AMEPR50N-42105Z [AIMTEC]
up to 1150mA | AC-DC LED driver;型号: | AMEPR50N-42105Z |
厂家: | AIMTEC |
描述: | up to 1150mA | AC-DC LED driver |
文件: | 总6页 (文件大小:549K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Series AMEPR50N-Z
up to 1150mA | AC-DC LED driver
FEATURES:
• Universal Input: 90~264 Vac
• High Efficiency: Up to 87%
• Active Power Factor Correction
• Short Circuit / Open Circuit Protection
•
Meet UL, CE Safety Requirement
Long Life, High reliability
Ultra-low ripple without flickering
3-year limited warranty
•
•
•
Models
Single output
Max Output
Power (W)
42.0
Output Voltage
Range (V)
30-42
Output Current
(mA)
1000
1050
1150
Input Voltage
(VAC/Hz)
90-264/47-63
90-264/47-63
90-264/47-63
Efficiency
Model
(%)
87.0
87.0
87.0
AMEPR50N-42100Z
AMEPR50N-42105Z
AMEPR50N-42115Z
44.1
48.3
30-42
30-42
NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity <75%, nominal input voltage and at
rated output load unless otherwise specified.
Input Specifications
Parameters
Conditions
Typical
Maximum
0.76
40
60
0.75
1.5
Units
Arms
90 VAC, full load
115 VAC, cold start
230 VAC, cold start
Input Current
Inrush current <2ms
Leakage current
Input dissipation
A
mA
W
W
No Load
Output Short
4.5
115 VAC, full load
230 VAC, full load
0.98
0.95
Power Factor
Input Fuse
2A/250V
115 VAC, full load
230 VAC, full load
1.5
1.0
Sec.
Sec.
Start-up Time
Output Specifications
Parameters
Current accuracy
Line regulation
Conditions
Typical
Maximum
Units
%
%
±5
±3
±5
LL to HL
Full Output Voltage Range
Load regulation
%
Ripple & Noise
Output Current Ripple
200
50
mV p-p
mA
Full load
LL to HL, full load at cold start,
% of rated output current
Current Overshoot
15
%
Hold-up time (min)
0.5
ms
Minimum Load Voltage
See Models Table Above
Isolation Specifications
Parameters
Tested I/O voltage
Isolation Resistance
Isolation Capacitance
Conditions
I/P – O/P
500Vdc
Typical
Rated
3750
Units
VAC
MΩ
>100
100
pF
General Specifications
Parameters
Switching frequency
Over voltage protection
Short circuit protection
Short circuit restart
Conditions
Typical
Maximum
Units
KHz
V
150
50
Continuous, Hiccup Mode
Auto Recovery
Open circuit protection
Continuous, Hiccup Mode
www.aimtec.com
F 052.1e R1
Tel: +1 514 620 2722
1 of 6
Toll free: + 1 888 9 AIMTEC (924 6832)
North America only
Series AMEPR50N-Z
up to 1150mA | AC-DC LED driver
Operating temperature
Maximum case temperature
Storage temperature
Temperature coefficient
Cooling
Humidity
Case material
IP Rating
Weight
Without Derating
-40 to +50
90
-40 to +85
oC
oC
oC
0.03
90
% / oC
Free Air Convection
% RH
g
Plastic
IP54
260
Dimensions (L X W+ X H)
MTBF
6.30 X 1.73 X 1.61 inches
160.00 X 44.00 X 41.00 mm
300,000 hrs (MIL-HDBK-217F at +25°C)
Safety Specifications
Parameters
Electromagnetic Interference
Harmonic Current Emissions
EN55015 / FCC Part 15, Class B
EN61000-3-2, Class B
EN61000-3-3
EN61000-4-2, 8kV Air, 4kV Contact, Level 3, Criteria A
EN61000-4-3, Test-RS Level 3, Criteria A
EN61000-4-4, Burst EFT Level 3, Criteria A
EN61000-4-5, Line to Neutral 4kV, Neutral to FG 6kV
EN61000-4-6. Test-CS Level 3, Criteria A
EN61000-4-8, Test 3A/m, Criteria A
Voltage fluctuations and flicker
Electrostatic Discharge Immunity
RF, Electromagnetic Field Immunity
Electrical Fast Transient / Burst Immunity
Surge Immunity
RF, Conducted Disturbance Immunity
Power frequency Magnetic Field Immunity
Voltage dips, Short Interruptions Immunity
Standards
EN61000-4-11, Criteria B
Electromagnetic Immunity Requirements Applies EN61547
to Lighting Equipment
Pin Definition
Pin
Specification / Termination
AC-N
AC-L
LED+
LED-
Blue Color, Wire Gauge #18
Brown Color, Wire Gauge #18
The central pin of DC5521 Plug, Connected to the internal red wire
The external Cylinder pin of DC5521 Plug , Connected to internal black wire
Block diagram
LED+
LED-
AC1
AC2
1st LED
LED
LED
AC
www.aimtec.com
F 052.1e R1
Tel: +1 514 620 2722
2 of 6
Toll free: + 1 888 9 AIMTEC (924 6832)
North America only
Series AMEPR50N-Z
up to 1150mA | AC-DC LED driver
Dimensions
Top View
147.5
5.81
15±5
0.59±0.20
106.0
4.17
180±10
7.09±0.39
10.0
0.39
4.0
0.16
10±1
0.39±0.04
5±1
0.20±0.04
44.0
1.73
DC5521
32.0
1.26
AWM E355456 STYLE
2464 18AWG VW-ISO
80°C 300V
32±2
1.26±0.08
105±5
4.13±0.20
160.0
6.30
Side View
Black
Red
41.0
1.61
2.10(0.08)
5.45(0.21)
Efficiency Vs. Input Voltage & Output Load Voltage
AMEPR50N-42100Z
95.00%
90.00%
85.00%
80.00%
75.00%
70.00%
65.00%
115VAC
230VAC
30
33
36
39
42
Output Voltage(V)
www.aimtec.com
F 052.1e R1
Tel: +1 514 620 2722
3 of 6
Toll free: + 1 888 9 AIMTEC (924 6832)
North America only
Series AMEPR50N-Z
up to 1150mA | AC-DC LED driver
AMEPR50N-42105Z
95.00%
90.00%
85.00%
80.00%
75.00%
70.00%
115VAC
230VAC
65.00%
30
33
36
39
42
Output Voltage(V)
AMEPR50N-42115Z
95.00%
90.00%
85.00%
80.00%
115VAC
230VAC
75.00%
70.00%
65.00%
30
33
36
39
42
Output Voltage(V)
www.aimtec.com
F 052.1e R1
Tel: +1 514 620 2722
4 of 6
Toll free: + 1 888 9 AIMTEC (924 6832)
North America only
Series AMEPR50N-Z
up to 1150mA | AC-DC LED driver
PF vs. Input Voltage & Output Load Voltage
AMEPR50N-42100Z
1.200
0.900
0.600
0.300
0.000
115VAC
230VAC
30
33
36
39
42
Output Voltage(V)
AMEPR50N-42105Z
1.200
0.900
0.600
0.300
115VAC
230VAC
0.000
30
33
36
39
42
Output Voltage(V)
www.aimtec.com
F 052.1e R1
Tel: +1 514 620 2722
5 of 6
Toll free: + 1 888 9 AIMTEC (924 6832)
North America only
Series AMEPR50N-Z
up to 1150mA | AC-DC LED driver
AMEPR50N-42115Z
1.200
0.900
0.600
0.300
115VAC
230VAC
0.000
30
33
36
39
42
Output Voltage(V)
NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled
by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the
date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%,
nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components
and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This
product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate
specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com.
www.aimtec.com
F 052.1e R1
Tel: +1 514 620 2722
6 of 6
Toll free: + 1 888 9 AIMTEC (924 6832)
North America only
相关型号:
AMEPR60-24250AZ-NA
AC/DC LED Driver; Product Weight (grams): 530; Input voltage min (V): 90; Input voltage max (V): 305; Input frequency (Hz): 47-440; Output voltage min: 12; Output voltage max: 24; Output voltage dual assymetric (y/n): Single; Output Power (W): 60; Max Output current (A): 2.5; Efficiency (%): 87; Package type: Encapsulated; Rating (IP): IP68; Mounting: Wire terminal; W (in): 2.27; L (in): 5.3; H (in): 1.59; W (mm): 57.68; L (mm): 134.8; H (mm): 40.5; Min Operating temperature: -40; Max operating temperature (°C): 85; Isolation (VAC): 3000; EMC compliance 1: EN 55022 Class B; Case material: Pla
AIMTEC
AMEPR60-36170AZ-NA
AC/DC LED Driver; Product Weight (grams): 530; Input voltage min (V): 90; Input voltage max (V): 305; Input frequency (Hz): 47-440; Output voltage min: 24; Output voltage max: 36; Output voltage dual assymetric (y/n): Single; Output Power (W): 60; Max Output current (A): 1.66; Efficiency (%): 88; Package type: Encapsulated; Rating (IP): IP68; Mounting: Wire terminal; W (in): 2.27; L (in): 5.3; H (in): 1.59; W (mm): 57.68; L (mm): 134.8; H (mm): 40.5; Min Operating temperature: -40; Max operating temperature (°C): 85; Isolation (VAC): 3000; EMC compliance 1: EN 55022 Class B; Case material: Pl
AIMTEC
AMEPR60-50120AZ-NA
AC/DC LED Driver; Product Weight (grams): 530; Input voltage min (V): 90; Input voltage max (V): 305; Input frequency (Hz): 47-440; Output voltage min: 36; Output voltage max: 50; Output voltage dual assymetric (y/n): Single; Output Power (W): 60; Max Output current (A): 1.2; Efficiency (%): 89; Package type: Encapsulated; Rating (IP): IP68; Mounting: Wire terminal; W (in): 2.27; L (in): 5.3; H (in): 1.59; W (mm): 57.68; L (mm): 134.8; H (mm): 40.5; Min Operating temperature: -40; Max operating temperature (°C): 85; Isolation (VAC): 3000; EMC compliance 1: EN 55022 Class B; Case material: Pla
AIMTEC
AMEPR60C-12500AZ
AC/DC LED Driver; Product Weight (grams): 530; Input voltage min (V): 90; Input voltage max (V): 305; Input frequency (Hz): 47-440; Output voltage min: 5; Output voltage max: 12; Output voltage dual assymetric (y/n): Single; Output Power (W): 60; Max Output current (A): 0-5.2; Efficiency (%): 80; Package type: Encapsulated; Rating (IP): IP68; Mounting: Wire terminal; W (in): 1.59; L (in): 5.3; H (in): 2.27; W (mm): 40.5; L (mm): 134.8; H (mm): 57.68; Min Operating temperature: -40; Max operating temperature (°C): 85; Isolation (VAC): 3000; EMC compliance 1: EN 55022 Class B; Case material: Pl
AIMTEC
AMEPR60C-12500AZ-NA
AC/DC LED Driver; Product Weight (grams): 530; Input voltage min (V): 90; Input voltage max (V): 305; Input frequency (Hz): 47-440; Output voltage min: 5; Output voltage max: 12; Output voltage dual assymetric (y/n): Single; Output Power (W): 60; Max Output current (A): 0-5.2; Efficiency (%): 80; Package type: Encapsulated; Rating (IP): IP68; Mounting: Wire terminal; W (in): 1.59; L (in): 5.3; H (in): 2.27; W (mm): 40.5; L (mm): 134.8; H (mm): 57.68; Min Operating temperature: -40; Max operating temperature (°C): 85; Isolation (VAC): 3000; EMC compliance 1: EN 55022 Class B; Case material: Pl
AIMTEC
©2020 ICPDF网 联系我们和版权申明