OCM22-JTDKV-DB [AGERE]
One-Chip Modem for Embedded Applications; 单芯片调制解调器，嵌入式应用
| 型号： | OCM22-JTDKV-DB |
| 厂家： | 
AGERE SYSTEMS |
| 描述： | One-Chip Modem for Embedded Applications |
| 文件： | 总4页 (文件大小：184K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Product Brief Rev 1.0
April 2005
OCM-22
One-Chip Modem for Embedded Applications
Features
Introduction
■ Controller and data pump in a single 48-pin TQFP
with two integrated peripheral interfaces:
— Partial ISA (8-bit parallel).
OCM-22 is a low-cost modem solution for low-speed
embedded applications. OCM22 includes a simplified
AT command set and supports data rates from
300 bits/s (V.21) to 2400 bits/s (V.22bis) and only
requires a CSP1034 or CSP1035A to make a com-
plete modem.
— RS232.
■ Data mode capabilities range:
— V.22bis: 2400 bits/s.
— V.22: 1200 bits/s.
— V.23: 1200/600 bits/s.
— V.21: 300 bits/s.
OCM-22 provides a choice of two system interfaces,
a serial interface or an 8-bit parallel interface. The
serial interface can be used in systems that have an
available serial port. In other systems, the parallel
interface can be I/O or memory mapped onto typical
processor buses.
— Bell 212A: 1200 bits/s.
— Bell 103: 300 bits/s.
■ Serial DTE interface:
— Hardware and software flow control.
— Asynchronous data format: 19,200 bits/s, 8-bit
data, no parity, 1 stop bit.
In typical applications, OCM-22 is paired with Agere's
CSP1035A silicon DAA to implement a low-cost
worldwide modem. OCM-22 can also be used with
Agere's CSP1034 line codec for traditional trans-
former-based DAA designs.
■ Parallel DTE interface for connection to system I/O
or memory bus.
■ DAA support:
— CSP1035A silicon DAA.
— CSP1034C with transformer DAA.
Applications
■ Set-top-box
■ Supports low-cost, call-progress speaker.
■ Verification machines
■ Point of sale
■ Support for country-specific settings
(homologation) under host control.
■ Supports extension phone detection for set-top
box applications when used with CSP1035A DAA.
■ Franking machines
■ Other low-speed data
■ Customized feature set using code downloads into
on-chip RAM.
■ Internal PLL to generate high-speed clocks from
external low-cost crystal.
■ Single 3.3 V supply.
■ Type 1 caller ID support (US, UK, France, Ger-
many, and Spain).
OCM-22
Product Brief Rev 1.0
April 2005
One-Chip Modem for Embedded Applications
Functional Description
The Agere Systems OCM-22 chip set is a two-chip solution consisting of an Agere Systems OCM-22 and a
CSP1034C or CSP1035A. A block diagram of the OCM-22 chip sets are illustrated in Figure 1 and Figure 2.
AGERE SYSTEMS
OCM-22 CONTROLLERLESS MODEM CHIP
U-DAA
OCM-22
CSP1035A (LINE-POWERED)
LINE
CODEC
UNIVERSAL
DAA
REMAINING
COMPONENTS
FOR
SYSTEM
MICRO-
PROCESSOR
TELEPHONE
LINE
U-DAA
PARALLEL/
SERIAL
48-PIN
TQFP
48-PIN TQFP
D5-9559 (F)a R.02
Figure 1. OCM-22 + CSP1035A Universal DAA Chip Set Block Diagram
AGERE SYSTEMS
OCM-22 CONTROLLERLESS MODEM CHIP
OCM-22
CSP1034C LINE
CODEC
STANDARD
DAA CIRCUIT
SYSTEM
MICRO-
TELEPHONE
LINE
PROCESSOR
SERIAL/
PARALLEL
48-PIN
TQFP
48-PIN TQFP
5-9560 (F)a R.02
Figure 2. OCM-22 + CSP1034C Chip Set Block Diagram
DIA Port
OCM-22 provides a system interface for use in embedded applications that requires only two address lines, a read/
write strobe, and a single chip select. The interface feeds directly into the DIAs four registers.
The following diagram shows how the host system and the OCM-22 interface. In this configuration, external logic
decodes the address that selects the DIA port, and the embedded application accesses the four control registers
associated with the DIA port to communicate with OCM-22. This configuration also allows a clean interface to
external plug-and-play and PCMCIA interface devices.
Agere Systems Inc.
2
OCM-22
Product Brief Rev 1.0
April 2005
One-Chip Modem for Embedded Applications
Functional Description (continued)
OCM-22 DEVICE
DATA[7:0]
ADDR[1:0]
READN
WRITEN
INTRPT
HD[7:0]
HA[1:0]
HRDN
HWRN
HINTR
ADDRESS
DECODE
HCSN
5-8104 (F) a
Figure 3. Parallel Interface to DIA Port
Internal PLL for Low-Speed Crystal Support
Power Requirements
OCM-22 supports low-speed, external crystals by
incorporating a PLL to support lower-cost crystals and
to ease the effort of minimizing EMI. If future code
needs higher clock rates, an internal multiplier can pro-
vide this without recertification or redesign of the exter-
nal hardware. OCM-22 requires an external 29.4912
MHz crystal or oscillator.
Both the OCM-22 device and the CSP1034C are
manufactured in low-power CMOS technology and are
designed to operate using only a single 3.3 V supply.
During operation, OCM-22's on-chip PLL can be set to
provide only the minimum internal clock rate required.
The CSP1035A is also manufactured in low-power
CMOS technology. However, the CSP1035A is fully
line powered. A shunt regulator maintains a monitored
2.7 V supply, during off-hook conditions. If the voltage
falls below 2.2 V, the chip saves its registers and goes
into reset. This allows the CSP1035A to retain the reg-
ister settings during a call bridge where the tip/ring volt-
age can collapse to 0 V for up to 400 ms and start up
again at the completion of the call break.
PWM Speaker Interface
The speaker driver employs a pulse-width modulated
algorithm, where 8-bit two's complement data is modu-
lated by a triangle wave. The following diagram shows
the recommended speaker configuration. This inex-
pensive configuration drives a low-impedance speaker
while obtaining a suitable volume. The SPKR signal is
fed to a transistor through a low-pass filter to remove
the carrier signal (cut-off frequency = 4 kHz).
+3.3 V
AT-08
3.3 kΩ
FDV301N
SPKR
10 kΩ
6800 pF
5-8105 (F)
Figure 4. Lower-Impedance Speaker Configuration
Agere Systems Inc.
3
OCM-22
Product Brief Rev 1.0
April 2005
One-Chip Modem for Embedded Applications
Package Information
CSP
1034C/
1035A
OCM22
48-PIN
TQFP
48-PIN
TQFP
DIME
(U.S.A.)
TOP VIEW
OCM-22
CSP1034C/1035A
DIME
SIDE VIEW
Figure 5. OCM-22 Data Pump Chip Set
Ordering Information
Table 1. Chip Set Names and Part Numbers
Device
Description
Package
48-pin TQFP
48-pin TQFP
48-pin TQFP
Part Number
Comcode
OCM-22
3.3 V Codec
Silicon DAA
Modem
CSP1034C
CSP1035A
OCM22-JTDKV-DB
CSP1034C-T11
CSP1035A-T11
700054307
108159542
108877077
MNP is a registered trademark of Microcom, Inc.
IEEE is a registered trademark of the Institute of Electrical and Electronics Engineers, Inc.
For additional information, contact your Agere Systems Account Manager or the following:
INTERNET:
E-MAIL:
Home: http://www.agere.com Sales: http://www.agere.com/sales
docmaster@agere.com
N. AMERICA: Agere Systems Inc., Lehigh Valley Central Campus, Room 10A-301C, 1110 American Parkway NE, Allentown, PA 18109-9138
1-800-372-2447, FAX 610-712-4106 (In CANADA: 1-800-553-2448, FAX 610-712-4106)
ASIA:
CHINA: (86) 21-54614688 (Shanghai), (86) 755-25881122 (Shenzhen)
JAPAN: (81) 3-5421-1600 (Tokyo), KOREA: (82) 2-767-1850 (Seoul), SINGAPORE: (65) 6741-9855, TAIWAN: (886) 2-2725-5858 (Taipei)
Tel. (44) 1344 296 400
EUROPE:
Agere Systems Inc. reserves the right to make changes to the product(s) or information contained herein without notice. No liability is assumed as a result of their use or application.
Agere, Agere Systems, and the Agere logo are registered trademarks of Agere Systems Inc.
Copyright © 2005 Agere Systems Inc.
All Rights Reserved
April 2005
PB03-202DMOD-1 (Replaces PB03-202DMOD)
相关型号：
©2020 ICPDF网 联系我们和版权申明