AM50E-2412SZ [AIMTEC]
DC-DC Converter;
| 型号： | AM50E-2412SZ |
| 厂家： | 
AIMTEC |
| 描述： | DC-DC Converter |
| 文件： | 总4页 (文件大小：438K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Click on Series name for product info on aimtec.com
Series AM50E-Z
50 Watt | DC-DC Converter
Picture coming soon
FEATURES:
• Wide 2:1 Input Range
• 1600 VDC Isolation
• Adjustable Output Voltage
• Continuous Short Circuit Protection
• Over Temperature Protection
•
•
•
•
•
Efficiency up to 92%
Remote On/Off Function
Over Current, Over Voltage Protection
Operating Temperature: -40°C to 85°C
Soft start
Models
Single output
Input Current
FL | NL
Output
Output
Current max
(A)
Maximum
Efficiency
Input
Voltage (V)
Model
Voltage
(V)
3.3
5
Capacitive load
(µF)
(%)
(mA)
AM50E-1203SZ
AM50E-1205SZ
AM50E-1212SZ
AM50E-1215SZ
AM50E-2403SZ
AM50E-2405SZ
AM50E-2412SZ
AM50E-2415SZ
AM50E-4803SZ
AM50E-4805SZ
AM50E-4812SZ
AM50E-4815SZ
9-18
9-18
9-18
3056
4682
4682
4682
1511
2290
2290
2290
756
110
200
60
60
70
90
40
40
50
60
40
40
10
10
4.167
3.333
10
26000
17000
3300
90
89
89
89
91
91
91
91
91
92
91
89
12
15
3.3
5
12
15
3.3
5
12
15
9-18
2200
18-36
18-36
18-36
18-36
36-75
36-75
36-75
36-75
26000
17000
3300
10
4.167
3.333
10
10
4.167
3.333
2200
26000
17000
2300
1132
1145
1170
2200
Add suffix “-K” for optional heat sink
NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at
rated output load unless otherwise specified.
Input Specifications
Parameters
Nominal
Typical
9-18
18-36
36-75
Maximum
Units
12
24
48
Voltage range
VDC
Filter
Startup time
π (Pi) Network
50
ms
VDC
ms
12
24
48
25
50
100
100
Absolute Maximum Rating
Peak Input Voltage time
On/Off control
ON: 3 ~12VDC or open circuit; OFF – 0 ~ 1.2VDC or Short circuit between pin 2 and pin 3
(OFF idle current: 5mA Typical)
12V ON/OFF
24V ON/OFF
48V ON/OFF
8.6 / 7.9
17.8 / 16
34 / 29
Under voltage lockout
VDC
Input Reflected Ripple Current
Transient Recovery time
Transient Response Deviation
20
250
mA p-p
µs
25% load step change
25% load step change
±3
%
Isolation Specifications
Parameters
Tested I/O voltage
Case/Input and Output
Resistance
Conditions
60 sec
Typical
Rated
1600
1600
Units
VDC
VDC
MOhm
pF
60 sec
<1000
2000
Capacitance
www.aimtec.com
F 051e R1
Tel: +1 514 620 2722
1 of 4
Toll free: + 1 888 9 AIMTEC (924 6832)
North America only
Series AM50E-Z
50 Watt | DC-DC Converter
Output Specifications
Parameters
Voltage accuracy
Conditions
Typical
±1
Maximum
Units
%
Over voltage protection
Over load protection
Zener diode clamp
120~140
% of Iout
Short Circuit protection
Line voltage regulation
Load voltage regulation
Temperature coefficient
Ripple & Noise*
Continuous, auto-restart
HL-LL
0% to 100% load
±0.5
±0.5
%
%
%/oC
mV p-p
%
±0.02
20MHz Bandwidth
100
±10
Voltage adjustment range
*Measured with a 1µF ceramic capacitor.
General Specifications
Parameters
Conditions
Typical
230
270
Maximum
Units
100% load, 12Vin models
100% load, 24 & 48Vin models
See derating chart
Switching frequency
KHz
Operating temperature
Storage temperature
Maximum case temperature
Over Temperature Protection
Cooling
-40 to +85
oC
oC
oC
oC
-40 to +125
105
115
Measured on the case
Free Air Convection (30-65 LFM)
Humidity
Case material
Weight
95
% RH
g
Copper
45
Dimensions (L x W x H)
MTBF
Maximum soldering temperature
2.00 x 1.00 x 0.45 inches
>200,000 hrs (MIL-HDBK -217F, Ground Benign, t=+25ºC) hours
1.5mm from case for 10 sec 260
50.80 x 25.40 x 11.50 mm
oC
Safety Specifications
Parameters
Agency Approval
CE, cULus
EN55032, Class A
IEC 61000-4-2, Criteria A
IEC 61000-4-3, Criteria A
IEC 61000-4-4, Criteria A, with external filter
IEC 61000-4-5, Criteria A, with external filter
IEC 61000-4-6, Criteria A
IEC 61000-4-8, Criteria A
Designed to meet IEC 60950-1
Safety
Pin Out Specifications
Pin
1
Dimensions
50.80
(2.00)
Single
+ V Input
- V Input
5.08
(0.20)
2
3
4
5
6
On/Off Control
+ V Output
-V Output
Trim
4
1
2
Bottom View
5
3
6
2.54
2.54
(0.10)
(0.10)
Notes:
All dimensions are typical in millimeters (inches).
Pin Pitch and Length Tolerance: ±0.35 (±0.014)
Pin Diameter: ±0.05 (±0.002)
Case Tolerance ±0.50 (±0.02)
Stand-off Tolerance: ±0.10 (±0.004)
ᴓ1.00
(0.04)
www.aimtec.com
F 051e R1
Tel: +1 514 620 2722
2 of 4
Toll free: + 1 888 9 AIMTEC (924 6832)
North America only
Series AM50E-Z
50 Watt | DC-DC Converter
Dimensions with Optional Heatsink
50.8
(2.0)
25.4
(1.0)
16.3
(0.64)
SIDE
END
Notes: Add “-K” suffix for ordering, heat sink is affixed with thermally dissipative adhesive tape.
See derating graph for temperature performance. Heat sink material is anodized (black) aluminum, adds weight 11.2g.
Thermal impedance of converter is: with heat sink 10°C/W and 12°C/W without heat sink.
Trimming
Derating
Free Air Convection
º
C without heat sink
50
100
º
C with heat sink
56
80
75
Safe Operating Area
60
50
40
20
0
56
60
50
70
95
85
80
100
-40
-20
0
20
40
º C
Ambient Temperature
Extended temperature performance can be achieved with optional heat sink. (add suffix “–K” to part number)
Input Reflected Ripple Current Test Step
Lin
Current Probe
+V output
+
+V input
DC/DC
Cin
Converter
Load
DC Power Source
-
-V input
-V output
Input reflected ripple current is measured through a source inductor Lin(12uH) and a source capacitor Cin (47uF, ESR<1.0ohm at
100KHz) at a nominal input and full load
www.aimtec.com
F 051e R1
Tel: +1 514 620 2722
3 of 4
Toll free: + 1 888 9 AIMTEC (924 6832)
North America only
Series AM50E-Z
50 Watt | DC-DC Converter
Output Ripple and noise reduction
+V output
+
+V input
DC/DC
Converter
Cin
Cout
Load
DC Power Source
10uF
1uF
10uF
-
-V input
-V output
To reduce ripple and noise, it is recommended to use a 1µF ceramic disk capacitor and a 10µF electrolytic
Control ON/OFF pin connection example
+V input
+V output
-V output
DC/DC
Converter
On/Off
Control
-V input
EFT/Surge Circuit recommendation
+Vout
+Vin
DC/DC
Converter
Load
C1
Vin
24V
48V
C1
-Vin
220 µF / 100V
-Vout
NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled
by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the
date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%,
nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components
and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This
product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate
specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com.
www.aimtec.com
F 051e R1
Tel: +1 514 620 2722
4 of 4
Toll free: + 1 888 9 AIMTEC (924 6832)
North America only
相关型号：
AM50E-4815S-NZ
DC/DC Converter; Product Weight (grams): 35; Input voltage min (V): 36; Input voltage max (V): 75; Output voltage min: 15; Output voltage max: 15; Output voltage dual assymetric (y/n): Single; Output Power (W): 50; Max Output current (A): 3.333; Efficiency (%): 93; Max Capacitive load (µF): 2000; Package type: 2x1; Mounting: PCB; W (in): 1; L (in): 2; H (in): 0.46; W (mm): 25.4; L (mm): 50.8; H (mm): 11.8; Min Operating temperature: -40; Max operating temperature (°C): 85; Isolation (VDC): 1500; EMC compliance 2: EN 55022 Class B; Case material: Aluminum; Application 4 (building automation/Io
AIMTEC
©2020 ICPDF网 联系我们和版权申明