HLMP-Q106 [AGILENT]
Subminiature High Performance TS AlGaAs Red LED Lamps; 超小型高性能TS的AlGaAs红色LED灯
| 型号： | HLMP-Q106 |
| 厂家： | 
AGILENT TECHNOLOGIES, LTD. |
| 描述： | Subminiature High Performance TS AlGaAs Red LED Lamps |
| 文件： | 总6页 (文件大小：120K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
H
Subminiature High
Performance TS AlGaAs Red
LED Lamps
Technical Data
HLMP-P106/P156
HLMP-Q10X/Q15X
Dome Packages
Features
The HLMP-QXXX Series dome
lamps, for use as indicators, use
a tinted, diffused lens to provide
a wide viewing angle with high
on-off contrast ratio. High
brightness lamps use an
untinted, nondiffused lens to
provide a high luminous inten-
sity within a narrow radiation
pattern.
• Subminiature Flat Top
Package
Ideal for Backlighting and
Light Piping Applications
• Subminiature Dome
Package
Diffused Dome for Wide
Viewing Angle
Non-diffused Dome for High
Brightness
• Wide Range of Drive
Currents
500 µA to 50 mA
• Ideal for Space Limited
Applications
• Axial Leads
• Available with lead
configurations for Surface
Mount and Through Hole
PC Board Mounting
Lead Configurations
Technology
All of these devices are made by
encapsulating LED chips on
axial lead frames to form
These subminiature solid state
lamps utilize a highly optimized
LED material technology,
molded epoxy subminiature
lamp packages. A variety of
package configuration options is
available. These include special
surface mount lead configura-
tions, gull wing, yoke lead, or Z-
bend. Right angle lead bends at
2.54 mm (0.100 inch) and 5.08
mm (0.200 inch) center spacing
are available for through hole
mounting. For more information
refer to Standard SMT and
Through Hole Lead Bend
transparent substrate
aluminum gallium arsenide (TS
AlGaAs). This LED technology
has a very high luminous
efficiency, capable of producing
high light output over a wide
range of drive currents (500 µA
to 50 mA). The color is deep red
at a dominant wavelength of
644 nm deep red. TS AlGaAs is
a flip-chip LED technology, die
attached to the anode lead and
wire bonded to the cathode lead.
Available viewing angles are
75°, 35°, and 15°.
Description
Flat Top Package
The HLMP-PXXX Series flat top
lamps use an untinted, non-
diffused, truncated lens to
provide a wide radiation pattern
that is necessary for use in
backlighting applications. The
flat top lamps are also ideal for
use as emitters in light pipe
applications.
Options for Subminiature LED
Lamps data sheet.
5964-9365E
1-168
Device Selection Guide
Viewing Angle
Deep Red Typical Iv Typical Iv Package
Package Description
2 θ1/2
Rd = 644 nm If = 500 µa If = 20 mA
Outline
Domed, Diffused Tinted,
Standard Current
35
35
15
15
75
75
HLMP-Q102
HLMP-Q152
HLMP-Q106
HLMP-Q156
HLMP-P106
HLMP-P156
160
530
130
B
Domed, Diffused Tinted,
Low Current
2
7
2
B
B
B
A
A
Domed, Nondiffused
Untinted, Standard Current
Domed, Nondiffused
Untinted, Low Current
Flat Top, Nondiffused,
Untinted, Standard Current
Flat Top, Nondiffused
Untinted, Low Current
Package Dimensions
A) Flat Top Lamps
1.40 (0.055)
1.65 (0.065)
0.50 (0.020) REF.
NOTE 3
ANODE
0.58 (0.023)
0.43 (0.017)
1.14 (0.045)
1.40 (0.055)
(0.460)
(0.420)
11.68
10.67
BOTH SIDES
1.91 (0.075)
2.41 (0.095)
0.76 (0.030) MAX.
0.46 (0.018)
0.56 (0.022)
CATHODE
CATHODE
STRIPE
NOTE 3
1.65 (0.065)
1.91 (0.075)
DIA.
0.25 (0.010) MAX.*
NOTE 2
(0.082)
(0.092)
2.08
2.34
0.18 (0.007)
0.23 (0.009)
(0.075)
(0.085)
1.91
2.16
0.20 (0.008) MAX.
* REFER TO FIGURE 1 FOR DESIGN CONCERNS.
B) Diffused and Nondiffused Dome Lamps
0.76 (0.030)
0.18 (0.007)
R.
0.89 (0.035)
0.23 (0.009)
0.94 (0.037)
1.24 (0.049)
2.03 (0.080)
2.92 (0.115)
1.78 (0.070)
MAX.
0.63 (0.025)
0.38 (0.015)
0.79 (0.031)
0.53 (0.021)
CATHODE
STRIPE
2.08 (0.082)
2.34 (0.092)
NOTE 3
1.91 (0.075)
2.16 (0.085)
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETRES (INCHES).
2. PROTRUDING SUPPORT TAB IS CONNECTED TO ANODE LEAD.
3. LEAD POLARITY FOR THESE TS AlGaAs SUBMINIATURE LAMPS IS OPPOSITE TO THE
LEAD POLARITY OF SUBMINIATURE LAMPS USING OTHER LED TECHNOLOGIES.
1-169
ANODE
TAB
NO. CATHODE DOWN.
YES. ANODE DOWN.
Figure 1. Proper Right Angle Mounting to a PC Board to Prevent
Protruding Anode Tab from Shorting to Cathode Connection.
Absolute Maximum Ratings at TA = 25°C
Peak Forward Current[2] ......................................................... 300 mA
Average Forward Current (@ IPEAK = 300 mA)[1,2].................... 30 mA
DC Forward Current[3] .............................................................. 50 mA
Power Dissipation ....................................................................100 mW
Reverse Voltage (IR = 100 µA) .........................................................5 V
Transient Forward Current (10 µs Pulse)[4] ........................... 500 mA
Operating Temperature Range ..................................... -55 to +100°C
Storage Temperature Range ..........................................-55 to +100°C
LED Junction Temperature ....................................................... 110°C
Lead Soldering Temperature
[1.6 mm (0.063 in.) from body ...........................260°C for 5 seconds
Reflow Soldering Temperatures
Convective IR.................. 235°C Peak, above 183°C for 90 seconds
Vapor Phase..................................................... 215°C for 3 minutes
Notes:
1. Maximum IAVG at f = 1 kHz, DF = 10%.
2. Refer to Figure 7 to establish pulsed operating conditions.
3. Derate linearly as shown in Figure 6.
4. The transient peak current is the maximum non-recurring peak current the
device can withstand without damaging the LED die and wire bonds. It is not
recommended that the device be operated at peak currents above the Absolute
Maximum Peak Forward Current.
1-170
Optical Characteristics at TA = 25°C
Luminous
Color,
Dominant
Viewing
Angle
Intensity
IV (mcd)
Total Flux
φV (mlm)
@ 20 mA[2]
Typ.
Peak
Luminous
Efficacy
ηv
(lm/w)
Part
Number
HLMP-
Wavelength Wavelength
2θ1/2
[5]
@ 20 mA[1]
Min. Typ.
λpeak (nm)
λd[3] (nm)
Degrees[4]
Typ.
Typ.
Typ.
Q106
Q102
P106
56
22
22
530
160
130
280
-
654
654
654
644
644
644
15
35
75
85
85
280
85
Optical Characteristics at TA = 25°C
Part
Number
(Low
Current)
HLMP-
Luminous
Intensity
IV (mcd)
Color,
Dominant
Viewing
Angle
Total Flux
Peak
Luminous
Efficacy
ηv
(lm/w)
φV (mlm)
Wavelength Wavelength
2θ1/2
[5]
@ 0.5 mA[1] @ 0.5 mA[2]
λpeak (nm)
λd[3] (nm)
Degrees[4]
Typ.
Min. Typ.
Typ.
10.5
-
Typ.
Typ.
Q156
Q152
P156
2.1
1.3
0.6
7
2
2
654
654
654
644
644
644
15
35
75
85
85
10.5
85
Notes:
1. The luminous intensity, Iv, is measured at the mechanical axis of the lamp package. The actual peak of the spatial radiation
pattern may not be aligned with this axis.
2. φv is the total luminous flux output as measured with an integrating sphere.
3. The dominant wavelength, λd, is derived from the CIE Chromaticity Diagram and represents the color of the device.
4. θ1/2 is the off-axis angle where the liminous intensity is 1/2 the peak intensity.
5. Radiant intensity, Iv, in watts/steradian, may be calculated from the equation Iv = Iv/ηv, where Iv is the luminous intensity in
candelas and ηv is the luminous efficacy in lumens/watt.
1-171
Electrical Characteristics at TA = 25°C
Forward
Voltage
VF (Volts)
@ IF = 20 mA
Typ. Max.
Reverse
Breakdown
VR (Volts)
@ IR = 100 µA
Min. Typ.
Capacitance
C (pF)
VF = 0,
f = 1 MHz
Typ.
Speed of Response
τs (ns)
Part
Number
HLMP-
Thermal
Resistance
RθJ-PIN (°C/W)
Time Constant
e-t/τ
s
Typ.
Q106
Q102
P106
1.9
1.9
1.9
2.4
2.4
2.4
5
5
5
20
20
20
20
20
20
170
170
170
45
45
45
Electrical Characteristics at TA = 25°C
Part
Number
(Low
Forward
Voltage
VF (Volts)
Reverse
Breakdown
VR (Volts)
Capacitance
C (pF)
VF = 0,
f = 1 MHz
Typ.
Speed of Response
τs (ns)
Thermal
Resistance
RθJ-PIN (°C/W)
Time Constant
e-t/τ
s
Current) @ IF = 0.5 mA @ IR = 100 µA
HLMP-
Typ. Max.
Min. Typ.
Typ.
Q156
1.6
1.6
1.6
1.9
1.9
1.9
5
5
5
20
20
20
20
20
20
170
170
170
45
Q152
45
P156
45
300
200
1.0
2.4
2.0
100
50
1.0
0.5
-1
10
20
10
0.2
0.1
-2
-3
10
5
0.05
2
1
10
0.01
0.5
500
600
700
1000
0
0.5
1.0
1.5
2.0
2.5
3.0 3.5
1
2
5
10
I – DC FORWARD CURRENT – mA
F
20
50
WAVELENGTH – nm
V
– FORWARD VOLTAGE – V
F
Figure 2. Relative Intensity vs.
Wavelength.
Figure 3. Forward Current vs.
Forward Voltage.
Figure 4. Relative Luminous
Intensity vs. DC Forward Current.
50
1.2
1.1
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
50
40
f > 1000 Hz
40
Rθ = 400° C/W
f > 300 Hz
30
JA
30
f > 100 Hz
20
Rθ = 550° C/W
JA
20
10
0
10
0
0.1
0.0
0
20
40
60
80
100
50
100
150
200
250
300
1
2
5
10 20
50 100 200 300
T
– AMBIENT TEMPERATURE – °C
I
– PEAK FORWARD CURRENT – mA
I
– PEAK FORWARD CURRENT – mA
A
PEAK
PEAK
Figure 6. Maximum Forward DC
Current vs. Ambient Temperature.
Derating Based on TJMAX = 110°C.
Figure 5. Relative Efficiency vs.
Peak Forward Current.
Figure 7. Maximum Average
Current vs. Peak Forward Current.
1-172
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
100° 90° 80° 70° 60° 50° 40° 30° 20° 10° 0° 10° 20° 30° 40° 50° 60° 70° 80° 90° 100°
ANGULAR DISPLACEMENT – DEGREES
Figure 8. HLMP-Q106/-Q156.
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
100° 90° 80° 70° 60° 50° 40° 30° 20° 10° 0° 10° 20° 30° 40° 50° 60° 70° 80° 90° 100°
ANGULAR DISPLACEMENT – DEGREES
Figure 9. HLMP-Q102/-Q152
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
100° 90° 80° 70° 60° 50° 40° 30° 20° 10° 0° 10° 20° 30° 40° 50° 60° 70° 80° 90° 100°
ANGULAR DISPLACEMENT – DEGREES
Figure 10. HLMP-P106/-P156.
1-173
相关型号：
©2020 ICPDF网 联系我们和版权申明