ADP120-1-ACBZ30R7 [ADI]
IC,VOLT REGULATOR,FIXED,+3V,CMOS,BGA,4PIN,PLASTIC;
| 型号： | ADP120-1-ACBZ30R7 |
| 厂家： | 
ADI |
| 描述： | IC,VOLT REGULATOR,FIXED,+3V,CMOS,BGA,4PIN,PLASTIC |
| 文件： | 总20页 (文件大小：613K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
100 mA, Low Quiescent Current,
CMOS Linear Regulator
ADP120
FEATURES
TYPICAL APPLICATION CIRCUITS
ADP120
Input voltage range: 2.3 V to 5.5 V
Output voltage range: 1.2 V to 3.3 V
Output current: 100 mA
V
= 2.3V
V
= 1.8V
IN
OUT
1
2
3
5
VIN
GND
EN
VOUT
+
+
1µF
1µF
Low quiescent current
4
NC
I
I
GND = 11 μA with zero load
GND = 22 μA with 100 mA load
NC = NO CONNECT
Low shutdown current: <1 μA
Low dropout voltage
Figure 1. ADP120 TSOT with Fixed Output Voltage, 1.8 V
ADP120: 100 mV @ 100 mA load
ADP120-1: 60 mV @ 100 mA load
High PSRR
73 dB @ 1 kHz at VOUT = 1.2 V
70 dB @ 10 kHz at VOUT = 1.2 V
Low noise: 40 μV rms at VOUT = 1.2 V
No noise bypass capacitor required
Initial accuracy: 1ꢀ
Stable with small 1 μF ceramic output capacitor
16 fixed output voltage options
Current limit and thermal overload protection
Logic controlled enable
ADP120-1
V
= 2.3V
V
= 1.8V
OUT
IN
VIN
VOUT
+
+
1µF
1µF
EN
GND
Figure 2. ADP120-1 WLCSP with Fixed Output Voltage, 1.8 V
5-lead TSOT package
4-ball 0.4 mm pitch WLCSP
APPLICATIONS
Mobile phones
Digital camera and audio devices
Portable and battery-powered equipment
Post regulation
GENERAL DESCRIPTION
The ADP120 and ADP120-1 are low quiescent current, low
dropout, linear regulators that operate from 2.3 V to 5.5 V and
provide up to 100 mA of output current. The low 100 mV
dropout voltage at 100 mA load improves efficiency and allows
operation over a wide input voltage range. The low 25 μA of
quiescent current at full load make the ADP120 and the
ADP120-1 ideal for battery-operated portable equipment.
The ADP120 and ADP120-1 are available in 16 fixed output
voltage options, ranging from 1.2 V to 3.3 V. The parts are
optimized for stable operation with small 1 ꢀF ceramic output
capacitors. The ADP120 and ADP120-1 deliver good transient
performance with minimal board area.
Short-circuit protection and thermal overload protection circuits
prevent damage in adverse conditions. The ADP120 is available
in a tiny 5-lead TSOT and the ADP120-1 is available in a 4-ball
0.4 mm pitch WLCSP for the smallest footprint solution to
meet a variety of portable applications.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2008 Analog Devices, Inc. All rights reserved.
ADP120
TABLE OF CONTENTS
Features .............................................................................................. 1
Typical Performance Characteristics ..............................................7
Theory of Operation ...................................................................... 11
Applications Information.............................................................. 12
Capacitor Selection .................................................................... 12
Undervoltage Lockout ............................................................... 13
Enable Feature ............................................................................ 13
Current Limit and Thermal Overload Protection ................. 14
Thermal Considerations............................................................ 14
PCB Layout Considerations...................................................... 17
Outline Dimensions....................................................................... 18
Ordering Guide .......................................................................... 18
Applications....................................................................................... 1
Typical Application Circuits............................................................ 1
General Description......................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Recommended Specifications: Input and Output Capacitors 4
Absolute Maximum Ratings............................................................ 5
Thermal Data................................................................................ 5
Thermal Resistance ...................................................................... 5
ESD Caution.................................................................................. 5
Pin Configurations and Function Descriptions ........................... 6
REVISION HISTORY
5/08—Revision 0: Initial Version
Rev. 0 | Page 2 of 20
ADP120
SPECIFICATIONS
VIN = (VOUT + 0.4 V) or 2.3 V, whichever is greater; EN= VIN, IOUT = 10 mA, CIN = COUT = 1 ꢀF, TA = 25°C, unless otherwise noted.
Table 1.
Parameter
Symbol
VIN
Conditions
Min
Typ
11
Max
Unit
V
INPUT VOLTAGE RANGE
OPERATING SUPPLY CURRENT
TJ = −40°C to +125°C
IOUT = 0 μA
IOUT = 0 μA , TJ = −40°C to +125°C
IOUT = 10 mA
IOUT = 10 mA, TJ = −40°C to +125°C
IOUT = 100 mA
IOUT = 100 mA, TJ = −40°C to +125°C
EN = GND
2.3
5.5
IGND
μA
μA
μA
μA
μA
μA
μA
μA
%
21
29
35
15
22
SHUTDOWN CURRENT
IGND-SD
0.1
EN = GND, TJ = −40°C to +125°C
IOUT = 10 mA
1.5
+1
FIXED OUTPUT VOLTAGE ACCURACY VOUT
−1
100 μA < IOUT < 100 mA,VIN = (VOUT + 0.4 V) to 5.5 V
−2
+2
%
100 μA < IOUT < 100 mA,VIN = (VOUT + 0.4 V) to 5.5 V,
TJ = −40°C to +125°C
−2.5
+2.5
%
REGULATION
Line Regulation
∆VOUT/∆VIN VIN = (VOUT + 0.4 V) to 5.5 V, IOUT = 1 mA,
TJ = −40°C to +125°C
∆VOUT/∆IOUT IOUT = 1 mA to 100 mA
−0.03
+0.03
0.005
%/V
Load Regulation1
0.001
%/mA
%/mA
IOUT = 1 mA to 100 mA, TJ = −40°C to +125°C
DROPOUT VOLTAGE2
ADP120
VDROPOUT
VOUT = 3.3 V
IOUT = 10 mA
IOUT = 10 mA, TJ = −40°C to +125°C
IOUT = 100 mA
IOUT = 100 mA, TJ = −40°C to +125°C
IOUT = 10 mA
IOUT = 10 mA, TJ = −40°C to +125°C
IOUT = 100 mA
IOUT = 100 mA, TJ = −40°C to +125°C
VOUT = 3.3 V
8
mV
mV
mV
mV
mV
mV
mV
mV
μs
12
120
9
80
6
ADP120-1
60
90
START-UP TIME3
CURRENT LIMIT THRESHOLD4
TSTART-UP
ILIMIT
120
180
110
1.2
350
mA
THERMAL SHUTDOWN
Thermal Shutdown Threshold
Thermal Shutdown Hysteresis
TSSD
TJ rising
150
15
°C
°C
TSSD-HYS
EN INPUT
EN Input Logic High
EN Input Logic Low
EN Input Leakage Current
VIH
VIL
VI-LEAKAGE
2.3 V ≤ VIN ≤ 5.5 V
2.3 V ≤ VIN ≤ 5.5 V
EN = VIN or GND
EN = VIN or GND, TJ = −40°C to +125°C
V
V
μA
μA
0.4
1
0.05
UNDERVOLTAGE LOCKOUT
Input Voltage Rising
Input Voltage Falling
Hysteresis
UVLO
UVLORISE
UVLOFALL
UVLOHYS
OUTNOISE
TJ = −40°C to +125°C
TJ = −40°C to +125°C
2.25
V
V
mV
1.5
120
65
52
OUTPUT NOISE
10 Hz to 100 kHz, VIN = 5 V, VOUT = 3.3 V
10 Hz to 100 kHz, VIN = 5 V, VOUT = 2.5 V
10 Hz to 100 kHz, VIN = 5 V, VOUT = 1.2 V
μV rms
μV rms
μV rms
40
Rev. 0 | Page 3 of 20
ADP120
Parameter
Symbol
Conditions
Min
Typ
60
66
Max
Unit
dB
dB
POWER SUPPLY REJECTION RATIO
PSRR
10 kHz, VIN = 5 V, VOUT = 3.3 V
10 kHz, VIN = 5 V, VOUT = 2.5 V
10 kHz, VIN = 5 V, VOUT = 1.2 V
70
dB
1 Based on an endpoint calculation using 1 mA and 100 mA loads. See Figure 6 for typical load regulation performance for loads less than 1 mA.
2 Dropout voltage is defined as the input-to-output voltage differential when the input voltage is set to the nominal output voltage. This applies only for output
voltages above 2.3 V.
3 Start-up time is defined as the time between the rising edge of EN to VOUT being at 90% of its nominal value.
4 Current limit threshold is defined as the current at which the output voltage drops to 90% of the specified typical value. For example, the current limit for a 3.0 V
output voltage is defined as the current that causes the output voltage to drop to 90% of 3.0 V, or 2.7 V.
RECOMMENDED SPECIFICATIONS: INPUT AND OUTPUT CAPACITORS
Table 2.
Parameter
Symbol
CAPMIN
RESR
Conditions
TJ = −40°C to +125°C
TJ = −40°C to +125°C
Min
Typ
Max
Unit
μF
MINIMUM INPUT AND OUTPUT CAPACITANCE1
0.70
0.001
CAPACITOR ESR
1
Ω
1 The minimum input and output capacitance should be greater than 0.70 ꢀF over the full range of operating conditions. The full range of operating conditions in the
application must be considered during device selection to ensure that the minimum capacitance specification is met. X7R- and X5R-type capacitors are recommended,
Y5V and Z5U capacitors are not recommended for use with any LDO.
Rev. 0 | Page 4 of 20
ADP120
ABSOLUTE MAXIMUM RATINGS
Table 3.
Junction-to-ambient thermal resistance (θJA) of the package is
based on modeling and calculation using a four-layer board.
The junction-to-ambient thermal resistance is highly dependent
on the application and board layout. In applications where high
maximum power dissipation exists, close attention to thermal
board design is required. The value of θJA may vary, depending on
PCB material, layout, and environmental conditions. Specified
value of θJA is based on a four-layer, 4 in. × 3 in., 2 1/2 oz.
copper board, as per JEDEC standards. For more information,
see Application Note AN-772, A Design and Manufacturing
Guide for the Lead Frame Chip Scale Package (LFCSP).
Parameter
Rating
VIN to GND
VOUT to GND
−0.3 V to +6 V
−0.3 V to VIN
EN to GND
−0.3 V to +6 V
−65°C to +150°C
−40°C to +125°C
JEDEC J-STD-020
Storage Temperature Range
Operating Junction Temperature Range
Soldering Conditions
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ΨJB is the junction-to-board thermal characterization parameter
with units of °C/W. ΨJB of the package is based on modeling and
calculation using a four-layer board. The JESD51-12, Guidelines
for Reporting and Using Package Thermal Information, states
that thermal characterization parameters are not the same as
thermal resistances. ΨJB measures the component power flowing
through multiple thermal paths rather than a single path as in
thermal resistance, θJB. Therefore, ΨJB thermal paths include
convection from the top of the package as well as radiation from
the package, factors that make ΨJB more useful in real-world
applications. Maximum junction temperature (TJ) is calculated
from the board temperature (TB) and power dissipation (PD)
using the formula
THERMAL DATA
Absolute maximum ratings apply individually only, not in
combination. The ADP120 and ADP120-1 can be damaged
when the junction temperature limits are exceeded. Monitoring
ambient temperature does not guarantee that TJ is within the
specified temperature limits. In applications with high power
dissipation and poor thermal resistance, the maximum ambient
temperature may have to be derated.
TJ = TB + (PD × ΨJB)
In applications with moderate power dissipation and low PCB
thermal resistance, the maximum ambient temperature can
exceed the maximum limit as long as the junction temperature
is within specification limits. The junction temperature (TJ) of
the device is dependent on the ambient temperature (TA), the
power dissipation of the device (PD), and the junction-to-ambient
thermal resistance of the package (θJA).
Refer to JESD51-8 and JESD51-12 for more detailed informa-
tion about ΨJB.
THERMAL RESISTANCE
θJA and ΨJB are specified for the worst-case conditions, that is, a
device soldered in a circuit board for surface-mount packages.
Maximum junction temperature (TJ) is calculated from the
ambient temperature (TA) and power dissipation (PD) using the
formula
Table 4. Thermal Resistance
Package Type
θJA
ΨJB
43
58
Unit
°C/W
°C/W
5-Lead TSOT
4-Ball, 0.4 mm Pitch WLCSP
170
260
TJ = TA + (PD × θJA)
ESD CAUTION
Rev. 0 | Page 5 of 20
ADP120
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
ADP120-1
1
2
1
2
3
5
VIN
GND
EN
VOUT
A
B
VIN
VOUT
ADP120
TOP VIEW
(Not to Scale)
TOP VIEW
(Not to Scale)
4
NC
EN
GND
NC = NO CONNECT
Figure 4. 4-Ball WLCSP Pin Configuration
Figure 3. 5-Lead TSOT Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
Mnemonic Description
TSOT WLCSP
1
2
3
A1
B2
B1
VIN
GND
EN
Regulator Input Supply. Bypass VIN to GND with a 1 μF or greater capacitor.
Ground.
Enable Input. Drive EN high to turn on the regulator; drive EN low to turn off the regulator. For automatic
startup, connect EN to VIN.
4
5
N/A
A2
NC
VOUT
No Connect. Not connected internally.
Regulated Output Voltage. Bypass VOUT to GND with a 1 μF or greater capacitor.
Rev. 0 | Page 6 of 20
ADP120
TYPICAL PERFORMANCE CHARACTERISTICS
VIN = 2.3 V, VOUT = 1.8 V, IOUT = 10 mA, CIN = COUT = 1 ꢀF, TA = 25°C, unless otherwise noted.
35
LOAD = 10µA
LOAD = 100µA
1.804
LOAD = 1mA
LOAD = 10mA
LOAD = 100mA
30
1.802
1.800
1.798
1.796
1.794
1.792
1.790
25
20
15
10
5
LOAD = 10µA
LOAD = 100µA
LOAD = 1mA
LOAD = 10mA
LOAD = 100mA
0
–40°C
–5°C
25°C
(°C)
85°C
125°C
–40°C
–5°C
25°C
(°C)
85°C
125°C
T
J
T
J
Figure 5. Output Voltage vs. Junction Temperature
Figure 8. Ground Current vs. Junction Temperature
30
1.805
1.803
1.801
1.799
1.797
1.795
25
20
15
10
5
0
0.01
0.1
1
10
100
0.01
0.1
1
10
100
I
(mA)
I
(mA)
LOAD
LOAD
Figure 9. Ground Current vs. Load Current
Figure 6. Output Voltage vs. Load Current
1.805
1.803
1.801
1.799
1.797
1.795
30
25
20
15
10
5
LOAD = 10µA
LOAD = 100µA
LOAD = 1mA
LOAD = 10mA
LOAD = 100mA
LOAD = 10µA
LOAD = 100µA
LOAD = 1mA
LOAD = 10mA
LOAD = 100mA
0
2.3 2.5 2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5
2.3 2.5 2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5
V
(V)
V
(V)
IN
IN
Figure 10. Ground Current vs. Input Voltage
Figure 7. Output Voltage vs. Input Voltage
Rev. 0 | Page 7 of 20
ADP120
0.35
0.30
0.25
0.20
0.15
0.10
0.05
80
70
60
50
40
30
20
10
0
V
= 3.3V
2.30V
2.50V
3.00V
3.50V
4.20V
5.50V
OUT
= 25°C
T
A
0
–50
–25
0
25
50
75
100
125
1
10
(mA)
100
TEMPERATURE (°C)
I
LOAD
Figure 11. Shutdown Current vs. Temperature at Various Input Voltages
Figure 14. Dropout Voltage vs. Load Current, WLCSP, VOUT = 3.3 V
80
3.35
V
= 3.3V
OUT
= 25°C
T
A
70
60
50
40
30
20
10
0
3.30
3.25
3.20
3.15
V
V
V
V
V
@ 1mA
OUT
OUT
OUT
OUT
OUT
@ 10mA
@ 20mA
@ 50mA
@ 100mA
3.10
3.05
1
10
(mA)
100
3.20
3.25
3.30
3.35
3.40
(V)
3.45
3.50
3.55
3.60
I
V
LOAD
IN
Figure 12. Dropout Voltage vs. Load Current, TSOT, VOUT = 3.3 V
Figure 15. Output Voltage vs. Input Voltage (in Dropout), WLCSP, VOUT = 3.3 V
3.35
60
I
I
I
I
I
@ 1mA
LOAD
LOAD
LOAD
LOAD
LOAD
@ 10mA
@ 20mA
@ 50mA
@ 100mA
3.30
3.25
3.20
3.15
50
40
30
20
10
0
V
V
V
V
V
@ 1mA
OUT
OUT
OUT
OUT
OUT
@ 10mA
@ 20mA
@ 50mA
@ 100mA
3.10
3.05
3.20
3.25
3.30
3.35
3.40
(V)
3.45
3.50
3.55
3.60
3.20
3.25
3.30
3.35
3.40
(V)
3.45
3.50
3.55
3.60
V
V
IN
IN
Figure 16. Ground Current vs. Input Voltage (in Dropout)
Figure 13. Output Voltage vs. Input Voltage (in Dropout), TSOT, VOUT = 3.3 V
Rev. 0 | Page 8 of 20
ADP120
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
100mA
10mA
1mA
100µA
NO LOAD
V
V
V
= 50mV
3.3V/100mA
3.3V/100µA
1.2V/100mA
1.2V/100µA
1.8V/100mA
1.8V/100µA
RIPPLE
= 5V
IN
= 1.2V
= 1µF
OUT
C
OUT
10
100
1k
10k
100k
1M
10M
10
100
1k
10k
100k
1M
10M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 17. Power Supply Rejection Ratio vs. Frequency
Figure 20. Power Supply Rejection Ratio vs. Frequency
Various Output Voltages and Load Currents
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
10
100mA
10mA
1mA
100µA
NO LOAD
V
V
V
= 50mV
RIPPLE
= 5V
IN
= 1.8V
= 1µF
OUT
C
OUT
3.3V
1.8V
1
1.2V
0.1
0.01
10
100
1k
10k
100k
1M
10M
10
100
1k
10k
100k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 18. Power Supply Rejection Ratio vs. Frequency
Figure 21. Output Noise Spectrum, VIN = 5 V, ILOAD = 10 mA, COUT = 1 μF
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
70
100mA
10mA
1mA
100µA
NO LOAD
V
V
V
= 50mV
3.3V
RIPPLE
= 5V
IN
= 3.3V
= 1µF
60
OUT
C
OUT
2.5V
50
1.8V
1.5V
1.2V
40
30
20
10
0
10
100
1k
10k
100k
1M
10M
0.001
0.01
0.1
I
1
10
100
FREQUENCY (Hz)
(mA)
LOAD
Figure 19. Power Supply Rejection Ratio vs. Frequency
Figure 22. Output Noise vs. Load Current and Output Voltage
VIN = 5 V, COUT = 1 μF
Rev. 0 | Page 9 of 20
ADP120
I
I
LOAD
LOAD
1mA TO 100mA LOAD STEP,
2.5A/µs
4V TO 5V INPUT VOLTAGE STEP,
2V/µs
V
OUT
V
OUT
V
V
= 5V
= 1.8V
V
C
= 1.8V,
IN
OUT
OUT
= C
= 1µF
IN
OUT
(40µs/DIV)
(4µs/DIV)
Figure 23. Load Transient Response, CIN and COUT = 1 μF
Figure 25. Line Transient Response, Load Current = 100 mA
I
LOAD
I
LOAD
1mA TO 100mA LOAD STEP,
2.5A/µs
4V TO 5V INPUT VOLTAGE STEP,
2V/µs
V
OUT
V
OUT
V
V
= 5V
= 1.8V
V
C
= 1.8V,
IN
OUT
OUT
= C
= 1µF
IN
OUT
(40µs/DIV)
(10µs/DIV)
Figure 24. Load Transient Response, CIN and COUT = 4.7 μF
Figure 26. Line Transient Response, Load Current = 1 mA
Rev. 0 | Page 10 of 20
ADP120
THEORY OF OPERATION
The ADP120 and ADP120-1 are low quiescent current, low
dropout linear regulators that operate from 2.3 V to 5.5 V and
provide up to 100 mA of output current. Drawing a low 22 μA
of quiescent current (typical) at full load makes the ADP120
and ADP120-1 ideal for battery-operated portable equipment.
Shutdown current consumption is typically 100 nA.
Internally, the ADP120 and ADP120-1 consist of a reference, an
error amplifier, a feedback voltage divider, and a PMOS pass tran-
sistor. Output current is delivered via the PMOS pass device,
which is controlled by the error amplifier. The error amplifier
compares the reference voltage with the feedback voltage from
the output and amplifies the difference. If the feedback voltage
is lower than the reference voltage, the gate of the PMOS device
is pulled lower, allowing more current to pass and increasing
the output voltage. If the feedback voltage is higher than the
reference voltage, the gate of the PMOS device is pulled higher,
allowing less current to pass and decreasing the output voltage.
Optimized for use with small 1 ꢀF ceramic capacitors, the
ADP120 and ADP120-1 provide excellent transient
performance.
ADP120
VIN
GND
EN
VOUT
The ADP120 and ADP120-1 are available in 16 output voltage
options, ranging from 1.2 V to 3.3 V. The ADP120 and ADP120-1
use the EN pin to enable and disable the VOUT pin under normal
operating conditions. When EN is high, VOUT turns on, when
EN is low, VOUT turns off. For automatic startup, EN can be
tied to VIN.
R1
SHORT CIRCUIT,
UVLO, AND
THERMAL
PROTECT
SHUTDOWN
0.8V REFERENCE
R2
Figure 27. Internal Block Diagram
Rev. 0 | Page 11 of 20
ADP120
APPLICATIONS INFORMATION
CAPACITOR SELECTION
Input and Output Capacitor Properties
Output Capacitor
Use any good quality ceramic capacitors with the ADP120 or
ADP120-1, as long as they meet the minimum capacitance and
maximum ESR requirements. Ceramic capacitors are manufac-
tured with a variety of dielectrics, each with different behavior
over temperature and applied voltage. Capacitors must have a
dielectric adequate to ensure the minimum capacitance over
the necessary temperature range and dc bias conditions. X5R
or X7R dielectrics with a voltage rating of 6.3 V or 10 V are
recommended for best performance. Y5V and Z5U dielectrics
are not recommended for use with any LDO because of their
poor temperature and dc bias characteristics.
The ADP120 and ADP120-1 are designed for operation with
small, space-saving ceramic capacitors, but function with most
commonly used capacitors as long as care is taken with regard
to the effective series resistance (ESR) value. The ESR of the
output capacitor affects stability of the LDO control loop. A
minimum of 0.70 ꢀF capacitance with an ESR of 1 Ω or less is
recommended to ensure stability of the ADP120 and ADP120-1.
Transient response to changes in load current is also affected by
output capacitance. Using a larger value of output capacitance
improves the transient response of the ADP120 and ADP120-1
to large changes in load current. Figure 28 and Figure 29 show
the transient responses for output capacitance values of 1 ꢀF
and 4.7 ꢀF, respectively.
Figure 30 depicts the capacitance vs. voltage bias characteristic
of a 0402 1 ꢀF, 10 V, X5R capacitor. The voltage stability of a capa-
citor is strongly influenced by the capacitor size and voltage rating.
In general, a capacitor in a larger package or higher voltage rating
exhibits better stability. The temperature variation of the X5R
dielectric is about 15ꢁ over the −40°C to +85°C temperature
range and is not a function of package or voltage rating.
1.2
I
LOAD
1mA TO 100mA LOAD STEP,
2.5A/µs
MURATA PART NUMBER:
GRM155R61A105KE15
1.0
0.8
0.6
0.4
0.2
0
V
OUT
V
C
= 1.8V,
OUT
= C
= 1µF
IN
OUT
(400ns/DIV)
Figure 28. Output Transient Response, COUT = 1 ꢀF
I
LOAD
1mA TO 100mA LOAD STEP,
2.5A/µs
0
2
4
6
8
10
VOLTAGE (V)
Figure 30. Capacitance vs. Voltage Characteristic
Use Equation 1 to determine the worst-case capacitance accounting
for capacitor variation over temperature, component tolerance,
and voltage.
V
OUT
CEFF = CBIAS × (1 − TEMPCO) × (1 − TOL)
(1)
where:
V
C
= 1.8V,
OUT
= C
= 4.7µF
IN
OUT
CBIAS is the effective capacitance at the operating voltage.
(400ns/DIV)
TEMPCO is the worst-case capacitor temperature coefficient.
TOL is the worst-case component tolerance.
Figure 29. Output Transient Response, COUT = 4.7 ꢀF
Input Bypass Capacitor
In this example, the worst-case temperature coefficient
(TEMPCO) over −40°C to +85°C is assumed to be 15ꢁ for an
X5R dielectric. The tolerance of the capacitor (TOL) is assumed
to be 10ꢁ, and CBIAS is 0.94 μF at 1.8 V as shown in Figure 30.
Connecting a 1 ꢀF capacitor from VIN to GND reduces the cir-
cuit sensitivity to printed circuit board (PCB) layout, especially
when long input traces or high source impedance are encountered.
If greater than 1 ꢀF of output capacitance is required, increase
the input capacitor to match it.
Substituting these values in Equation 1 yields
CEFF = 0.94 μF × (1 − 0.15) × (1 − 0.1) = 0.719 μF
Rev. 0 | Page 12 of 20
ADP120
1.10
1.05
1.00
0.95
0.90
0.85
0.80
0.75
0.70
Therefore, the capacitor chosen in this example meets the
minimum capacitance requirement of the LDO over temper-
ature and tolerance at the chosen output voltage.
To guarantee the performance of the ADP120 and ADP120-1, it
is imperative that the effects of dc bias, temperature, and toler-
ances on the behavior of the capacitors are evaluated for each
application.
EN ACTIVE
EN INACTIVE
UNDERVOLTAGE LOCKOUT
The ADP120 and ADP120-1 each have an internal undervol-
tage lockout circuit that disables all inputs and the output when
the input voltage is less than approximately 2.2 V. This ensures
that the ADP120 and ADP120-1 inputs and the output behave in
a predictable manner during power-up.
2.25 2.50 2.75 3.00 3.25 3.50 3.75 4.00 4.25 4.50 4.75 5.00 5.25 5.50
V
(V)
IN
Figure 32. Typical EN Pin Thresholds vs. Input Voltage
ENABLE FEATURE
The ADP120 and ADP120-1 utilize an internal soft start to limit
the inrush current when the output is enabled. The start-up
time for the 1.8 V option is approximately 120 ꢀs from the time
the EN active threshold is crossed to when the output reaches
90ꢁ of its final value. The start-up time is somewhat dependant
on the output voltage setting and increases slightly as the output
voltage increases.
The ADP120 and ADP120-1 use the EN pin to enable and
disable the VOUT pin under normal operating conditions. As
shown in Figure 31, when a rising voltage on EN crosses the active
threshold, VOUT turns on. When a falling voltage on EN
crosses the inactive threshold, VOUT turns off.
6
V
OUT
EN
5
EN
4
3.3V
3
V
V
= 5V
2
IN
1.8V
= 1.8V
OUT
C
= C
= 100mA
= 1µF
1.2V
IN
OUT
I
LOAD
1
(40ms/DIV)
Figure 31. Typical EN Pin Operation
0
0
20
40
60
80
100 120 140 160 180 200
TIME (µs)
As shown in Figure 31, the EN pin has hysteresis built-in. This
prevents on/off oscillations that can occur due to noise on the
EN pin as it passes through the threshold points.
Figure 33. Typical Start-Up Time
The EN pin active/inactive thresholds are derived from the VIN
voltage; therefore, these thresholds vary with changing input
voltage. Figure 32 shows typical EN active/inactive thresholds
when the input voltage varies from 2.3 V to 5.5 V.
Rev. 0 | Page 13 of 20
ADP120
To guarantee reliable operation, the junction temperature of
the ADP120 and ADP120-1 must not exceed 125°C. To ensure
the junction temperature stays below this maximum value, the
user needs to be aware of the parameters that contribute to
junction temperature changes. These parameters include ambient
temperature, power dissipation in the power device, and thermal
resistances between the junction and ambient air (θJA). The θJA
number is dependent on the package assembly compounds that
are used and the amount of copper used to solder the package
GND pins to the PCB. Table 6 shows typical θJA values of the
5-lead TSOT and 4-ball WLCSP packages for various PCB copper
sizes. Table 7 shows the typical ΨJB value of the 5-lead TSOT and
4-ball WLCSP.
CURRENT LIMIT AND THERMAL OVERLOAD
PROTECTION
The ADP120 and ADP120-1 are protected against damage due
to excessive power dissipation by current and thermal overload
protection circuits. The ADP120 and ADP120-1 are designed to
current limit when the output load reaches 150 mA (typical).
When the output load exceeds 150 mA, the output voltage
reduces to maintain a constant current limit.
Thermal overload protection is built-in limiting the junction
temperature to a maximum of 150°C (typical). Under extreme
conditions (that is, high ambient temperature and power dissi-
pation) when the junction temperature starts to rise above 150°C,
the output turns off, reducing the output current to zero. When
the junction temperature drops below 135°C, the output turns
on again restoring output current to its nominal value.
Table 6. Typical θJA Values
θJA (°C/W)
Copper Size (mm2)
01
ADP120
170
ADP120-1
260
Consider the case where a hard short from VOUT to GND
occurs. At first, the ADP120 and ADP120-1 current limit
conducting only 150 mA into the short. If self-heating of the
junction is great enough to cause its temperature to rise above
150°C, thermal shutdown activates, turning off the output and
reducing the output current to zero. As the junction tempera-
ture cools and drops below 135°C, the output turns on and
conducts 150 mA into the short, again causing the junction
temperature to rise above 150°C. This thermal oscillation
between 135°C and 150°C causes a current oscillation between
150 mA and 0 mA that continues as long as the short remains at
the output.
50
152
159
100
300
500
146
134
131
157
153
151
1 Device soldered to minimum size pin traces.
Table 7. Typical ΨJB Values
ΨJB (°C/W)
ADP120, TSOT
ADP120-1, WLCSP
58.4
42.8
The junction temperature of the ADP120 and ADP120-1 can be
calculated from the following equation:
Current and thermal limit protections are intended to protect
the device against accidental overload conditions. For reliable
operation, device power dissipation must be externally limited
to prevent junction temperatures from exceeding 125°C.
TJ = TA + (PD × θJA)
where:
(2)
TA is the ambient temperature.
PD is the power dissipation in the die, given by
THERMAL CONSIDERATIONS
In most applications, the ADP120 and ADP120-1 do not dissi-
pate much heat due to their high efficiency. However, in
PD = [(VIN − VOUT) × ILOAD] + (VIN × IGND
)
(3)
applications with high ambient temperature, high supply voltage to
output voltage differential, the heat dissipated in the package is
large enough that it can cause the junction temperature of the
die to exceed the maximum junction temperature of 125°C.
where:
I
I
LOAD is the load current.
GND is the ground current.
V
IN and VOUT are input and output voltages, respectively.
When the junction temperature exceeds 150°C, the converter
enters thermal shutdown. It recovers only after the junction
temperature has decreased below 135°C to prevent any permanent
damage. Therefore, thermal analysis for the chosen application
is very important to guarantee reliable performance over all
conditions. The junction temperature of the die is the sum of
the ambient temperature of the environment and the tempera-
ture rise of the package due to the power dissipation, as shown
in Equation 2.
Power dissipation due to ground current is quite small and can
be ignored. Therefore, the junction temperature equation
simplifies to the following:
TJ = TA + {[(VIN − VOUT) × ILOAD] × θJA}
(4)
As shown in Equation 4, for a given ambient temperature, input-
to-output voltage differential, and continuous load current there
exists a minimum copper size requirement for the PCB to ensure
the junction temperature does not rise above 125°C. The following
figures show junction temperature calculations for different
ambient temperatures, load currents, VIN-to-VOUT differentials,
and areas of PCB copper.
Rev. 0 | Page 14 of 20
ADP120
140
120
100
80
140
120
100
80
MAX JUNCTION TEMPERATURE
MAX JUNCTION TEMPERATURE
I
= 100mA
L
I
= 75mA
= 50mA
= 25mA
L
I
= 100mA
L
I
L
I
= 75mA
L
I
L
60
60
I
= 50mA
= 25mA
L
I
L
I
= 10mA
40
40
L
I
= 1mA
L
20
20
I
= 10mA
3.5
L
I
= 1mA
L
0
0.5
0
0.5
1.0
1.5
2.0
2.5
– V
3.0
(V)
4.0
4.5
4.5
4.5
1.0
1.5
2.0
2.5
– V
3.0
(V)
3.5
4.0
4.5
V
V
IN
IN
OUT
OUT
Figure 34. TSOT, 500 mm2 of PCB Copper, TA = 25°C
Figure 37. TSOT, 500 mm2 of PCB Copper, TA = 50°C
140
120
100
80
140
120
100
80
MAX JUNCTION TEMPERATURE
MAX JUNCTION TEMPERATURE
I
= 100mA
L
I
= 75mA
L
I
= 100mA
L
I
= 50mA
= 25mA
L
I
= 75mA
= 50mA
= 25mA
L
I
L
I
60
60
L
I
L
40
40
I
= 10mA
L
I
= 1mA
L
20
20
I
= 10mA
3.5
L
I
= 1mA
L
0
0
0.5
0.5
1.0
1.5
2.0
2.5
– V
3.0
(V)
4.0
1.0
1.5
2.0
2.5
– V
3.0
(V)
3.5
4.0
4.5
V
V
IN
IN
OUT
OUT
Figure 35. TSOT, 100 mm2 of PCB Copper, TA = 25°C
Figure 38. TSOT, 100 mm2 of PCB Copper, TA = 50°C
140
120
100
80
140
120
100
80
MAX JUNCTION TEMPERATURE
MAX JUNCTION TEMPERATURE
I
= 100mA
L
I
= 75mA
L
I
= 100mA
L
I
= 50mA
L
I
= 75mA
= 50mA
L
I
= 25mA
= 1mA
L
I
L
60
60
I
= 25mA
L
I
= 10mA
L
40
40
I
L
20
20
I
= 10mA
3.5
L
I
= 1mA
L
0
0
0.5
0.5
1.0
1.5
2.0
2.5
– V
3.0
(V)
4.0
1.0
1.5
2.0
2.5
– V
3.0
(V)
3.5
4.0
4.5
V
V
IN
IN
OUT
OUT
Figure 36. TSOT, 0 mm2 of PCB Copper, TA = 25°C
Figure 39. TSOT, 0 mm2 of PCB Copper, TA = 50°C
Rev. 0 | Page 15 of 20
ADP120
140
120
100
80
140
120
100
80
MAX JUNCTION TEMPERATURE
MAX JUNCTION TEMPERATURE
I
= 100mA
L
I
= 75mA
L
I
= 100mA
L
I
= 50mA
= 25mA
L
I
= 75mA
= 50mA
= 25mA
L
I
L
I
60
60
L
I
L
40
40
I
= 10mA
L
I
= 1mA
L
20
20
I
= 10mA
3.5
L
I
= 1mA
L
0
0.5
0
0.5
1.0
1.5
2.0
2.5
– V
3.0
(V)
4.0
4.5
1.0
1.5
2.0
2.5
– V
3.0
(V)
3.5
4.0
4.5
V
V
IN
IN
OUT
OUT
Figure 40. WLCSP, 500 mm2 of PCB Copper, TA = 25°C
Figure 43. WLCSP, 500 mm2 of PCB Copper, TA = 50°C
140
120
100
80
140
120
100
80
MAX JUNCTION TEMPERATURE
MAX JUNCTION TEMPERATURE
I
= 100mA
L
I
= 75mA
L
I
= 100mA
L
I
= 50mA
= 25mA
L
I
= 75mA
= 50mA
= 25mA
L
I
L
I
L
60
60
I
L
40
40
I
= 10mA
L
I
= 1mA
L
20
20
I
= 10mA
3.5
L
I
= 1mA
L
0
0.5
0
0.5
1.0
1.5
2.0
2.5
– V
3.0
(V)
4.0
4.5
1.0
1.5
2.0
2.5
– V
3.0
(V)
3.5
4.0
4.5
V
V
IN
IN
OUT
OUT
Figure 41. WLCSP, 100 mm2 of PCB Copper, TA = 25°
Figure 44. WLCSP, 100 mm2 of PCB Copper, TA = 50°
140
120
100
80
140
120
100
80
MAX JUNCTION TEMPERATURE
MAX JUNCTION TEMPERATURE
I
= 75mA
I
= 100mA
L
I
= 100mA
L
L
I
= 75mA
L
I
= 50mA
= 25mA
L
I
= 50mA
= 25mA
L
I
L
60
60
I
L
I
= 10mA
40
40
L
I
= 1mA
L
20
20
I
= 10mA
L
I
= 1mA
L
0
0.5
0
0.5
1.0
1.5
2.0
2.5
– V
3.0
(V)
3.5
4.0
4.5
1.0
1.5
2.0
2.5
– V
3.0
(V)
3.5
4.0
4.5
V
V
IN
IN
OUT
OUT
Figure 42. WLCSP, 0 mm2 of PCB Copper, TA = 25°C
Figure 45. WLCSP, 0 mm2 of PCB Copper, TA = 50°C
Rev. 0 | Page 16 of 20
ADP120
PCB LAYOUT CONSIDERATIONS
In cases where the board temperature is known, use the thermal
characterization parameter, ΨJB, to estimate the junction
temperature rise. Maximum junction temperature (TJ) is
calculated from the board temperature (TB) and power
dissipation (PD) using the formula
Improve heat dissipation from the package by increasing the
amount of copper attached to the pins of the ADP120 and
ADP120-1. However, as listed in Table 6, a point of diminishing
returns is eventually reached, beyond which an increase in the
copper size does not yield significant heat dissipation benefits.
TJ = TB + (PD × ΨJB)
(5)
Place the input capacitor as close as possible to the VIN and
GND pins. Place the output capacitor as close as possible to the
VOUT and GND pins. Use of 0402- or 0603-size capacitors and
resistors achieves the smallest possible footprint solution on
boards where area is limited.
140
MAX JUNCTION TEMPERATURE
120
100
80
60
40
20
0
I
= 50mA
L
I
I
= 75mA
= 10mA
I
= 100mA
L
L
GND
GND
I
= 25mA
L
I
= 1mA
L
L
ANALOG DEVICES
ADP120-xx-EVALZ
C1
C2
U1
0.5
1.0
1.5
2.0
2.5
– V
3.0
3.5
4.0
4.5
V
(V)
IN
OUT
J1
Figure 46. TSOT, TA = 85°C
140
120
100
80
VIN
VOUT
MAX JUNCTION TEMPERATURE
I
= 50mA
L
I
= 75mA
I
= 100mA
L
L
EN
GND
GND
I
= 25mA
I
= 10mA
L
I
= 1mA
L
L
Figure 48. TSOT PCB Layout
60
J1
ADP120-1-xx-EVALZ
40
VOUT
VIN
20
C1
C2
U1
WLC
SP
0
0.5
1.0
1.5
2.0
2.5
– V
3.0
(V)
3.5
4.0
4.5
V
IN
OUT
GND
Figure 47. WLCSP, TA = 85°C
GND
EN
Figure 49. WLCSP PCB Layout
Rev. 0 | Page 17 of 20
ADP120
OUTLINE DIMENSIONS
2.90 BSC
5
1
4
3
2.80 BSC
1.60 BSC
2
PIN 1
0.95 BSC
1.90
BSC
*
0.90
0.87
0.84
*
1.00 MAX
0.20
0.08
8°
4°
0°
0.10 MAX
0.60
0.45
0.30
0.50
0.30
SEATING
PLANE
*
COMPLIANT TO JEDEC STANDARDS MO-193-AB WITH
THE EXCEPTION OF PACKAGE HEIGHT AND THICKNESS.
Figure 50. 5-Lead Thin Small Outline Transistor Package [TSOT]
(UJ-5)
Dimensions shown in millimeters
0.660
0.600
0.540
0.860
0.820 SQ
0.780
A1 BALL
CORNER
SEATING
PLANE
2
1
A
B
0.280
0.260
0.240
0.40
BALL PITCH
TOP VIEW
(BALL SIDE DOWN)
BOTTOM VIEW
(BALL SIDE UP)
0.230
0.200
0.170
0.050 NOM
COPLANARITY
Figure 51. 4-Ball Wafer Level Chip Scale Package [WLCSP]
(CB-4-2)
Dimensions shown in millimeters
ORDERING GUIDE
Output
Voltage (V)
Package
Option
Model
Temperature Range
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
Package Description
5-Lead TSOT
5-Lead TSOT
5-Lead TSOT
5-Lead TSOT
4-Ball WLCSP
4-Ball WLCSP
4-Ball WLCSP
4-Ball WLCSP
4-Ball WLCSP
4-Ball WLCSP
4-Ball WLCSP
Branding
L9R
L9Q
L9P
L9N
L8P
L8Q
L8R
L8S
L8T
L8U
L8V
ADP120-AUJZ12R71
ADP120-AUJZ15R71
ADP120-AUJZ18 R71
ADP120-AUJZ33R71
ADP120-1-ACBZ12R71
ADP120-1-ACBZ15R71
ADP120-1-ACBZ155R71
ADP120-1-ACBZ16R71
ADP120-1-ACBZ165R71
ADP120-1-ACBZ17R71
ADP120-1-ACBZ175R71
1.2
1.5
1.8
3.3
UJ-5
UJ-5
UJ-5
UJ-5
1.2
1.5
1.55
1.6
1.65
1.7
CB-4-2
CB-4-2
CB-4-2
CB-4-2
CB-4-2
CB-4-2
CB-4-2
1.75
Rev. 0 | Page 18 of 20
ADP120
Output
Voltage (V)
Package
Option
Model
Temperature Range
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
Package Description
Branding
L8W
L8X
L8Y
L8Z
L90
L91
L92
L93
ADP120-1-ACBZ18 R71
ADP120-1-ACBZ188R71
ADP120-1-ACBZ20R71
ADP120-1-ACBZ25R71
ADP120-1-ACBZ278R71
ADP120-1-ACBZ28R71
ADP120-1-ACBZ29R71
ADP120-1-ACBZ30R71
ADP120-1-ACBZ33R71
ADP120-33-EVALZ1
ADP120-18-EVALZ1
ADP120-15-EVALZ1
ADP120-12-EVALZ1
ADP120-1-28-EVALZ1
ADP120-1-25-EVALZ1
ADP120-1-18-EVALZ1
ADP120-1-15-EVALZ1
ADP120-1-12-EVALZ1
1.8
1.875
2.0
2.5
2.775
2.8
2.9
3.0
3.3
3.3
1.8
1.5
1.2
2.8
2.5
1.8
1.5
1.2
4-Ball WLCSP
4-Ball WLCSP
4-Ball WLCSP
4-Ball WLCSP
4-Ball WLCSP
4-Ball WLCSP
4-Ball WLCSP
4-Ball WLCSP
CB-4-2
CB-4-2
CB-4-2
CB-4-2
CB-4-2
CB-4-2
CB-4-2
CB-4-2
CB-4-2
4-Ball WLCSP
L94
ADP120 3.3 V Output Evaluation Board
ADP120 1.8 V Output Evaluation Board
ADP120 1.5 V Output Evaluation Board
ADP120 1.2 V Output Evaluation Board
ADP120-1 2.8 V Output Evaluation Board
ADP120-1 2.5 V Output Evaluation Board
ADP120-1 1.8 V Output Evaluation Board
ADP120-1 1.5 V Output Evaluation Board
ADP120-1 1.2 V Output Evaluation Board
1 Z = RoHS Compliant Part.
Rev. 0 | Page 19 of 20
ADP120
NOTES
©2008 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06901-0-5/08(0)
Rev. 0 | Page 20 of 20
相关型号：
©2020 ICPDF网 联系我们和版权申明