AM29F100B-150FC [AMD]
1 Megabit (128 K x 8-bit/64 K x 16-bit) CMOS 5.0 Volt-only, Boot Sector Flash Memory; 1兆位( 128千×8位/ 64千×16位) CMOS 5.0伏只,引导扇区闪存型号: | AM29F100B-150FC |
厂家: | AMD |
描述: | 1 Megabit (128 K x 8-bit/64 K x 16-bit) CMOS 5.0 Volt-only, Boot Sector Flash Memory |
文件: | 总36页 (文件大小:423K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
FINAL
Am29F100
1 Megabit (128 K x 8-bit/64 K x 16-bit)
CMOS 5.0 Volt-only, Boot Sector Flash Memory
DISTINCTIVE CHARACTERISTICS
■ Single power supply operation
■ Embedded Algorithms
— 5.0 V ± 10% for read, erase, and program
— Embedded Erase algorithm automatically
pre-programs and erases the chip or any
combination of designated sector
operations
— Simplifies system-level power requirements
— Embedded Program algorithm automatically
programs and verifies data at specified address
■ High performance
— 70 ns maximum access time
■ Minimum 100,000 program/erase cycles
■ Low power consumption
guaranteed
— 20 mA typical active read current for byte mode
— 28 mA typical active read current for word mode
— 30 mA typical program/erase current
— 25 µA typical standby current
■ Package options
— 44-pin SO
— 48-pin TSOP
■ Compatible with JEDEC standards
■ Flexible sector architecture
— Pinout and software compatible with
single-power-supply flash
— One 16 Kbyte, two 8 Kbyte, one 32 Kbyte, and
one 64 Kbyte sectors (byte mode)
— Superior inadvertent write protection
— One 8 Kword, two 4 Kword, one 16 Kword, and
one 32 Kword sectors (word mode)
■ Data# Polling and Toggle Bits
— Provides a software method of detecting
program or erase cycle completion
— Any combination of sectors can be erased
— Supports full chip erase
■ Ready/Busy pin (RY/BY#)
■ Top or bottom boot block configurations
— Provides a hardware method for detecting
program or erase cycle completion
available
■ Sector protection
■ Erase Suspend/Erase Resume
— Hardware-based feature that disables/re-
enables program and erase operations in any
combination of sectors
— Suspends an erase operation to read data from,
or program data to, a sector that is not being
erased, then resumes the erase operation
— Sector protection/unprotection can be
implemented using standard PROM
programming equipment
■ Hardware RESET# pin
— Hardware method of resetting the device to
reading array data
— Temporary Sector Unprotect feature allows in-
system code changes in protected sectors
Publication# 18926 Rev: C Amendment/+2
Issue Date: March 1998
GENERAL DESCRIPTION
The Am29F100 is a 1 Mbit, 5.0 Volt-only Flash memory
organized as 131,072 bytes or 65,536 words. The
Am29F100 is offered in 44-pin SO and 48-pin TSOP
packages. Word-wide data appears on DQ0-DQ15;
byte-wide data on DQ0-DQ7. The device is designed to
be programmed in-system with the standard system
device automatically times the erase pulse widths and
verifies proper cell margin.
The host system can detect whether a program or
erase operation is complete by observing the RY/BY#
pin, or by reading the DQ7 (Data# Polling) and DQ6
(toggle) status bits. After a program or erase cycle
has been completed, the device is ready to read array
data or accept another command.
5.0 Volt V
supply. A 12.0 volt V is not required for
CC
PP
program or erase operations. The device can also be
programmed or erased in standard EPROM program-
mers.
The Erase Suspend feature enables the system to put
erase on hold for any period of time to read data from,
or program data to, a sector that is not being erased.
The standard device offers access times of 70, 90,
120, and 150 ns, allowing high-speed microproces-
sors to operate without wait states. To eliminate bus
contention the device has separate chip enable
(CE#), write enable (WE#) and output enable (OE#)
controls.
The sector erase architecture allows memory sectors
to be erased and reprogrammed without affecting the
data contents of other sectors. The device is erased
when shipped from the factory.
The device requires only a single 5.0 volt power sup-
ply for both read and write functions. Internally gener-
ated and regulated voltages are provided for the
program and erase operations.
The hardware data protection measures include a
low VCC detector automatically inhibits write operations
during power transitions. The hardware sector pro-
tection feature disables both program and erase oper-
ations in any combination of the sectors of memory,
and is implemented using standard EPROM program-
mers. The temporary sector unprotect feature allows
in-system changes to protected sectors.
The device is entirely command set compatible with the
JEDEC single-power-supply Flash standard. Com-
mands are written to the command register using stan-
dard microprocessor write timings. Register contents
serve as input to an internal state machine that controls
the erase and programming circuitry. Write cycles also
internally latch addresses and data needed for the pro-
gramming and erase operations. Reading data out of
the device is similar to reading from other Flash or
EPROM devices.
The hardware RESET# pin terminates any operation
in progress and resets the internal state machine to
reading array data. The RESET# pin may be tied to the
system reset circuitry. A system reset would thus also
reset the device, enabling the system microprocessor
to read the boot-up firmware from the Flash memory.
Device programming occurs by executing the program
command sequence. This invokes the Embedded
Program algorithm—an internal algorithm that auto-
matically times the program pulse widths and verifies
proper cell margin.
The system can place the device into the standby mode.
Power consumption is greatly reduced in this mode.
AMD’s Flash technology combines years of Flash
memory manufacturing experience to produce the
highest levels of quality, reliability, and cost
effectiveness. The device electrically erases all bits
within a sector simultaneously via Fowler-Nordheim
tunneling. The bytes are programmed one byte at a
time using the EPROM programming mechanism of
hot electron injection.
Device erasure occurs by executing the erase com-
mand sequence. This invokes the Embedded Erase
algorithm—an internal algorithm that automatically pre-
programs the array (if it is not already programmed) be-
fore executing the erase operation. During erase, the
2
Am29F100
PRODUCT SELECTOR GUIDE
Family Part Number
Am29F100
Speed Option (V = 5.0 V ± 10%)
-70
70
70
30
-90
90
90
35
-120
120
120
50
-150
150
150
55
CC
Max Access Time (ns)
CE# Access (ns)
OE# Access (ns)
Note: See the AC Characteristics section for full specifications.
BLOCK DIAGRAM
DQ0–DQ15
RY/BY#
RY/BY#
Buffer
V
CC
Erase Voltage
Generator
Input/Output
Buffers
V
SS
State
Control
WE#
BYTE#
Command
Register
RESET#
PGM Voltage
Generator
Data
Latch
Chip Enable
Output Enable
Logic
STB
CE#
OE#
Y-Decoder
X-Decoder
Y-Gating
STB
V
Detector
Timer
CC
Cell Matrix
A0–A15
A-1
18926C-1
Am29F100
3
CONNECTION DIAGRAMS
NC
BYTE#
VSS
DQ15/A-1
DQ7
1
2
3
4
5
6
7
A15
A14
A13
A12
A11
A10
A9
A8
NC
NC
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
DQ14
DQ6
8
9
DQ13
DQ5
DQ12
DQ4
VCC
DQ11
DQ3
DQ10
DQ2
DQ9
DQ1
DQ8
DQ0
10
11
12
13
14
15
16
17
18
19
20
WE#
RESET#
NC
NC
RY/BY#
Standard TSOP
NC
NC
A7
A6
A5
A4
A3
21
22
23
24
OE#
VSS
CE#
A0
A2
A1
18926C-2
NC
BYTE#
VSS
1
2
3
4
5
6
7
A15
A14
A13
A12
A11
A10
A9
A8
NC
NC
WE#
RESET#
NC
NC
RY/BY#
NC
NC
A7
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
DQ15/A-1
DQ7
DQ14
DQ6
DQ13
DQ5
DQ12
DQ4
VCC
DQ11
DQ3
DQ10
DQ2
DQ9
DQ1
DQ8
DQ0
8
9
10
11
12
13
14
15
16
17
18
19
20
Reverse TSOP
A6
A5
A4
A3
A2
A1
OE#
VSS
CE#
A0
21
22
23
24
18926C-3
4
Am29F100
CONNECTION DIAGRAMS
NC
RY/BY#
NC
1
2
3
4
5
6
7
8
9
44 RESET#
43 WE#
42 A8
A7
41 A9
A6
40 A10
A5
39 A11
A4
38 A12
A3
37 A13
A2
36 A14
A1 10
A0 11
CE# 12
VSS 13
35 A15
34 NC
SO
33 BYTE#
32 VSS
OE# 14
DQ0 15
DQ8 16
DQ1 17
DQ9 18
DQ2 19
DQ10 20
DQ3 21
DQ11 22
31 DQ15/A-1
30 DQ7
29 DQ14
28 DQ6
27 DQ13
26 DQ5
25 DQ12
24 DQ4
23 VCC
18926C-4
PIN CONFIGURATION
LOGIC SYMBOL
A0–A15
= 16 Addresses
DQ0–DQ14= 15 Data Inputs/Outputs
16
DQ15/A-1 = DQ15 (Data Input/Output, word mode),
A-1 (LSB Address Input, byte mode)
A0–A15
CE#
16 or 8
DQ0–DQ15
(A-1)
CE#
= Chip Enable
OE#
= Output Enable
OE#
WE#
BYTE#
= Write Enable
WE#
= Selects 8-bit or 16-bit mode
RESET#
RESET# = Hardware Reset Pin, Active Low
BYTE#
RY/BY#
RY/BY#
VCC
= Ready/Busy Output
= +5.0 Volt Single Power Supply
(See Product Selector Guide for speed
options and voltage supply tolerances)
18926C-5
VSS
NC
= Device Ground
= Pin Not Connected Internally
Am29F100
5
ORDERING INFORMATION
Standard Products
AMD standard products are available in several packages and operating ranges. The order number (Valid Combination) is formed
by a combination of the elements below.
Am29F100
T
-70
E
C
B
OPTIONAL PROCESSING
Blank = Standard Processing
B
= Burn-In
(Contact an AMD representative for more infor-
mation.)
TEMPERATURE RANGE
C
I
=
=
=
Commercial (0°C to +70°C)
Industrial (–40°C to +85°C)
Extended (–55°C to +125°C)
E
PACKAGE TYPE
E
F
S
=
=
=
48-Pin Thin Small Outline Package
(TSOP) Standard Pinout (TS 048)
48-Pin Thin Small Outline Package
(TSOP) Reverse Pinout (TSR048)
44-Pin Small Outline Package
(SO 044)
SPEED OPTION
See Product Selector Guide and
Valid Combinations
BOOT CODE SECTOR ARCHITECTURE
T
B
=
=
Top sector
Bottom sector
DEVICE NUMBER/DESCRIPTION
Am29F100
1 Megabit (128 K x 8-Bit/64 K x 16-Bit) CMOS Flash Memory
5.0 Volt-only Read, Program, and Erase
Valid Combinations
Valid Combinations
Valid Combinations list configurations planned to be sup-
ported in volume for this device. Consult the local AMD sales
office to confirm availability of specific valid combinations and
to check on newly released combinations.
AM29F100T-70,
AM29F100B-70
AM29F100T-90,
AM29F100B-90
EC, EI, EE,
FC, FI, FE,
SC, SI, SE
AM29F100T-120,
AM29F100B-120
AM29F100T-150,
AM29F100B-150
6
Am29F100
DEVICE BUS OPERATIONS
This section describes the requirements and use of the
device bus operations, which are initiated through the
internal command register. The command register itself
does not occupy any addressable memory location.
The register is composed of latches that store the com-
mands, along with the address and data information
needed to execute the command. The contents of the
register serve as inputs to the internal state machine.
The state machine outputs dictate the function of the
device. The appropriate device bus operations table
lists the inputs and control levels required, and the re-
sulting output. The following subsections describe
each of these operations in further detail.
Table 1. Am29F100 Device Bus Operations
DQ8–DQ15
BYTE#
Addresses
(Note 1)
DQ0–
DQ7
BYTE#
Operation
CE#
L
OE# WE# RESET#
= V
= V
IH
IL
Read
L
H
X
H
X
H
L
H
A
D
D
OUT
IN
IN
OUT
DQ8–DQ14 = High-Z,
DQ15 = A-1
Write
L
H
A
D
D
IN
IN
Standby
V
± 0.5 V
X
H
X
V
± 0.5 V
X
High-Z
High-Z
High-Z
High-Z
High-Z
High-Z
High-Z
High-Z
High-Z
CC
CC
Output Disable
Hardware Reset
L
H
L
X
X
X
Temporary Sector
Unprotect
X
X
X
V
A
D
D
IN
High-Z
ID
IN
IN
Legend:
L = Logic Low = V , H = Logic High = V , V = 12.0 ± 0.5 V, X = Don’t Care, A = Addresses In, D = Data In, D = Data Out
IL
IH ID
IN
IN
OUT
Notes:
1. Addresses are A15:A0 in word mode (BYTE# = V ), A15:A-1 in byte mode (BYTE# = V ).
IH
IL
2. The sector protect and sector unprotect functions must be implemented via programming equipment. See the “Sector Pro-
tection/Unprotection” section.
memory content occurs during the power transition.
Word/Byte Configuration
No command is necessary in this mode to obtain
The BYTE# pin controls whether the device data I/O
array data. Standard microprocessor read cycles that
pins DQ15–DQ0 operate in the byte or word configura-
assert valid addresses on the device address inputs
tion. If the BYTE# pin is set at logic ‘1’, the device is in
produce valid data on the device data outputs. The
word configuration, DQ15–DQ0 are active and con-
device remains enabled for read access until the
trolled by CE# and OE#.
command register contents are altered.
If the BYTE# pin is set at logic ‘0’, the device is in byte
See “Reading Array Data” for more information. Refer
configuration, and only data I/O pins DQ0–DQ7 are ac-
to the AC Read Operations table for timing specifica-
tive and controlled by CE# and OE#. The data I/O pins
tions and to the Read Operations Timings diagram for
DQ8–DQ14 are tri-stated, and the DQ15 pin is used as
the timing waveforms. ICC1 in the DC Characteristics
an input for the LSB (A-1) address function.
table represents the active current specification for
reading array data.
Requirements for Reading Array Data
To read array data from the outputs, the system must
drive the CE# and OE# pins to VIL. CE# is the power
control and selects the device. OE# is the output control
and gates array data to the output pins. WE# should re-
main at VIH. The BYTE# pin determines whether the de-
vice outputs array data in words or bytes.
Writing Commands/Command Sequences
To write a command or command sequence (which in-
cludes programming data to the device and erasing
sectors of memory), the system must drive WE# and
CE# to VIL, and OE# to VIH.
For program operations, the BYTE# pin determines
whether the device accepts program data in bytes
or words. Refer to “Word/Byte Configuration” for
more information.
The internal state machine is set for reading array
data upon device power-up, or after a hardware re-
set. This ensures that no spurious alteration of the
Am29F100
7
An erase operation can erase one sector, multiple sec-
tors, or the entire device. The Sector Address Tables
indicate the address space that each sector occupies.
A “sector address” consists of the address bits required
to uniquely select a sector. See the “Command Defini-
tions” section for details on erasing a sector or the en-
tire chip, or suspending/resuming the erase operation.
If the device is deselected during erasure or program-
ming, the device draws active current until the
operation is completed.
In the DC Characteristics tables, ICC3 represents the
standby current specification.
RESET#: HARDWARE RESET PIN
After the system writes the autoselect command se-
quence, the device enters the autoselect mode. The
system can then read autoselect codes from the inter-
nal register (which is separate from the memory array)
on DQ7–DQ0. Standard read cycle timings apply in this
mode. Refer to the “Autoselect Mode” and “Autoselect
Command Sequence” sections for more information.
The RESET# pin provides a hardware method of reset-
ting the device to reading array data. When the system
drives the RESET# pin low for at least a period of tRP
,
the device immediately terminates any operation in
progress, tristates all data output pins, and ignores all
read/write attempts for the duration of the RESET#
pulse. The device also resets the internal state ma-
chine to reading array data. The operation that was in-
terrupted should be reinitiated once the device is ready
to accept another command sequence, to ensure data
integrity.
ICC2 in the DC Characteristics table represents the ac-
tive current specification for the write mode. The “AC
Characteristics” section contains timing specification
tables and timing diagrams for write operations.
Current is reduced for the duration of the RESET#
pulse. When RESET# is held at VIL, the device enters
Program and Erase Operation Status
During an erase or program operation, the system may
check the status of the operation by reading the status
bits on DQ7–DQ0. Standard read cycle timings and ICC
read specifications apply. Refer to “Write Operation
Status” for more information, and to each AC Charac-
teristics section for timing diagrams.
the TTL standby mode; if RESET# is held at VSS
0.5 V, the device enters the CMOS standby mode.
±
The RESET# pin may be tied to the system reset cir-
cuitry. A system reset would thus also reset the Flash
memory, enabling the system to read the boot-up firm-
ware from the Flash memory.
Standby Mode
If RESET# is asserted during a program or erase oper-
ation, the RY/BY# pin remains a “0” (busy) until the in-
ternal reset operation is complete, which requires a
time of tREADY (during Embedded Algorithms). The
system can thus monitor RY/BY# to determine whether
the reset operation is complete. If RESET# is asserted
when a program or erase operation is not executing
(RY/BY# pin is “1”), the reset operation is completed
within a time of tREADY (not during Embedded Algo-
rithms). The system can read data tRH after the RE-
SET# pin returns to VIH.
When the system is not reading or writing to the device,
it can place the device in the standby mode. In this
mode, current consumption is greatly reduced, and the
outputs are placed in the high impedance state, inde-
pendent of the OE# input.
The device enters the CMOS standby mode when CE#
and RESET# pins are both held at VCC ± 0.5 V. (Note
that this is a more restricted voltage range than VIH.)
The device enters the TTL standby mode when CE#
and RESET# pins are both held at VIH. The device re-
quires standard access time (tCE) for read access
when the device is in either of these standby modes,
before it is ready to read data.
Refer to the AC Characteristics tables for RESET# pa-
rameters and timing diagram.
Output Disable Mode
The device also enters the standby mode when the
RESET# pin is driven low. Refer to the next section,
“RESET#: Hardware Reset Pin”.
When the OE# input is at VIH, output from the device is
disabled. The output pins are placed in the high imped-
ance state.
8
Am29F100
Table 2. Sector Addresses Tables (Am29F100T)
A15
0
A14
X
A13
X
A12
X
(x8) Address Range
00000h-0FFFFh
10000h-17FFFh
18000h-19FFFh
1A000h-1BFFFh
1C000h-1FFFFh
(x16) Address Range
00000h-07FFFh
08000h-0BFFFh
0C000h-0CFFFh
0D000h-0DFFFh
0E000h-0FFFFh
SA0
SA1
SA2
SA3
SA4
1
0
X
X
1
1
0
0
1
1
0
1
1
1
1
X
Table 3. Sector Addresses Tables (Am29F100B)
A15
0
A14
0
A13
0
A12
X
(x8) Address Range
00000h-03FFFh
04000h-05FFFh
06000h-07FFFh
08000h-0FFFFh
10000h-1FFFFh
(x16) Address Range
00000h-01FFFh
02000h-02FFFh
03000h-03FFFh
04000h-07FFFh
08000h-0FFFFh
SA0
SA1
SA2
SA3
SA4
0
0
1
0
0
0
1
1
0
1
X
X
1
X
X
X
Autoselect Mode
The autoselect mode provides manufacturer and de-
vice identification, and sector protection verification,
through identifier codes output on DQ7–DQ0. This
mode is primarily intended for programming equipment
to automatically match a device to be programmed with
its corresponding programming algorithm. However,
the autoselect codes can also be accessed in-system
through the command register.
dress must appear on the appropriate highest order
address bits. Refer to the corresponding Sector Ad-
dress Tables. The Command Definitions table shows
the remaining address bits that are don’t care. When all
necessary bits have been set as required, the program-
ming equipment may then read the corresponding
identifier code on DQ7–DQ0.
To access the autoselect codes in-system, the host
system can issue the autoselect command via the
command register, as shown in the Command Defini-
tions table. This method does not require VID. See
“Command Definitions” for details on using the autose-
lect mode.
When using programming equipment, the autoselect
mode requires VID (11.5 V to 12.5 V) on address pin
A9. Address pins A6, A1, and A0 must be as shown in
Autoselect Codes (High Voltage Method) table. In ad-
dition, when verifying sector protection, the sector ad-
Table 4. Am29F100 Autoselect Codes (High Voltage Method)
A15 A11
to to
Mode CE# OE# WE# A12 A10 A9
A8
to
A7
A5
to
A2
DQ8
to
A0 DQ15
DQ7
to
DQ0
Description
A6
A1
Manufacturer ID: AMD
L
L
L
L
H
H
X
X
V
X
X
L
X
X
L
L
X
01h
D9h
ID
Device ID:
Am29F100
(Top Boot Block)
Word
Byte
Word
Byte
22h
X
X
V
L
L
L
L
H
ID
L
L
L
L
L
L
H
H
H
X
22h
X
D9h
DFh
DFh
Device ID:
Am29F100
(Bottom Boot Block)
X
X
X
V
V
X
X
X
X
H
L
ID
ID
01h
(protected)
X
X
Sector Protection Verification
L
L
H
SA
L
H
00h
(unprotected)
L = Logic Low = V , H = Logic High = V , SA = Sector Address, X = Don’t care.
IL
IH
Am29F100
9
Sector Protection/Unprotection
The hardware sector protection feature disables both
program and erase operations in any sector. The
hardware sector unprotection feature re-enables
both program and erase operations in previously pro-
tected sectors.
START
RESET# = V
(Note 1)
ID
Sector protection/unprotection must be implemented
using programming equipment. The procedure re-
quires a high voltage (VID) on address pin A9 and the
control pins. Details on this method are provided in a
supplement, publication number 20373. Contact an
AMD representative to obtain a copy of the appropriate
document.
Perform Erase or
Program Operations
RESET# = V
IH
The device is shipped with all sectors unprotected.
AMD offers the option of programming and protecting
sectors at its factory prior to shipping the device
through AMD’s ExpressFlash™ Service. Contact an
AMD representative for details.
Temporary Sector
Unprotect
Completed (Note 2)
It is possible to determine whether a sector is protected
or unprotected. See “Autoselect Mode” for details.
18926C-6
Notes:
1. All protected sectors unprotected.
Temporary Sector Unprotect
2. All previously protected sectors are protected once
again.
This feature allows temporary unprotection of previ-
ously protected sectors to change data in-system.
The Sector Unprotect mode is activated by setting the
RESET# pin to VID. During this mode, formerly pro-
tected sectors can be programmed or erased by se-
lecting the sector addresses. Once VID is removed
from the RESET# pin, all the previously protected
sectors are protected again. Figure 1 shows the algo-
rithm, and the Temporary Sector Unprotect (Figure
17) diagram shows the timing waveforms, for this fea-
ture.
Figure 1. Temporary Sector Unprotect Operation
10
Am29F100
proper signals to the control pins to prevent uninten-
Hardware Data Protection
tional writes when VCC is greater than VLKO
.
The command sequence requirement of unlock cycles
for programming or erasing provides data protection
against inadvertent writes (refer to the Command Defi-
nitions table). In addition, the following hardware data
protection measures prevent accidental erasure or pro-
gramming, which might otherwise be caused by spuri-
ous system level signals during VCC power-up and
power-down transitions, or from system noise.
Write Pulse “Glitch” Protection
Noise pulses of less than 5 ns (typical) on OE#, CE# or
WE# do not initiate a write cycle.
Logical Inhibit
Write cycles are inhibited by holding any one of OE#
= VIL, CE# = VIH or WE# = VIH. To initiate a write cy-
cle, CE# and WE# must be a logical zero while OE#
is a logical one.
Low V
Write Inhibit
CC
When VCC is less than VLKO, the device does not ac-
cept any write cycles. This protects data during VCC
power-up and power-down. The command register and
all internal program/erase circuits are disabled, and the
device resets. Subsequent writes are ignored until VCC
is greater than VLKO. The system must provide the
Power-Up Write Inhibit
If WE# = CE# = VIL and OE# = VIH during power
up, the device does not accept commands on the
rising edge of WE#. The internal state machine is
automatically reset to reading array data on
power-up.
COMMAND DEFINITIONS
Writing specific address and data commands or se-
quences into the command register initiates device op-
erations. The Command Definitions table defines the
valid register command sequences. Writing incorrect
address and data values or writing them in the im-
proper sequence resets the device to reading array
data.
See also “Requirements for Reading Array Data” in the
“Device Bus Operations” section for more information.
The Read Operations table provides the read parame-
ters, and Read Operation Timings diagram shows the
timing diagram.
Reset Command
Writing the reset command to the device resets the de-
vice to reading array data. Address bits are don’t care
for this command.
All addresses are latched on the falling edge of WE# or
CE#, whichever happens later. All data is latched on
the rising edge of WE# or CE#, whichever happens
first. Refer to the appropriate timing diagrams in the
“AC Characteristics” section.
The reset command may be written between the se-
quence cycles in an erase command sequence before
erasing begins. This resets the device to reading array
data. Once erasure begins, however, the device ig-
nores reset commands until the operation is complete.
Reading Array Data
The device is automatically set to reading array data
after device power-up. No commands are required to
retrieve data. The device is also ready to read array
data after completing an Embedded Program or Em-
bedded Erase algorithm.
The reset command may be written between the se-
quence cycles in a program command sequence be-
fore programming begins. This resets the device to
reading array data (also applies to programming in
Erase Suspend mode). Once programming begins,
however, the device ignores reset commands until the
operation is complete.
After the device accepts an Erase Suspend command,
the device enters the Erase Suspend mode. The sys-
tem can read array data using the standard read tim-
ings, except that if it reads at an address within erase-
suspended sectors, the device outputs status data.
After completing a programming operation in the Erase
Suspend mode, the system may once again read array
data with the same exception. See “Erase Suspend/
Erase Resume Commands” for more information on
this mode.
The reset command may be written between the se-
quence cycles in an autoselect command sequence.
Once in the autoselect mode, the reset command must
be written to return to reading array data (also applies
to autoselect during Erase Suspend).
If DQ5 goes high during a program or erase operation,
writing the reset command returns the device to read-
ing array data (also applies during Erase Suspend).
The system must issue the reset command to re-en-
able the device for reading array data if DQ5 goes high,
or while in the autoselect mode. See the “Reset Com-
mand” section, next.
Am29F100
11
Any commands written to the device during the Em-
bedded Program Algorithm are ignored. Note that a
hardware reset immediately terminates the program-
ming operation. The program command sequence
should be reinitiated once the device has reset to read-
ing array data, to ensure data integrity.
Autoselect Command Sequence
The autoselect command sequence allows the host
system to access the manufacturer and devices codes,
and determine whether or not a sector is protected.
The Command Definitions table shows the address
and data requirements. This method is an alternative to
that shown in the Autoselect Codes (High Voltage
Method) table, which is intended for PROM program-
mers and requires VID on address bit A9.
Programming is allowed in any sequence and across
sector boundaries. A bit cannot be programmed
from a “0” back to a “1”. Attempting to do so may halt
the operation and set DQ5 to “1”, or cause the Data#
Polling algorithm to indicate the operation was suc-
cessful. However, a succeeding read will show that the
data is still “0”. Only erase operations can convert a “0”
to a “1”.
The autoselect command sequence is initiated by
writing two unlock cycles, followed by the autoselect
command. The device then enters the autoselect
mode, and the system may read at any address any
number of times, without initiating another command
sequence.
A read cycle at address XX00h or retrieves the manu-
facturer code. A read cycle at address XX01h in word
mode (or 02h in byte mode) returns the device code.
A read cycle containing a sector address (SA) and the
address 02h in word mode (or 04h in byte mode) re-
turns 01h if that sector is protected, or 00h if it is un-
protected. Refer to the Sector Address tables for valid
sector addresses.
START
Write Program
Command Sequence
The system must write the reset command to exit the
autoselect mode and return to reading array data.
Data Poll
from System
Embedded
Program
algorithm
in progress
Word/Byte Program Command Sequence
The system may program the device by byte or word,
on depending on the state of the BYTE# pin. Program-
ming is a four-bus-cycle operation. The program com-
mand sequence is initiated by writing two unlock write
cycles, followed by the program set-up command. The
program address and data are written next, which in
turn initiate the Embedded Program algorithm. The
system is not required to provide further controls or tim-
ings. The device automatically provides internally gen-
erated program pulses and verify the programmed cell
margin. The Command Definitions take shows the ad-
dress and data requirements for the byte program com-
mand sequence.
Verify Data?
No
Yes
No
Increment Address
Last Address?
Yes
Programming
Completed
When the Embedded Program algorithm is complete,
the device then returns to reading array data and ad-
dresses are no longer latched. The system can deter-
mine the status of the program operation by using
DQ7, DQ6, or RY/BY#. See “Write Operation Status”
for information on these status bits.
18926C-7
Note: See the appropriate Command Definitions table for
program command sequence.
Figure 2. Program Operation
12
Am29F100
accepted, and erasure may begin. It is recommended
that processor interrupts be disabled during this time to
ensure all commands are accepted. The interrupts can
be re-enabled after the last Sector Erase command is
written. If the time between additional sector erase
commands can be assumed to be less than 50 µs, the
system need not monitor DQ3. Any command other
than Sector Erase or Erase Suspend during the
time-out period resets the device to reading array
data. The system must rewrite the command sequence
and any additional sector addresses and commands.
Chip Erase Command Sequence
Chip erase is a six-bus-cycle operation. The chip erase
command sequence is initiated by writing two unlock
cycles, followed by a set-up command. Two additional
unlock write cycles are then followed by the chip erase
command, which in turn invokes the Embedded Erase
algorithm. The device does not require the system to
preprogram prior to erase. The Embedded Erase algo-
rithm automatically preprograms and verifies the entire
memory for an all zero data pattern prior to electrical
erase. The system is not required to provide any con-
trols or timings during these operations. The Command
Definitions table shows the address and data require-
ments for the chip erase command sequence.
The system can monitor DQ3 to determine if the sector
erase timer has timed out. (See the “DQ3: Sector
Erase Timer” section.) The time-out begins from the ris-
ing edge of the final WE# pulse in the command se-
quence.
Any commands written to the chip during the Embed-
ded Erase algorithm are ignored. Note that a hardware
reset during the chip erase operation immediately ter-
minates the operation. The Chip Erase command se-
quence should be reinitiated once the device has
returned to reading array data, to ensure data integrity.
Once the sector erase operation has begun, only the
Erase Suspend command is valid. All other commands
are ignored. Note that a hardware reset during the
sector erase operation immediately terminates the op-
eration. The Sector Erase command sequence should
be reinitiated once the device has returned to reading
array data, to ensure data integrity.
The system can determine the status of the erase
operation by using DQ7, DQ6, or RY/BY#. See
“Write Operation Status” for information on these
status bits. When the Embedded Erase algorithm is
complete, the device returns to reading array data
and addresses are no longer latched.
When the Embedded Erase algorithm is complete, the
device returns to reading array data and addresses are
no longer latched. The system can determine the sta-
tus of the erase operation by using DQ7, DQ6, or RY/
BY#. Refer to “Write Operation Status” for information
on these status bits.
Figure 3 illustrates the algorithm for the erase opera-
tion. See the Erase/Program Operations tables in “AC
Characteristics” for parameters, and to the Chip/Sector
Erase Operation Timings for timing waveforms.
Figure 3 illustrates the algorithm for the erase opera-
tion. Refer to the Erase/Program Operations tables in
the “AC Characteristics” section for parameters, and to
the Sector Erase Operations Timing diagram for timing
waveforms.
Sector Erase Command Sequence
Sector erase is a six bus cycle operation. The sector
erase command sequence is initiated by writing two
unlock cycles, followed by a set-up command. Two ad-
ditional unlock write cycles are then followed by the ad-
dress of the sector to be erased, and the sector erase
command. The Command Definitions table shows the
address and data requirements for the sector erase
command sequence.
Erase Suspend/Erase Resume Commands
The Erase Suspend command allows the system to in-
terrupt a sector erase operation and then read data
from, or program data to, any sector not selected for
erasure. This command is valid only during the sector
erase operation, including the 50 µs time-out period
during the sector erase command sequence. The
Erase Suspend command is ignored if written during
the chip erase operation or Embedded Program algo-
rithm. Writing the Erase Suspend command during the
Sector Erase time-out immediately terminates the
time-out period and suspends the erase operation. Ad-
dresses are “don’t-cares” when writing the Erase Sus-
pend command.
The device does not require the system to preprogram
the memory prior to erase. The Embedded Erase algo-
rithm automatically programs and verifies the sector for
an all zero data pattern prior to electrical erase. The
system is not required to provide any controls or tim-
ings during these operations.
After the command sequence is written, a sector erase
time-out of 50 µs begins. During the time-out period,
additional sector addresses and sector erase com-
mands may be written. Loading the sector erase buffer
may be done in any sequence, and the number of sec-
tors may be from one sector to all sectors. The time be-
tween these additional cycles must be less than 50 µs,
otherwise the last address and command might not be
When the Erase Suspend command is written during a
sector erase operation, the device requires a maximum
of 20 µs to suspend the erase operation. However,
when the Erase Suspend command is written during
the sector erase time-out, the device immediately ter-
Am29F100
13
minates the time-out period and suspends the erase
operation.
Erase Suspend command can be written after the de-
vice has resumed erasing.
After the erase operation has been suspended, the
system can read array data from or program data to
any sector not selected for erasure. (The device “erase
suspends” all sectors selected for erasure.) Normal
read and write timings and command definitions apply.
Reading at any address within erase-suspended sec-
tors produces status data on DQ7–DQ0. The system
can use DQ7 to determine if a sector is actively erasing
or is erase-suspended. See “Write Operation Status”
for information on these status bits.
START
Write Erase
Command Sequence
Data Poll
from System
Embedded
After an erase-suspended program operation is com-
plete, the system can once again read array data within
non-suspended sectors. The system can determine the
status of the program operation using the DQ7 or DQ6
status bits, just as in the standard program operation.
See “Write Operation Status” for more information.
Erase
algorithm
in progress
No
Data = FFh?
The system may also write the autoselect command
sequence when the device is in the Erase Suspend
mode. The device allows reading autoselect codes
even at addresses within erasing sectors, since the
codes are not stored in the memory array. When the
device exits the autoselect mode, the device reverts to
the Erase Suspend mode, and is ready for another
valid operation. See “Autoselect Command Sequence”
for more information.
Yes
Erasure Completed
18926C-8
Notes:
1. See the appropriate Command Definitions table for erase
command sequence.
The system must write the Erase Resume command
(address bits are “don’t care”) to exit the erase suspend
mode and continue the sector erase operation. Further
writes of the Resume command are ignored. Another
2. See “DQ3: Sector Erase Timer” for more information.
Figure 3. Erase Operation
14
Am29F100
Table 5. Am29F100 Command Definitions
Bus Cycles (Notes 2–4)
Third Fourth
Addr Data Addr Data Addr Data Addr Data
Command
Sequence
(Note 1)
First
Addr Data Addr Data
RA RD
Second
Fifth
Sixth
Read (Note 5)
Reset (Note 6)
1
1
XXXX F0
Word
Byte
Word
Byte
Word
Byte
5555
AA
2AAA
5555
2AAA
5555
2AAA
5555
5555
AAAA
5555
Manufacturer ID
4
4
4
55
55
55
90 XX00
01
AAAA
5555
AA
XX01 22D9
XX02 D9
XX01 22DF
Device ID,
Top Boot Block
90
90
AAAA
AAAA
5555
5555
AA
Device ID,
Bottom Boot Block
AAAA
AAAA
XX02
DF
XX00
XX01
00
(SA)
X02
Word
Byte
5555
AA
2AAA
5555
5555
Sector Protect Verify
(Note 8)
4
55
90
(SA)
X04
AAAA
AAAA
01
Word
Byte
Word
Byte
Word
Byte
5555
AA
2AAA
5555
2AAA
5555
2AAA
5555
5555
AAAA
5555
Program
4
6
6
55
55
55
A0
80
80
PA
PD
AA
AA
AAAA
5555
AA
5555
AAAA
5555
2AAA
5555
2AAA
5555
5555
Chip Erase
55
55
10
30
AAAA
AAAA
5555
AAAA
5555
AA
Sector Erase
SA
AAAA
AAAA
AAAA
Erase Suspend (Note 9)
Erase Resume (Note 10)
1
1
XXXX B0
XXXX 30
Legend:
X = Don’t care
PD = Data to be programmed at location PA. Data latches on the
rising edge of WE# or CE# pulse, whichever happens first.
RA = Address of the memory location to be read.
SA = Address of the sector to be verified (in autoselect mode) or
erased. Address bits A15–A12 uniquely select any sector.
RD = Data read from location RA during read operation.
PA = Address of the memory location to be programmed.
Addresses latch on the falling edge of the WE# or CE# pulse,
whichever happens later.
Notes:
1. See Table 1 for description of bus operations.
7. The fourth cycle of the autoselect command sequence is a
read operation.
2. All values are in hexadecimal.
8. The data is 00h for an unprotected sector and 01h for a
protected sector. See “Autoselect Command Sequence” for
more information.
3. Except when reading array or autoselect data, all bus cycles
are write operations.
4. Data bits DQ15–DQ8 are don’t cares for unlock and
command cycles.
9. The system may read and program in non-erasing sectors, or
enter the autoselect mode, when in the Erase Suspend
mode. The Erase Suspend command is valid only during a
sector erase operation.
5. No unlock or command cycles required when reading array
data.
6. The Reset command is required to return to reading array
data when device is in the autoselect mode, or if DQ5 goes
high (while the device is providing status data).
10. The Erase Resume command is valid only during the Erase
Suspend mode.
Am29F100
15
WRITE OPERATION STATUS
The device provides several bits to determine the sta-
tus of a write operation: DQ3, DQ5, DQ6, DQ7, and
RY/BY#. Table 6 and the following subsections de-
scribe the functions of these bits. DQ7, RY/BY#, and
DQ6 each offer a method for determining whether a
program or erase operation is complete or in progress.
These three bits are discussed first.
Table 6 shows the outputs for Data# Polling on DQ7.
Figure 4 shows the Data# Polling algorithm.
START
DQ7: Data# Polling
Read DQ7–DQ0
Addr = VA
The Data# Polling bit, DQ7, indicates to the host
system whether an Embedded Algorithm is in
progress or completed, or whether the device is in
Erase Suspend. Data# Polling is valid after the ris-
ing edge of the final WE# pulse in the program or
erase command sequence.
Yes
DQ7 = Data?
During the Embedded Program algorithm, the device
outputs on DQ7 the complement of the datum pro-
grammed to DQ7. This DQ7 status also applies to pro-
gramming during Erase Suspend. When the
Embedded Program algorithm is complete, the device
outputs the datum programmed to DQ7. The system
must provide the program address to read valid status
information on DQ7. If a program address falls within a
protected sector, Data# Polling on DQ7 is active for ap-
proximately 2 µs, then the device returns to reading
array data.
No
No
DQ5 = 1?
Yes
Read DQ7–DQ0
Addr = VA
During the Embedded Erase algorithm, Data# Polling
produces a “0” on DQ7. When the Embedded Erase al-
gorithm is complete, or if the device enters the Erase
Suspend mode, Data# Polling produces a “1” on DQ7.
This is analogous to the complement/true datum output
described for the Embedded Program algorithm: the
erase function changes all the bits in a sector to “1”;
prior to this, the device outputs the “complement,” or
“0.” The system must provide an address within any of
the sectors selected for erasure to read valid status in-
formation on DQ7.
Yes
DQ7 = Data?
No
PASS
FAIL
After an erase command sequence is written, if all sec-
tors selected for erasing are protected, Data# Polling
on DQ7 is active for approximately 100 µs, then the de-
vice returns to reading array data. If not all selected
sectors are protected, the Embedded Erase algorithm
erases the unprotected sectors, and ignores the se-
lected sectors that are protected.
Notes:
1. VA = Valid address for programming. During a sector
erase operation, a valid address is an address within any
sector selected for erasure. During chip erase, a valid
address is any non-protected sector address.
2. DQ7 should be rechecked even if DQ5 = “1” because
DQ7 may change simultaneously with DQ5.
When the system detects DQ7 has changed from the
complement to true data, it can read valid data at DQ7–
18926C-9
following read cycles. This is because DQ7
DQ0 on the
Figure 4. Data# Polling Algorithm
may change asynchronously with DQ0–DQ6 while
Output Enable (OE#) is asserted low. The Data# Poll-
ing Timings (During Embedded Algorithms) figure in
the “AC Characteristics” section illustrates this.
16
Am29F100
system would note and store the value of the toggle
bit after the first read. After the second read, the sys-
tem would compare the new value of the toggle bit
with the first. If the toggle bit is not toggling, the device
has completed the program or erase operation. The
system can read array data on DQ7–DQ0 on the fol-
lowing read cycle.
RY/BY#: Ready/Busy#
The RY/BY# is a dedicated, open-drain output pin that
indicates whether an Embedded Algorithm is in
progress or complete. The RY/BY# status is valid after
the rising edge of the final WE# pulse in the command
sequence. Since RY/BY# is an open-drain output, sev-
eral RY/BY# pins can be tied together in parallel with a
pull-up resistor to VCC
.
However, if after the initial two read cycles, the system
determines that the toggle bit is still toggling, the
system also should note whether the value of DQ5 is
high (see the section on DQ5). If it is, the system
should then determine again whether the toggle bit is
toggling, since the toggle bit may have stopped tog-
gling just as DQ5 went high. If the toggle bit is no longer
toggling, the device has successfully completed the
program or erase operation. If it is still toggling, the
device did not complete the operation successfully, and
the system must write the reset command to return to
reading array data.
If the output is low (Busy), the device is actively erasing
or programming. (This includes programming in the
Erase Suspend mode.) If the output is high (Ready),
the device is ready to read array data (including during
the Erase Suspend mode), or is in the standby mode.
Table 6 shows the outputs for RY/BY#. The timing dia-
grams for read, reset, program, and erase shows the
relationship of RY/BY# to other signals.
DQ6: Toggle Bit I
Toggle Bit I on DQ6 indicates whether an Embedded
Program or Erase algorithm is in progress or complete,
or whether the device has entered the Erase Suspend
mode. Toggle Bit I may be read at any address, and is
valid after the rising edge of the final WE# pulse in the
command sequence (prior to the program or erase op-
eration), and during the sector erase time-out.
The remaining scenario is that the system initially de-
termines that the toggle bit is toggling and DQ5 has not
gone high. The system may continue to monitor the
toggle bit and DQ5 through successive read cycles, de-
termining the status as described in the previous para-
graph. Alternatively, it may choose to perform other
system tasks. In this case, the system must start at the
beginning of the algorithm when it returns to determine
the status of the operation (top of Figure 5).
During an Embedded Program or Erase algorithm op-
eration, successive read cycles to any address cause
DQ6 to toggle. (The system may use either OE# or
CE# to control the read cycles.) When the operation is
complete, DQ6 stops toggling.
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program or erase time has
exceeded a specified internal pulse count limit. Under
these conditions DQ5 produces a “1.” This is a failure
condition that indicates the program or erase cycle was
not successfully completed.
After an erase command sequence is written, if all
sectors selected for erasing are protected, DQ6 tog-
gles for approximately 100 µs, then returns to reading
array data. If not all selected sectors are protected,
the Embedded Erase algorithm erases the unpro-
tected sectors, and ignores the selected sectors that
are protected.
The DQ5 failure condition may appear if the system
tries to program a “1” to a location that is previously
programmed to “0.” Only an erase operation can
change a “0” back to a “1.” Under this condition, the
device halts the operation, and when the operation has
exceeded the timing limits, DQ5 produces a “1.”
If a program address falls within a protected sector,
DQ6 toggles for approximately 2 µs after the program
command sequence is written, then returns to reading
array data.
Under both these conditions, the system must issue
the reset command to return the device to reading
array data.
DQ6 also toggles during the erase-suspend-program
mode, and stops toggling once the Embedded Pro-
gram algorithm is complete.
DQ3: Sector Erase Timer
The Write Operation Status table shows the outputs for
Toggle Bit I on DQ6. Refer to Figure 5 for the toggle bit
algorithm, and to the Toggle Bit Timings figure in the
“AC Characteristics” section for the timing diagram.
After writing a sector erase command sequence, the
system may read DQ3 to determine whether or not an
erase operation has begun. (The sector erase timer
does not apply to the chip erase command.) If addi-
tional sectors are selected for erasure, the entire time-
out also applies after each additional sector erase
command. When the time-out is complete, DQ3
switches from “0” to “1.” The system may ignore DQ3
if the system can guarantee that the time between ad-
ditional sector erase commands will always be less
Reading Toggle Bit DQ6
Refer to Figure 5 for the following discussion. When-
ever the system initially begins reading toggle bit sta-
tus, it must read DQ7–DQ0 at least twice in a row to
determine whether a toggle bit is toggling. Typically, a
Am29F100
17
than 50 µs. See also the “Sector Erase Command Se-
quence” section.
After the sector erase command sequence is written,
the system should read the status on DQ7 (Data# Poll-
ing) or DQ6 (Toggle Bit I) to ensure the device has ac-
cepted the command sequence, and then read DQ3. If
DQ3 is “1”, the internally controlled erase cycle has be-
gun; all further commands (other than Erase Suspend)
are ignored until the erase operation is complete. If
DQ3 is “0”, the device will accept additional sector
erase commands. To ensure the command has been
accepted, the system software should check the status
of DQ3 prior to and following each subsequent sector
erase command. If DQ3 is high on the second status
check, the last command might not have been ac-
cepted. Table 6 shows the outputs for DQ3.
START
Read DQ7–DQ0
Read DQ7–DQ0
1
No
Toggle Bit
= Toggle?
Yes
No
DQ5 = 1?
Yes
(Notes
1, 2)
Read DQ7–DQ0
Twice
Toggle Bit
= Toggle?
No
Yes
Program/Erase
Operation Not
Complete, Write
Reset Command
Program/Erase
Operation Complete
Notes:
1. Read toggle bit twice to determine whether or not it is
toggling. See text.
2. Recheck toggle bit because it may stop toggling as DQ5
changes to “1”. See text.
18926C-10
Figure 5. Toggle Bit Algorithm
18
Am29F100
Table 6. Write Operation Status
DQ7
DQ5
Operation
(Note 1)
DQ7#
0
DQ6
(Note 2)
DQ3
N/A
1
RY/BY#
Embedded Program Algorithm
Embedded Erase Algorithm
Toggle
Toggle
0
0
0
0
Standard
Mode
Reading within Erase
Suspended Sector
1
No toggle
0
N/A
1
Erase
Suspend
Mode
Reading within Non-Erase Suspended
Sector
Data
Data
Data
0
Data
N/A
1
0
Erase-Suspend-Program
DQ7#
Toggle
Notes:
1. DQ7 requires a valid address when reading status information. Refer to the appropriate subsection for further details.
2. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits.
See “DQ5: Exceeded Timing Limits” for more information.
Am29F100
19
ABSOLUTE MAXIMUM RATINGS
Storage Temperature
Plastic Packages . . . . . . . . . . . . . . . –65°C to +125°C
20 ns
20 ns
+0.8 V
Ambient Temperature
with Power Applied . . . . . . . . . . . . . –55°C to +125°C
–0.5 V
–2.0 V
Voltage with Respect to Ground
VCC (Note 1). . . . . . . . . . . . . . . . . . . .–2.0 V to +7.0 V
A9 (Note 2). . . . . . . . . . . . . . . . . . . .–2.0 V to +13.5 V
All other pins (Note 1) . . . . . . . . . . . .–2.0 V to +7.0 V
Output Short Circuit Current (Note 3) . . . . . . 200 mA
20 ns
18926C-11
Notes:
Figure 6. Maximum Negative Overshoot
Waveform
1. Minimum DC voltage on input or I/O pin is –0.5 V. During
voltage transitions, inputs may overshoot V to –2.0 V
SS
for periods of up to 20 ns. See Figure 6. Maximum DC
voltage on input and I/O pins is V + 0.5 V. During volt-
CC
age transitions, input and I/O pins may overshoot to V
+ 2.0 V for periods up to 20 ns. See Figure 7.
CC
20 ns
2. Minimum DC input voltage on A9 pin is –0.5V. During
V
voltage transitions, A9 pins may overshoot V to –2.0 V
CC
SS
+2.0 V
V
+0.5 V
for periods of up to 20 ns. See Figure 6. Maximum DC in-
put voltage on A9 is +12.5 V which may overshoot to 13.5
V for periods up to 20 ns.
CC
3. No more than one output shorted at a time. Duration of
the short circuit should not be greater than one second.
2.0 V
20 ns
20 ns
Stresses above those listed under “Absolute Maximum Rat-
ings” may cause permanent damage to the device. This is a
stress rating only; functional operation of the device at these
or any other conditions above those indicated in the opera-
tional sections of this specification is not implied. Exposure of
the device to absolute maximum rating conditions for ex-
tended periods may affect device reliability.
18926C-12
Figure 7. Maximum Positive Overshoot
Waveform
OPERATING RANGES
Commercial (C) Devices
Case Temperature (TA) . . . . . . . . . . . . . 0°C to +70°C
Industrial (I) Devices
Case Temperature (TA) . . . . . . . . . . . –40°C to +85°C
Extended (E) Devices
Case Temperature (TA) . . . . . . . . . . –55°C to +125°C
V
Supply Voltages
CC
VCC for all devices . . . . . . . . . . . . .+4.50 V to +5.50 V
Operating ranges define those limits between which the
functionality of the device is guaranteed.
20
Am29F100
DC CHARACTERISTICS
TTL/NMOS Compatible
Parameter
Symbol
Parameter Description
Test Description
= V to V , V = V Max
Min
Max
±1.0
50
Unit
µA
µA
µA
mA
mA
mA
mA
V
I
Input Load Current
V
V
V
LI
IN
SS
CC
CC
CC
I
A9 Input Load Current
Output Leakage Current
= V Max, A9 = 12.5 V
LIT
CC
OUT
CC
I
= V to V , V = V Max
±1.0
40
LO
SS
CC
CC
CC
Byte
V
= V Max, CE# = V
CC IL,
CC
I
V
Active Current (Note 1)
CC1
CC
OE# = V
IH
Word
50
I
I
V
V
Active Current (Notes 2, 3)
Standby Current
V
V
= V Max, CE# = V OE# = V
IH
60
CC2
CC3
CC
CC
CC
IL,
V
Max, CE#
V
, OE# = V
IH
1.0
0.8
CC
CC = CC
=
IH
V
Input Low Voltage
–0.5
2.0
IL
V
Input High Voltage
V
+ 0.5
V
IH
CC
Voltage for Autoselect and
Temporary Sector Unprotect
V
V
= 5.0 V
11.5
12.5
0.45
V
ID
CC
V
Output Low Voltage
Output High Voltage
I
I
= 5.8 mA, V = V Min
V
V
V
OL
OL
CC
CC
V
= –2.5 mA, V = V Min
2.4
3.2
OH
OH
CC
CC
V
Low V Lock-out Voltage
4.2
LKO
CC
Notes:
1. The I current listed is typically less than 2 mA/MHz, with OE# at V .
CC
IH
2. I active while Embedded Program or Embedded Erase Algorithm is in progress.
CC
3. Not 100% tested.
Am29F100
21
DC CHARACTERISTICS (continued)
CMOS Compatible
Parameter
Symbol
Parameter Description
Input Load Current
Test Description
= V to V , V = V Max
Min
Max
±1.0
50
Unit
µA
I
V
V
V
LI
IN
SS
CC
CC
CC
I
A9 Input Load Current
Output Leakage Current
= V Max, A9 = 12.5 V
µA
LIT
CC
OUT
CC
I
= V to V , V = V Max
±1.0
40
µA
LO
SS
CC
CC
CC
Byte
V
= V Max,
CC
CC
I
I
V
V
Active Current (Note 1)
mA
mA
CC1
CC2
CC
CC
CE# = V OE# = V
IL,
IH
Word
50
Active Current (Notes 2, 3)
V
V
= V Max, CE# = V OE# = V
IH
60
CC
CC
CC
IL,
= V Max, OE# = V
CC
IH,
I
V
Standby Current
CE# and RESET# = V ± 0.5 V
100
µA
CC3
CC
CC
V
Input Low Voltage
–0.5
0.8
V
V
IL
V
Input High Voltage
0.7 x V
V
+ 0.5
IH
CC
CC
Voltage for Autoselect and
Temporary Sector Unprotect
V
V
= 5.0 V
CC
11.5
12.5
0.45
V
ID
V
Output Low Voltage
I
I
I
= 5.8 mA, V = V Min
V
V
V
V
OL
OL
OH
OH
CC
CC
V
V
V
= –2.5 mA, V = V Min
0.85 V
OH1
OH2
LKO
CC
CC
CC
Output High Voltage
= –100 µA, V = V Min
V
–0.4
CC
CC
CC
Low V Lock-out Voltage
3.2
4.2
CC
Notes:
1. The I current listed is typically less than 2 mA/MHz, with OE# at V .
CC
IH
2. I active while Embedded Program or Embedded Erase Algorithm is in progress.
CC
3. Not 100% tested.
22
Am29F100
TEST CONDITIONS
Table 7. Test Specifications
5.0 V
Test Condition
-70
All others Unit
Output Load
1 TTL gate
100
2.7 kΩ
Device
Under
Test
Output Load Capacitance, C
(including jig capacitance)
L
30
5
pF
C
L
Input Rise and Fall Times
Input Pulse Levels
20
ns
6.2 kΩ
0.0–3.0 0.45–2.4
V
Input timing measurement
reference levels
1.5
1.5
0.8
2.0
V
V
Output timing measurement
reference levels
Note: Diodes are IN3064 or equivalent
18926C-13
Figure 8. Test Setup
KEY TO SWITCHING WAVEFORMS
WAVEFORM
INPUTS
OUTPUTS
Steady
Changing from H to L
Changing from L to H
Don’t Care, Any Change Permitted
Does Not Apply
Changing, State Unknown
Center Line is High Impedance State (High Z)
KS000010-PAL
Am29F100
23
AC CHARACTERISTICS
Read-only Operations Characteristics
Parameter
Symbol
JEDEC
Std.
Parameter Description
Read Cycle Time (Note 1)
Test Setup
-70
-90
-120 -150 Unit
t
t
Min
70
90
120
120
150
150
ns
ns
AVAV
RC
CE# = V
IL
t
t
t
Address to Output Delay
Max
70
90
AVQV
ACC
OE# = V
IL
t
t
Chip Enable to Output Delay
OE# = V
Max
Max
Max
70
30
20
90
35
20
120
50
150
55
ns
ns
ns
ELQV
GLQV
EHQZ
CE
IL
t
t
Output Enable to Output Delay
Chip Enable to Output High Z (Notes 1, 2)
OE
t
30
35
DF
DF
Output Enable to Output High Z
(Notes 1, 2)
t
t
Max
Min
Min
20
20
30
35
ns
ns
ns
GHQZ
Read
0
t
Output Enable Hold Time (Note 1)
OEH
Toggle and Data
Polling
10
Output Hold Time From Addresses CE# or
OE#, Whichever Occurs First
t
t
Min
0
ns
AXQX
OH
Notes:
1. Not 100% tested.
2. Output Driver Disable Time.
3. See Figure 8 and Table 7 for test specifications.
tRC
Addresses Stable
Addresses
CE#
tACC
tDF
tOE
OE#
tOEH
WE#
tCE
tOH
HIGH Z
HIGH Z
Output Valid
Outputs
RESET#
RY/BY#
0 V
18926C-14
Figure 9. Read Operations Timings
24
Am29F100
AC CHARACTERISTICS
Hardware Reset (RESET#)
Parameter
JEDEC
Std Description
Test Setup
All Speed Options
Unit
RESET# Pin Low (During Embedded
Algorithms) to Read or Write (See Note)
t
t
Max
20
µs
READY
READY
RESET# Pin Low (NOT During Embedded
Algorithms) to Read or Write (See Note)
Max
500
ns
t
t
t
RESET# Pulse Width
Min
Min
Min
500
50
0
ns
ns
ns
RP
RH
RB
RESET# High Time Before Read (See Note)
RY/BY# Recovery Time
Note: Not 100% tested.
RY/BY#
CE#, OE#
RESET#
tRH
tRP
tReady
Reset Timings NOT during Embedded Algorithms
Reset Timings during Embedded Algorithms
tReady
RY/BY#
tRB
CE#, OE#
RESET#
tRP
18926C-15
Figure 10. RESET# Timings
Am29F100
25
AC CHARACTERISTICS
Word/Byte Configuration (BYTE#)
Parameter
JEDEC
Std.
Description
-70
-90
-120
-150 Unit
t
t
t
t
CE# to BYTE# Switching Low or High
BYTE# Switching Low to Output HIGH Z
BYTE# Switching High to Output Active
Max
Max
Min
5
ns
ELFL/ ELFH
20
70
20
90
30
35
ns
ns
FLQZ
FHQV
120
150
CE#
OE#
BYTE#
t
ELFL
Data Output
(DQ0–DQ14)
Data Output
(DQ0–DQ7)
BYTE#
Switching
from word
to byte
DQ0–DQ14
DQ15/A-1
Address
Input
DQ15
Output
mode
t
FLQZ
t
ELFH
BYTE#
BYTE#
Switching
from byte
to word
Data Output
(DQ0–DQ7)
Data Output
(DQ0–DQ14)
DQ0–DQ14
DQ15/A-1
mode
Address
Input
DQ15
Output
t
FHQV
18926C-16
Figure 11. BYTE# Timings for Read Operations
CE#
The falling edge of the last WE# signal
WE#
BYTE#
t
SET
(t
)
AS
t
(t
)
HOLD AH
Note:
Refer to the Erase/Program Operations table for t and t specifications.
AS
AH
18926C-17
Figure 12. BYTE# Timings for Write Operations
26
Am29F100
AC CHARACTERISTICS
Erase and Program Operations
Parameter Symbol
JEDEC
Standard
Parameter Description
Write Cycle Time (Note 1)
-70
-90
-120
-150 Unit
t
t
Min
Min
Min
Min
Min
70
90
120
150
ns
ns
ns
ns
ns
AVAV
WC
t
t
Address Setup Time
Address Hold Time
Data Setup Time
Data Hold Time
0
AVWL
WLAX
AS
AH
DS
DH
t
t
45
30
45
45
50
50
50
50
t
t
t
t
DVWH
WHDX
0
0
Read Recover Time Before Write
(OE# High to WE# Low)
t
t
Min
ns
GHWL
GHWL
t
t
t
CE# Setup Time
Min
Min
Min
Min
Typ
Typ
Min
Min
Min
0
0
ns
ns
ns
ns
µs
sec
µs
ns
ns
ELWL
WHEH
WLWH
WHWL
CS
CH
WP
t
CE# Hold Time
t
t
t
Write Pulse Width
35
45
50
50
t
Write Pulse Width High
Byte Programming Operation (Note 2)
Chip/Sector Erase Operation (Note 2)
20
14
1.5
50
0
WPH
t
t
t
t
WHWH1
WHWH2
WHWH1
WHWH2
t
V
Set Up Time (Note 1)
CC
VCS
t
Recovery Time from RY/BY#
RB
t
Program/Erase Valid to RY/BY# Delay
30
35
50
55
BUSY
Notes:
1. Not 100% tested.
2. See the “Erase and Programming Performance” section for more information.
Am29F100
27
AC CHARACTERISTICS
Program Command Sequence (last two cycles)
Read Status Data (last two cycles)
tAS
tWC
Addresses
555h
PA
PA
PA
tAH
CE#
OE#
tCH
tGHWL
tWHWH1
tWP
WE#
Data
tWPH
tCS
tDS
tDH
PD
DOUT
A0h
Status
tBUSY
tRB
RY/BY#
VCC
tVCS
18926C-13
Notes:
1. PA = program address, PD = program data, D
is the true data at the program address.
OUT
2. Illustration shows device in word mode.
Figure 13. Program Operation Timings
Erase Command Sequence (last two cycles)
Read Status Data
VA
tAS
tWC
VA
Addresses
CE#
2AAh
SA
555h for chip erase
tAH
tGHWL
tCH
OE#
tWP
WE#
tWPH
tWHWH2
tCS
tDS
tDH
In
Data
Complete
55h
30h
Progress
10 for Chip Erase
tBUSY
tRB
RY/BY#
VCC
tVCS
18926C-13
Notes:
1. SA = sector address (for Sector Erase), VA = Valid Address for reading status data (see “Write Operation Status”).
2. Illustration shows device in word mode.
Figure 14. Chip/Sector Erase Operation Timings
28
Am29F100
AC CHARACTERISTICS
tRC
VA
Addresses
VA
VA
tACC
tCE
CE#
tCH
tOE
OE#
WE#
tOEH
tDF
tOH
High Z
High Z
DQ7
Valid Data
Complement
Complement
True
DQ0–DQ6
Valid Data
Status Data
True
Status Data
tBUSY
RY/BY#
Note: VA = Valid address. Illustration shows first status cycle after command sequence, last status read cycle, and array data
read cycle.
18926C-18
Figure 15. Data# Polling Timings (During Embedded Algorithms)
tRC
Addresses
CE#
VA
tACC
tCE
VA
VA
VA
tCH
tOE
OE#
WE#
tOEH
tDF
tOH
High Z
DQ6
Valid Status
(first read)
Valid Status
Valid Status
Valid Data
(second read)
(stops toggling)
tBUSY
RY/BY#
Note: VA = Valid address; not required for DQ6. Illustration shows first two status cycle after command sequence, last status read
cycle, and array data read cycle.
18926C-19
Figure 16. Toggle Bit Timings (During Embedded Algorithms)
Am29F100
29
AC CHARACTERISTICS
Temporary Sector Unprotect
Parameter
JEDEC
Std.
Description
Rise and Fall Time (See Note)
All Speed Options
Unit
t
V
Min
Min
500
ns
VIDR
ID
RESET# Setup Time for Temporary Sector
Unprotect
t
4
µs
RSP
Note: Not 100% tested.
12 V
RESET#
0 or 5 V
0 or 5 V
tVIDR
tVIDR
Program or Erase Command Sequence
CE#
WE#
tRSP
RY/BY#
18926C-20
Figure 17. Temporary Sector Unprotect Timing Diagram
30
Am29F100
AC CHARACTERISTICS
Erase and Program Operations
Alternate CE# Controlled Writes
Parameter Symbol
JEDEC
Standard
Parameter Description
Write Cycle Time (Note 1)
-70
-90
-120
-150
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
µs
sec
t
t
t
Min
Min
Min
Min
Min
Min
Min
Min
Min
Min
Min
Typ
Typ
70
90
120
150
AVAV
AVEL
ELAX
WC
t
Address Setup Time
0
AS
AH
DS
DH
t
t
Address Hold Time
45
30
45
45
50
50
50
50
t
t
t
t
Data Setup Time
DVEH
EHDX
Data Hold Time
0
0
0
0
0
t
Output Enable Setup Time
Read Recover Time Before Write
WE# Setup Time
OES
t
t
t
GHEL
GHEL
WLEL
t
WS
WH
t
t
WE# Hold Time
EHWH
t
t
CE# Pulse Width
35
45
50
50
ELEH
EHEL
CP
t
t
CE# Pulse Width High
Byte Programming Operation (Note 2)
Chip/Sector Erase Operation (Note 2)
20
14
CPH
t
t
t
t
WHWH1
WHWH2
WHWH1
WHWH2
1.5
Notes:
1. Not 100% tested.
2. See the “Erase and Programming Performance” section for more information.
Am29F100
31
AC CHARACTERISTICS
555 for program
PA for program
2AA for erase
SA for sector erase
555 for chip erase
Data# Polling
Addresses
PA
tWC
tWH
tAS
tAH
WE#
OE#
tGHEL
tWHWH1 or 2
tCP
CE#
Data
tWS
tCPH
tDS
tBUSY
tDH
DQ7#
DOUT
tRH
A0 for program
55 for erase
PD for program
30 for sector erase
10 for chip erase
RESET#
RY/BY#
Notes:
1. PA = Program Address, PD = Program Data, SA = Sector Address, DQ7# = Complement of Data Input, D
= Array Data.
18926C-21
OUT
2. Figure indicates the last two bus cycles of the command sequence, with the device in word mode.
Figure 18. Alternate CE# Controlled Write Operation Timings
32
Am29F100
ERASE AND PROGRAMMING PERFORMANCE
Limits
Parameter
Typ (Note 1)
Max (Note 2)
Unit
Comments
Excludes 00h programming prior to
erasure (Note 4)
Chip/Sector Erase Time
1.5
15
sec
Byte Programming Time
14
28
1000
2000
12.5
µs
µs
Excludes system-level overhead
(Note 5)
Word Programming Time
Chip Programming Time (Note 3)
1.8
sec
Notes:
1. Typical program and erase times assume the following conditions: 25°C, 5.0 V V , 100,000 cycles. Additionally,
CC
programming typicals assume checkerboard pattern.
2. Under worst case conditions of 90°C, V = 4.5 V, 100,000 cycles.
CC
3. The typical chip programming time is considerably less than the maximum chip programming time listed, since most bytes
program faster than the maximum byte program time listed. If the maximum byte program time given is exceeded, only then
does the device set DQ5 = 1. See the section on DQ5 for further information.
4. In the pre-programming step of the Embedded Erase algorithm, all bytes are programmed to 00h before erasure.
5. System-level overhead is the time required to execute the four-bus-cycle command sequence for programming. See Table 1
for further information on command definitions.
6. The device has a guaranteed minimum erase and program cycle endurance of 100,000 cycles.
LATCHUP CHARACTERISTIC
Parameter Description
Input Voltage with respect to V on I/O pins
Min
Max
+ 1.0 V
–1.0 V
V
CC
SS
V
Current
–100 mA
+100 mA
CC
Note: Includes all pins except V . Test conditions: V = 5.0 Volt, one pin at a time.
CC
CC
TSOP AND SO PIN CAPACITANCE
Parameter
Symbol
Parameter Description
Input Capacitance
Test Conditions
Typ
6
Max
7.5
12
Unit
pF
C
V
V
V
= 0
IN
IN
C
Output Capacitance
= 0
= 0
8.5
8
pF
OUT
OUT
C
Control Pin Capacitance
10
pF
IN2
IN
Notes:
1. Sampled, not 100% tested.
2. Test conditions T = 25°C, f = 1.0 MHz.
A
DATA RETENTION
Parameter Description
Test Conditions
150°C
Min
10
Unit
Years
Years
Minimum Pattern Data Retention Time
125°C
20
Am29F100
33
PHYSICAL DIMENSIONS
SO 044—44-Pin Small Outline Package (measured in millimeters)
44
23
13.10
13.50
15.70
16.30
1
22
1.27 NOM.
TOP VIEW
28.00
28.40
0.10
0.21
2.17
2.45
2.80
MAX.
0°
8°
SEATING
PLANE
0.60
1.00
0.35
0.50
0.10
0.35
END VIEW
SIDE VIEW
16-038-SO44-2
SO 044
DF83
8-8-96 lv
34
Am29F100
PHYSICAL DIMENSIONS
TS 048—48-Pin Standard Thin Small Outline Package (measured in millimeters)
0.95
1.05
Pin 1 I.D.
1
48
11.90
12.10
0.50 BSC
24
25
0.05
0.15
18.30
18.50
19.80
20.20
16-038-TS48-2
TS 048
DT95
0.08
0.20
0.10
0.21
1.20
MAX
8-8-96 lv
0°
5°
0.25MM (0.0098") BSC
0.50
0.70
TSR048—48-Pin Reverse Thin Small Outline Package (measured in millimeters)
0.95
1.05
Pin 1 I.D.
1
48
11.90
12.10
0.50 BSC
24
25
0.05
0.15
18.30
18.50
19.80
20.20
SEATING PLANE
16-038-TS48
TSR048
DT95
0.08
0.20
8-8-96 lv
1.20
MAX
0.10
0.21
0°
5°
0.25MM (0.0098") BSC
0.50
0.70
Am29F100
35
REVISION SUMMARY FOR AM29F100
Revision B+1
chip/sector erase times (tWHWH1 and tWHWH2, respec-
tively).
Product Selector Guide
Erase and Programming Performance
Replaced the -75 column (70 ns, ±5%) with the -70 col-
umn (70 ns, ±10%).
Combined sector and chip erase times, added word
programming times and erase/program cycle times.
Updated specifications.
Ordering Information, Standard Products
The -70 designation is now listed in the part number ex-
ample.
Revision C
Global
Valid Combinations: Replaced the -75 combinations
with -70. The 70 ns speed grade is now available in the
same combinations as the other speed grades.
Made formatting and layout consistent with other data
sheets. Used updated common tables and diagrams.
Operating Ranges
Revision C+1
VCC Supply Voltages: Changed the -75 designation
to -70.
Table 5, Command Definitions
Address bits A0–A14 are required for unlock cycles.
Therefore, addresses for second and fifth write cycles
are 2AAAh in word mode and 5555h in byte mode. Ad-
dresses for first, third, fourth, and sixth cycles are
5555h in word mode and AAAAh in byte mode. Read
cycles are not affected. Deleted Note 5 to reflect the
correction.
AC Characteristics
Read Only Operations: Changed the -75 column head
to -70. All parameters remain the same.
Figure 7, Test Conditions: Changed CL in Note 1 from -
75 to -70.
Write/Erase/Program Operations: Changed the -75
column head to -70. Changed byte programming and
chip/sector erase times (tWHWH1 and tWHWH2, respec-
tively).
Revision C+2
AC Characteristics
Erase/Program Operations; Erase and Program Oper-
ations Alternate CE# Controlled Writes: Corrected the
notes reference for tWHWH1 and tWHWH2. These param-
eters are 100% tested. Corrected the note reference
for tVCS. This parameter is not 100% tested.
Switching Waveforms
Temporary Sector Unprotect Timing Diagram, Figure
18: Corrected the top waveform. RESET# begins at 0
V, then rises to 12 V in tVIDR
.
Temporary Sector Unprotect Table
AC Characteristics
Added note reference for tVIDR. This parameter is not
100% tested.
Alternate CE# Controlled Writes: Changed the -75 col-
umn head to -70. Changed byte programming and
Trademarks
Copyright © 1998 Advanced Micro Devices, Inc. All rights reserved.
AMD, the AMD logo, and combinations thereof are registered trademarks of Advanced Micro Devices, Inc.
ExpressFlash is a trademark of Advanced Micro Devices, Inc.
Product names used in this publication are for identification purposes only and may be trademarks of their respective companies.
36
Am29F100
相关型号:
AM29F100B-150FCB
1 Megabit (128 K x 8-bit/64 K x 16-bit) CMOS 5.0 Volt-only, Boot Sector Flash Memory
AMD
AM29F100B-150FE
1 Megabit (128 K x 8-bit/64 K x 16-bit) CMOS 5.0 Volt-only, Boot Sector Flash Memory
AMD
AM29F100B-150FEB
1 Megabit (128 K x 8-bit/64 K x 16-bit) CMOS 5.0 Volt-only, Boot Sector Flash Memory
AMD
AM29F100B-150FI
1 Megabit (128 K x 8-bit/64 K x 16-bit) CMOS 5.0 Volt-only, Boot Sector Flash Memory
AMD
AM29F100B-150FIB
1 Megabit (128 K x 8-bit/64 K x 16-bit) CMOS 5.0 Volt-only, Boot Sector Flash Memory
AMD
AM29F100B-150SC
1 Megabit (128 K x 8-bit/64 K x 16-bit) CMOS 5.0 Volt-only, Boot Sector Flash Memory
AMD
AM29F100B-150SCB
1 Megabit (128 K x 8-bit/64 K x 16-bit) CMOS 5.0 Volt-only, Boot Sector Flash Memory
AMD
AM29F100B-150SE
1 Megabit (128 K x 8-bit/64 K x 16-bit) CMOS 5.0 Volt-only, Boot Sector Flash Memory
AMD
AM29F100B-150SEB
1 Megabit (128 K x 8-bit/64 K x 16-bit) CMOS 5.0 Volt-only, Boot Sector Flash Memory
AMD
AM29F100B-150SI
1 Megabit (128 K x 8-bit/64 K x 16-bit) CMOS 5.0 Volt-only, Boot Sector Flash Memory
AMD
AM29F100B-150SIB
1 Megabit (128 K x 8-bit/64 K x 16-bit) CMOS 5.0 Volt-only, Boot Sector Flash Memory
AMD
AM29F100B-70EC
1 Megabit (128 K x 8-bit/64 K x 16-bit) CMOS 5.0 Volt-only, Boot Sector Flash Memory
AMD
©2020 ICPDF网 联系我们和版权申明