HCMS-2964 [AGILENT]
High Performance CMOS 5 x 7 Alphanumeric Displays; 高性能CMOS 5× 7文数字显示
| 型号： | HCMS-2964 |
| 厂家： | 
AGILENT TECHNOLOGIES, LTD. |
| 描述： | High Performance CMOS 5 x 7 Alphanumeric Displays |
| 文件： | 总16页 (文件大小：138K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
High Performance CMOS 5 x 7
Alphanumeric Displays
Technical Data
HCMS-29xx Series
Features
• Easy to Use
• Interfaces Directly with
Microprocessors
• 0.15" Character Height in 4,
8, and 16 (2x8) Character
Packages
Description
The HCMS-29xx series are high
performance, easy to use dot
matrix displays driven by on-board
CMOS ICs. Each display can be
directly interfaced with a
microprocessor, thus eliminating
the need for cumbersome interface
components. The serial IC
• 0.20" Character Height in 4
and 8 Character Packages
interface allows higher character
count information displays with a
minimum of data lines. A variety of
colors, font heights, and character
counts gives designers a wide
range of product choices for their
specific applications and the easy
to read 5 x 7 pixel format allows
the display of uppercase, lower
case, Katakana, and custom user-
defined characters. These displays
are stackable in the x- and y-
• Rugged X- and Y-Stackable
Package
• Serial Input
• Convenient Brightness
Controls
• Wave Solderable
• Offered in Five Colors
• Low Power CMOS
Technology
Applications
• Telecommunications
Equipment
• Portable Data Entry Devices
• Computer Peripherals
• Medical Equipment
• Test Equipment
• Business Machines
• Avionics
• TTL Compatible
directions, making them ideal for
high character count displays.
• Industrial Controls
Device Selection Guide
AlGaAs
HER
HCMS-
Orange
HCMS-
Yellow
HCMS-
Green
HCMS-
Package
Drawing
Description
HCMS-
2905
2915
2925
2965
2975
1 x 4 0.15" Character
1 x 8 0.15" Character
2 x 8 0.15" Character
1 x 4 0.20" Character
1 x 8 0.20" Character
2902
2912
2922
2962
2972
2904
2914
2924
2964
2974
2901
2911
2921
2961
2971
2903
2913
2923
2963
2973
A
B
C
D
E
ESD WARNING: STANDARD CMOS HANDLING PRECAUTIONS SHOULD BE OBSERVED TO
AVOID STATIC DISCHARGE.
2
17.78 (0.700) MAX.
PIN FUNCTION
ASSIGNMENT TABLE
PIN # FUNCTION
4.45 (0.175) TYP.
2.22 (0.087) SYM.
1
2
3
4
5
6
7
8
9
DATA OUT
OSC
V LED
DATA IN
RS
CLK
CE
12
1
1
2
3
4
BLANK
GND
3.71 (0.146) TYP.
10.16 (0.400) MAX.
10 SEL
11 V LOGIC
12 RESET
2.11 (0.083) TYP.
DATE CODE
PIN # 1 IDENTIFIER
LIGHT INTENSITY CATEGORY
COLOR BIN
COUNTRY OF ORIGIN
0.25
(0.010)
PART NUMBER
5.08
(0.200)
HCMS-290X X Z
YYWW
COO
4.32
(0.170)
TYP.
0.51 (0.020)
PIN # 1
2.54
SYM.
1.27
(0.050)
SYM.
(0.100)
2.54 ± 0.13
(0.100 ± 0.005)
(NON ACCUM.)
TYP.
7.62
(0.300)
0.51 ± 0.13
(0.020 ± 0.005)
TYP.
NOTES:
1. DIMENSIONS ARE IN mm (INCHES).
2. UNLESS OTHERWISE SPECIFIED, TOLERANCE ON DIMENSIONS IS ± 0.38 mm (0.015 INCH).
3. LEAD MATERIAL: SOLDER PLATED COPPER ALLOY.
HCMS-290x
35.56 (1.400) MAX.
2.22 (0.087) SYM.
4.45
(0.175)
TYP.
PIN FUNCTION
ASSIGNMENT TABLE
26
PIN # FUNCTION
3.71
(0.146)
10.16 (0.400) MAX.
TYP.
0
1
2
3
4
5
6
7
1
2
3
NO PIN
NO PIN
V LED
3
4
5
6
7
8
9
NO PIN
NO PIN
NO PIN
GND LED
NO PIN
NO PIN
V LED
NO PIN
NO PIN
NO PIN
DATA IN
RS
NO PIN
CLOCK
CE
BLANK
GND LOGIC
SEL
2.11 (0.083) TYP.
DATE CODE (YEAR, WEEK)
PIN # 1 IDENTIFIER
INTENSITY CATEGORY
COLOR BIN
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
PART NUMBER
COUNTRY OF ORIGIN
0.25
(0.010)
HCMS-291X
YYWW
X
Z
COO
5.08 (0.200)
0.51
(0.020)
4.32
(0.170)
TYP.
V LOGIC
NO PIN
RESET
OSC
2.54
SYM.
(0.100)
0.51 ± 0.13
(0.020 ± 0.005)
1.27
(0.050)
DATA OUT
TYP.
SYM.
2.54 ± 0.13
(0.100 ± 0.005)
(NON ACCUM.)
7.62
(0.300)
TYP.
NOTES:
1. DIMENSIONS ARE IN mm (INCHES).
2. UNLESS OTHERWISE SPECIFIED, TOLERANCE ON DIMENSIONS IS ± 0.38 mm (0.015 INCH).
3. LEAD MATERIAL: SOLDER PLATED COPPER ALLOY.
HCMS-291x
3
PIN FUNCTION ASSIGNMENT TABLE
PIN # FUNCTION PIN # FUNCTION
35.56 (1.400) MAX.
1B
2B
3B
4B
5B
6B
7B
8B
9B
NO PIN
NO PIN
V LED
NO PIN
NO PIN
NO PIN
GND LED
NO PIN
NO PIN
1A
2A
3A
4A
5A
6A
7A
8A
9A
NO PIN
NO PIN
V LED
NO PIN
NO PIN
NO PIN
GND LED
NO PIN
NO PIN
2.22 (0.088) SYM.
4.45 (0.175) MAX.
26B
26A
10B V LED
11B NO PIN
12B NO PIN
13B NO PIN
14B DATA IN
15B RS
16B NO PIN
17B CLOCK
18B CE
19B BLANK
20B GND LOGIC
21B SEL
22B V LOGIC
23B NO PIN
24B RESET
25B OSC
ROW B
10A V LED
11A NO PIN
12A NO PIN
13A NO PIN
14A DATA IN
15A RS
16A NO PIN
17A CLOCK
18A CE
19A BLANK
20A GND LOGIC
21A SEL
22A V LOGIC
23A NO PIN
24A RESET
25A OSC
0
8
1
9
2
3
4
5
6
7
4.83
(0.190)
3B
3A
19.81 (0.780) MAX.
9.65 (0.380)
10
11
12
13
14
15
3.71 (0.146) TYP.
ROW A
2.11 (0.083) TYP.
DATE CODE (YEAR, WEEK)
INTENSITY CATEGORY
PIN # 1 IDENTIFIER
26B DATA OUT
26A DATA OUT
COLOR BIN
PART NUMBER
COUNTRY OF ORIGIN
0.25
(0.010)
HCMS-292X
YYWW
X
Z
COO
5.08 (0.200)
0.51
(0.020)
2.54
SYM.
1.27
(0.050)
(0.100)
0.51 ± 0.13
(0.020 ± 0.005)
TYP.
2.03
(0.080)
2.54 ± 0.13
(0.100 ± 0.005)
(NON ACCUM.)
TYP.
7.62
(0.300)
NOTES:
1. DIMENSIONS ARE IN mm (INCHES).
2. UNLESS OTHERWISE SPECIFIED, TOLERANCE ON DIMENSIONS IS ± 0.38 mm (0.015 INCH).
3. LEAD MATERIAL: SOLDER PLATED COPPER ALLOY.
HCMS-292x
PIN FUNCTION
ASSIGNMENT TABLE
PIN # FUNCTION
21.46 (0.845) MAX.
1
2
DATA OUT
OSC
3
4
5
V LED
DATA IN
RS
2.67 (0.105) SYM.
2.54 (0.100) TYP.
6
7
CLK
CE
8
9
BLANK
GND
4.57
(0.180)
0
1
2
3
TYP.
10
11
12
SEL
V LOGIC
RESET
11.43 (0.450) MAX.
5.36 (0.211) TYP.
PIN # 1 IDENTIFIER
DATE CODE (YEAR, WEEK)
INTENSITY CATEGORY
COLOR BIN
PART NUMBER
0.25
(0.010)
COUNTRY OF ORIGIN
HCMS-296X
YYWW
X Z
COO
5.31
(0.209)
3.71
TYP.
(0.146)
0.50
(0.020)
0.169
SYM.
(4.28)
0.51 ± 0.13
(0.020 ± 0.005)
TYP.
0.072
(1.83)
SYM.
2.54 ± 0.13
TYP.
(0.100 ± 0.005)
7.62
(0.300)
NOTES:
1. DIMENSIONS ARE IN mm (INCHES).
2. UNLESS OTHERWISE SPECIFIED, THE TOLERANCE ON DIMENSIONS IS ± 0.38 mm (0.015 INCH).
3. LEAD MATERIAL: SOLDER PLATED COPPER ALLOY.
HCMS-296x
4
42.93 (1.690) MAX.
2.67 (0.105) SYM.
5.36 (0.211) TYP.
PIN FUNCTION
ASSIGNMENT TABLE
26
4.57
(0.180)
PIN # FUNCTION
1
2
3
4
5
6
7
8
TYP.
11.43 (0.450) MAX.
1
NO PIN
NO PIN
V LED
2
3
3
4
5
6
7
8
9
NO PIN
NO PIN
NO PIN
GND LED
NO PIN
NO PIN
V LED
NO PIN
NO PIN
NO PIN
DATA IN
RS
NO PIN
CLOCK
CE
BLANK
GND LOGIC
SEL
2.54 (0.100) TYP.
PIN # 1 IDENTIFIER
DATE CODE (YEAR, WEEK)
INTENSITY CATEGORY
COLOR BIN
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
0.25
(0.010)
PART NUMBER
COUNTRY OF ORIGIN
HCMS-297X
YYWW
5.31
(0.209)
X Z
COO
0.51
(0.020)
3.71
TYP.
(0.146)
V LOGIC
NO PIN
RESET
OSC
6.22
(0.245)
SYM.
0.51 ± 0.13
(0.020 ± 0.005)
TYP.
DATA OUT
1.90
(0.075)
SYM.
2.54 ± 0.13
(0.100 ± 0.005)
(NON ACCUM.)
TYP.
7.62
(0.300)
NOTES:
1. DIMENSIONS ARE IN mm (INCHES).
2. UNLESS OTHERWISE SPECIFIED, TOLERANCE ON DIMENSIONS IS ± 0.38 mm (0.015 INCH).
3. LEAD MATERIAL: SOLDER PLATED COPPER ALLOY.
HCMS-297x
Absolute Maximum Ratings
Logic Supply Voltage, VLOGIC to GNDLOGIC ....................... -0.3 V to 7.0 V
LED Supply Voltage, VLED to GNDLED .............................. -0.3 V to 5.5 V
Input Voltage, Any Pin to GND.......................... -0.3 V to VLOGIC +0.3 V
Free Air Operating Temperature Range T [1] .................. -40°C to +85°C
A
Relative Humidity (non-condensing) ............................................... 85%
Storage Temperature, TS ................................................. -55°C to 100°C
Wave Solder Temperature
1.59 mm (0.063 in.) below Body ...............................250°C for 3 secs
ESD Protection @ 1.5 kΩ, 100 pF (each pin) .............Class 1, 0-1999 V
TOTAL Package Power Dissipation at T = 25°C[2]
A
4 character ....................................................................... 1.2 W
8 character ....................................................................... 2.4 W
16 character ....................................................................... 4.8 W
Notes:
1. For operation in high ambient temperatures, see Appendix A, Thermal Considerations.
Recommended Operating Conditions Over Temperature Range
(-40°C to +85°C)
Parameter
Symbol
Min.
3.0
Typ.
5.0
5.0
0
Max.
Units
Logic Supply Voltage
LED Supply Voltage
GNDLED to GNDLOGIC
V
5.5
5.5
V
V
V
LOGIC
V
4.0
LED
–
-0.3
+0.3
5
Electrical Characteristics Over Operating Temperature Range (-40°C to +85°C)
TA = 25°C
-40°C < TA < 85°C
VLOGIC = 5.0 V
3.0 V < VLOGIC < 5.5 V
Parameter
Symbol
Typ.
Max.
Min.
Max.
Units
Test Conditions
IN = 0 V to VLOGIC
Input Leakage Current
II
µA
V
HCMS-290X/296X (4 char)
HCMS-291X/297X (8 char)
HCMS-292X (16 char)
+7.5
+15
+15
-2.5
-5.0
-5.0
+50
+100
+100
I
I
I
LOGIC OPERATING
ILOGIC(OPT)
ILOGIC(SLP)
ILED(BL)
ILED(SLP)
IPIXEL
mA
µA
VIN = V
LOGIC
HCMS-290X/296X (4 char)
HCMS-291X/297X (8 char)
HCMS-292X (16 char)
0.4
0.8
0.8
2.5
5
5
5
10
10
LOGIC SLEEP[1]
VIN = V
LOGIC
HCMS-290X/296X (4 char)
HCMS-291X/297X (8 char)
HCMS-292X (16 char)
5
10
10
15
30
30
25
50
50
LED BLANK
mA
µA
BL = 0 V
HMCS-290X/296X (4 char)
HCMS-291X/297X (8 char)
HCMS-292X (16 char)
2.0
4.0
4.0
4
8
8
4.0
8
8
ILED SLEEP[1]
HCMS-290X/296X (4 char)
HCMS 291X/297X (8 char)
HCMS-292X (16 char)
1
2
2
3
6
6
50
100
100
Peak Pixel Current[2]
VLED = 5.5 V
All pixels ON,
Average value per
pixel
HCMS-29X5 (AlGaAs)
HCMS-29XX (Other Colors)
15.4
14.0
17.1
15.9
18.7
17.1
mA
mA
HIGH level input voltage
V
ih
2.0
V
V
4.5 V < VLOGIC < 5.5 V
3.0 V < VLOGIC < 4.5 V
0.8 VLOGIC
LOW level input voltage
HIGH level output voltage
V
0.8
V
V
V
4.5 V < VLOGIC < 5.5 V
3.0 V < VLOGIC < 4.5 V
il
0.2 VLOGIC
V
oh
2.0
VLOGIC = 4.5 V,
Ioh = -40 µA
0.8 VLOGIC
V
V
3.0 V < VLOGIC < 4.5 V
LOW level output voltage
V
ol
0.4
VLOGIC = 5.5 V,
Iol = 1.6 mA[3]
0.2 VLOGIC
V
3.0 V < VLOGIC < 4.5 V
IC junction to pin
Thermal Resistance
RθJ-P
70
°C/W
Notes:
1. In SLEEP mode, the internal oscillator and reference current for LED drivers are off.
2. Average peak pixel current is measured at the maximum drive current set by Control Register 0. Individual pixels may exceed this
value.
3. For the Oscillator Output, Iol = 40 µA.
6
Optical Characteristics at 25°C[1]
VLED = 5.0 V, 50% Peak Current, 100% Pulse Width
Luminous Intensity
Peak
Wavelength
λPeak (nm)
Typ.
Dominant
Wavelength
λd[3] (nm)
Typ.
per LED[2]
CharacterAverage(µcd)
Display Color
AlGaAs Red
High Efficiency Red
Orange
Part Number
HCMS-29X5
HCMS-29X2
HCMS-29X4
HCMS-29X1
HCMS-29X3
Min.
Typ.
230
64
95
645
635
600
583
568
637
626
602
585
574
29
29
64
Yellow
29
64
Green
57
114
Notes:
1. Refers to the initial case temperature of the device immediately prior to measurement.
2. Measured with all LEDs illuminated.
3. Dominant wavelength, λd, is derived from the CIE chromaticity diagram and represents the single wavelength which defines the
perceived LED color.
Electrical Description
Pin Function
RESET (RST)
Description
Sets Control Register bits to logic low. The Dot Register contents are
unaffected by the Reset pin. (logic low = reset; logic high = normal
operation).
DATA IN (DIN)
DATA OUT (DOUT
CLOCK (CLK)
Serial Data input for Dot or Control Register data. Data is entered on the
rising edge of the Clock input.
)
Serial Data output for Dot or Control Register data. This pin is used for
cascading multiple displays.
Clock input for writing Dot or Control Register data. When Chip Enable is
logic low, data is entered on the rising Clock edge.
REGISTER SELECT (RS)
CHIP ENABLE (CE)
Selects Dot Register (RS = logic low) or Control Register (RS = logic high)
as the destination for serial data entry. The logic level of RS is latched on
the falling edge of the Chip Enable input.
This input must be a logic low to write data to the display. When CE
returns to logic high and CLK is logic low, data is latched to either the LED
output drivers or a Control Register.
OSCILLATOR SELECT
(SEL)
Selects either an internal or external display oscillator source.
(logic low = External Display Oscillator; logic high = Internal Display
Oscillator).
OSCILLATOR (OSC)
BLANK (BL)
Output for the Internal Display Oscillator (SEL = logic high) or input for an
External Display Oscillator (SEL = logic low).
Blanks the display when logic high. May be modulated for brightness
control.
GNDLED
GNDLOGIC
VLED
Ground for LED drivers.
Ground for logic.
Positive supply for LED drivers.
Positive supply for logic.
VLOGIC
7
AC Timing Characteristics Over Temperature Range (-40°C to +85°C)
Timing
Diagram
Ref.
4.5 V < VLOGIC <5.5 V
VLOGIC = 3 V
Number
Description
Symbol
Min.
Max.
Min.
Max.
Units
1
2
3
4
5
6
7
Register Select Setup Time to
Chip Enable
trss
10
10
ns
Register Select Hold Time to
Chip Enable
trsh
tclkce
tces
tceh
tds
10
20
35
20
10
10
10
10
20
55
20
10
10
10
ns
ns
ns
ns
ns
ns
Rising Clock Edge to Falling
Chip Enable Edge
Chip Enable Setup Time to
Rising Clock Edge
Chip Enable Hold Time to
Rising Clock Edge
Data Setup Time to Rising
Clock Edge
Data Hold Time after Rising
Clock Edge
tdh
[1]
8
9
Rising Clock Edge to DOUT
tdout
40
18
65
30
ns
ns
Propagation Delay DIN to DOUT
Simultaneous Mode for
one IC[1,2]
tdoutp
10
11
12
CE Falling Edge to DOUT Valid
Clock High Time
tcedo
tclkh
tclkl
trstl
25
45
ns
ns
80
80
50
100
100
50
Clock Low Time
ns
Reset Low Time
ns
Clock Frequency
F
5
4
MHz
KHz
cyc
Internal Display Oscillator
Frequency
F
80
210
80
210
inosc
Internal Refresh Frequency
F
150
410
150
400
Hz
rf
External Display Oscillator
Frequency
F
exosc
Prescaler = 1
Prescaler = 8
51.2
410
1000
8000
51.2
410
1000
8000
KHz
KHz
Notes:
1. Timing specifications increase 0.3 ns per pf of capacitive loading above 15 pF.
2. This parameter is valid for Simultaneous Mode data entry of the Control Register.
8
Display Overview
LEDs. Data is loaded into the Dot
Register according to the
procedure shown in Table 1 and
the Write Cycle Timing Diagram.
Reset
The HCMS-29xx series is a family
of LED displays driven by
on-board CMOS ICs. The LEDs
are configured as 5 x 7 font
characters and are driven in
groups of 4 characters per IC.
Each IC consists of a 160-bit shift
register (the Dot Register), two
7-bit Control Words, and refresh
circuitry. The Dot Register
contents are mapped on a
one-to-one basis to the display.
Thus, an individual Dot Register
bit uniquely controls a single
LED.
Reset initializes the Control
Registers (sets all Control
Register bits to logic low) and
places the display in the sleep
mode. The Reset pin should be
connected to the system power-on
reset circuit. The Dot Registers
are not cleared upon power-on or
by Reset. After power-on, the Dot
Register contents are random;
however, Reset will put the
display in sleep mode, thereby
blanking the LEDs. The Control
Register and the Control Words
are cleared to all zeros by Reset.
First RS is brought low, then CE
is brought low. Next, each
successive rising CLK edge will
shift in the data at the DIN pin.
Loading a logic high will turn the
corresponding LED on; a logic
low turns the LED off. When all
160 bits have been loaded (or 320
bits in an 8-digit display), CE is
brought to logic high.
When CLK is next brought to
logic low, new data is latched into
the display dot drivers. Loading
data into the Dot Register takes
place while the previous data is
displayed and eliminates the need
to blank the display while loading
data.
8-character displays have two ICs
that are cascaded. The Data Out
line of the first IC is internally
connected to the Data In line of
the second IC forming a 320-bit
Dot Register. The display’s other
control and power lines are
To operate the display after being
Reset, load the Dot Register with
logic lows. Then load Control
Word 0 with the desired bright-
ness level and set the sleep mode
bit to logic high.
connected directly to both ICs. In
16-character displays, each row
functions as an independent
8-character display with its own
320-bit Dot Register.
Pixel Map
In a 4-character display, the
160-bits are arranged as 20
Dot Register
The Dot Register holds the
pattern to be displayed by the
Table 1. Register Truth Table
Function
CLK
CE
RS
Select Dot Register
Not Rising
↓
L
Load Dot Register
DIN = HIGH LED = "ON"
DIN = LOW LED = "OFF"
↑
L
X
Copy Data from Dot Register to Dot Latch
Select Control Register
L
H
↓
X
H
X
X
Not Rising
Load Control Register[1][3]
↑
L
↑
Latch Data to Control Word[2]
L
Notes:
1. BIT D0 of Control Word 1 must have been previously set to Low for serial mode or High for simultaneous mode.
2. Selection of Control Word 1 or Control Word 0 is set by D7 of the Control Shift Register. The unselected control word retains its
previous value.
3. Control Word data is loaded Most Significant Bit (D7) first.
9
RS
CE
T
T
RSS
RSH
2
1
T
T
T
T
T
CLKL
12
CLKCE
3
CES
4
CEH
5
CLKH
11
CLK
[1]
T
T
T
NEW DATA LATCHED HERE
DS
6
DH
7
D
IN
T
CEDO
10
DOUT
8
D
(SERIAL)
OUT
T
DOUTP
9
D
OUT
(SIMULTANEOUS)
LED OUTPUTS,
CONTROL
PREVIOUS DATA
NEW DATA
REGISTERS
NOTE:
1. DATA IS COPIED TO THE CONTROL REGISTER OR THE DOT LATCH AND LED OUTPUTS WHEN CE IS HIGH AND CLK IS LOW.
HCMS-29xx Write Cycle Diagram
columns by 8 rows. This array can Control Register
logic high and then CE is brought
to logic low. Next, each
be conceptualized as four 5 x 8
dot matrix character locations,
but only 7 of the 8 rows have
LEDs (see Figures 1 & 2). The
bottom row (row 0) is not used.
Thus, latch location 0 is never
displayed. Column 0 controls the
left-most column. Data from Dot
Latch locations 0-7 determine
whether or not pixels in Column 0
are turned-on or turned-off.
Therefore, the lower left pixel is
turned-on when a logic high is
stored in Dot Latch location 1.
Characters are loaded in serially,
with the left-most character being
loaded first and the right-most
character being loaded last. By
loading one character at a time
and latching the data before
loading the next character, the
figures will appear to scroll from
right to left.
The Control Register allows
software modification of the IC’s
operation and consists of two
independent 7-bit control words.
Bit D7 in the shift register selects
one of the two 7-bit control
words. Control Word 0 performs
pulse width modulation
brightness control, peak pixel
current brightness control, and
sleep mode. Control Word 1 sets
serial/simultaneous data out
mode, and external oscillator
prescaler. Each function is
successive rising CLK edge will
shift in the data on the DIN pin.
Finally, when 8 bits have been
loaded, the CE line is brought to
logic high. When CLK goes to
logic low, new data is copied into
the selected control word.
Loading data into the Control
Register takes place while the
previous control word configures
the display.
Control Word 0
independent of the others.
Loading the Control Register with
D7 = Logic low selects Control
Word 0 (see Table 2). Bits D0-D3
adjust the display brightness by
pulse width modulating the LED
on-time, while Bits D4-D5 adjust
the display brightness by
changing the peak pixel current.
Bit D6 selects normal operation or
sleep mode.
Control Register Data
Loading
Data is loaded into the Control
Register, MSB first, according to
the procedure shown in Table 1
and the Write Cycle Timing
Diagram. First, RS is brought to
10
DATA OUT
RS (LATCHED)
H
L
DATA IN
CLK
L
H
H
L
SER/PAR
MODE
CHIP
ENABLE
DI
40 BIT
S.R.
DO
DI
40 BIT
S.R.
DO
DI
40 BIT
S.R.
DO
DI
40 BIT
S.R.
DO
DOT
REGISTERS
AND
DATA IN
CLR
CONTROL
REGISTER
DATA
OUT
LATCHES
REGISTER
SELECT
D
Q
RS
(LATCHED)
V LED +
CURRENT
REFERENCE
REFRESH
CONTROL
ANODE
CURRENT SOURCES
RESET
RST
PWM BRIGHTNESS
CONTROL
DOT
REGISTER
BIT # 159
PRESCALE
VALUE
ROW 7
H
L
÷8
OSC
ROW 1
0 x x x x
x x x x x
CHAR 1
x x x x x
CHAR 2
x x x x x ROW 0 (NO LEDS)
H
L
OSCILLATOR
COLUMN 0
CHAR 0
COLUMN 19
CHAR 3
L
H
OSC
SELECT
GND (LED)
BLANK
Figure 1.
DATA FROM
PREVIOUS
CHARACTER
PIXEL
DATA TO
NEXT
ROW 7
CHARACTER
ROW 6
ROW 5
ROW 4
ROW 3
ROW 2
ROW 1
ROW 0
(NOT USED)
Figure 2.
11
Sleep mode (Control Word 0, bit
D6 = Low) turns off the Internal
Display Oscillator and the LED
pixel drivers. This mode is used
when the IC needs to be powered
up, but does not need to be
same data in all Control Registers.
In the simultaneous mode, N ICs
only need 8 clock pulses to load
the same data in all Control
Registers. The propagation delay
from the first IC to the last is
right-most characters. The Dot
Registers are connected in series
to form a 320-bit dot shift
register. The location of pixel 0
has not changed. However, Dot
Shift Register bit 0 of IC2
active. Current draw in sleep
mode is nearly zero. Data in the
Dot Register and Control Words
are retained during sleep mode.
N * tDOUTP
.
becomes bit 160 of the 320-bit
dot shift register.
External Oscillator
Prescaler Bit D1
Bit D1 of Control Word 1 is used
to scale the frequency of an
The Control Registers of the two
ICs are independent of each
other. This means that to adjust
the display brightness the same
control word must be entered into
both ICs, unless the Control
Registers are set to simultaneous
mode.
Control Word 1
Loading the Control Register with
D7 = logic high selects Control
Word 1. This Control Word
performs two functions: serial/
simultaneous data out mode and
external oscillator prescale select
(see Table 2).
external Display Oscillator. When
this bit is logic low, the external
Display Oscillator directly sets the
internal display clock rate. When
this bit is a logic high, the
external oscillator is divided by 8.
This scaled frequency then sets
the internal display clock rate. It
takes 512 cycles of the display
clock (or 8 x 512 = 4096 cycles
of an external clock with the
divide by 8 prescaler) to com-
pletely refresh the display once.
Using the prescaler bit allows the
designer to use a higher external
oscillator frequency without extra
circuitry.
Longer character string systems
can be built by cascading multiple
displays together. This is
accomplished by creating a five
line bus. This bus consists of CE,
RS, BL, Reset, and CLK. The
display pins are connected to the
corresponding bus line. Thus, all
CE pins are connected to the CE
bus line. Similarly, bus lines for
RS, BL, Reset, and CLK are
created. Then DIN is connected to
the right-most display. DOUT from
this display is connected to the
next display. The left-most display
receives its DIN from the DOUT of
the display to its right. DOUT from
the left-most display is not used.
Serial/Simultaneous Data
Output D0
Bit D0 of control word 1 is used to
switch the mode of DOUT between
serial and simultaneous data entry
during Control Register writes.
The default mode (logic low) is
the serial DOUT mode. In serial
mode, DOUT is connected to the
last bit (D7) of the Control Shift
Register.
This bit has no affect on the
internal Display Oscillator
Frequency.
Storing a logic high to bit D0
changes DOUT to simultaneous
mode which affects the Control
Register only. In simultaneous
mode, DOUT is logically connected
to DIN. This arrangement allows
multiple ICs to have their Control
Registers written to simul-
Bits D2-D6
These bits must always be pro-
grammed to logic low.
Each display may be set to use its
internal oscillator, or the displays
may be synchronized by setting
up one display as the master and
the others as slaves. The slaves
are set to receive their oscillator
input from the master’s oscillator
output.
Cascaded ICs
Figure 3 shows how two ICs are
connected within an HCMS-29XX
display. The first IC controls the
four left-most characters and the
second IC controls the four
taneously. For example, for N ICs
in the serial mode, N * 8 clock
pulses are needed to load the
12
Table 2. Control Shift Register
CONTROL WORD 0
L
D6
D5
D4
D3
D2
D1
D0
↑
Bit D7
On-Time
Duty
Relative
Set Low
to Select
Control
Word 0
PWM Brightness
Control
Oscillator Factor Brightness
Cycles
(%)
(%)
L
L
L
L
L
L
L
H
L
0
1
0
0
1.7
3.3
5.0
6.7
8.3
11.7
15
0.2
0.4
0.6
0.8
1.0
1.4
1.8
2.1
2.7
3.5
4.3
5.5
7.0
9.4
11.7
L
L
H
H
L
2
L
L
H
L
3
L
H
H
H
H
L
4
L
L
H
L
5
L
H
H
L
7
L
H
L
9
H
H
H
H
H
H
H
H
11
14
18
22
28
36
48
60
18
L
L
H
L
23
L
H
H
L
30
L
H
L
37
H
H
H
H
47
L
H
L
60
H
H
80
H
100
Peak Current
Brightness
Control
Typical Peak
Pixel Current
(mA)
Relative Full
Scale Current
(Relative Brightness, %)
H
L
L
H
L
4.0
6.4
31
50
L
9.3
73 (Default at Power Up)
H
H
12.8
100
SLEEP MODE
L – DISABLES INTERNAL OSCILLATOR-DISPLAY BLANK
H – NORMAL OPERATION
CONTROL WORD 1
H
L
L
L
L
L
D1
D0
↑
Serial/Simultaneous Data Out
Bit D7
L – Dout holds contents of Bit D7
H – Dout is functionally tied to Din
Set High
to Select
Control
Word 1
Reserved for Future
Use (Bits D2-D6
must be set Low)
External Display Oscillator Prescaler
L – Oscillator Freq ÷ 1
H – Oscillator Freq ÷ 8
13
CE
RS
BL
RESET
CLK
CE
RS
BL
CE
RS
BL
RESET
CLK
RESET
CLK
IC1
BITS 0-159
CHARACTERS 0-3
IC2
BITS 160-319
CHARACTERS 4-7
D
D
D
IN
D
D
OUT
OUT
OUT
IN
OSC
SEL
SEL
SEL
OSC
OSC
D
IN
Figure 3. Cascaded ICs.
14
1.3
1.2
1.1
R
= 100°C/W
PD can be calculated as Equation
2 below.
θ
Appendix A. Thermal
Considerations
The display IC has a maximum
junction temperature of 150°C.
The IC junction temperature can
be calculated with Equation 1
below.
J-A
1.0
0.9
0.8
0.7
0.6
0.5
0.4
Figure 4 shows how to derate the
power of one IC versus ambient
temperature. Operation at high
ambient temperatures may
require the power per IC to be
reduced. The power consumption
can be reduced by changing
either the N, IPIXEL, Osc cyc or
0.3
0.2
A typical value for RθJA is 100°C/
W. This value is typical for a
display mounted in a socket and
covered with a plastic filter. The
socket is soldered to a .062 in.
thick PCB with .020 inch wide,
one ounce copper traces.
0.1
0
25 30 35 40 45 50 55 60 65 70 75 80 85 90
VLED. Changing VLOGIC has very
T
– AMBIENT TEMPERATURE – °C
A
little impact on the power
consumption.
Figure 4.
Appendix B. Electrical
Considerations
Current Calculations
Equation 1:
The peak and average display
current requirements have a
significant impact on power
supply selection. The maximum
peak current is calculated with
Equation 3 below.
TJMAX = TA + PD * RθJA
Where:
TJMAX = maximum IC junction temperature
TA = ambient temperature surrounding the display
RθJA = thermal resistance from the IC junction to ambient
PD = power dissipated by the IC
The average current required by
the display can be calculated with
Equation 4 below.
Equation 2:
PD = (N * IPIXEL * Duty Factor * VLED) + ILOGIC * VLOGIC
Where:
The power supply has to be able
to supply IPEAK transients and
supply ILED(AVG) continuously.
The range on VLED allows noise on
this supply without significantly
changing the display brightness.
PD = total power dissipation
N = number of pixels on (maximum 4 char * 5 * 7 = 140)
IPIXEL = peak pixel current.
Duty Factor = 1/8 * Osccyc/64
Osc cyc = number of ON oscillator cycles per row
ILOGIC = IC logic current
V
LOGIC = logic supply voltage
VLOGIC and VLED Considerations
The display uses two independent
electrical systems. One system is
used to power the display’s logic
and the other to power the
display’s LEDs. These two
systems keep the logic supply
clean.
Equation 3:
IPEAK = M * 20 * IPIXEL
Where:
IPEAK = maximum instantaneous peak current for the display
M = number of ICs in the system
20 = maximum number of LEDs on per IC
IPIXEL = peak current for one LED
Separate electrical systems allow
the voltage applied to VLED and
Equation 4:
VLOGIC to be varied independently.
Thus, VLED can vary from 0 to 5.5
V without affecting either the Dot
or the Control Registers. VLED can
ILED(AVG) = N * IPIXEL * 1/8 * (oscillator cycles)/64
(see Variable Definitions above)
15
be varied between 4.0 to 5.5 V
without any noticeable variation
in light output. However, operat-
ing VLED below 4.0 V may cause
objectionable mismatch between
the pixels and is not
Electrostatic Discharge
prescaler or 8 MHz with the
prescaler may cause noticeable
pixel to pixel mismatch.
The inputs to the ICs are pro-
tected against static discharge
and input current latchup. How-
ever, for best results, standard
CMOS handling precautions
should be used. Before use, the
HCMS-29XX should be stored in
antistatic tubes or in conductive
material. During assembly, a
grounded conductive work area
should be used and assembly
personnel should wear conductive
wrist straps. Lab coats made of
synthetic material should be
avoided since they are prone to
static buildup. Input current
latchup is caused when the CMOS
inputs are subjected to either a
Appendix D. Refresh
Circuitry
recommended. Dimming the
display by pulse width modulating
This display driver consists of 20
one-of-eight column decoders and
20 constant current sources, 1
one-of-eight row decoder and
eight row sinks, a pulse width
modulation control block, a peak
current control block, and the
circuit to refresh the LEDs. The
refresh counters and oscillator are
used to synchronize the columns
and rows.
VLED is also not recommended.
VLOGIC can vary from 3.0 to 5.5 V
without affecting either the
displayed message or the display
intensity. However, operation
below 4.5 V will change the
timing and logic levels and
operation below 3 V may cause
the Dot and Control Registers to
be altered.
The 160 bits are organized as 20
columns by 8 rows. The IC
illuminates the display by
voltage below ground (VIN
<
The logic ground is internally
connected to the LED ground by a
substrate diode. This diode
becomes forward biased and
conducts when the logic ground is
0.4 V greater then the LED
ground. The LED ground and the
logic ground should be connected
to a common ground which can
withstand the current introduced
by the switching LED drivers.
When separate ground
connections are used, the LED
ground can vary from -0.3 V to
+0.3 V with respect to the logic
ground. Voltages below -0.3 V can
cause all the dots to be ON.
Voltage above +0.3 V can cause
dimming and dot mismatch. The
LED ground for the LED drivers
can be routed separately from the
logic ground until an appropriate
ground plane is available. On long
interconnections between the
display and the host system,
voltage drops on the analog
ground) or to a voltage higher
then VLOGIC (VIN > VLOGIC) and
when a high current is forced into
the input. To prevent input
current latchup and ESD damage,
unused inputs should be con-
sequentially turning ON each of
the 8 row-drivers. To refresh the
display once takes 512 oscillator
cycles. Because there are eight
row drivers, each row driver is
selected for 64 (512/8) oscillator
cycles. Four cycles are used to
briefly blank the display before
the following row is switched on.
Thus, each row is ON for 60
oscillator cycles out of a possible
64. This corresponds to the
maximum LED on time.
nected to either ground or V
.
Voltages should not be appliLeOdGtICo
the inputs until VLOGIC has been
applied to the display.
Appendix C. Oscillator
The oscillator provides the
internal refresh circuitry with a
signal that is used to synchronize
the columns and rows. This
ensures that the right data is in
the dot drivers for that row. This
signal can be supplied from either
an external source or the internal
source.
Appendix E. Display
Brightness
Two ways have been shown to
control the brightness of this LED
display: setting the peak current
and setting the duty factor. Both
values are set in Control Word 0.
To compute the resulting display
brightness when both PWM and
peak current control are used,
simply multiply the two relative
brightness factors. For example,
if Control Register 0 holds the
word 1001101, the peak current
A display refresh rate of 100 Hz
or faster ensures flicker-free
operation. Thus for an external
oscillator the frequency should be
greater than or equal to 512 x
100 Hz = 51.2 kHz. Operation
above 1 MHz without the
ground can be kept from affecting
the display logic levels by
isolating the two grounds.
3.0
2.6
HER/ORANGE
YELLOW
2.2
1.8
1.4
GREEN
AlGaAs
1.0
0.6
0.2
-55 -35
-15
5
25
45
65
85
T
– AMBIENT TEMPERATURE – °C
A
Figure 5.
is 73% of full scale (BIT D5 = L,
BIT D4 = L) and the PWM is set
to 60% duty factor (BIT D3 = H,
BIT D2 = H, BIT D1 = L, BIT D0
= H). The resulting brightness is
44% (.73 x .60 = .44) of full
scale.
The temperature of the display
will also affect the LED brightness
as shown in Figure 5.
Appendix F. Reference
Material
Application Note 1027: Soldering
LED Components
Application Note 1015: Contrast
Enhancement Techniques for
LED Displays
www.agilent.com/semiconductors
For product information and a complete list of
distributors, please go to our web site.
For technical assistance call:
Americas/Canada: +1 (800) 235-0312 or
(916) 788-6763
Europe: +49 (0) 6441 92460
China: 10800 650 0017
Hong Kong: (+65) 6756 2394
India, Australia, New Zealand: (+65) 6755 1939
Japan: (+81 3) 3335-8152 (Domestic/Interna-
tional), or 0120-61-1280 (Domestic Only)
Korea: (+65) 6755 1989
Singapore, Malaysia, Vietnam, Thailand,
Philippines, Indonesia: (+65) 6755 2044
Taiwan: (+65) 6755 1843
Data subject to change.
Copyright © 2004 Agilent Technologies, Inc.
Obsoletes 5964-6376E
July 14, 2004
5988-4161EN
相关型号：
©2020 ICPDF网 联系我们和版权申明