2.480 2.500 2.520 2.498 2.500 2.502 2.496 2.500 2.504
V
INITIAL ACCURACY ERROR (@ 25°C)
VOERR
–20
–0.80
+20
+0.80 –0.08
–2
+2
–4
+4
+0.16
mV
%
+0.08 –0.16
OUTPUT VOLTAGE TEMPERATURE DRIFT
100
50
50
50
ppm/°C
TEMPERATURE COEFFICIENT (TCVO)
–40°C < TA < +125°C
0°C < TA < 70°C
40
35
100
18
15
50
18
15
ppm/°C
ppm/°C
MINIMUM SUPPLY HEADROOM (VIN–VOUT
)
200
200
200
mV
LOAD REGULATION
0 mA < IOUT < 5 mA (–40°C to +85°C)
0 mA < IOUT < 5 mA (–40°C to +125°C)
–5 mA < IOUT < 0 mA (–40°C to +85°C)
–5 mA < IOUT < 0 mA (–40°C to +125°C)
–0.1 mA < IOUT < +0.1 mA (–40°C to +85°C)
0.2
0.4
0.25
0.45
2.7
0.2
0.4
0.25
0.45
2.7
0.2
0.4
0.25
0.45
2.7
mV/mA
mV/mA
mV/mA
mV/mA
mV/mA
mV/mA
–0.1 mA < IOUT < +0.1 mA (–40°C to +125°C)
3.5
3.5
3.5
LINE REGULATION
VOUT 200 mV < VIN < 12 V
IOUT = 0 mA
25
25
25
µV/V
RIPPLE REJECTION (∆VOUT/∆VIN
)
VIN = 5 V 100 mV (f = 120 Hz)
80
80
80
dB
µA
QUIESCENT CURRENT
70
15
70
15
70
15
SHORT-CIRCUIT CURRENT TO GROUND
mA
NOISE VOLTAGE (@ 25°C)
0.1 Hz to 10 Hz
10 Hz to 10 kHz
70
50
70
50
70
50
µV p-p
µV rms
TURN-ON SETTLING TIME TO 0.1%,
CL = 0.2 µF
100
100
100
µs
LONG-TERM STABILITY
1000 Hours @ 25°C
100
115
100
115
100
115
ppm/1000 hrs.
ppm
OUTPUT VOLTAGE HYSTERESIS
TEMPERATURE RANGE
Specified Performance (A, B, C)
Operating Performance (A, B, C)
–40
–55
+125 –40
+125 –55
+125 –40
+125 –55
+125 °C
+125 °C
Specifications subject to change without notice.
REV. D
–2–
AD1582/AD1583/AD1584/AD1585
(@ TA = TMIN to TMAX, VIN = 5 V, unless otherwise noted.)
AD1583–SPECIFICATIONS
AD1583A
Typ
AD1583B
Typ
AD1583C
Typ Max Unit
Parameter
Min
Max Min
Max Min
OUTPUT VOLTAGE (@ 25°C)
VO
2.970 3.000 3.030 2.997 3.000 3.003 2.994 3.000 3.006
V
INITIAL ACCURACY ERROR (@ 25°C)
VOERR
–30
–1.0
+30
+1.0
–3
–0.1
+3
+0.1
–6
–0.20
+6
+0.20
mV
%
OUTPUT VOLTAGE TEMPERATURE DRIFT
100
50
50
ppm/°C
TEMPERATURE COEFFICIENT (TCVO)
–40°C < TA < +125°C
0°C < TA < 70°C
40
35
100
18
15
50
18
15
50
ppm/°C
ppm/°C
MINIMUM SUPPLY HEADROOM (VIN–VOUT
)
200
200
200
mV
LOAD REGULATION
0 mA < IOUT < 5 mA (–40°C to +85°C)
0 mA < IOUT < 5 mA (–40°C to +125°C)
–5 mA < IOUT < 0 mA (–40°C to +85°C)
–5 mA < IOUT < 0 mA (–40°C to +125°C)
–0.1 mA < IOUT < +0.1 mA (–40°C to +85°C)
–0.1 mA < IOUT < +0.1 mA (–40°C to +125°C)
0.25
0.45
0.40
0.6
2.9
3.7
0.25
0.45
0.40
0.6
2.9
3.7
0.25
0.45
0.40
0.6
2.9
3.7
mV/mA
mV/mA
mV/mA
mV/mA
mV/mA
mV/mA
LINE REGULATION
VOUT 200 mV < VIN < 12 V
IOUT = 0 mA
25
25
25
µV/V
RIPPLE REJECTION (∆VOUT/∆VIN
)
VIN = 5 V 100 mV (f = 120 Hz)
80
80
80
dB
µA
QUIESCENT CURRENT
70
15
70
15
70
15
SHORT-CIRCUIT CURRENT TO GROUND
mA
NOISE VOLTAGE (@ 25°C)
0.1 Hz to 10 Hz
10 Hz to 10 kHz
85
60
85
60
85
60
µV p-p
µV rms
TURN-ON SETTLING TIME TO 0.1%
CL = 0.2 µF
120
120
120
µs
LONG-TERM STABILITY
1000 Hours @ 25°C
100
115
100
115
100
115
ppm/1000 hrs.
ppm
OUTPUT VOLTAGE HYSTERESIS
TEMPERATURE RANGE
Specified Performance (A, B, C)
Operating Performance (A, B, C)
–40
–55
+125 –40
+125 –55
+125 –40
+125 –55
+125 °C
+125 °C
Specifications subject to change without notice.
REV. D
–3–
AD1582/AD1583/AD1584/AD1585
AD1584–SPECIFICATIONS (@ TA = TMIN to TMAX, VIN = 5 V, unless otherwise noted.)
AD1584A
Typ
AD1584B
Typ
AD1584C
Typ Max Unit
Parameter
Min
Max Min
Max Min
OUTPUT VOLTAGE (@ 25°C)
VO
4.056 4.096 4.136 4.092 4.096 4.100 4.088 4.096 4.104
V
INITIAL ACCURACY ERROR (@ 25°C)
VOERR
–40
–0.98
+40
+0.98 –0.1
–4
+4
+0.1
–8
–0.2
+8
+0.2
mV
%
OUTPUT VOLTAGE TEMPERATURE DRIFT
100
50
50
ppm/°C
TEMPERATURE COEFFICIENT (TCVO)
–40°C < TA < +125°C
0°C < TA < 70°C
40
35
100
18
15
50
18
15
50
ppm/°C
ppm/°C
MINIMUM SUPPLY HEADROOM (VIN–VOUT
)
200
200
200
mV
LOAD REGULATION
0 mA < IOUT < 5 mA (–40°C to +85°C)
0 mA < IOUT < 5 mA (–40°C to +125°C)
–5 mA < IOUT < 0 mA (–40°C to +85°C)
–5 mA < IOUT < 0 mA (–40°C to +125°C)
–0.1 mA < IOUT < +0.1 mA (–40°C to +85°C)
–0.1 mA < IOUT < +0.1 mA (–40°C to +125°C)
0.32
0.52
0.40
0.6
3.2
4.1
0.32
0.52
0.40
0.6
3.2
4.1
0.32
0.52
0.40
0.6
3.2
4.1
mV/mA
mV/mA
mV/mA
mV/mA
mV/mA
mV/mA
LINE REGULATION
VOUT 200 mV < VIN < 12 V
IOUT = 0 mA
25
25
25
µV/V
RIPPLE REJECTION (∆VOUT/∆VIN
)
VIN = 5 V 100 mV (f = 120 Hz)
80
80
80
dB
µA
QUIESCENT CURRENT
70
15
70
15
70
15
SHORT-CIRCUIT CURRENT TO GROUND
mA
NOISE VOLTAGE (@ 25°C)
0.1 Hz to 10 Hz
10 Hz to 10 kHz
110
90
110
90
110
90
µV p-p
µV rms
TURN-ON SETTLING TIME TO 0.1%
CL = 0.2 µF
140
140
140
µs
LONG-TERM STABILITY
1000 Hours @ 25°C
100
115
100
115
100
115
ppm/1000 hrs.
ppm
OUTPUT VOLTAGE HYSTERESIS
TEMPERATURE RANGE
Specified Performance (A, B, C)
Operating Performance (A, B, C)
–40
–55
+125 –40
+125 –55
+125 –40
+125 –55
+125 °C
+125 °C
Specifications subject to change without notice.
REV. D
–4–
AD1582/AD1583/AD1584/AD1585
(@ TA = TMIN to TMAX, VIN = 6 V, unless otherwise noted.)
AD1585–SPECIFICATIONS
AD1585A
Typ
AD1585B
Typ
AD1585C
Typ Max Unit
Parameter
Min
Max Min
Max Min
OUTPUT VOLTAGE (@ 25°C)
VO
4.950 5.000 5.050 4.995 5.000 5.005 4.990 5.000 5.010
V
INITIAL ACCURACY ERROR (@ 25°C)
VOERR
–50
–1.0
+50
+1.0
–5
–0.10
+5
–10
+10
+0.20
mV
%
+0.10 –0.20
OUTPUT VOLTAGE TEMPERATURE DRIFT
100
50
50
ppm/°C
TEMPERATURE COEFFICIENT (TCVO)
–40°C < TA < +125°C
0°C < TA < 70°C
40
35
100
18
15
50
18
15
50
ppm/°C
ppm/°C
MINIMUM SUPPLY HEADROOM (VIN–VOUT
)
200
200
200
mV
LOAD REGULATION
0 mA < IOUT < 5 mA (–40°C to +85°C)
0 mA < IOUT < 5 mA (–40°C to +125°C)
–5 mA < IOUT < 0 mA (–40°C to +85°C)
–5 mA < IOUT < 0 mA (–40°C to +125°C)
–0.1 mA < IOUT < +0.1 mA (–40°C to +85°C)
–0.1 mA < IOUT < +0.1 mA (–40°C to +125°C)
0.40
0.6
0.40
0.6
4
0.40
0.6
0.40
0.6
4
0.40
0.6
0.40
0.6
4
mV/mA
mV/mA
mV/mA
mV/mA
mV/mA
mV/mA
4.8
4.8
4.8
LINE REGULATION
VOUT 200 mV < VIN < 12 V
IOUT = 0 mA
25
25
25
µV/V
RIPPLE REJECTION (∆VOUT/∆VIN
)
VIN = 6 V 100 mV (f = 120 Hz)
80
80
80
dB
µA
QUIESCENT CURRENT
70
15
70
15
70
15
SHORT-CIRCUIT CURRENT TO GROUND
mA
NOISE VOLTAGE (@ 25°C)
0.1 Hz to 10 Hz
10 Hz to 10 kHz
140
100
140
100
140
100
µV p-p
µV rms
TURN-ON SETTLING TIME TO 0.1%
CL = 0.2 µF
175
175
175
µs
LONG-TERM STABILITY
1000 Hours @ 25°C
100
115
100
115
100
115
ppm/1000 hrs.
ppm
OUTPUT VOLTAGE HYSTERESIS
TEMPERATURE RANGE
Specified Performance (A, B, C)
Operating Performance (A, B, C)
–40
–55
+125 –40
+125 –55
+125 –40
+125 –55
+125 °C
+125 °C
Specifications subject to change without notice.
REV. D
–5–
AD1582/AD1583/AD1584/AD1585
ABSOLUTE MAXIMUM RATINGS1
PACKAGE BRANDING INFORMATION
VIN to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 V
Four fields identify the device:
Internal Power Dissipation2
• First field, product identifier, for example, a “2/3/4/5” identifies
the generic as AD1582/AD1583/AD1584/AD1585
• Second field, device grade, which can be “A,” “B,” or “C”
• Third field, calendar year of processing, “7” for 1997...,
“A” for 2001...
SOT-23 (RT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400 mW
Storage Temperature Range . . . . . . . . . . . . –65°C to +125°C
Specified Temperature Range
AD1582RT/AD1583RT/,
AD1584RT/AD1585RT . . . . . . . . . . . . . –40°C to +125°C
• Fourth field, two-week window within the calendar year, for
example, letters A–Z to represent a two-week window starting
with “A” for the first two weeks of January.
Lead Temperature, Soldering
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . 215°C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220°C
NOTES
1Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2Specification is for device in free air at 25°C: SOT-23 package: θJA = 300°C/W.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD1582/AD1583/AD1584/AD1585 feature proprietary ESD protection circuitry,
permanent damage may occur on devices subjected to high energy electrostatic discharges.
Therefore, proper ESD precautions are recommended to avoid performance degradation or loss
of functionality.
WARNING!
ESD SENSITIVE DEVICE
ORDERING GUIDE
Initial
Output
Initial
Temperature
Voltage Accuracy Accuracy Coefficient
Package
Description Option
Package Top
Number of
Parts per Reel
Model
(V)
(mV)
(%)
(ppm/ꢂC)
Mark
AD1582ART-R2
AD1582ART-Reel7
AD1582BRT-R2
AD1582BRT-Reel7
AD1582CRT-Reel7
2.50
2.50
2.50
2.50
2.50
20
20
2
2
4
0.80
0.80
0.08
0.08
0.16
100
100
50
50
50
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
RT-3
RT-3
RT-3
RT-3
RT-3
2A0A
2A0A
2B0A
2B0A
2C0A
250
3000
250
3000
3000
AD1583ART-R2
AD1583ART-Reel7
AD1583BRT-R2
AD1583BRT-Reel7
AD1583CRT-Reel7
3.00
3.00
3.00
3.00
3.00
30
30
3
3
6
1.00
1.00
0.10
0.10
0.20
100
100
50
50
50
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
RT-3
RT-3
RT-3
RT-3
RT-3
3A0A
3A0A
3B0A
3B0A
3C0A
250
3000
250
3000
3000
AD1584ART-R2
AD1584ART-Reel7
AD1584BRT-R2
AD1584BRT-Reel7
AD1584CRT-Reel7
4.096
4.096
4.096
4.096
4.096
40
40
4
4
8
0.98
0.98
0.10
0.10
0.20
100
100
50
50
50
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
RT-3
RT-3
RT-3
RT-3
RT-3
4A0A
4A0A
4B0A
4B0A
4C0A
250
3000
250
3000
3000
AD1585ART-R2
AD1585ART-Reel7
AD1585BRT-R2
AD1585BRT-Reel7
AD1585CRT-R2
AD1585CRT-Reel7
5.00
5.00
5.00
5.00
5.00
5.00
50
50
5
5
10
10
1.00
1.00
0.10
0.10
0.20
0.20
100
100
50
50
50
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
5A0A
5A0A
5B0A
5B0A
5C0A
5C0A
250
3000
250
3000
250
3000
50
REV. D
–6–
AD1582/AD1583/AD1584/AD1585
PARAMETER DEFINITIONS
Temperature Coefficient (TCVO)
The change of output voltage over the operating temperature
change and normalized by the output voltage at 25ЊC, expressed
in ppm/ЊC. The equation follows:
Thermal Hysteresis (VO_HYS
)
The change of output voltage after the device is cycled through
temperatures from +25ЊC to –40ЊC to +85°C and back to +25ЊC.
This is a typical value from a sample of parts put through such
a cycle:
V T −V T
(
)
O( )
O
2
1
×106
VO_HYS = V 25°C −V
(
)
TCV ppm/°C ] =
O
O_TC
[
O
V 25°C × T − T
(
)
(
)
O
2
1
V 25°C −V
(
)
O
O_TC
×106
where:
VO_HYS ppm =
[
]
V 25°C
(
)
O
VO(25ЊC) = VO at 25ЊC
where:
VO(25ЊC) = VO at 25ЊC
O_TC = VO at 25ЊC after temperature cycle at +25ЊC to
VO(T1) = VO at temperature 1
VO(T2) = VO at temperature 2
V
–40ЊC to +85ЊC and back to +25ЊC
Line Regulation (∆VO/∆VIN
)
Operating Temperature
The change in output voltage due to a specified change in input
voltage. It includes the effects of self-heating. Line regulation is
expressed in either percent per volt, parts per million per volt, or
microvolts per volt change in input voltage.
The temperature extremes at which the device can still function.
Parts may deviate from their specified performance outside the
specified temperature range.
Load Regulation (∆VO/∆ILOAD
)
The change in output voltage due to a specified change in load
current. It includes the effects of self-heating. Load regulation is
expressed in either microvolts per milliampere, parts per million
per milliampere, or Ω of dc output resistance.
Long-Term Stability (∆VO)
Typical shift of output voltage at 25ЊC on a sample of parts
subjected to an operation life test of 1000 hours at 125ЊC:
∆V = V t −V t
O( 0 ) O( 1)
O
V t −V t
O( 0 ) O( 1)
∆V ppm =
×106
[
]
O
V t
O( 0 )
where:
VO(t0) = VO at 25ЊC at time 0
VO(t1) = VO at 25ЊC after 1000 hours operation at 125ЊC
REV. D
–7–
AD1582/AD1583/AD1584/AD1585–Typical Performance Characteristics
0.40
22
20
18
16
14
12
10
8
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0
AD1585
AD1582
6
4
2
0
0
2
4
6
8
10
12
–60 –50 –40 –30 –20 –10
0
10
20 30
50
40
ppm/ꢂC
V
(V)
IN
TPC 1. Typical Output Voltage Temperature Drift
Distribution
TPC 4. Load Regulation vs. VIN
50
45
40
35
30
25
20
15
10
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
AD1582
AD1585
5
0
–1.00%
–0.60%
–0.20%
V
0.20%
(ERROR)
0.60%
1.00%
–5
–4
–3
–2
–1
0
1
2
3
4
5
I
(mA)
OUT
OUT
TPC 2. Typical Output Voltage Error Distribution
TPC 5. Line Regulation vs. ILOAD
2.504
2.502
10k
2.500
2.498
2.496
I
= 1mA
OUT
I
= 0
OUT
1k
2.494
2.492
2.490
2.488
100
10
100k
100
1k
FREQUENCY (Hz)
10k
–40
–20
0
20
40
60
80
100
120
TEMPERATURE ( C)
TPC 3. Typical Temperature Drift Characteristic Curves
TPC 6. Noise Spectral Density
REV. D
–8–
AD1582/AD1583/AD1584/AD1585
THEORY OF OPERATION
The AD1582/AD1583/AD1584/AD1585 family uses the band gap
concept to produce stable, low temperature coefficient voltage
references suitable for high accuracy data acquisition components
and systems. This family of precision references uses the underlying
temperature characteristics of a silicon transistor’s base emitter
voltage in the forward-biased operating region. Under this
condition, all such transistors have a –2 mV/°C temperature
coefficient (TC) and a VBE that, when extrapolated to absolute
zero, 0°K (with collector current proportional to absolute
temperature), approximates the silicon band gap voltage. By
summing a voltage that has an equal and opposite temperature
coefficient of 2 mV/°C with the VBE of a forward-biased transistor,
an almost zero TC reference can be developed. In the AD1582/
AD1583/AD1584/AD1585 simplified circuit diagram shown in
Figure 2, such a compensating voltage, V1, is derived by
driving two transistors at different current densities and
amplifying the resultant VBE difference (∆VBE, which has a positive
TC). The sum of VBE and V1(VBG) is then buffered and ampli-
fied to produce stable reference voltage outputs of 2.5 V, 3 V,
4.096 V, and 5 V.
+
1
AD1582/
AD1583/
AD1584/
AD1585
V
V
3
IN
1ꢀF
OUT
4.7ꢀF
–
2
Figure 3. Typical Connection Diagram
TEMPERATURE PERFORMANCE
The AD1582/AD1583/AD1584/AD1585 family of references is
designed for applications where temperature performance is
important. Extensive temperature testing and characterization
ensures that the device’s performance is maintained over the
specified temperature range.
The error band guaranteed with the AD1582/AD1583/AD1584/
AD1585 family is the maximum deviation from the initial value at
25°C. Thus, for a given grade of the AD1582/AD1583/AD1584/
AD1585, the designer can easily determine the maximum total
error by summing initial accuracy and temperature variation,
e.g., for the AD1582BRT, the initial tolerance is 2 mV, the
temperature error band is 8 mV, thus the reference is guaranteed
to be 2.5 V 10 mV from –40°C to +125°C.
V
IN
R3
R4
Figure 4 shows the typical output voltage drift for the AD1582
and illustrates the methodology. The box in Figure 4 is bounded on
the x-axis by operating temperature extremes. It is bounded
on the y-axis by the maximum and minimum output voltages
observed over the operating temperature range. The slope of the
diagonal drawn from the initial output value at 25°C to the output
values at +125°C and –40°C determines the performance grade of
the device.
V
OUT
R5
V
BG
+
V
R2
–
BE
R6
+
V1
–
R1
Duplication of these results requires a test system that is highly
accurate with stable temperature control. Evaluation of the
AD1582 produces curves similar to those in TPC 3 and Figure 4,
but output readings may vary depending upon the test methods
and test equipment used.
GND
Figure 2. Simplified Schematic
APPLYING THE AD1582/AD1583/AD1584/AD1585
The AD1582/AD1583/AD1584/AD1585 is a family of series
references that can be used for many applications. To achieve
optimum performance with these references, only two external
components are required. Figure 3 shows the AD1582 configured
for operation under all loading conditions. With a simple 4.7 µF
capacitor attached to the input and a 1 µF capacitor applied
to the output, the devices can achieve specified performance for
all input voltage and output current requirements. For best
transient response, add a 0.1 µF capacitor in parallel with the 4.7 µF
capacitor. While a 1 µF output capacitor can provide stable
performance for all loading conditions, the AD1582 can operate
under low (–100 µA < I OUT < +100 µA) current conditions with
just a 0.2 µF output capacitor. The 4.7 µF capacitor on the input can
be reduced to 1 µF in this condition.
2.504
2.502
2.500
2.498
2.496
2.494
2.492
–40
–20
0
20
40
60
80
100
120
Unlike conventional shunt reference designs, the AD1582/
AD1583/AD1584/AD1585 family provides stable output voltages
at constant operating current levels. When properly decoupled,
as shown in Figure 3, these devices can be applied to any circuit
and provide superior low power solutions.
TEMPERATURE ( C)
Figure 4. Output Voltage vs. Temperature
REV. D
–9–
AD1582/AD1583/AD1584/AD1585
80
70
60
50
40
30
20
10
0
VOLTAGE OUTPUT NONLINEARITY VERSUS
TEMPERATURE
When using a voltage reference with data converters, it is impor-
tant to understand the impact that temperature drift can have on
the converter’s performance. The nonlinearity of the reference
output drift represents additional error that cannot easily be
calibrated out of the overall system. To better understand the
impact such a drift can have on a data converter, refer to Figure 5
where the measured drift characteristic is normalized to the
endpoint average drift. The residual drift error of the AD1582
of approximately 200 ppm demonstrates that this family of
references is compatible with systems that require 12-bit
accurate temperature performance.
–700
–450
–200
50
ppm
300
550
250
200
150
100
50
Figure 6. Output Voltage Hysteresis Distribution
SUPPLY CURRENT VERSUS TEMPERATURE
The quiescent current for the AD1582/AD1583/AD1584/AD1585
family of references varies slightly over temperature and input
supply range. Figure 7 demonstrates the typical performance
for the AD1582 reference when varying both temperature and
supply voltage. As is evident from the graph, the AD1582 supply
current increases only 1.0 µA/V, making this device extremely
attractive for use in applications where there may be wide varia-
tions in supply voltage and a need to minimize power dissipation.
0
–50
100
–50
–25
0
25
50
75
100
TEMPERATURE (ꢂC)
Figure 5. Residual Drift Error
OUTPUT VOLTAGE HYSTERESIS
80
T
= +85ꢂC
T
= +25ꢂC
A
A
60
40
20
0
High performance industrial equipment manufacturers may
require the AD1582/AD1583/AD1584/AD1585 family to maintain
a consistent output voltage error at 25°C after the references are
operated over the full temperature range. While all references
exhibit a characteristic known as output voltage hysteresis, the
AD1582/AD1583/AD1584/AD1585 family is designed to minimize
this characteristic. This phenomenon can be quantified by
measuring the change in the +25°C output voltage after
temperature excursions from +125°C to +25°C, and from –40°C
to +25°C. Figure 6 displays the distribution of the AD1582
output voltage hysteresis.
T
= –40ꢂC
A
3
4
5
6
7
8
9
10
11
V
(V)
IN
Figure 7. Typical Supply Current over Temperature
SUPPLY VOLTAGE
One of the ideal features of the AD1582/AD1583/AD1584/AD1585
is low supply voltage headroom. The parts can operate at
supply voltages as low as 200 mV above VOUT and up to 12 V.
However, if negative voltage is inadvertently applied to VIN with
respect to ground or any negative transient, >5 V is coupled to
VIN and the device may be damaged.
REV. D
–10–
AD1582/AD1583/AD1584/AD1585
AC PERFORMANCE
NOISE PERFORMANCE AND REDUCTION
To apply the AD1582/AD1583/AD1584/AD1585 family of
references, it is important to understand the effects of dynamic
output impedance and power supply rejection. In Figure 8a, a
voltage divider is formed by the AD1582’s output impedance and
by the external source impedance. Figure 8b shows the effect of
varying the load capacitor on the reference output. Power supply
rejection ratio (PSRR) should be determined when characterizing
the ac performance of a series voltage reference. Figure 9a shows a
test circuit used to measure PSRR, and Figure 9b demonstrates
the AD1582’s ability to attenuate line voltage ripple.
The noise generated by the AD1582 is typically less than
70 µV p-p over the 0.1 Hz to 10 Hz frequency band. Figure 10
shows the 0.1 Hz to 10 Hz noise of a typical AD1582. The noise
measurement is made with a high gain band-pass filter. Noise in
a 10 Hz to 10 kHz region is approximately 50 µV rms. Figure 11
shows the broadband noise of a typical AD1582. If further noise
reduction is desired, a 1-pole low-pass filter may be added
between the output pin and the ground. A time constant of 0.2 ms
has a –3 dB point at roughly 800 Hz, and reduces the high
frequency noise to about 16 µV rms. It should be noted,
however, that while additional filtering on the output may improve
the noise performance of the AD1582/AD1583/AD1584/AD1585
family, the added output impedance could degrade the ac
performance of the references.
V
DC
LOAD
5V
2kꢁ
10kꢁ
10kꢁ
2 ꢀ V
10kꢁ
OUT
5ꢃF
ꢀ1
DUT
ꢂ100ꢃA
1ꢃF
ꢂ2V
10ꢃV
1s
100
90
Figure 8a. Output Impedance Test Circuit
100
1ꢃF CAP
10
0%
10
AD1585
Figure 10. 0.1 Hz to 10 Hz Voltage Noise
AD1582
1
100ꢃV
10ms
100
90
0.1
10
100
1k
10k
100k
1M
FREQUENCY (Hz)
Figure 8b. Output Impedance vs. Frequency
10
0%
10kꢁ
10V
5V ꢂ100mV
ꢀ1
Figure 11. 10 Hz to 10 kHz Wideband Noise
V
0.22ꢃF
OUT
10kꢁ
DUT
ꢂ200mV
0.22ꢃ
F
Figure 9a. Ripple Rejection Test Circuit
100
90
80
70
60
50
40
30
20
10
0
AD1582
AD1585
1
10
100
1k
10k
100k
1M
FREQUENCY (Hz)
Figure 9b. Ripple Rejection vs. Frequency
REV. D
–11–
AD1582/AD1583/AD1584/AD1585
TURN-ON TIME
DYNAMIC PERFORMANCE
Many low power instrument manufacturers are becoming increas-
ingly concerned with the turn-on characteristics of the components
being used in their systems. Fast turn-on components often enable
the end user to save power by keeping power off when it is not
needed. Turn-on settling time is defined as the time required, after
the application of power (cold start), for the output voltage to
reach its final value within a specified error. The two major factors
affecting this are the active circuit settling time and the time
required for the thermal gradients on the chip to stabilize.
Figure 12a shows the turn-on settling and transient response test
circuit. Figure 12b shows the turn-on characteristic of the
AD1582. This characteristic is generated from cold-start operation
and represents the true turn-on waveform after power-up.
Figure 12c shows the fine settling characteristics of the AD1582.
Typically, the reference settles to within 0.1% of its final value
in about 100 µs.
Many A/D and D/A converters present transient current loads
to the reference, and poor reference response can degrade the
converter’s performance. The AD1582/AD1583/AD1584/AD1585
family of references provides superior static and dynamic line
and load regulation. Since these series references are capable of
both sourcing and sinking large current loads, they exhibit
excellent settling characteristics.
Figure 13 displays the line transient response for the AD1582.
The circuit used to perform such a measurement is shown in
Figure 12a, where the input supply voltage is toggled from 5 V
to 10 V and the input and output capacitors are each 0.22 µF.
Figures 14 and 15 show the load transient settling characteristics
for the AD1582 when load current steps of 0 mA to +5 mA
and 0 mA to –1 mA are applied. The input supply voltage
remains constant at 5 V, the input decoupling and output load
capacitors are 4.7 µF and 1 µF, respectively, and the output current
is toggled. For both positive and negative current loads, the
reference responses settle very quickly and exhibit initial voltage
spikes less than 10 mV.
The device can momentarily draw excessive supply current
when VSUPPLY is slightly below the minimum specified level.
Power supply resistance must be low enough to ensure reliable
turn-on. Fast power supply edges minimize this effect.
10kꢃ
5V
50ꢀs
5V OR 10V
0V OR 5V
0V OR 10V
0V TO 10V
100
90
ꢅ1
0.22ꢀF
V
OUT
10kꢃ
DUT
0.22ꢀF
Figure 12a. Turn-On/Transient Response Test Circuit
10
0%
200mV
50ꢀs
5V
20ꢀs
Figure 13. Line Transient Response
100
90
5V
20ꢀs
100
90
10
0%
1V
20ꢀs
Figure 12b. Turn-On Characteristics
10
0%
5mV
20ꢀs
5V
20ꢀs
Figure 14. Load Transient Response (0 mA to 5 mA Load)
100
90
20ꢀs
5V
100
90
10
0%
1mV
20ꢀs
Figure 12c. Turn-On Settling
10
0%
5mV
20ꢀs
Figure 15. Load Transient Response (0 mA to –1 mA Load)
REV. D
–12–
AD1582/AD1583/AD1584/AD1585
OUTLINE DIMENSIONS
3-Lead Small Outline Transistor Package [SOT-23-3]
(RT-3)
Dimensions shown in millimeters
3.04
2.90
2.80
1.40
1.30
1.20
3
2.64
2.10
1
2
PIN 1
0.95 BSC
1.90 BSC
1.12
0.89
0.20
0.08
0.10
0.01
0.60
0.50
0.40
0.50
0.30
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS TO-236AB
SOT-23 Tape and Reel
Dimensions shown in millimeters
7" REEL 100.00
4.10
4.00
3.90
1.10
1.00
0.90
OR
13" REEL 330.00
14.40 MAX
1.55
1.50
1.50
2.05
2.00
1.95
0.35
0.30
0.25
1.85
1.75
1.65
1.50 MIN
2.80
2.70
2.60
13.20
13.00
12.80
7" REEL 50.00 MIN
OR
13" REEL 100.00 MIN
20.20
MIN
8.30
8.00
7.70
3.55
3.50
3.45
3.20
3.10
2.90
0.75 MIN
1.00 MIN
9.90
8.40
8.40
DIRECTION OF UNREELING
REV. D
–13–
AD1582/AD1583/AD1584/AD1585
Revision History
Location
Page
6/04—Data Sheet Changed from REV. C to REV. D.
Changes to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
12/02—Data Sheet Changed from REV. B to REV. C.
Changes to FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Changes to GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Changes to SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Changes to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
TPC 3 replaced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Changes to TEMPERATURE PERFORMANCE section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 4 replaced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Changes to OUTPUT VOLTAGE HYSTERESIS section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
SOT-23 package updated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
REV. D
–14–
–15–
–16–
AD1585B 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
AD1585BRT | ADI | 2.5 V to 5.0 V Micropower, Precision Series Mode Voltage References | 获取价格 | |
AD1585BRT-R2 | ADI | 2.5 V to 5.0 V Micropower, Precision Series Mode Voltage References | 获取价格 | |
AD1585BRT-R2 | ROCHESTER | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 5V, PDSO3, TO-236AB, SOT-23, 3 PIN | 获取价格 | |
AD1585BRT-REEL | ADI | IC 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 5 V, PDSO3, PLASTIC, TO-236AB, SOT-23, 3 PIN, Voltage Reference | 获取价格 | |
AD1585BRT-REEL7 | ADI | 2.5 V to 5.0 V Micropower, Precision Series Mode Voltage References | 获取价格 | |
AD1585BRT-REEL7 | ROCHESTER | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 5 V, PDSO3, TO-236AB, SOT-23, 3 PIN | 获取价格 | |
AD1585BRTRL | ADI | 2.5 V to 5.0 V Micropower, Precision Series Mode Voltage References | 获取价格 | |
AD1585BRTRL7 | ADI | 2.5 V to 5.0 V Micropower, Precision Series Mode Voltage References | 获取价格 | |
AD1585BRTZ-REEL7 | ADI | 2.5 V to 5.0 V Micropower, Precision Series Mode Voltage References | 获取价格 | |
AD1585CRT-R2 | ADI | 2.5 V to 5.0 V Micropower, Precision Series Mode Voltage References | 获取价格 |
AD1585B 相关文章
- 2024-09-20
- 6
- 2024-09-20
- 9
- 2024-09-20
- 8
- 2024-09-20
- 6