TK63430AMFGH-L-C [AKM]
Fixed Positive LDO Regulator;型号: | TK63430AMFGH-L-C |
厂家: | ASAHI KASEI MICROSYSTEMS |
描述: | Fixed Positive LDO Regulator 输出元件 调节器 |
文件: | 总29页 (文件大小:603K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
[TK634xxAMF]
TK634xxAMF
Auto Discharge, Ultra Small Package, High RR, Fast Response, Low Noise
200mA CMOS LDO Regulator IC
1-. DESCRIPTION
4-. PIN CONFIGURATION
The TK634xxAMF is a CMOS LDO regulator with auto
discharge function. The package is the very small and
thin HSON1214-4.
The IC is designed for portable applications with space
requirements.
The IC can supply 200mA output current.
The IC does not require a noise-bypass capacitor.
The output voltage is internally fixed from 1.5V to 4.2V.
HSON1214-4
VOut
1
2
4
3
VIn
GND
VCont
(Top View)
2-. FEATURES
Auto discharge function
Package: HSON1214-4
No noise bypass capacitor required
High ripple rejection
Fast transient response
Low noise
5-. BLOCK DIAGRAM
VOut
1
VIn
4
Thermal and over current protection
High maximum load current
On/Off control
VRef
COut
CIn
High accuracy
Thermal &
Over Current
Protection
On/Off
Control
3-. APPLICATIONS
VCont
GND
2
3
Mobile communication
Battery powered system
Any electronic equipment
AP-MS0036-E-00
- 1 -
2011/02
[TK634xxAMF]
6-. ORDERING INFORMATION
T K 6 3 4
A
G H L - C
Voltage Code
(Refer to the following table)
Operating Temp. Range Code
C : C Rank(standard)
Package Code
MF : HSON1214-4
Tape/Reel Code
L : Left type
Solder Composion Code
GH : PB Free & Halogen Free
Output Voltage
Voltage Code
Output Voltage
Voltage Code
Output Voltage
Voltage Code
1.5V
15
2.85V
01
3.5V
35
1.8V
2.5V
2.6V
2.7V
2.8V
18
25
26
27
28
2.9V
3.0V
3.1V
3.2V
3.3V
29
30
31
32
33
4.0V
40
*If you need a voltage other than the value listed in the above table, please contact Asahi Kasei Microdevices.
7-. ABSOLUTE MAXIMUM RATINGS
Ta=25C
Parameter
Absolute Maximum Ratings
Input Voltage
Symbol
Rating
Units
Conditions
VIn,MAX
VOut,MAX
VCont,MAX
Tstg
-0.3 ~ 6.0
-0.3 ~ VIn+0.3
-0.3 ~ 6.0
V
V
Output pin Voltage
Control pin Voltage
V
Storage Temperature Range
-55 ~ 150
C
Internal Limited Tj=150°C *,
Power Dissipation
PD
400
mW
When mounted on PCB
Operating Condition
Operational Temperature Range
TOP
VOP
-40 ~ 85
1.8 ~ 6.0
C
Operational Voltage Range
V
* PD must be decreased at the rate of 3.2mW/C for operation above 25C.
The maximum ratings are the absolute limitation values with the possibility of the IC being damaged.
When operation exceeds this standard quality can not be guaranteed.
AP-MS0036-E-00
- 2 -
2011/02
[TK634xxAMF]
8-. ELECTRICAL CHARACTERISTICS
The parameters with min. or max. values will be guaranteed at Ta=Tj=25C with test when manufacturing or
SQC(Statistical Quality Control) methods. The operation between -40 ~ 85C is guaranteed by design.
VIn=VOut,TYP+1V, VCont=1.2V, Ta=Tj=25°C
Value
TYP
Parameter
Symbol
Units
Conditions
MIN
MAX
Output Voltage
VOut
LinReg
LoaReg
VDrop
IOut,MAX
IQ
V
IOut=5mA
Refer to TABLE 1
Line Regulation
-
0.0
4.0
mV
mV
mV
mA
µA
µA
µA
VIn=1V
Load Regulation
Refer to TABLE 1
Refer to TABLE 1
Refer to TABLE 1
Refer to TABLE 1
VOut=VOut,TYP0.9
IOut=0mA, VCont=VIn
VCont=0V
Dropout Voltage *1
Maximum Load Current *2
Quiescent Current
Standby Current
210
350
35
-
70
0.1
110
-
-
-
-
-
IStandby
IGND
0.01
55
GND Pin Current
IOut=50mA, VCont=VIn
VIn=5V, VOut=0.1V, VCont=0V
Discharge Resistance
Control Terminal
Control Current
RDis
25
ICont
-
1.2
-
0.7
1.4
-
µA
V
VCont=1.2V
-
-
VOut On state
VOut Off state
Control Voltage
VCont
0.2
V
Reference Value
Output Voltage / Temp.
Output Noise Voltage
(TK63428A)
-
-
100
35
-
-
ppm/°C IOut=5mA
VOut/Ta
COut=1.0µF, IOut=30mA,
µVrms
VNoise
BPF=400Hz~80kHz
Ripple Rejection
(TK63428A)
COut=1.0µF,
RR
tr
-
-
72
85
-
-
dB
IOut=10mA, f=1kHz
COut=1.0µF, IOut=30mA
VCont: Pulse Wave (100Hz),
VCont On VOut95% point
Rise Time
µs
(TK63428A)
*1: For VOut 1.8V, no regulations.
*2: The maximum output current is limited by power dissipation.
The maximum load current is the current where the output voltage decreases to 90% by increasing the output current at
Tj=25°C, compared to the output voltage specified at VIn=VOut,TYP+1V. The maximum load current indicates the current
at which over current protection turn on.
For all output voltage products, the maximum output current for normal operation without operating any protection is
200mA. Accordingly, LoaReg and VDrop are specified on the condition that IOut is less than 200mA.
General Note
Parameters with only typical values are just reference. (Not guaranteed)
The noise level is dependent on the output voltage, the capacitance and capacitor characteristics.
AP-MS0036-E-00
- 3 -
2011/02
[TK634xxAMF]
TABLE 1. Preferred Product (TK634xxAMF)
Load Regulation
Dropout Voltage
Output Voltage
Part Number
IOut=5 ~ 100mA IOut=5 ~ 200mA IOut=100mA
IOut=200mA
MIN TYP MAX TYP MAX TYP MAX TYP MAX TYP MAX
V
V
V
mV
10
10
10
10
10
10
10
10
10
11
11
11
11
11
mV
40
40
40
40
40
40
40
40
40
44
44
44
44
44
mV
19
20
20
20
20
20
20
20
20
21
21
21
21
21
mV
76
80
80
80
80
80
80
80
80
84
84
84
84
84
mV
-
mV
-
mV
-
mV
-
TK63415AMF
TK63418AMF
TK63425AMF
TK63426AMF
TK63427AMF
TK63428AMF
TK63401AMF
TK63429AMF
TK63430AMF
TK63431AMF
TK63432AMF
TK63433AMF
TK63435AMF
TK63440AMF
1.475 1.500 1.525
1.775 1.800 1.825
2.475 2.500 2.525
2.574 2.600 2.626
2.673 2.700 2.727
2.772 2.800 2.828
2.821 2.850 2.879
2.871 2.900 2.929
2.970 3.000 3.030
3.069 3.100 3.131
3.168 3.200 3.232
3.267 3.300 3.333
3.465 3.500 3.535
3.960 4.000 4.040
-
-
-
-
95
90
90
85
85
85
85
80
80
80
75
70
145
145
140
135
135
135
130
130
125
125
120
115
185
180
175
170
170
165
165
160
160
155
150
140
310
300
295
290
285
285
280
275
270
265
255
240
Notice.
Please contact your authorized Asahi Kasei Microdevices representative for voltage availability.
AP-MS0036-E-00
- 4 -
2011/02
[TK634xxAMF]
9-. TEST CIRCUIT
Test circuit for electrical characteristic
IIn
_
CIn
=1.0F
A
VIn
VOut
VCont GND
ICont
VCont
Notice.
COut
=1.0F
The limit value of electrical characteristics is applied when
CIn=1.0F(Ceramic), COut=1.0F(Ceramic).
But CIn, and COut can be used with both ceramic and
tantalum capacitors.
_
V
VIn=
VOut,TYP+1.0V
IOut
=5mA
VOut
_
A
VIn
VOut
VCont GND
ICont
VCont
VOut vs VIn
VDrop vs IOut
VOut vs IOut
VOut vs IOut
VOut vs Ta
VDrop vs Ta
CIn
=1.0F
COut
=1.0F
_
V
VIn
IOut
VOut
_
A
IOut,MAX vs Ta
ICont vs VCont , VOut vs VCont
ICont vs Ta
VCont vs Ta
VNoise vs VIn
VNoise vs IOut
VNoise vs VOut
VNoise vs Frequency
IIn
_
CIn
=1.0F
A
VIn
VOut
VCont GND
ICont
VCont
IQ vs VIn
IStandby vs VIn
IQ vs Ta
Open
COut
=1.0F
VIn=
VOut,TYP+1.0V
_
A
VIn
VOut
VCont GND
ICont IGND
VCont
IGND vs IOut
IGND vs Ta
CIn
=1.0F
COut
=1.0F
VIn=
IOut
_
A
_
A
VOut,TYP+1.0V
AP-MS0036-E-00
- 5 -
2011/02
[TK634xxAMF]
VIn=
VOut,TYP+1.5V
VIn
VOut
RR vs VIn
RR vs Frequency
RR vs Frequency
Vripple
500mVP-P
=
CIn
=1.0F
COut
=1.0F
VCont GND
IOut
=10mA
VCont
=1.2V
VOut,TYP+2V
VIn
VOut
Line Transient
Load Transient
On/Off Transient
COut
=1.0F
VOut,TYP+1V
VCont GND
_
V
IOut
=5mA
VOut
VOut
VOut
VCont
=1.2V
VIn
VOut
CIn
=1.0F
COut
=1.0F
VCont GND
_
V
VIn=
VOut,TYP+1.0V
IOut
VCont
=1.2V
VIn
VOut
CIn
=1.0F
COut
=1.0F
VCont GND
_
V
VIn=
VOut,TYP+1.0V
IOut=
VCont
=0V 1.2V
0mA or
30mA
AP-MS0036-E-00
- 6 -
2011/02
[TK634xxAMF]
10-. TYPICAL CHARACTERISTICS
10-1-. DC CHARACTERISTICS
VOut vs VIn (TK63415AMF)
VOut vs VIn (TK63415AMF)
10
40
IOut=0, 5, 50, 100, 150, 200mA
20
IOut=5mA
5
0
-5
0
-20
-10
-15
-20
-25
-30
-40
-60
-80
-100
0
1
2
3
4
4
4
5
6
6
6
-100
0
100
200
300
300
300
VIn [V]
VIn-VOut [mV]
VOut vs VIn (TK63428AMF)
VOut vs VIn (TK63428AMF)
10
5
40
IOut=0, 5, 50, 100, 150, 200mA
20
IOut=5mA
0
0
-20
-5
-10
-15
-20
-25
-30
-40
-60
-80
-100
0
1
2
3
5
-100
0
100
200
VIn [V]
VIn-VOut [mV]
VOut vs VIn (TK63442AMF)
VOut vs VIn (TK63442AMF)
10
5
40
IOut=0, 5, 50, 100, 150, 200mA
20
IOut=5mA
0
0
-20
-5
-10
-15
-20
-25
-30
-40
-60
-80
-100
0
1
2
3
5
-100
0
100
200
VIn [V]
VIn-VOut [mV]
AP-MS0036-E-00
- 7 -
2011/02
[TK634xxAMF]
VOut vs IOut (TK63415AMF)
2
1.5
1
0.5
0
0
100
200
300
300
300
400
400
400
500
500
500
IOut [mA]
VDrop vs IOut (TK63428AMF)
VOut vs IOut (TK63428AMF)
0
-50
4
3.5
3
-100
-150
-200
-250
-300
-350
-400
2.5
2
1.5
1
0.5
0
0
100
200
IOut [mA]
0
50
100
150
200
250
IOut [mA]
VDrop vs IOut (TK63442AMF)
VOut vs IOut (TK63442AMF)
0
-50
6
5
4
3
2
1
0
-100
-150
-200
-250
-300
-350
-400
0
100
200
IOut [mA]
0
50
100
150
200
250
IOut [mA]
AP-MS0036-E-00
- 8 -
2011/02
[TK634xxAMF]
VOut vs IOut (TK63415AMF)
VOut vs Ta (TK63415AMF)
10
5
100
80
0
60
-5
40
-10
-15
-20
-25
-30
-35
-40
20
0
-20
-40
-60
-80
-100
-50
-25
0
25
50
50
50
75
75
75
100
0
50
100
150
200
200
200
250
250
250
Ta [°C]
IOut [mA]
VOut vs IOut (TK63428AMF)
VOut vs Ta (TK63428AMF)
10
5
100
80
0
60
-5
40
-10
-15
-20
-25
-30
-35
-40
20
0
-20
-40
-60
-80
-100
-50
-25
0
25
100
0
50
100
150
Ta [°C]
IOut [mA]
VOut vs IOut (TK63442AMF)
VOut vs Ta (TK63442AMF)
10
5
100
80
0
60
-5
40
-10
-15
-20
-25
-30
-35
-40
20
0
-20
-40
-60
-80
-100
-50
-25
0
25
100
0
50
100
150
Ta [°C]
IOut [mA]
AP-MS0036-E-00
- 9 -
2011/02
[TK634xxAMF]
IOut,MAX vs Ta (TK63415AMF)
400
300
200
-50
-25
0
25
50
50
50
75
75
75
100
100
100
Ta [°C]
VDrop vs Ta (TK63428AMF)
IOut,MAX vs Ta (TK63428AMF)
0
-50
400
IOut=100mA
IOut=200mA
-100
-150
-200
-250
-300
-350
-400
300
200
-50
-25
0
25
-50
-25
0
25
50
75
100
Ta [°C]
Ta [°C]
VDrop vs Ta (TK63442AMF)
IOut,MAX vs Ta (TK63442AMF)
0
-50
400
IOut=100mA
IOut=200mA
-100
-150
-200
-250
-300
-350
-400
300
200
-50
-25
0
25
-50
-25
0
25
50
75
100
Ta [°C]
Ta [°C]
AP-MS0036-E-00
- 10 -
2011/02
[TK634xxAMF]
IQ vs VIn (TK63415AMF)
IStandby vs VIn (TK63415AMF)
100
90
80
70
60
50
40
30
20
10
0
10
9
8
7
6
5
4
3
2
1
0
VCont=VIn
VCont=0V
0
1
2
3
4
4
4
5
6
6
6
0
1
2
3
4
4
4
5
6
6
6
VIn [V]
VIn [V]
IQ vs VIn (TK63428AMF)
IStandby vs VIn (TK63428AMF)
100
90
80
70
60
50
40
30
20
10
0
10
9
8
7
6
5
4
3
2
1
0
VCont=VIn
VCont=0V
0
1
2
3
5
0
1
2
3
5
VIn [V]
VIn [V]
IQ vs VIn (TK63442AMF)
IStandby vs VIn (TK63442AMF)
100
90
80
70
60
50
40
30
20
10
0
10
9
8
7
6
5
4
3
2
1
0
VCont=VIn
VCont=0V
0
1
2
3
5
0
1
2
3
5
VIn [V]
VIn [V]
AP-MS0036-E-00
- 11 -
2011/02
[TK634xxAMF]
IGND vs IOut (TK63415AMF)
IQ vs Ta (TK63415AMF)
100
90
80
70
60
50
40
30
20
10
0
200
180
160
140
120
100
80
VCont=VIn
VCont=VIn
60
40
20
0
-50
-25
0
25
50
50
50
75
100
100
100
0
50
100
150
150
150
200
250
250
250
IOut [mA]
Ta [°C]
IGND vs IOut (TK63428AMF)
IQ vs Ta (TK63428AMF)
100
90
80
70
60
50
40
30
20
10
0
200
180
160
140
120
100
80
VCont=VIn
VCont=VIn
60
40
20
0
-50
-25
0
25
75
0
50
100
IOut [mA]
200
Ta [°C]
IGND vs IOut (TK63442AMF)
IQ vs Ta (TK63442AMF)
100
90
80
70
60
50
40
30
20
10
0
200
180
160
140
120
100
80
VCont=VIn
VCont=VIn
60
40
20
0
-50
-25
0
25
75
0
50
100
IOut [mA]
200
Ta [°C]
AP-MS0036-E-00
- 12 -
2011/02
[TK634xxAMF]
ICont vs VCont, VOut vs VCont (TK63415AMF)
IGND vs Ta (TK63415AMF)
100
90
80
70
60
50
40
30
20
10
0
2
1.5
1
2
VCont=VIn , IOut=50mA
VOut
1.5
1
0.5
0
0.5
0
ICont
-50
-25
0
25
50
75
100
100
100
0
0.5
1
1.5
2
2
2
VCont [V]
Ta [°C]
IGND vs Ta (TK63428AMF)
ICont vs VCont, VOut vs VCont (TK63428AMF)
100
90
80
70
60
50
40
30
20
10
0
2
4
3
2
1
0
VCont=VIn , IOut=50mA
VOut
1.5
1
0.5
ICont
0
-50
-25
0
25
50
75
0
0.5
1
1.5
VCont [V]
Ta [°C]
IGND vs Ta (TK63442AMF)
ICont vs VCont, VOut vs VCont (TK63442AMF)
100
90
80
70
60
50
40
30
20
10
0
2
8
6
4
2
0
VCont=VIn , IOut=50mA
VOut
1.5
1
0.5
ICont
0
-50
-25
0
25
50
75
0
0.5
1
1.5
VCont [V]
Ta [°C]
AP-MS0036-E-00
- 13 -
2011/02
[TK634xxAMF]
VCont vs Ta (TK63415AMF)
ICont vs Ta (TK634xxAMF)
1.4
1.2
1
1
VCont=1.2V
0.75
0.5
0.25
0
0.8
0.6
0.4
0.2
0
-50
-25
0
25
50
75
100
-50
-25
0
25
50
50
50
75
75
75
100
100
100
Ta [°C]
Ta [°C]
VCont vs Ta (TK63428AMF)
1.4
1.2
1
0.8
0.6
0.4
0.2
0
-50
-25
0
25
Ta [°C]
VCont vs Ta (TK63442AMF)
1.4
1.2
1
0.8
0.6
0.4
0.2
0
-50
-25
0
25
Ta [°C]
AP-MS0036-E-00
- 14 -
2011/02
[TK634xxAMF]
10-2-. AC CHARACTERISTICS
RR vs VIn (TK63415AMF)
RR vs Frequency (TK63415AMF)
0
0
Vripple=0.1Vp-p, f=1kHz
IOut=10mA
-10
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-20
COut=1.0F(tant.)
IOut= 200mA
150mA
100mA
50mA
-30
-40
-50
-60
-70
-80
-90
-100
10mA
COut=1.0 F(cer.)
0
0.5
1
1.5
2
2.5
3
3.5
100
1k
10k
100k
1M
Frequency [Hz]
VIn-VOut,TYP [V]
RR vs VIn (TK63428AMF)
RR vs Frequency (TK63428AMF)
0
0
Vripple=0.1Vp-p, f=1kHz
IOut=10mA
-10
-10
-20
-20
COut=1.0F(tant.)
IOut= 200mA
-30
-40
-50
-60
-30
-40
-50
-60
-70
-80
-90
-100
150mA
100mA
50mA
10mA
COut=1.0 F(cer.)
-70
-80
-90
-100
0
0.5
1
1.5
2
2.5
3
3.5
100
1k
10k
Frequency [Hz]
100k
1M
VIn-VOut,TYP [V]
RR vs VIn (TK63442AMF)
RR vs Frequency (TK63442AMF)
0
0
-10
-20
Vripple=0.1Vp-p, f=1kHz
IOut=10mA
-10
-20
COut=1.0F(tant.)
-30
-40
-50
-60
IOut= 200mA
150mA
100mA
50mA
-30
-40
-50
-60
-70
-80
-90
-100
10mA
COut=1.0 F(cer.)
-70
-80
-90
-100
100
1k
10k
Frequency [Hz]
100k
1M
0
0.5
1
1.5
2
2.5
VIn-VOut,TYP [V]
AP-MS0036-E-00
- 15 -
2011/02
[TK634xxAMF]
RR vs Frequency (TK63415AMF)
The ripple rejection (RR) characteristic depends on the
characteristic and the capacitance value of the capacitor
connected to the output side. The RR characteristic of
50kHz or more varies greatly with the capacitor on the
output side and PCB pattern. If necessary, please confirm
stability of your design.
0
-10
-20
-30
-40
-50
-60
IOut=10mA
COut=0.68F(cer.)
1.0F(cer.)
-70
-80
F(cer.)
-90
-100
100
1k
10k
100k
1M
Frequency [Hz]
RR vs Frequency (TK63428AMF)
0
-10
-20
-30
-40
-50
-60
IOut=10mA
COut=0.68F(cer.)
1.0F(cer.)
-70
-80
F(cer.)
-90
-100
100
1k
10k
100k
1M
Frequency [Hz]
RR vs Frequency (TK63442AMF)
0
-10
-20
-30
-40
-50
-60
IOut=10mA
COut=0.68F(cer.)
1.0F(cer.)
-70
-80
F(cer.)
-90
-100
100
1k
10k
100k
1M
Frequency [Hz]
AP-MS0036-E-00
- 16 -
2011/02
[TK634xxAMF]
VNoise vs VIn (TK63415AMF)
VNoise vs IOut (TK63415AMF)
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
IOut=30mA
1
2
3
4
5
6
0
0
50
100
150
200
200
200
250
250
250
VIn [V]
IOut [mA]
VNoise vs VIn (TK63428AMF)
VNoise vs IOut (TK63428AMF)
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
IOut=30mA
0
50
100
150
2.5
3
3.5
4
4.5
5
5.5
6
VIn [V]
IOut [mA]
VNoise vs VIn (TK63442AMF)
VNoise vs IOut (TK63442AMF)
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
IOut=30mA
4
4.5
5
5.5
6
0
50
100
150
VIn [V]
IOut [mA]
AP-MS0036-E-00
- 17 -
2011/02
[TK634xxAMF]
VNoise vs Frequency (TK63415AMF)
VNoise vs VOut (TK634xxAMF)
100
90
80
70
60
50
40
30
20
10
0
10
IOut=30mA
IOut=10mA
1
0.1
0.01
1.5
2
2.5
3
3.5
4
4.5
10
100
1k
10k
100k
100k
100k
VOut [V]
Frequency [Hz]
VNoise vs Frequency (TK63428AMF)
10
IOut=10mA
1
0.1
0.01
10
100
1k
10k
Frequency [Hz]
VNoise vs Frequency (TK63442AMF)
10
IOut=10mA
1
0.1
0.01
10
100
1k
10k
Frequency [Hz]
AP-MS0036-E-00
- 18 -
2011/02
[TK634xxAMF]
10-3-. TRANSIENT CHARACTERISTICS
Line Transient (TK63415AMF)
Load Transient (IOut=5100mA) (TK63415AMF)
VIn
1V/div
3.5V
IOut
100mA
100mA/div
100mV/div
2.5V
5mA
IOut=50, 100, 200mA
VOut
COut=0.68, 1.0, 2.2F
VOut
10mV/div
20sec/div
Time
20sec/div
Time
Line Transient (TK63428AMF)
Load Transient (IOut=5100mA) (TK63428AMF)
VIn
1V/div
4.8V
IOut
100mA
100mA/div
100mV/div
3.8V
5mA
IOut=50, 100, 200mA
VOut
COut=0.68, 1.0, 2.2F
VOut
10mV/div
20sec/div
Time
20sec/div
Time
Line Transient (TK63442AMF)
Load Transient (IOut=5100mA) (TK63442AMF)
VIn
1V/div
6.2V
IOut
100mA
100mA/div
100mV/div
5.2V
5mA
IOut=50, 100, 200mA
VOut
COut=0.68, 1.0, 2.2F
VOut
10mV/div
20sec/div
Time
20sec/div
Time
AP-MS0036-E-00
- 19 -
2011/02
[TK634xxAMF]
Load Transient (0100mA) (TK63428AMF/M5)
100mA
Load Transient (IOut=0 or 5100mA) (TK63415AMF)
100mA
IOut
IOut
100mA/div
100mV/div
0 or 5mA
100mA/div
0 or 5mA
0
100mA
0 100mA
VOut
VOut
100mV/div
5 100mA
5 100mA
10msec/div
Time
10sec/div
Time
Load Transient (IOut=0 or 5100mA) (TK63428AMF)
Load Transient 0100mA) (TK63428AMF/M5)
100mA
100mA
IOut
IOut
100mA/div
100mV/div
0 or 5mA
100mA/div
100mV/div
0 or 5mA
0 100mA
0 100mA
VOut
VOut
5
100mA
5 100mA
10msec/div
Time
10sec/div
Time
Load Transient (IOut=0 or 5100mA) (TK63442AMF)
Load Transient (0100mA) (TK63428AMF/M5)
100mA
100mA
IOut
IOut
100mA/div
100mV/div
0 or 5mA
100mA/div
100mV/div
0 or 5mA
0
100mA
0 100mA
VOut
VOut
5 100mA
5 100mA
10msec/div
Time
10sec/div
Time
AP-MS0036-E-00
- 20 -
2011/02
[TK634xxAMF]
On/Off Transient (VCont=1.20V) (TK63415AMF)
IOut=0mA
On/Off Transient (VCont=01.2V) (TK63415AMF)
VCont
IOut=30mA
VCont
1V/div
1V/div
COut=0.68, 1.0, 2.2F
VOut
500mV/div
200mA/div
VOut
COut=0.68, 1.0, 2.2F
0.5V/div
IIn
IIn
200mA/div
40sec/div
40µsec/div
Time
Time
On/Off Transient (VCont=01.2V) (TK63428AMF)
On/Off Transient (VCont=1.20V) (TK63428AMF)
IOut=0mA
VCont
IOut=30mA
VCont
1V/div
1V/div
COut=0.68, 1.0, 2.2F
VOut
1V/div
VOut
COut=0.68, 1.0, 2.2 F
1V/div
IIn
IIn
200mA/div
200mA/div
40sec/div
40µsec/div
Time
Time
On/Off Transient (VCont=01.2V) (TK63442AMF)
On/Off Transient (VCont=1.20V) (TK63442AMF)
IOut=0mA
VCont
IOut=30mA
VCont
1V/div
1V/div
COut=0.68, 1.0, 2.2F
VOut
2V/div
VOut
COut=0.68, 1.0, 2.2F
2V/div
IIn
IIn
200mA/div
200mA/div
40sec/div
40µsec/div
Time
Time
AP-MS0036-E-00
- 21 -
2011/02
[TK634xxAMF]
11-. PIN DESCRIPTION
Pin No.
Pin Description
Internal Equivalent Circuit
Description
Output Terminal
VIn
VOut
1
VOut
ESD
protection
On/Off
Control
GND Terminal
2
3
4
GND
VCont
VIn
Control Terminal
ESD
VCont > 1.2V : On
VCont < 0.2V : Off
protection
VCont
The pull-down resistor (about 1.65M) is built-in.
1.65M
Input Terminal
AP-MS0036-E-00
- 22 -
2011/02
[TK634xxAMF]
12-. APPLICATIONS INFORMATION
12-1-. Stability
Fig.12-2 shows the stable operation area of output
current and the equivalent series resistance (ESR) with a
ceramic capacitor of 0.68µF. ESR of the output capacitor
must be in the stable operation area. Please select the best
output capacitor according to the voltage and current
used. The stability of the regulator improves as the value
of the output side capacitor increases (the stable
operation area extends.) Please use as large a value
capacitor as is practical.
Linear regulators require input and output capacitors in
order to maintain the regulator's loop stability. If 0.68µF
capacitors are connected to the input side and the output
side, the IC provides stable operation. However, it is
recommended to use as large a value capacitor as is
practical. The output noise and the ripple noise decrease
as the value of the capacitor increases.
A recommended value of the application is as follows.
CIn0.68µF, COut0.68µF
It is not possible to determine this indiscriminately.
Please confirm the stability in your design.
For evaluation
Kyocera : CM05X5R105K10AB
Fig12-1: Capacitor in the application
Fig12-3: ex. Ceramic Capacitance vs Voltage,
Temperature
VIn
VOut
TK634xxA
Capacitance vs Voltage
CIn0.68µF
COut0.68µF
100
90
B Curve
VCont
80
70
60
50
F Curve
4
0
2
6
8
10
12
Bias Voltage(V)
Capacitance vs Temperature
100
90
80
70
60
50
B Curve
Fig12-2: Output Current vs Stable Operation Area
F Curve
-40~+85ºC
100
-50 -25
0
25
50
75
100
Ta(°C)
10
Generally, a ceramic capacitor has both a temperature
characteristic and a voltage characteristic. Please consider
both characteristics when selecting the part. The B curves
are the recommended characteristics.
Stable Area
1
0.1
0.01
0
50
100
150
200
IOut [mA]
AP-MS0036-E-00
- 23 -
2011/02
[TK634xxAMF]
Fig12-5: Derating Curve
12-2-. Layout
PD(mW)
900
-7.2mW/°C
PCB size
図12-4: Layout example
VIn
VCont
(30mm×30mm×1mm)
-3.2mW/°C
PCB size
(7mm×8mm×0.8mm)
400
VOut
GND
(Top View)
PCB Material: Glass epoxy
Size: 30mm×30mm×1mm
25
50
100
(85°C)
150°C
VIn
VCont
The package loss is limited at the temperature that the
internal temperature sensor works (about 150C).
Therefore, the package loss is assumed to be an internal
limitation. There is no heat radiation characteristic of the
package unit assumed because of its small size. Heat is
carried away from the device by being mounted on the
PCB. This value is directly effected by the material and
the copper pattern etc. of the PCB. The losses are
approximately 400mW. Enduring these losses becomes
possible in a lot of applications operating at 25C.
VOut
GND
(Top View)
PCB Material: Glass epoxy
Size: 7mm×8mm×0.8mm
The overheating protection circuit operates when the
junction temperature reaches 150C (this happens when
the regulator is dissipating excessive power, outside
temperature is high, or heat radiation is bad). The output
current and the output voltage will drop when the
protection circuit operates. However, operation begins
again as soon as the output voltage drops and the
temperature of the chip decreases.
Please do derating with 3.2mW/C(PCB size: 7mm×
8mm×0.8mm), 7.2mW/C(PCB size: 30mm×30mm×
1mm), at PD=400mW(PCB size: 7mm×8mm×0.8m),
900mW(PCB size: 30mm×30mm×1mm), and 25C or
more.
How to determine the thermal resistance when
mounted on PCB
The thermal resistance when mounted is expressed as
follows:
Tj=jaPD+Ta
Tj of IC is set around 150C. PD is the value when the
thermal sensor is activated.
If the ambient temperature is 25C, then:
150=jaPD+25
ja=125/PD (C /mW)
AP-MS0036-E-00
- 24 -
2011/02
[TK634xxAMF]
PD is easily calculated.
12-3-. On/Off Control
A simple way to determine PD is to calculate VInIIn
when the output side is shorted. Input current gradually
falls as output voltage rises after working thermal
shutdown. You should use the value when thermal
equilibrium is reached.
It is recommended to turn the regulator Off when the
circuit following the regulator is not operating. A design
with little electric power loss can be implemented. We
recommend the use of the On/Off control of the regulator
without using a high side switch to provide an output
from the regulator. A highly accurate output voltage with
low voltage drop is obtained.
Fig12-6: How to determine DPD
PD (mW)
Because the control current is small, it is possible to
control it directly by CMOS logic.
2
PD
Fig12-7: The use of On/Off control
Vsat
DPD
3
5
REG
4
On/Off Cont.
25
50
75
100 125 150
Ta (°C)
Procedure (When mounted on PCB.)
1. Find PD (VInIIn when the output side is short-
circuited).
Control Terminal Voltage ((VCont
)
On/Off State
VCont > 1.2V
VCont < 0.2V
On
Off
2. Plot PD against 25C.
3. Connect PD to the point corresponding to the 150C
Parallel Connected On/Off Control
with a straight line.
4. In design, take a vertical line from the maximum
operating temperature (e.g., 75C) to the derating
curve.
5. Read off the value of PD against the point at which the
vertical line intersects the derating curve. This is taken
as the maximum power dissipation DPd.
6. DPD (VIn,MAXVOut)=IOut (at 75C)
Fig12-8: The example of parallel connected IC
TK63442A
VIn
VOut
4.2V
2.8V
1.5V
TK63428A
TK63415A
The maximum output current at the highest operating
temperature will be IOut DPD (VIn,MAX-VOut).
Please use the device at low temperature with better
radiation. The lower temperature provides better quality.
On/Off
Cont.
The above figure is multiple regulators being controlled
by a single On/Off control signal. There is concern of
overheating, because the power loss of the low voltage
side IC (TK63415A) is large. The series resistor (R) is
put in the input line of the low output voltage regulator in
order to prevent over-dissipation. The voltage dropped
across the resistor reduces the large input-to-output
voltage across the regulator, reducing the power
dissipation in the device. When the thermal sensor works,
a decrease of the output voltage, oscillation, etc. may be
observed.
AP-MS0036-E-00
- 25 -
2011/02
[TK634xxAMF]
12-4-. Definition of term
Characteristics
Protections
Over Current Sensor
The over current sensor protects the device when there is
excessive output current. It also protects the device if the
output is accidentally connected to ground.
Output Voltage (VOut
)
The output voltage is specified with VIn=(VOutTYP+1V)
and IOut=5mA.
Maximum Output Current (IOut, MAX
)
Thermal Sensor
The rated output current is specified under the condition
where the output voltage drops to 90% of the value
specified with IOut=5mA. The input voltage is set to
VOutTYP+1V and the current is pulsed to minimize
temperature effect.
The thermal sensor protects the device in case the
junction temperature exceeds the safe value (Tj=150C).
This temperature rise can be caused by external heat,
excessive power dissipation caused by large input to
output voltage drops, or excessive output current. The
regulator will shut off when the temperature exceeds the
safe value. As the junction temperatures decrease, the
regulator will begin to operate again. Under sustained
fault conditions, the regulator output will oscillate as the
device turns off then resets. Damage may occur to the
device under extreme fault.
Dropout Voltage (VDrop
)
The dropout voltage is the difference between the input
voltage and the output voltage at which point the
regulator starts to fall out of regulation. Below this value,
the output voltage will fall as the input voltage is reduced.
It is dependent upon the output voltage, the load current,
and the junction temperature.
Please prevent the loss of the regulator when this
protection operates, by reducing the input voltage or
providing better heat efficiency.
Line Regulation (LinReg)
Line regulation is the ability of the regulator to maintain a
constant output voltage as the input voltage changes. The
line regulation is specified as the input voltage is changed
ESD
MM : 200pF 0 150V or more
HBM : 100pF 1.5k 2000V or more
from VIn=VOut,TYP+1V to VIn=6V. It is
measurement to minimize temperature effect.
a pulse
Load Regulation (LoaReg)
Load regulation is the ability of the regulator to maintain
a constant output voltage as the load current changes. It is
a pulsed measurement to minimize temperature effects
with the input voltage set to VIn=VOut,TYP+1V. The load
regulation is specified under an output current step
condition of 1mA to 50mA.
Ripple Rejection (RR)
Ripple rejection is the ability of the regulator to attenuate
the ripple content of the input voltage at the output. It is
specified with 500mVP-P, 1kHz super-imposed on the
input voltage, where VIn=VOut,TYP+1.5V. Ripple rejection
is the ratio of the ripple content of the output vs. input and
is expressed in dB.
Standby Current (IStandby
)
Standby current is the current which flows into the
regulator when the output is turned off by the control
function (VCont=0V).
AP-MS0036-E-00
- 26 -
2011/02
[TK634xxAMF]
13-. PACKAGE OUTLINE
4-Lead-Small Outline Non-Leaded Package with Heat Sink
: HSON1214-4
0.25
4
3
1 Pin Mark
1
2
0.5
+
0.05
1.2
1.00
Reference Mount Pad
+0.05
+
0.2
0.13
0.03
(0.075)
1
2
4
3
0.5
0.9+0.05
Unit : mm
Package Structure and Others
Package Material
Terminal Material : Copper Alloy
Terminal Finish : Ni/Pd/Au
: Epoxy Resin
Caution in Printed Circuit Board Layout
In addition to the normal pins, this plastic package has exposed metal tabs.
This tab is electrically connected to the GND of internal chip.
Avoid electrical contact with this tab from external print traces, adjacent components other than GND, etc.
This tab is recommended to be solder-mounted so as to enhance heat release.
AP-MS0036-E-00
- 27 -
2011/02
[TK634xxAMF]
Marking
Part Number
Marking Code
Part Number
Marking Code
Part Number
Marking Code
TK63415AMF
TK63418AMF
TK63425AMF
TK63426AMF
TK63427AMF
TK63428AMF
D15
TK63401AMF
D01
TK63435AMF
D35
D18
D25
D26
D27
D28
TK63429AMF
TK63430AMF
TK63431AMF
TK63432AMF
TK63433AMF
D29
D30
D31
D32
D33
TK63440AMF
D40
AP-MS0036-E-00
- 28 -
2011/02
[TK634xxAMF]
IMPORTANT NOTICE
These products and their specifications are subject to change without notice.
When you consider any use or application of these products, please make inquiries the sales office of
Asahi Kasei Microdevices Corporation (AKM) or authorized distributors as to current status of the
products.
Descriptions of external circuits, application circuits, software and other related information contained
in this document are provided only to illustrate the operation and application examples of the
semiconductor products. You are fully responsible for the incorporation of these external circuits,
application circuits, software and other related information in the design of your equipments. AKM
assumes no responsibility for any losses incurred by you or third parties arising from the use of these
information herein. AKM assumes no liability for infringement of any patent, intellectual property, or
other rights in the application or use of such information contained herein.
Any export of these products, or devices or systems containing them, may require an export license or
other official approval under the law and regulations of the country of export pertaining to customs
and tariffs, currency exchange, or strategic materials.
AKM products are neither intended nor authorized for use as critical componentsNote1) in any safety,
life support, or other hazard related device or systemNote2), and AKM assumes no responsibility for
such use, except for the use approved with the express written consent by Representative Director of
AKM. As used here:
Note1) A critical component is one whose failure to function or perform may reasonably be expected to
result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system
containing it, and which must therefore meet very high standards of performance and reliability.
Note2) A hazard related device or system is one designed or intended for life support or maintenance of
safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to
function or perform may reasonably be expected to result in loss of life or in significant injury or damage to
person or property.
It is the responsibility of the buyer or distributor of AKM products, who distributes, disposes of, or
otherwise places the product with a third party, to notify such third party in advance of the above
content and conditions, and the buyer or distributor agrees to assume any and all responsibility and
liability for and hold AKM harmless from any and all claims arising from the use of said product in
the absence of such notification.
AP-MS0036-E-00
- 29 -
2011/02
相关型号:
TK63431AMFG0L-C
Fixed Positive LDO Regulator, 3.1V, 0.275V Dropout, CMOS, PDSO4, 1.20 X 1.40 MM, LEAD FREE, PLASTIC, SON-4
AKM
TK63431AMFG0L-C
Fixed Positive LDO Regulator, 3.1V, 0.275V Dropout, CMOS, PDSO4, 1.20 X 1.40 MM, LEAD FREE, PLASTIC, SON-4
TOKO
©2020 ICPDF网 联系我们和版权申明