AP1150ADS18 [AKM]
14V Input / 200mA Output LDO Regulator;型号: | AP1150ADS18 |
厂家: | ASAHI KASEI MICROSYSTEMS |
描述: | 14V Input / 200mA Output LDO Regulator |
文件: | 总20页 (文件大小:720K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
[AP1150ADSXX]
AP1150ADSXX
14V Input / 200mA Output LDO Regulator
1. Genaral Description
The AP1150ADSxx is a low dropout linear regulator with ON/OFF control, which can supply 200mA load
current. The IC is an integrated circuit with a silicon monolithic bipolar structure. The output voltage, trimmed
with high accuracy, is available from 1.3 to 9.5V in 0.1V steps.
The output capacitor is available to use a small 0.1uF ceramic capacitor (1.8VVout). The over current, thermal
and reverse bias protections are integrated, and also the package is small and thin type. The IC is designed for
space saving requirements.
2.Feature
Available to use a small 0.1uF ceramic capacitor (1.8VVOUT
)
Dropout Voltage
VDROP=120mV at 100mA
High Precision output voltage
High ripple rejection ratio
Wide operating voltage range
Very low quiescent current
On/Off control (High active)
1.5% or 50mV
80dB at 1kHz
2.1V to 14V
IQ=63A at Iout=0mA
Built-in Short circuit protection,thermal shutdown
Built-in reverse bias over current protection
Available very low noise application
Very small surface mount package
SOT23-5
3.Application
Any Electronic Equipment
Battery Powered Systems
Mobile Communication
014011331-E-00
- 1 -
2014/10
[AP1150ADSXX]
4.Table of Contents
1. Genaral Description ........................................................................................................................................... 1
2. Feature................................................................................................................................................................ 1
3. Application......................................................................................................................................................... 1
4. Table of Contents............................................................................................................................................... 2
5. Block Diagram................................................................................................................................................... 3
6. Ordering Information......................................................................................................................................... 4
7. Pin Configurations and Functions...................................................................................................................... 5
■ Pin Configurations............................................................................................................................................ 5
■ Functions .......................................................................................................................................................... 5
8. Absolute Maximum Ratings .............................................................................................................................. 6
9. Recommended Operating Conditions................................................................................................................ 6
10.
Electrical Characteristics................................................................................................................................ 7
■ Electrical Characteristics of Ta=Tj=25C ........................................................................................................ 7
■ Electrical Characteristics of Ta=-40C~85℃................................................................................................... 9
11.
Description................................................................................................................................................... 11
11.1 DC Characteristics.................................................................................................................................... 11
11.2 Input / output capacitors........................................................................................................................... 11
11.3 Bias voltage and temperature characteristics of the ceramic capacitor .................................................... 13
11.4 On/off control........................................................................................................................................... 13
11.5 Noise Bypass............................................................................................................................................ 13
11.6 Board Layout............................................................................................................................................ 14
12.
13.
Definition of term......................................................................................................................................... 16
Recommended External Circuits.................................................................................................................. 17
■External Circuit ............................................................................................................................................... 17
■Test Circuit...................................................................................................................................................... 17
14.
Package ........................................................................................................................................................ 18
■ Outline Dimensions........................................................................................................................................ 18
15.
Revise History.............................................................................................................................................. 19
IMPORTANT NOTICE.......................................................................................................................................... 20
014011331-E-00
- 2 -
2014/10
[AP1150ADSXX]
5.Block Diagram
Figure 1. Block Diagram
014011331-E-00
- 3 -
2014/10
[AP1150ADSXX]
6.Ordering Information
AP1150ADSXX
Ta = -40 to 85°C
SOT23-5
・ Output Voltage Code
For product name, please check the below chart. Please contact your authorized ASAHI KASEI
MICRODEVICES representative for voltage availability.
AP1150ADSXX
Output voltage code
Table 1. Standard Voltage Version, Output Voltage & Voltage Code
XX
VOUT
XX
VOUT
XX
VOUT
15
18
30
1.5
1.8
3.0
33
40
45
3.3
4.0
4.5
50
54
-
5.0
5.4
-
Table 2. Optional Voltage Version, Output Voltage & Voltage Code
XX
VOUT
XX
VOUT
XX
VOUT
XX
VOUT
13
14
16
17
19
20
21
22
23
24
25
26
1.3
1.4
1.6
1.7
1.9
2.0
2.1
2.2
2.3
2.4
2.5
2.6
27
28
29
31
32
34
35
36
37
38
39
41
2.7
2.8
2.9
3.1
3.2
3.4
3.5
3.6
3.7
3.8
3.9
4.1
42
43
44
46
47
48
49
51
52
53
55
60
4.2
4.3
4.4
4.6
4.7
4.8
4.9
5.1
5.2
5.3
5.5
6.0
65
70
75
80
85
90
95
-
-
-
-
-
6.5
7.0
7.5
8.0
8.5
9.0
9.5
-
-
-
-
-
014011331-E-00
- 4 -
2014/10
[AP1150ADSXX]
7.Pin Configurations and Functions
■ Pin Configurations
5
1
4
3
(Top View)
2
■ Functions
Pin
Pin No.
Internal Equivalent Circuit
Description
Description
Vcont
1
On/Off Control Terminal
320k
500k
1
VCONT
The pull-down resister (500k) is built-in.
2
3
GND
Np
GND Terminal
Np
3
Noise Bypass Terminal
Connect a bypass capacitor between GND.
Vout
Vin
4
4
5
VOUT
Output Terminal
Input Terminal
Vref
VIN
014011331-E-00
- 5 -
2014/10
[AP1150ADSXX]
Condition
8.Absolute Maximum Ratings
Parameter
Supply Voltage
Symbol
VccMAX
min
-0.4
-0.4
-0.4
-0.4
-0.4
-
max
16
6
Unit
V
V
Vout≦2.0V
Reverse Bias
VrevMAX
12
5
V
2.1V≦Vout
Np Terminal Voltage
Vcont Terminal Voltage
Junction temperature
VnpMAX
VcontMAX
Tj
V
16
150
150
V
℃
C
Storage Temperature Range
Tstg
-55
When mounted on PCB
(Note 1)
Power Dissipation
PD
-
500
mW
Note 1. Please do derating with 4.0mW/C at Pd=500mW and 25C or more. Thermal resistance (JA) =
250C/W.
WARNING: The maximum ratings are the absolute limitation values with the possibility of the IC breakage.
When the operation exceeds this standard quality cannot be guaranteed.
9.Recommended Operating Conditions
Parameter
Symbol
min
typ
max
Unit
Condition
Operating Temperature Range
Operating Voltage Range
Ta
-40
2.1
-
-
85
14
C
V
VOP
014011331-E-00
- 6 -
2014/10
[AP1150ADSXX]
10. Electrical Characteristics
■ Electrical Characteristics of Ta=Tj=25C
The parameters with min or max values will be guaranteed at Ta=Tj=25C.
(VIN=Vout(typ)+1V,Vcont=1.8V,Ta=Tj=25C)
Parameter
Output Voltage
Symbol
Vout
Condition
Iout = 5mA
min
typ
max
Unit
(Table 3,Table 4)
0.0
V
Line Regulation
LinReg
-
5.0
mV
mV
mV
mV
mV
VIN = 5V
Iout = 5mA ~ 100mA
Iout = 5mA ~ 200mA
Iout = 50mA
Load Regulation
LoaReg
(Table 3,Table 4)
-
-
80
140
210
Iout = 100mA
120
Iout = 180mA
Dropout Voltage (Note 2)
Vdrop
-
230
350
mV
(2.1V≦Vout≦2.3V)
Iout = 200mA
-
200
320
350
-
mV
mA
(2.4V≦Vout)
Maximum Output Current
(Note 3)
IoutMAX
240
Vout=Vout(typ)0.9
Short Circuit Current(Note 3)
Quiescent Current
ISHORT
Iq
-
-
-
-
360
63
-
mA
A
A
mA
Iout = 0mA
100
0.1
1.8
Standby Current
Istandby Vcont = 0V
0.0
1.0
Ground Terminal Current
Vcont Terminal
Ignd
Iout = 50mA
Vcont Terminal Current
Icont
Vcont = 1.8V
Vout ON state
Vout OFF state
-
1.8
-
5.0
15.0
-
A
V
-
-
Vcont Terminal Voltage
Vcont
0.35
V
Note 2. For Vout 2.0V, no regulations.
Note 3. The maximum output current is limited by power dissipation.
Table 3. Standard Voltage Version
Output Voltage
Load Regulation
Iout = 100mA Iout = 200mA
typ max
Part Number
min
typ
max
typ
max
V
V
V
V
V
mV
21
22
26
27
29
31
33
34
V
AP1150ADS15
AP1150ADS18
AP1150ADS30
AP1150ADS33
AP1150ADS40
AP1150ADS45
AP1150ADS50
AP1150ADS54
1.450
1.750
2.950
3.250
3.940
4.432
4.925
5.319
1.500
1.800
3.000
3.300
4.000
4.500
5.000
5.400
1.550
1.850
3.050
3.350
4.060
4.568
5.075
5.481
10
10
11
12
13
13
14
14
23
24
27
28
30
31
32
33
49
51
61
64
69
73
78
81
014011331-E-00
- 7 -
2014/10
[AP1150ADSXX]
Table 4. Optional Voltage Version
Output Voltage
Load Regulation
Iout = 100mA Iout = 200mA
typ max typ max
Part Number
min
typ
max
V
V
V
V
V
mV
20
20
21
21
22
22
23
23
23
24
24
24
25
25
25
26
26
27
27
28
28
29
29
30
30
30
31
31
32
32
32
33
33
34
34
36
38
39
41
43
44
46
48
V
47
48
50
51
52
53
54
55
55
56
57
58
59
60
60
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
86
90
94
98
102
106
110
114
AP1150ADS13
AP1150ADS14
AP1150ADS16
AP1150ADS17
AP1150ADS19
AP1150ADS20
AP1150ADS21
AP1150ADS22
AP1150ADS23
AP1150ADS24
AP1150ADS25
AP1150ADS26
AP1150ADS27
AP1150ADS28
AP1150ADS29
AP1150ADS31
AP1150ADS32
AP1150ADS34
AP1150ADS35
AP1150ADS36
AP1150ADS37
AP1150ADS38
AP1150ADS39
AP1150ADS41
AP1150ADS42
AP1150ADS43
AP1150ADS44
AP1150ADS46
AP1150ADS47
AP1150ADS48
AP1150ADS49
AP1150ADS51
AP1150ADS52
AP1150ADS53
AP1150ADS55
AP1150ADS60
AP1150ADS65
AP1150ADS70
AP1150ADS75
AP1150ADS80
AP1150ADS85
AP1150ADS90
AP1150ADS95
1.250
1.350
1.550
1.650
1.850
1.950
2.050
2.150
2.250
2.350
2.450
2.550
2.650
2.750
2.850
3.050
3.150
3.349
3.447
3.546
3.644
3.743
3.841
4.038
4.137
4.235
4.334
4.531
4.629
4.728
4.826
5.023
5.122
5.220
5.319
5.910
6.402
6.895
7.387
7.880
8.372
8.865
9.357
1.300
1.400
1.600
1.700
1.900
2.000
2.100
2.200
2.300
2.400
2.500
2.600
2.700
2.800
2.900
3.100
3.200
3.400
3.500
3.600
3.700
3.800
3.900
4.100
4.200
4.300
4.400
4.600
4.700
4.800
4.900
5.100
5.200
5.300
5.400
6.000
6.500
7.000
7.500
8.000
8.500
9.000
9.500
1.350
1.450
1.650
1.750
1.950
2.050
2.150
2.250
2.350
2.450
2.550
2.650
2.750
2.850
2.950
3.150
3.250
3.451
3.553
3.654
3.756
3.857
3.959
4.162
4.263
4.365
4.466
4.669
4.771
4.872
4.974
5.177
5.278
5.380
5.481
6.090
6.598
7.105
7.613
8.120
8.628
9.136
9.643
10
10
10
10
10
10
10
11
11
11
11
11
11
11
11
12
12
12
12
12
12
12
12
13
13
13
13
13
13
14
14
14
14
14
14
15
15
16
17
17
18
18
19
22
22
23
23
24
24
24
25
25
25
25
26
26
26
27
27
27
28
28
28
29
29
29
30
30
30
31
31
31
32
32
33
33
33
33
35
36
38
39
40
42
43
45
014011331-E-00
- 8 -
2014/10
[AP1150ADSXX]
■ Electrical Characteristics of Ta=-40C~85℃
The parameters with min or max values will be guaranteed at Ta=-40 ~ 85C.
(VIN=Vout(typ)+1V,Vcont=1.8V,Ta=-40~85C)
Parameter
Output Voltage
Symbol
Vout
Condition
min
typ
max
Unit
Iout = 5mA
(Table 5,Table 6)
0.0
V
Line Regulation
LinReg
-
8.0
mV
mV
mV
mV
mV
VIN = 5V
Iout = 5mA ~ 100mA
Iout = 5mA ~ 200mA
Iout = 50mA
Load Regulation
LoaReg
(Table 5,Table 6)
-
-
80
180
270
Iout = 100mA
120
Iout = 180mA
-
230
390
mV
Dropout Voltage (Note 4)
Vdrop
(2.2V≦Vout≦2.3V)
Iout = 200mA
-
200
320
390
-
mV
mA
(2.4V≦Vout)
Maximum Output Current (Note
5)
IoutMAX
220
Vout=Vout(typ) 0.9
Short Circuit Current (Note 5)
Quiescent Current
ISHORT
Iq
-
-
-
-
360
63
-
mA
μA
Iout = 0mA
120
0.5
2.2
Standby Current
Istandby Vcont = 0V
0.0
1.0
μA
Ground Terminal Current
Vcont Terminal
Ignd
Iout = 50mA
mA
Vcont Terminal Current
Icont
Vcont = 1.8V
Vout ON state
Vout OFF state
-
1.8
-
5.0
15.0
-
μA
V
-
-
Vcont Terminal Voltage
Vcont
0.35
V
Note 4. For Vout 2.1V, no regulations.
Note 5. The maximum output current is limited by power dissipation.
Table 5. Standard Voltage Version
Output Voltage
Load Regulation
Iout = 100mA Iout = 200mA
typ max
Part Number
min
typ
max
typ
max
V
V
V
V
V
mV
21
22
26
27
29
31
33
34
V
AP1150ADS15
AP1150ADS18
AP1150ADS30
AP1150ADS33
AP1150ADS40
AP1150ADS45
AP1150ADS50
AP1150ADS54
1.420
1.720
2.920
3.217
3.900
4.387
4.875
5.265
1.500
1.800
3.000
3.300
4.000
4.500
5.000
5.400
1.580
1.880
3.080
3.383
4.100
4.613
5.125
5.535
10
10
11
12
13
13
14
14
27
28
32
33
36
38
40
41
63
63
83
88
100
109
117
124
014011331-E-00
- 9 -
2014/10
[AP1150ADSXX]
Table 6. Optional Voltage Version
Output Voltage
Load Regulation
Iout = 100mA Iout = 200mA
typ max typ max
Part Number
min
typ
max
V
V
V
V
V
mV
20
20
21
21
22
22
23
23
23
24
24
24
25
25
25
26
26
27
27
28
28
29
29
30
30
30
31
31
32
32
32
33
33
34
34
36
38
39
41
43
44
46
48
V
AP1150ADS13
AP1150ADS14
AP1150ADS16
AP1150ADS17
AP1150ADS19
AP1150ADS20
AP1150ADS21
AP1150ADS22
AP1150ADS23
AP1150ADS24
AP1150ADS25
AP1150ADS26
AP1150ADS27
AP1150ADS28
AP1150ADS29
AP1150ADS31
AP1150ADS32
AP1150ADS34
AP1150ADS35
AP1150ADS36
AP1150ADS37
AP1150ADS38
AP1150ADS39
AP1150ADS41
AP1150ADS42
AP1150ADS43
AP1150ADS44
AP1150ADS46
AP1150ADS47
AP1150ADS48
AP1150ADS49
AP1150ADS51
AP1150ADS52
AP1150ADS53
AP1150ADS55
AP1150ADS60
AP1150ADS65
AP1150ADS70
AP1150ADS75
AP1150ADS80
AP1150ADS85
AP1150ADS90
AP1150ADS95
1.220
1.320
1.520
1.620
1.820
1.920
2.020
2.120
2.220
2.320
2.420
2.520
2.620
2.720
2.820
3.020
3.120
3.315
3.412
3.510
3.607
3.705
3.802
3.997
4.095
4.192
4.290
4.485
4.582
4.680
4.777
4.972
5.070
5.167
5.265
5.850
6.337
6.825
7.312
7.800
8.287
8.775
9.262
1.300
1.400
1.600
1.700
1.900
2.000
2.100
2.200
2.300
2.400
2.500
2.600
2.700
2.800
2.900
3.100
3.200
3.400
3.500
3.600
3.700
3.800
3.900
4.100
4.200
4.300
4.400
4.600
4.700
4.800
4.900
5.100
5.200
5.300
5.400
6.000
6.500
7.000
7.500
8.000
8.500
9.000
9.500
1.380
1.480
1.680
1.780
1.980
2.080
2.180
2.280
2.380
2.480
2.580
2.680
2.780
2.880
2.980
3.180
3.280
3.485
3.588
3.690
3.793
3.895
3.998
4.203
4.305
4.408
4.510
4.715
4.818
4.920
5.023
5.228
5.330
5.433
5.535
6.150
6.663
7.175
7.688
8.200
8.713
9.225
9.738
10
10
10
10
10
10
10
11
11
11
11
11
11
11
11
12
12
12
12
12
12
12
12
13
13
13
13
13
13
14
14
14
14
14
14
15
15
16
17
17
18
18
19
26
26
27
28
28
29
29
29
30
30
30
31
31
32
32
33
33
34
34
34
35
35
36
36
37
37
37
38
38
39
39
40
40
41
41
43
45
47
49
50
52
54
56
60
61
65
61
65
66
68
70
72
73
75
77
78
80
82
85
87
90
92
93
95
97
99
102
104
105
107
110
112
114
115
119
120
122
124
134
142
151
159
168
176
185
193
014011331-E-00
- 10 -
2014/10
[AP1150ADSXX]
11. Description
11.1 DC Characteristics
Line Regulation
Load Regulation
15
10
5
10
5
±0
VOUT=2.0V
VOUT=3.0V
±0
-5
-5
-10
-15
-20
-25
-30
-35
-40
-10
VOUT=1.5V
-15
VOUT=5.0V
2.0V
3.0V
4.0V
5.0V
-20
-25
-30
-35
0
5
10
15
20
0
50
100
150
200
VIN(V)
IOUT(mA)
Stability Point
Dropout Voltage versus Output Current
IOUT=0 to 200mA
20
IOUT=0mA
±0
±0
-20
-20
-40
-60
-80
-40
-60
-80
-100
-120
-140
-160
-180
-200
-100
-120
-140
-160
-180
-200
IOUT=200mA
IOUT in 50mA steps
-100
0
100
200
300
0
100
200
VIN(mV)
IOUT(mA)
11.2 Input / output capacitors
Linear regulators require input and output capacitors in order to maintain the regulator's loop stability. The
equivalent series resistance (ESR) of the output capacitor must be in the stable operation area. However, it is
recommended to use as large a value of capacitance as is practical. The output noise and the ripple noise
decrease as the capacitance value increases. ESR values vary widely between ceramic and tantalum capacitors.
However, tantalum capacitors are assumed to provide more ESR damping resistance, which provides greater
circuit stability. This implies that a higher level of circuit stability can be obtained by using tantalum capacitors
when compared to ceramic capacitors with similar values.
For output voltage device 2.0V applications, the recommended value of CL0.10F.
For output voltage device 1.5V applications, the recommended value of CL0.22F
014011331-E-00
- 11 -
2014/10
[AP1150ADSXX]
The input capacitor is necessary when the battery is discharged, the power supply impedance increases, or
the line distance to the power supply is long. This capacitor might be necessary on each individual IC even if
two or more regulator ICs are used. It is not possible to determine this indiscriminately. Please confirm the
stability while mounted. The IC provides stable operation with an output side capacitor of
0.1F (Vout2.0V). If it is 0.1F or more over the full range of temperature, either a ceramic capacitor or
tantalum capacitor can be used without considering ESR.
CIN=0.22 to
CL=0.22 to
0.1F
0.1F
CNP=0.01F
Figure 2. Recommended components values
VOUT=1.5 to 1.9V
VOUT=2.0V
VOUT=3.0V
VOUT=4.0V
VOUT=5.0V
100
100
10
100
10
100
10
100
10
Stable area
CL=0.1F
Stable area
CL=0.068
Stable area
CL=0.068F
Stable area
CL=0.068F
Stable area
CL=0.068F
F
10
1
1
1
1
1
0.1
0.1
0.1
0.1
0.1
0.01
0.01
0.01
0.01
0.01
0
50
100 150
0
50
100 150
0
50
100 150
0
50
100 150
0
50
100 150
IOUT(mA)
IOUT(mA)
IOUT(mA)
IOUT(mA)
IOUT(mA)
All stable: CL0.22F All stable: CL0.1F
Figure 3. Stable operation area vs. voltage, current, and ESR
Note 6. Please increase the output capacitor value when the load current is 0.5 mA or less. The stability of the
regulator improves if a big output side capacitor is used (the stable operation area extends.)
014011331-E-00
- 12 -
2014/10
[AP1150ADSXX]
11.3 Bias voltage and temperature characteristics of the ceramic capacitor
Generally, a ceramic capacitor has both a temperature characteristic and a voltage characteristic. Please
consider both characteristics when selecting the part. The B curves are the recommend characteristics.
Capacitance versus Voltage
Capacitance versus Ambinet Temperature
100
90
100
90
B Curve
B Curve
80
80
70
70
F Curve
F Curve
60
60
50
40
50
40
0
2
4
6
8
10
12
-50 -25
0
25
50
75 100
Bias Voltage(V)
Ambinet Temperature(°C)
11.4 On/off control
It is recommended to turn the regulator off when the circuit following the regulator is non-operating. A design
with little electric power loss can be implemented. We recommend the use of the on/off control of the
regulator without using a high side switch to provide an output from the regulator. A highly accurate output
voltage with low voltage drop is obtained. Because the Vcont terminal current is small, it is possible to control
it directly by CMOS logic.
Vsat
REG
On/Off Cont.
Figure 4. Equivalent circuit of output
11.5 Noise Bypass
The noise and the ripple rejection characteristics depend on the capacitance on the Np terminal. The ripple
rejection characteristic of the low frequency region improves by increasing the capacitance of Cnp. A standard
value is Cnp=0.001F. Increase Cnp in a design with important output noise and ripple rejection requirements.
The IC will not be damaged if the capacitor value is increased. The on/off switching speed changes depending
on the Np terminal capacitance. The switching speed slows when the capacitance is large.
014011331-E-00
- 13 -
2014/10
[AP1150ADSXX]
11.6Board Layout
VIN
Vout
on/off
Np
Figure 5. Layout(PCB Material: Glass epoxy (t=0.8mm))
Pd(mW)
500
-4.0mW/C
0
0
25 50
100
(85C)
150C
Figure 6. Derating curve
Please do derating with 4.0mW/C at Pd=500mW and 25C or more. Thermal resistance (ja) is=250C/W.
The package loss is limited at the temperature that the internal temperature sensor works (about 150C).
Therefore, the package loss is assumed to be an internal limitation. There is no heat radiation characteristic of
the package unit assumed because of the small size. The device being mounted on the PCB carries heat away.
This value changes by the material and the copper pattern etc. of the PCB. The losses are approximately
500mW. Enduring these losses becomes possible in a lot of applications operating at 25C.
The overheating protection circuit operates when there are a lot of losses with the regulator (When outside
temperature is high or heat radiation is bad). The output current cannot be pulled enough and the output
voltage will drop when the protection circuit operates. When the junction temperature reaches 150C, the IC is
shut down. However, operation begins at once when the IC stops operation and the temperature of the chip
decreases.
・How to determine the thermal resistance when mounted on PCB
The thermal resistance when mounted is expressed as follows:
Tj=jaPd+Ta
Tj of IC is set around 150C. Pd is the value when the thermal sensor is activated.
If the ambient temperature is 25C, then:
150=jaPd+25
ja=125/Pd (C /mW)
014011331-E-00
- 14 -
2014/10
[AP1150ADSXX]
・The simple method to calculate Pd
Mount the IC on the print circuit board. Short between the output terminal and ground. after that, raise input
voltage from 0V to evaluated voltage gradually. At shorted the output terminal, the power dissipation PD can
be expressed as Pd=VIN Iin. The input current decreases gradually as the temperature of the chip becomes
high. After a while, it reaches the thermal equilibrium. Use this currrent value at the thermal equilibrium. In
almost all the cases, it shows 500mW or more. In the case that the power, VIN Short Circuit Current, becomes
more than twice of the maximum rating of its power dissipation in a moment, there is a possibility that the IC
is destroyed before internal thermal protection works.
Procedure (When mounted on PCB.)
1. Find Pd (VINIin when the output side is
short-circuited).
Pd(mW)
Pd
2
2. Plot Pd against 25C.
3. Connect Pd to the point corresponding to the 150C
with a straight line.
D Pd
5
4. In design, take a vertical line from the maximum
operating temperature (e.g., 75C) to the derating curve.
5. Read off the value of Pd against the point at which the
vertical line intersects the derating curve. This is taken
as the maximum power dissipation DPd.
6. DPd (VINmaxVout)=Iout (at 75C)
3
4
0
25
50
75
Ta (℃)
100
150
Figure 7. Determine Pd
The maximum output current at the highest operating temperature will be Iout DPd (VINMaxVout).
Please use the device at low temperature with better radiation. The lower temperature provides better quality.
014011331-E-00
- 15 -
2014/10
[AP1150ADSXX]
12. Definition of term
・Output Voltage (Vout)
The output voltage is specified with VIN=Vout(typ)+1V , and Iout=5mA.
・Maximum Output Current (IoutMAX
)
The rated output current is specified under the condition where the output voltage drops 0.3V the value specified
with Iout=5mA. The input voltage is set to Vout(typ)+1V and the current is pulsed to minimize temperature effect.
・Dropout Voltage (Vdrop)
The dropout voltage is the difference between the input voltage and the output voltage at which point the regulator
starts to fall out of regulation. Below this value, the output voltage will fall as the input voltage is reduced. It is
dependent upon the load current and the junction temperature.
・Line Regulation (LinReg)
Line regulation is the ability of the regulator to maintain a constant output voltage as the input voltage changes. The
line regulation is specified as the input voltage is changed from VIN=Vout(typ)+1V to VIN= Vout(typ)+6V. It is a
pulse measurement to minimize temperature effect.
・Load Regulation (LoaReg)
Load regulation is the ability of the regulator to maintain a constant output voltage as the load current changes. It is
a pulsed measurement to minimize temperature effects with the input voltage set to VIN=Vout(typ)+1V. The load
regulation is specified output current step conditions of
5mA to 100mA.
・Ripple Rejection (R.R)
Ripple rejection is the ability of the regulator to attenuate the ripple content of the input voltage at the output.
It is specified with 200mVrms, 1kHz super-imposed on the input voltage, where VIN=Vout+1.5V. Ripple
rejection is the ratio of the ripple content of the output vs. input and is expressed in dB.
・Standby Current (Istandby)
Standby current is the current, which flows into the regulator when the output is turned off by the control function
(Vcont=0V).
・Over Current Sensor
The over current sensor protects the device when there is excessive output current. It also protects the device if the
output is accidentally connected to ground.
・Thermal Sensor
The thermal sensor protects the device in case the junction temperature exceeds the safe value (TJ=150C). This
temperature rise can be caused by external heat, excessive power dissipation caused by large input to output voltage
drops, or excessive output current. The regulator will shut off when the temperature exceeds the safe value. As the
junction temperatures decrease, the regulator will begin to operate again. Under sustained fault conditions, the
regulator output will oscillate as the device turns off then resets. Damage may occur to the device under extreme
fault.
Please reduce the loss of the regulator when this protection operate, by reducing the input voltage or make better heat
efficiency.In the case that the power, VIN Ishort(Short Circuit Current), becomes more than twice of the maximum
rating of its power dissipation in a moment, there is a possibility that the IC is destroyed before internal thermal
protection works.
・Reverse Voltage Protection
Reverse voltage protection prevents damage due to the output voltage being higher than the input voltage. This fault
condition can occur when the output capacitor remains charged and the input is reduced to zero, or when an external
voltage higher than the input voltage is applied to the output side
VIN
Vout
GND
014011331-E-00
- 16 -
2014/10
[AP1150ADSXX]
13. Recommended External Circuits
■External Circuit
To load
5
4
VIN
Vout
Cin
0.22F
CL
F
VIN
Vcont GND
Np
3
1
2
Cnp
0.01F
Vcont
Figure 8. External Circuit
■Test Circuit
5
4
Iin
A
VIN
Vout
V
Cin
1.0F
Icont
CL
Iout
Vout
IN
+
+
V
Vcont GND
Np
3
1.0F
1
2
A
Cnp
Vcont
0.001F
Figure 9. Test Circuit
Note 7. Electrical Characteristics are applied for the test circuit above.
(Cin=1.0F(Tantalum) ,CL=1.0F(Tantalum) , Cnp=0.001F(Ceramic))In the application , both of
ceramic capacitor and tantalum capacitor are available to use as Cin , CL and Cnp at Iout 0.5mA.
014011331-E-00
- 17 -
2014/10
[AP1150ADSXX]
14. Package
■ Outline Dimensions
・Unit: mm
Mark
4
Lot No.
5
R33
xxx
1
3
+
0.1
0.4
0.95
0.95
+
0.2
2.9
+
0.2
0.4
+0.2
0.3
2.8
014011331-E-00
- 18 -
2014/10
[AP1150ADSXX]
15. Revise History
Date
(YY/MM/DD)
14/10/29
Revision
00
Page
-
Contents
First Edition
014011331-E-00
- 19 -
2014/10
[AP1150ADSXX]
IMPORTANT NOTICE
0. Asahi Kasei Microdevices Corporation (“AKM”) reserves the right to make changes to the
information contained in th
1. is document without notice. When you consider any use or application of AKM product stipulated in
this document (“Product”), please make inquiries the sales office of AKM or authorized distributors
as to current status of the Products.
1. All information included in this document are provided only to illustrate the operation and
application examples of AKM Products. AKM neither makes warranties or representations with
respect to the accuracy or completeness of the information contained in this document nor grants any
license to any intellectual property rights or any other rights of AKM or any third party with respect
to the information in this document. You are fully responsible for use of such information contained
in this document in your product design or applications. AKM ASSUMES NO LIABILITY FOR
ANY LOSSES INCURRED BY YOU OR THIRD PARTIES ARISING FROM THE USE OF
SUCH INFORMATION IN YOUR PRODUCT DESIGN OR APPLICATIONS.
2. The Product is neither intended nor warranted for use in equipment or systems that require
extraordinarily high levels of quality and/or reliability and/or a malfunction or failure of which may
cause loss of human life, bodily injury, serious property damage or serious public impact, including
but not limited to, equipment used in nuclear facilities, equipment used in the aerospace industry,
medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic
signaling equipment, equipment used to control combustions or explosions, safety devices, elevators
and escalators, devices related to electric power, and equipment used in finance-related fields. Do
not use Product for the above use unless specifically agreed by AKM in writing.
3. Though AKM works continually to improve the Product’s quality and reliability, you are
responsible for complying with safety standards and for providing adequate designs and safeguards
for your hardware, software and systems which minimize risk and avoid situations in which a
malfunction or failure of the Product could cause loss of human life, bodily injury or damage to
property, including data loss or corruption.
4. Do not use or otherwise make available the Product or related technology or any information
contained in this document for any military purposes, including without limitation, for the design,
development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or
missile technology products (mass destruction weapons). When exporting the Products or related
technology or any information contained in this document, you should comply with the applicable
export control laws and regulations and follow the procedures required by such laws and
regulations. The Products and related technology may not be used for or incorporated into any
products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or
foreign laws or regulations.
5. Please contact AKM sales representative for details as to environmental matters such as the RoHS
compatibility of the Product. Please use the Product in compliance with all applicable laws and
regulations that regulate the inclusion or use of controlled substances, including without limitation,
the EU RoHS Directive. AKM assumes no liability for damages or losses occurring as a result of
noncompliance with applicable laws and regulations.
6. Resale of the Product with provisions different from the statement and/or technical features set forth
in this document shall immediately void any warranty granted by AKM for the Product and shall not
create or extend in any manner whatsoever, any liability of AKM.
7. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior
written consent of AKM.
014011331-E-00
- 20 -
2014/10
相关型号:
©2020 ICPDF网 联系我们和版权申明