A3961SB [ALLEGRO]
DUAL FULL-BRIDGE PWM MOTOR DRIVER; 双路全桥式PWM电动机驱动器型号: | A3961SB |
厂家: | ALLEGRO MICROSYSTEMS |
描述: | DUAL FULL-BRIDGE PWM MOTOR DRIVER |
文件: | 总10页 (文件大小:92K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
3961
DUAL FULL-BRIDGE PWM MOTOR DRIVER
Designed for pulse-width modulated (PWM) current control of
bipolar stepper motors, the A3961S— is capable of continuous output
24
23
OUT
2B
1
OUT
currents to ±800 mA and operating voltages to 45 V. Internal fixed
off-time PWM current-control circuitry can be used to regulate the
maximum load current to a desired value. An internal precision voltage
reference is provided to improve motor peak current control accuracy.
The peak load current limit is set by the user’s selection of an external
resistor divider and current-sensing resistors.
1B
E 2
2
3
4
5
E1
22 SENSE2
SENSE1
OUT1A
VBB1
21
OUT
2A
20
VBB2
GROUND
6
7
19
18
17
16
15
14
13
GROUND
GROUND
GROUND
I FULL/PD
The fixed off-time pulse duration is set by user-selected external
RC timing networks. The capacitor in the RC timing network also
determines a user-selectable blanking window that prevents false
triggering of the PWM current control circuitry during switching transi-
tions. This eliminates the need for two external RC filter networks on
the current-sensing comparator inputs.
8
9
V
REFOUT
V
REFIN
VCC
10
11
RC1
RC2
PHASE1
PHASE2
ENABLE2
12
ENABLE1
For each bridge the PHASE input controls load current polarity by
selecting the appropriate source and sink driver pair. For each bridge
the ENABLE input, when held high, disables the output drivers. Special
power-up sequencing is not required. Internal circuit protection includes
thermal shutdown with hysteresis, transient-suppression diodes, and
crossover-current protection.
Note the A3961SB (DIP) and the A3961SLB
(SOIC) are electrically identical and share a
common terminal number assignment.
ABSOLUTE MAXIMUM RATINGS
Load Supply Voltage, VBB . . . . . . . . . . 45 V
Output Current, IOUT . . . . . . . . . . ±800 mA*
Logic Supply Voltage, VCC . . . . . . . . . 7.0 V
The A3961S— is supplied in a choice of two power packages:
24-pin dual-in-line plastic package with copper heat-sink tabs and
24-lead plastic SOIC with copper heat-sink tabs. In both packages the
power tab is at ground potential and needs no electrical isolation.
Logic Input Voltage Range,
VIN . . . . . . . . . . . -0.3 V to VCC + 0.3 V
Sense Voltage, VSENSE . . . . . . . . . . . . 1.0 V
FEATURES
Reference Output Current,
IREF OUT . . . . . . . . . . . . . . . . . . . 1.0 mA
■ ±800 mA Continuous Output Current Rating
■ 45 V Output Voltage Rating
■ Internal PWM Current Control, Saturated Sink Drivers
■ Internally Generated Precision 2.5 V Reference
■ Internal Transient-Suppression Diodes
■ Internal Thermal-Shutdown Circuitry
Package Power Dissipation,
PD . . . . . . . . . . . . . . . . . . . . See Graph
Operating Temperature Range,
TA . . . . . . . . . . . . . . . . . -20˚C to +85˚C
Junction Temperature, TJ . . . . . . . +150˚C†
Storage Temperature Range,
■ Crossover-Current Protection, UVLO Protection
TS . . . . . . . . . . . . . . . . -55˚C to +150˚C
* Output current rating may be limited by duty
cycle, ambient temperature, and heat sinking.
Under any set of conditions, do not exceed the
specified current rating or a junction tempera-
ture of 150˚C.
Always order by complete part number:
PART NUMBER
PACKAGE
RθJA
RθJT
† Fault conditions that produce excessive
junction temperature will activate device
thermal shutdown circuitry. These conditions
can be tolerated but should be avoided.
A3961SB
24-Pin DIP
40°C/W
6°C/W
A3961SLB
24-Lead SOIC
55°C/W
6°C/W
3961
DUAL FULL-BRIDGE
PWM MOTOR DRIVER
5
R
= 6.0°C/W
TRUTH TABLE
θJT
4
3
ENABLE
PHASE
OUTA
Off
H
OUTB
Off
L
H
L
L
X
H
L
SUFFIX 'B', R
= 40°C/W
θJA
2
1
0
L
H
X = Irrelevant
SUFFIX 'LB', R
= 55°C/W
θJA
25
50
75
100
125
150
Dwg. GP-049A
TEMPERATURE IN °C
FUNCTIONAL BLOCK DIAGRAM AND TYPICAL
BIPOLAR STEPPER MOTOR APPLICATION
MOTOR SUPPLY 2
LOGIC SUPPLY
MOTOR SUPPLY 1
CBB
C BB2
GND
Ccc
VBB2
VBB1
Vcc
OUT
OUT
2A
2B
OUT
OUT
1A
1B
ENABLE 2
PHASE 2
ENABLE 1
PHASE 1
CONTROL LOGIC
AND LEVEL SHIFT
CONTROL LOGIC
AND LEVEL SHIFT
UVLO
AND
TSD
VOLTAGE
REFERENCE
BLANKING
TIME AND
SOURCE
DRIVER TOFF
CONTROL
BLANKING
TIME AND
SOURCE
DRIVER TOFF
CONTROL
RC
1
+
_
+
RC
2
_
I
REF
OUT
E
SENSE
2
SENSE
REF
E
FULL/PD
1
1
2
IN
R
1
C
C
R
R
T2
T2
T1
T1
R
R
S1
R
2
S2
E
2
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
Copyright ©1995, 1996, Allegro MicroSystems, Inc.
3961
DUAL FULL-BRIDGE
PWM MOTOR DRIVER
ELECTRICAL CHARACTERISTICS at TA = +25°C, VBB = 45 V, VCC = 4.75 V to 5.25 V, VSENSE = 0
V, 30 kΩ & 1000 pF RC to Ground (unless noted otherwise)
Limits
Characteristic
Symbol
Test Conditions
Min.
Typ.
Max.
Units
Output Drivers
Load Supply Voltage Range
Output Leakage Current
VBB
ICEX
Operating, IOUT = ±800 mA, L = 3 mH
VOUT = VBB
5.0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
<1.0
<-1.0
1.0
1.1
—
45
50
V
µA
µA
V
VOUT = 0 V
-50
1.2
1.3
1.4
0.6
0.9
1.0
1.4
1.6
1.7
7.0
7.0
Output Saturation Voltage
VCE(SAT)
Source Driver, IOUT = -500 mA
Source Driver, IOUT = -750 mA
Source Driver, IOUT = -800 mA
Sink Driver, IOUT = +500 mA
Sink Driver, IOUT = +750 mA
Sink Driver, IOUT = +800 mA
IF = 500 mA
V
V
0.3
0.5
—
V
V
V
Clamp Diode Forward Voltage
(Sink or Source)
VF
1.1
1.3
—
V
IF = 750 mA
V
IF = 800 mA
V
Motor Supply Current
(No Load)
IBB(ON)
VENABLE = 0.8 V
5.0
5.0
mA
mA
IBB(OFF)
VENABLE = 2.4 V
Control Logic
Logic Supply Voltage Range
Logic Input Voltage
VCC
VIN(1)
VIN(0)
IIN(1)
Operating
4.75
2.4
—
—
—
5.25
—
V
V
—
0.8
20
V
Logic Input Current
VIN = 2.4 V
VIN = 0.8 V
—
<1.0
<-2.0
µA
µA
IIN(0)
—
-200
Reference Output Voltage
VREF OUT
VCC = 5.0 V, IREF OUT = 90 to 900 µA:
IFULL/PD = LOW
2.45
1.49
2.50
1.67
2.55
1.84
V
V
IFULL/PD = HIGH
Continued next page…
3961
DUAL FULL-BRIDGE
PWM MOTOR DRIVER
ELECTRICAL CHARACTERISTICS at TA = +25°C, VBB = 45 V, VCC = 4.75 V to 5.25 V, VSENSE = 0
V, 30 kW & 1000 pF RC to Ground (unless noted otherwise) (cont.)
Limits
Characteristic
Symbol
Test Conditions
Min.
Typ.
Max.
Units
Control Logic (Continued)
Reference Output Current
Ref. Input Offset Current
Comparator Input Offset Volt.
Comparator Input Volt. Range
PWM RC Fixed Off-time
IREF OUT
IOS
3 kΩ ≤ RD = R1 + R2 ≤ 15 kΩ
VREF IN = 1 V
90
-2.5
-5.0
-0.3
27
—
0
900
1.0
5.0
1.0
33
µA
µA
mV
V
VIO
VREF = 0 V
0
VREF
tOFF RC
tPWM
tON(min)
tpd
Operating
—
30
1.2
2.5
CT = 1000 pF, RT = 30 kΩ
Comparator Trip to Source OFF
CT = 1000 pF ± 5%, RT ≥ 15 kΩ, VCC = 5 V
µs
µs
µs
PWM Propagation Delay Time
PWM Minimum On Time
Propagation Delay Times
—
2.0
3.6
—
IOUT = ±800 mA, 50% to 90%:
ENABLE ON to Source ON
ENABLE OFF to Source OFF
ENABLE ON to Sink ON
—
—
—
—
—
—
—
—
3.2
1.2
3.2
0.7
3.2
3.2
0.7
1.2
—
—
—
—
—
—
—
—
µs
µs
µs
µs
µs
µs
µs
µs
ENABLE OFF to Sink OFF
PHASE Change to Sink ON
PHASE Change to Source ON
PHASE Change to Sink OFF
PHASE Change to Source OFF
Thermal Shutdown Temp.
Thermal Shutdown Hysteresis
UVLO Disable Threshold
UVLO Hysterisis
TJ
—
—
165
15
—
—
˚C
˚C
V
∆TJ
2.5
0.7
—
2.7
0.9
65
2.9
1.1
85
15
—
V
Logic Supply Current
ICC(ON)
ICC(OFF)
∆ICC(ON)
VENABLE1 = VENABLE2 = 0.8 V
VENABLE1 = VENABLE2 = 2.4 V
VENABLE1 = VENABLE2 = 0.8 V
mA
—
11
Logic Supply Current
—
0.18
mA/˚C
Temperature Coefficient
NOTES: 1. Typical Data is for design information only.
2. Negative current is defined as coming out of
(sourcing) the specified device terminal.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
3961
DUAL FULL-BRIDGE
PWM MOTOR DRIVER
FUNCTIONAL DESCRIPTION
internal current-control circuitry (or by the PHASE or
ENABLE inputs). The comparator output is blanked to
prevent false over-current detections due to reverse-
recovery currents of the clamp diodes, and/or switching
transients related to distributed capacitance in the load.
Internal PWM Current Control. The A3961S— contains
a fixed off-time pulse-width modulated (PWM) current-
control circuit that can be used to limit the load current to
a desired value. The peak value of the current limiting
(ITRIP) is set by the selection of an external current-sensing
resistor (RS) and reference input voltage (VREF IN).
The internal circuitry compares the voltage across the
external sense resistor to the voltage on the reference
input terminal (VREF IN), resulting in a transconductance
function approximated by:
During internal PWM operation, at the end of the tOFF
time, the comparator’s output is blanked and CT begins to
be charged from approximately 1.1 volts by an internal
current source of approximately 1 mA. The comparator
output remains blanked until the voltage on CT reaches
approximately 3.0 volts.
VREF IN
When a transition of the PHASE input occurs, CT
is discharged to near ground during the crossover delay
time (The crossover delay time is present to prevent
simultaneous conduction of the source and sink drivers).
After the crossover delay, CT is charged by an internal cur-
rent source of approximately 1 mA. The comparator out-
put remains blanked until the voltage on CT reaches
approximately 3.0 volts.
ITRIP
≈
RS
The reference input voltage is typically set with a
resistor divider from VREF OUT. The value of VREF OUT
can be switched from a nominal value of 2.5 V to 1.67 V
by applying a low or high logic signal respectively to the
I FULL/PD terminal. To ensure proper operation of the
voltage reference, the resistor divider (RD = R1+R2) should
have an impedance of 3 kΩ to 15 kΩ. Within this range, a
low impedance will minimize the effect of the REF IN input
offset current.
When the device is disabled, via the ENABLE input,
CT is discharged to near ground. When the device is
re-enabled, CT is charged by an internal current source
of approximately 1 mA. The comparator output remains
blanked until the voltage on CT reaches approximately
3.0 volts.
The current-control circuitry limits the load current as
follows: when the load current reaches ITRIP, the compara-
tor resets a latch that turns off the selected source driver.
The load inductance causes the current to recirculate
through the sink driver and flyback diode.
The minimum recommended value for CT is
1000 pF. This value ensures that the blanking time is suffi-
cient to avoid false trips of the comparator under normal
operating conditions. For optimal regulation of the load
current, the above value for CT is recommended and the
value of RT can be sized to determine tOFF. For more infor-
mation regarding load current regulation, see below.
For each bridge, the user selects an external resistor
(RT) and capacitor (CT) to determine the time period
(tOFF = RTCT) during which the source driver remains dis-
abled (see “RC Fixed Off-time” below). The range of rec-
ommended values for CT and RT are 1000 pF to
1500 pF and 15 kΩ to 100 kΩ respectively. For optimal
load current regulation, CT is normally set to 1000 pF (see
“Load Current Regulation” below). At the end of the RC in-
terval, the source driver is enabled allowing the load cur-
rent to increase again. The PWM cycle repeats, maintain-
ing the peak load current at the desired value.
Load Current Regulation. Because the device operates
in a slow decay mode (2-quadrant PWM mode), there is a
limit to the lowest level that the PWM current control cir-
cuitry can regulate load current. The limitation is due to the
minimum PWM duty cycle, which is a function of the user-
selected value of tOFF and the minimum on-time pulse
tON(min)max that occurs each time the PWM latch is reset.
If the motor is not rotating, as in the case of a stepper mo-
tor in hold/detent mode, a brush dc motor when stalled or
at startup, the worst case value of current regulation can
be approximated by:
RC BLANKING. In addition to determining the fixed off-
time of the PWM control circuit, the CT component sets the
comparator blanking time. This function blanks the output
of the comparator when the outputs are switched by the
[(VBB - VSAT(SOURCE+SINK)) tON(min)max] – (1.05 (VSAT(SINK) + VF) tOFF
)
I AVG
≈
1.05 (tON(min)max + tOFF) RLOAD
3961
DUAL FULL-BRIDGE
PWM MOTOR DRIVER
where tOFF = RTCT, RLOAD is the series resistance of the
load, VBB is the motor supply voltage and t ON(min)max is
specified in the electrical characteristics table. When the
motor is rotating, the back EMF generated will influence
the above relationship. For brush dc motor applications,
the current regulation is improved. For stepper motor
applications when the motor is rotating, the effect is
dependent on the polarity and magnitude of the motor’s
back EMF.
tween the duty cycle on the PHASE input and the average
voltage applied to the motor is more linear than in the case
of ENABLE PWM control (which produces a discontinuous
current at low current levels).
Miscellaneous Information. An internally generated dead
time prevents crossover currents that can occur when
switching phase.
Thermal protection circuitry turns OFF all drivers
should the junction temperature reach 165°C (typical).
This is intended only to protect the device from failures
due to excessive junction temperatures and should not
imply that output short circuits are permitted. The hyster-
esis of the thermal shutdown circuit is approximately 15°C.
The following procedure can be used to evaluate the
worst-case internal PWM load current regulation in the
system:
Set VREF to 0 volts. With the load connected and
the PWM current control operating in slow decay mode,
use an oscilloscope to measure the time the output is
low (sink ON) for the output that is chopping. This is the
typical minimum on time (tON(min)typ) for the device. The
CT then should be increased until the measured value of
tON(min) is equal to tON(min)max as specified in the electrical
characteristics table. When the new value of CT has been
set, the value of RT should be decreased so the value for
tOFF = RTCT (with the artificially increased value of CT)
is equal to the nominal design value. The worst-case load-
current regulation then can be measured in the system
under operating conditions.
APPLICATION NOTES
Current Sensing. The actual peak load current (IPEAK
)
will be above the calculated value of ITRIP due to delays in
the turn off of the drivers. The amount of overshoot can be
approximated by:
(VBB – [(ITRIP RLOAD) + VBEMF]) tPWM
IOS
≈
LLOAD
where VBB is the motor supply voltage, VBEMF is the
back-EMF voltage of the load, RLOAD and LLOAD are the
resistance and inductance of the load respectively, and
t PWM is specified in the electrical characteristics table.
PWM of the Phase and Enable Inputs. The PHASE and
ENABLE inputs can be pulse width modulated to regulate
load current. Typical propagation delays from the PHASE
and ENABLE inputs to transitions of the power outputs are
specified in the electrical characteristics table. If the inter-
nal PWM current control is used, the comparator blanking
function is active during phase and enable transitions. This
eliminates false tripping of the over-current comparator
caused by switching transients (see “RC Blanking” above).
To minimize current sensing inaccuracies caused by
ground trace IR drops, each current-sensing resistor
should have a separate return to the ground terminal of the
device. For low-value sense resistors, the IR drops in the
PCB can be significant and should be taken into account.
The use of sockets should be avoided as their contact
resistance can cause variations in the effective value of
RS.
Enable PWM. Toggling the ENABLE input turns ON and
OFF the selected source and sink drivers. The corre-
sponding pair of flyback and ground clamp diodes conduct
after the drivers are disabled, resulting in fast current de-
cay. When the device is enabled the internal current-con-
trol circuitry will be active and can be used to limit the load
current in a slow decay mode.
Generally, larger values of RS reduce the aforemen-
tioned effects but can result in excessive heating and
power loss in the sense resistor. The selected value of RS
should not cause the absolute maximum voltage rating of
1.0 V, for the SENSE terminal, to be exceeded. The
recommended value of RS is in the range of:
Phase PWM. Toggling the PHASE terminal selects which
sink/source pair is enabled, producing a load current that
varies with the duty cycle and remains continuous at all
times. This can have added benefits in bidirectional brush
dc servo motor applications as the transfer function be-
0.5
± 50%
RS ≈
ITRIPmax
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
3961
DUAL FULL-BRIDGE
PWM MOTOR DRIVER
If desired, the reference input voltage can be filtered
by placing a capacitor from REFIN to ground. The ground
return for this capacitor as well as R2 should be indepen-
dent from the high-current power-ground trace to avoid
changes in REFIN due to IR drops.
Thermal Considerations. For reliable operation it is
recommended that the maximum junction temperature be
kept below 110 to 125°C. The junction temperature can
be measured best by attaching a thermocouple to the
power tab/batwing of the device and measuring the tab
temperature, TTAB . The junction temperature can then be
approximated by using the formula:
TJ ≈ TTAB + (ILOAD 2 VF RθJT
)
where VF can be chosen from the electrical specification
table for the given level of ILOAD. The value for RθJT is
given in the package thermal resistance table for the
appropriate package.
The power dissipation of the batwing packages can
be improved by 20 to 30% by adding a section of printed
circuit board copper (typically 6 to 18 square centimeters)
connected to the batwing terminals of the device.
The thermal performance in applications that run at
high load currents and/or high duty cycles can be im-
proved by adding external diodes from each output to
ground in parallel with the internal diodes. Fast recovery
(≤ 200 ns) diodes should be used to minimize switching
losses.
The load supply terminal, VBB, should be decoupled
with an electrolytic capacitor (≥ 47 µF is recommended)
placed as close to the device as is physically practical.
To minimize the effect of system ground IR drops on the
logic and reference input signals the system ground should
have a low-resistance return to the motor supply voltage.
See also “Current Sensing” and “Thermal Consider-
ations” above.
Fixed Off-Time Selection. With increasing values of tOFF
switching losses will decrease, low-level load current
regulation will improve, EMI will be reduced, the PWM
frequency will decrease, and ripple current will increase.
The value of tOFF can be chosen for optimization of these
parameters. For applications where audible noise is a
concern, typical values of tOFF are chosen to be in the
range of 15 to 35 µs.
,
3961
DUAL FULL-BRIDGE
PWM MOTOR DRIVER
A3961SB
Dimensions in Inches
(controlling dimensions)
0.014
0.008
NOTE 1
24
13
0.430
MAX
0.280
0.240
0.300
BSC
1
6
7
12
0.100
0.070
0.045
0.005
BSC
MIN
1.280
1.230
0.210
MAX
0.015
0.150
0.115
MIN
0.022
0.014
Dwg. MA-001-25A in
Dimensions in Millimeters
(for reference only)
0.355
0.204
NOTE 1
24
13
10.92
MAX
7.11
6.10
7.62
BSC
1
6
7
12
2.54
1.77
1.15
0.13
BSC
MIN
32.51
31.24
5.33
MAX
0.39
3.81
2.93
MIN
0.558
0.356
Dwg. MA-001-25A mm
NOTES: 1. Webbed lead frame. Leads 6, 7, 18, and 19 are internally one piece.
2. Lead thickness is measured at seating plane or below.
3. Lead spacing tolerance is non-cumulative.
4. Exact body and lead configuration at vendor’s option within limits shown.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
3961
DUAL FULL-BRIDGE
PWM MOTOR DRIVER
A3961SLB
Dimensions in Inches
(for reference only)
24
13
0.0125
0.0091
0.491
0.394
0.2992
0.2914
0.050
0.016
1
2
3
0.020
0.013
0.050
0.6141
0.5985
0° TO 8°
BSC
NOTE 1
NOTE 3
0.0926
0.1043
Dwg. MA-008-25 in
0.0040MIN
.
Dimensions in Millimeters
(controlling dimensions)
24
13
0.32
0.23
10.65
10.00
7.60
7.40
1.27
0.40
1
2
3
0.51
0.33
1.27
15.60
15.20
0° TO 8°
BSC
NOTE 1
NOTE 3
2.65
2.35
Dwg. MA-008-25A mm
0.10 MIN
.
NOTES: 1. Webbed lead frame. Leads 6, 7, 18, and 19 are internally one piece.
2. Lead spacing tolerance is non-cumulative.
3. Exact body and lead configuration at vendor’s option within limits shown.
3961
DUAL FULL-BRIDGE
PWM MOTOR DRIVER
BRIDGE & HALF-BRIDGE DRIVERS
SELECTION GUIDE
IN ORDER OF 1) OUTPUT CURRENT AND 2) OUTPUT VOLTAGE
Features
Output Ratings *
Internal
Diodes
Internal
Protection
Part
Number †
mA
V
Description
Outputs
±650
30
30
Dual PWM Full Bridge
Dual PWM Full Bridge
X
X
Bipolar
Bipolar
X
X
3966
3968
±750
45
45
45
Dual PWM Full Bridge
Dual PWM Full Bridge
Dual PWM Full Bridge
X
X
X
Bipolar
Bipolar
Bipolar
X
X
X
2916
2919
6219
±800
±900
33
14
7.0
50
Dual PWM Full Bridge
X
Bipolar
DMOS
NMOS
Bipolar
X
X
X
X
3964
3-Ø Back-EMF Controller/Driver
3-Ø Back-EMF Controller/Driver
PWM Full Bridge
X
X
X
8902-A
8984
±1000
±1300
±1500
3953
45
45
50
50
Dual PWM Full Bridge
Dual PWM Full Bridge
PWM Microstepping Full Bridge
PWM Microstepping Full Bridge
X
X
X
X
Bipolar
Bipolar
Darlington/Satlington™
Darlington/Satlington™
X
X
X
X
2917
2918
3955
3957
±2000
45
50
50
50
3-Ø Brushless Controller/Driver
Dual Full Bridge
PWM Full-Bridge
X
X
X
X
Darlington
Darlington
Darlington
Darlington
X
X
X
X
2936
2998
3951
3952
PWM Full-Bridge
±3000
±3400
±4000
45
45
14
PWM Control
X
X
X
Darlington
Bipolar
–
X
X
2962
2961
8925
PWM Control
3-Ø Brushless Controller/Driver
DMOS
*
Current is maximum specified test condition, voltage is maximum rating. See specification for sustaining voltage limits or over-
current protection voltage limits.
Complete part number includes additional characters to indicate operating temperature range and package style.
†
Allegro MicroSystems, Inc. reserves the right to make, from time to
time, such departures from the detail specifications as may be required to
permit improvements in the design of its products.
The information included herein is believed to be accurate and
reliable. However, Allegro MicroSystems, Inc. assumes no responsibility
for its use; nor for any infringements of patents or other rights of third
parties which may result from its use.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
相关型号:
©2020 ICPDF网 联系我们和版权申明